Statistical analysis of adsorption isotherm models and its appropriate selection

The application of Rumex Abysinicus derived activated carbon/bentonite clay/graphene oxide/iron oxide nanocomposite for removal of chromium from aqueous solution

Rapid industrialization has significantly boosted economic growth but has also introduced severe environmental challenges, particularly in water pollution. This study evaluates the effectiveness of a nanocomposite composed of Rumex Abyssinicus Activated Carbon/Acid Activated Bentonite Clay/Graphene Oxide, and Iron Oxide (RAAC/AABC/GO/Fe3O4) for chromium removal from aqueous solutions. The preparation of the nanocomposite involved precise methods, and its characterization was performed using Scanning Electron Microscopy (SEM), X-ray Diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR), Brunauer-Emmett-Teller (BET) surface area analysis, and the point of zero charge (pHpzc). Batch adsorption experiments were designed using Design Expert software with a central composite design under response surface methodology. The factors investigated included pH (3, 6, and 9), initial Cr (VI) concentration (40, 70, and 100 mg/L), adsorbent dose (0.5, 0.75, 1 g/200 mL), and contact time (60, 90, and 120 min). Adsorption isotherms were analyzed using nonlinearized Langmuir, Freundlich, and Temkin models, while pseudo-first-order and pseudo-second-order models were applied to adsorption kinetics. Characterization revealed a pHpzc of 8.25, a porous and heterogeneous surface (SEM), diverse functional groups (FTIR), an amorphous structure (XRD), and a significant surface area of 1201.23 m2/g (BET). The highest removal efficiency of 99.91% was achieved at pH 6, with an initial Cr (VI) concentration of 70 mg/L, a 90 min contact time, and an adsorbent dose of 1 g/200 mL. Optimization of the adsorption process identified optimal parameters as pH 5.84, initial Cr (VI) concentration of 88.94 mg/L, contact time of 60 min, and adsorbent dose of 0.52 g/200 mL. The Langmuir isotherm model, with an R2 value of 0.92836, best described the adsorption process, indicating a monolayer adsorption mechanism. The pseudo-second-order kinetics model provided the best fit with an R2 value of 0.988. Overall, the nanocomposite demonstrates significant potential as a cost-effective and environmentally friendly solution for chromium removal from wastewater.

Effect of chitosan coating on basil (Ocimum sanctum) leaves dried by microwave-assisted drying method: Analysis of color, effective moisture diffusivity, and drying kinetics

Basil (Ocimum sanctum) leaves, commonly known as holy basil, have various health benefits due to their rich phytochemical content. However, fresh basil leaves face challenges related to their perishability and short shelf life. This study explores the use of edible coating, specifically chitosan, to extend the shelf life of basil leaves. Then basil leaves with chitosan coating were dried using microwave-assisted drying (MAD) method with variations of microwave power (136, 264, 440, and 616 W), mass of basil leaves (5, 10, and 15 g), and chitosan concentration (0, 2.5, and 5 %). The purpose of this study is to analyze the color, effective moisture diffusivity, and drying kinetics. Five mathematical models and seven error functions were used. The Avhad and Marchetti Model was identified as the most suitable model to describe the drying kinetics of basil leaves with chitosan coating. The Deff value increased with decreasing mass of basil leaves, decreasing chitosan concentration, and increasing microwave power. Deff values ranged from 0.001 to 0.002 m2/s. The thickness of the basil leaves also played a role in the fluctuation of Deff values. The highest ΔE value was obtained by 5 % concentration of chitosan. The chitosan coating, especially at a concentration of 2.5 %, showed discoloration indicating better preservation of the original color of basil leaves. In conclusion, this study shows that chitosan coating and MAD are effective strategies to extend the shelf life of basil leaves and can provide valuable insights for future applications in leaf drying or thin layer drying processes.

Management of ibuprofen in wastewater using electrospun nanofibers developed from PET and PS wastes

Electrospinning is a promising technique for the beneficial use and recycling of plastic waste polymers using simple methodologies. In this study, plastic bottles and Styrofoam wastes have been used to develop polyethylene terephthalate (PET) and polystyrene (PS) nanofibers using electrospinning technique separately without any further purification. The effect of the concentration onto the nanofiber's morphology was studied. The fabricated nanofibers were characterized using Field Emission Scanning Electron Microscope (FE-SEM), Fourier Transformed Infrared Spectroscopy (ATR-FTIR), N2 adsorption/desorption analysis, and water contact angle (WCA). Furthermore, the prepared nanofibers were applied for the adsorption of ibuprofen (IBU) from wastewater. Some parameters that can influence the adsorption efficiency of nanofibers such as solution pH, wt.% of prepared nanofibers, drug initial concentration, and contact time were studied and optimized. The results show that the equilibrium adsorption capacity was achieved after only 10 min for 12 wt% PET nanofibers which is equivalent to 364.83 mg/g. For 12 wt% PS nanofibers, an equilibrium adsorption capacity of 328.42 mg/g was achieved in 30 min. The experimental data was fitted to five isotherm and four kinetics models to understand the complicated interaction between the nanofibers and the drug. Langmuir-Freundlich isotherm model showed the best fit for experimental data for both PET and PS nanofibers. The adsorption process was characterized by predominantly physical reaction rather than chemical adsorption for both materials. The reusability study revealed that the synthesized nanofibers maintain their ability to adsorb/desorb IBU for up to five cycles. The results obtained demonstrated that fabricated nanofibers from plastic wastes could perform promising adsorbents for the management of IBU in wastewater. However, further research is needed for the scaling-up the fabrication which is required for real-world applications.

Adsorption of Cd (II) ions and methyl violet dye by using an agar-graphene oxide nano-biocomposite

In this work, an agar-graphene oxide hydrogel was prepared to adsorb Cd (II) and Methyl Violet (MV) from water. The hydrogel was synthesised and characterised through SEM and EDS. Kinetic, equilibrium and regeneration studies were carried out, in which Langmuir, Freundlich and Sips isotherm models were fitted to the equilibrium experimental data; and regarding the kinetics, studies were conducted by modelling experimental data considering both empirical and phenomenological models. SEM and EDS have shown the composite present a 3D-disordered porous microstructure and that it is mainly constituted of C and O. Sips model fitted well to Cd (II) (R2 = 0.968 and χ2 =  0.176) and MV (R2 = 0.993 and χ2 =  0.783). The qmax values for MV and Cd (II) were 76.65 and 11.70 mg.g-1, respectively. Pseudo-order models satisfactorily described Cd (II) and MV adsorption kinetics with R2 > 0.90. Regeneration experiments revealed an outstanding reuse capacity of the adsorbent after three cycles of adsorption-desorption for both Cd (II) and MV. This study evidences the possibility of a feasible adsorbent for Cd (II) and MV removal from water for successive cycles of use.

One-step fabrication of millimeter-scale hollow vesicles with chitosan /DADMAC/ sodium alginate graft copolymer for enhanced anionic dye adsorption

Hollow vesicles are promising in water treatment due to their unique structure of the membrane and inner cavity. However, the adsorption capacity needs to be improved for targeted pollutants. Herein, millimeter-scale hollow vesicles were prepared with a one-step process of sequential stirring and grafting using chitosan, diallyldimethylammonium chloride, and sodium alginate as raw materials with the purpose of efficient removal of anionic dyes from wastewater. The composite vesicles were characterized using scanning electron microscopy, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, and X-ray diffraction. The hollow vesicles showed the structure of the cationic membrane and the inner cavity, facilitating the dye adsorption. The adsorption capacity for the anionic dye Reactive Black 5 reached 698.1 mg/g, more than twice that of the binary composite vesicles without graft. The adsorption kinetics and isotherm data coincided with the pseudo-second-order and Langmuir models, respectively, and the adsorption mechanism was monolayer chemisorption. Moreover, the vesicles worked well in wide ranges of environment pH, temperature, and co-existing pollutants. They also possessed excellent cyclic regeneration performance, in which 93 % of the initial adsorption capacity was maintained after four cycles. These results indicate that the millimeter-scale hollow vesicles exhibit broad application prospects for wastewater purification.

Highly efficient targeted adsorption and catalytic degradation of ciprofloxacin by a novel molecularly imprinted bimetallic MOFs catalyst for persulfate activation

Given the presence of emerging pollutants at low concentrations in water bodies, which are inevitably affected by background substances during the removal process. In this study, we synthesized molecularly imprinted catalysts (Cu/Ni-MOFs@MIP) based on bimetallic metal-organic frameworks for the targeted degradation of ciprofloxacin (CIP) in advanced oxidation processes (AOPs). The electrostatic interaction and functional group binding of CIP with specific recognition sites on Cu/Ni-MOFs@MIP produced excellent selective recognition (Qmax was 14.82 mg g-1), which enabled the active radicals to approach and remove the contaminants faster. Electron paramagnetic resonance (EPR) analysis and quenching experiments revealed the coexistence of ∙OH, SO42-, and 1O2, with ∙OH dominating the system. Based on experimental and theoretical calculations, the reaction sites of CIP were predicted and the possible degradation pathways and mechanisms of Cu/Ni-MOFs@MIP/PMS systems were proposed. This study opens up a new platform for the targeted removal of target pollutants in AOPs.

Bifunctional Protein TC1 Mediated One-Pot Strategy for Robust Immobilization of DNA with High Accessibility

Immobilizing DNA with high accessibility at the interface is attractive but challenging. Current methods often involve multiple chemical reactions and derivatives. In this study, an endonuclease, TC1, is introduced to develop a robust strategy for immobilizing DNA with enhanced accessibility. TC1 enables direct immobilization of DNA onto a solid support through self-catalytic DNA covalent coupling and robust solid adsorption capabilities. This method demonstrates high accessibility to target molecules, supported by the improved sensitivity of DNA hybridization and aptamer-target recognition assays. TC1-mediated DNA immobilization is a one-pot reaction that does not require chemical derivatives, making it promising for the development of high-performance DNA materials and technologies.

Removal of lead ions from aqueous solution by modified nanocellulose

Heavy metals significantly impact the environment due to their non-biodegradable, toxic, and carcinogenic behaviors. Lead contaminants impose severe health impacts on humans and the water environment. Therefore, eco-friendly and efficient lead ion removal practices such as nanotechnology are an urgent requirement for the abatement of lead pollution. In the present study, nanocellulose was synthesized from the cotton straw residue using chemical methods and modified with titanium dioxide to form a nanocomposite. The nanocomposite synthesized was characterized by using FTIR, XRD, FESEM, and BET. FTIR results noticed peaks at 1648.43 and 1443.57 cm-1 for cellulose and Ti-O-Ti bonding at 505.02 cm-1. The nanocomposite was noticed to be disordered and irregular in shape. The nanocomposite has particle sizes of 83 nm. The nanocomposite crystalline particle had 65% anatase and 32% rutile phases observed from the XRD result. BET results show that the surface area of nanocellulose increases after surface modification from 25.692 to 42.510 m2/g. The adsorption capacity of the nanocomposite was 0.552 mg/g was noticed. The Elovich kinetic and Baudu isotherms are the best-fitted models for lead ion adsorption. Thermodynamic parameters resulted in Gibbs free energy decreasing with temperature. This study revealed that modified cellulosic adsorbents efficiently absorbed lead ions derived from cotton straws.

Thermodynamic and structural investigation of oily wastewater treatment using peach kernel and walnut shell based activated carbon

Despite the many articles about activated carbon with different precursors in adsorption process, no in-depth research has been carried out to understand the causes of the difference in surface adsorption characteristics of activated carbon with different precursors and different activation processes. In this work, the ability of two active carbon adsorbents made of walnut shell and peach kernel by two chemical and physical methods (totally 4 different types of activated carbon) in treatment of oily wastewater including diesel, gasoline, used oil or engine lubricant has been compared. The results show that the chemical activated peach carbon active with 97% hardness has provided the highest hardness and physical activated walnut carbon active has obtained the lowest hardness value (87%). It is also found that peach activated carbon has a higher iodine number than walnut activated carbon, and this amount can be increased using chemical methods; Therefore, the highest amount of Iodine Number is related to Peach activated carbon that is made by chemical method (1230 mg/g), and the lowest amount of iodine number is seen in walnut activated carbon that is made by physical method (1020 mg/g). moreover, the pore diameter of physical activated carbon is lower than chemical activated carbon in all cases. So that the pore diameter of chemical activated peach carbon active is equal to 22.08 μm and the measured pore diameter of physical activated peach carbon active is equal to 20.42 μm. These values for walnut are obtained as 22.74 μm and 21.86 μm, respectively. Furthermore, the temperature and pH effects on the adsorption of different synthesized oily wastewater was studied and it was found that a decrease in adsorption can be seen with an increase in temperature or decreasing the pH value, which can be referred to this fact that the process of adsorption is an exothermic process. Finally, to analyze the compatibility of adsorption isotherms with experimental data and to predict the adsorption process, three different isotherms named Langmuir, Temkin, and Freundlich isotherms were applied and their parameters were correlated. The correlation results show that the Langmuir isotherm had the best correlation in all cases compared to the Freundlich and Temkin isotherms, based on the correlation coefficient, and the calculated R2 values which was greater than 0.99 in all the studied cases.

How do polystyrene microplastics affect the adsorption of copper in soil?

Microplastics (MPs) commonly coexist with heavy metals in the soil environment. MPs can influence the activity of heavy metals, and the specific mechanisms need to be further explored. Here, different contents of polystyrene (PS) MPs were added to soil to explore their effects on the adsorption and desorption characteristics of copper (Cu2+) in soil. The adsorption process was mainly chemical adsorption and belonged to a spontaneous, endothermic reaction. The hydrophobicity of MPs slowed down the adsorption and desorption rates. The main adsorption mechanisms included complexation by oxygen-containing functional groups, ion exchange (accounting for 33.97-36.04 % of the total adsorption amounts), and electrostatic interactions. MPs lacked oxygen-containing functional groups and were predominantly engaged in ion exchange and electrostatic interactions. MPs diluted, blocked the soil, and covered the active sites of soil, which reduced adsorption (3.56-16.18 %) and increased desorption (0.90-2.07 %) of Cu2+ in soil samples, thus increasing the activity and mobility of Cu2+. These findings provide new insights into the effects of MPs on the fate and risk of heavy metals in soil. ENVIRONMENTAL IMPLICATION: The existing literature concerning the effects of microplastics on the adsorption of heavy metals in soil is insufficient. Our investigation unveiled that the main adsorption mechanisms of different soil samples included complexation by oxygen-containing functional groups, ion exchange (accounting for 33.97-36.04 % of the total adsorption amounts), and electrostatic interactions. MPs lacked oxygen-containing functional groups and were predominantly engaged in ion exchange and electrostatic interactions. MPs diluted, blocked the soil, and covered the active sites of soil, which reduced adsorption (3.56-16.18 %) and increased desorption (0.90-2.07 %) of Cu2+ in soil samples, thus increasing the activity and mobility of Cu2+.

Porous sulfur polymers for effective aqueous-phase organic contaminant removal

Sulfur polymers produced through 'inverse vulcanization' exhibit various attributes, such as photocatalytic activity and a high capacity to adsorb heavy metals. Nevertheless, there is a lack of research investigating the use of sulfur polymers as materials for the removal of organic contaminants. In this work, porous sulfur polymers (PSPs) were synthesized from elemental sulfur and 1,3-diisopropenylbenzene, with porosity introduced via salt templating. The result is a material that can strongly adsorb and chemically neutralize a model organic contaminant (caffeine). PSPs show adsorption up to 5 times higher than a leading adsorption material (activated carbon). Furthermore, either the adsorption or degradation processes can govern the removal efficiency depending on the synthesis parameters of PSPs. This is the first-ever report demonstrating sulfur polymers as effective materials for removing emerging contaminants from water. The versatile synthesis of sulfur polymers offers variation, which means that there is much more to explore in this exciting research area.

Use of Time-Domain NMR for 1H T1 Relaxation Measurement and Fitting Analysis in Homogeneity Evaluation of Amorphous Solid Dispersion

This study examined the usefulness of 1H T1 relaxation measurements for evaluating the homogeneity of amorphous solid dispersion (ASD). Indomethacin and polyvinylpyrrolidone were used to prepare two kinds of ASDs. One was inhomogeneous ASD (ASDmelt) prepared by a melt-quenching method, and the other was homogeneous ASD (ASDsolvent) prepared by a solvent evaporation method. The T1 relaxation was measured by the time-domain NMR (TD-NMR) technique using a low-field NMR system. Curve-fitting analysis of T1 relaxation plots was conducted using the Akaike information criterion. This fitting analysis revealed that the T1 relaxation of ASDmelt and ASDsolvent was biphasic and monophasic, respectively. ASDmelt and ASDsolvent were inhomogeneous and homogeneous on a nanometer scale, respectively, considering the spin diffusion of 1H nuclei. These T1 results were consistent with the Raman mapping of ASDs. From the fitting analysis of 1H T1 relaxation, we conclude that TD-NMR is a promising technique for evaluating ASD homogeneity.

Comparative Investigation of Phosphate Adsorption Efficiencies of MOF-76 (Ce) and Metal Oxides Derived from MOF-76 (Ce)

Phosphate pollution is a very challenging problem for the water environment. Phosphate mixed with water in various ways causes eutrophication. To sustain life in aquatic systems, phosphate ions must be cleaned. Therefore, it is very important to remove phosphate in wastewater. Here, an adsorption method has been tried for the removal of phosphate. MOF-76 (Ce), a cerium-based metal-organic framework, was synthesized by a hydrothermal method. Since metal oxides are known to be successful in phosphate adsorption, CeO2 nanoparticles were also obtained by pyrolysis of this MOF structure. The phosphate adsorption efficiencies of both adsorbents were compared. The characterization methods (SEM, FTIR, XRD, and TGA) were applied to adsorbents. The kinetic, isotherm, and thermodynamics studies were applied to experimental results. At 298 K, the adsorption capacity of MOF-76 (Ce) is higher than that of CeO2, according to Langmuir isotherm qm values. The qm values are 72.97 and 55.71 mg/g, respectively. Both adsorbents follow the pseudo second-order kinetic model. It has been found that MOF-76 (Ce) has a pH-selective property in phosphate adsorption. No change was observed in the phosphate adsorption capacity of CeO2 with pH. In terms of thermodynamics, the endothermic reaction is valid for both adsorbents.

The mechanism and behavior of cesium adsorption from aqueous solutions onto carbonated cement slurry powder

In this study, microstructural differences and changes in the adsorption capacity of cesium between cement and carbonated cement were investigated. Cement blocks were ground to powder for rapid carbonation, and microscopic variations were characterized by XRF, XRD, FT-IR, SEM, BET, and TGA. The characterization results show that the conversion of Ca(OH)2 and calcium silicate hydrate (C-S-H) gel to CaCO3 in cement after carbonation. And the component of Ca(OH)2 in the powder sample disappeared after three days of rapid carbonation. Batch experiments were used to investigate adsorption under the influence of time, initial cesium concentration, temperature, and ion coexistence. Pseudo-second-order kinetic and Langmuir isothermal model fitting could better describe the adsorption process and the results show that the maximum adsorption capacity of cement after carbonation surges from 29.6 μg‧g-1 to 1.58-5.89 mg‧g-1. (Different carbonating times lead to varying adsorption capacity.) The adsorption capacity decreases with increasing temperature. At temperatures of 293 K and 333 K, the calculated Gibbs free energy change values of cement with different carbonated degrees adsorbing cesium are -10.3 ∼ -14.9 kJ‧mol-1 and -8.03 ∼ -12.4 kJ‧mol-1. And the calculated values of enthalpy change and entropy change are -18.8 ∼ -23.8 kJ‧mol-1 and -27.9 ∼ -37.1 J‧mol-1‧K-1. Combining the characterization and adsorption results, the huge increase in cesium adsorption capacity is closely related to the conversion of Ca(OH)2 to CaCO3, which will provide a new perspective on the adsorption mechanism of cesium in cement.

Adsorption of trace heavy metals through organic compounds enriched biochar using isotherm adsorption and kinetic models

Trace heavy metals such as copper and nickel, when exceeds a certain level, cause detrimental effects on the ecosystem. The current study examined the potential of organic compounds enriched rice husk biochar (OCEB's) to remove the trace heavy metals from an aqueous solution in four steps. In 1st step, biochar' physical and chemical properties were analyzed through scanning electron microscope (SEM) and Fourier transforms infrared spectroscopy (FTIR). In the 2nd step, two biochar vis-a-vis glycine, alanine enriched biochar (GBC, ABC) was selected based on their adsorption capacity of four different metals Cr, Cu, Ni and Pb (chromium, copper, nickel, and lead). These two adsorbents (GBC, ABC) were further used to evaluate the best interaction of biochar for metal immobilization based on varying concentrations and times. Langmuir isotherm model suggested that the adsorption of Ni and Cu on the adsorbent surface supported the monolayer sorption. The qmax value of GBC for Cu removal increased by 90% compared to SBC (Simple rice husk biochar). The interaction of Cu and Ni with GBC and ABC was chemical, and 10 different time intervals were studied using pseud first and second-order kinetics models. The current study has supported the pseudo second-order kinetic model, which exhibited that the sorption of Ni and Cu occurred due to the chemical processes. The % removal efficiency with GBC was enhanced by 21% and 30% for Cu and Ni, respectively compared to the SBC. It was also noticed that GBC was 21% more efficient for % removal efficiency than the CBC. The study's findings supported that organic compound enriched rice husk biochar (GBC and ABC) is better than SBC for immobilizing the trace heavy metals from an aqueous solution.

Adsorption potential of orange rind-based nanosorbents for the removal of cadmium(II) and chromium(VI) from contaminated water

Heavy metals (HMs) in water are highly poisonous and carcinogenic agents for human health. To alleviate the toxic impacts of HMs, green remediation technologies are the need of the hour. In this regard, different nanosorbents (CMCG@ORP, ORAC, NiO/NPs, and NiO@ORAC/NCs) were synthesized in the present study, and the percentage removal of heavy metals [chromium(VI) and cadmium(II) ions] was evaluated. The nanosorbents were characterized by using FTIR, SEM, UV-Vis spectroscopy, and XRD. UV-Vis spectroscopy confirmed the synthesis of nanosorbents such as NiO/NPs and NiO@ORAC/NCs at 330.5 nm and 352.55 nm, respectively. The characterization studies show that the surface of synthesized nano-sorbents was highly coarse, uneven, and abrasive. XRD pattern deduced that the sample was of single phase, and no other impurity was detected except the face-centered cubic-phase peak of NiO. The maximum adsorption of Cd (91%) and Cr (92%) was found at initial concentrations of 100 and 60 ppm respectively at contact time = 180 min, temperature 25 °C, and with an adsorbent dose of 0.5 g. Isothermal, kinetic, and thermodynamic studies were also performed to evaluate the adsorption mechanisms and feasibility of the process. Adsorption mostly followed Freundlich isotherm which indicates the multilayer adsorption phenomenon and the negative value of Gibb's free energy showed the spontaneous nature and feasibility of the adsorption reaction. Surface complexation, ion exchange, surface precipitation, and the phenomenon of physical adsorption occurred on the sorbent surface which led to the attachment of Cd and Cr to the tested nanosorbents. In conclusion, NiO@ORAC/NCs were the most effective in the alleviation of Cd(II) and Cr(VI) ions in contaminated water.

In situ preparation of MOF-199 into the carrageenan-grafted-polyacrylamide@Fe3O4 matrix for enhanced adsorption of levofloxacin and cefixime antibiotics from water

In this research study, a novel method, an in-situ growth approach, to incorporate metal-organic framework (MOF) into carrageenan-grafted- polyacrylamide-Fe3O4 substrate was introduced. Carrageenan-grafted-polyacrylamide-Fe3O4/MOF nanocomposite (kC-g-PAAm@Fe3O4-MOF-199) was fabricated utilizing three stages. In this way, the polyacrylamide (PAAm) was grafted onto the carrageenan (kC) backbone via free radical polymerization in the presence of methylene bisacrylamide (MBA) as cross-linker and Fe3O4 magnetic nanoparticles. Next, the kC-g-PAAm@Fe3O4 was modified by MOF-199 via an in-situ solvothermal approach. Several analyses such as Fourier transform infrared spectroscopy (FT-IR), X-Ray diffraction (XRD), field emission scanning electron microscopy (FESEM), energy-Dispersive X-ray Spectroscopy (EDX), thermogravimetric analysis (TGA), vibrating sample magnetometer (VSM), Brunauer-Emmett-Teller (BET) demonstrated the successful synthesis of kC-g-PAAm@Fe3O4-MOF-199 magnetic hydrogel nanocomposite. The XRD pattern of magnetic hydrogel nanocomposite illustrated characteristic peaks of Fe3O4, neat kC, and MOF-199 with enhanced crystallinity in comparison with kC-g-PAAm@Fe3O4. TGA showed it has a char yield of 24 wt% at 800 °C. VSM confirmed its superparamagnetic behavior (with Ms of 8.04 emu g-1), and the BET surface area of kC-g-PAAm@Fe3O4-MOF-199 was measured at 64.864 m2 g-1, which was higher than that of kC-g-PAAm@Fe3O4 due to the highly porous MOF-199 incorporation with a BET surface area of 905.12 m2 g-1). The adsorption effectiveness of kC-g-PAAm@Fe3O4-MOF-199 for eliminating cephalosporin and quinolones antibiotics, i.e., Cefixime (CFX) and Levofloxacin (LEV) from the aquatic area was considered. Several experimental setups were used to evaluate the efficacy of adsorption, such as solution pH, amount of adsorbent, contact duration, and initial concentration. The maximum adsorption capacity (Qmax) of the prepared magnetic hydrogel nanocomposite was found to be 2000 and 1666.667 mg-1 for LEV and CFX using employing 0.0025 g of adsorbent. The Freundlich isotherm model well described the experimental adsorption data with R2CFX = 0.9986, and R2LEV = 0.9939. And the adsorption kinetic data were successfully represented by the pseudo-second-order model with R2LEV = 0.9949 and R2CFX = 0.9906. Hydrogen bonding, π-π interaction, diffusion, and entrapment in the hydrogel network all contributed to the successful adsorption of both antibiotics onto the kC-g-PAAm@Fe3O4-MOF-199 adsorbent. Other notable physicochemical properties include the three-dimensional structure and availability of the reactive adsorption sites. Moreover, the adsorption/desorption efficacy of magnetic hydrogel nanocomposites was not significantly diminished after four cycles of recovery.

2-Methyl-4-chlorophenoxyacetic acid (MCPA) sorption and desorption as a function of biochar properties and pyrolysis temperature

2-Methyl-4-chlorophenoxyacetic acid (MCPA) is a highly mobile herbicide that is frequently detected in global potable water sources. One potential mitigation strategy is the sorption on biochar to limit harm to unidentified targets. However, irreversible sorption could restrict bioefficacy thereby compromising its usefulness as a vital crop herbicide. This research evaluated the effect of pyrolysis temperatures (350, 500 and 800°C) on three feedstocks; poultry manure, rice hulls and wood pellets, particularly to examine effects on the magnitude and reversibility of MCPA sorption. Sorption increased with pyrolysis temperature from 350 to 800°C. Sorption and desorption coefficients were strongly corelated with each other (R2 = 0.99; P < .05). Poultry manure and rice hulls pyrolyzed at 800°C exhibited irreversible sorption while for wood pellets at 800°C desorption was concentration dependent. At higher concentrations some desorption was observed (36% at 50 ppm) but was reduced at lower concentrations (1-3% at < 5 ppm). Desorption decreased with increasing pyrolysis temperature. Sorption data were analyzed with Langmuir, Freundlich, Dubinin-Radushkevich and Temkin isotherm models. Freundlich isotherms were better predictors of MCPA sorption (R2 ranging from 0.78 to 0.99). Poultry manure and rice hulls when pyrolyzed at higher temperatures (500 and 800°C) could be used for remediation efforts (such as spills or water filtration), due to the lack of desorption observed. On the other hand, un-pyrolyzed feedstocks or biochars created at 350°C could perform superior for direct field applications to limit indirect losses including runoff and leaching, since these materials also possess the ability to release MCPA subsequently to potentially allow herbicidal action.

Enhanced Reactive Brilliant Blue Removal Using Chitosan-Biochar Hydrogel Beads

To address the challenges associated with the weak affinity and difficult separation of biochar, we developed chitosan-biochar hydrogel beads (CBHBs) as an efficient solution for removing reactive brilliant blue (RBB KN-R) from wastewater. The adsorption behavior and mechanism of RBB KN-R onto CBHBs were extensively studied. Notably, the adsorption capacity of RBB KN-R showed pH-dependence, and the highest adsorption capacity was observed at pH 2. The adsorption process was well fitted with the pseudo-second-order kinetic model and the intraparticle diffusion model. Film diffusion and intraparticle diffusion were both responsible for the adsorption of RBB KN-R onto CBHBs. At 298.15 K, the maximum adsorption capacity qm was determined to be 140.74 mg/g, with higher temperatures favoring the adsorption process. A complex mechanism involving π-π interactions, electrostatic attraction, hydrophobic interaction, and hydrogen bonding was found to contribute to the overall adsorption process. The experimental data discovered the coexisting substances and elevated ionic strength hindered the adsorption capacity. Significantly, after three cycles of adsorption-desorption, the CBHBs maintained an adsorption capacity above 95% for RBB KN-R. These promising results imply that CBHBs are a durable and cost-effective adsorbent for efficient removal of dyes from wastewater.

Adsorption of chloroquine, propranolol, and metformin in aqueous solutions using magnetic graphene oxide nanocomposite

The work proposes the application of a nanocomposite formed by graphene oxide and magnetite to remove chloroquine, propranolol, and metformin from water. Tests related to adsorption kinetics, equilibrium isotherms and adsorbent reuse were studied, and optimization parameters related to the initial pH of the solution and the adsorbent dosage were defined. For all pharmaceuticals, adsorption tests indicated that removal efficiency was independent of initial pH at adsorbent dosages of 0.4 g L-1 for chloroquine, 1.2 g L-1 for propranolol, and 1.6 g L-1 for metformin. Adsorption equilibrium was reached within the first few minutes, and the pseudo-second-order model represented the experimental data well. While the equilibrium data fit the Sips isotherm model at 298 K, the predicted maximum adsorption capacities for chloroquine, propranolol, and metformin were 44.01, 16.82, and 12.23 mg g-1, respectively. The magnetic nanocomposite can be reused for three consecutive cycles of adsorption-desorption for all pharmaceuticals, being a promising alternative for the removal of different classes of pharmaceuticals in water.

Mussel inspired synthesis of polydopamine/polyethyleneimine-grafted fly ash composite adsorbent for the effective separation of U(VI)

Polydopamine/polyethyleneimine-grafted fly ash composite (PDA/PEI/FA), an efficient multifunctional adsorbent for U(VI) with excellent separation efficiency (94.5 %) and capacity (422.5 mg/g), was synthesized by grafting PDA and PEI on FA via Mussel inspiration and Michael addition reaction. The introduction of PDA and PEI had brought numerous functional groups with fine affinities to uranium, like catechol, amino and imino, causing good U(VI) separation performances. Langmuir and Pseudo-second-order models were well matched with experimental data, illustrating the U(VI) separation on PDA/PEI/FA was a homogeneous chemical adsorption process. After five cycles, the U(VI) adsorption efficiency for PDA/PEI/FA was still up to 90.2 %, implying that PDA/PEI/FA possessed good stability and reusability. Besides, the good dynamic adsorption performances of PDA/PEI/FA further demonstrated that PDA/PEI/FA was an ideal adsorbent for the practical wastewater treatment. According to the characterization results, U(VI) was absorbed by PAD/PEI/FA through complexation, redox reaction, electrostatic attraction and hydrogen bonding. Given the above, PDA/PEI/FA showed good practical application prospect in U(VI) separation.

Highly efficient removal of Pb2+ from wastewater by a maleic anhydride modified organic porous adsorbent

Sorption is prominent in low price, high efficiency, availability, and eco-friendliness. Organic porous materials have the characteristics of easy functionalization, diverse structure and stability, and show great potential in adsorption, energy storage, catalysis, and other fields. A mesoporous phenolic resin-type polymer (PRP) was successfully synthesized and modified by solid state reaction with maleic anhydride to prepare adsorbent (called as PRP-MAH) for sorption of Pb²⁺. The impact of reaction conditions (the pH value, reaction temperature, fresh concentration of solution, ionic strength and reaction time, etc.) was systematically studied. Characterization methods such as SEM, FTIR, and XPS indicated that the synthesized adsorbent PRP-MAH had regular morphology and good stability. The fitting of isothermal adsorption experiment data conforms to Langmuir sorption isotherm, and the sorption capacity reached 366.40 mg·g^-1 at 308 K. The kinetic data were consistent with the quasi-second-order model, which indicated that the chemisorption might play the main role in the sorption process. Thermodynamic research manifested that the sorption of Pb²⁺ by PRP-MAH was carried out by a spontaneous process at the study temperature. The studies show that PRP-MAH can remove Pb²⁺ from water solution through ion exchange, electrostatic attraction, and surface complexation.

Citrus fruit residues as alternative precursors to developing H2O and CO2 activated carbons and its application for Cu(II) adsorption

Due to its toxicity, the presence of Cu(II) ions released in aquatic environments presents a serious threat to the environment and human health. In search of sustainable and low-cost alternatives, there are citrus fruit residues, which are generated in large quantities by the juice industries and can be used to produce activated carbons. Therefore, the physical route was investigated for producing activated carbons to reuse citrus wastes. In this work, eight activated carbons were developed, varying the precursor (orange peel-OP, mandarine peel-MP, rangpur lime peel-RLP, and sweet lime peel-SLP) and the activating agent (CO₂ and H₂O) to remove Cu(II) ions of the aqueous medium. Results revealed promising activated carbons with a micro-mesoporous structure, a specific surface area of around 400 m² g^-1, and a pore volume of around 0.25 cm³ g^-1. In addition, Cu (II) adsorption was favored at pH 5.5. The kinetic study showed that the equilibrium was reached within 60 min removing about 80% of Cu(II) ions. The Sips model was the most suitable for the equilibrium data, providing maximum adsorption capacities (qmS) values of 69.69, 70.27, 88.04, 67.83 mg g^-1 for activated carbons (AC-CO₂) from OP, MP, RLP, and SLP, respectively. The thermodynamic behavior showed that the adsorption process of Cu(II) ions was spontaneous, favorable, and endothermic. It was suggested that the mechanism was controlled by surface complexation and Cu²⁺-π interaction. Desorption was possible with an HCl solution (0.5 mol L^-1). From the results obtained in this work, it is possible to infer that citrus residues could be successfully converted into efficient adsorbents to remove Cu(II) ions from aqueous solutions.

A new strategy for treating Pb2+ and Zn2+ pollution with industrial waste derivatives Humin

Metal pollution caused by industrial waste accumulation is a long-term and far-reaching problem. Humin (HM), as a highly condensed organic component insoluble in alkaline or water solution, is often discarded as humic acid industrial waste. However, the abundant active functional groups in HM reported by some researches make it possible for HM to remove metals. In this study, a waste reuse strategy was proposed to reduce the pressure of industrial metal pollution on the environment. HM was obtained from lignite waste residue. Scanning electron microscopy, energy spectrum and Fourier infrared spectroscopy, combined with the adsorption models were employed to reveal the mechanism of HM adsorption. The results showed that HM had multiple adsorption mechanism and high biological stability. The adsorption capacity of HM to Zn²⁺ and Pb²⁺ were 194.88 mg/g and 289.59 mg/g respectively. HM adsorbed Zn²⁺ mainly by physical multilayer adsorption. And the adsorption of Pb²⁺ by HM was mainly a monolayer chemical reaction, which depended on its active functional groups and the exchange of valence electrons. Notably, HM could simultaneously remove Pb²⁺ and Zn²⁺ and almost did not affect its original adsorption capacity to single ions. These results will provide a new strategy for the treatment of metal pollution in the future and alleviate the pressure of multiple metal pollution of the environment.

Lignin nanoparticle-decorated nanocellulose cryogels as adsorbents for pharmaceutical pollutants

Adsorption is a relatively simple wastewater treatment method that has the potential to mitigate the impacts of pharmaceutical pollution. This requires the development of reusable adsorbents that can simultaneously remove pharmaceuticals of varying chemical structure and properties. Here, the adsorption potential of nanostructured wood-based adsorbents towards different pharmaceuticals in a multi-component system was investigated. The adsorbents in the form of macroporous cryogels were prepared by anchoring lignin nanoparticles (LNPs) to the nanocellulose network via electrostatic attraction. The naturally anionic LNPs were anchored to cationic cellulose nanofibrils (cCNF) and the cationic LNPs (cLNPs) were combined with anionic TEMPO-oxidized CNF (TCNF), producing two sets of nanocellulose-based cryogels that also differed in their overall surface charge density. The cryogels, prepared by freeze-drying, showed layered cellulosic sheets randomly decorated with spherical lignin on the surface. They exhibited varying selectivity and efficiency in removing pharmaceuticals with differing aromaticity, polarity and ionic characters. Their adsorption potential was also affected by the type (unmodified or cationic), amount and morphology of the lignin nanomaterials, as well as the pH of the pharmaceutical solution. Overall, the findings revealed that LNPs or cLNPs can act as functionalizing and crosslinking agents to nanocellulose-based cryogels. Despite the decrease in the overall positive surface charge, the addition of LNPs to the cCNF-based cryogels showed enhanced adsorption, not only towards the anionic aromatic pharmaceutical diclofenac but also towards the aromatic cationic metoprolol (MPL) and tramadol (TRA) and neutral aromatic carbamazepine. The addition of cLNPs to TCNF-based cryogels improved the adsorption of MPL and TRA despite the decrease in the net negative surface charge. The improved adsorption was attributed to modes of removal other than electrostatic attraction, and they could be π-π aromatic ring or hydrophobic interactions brought by the addition of LNPs or cLNPs. However, significant improvement was only found if the ratio of LNPs or cLNPs to nanocellulose was 0.6:1 or higher and with spherical lignin nanomaterials. As crosslinking agents, the LNPs or cLNPs affected the rheological behavior of the gels, and increased the firmness and decreased the water holding capacity of the corresponding cryogels. The resistance of the cryogels towards disintegration with exposure to water also improved with crosslinking, which eventually enabled the cryogels, especially the TCNF-based one, to be regenerated and reused for five cycles of adsorption-desorption experiment for the model pharmaceutical MPL. Thus, this study opened new opportunities to utilize LNPs in providing nanocellulose-based adsorbents with additional functional groups, which were otherwise often achieved by rigorous chemical modifications, at the same time, crosslinking the nanocellulose network.

Universal Langmuir and Fractal Analysis of High-Resolution Adsorption Isotherms of Argon and Nitrogen on Macroporous Silica

High-resolution isotherms of argon and nitrogen adsorption on macroporous silica have been simulated with universal Langmuir and fractal models. A four-parameter, fractal universal Langmuir equation is a good fit to the data at low pressures. Standard Gibbs energy changes calculated from equilibrium adsorption coefficients show a series of broad peaks that indicate adsorbate structural transformations as a function of pressure and coverage. The Freundlich equation or mean fractal model is also a good fit to isotherms at low pressures. Pressure-varying fractals are accurate fits to the data. Fractal exponents provide information on adsorbate coverage and surface access. Broad peaks in pressure-varying exponents are indicators of adsorbate structure. From adsorptive gas amounts, mean and pressure-varying fractal exponents provide details of adsorbate fractal dimensions and surface roughness. Both Ar and N₂ adsorption cause increases in mean surface roughness when compared with pure silica. Surface roughness fluctuations from pressure-dependent adsorptive gas fractal dimensions are associated with adsorbate structure. At one trough, the surface is smooth and is linked to close-packed Ar or N₂. For Ar adsorption at 87 K, this structure is a complete monolayer (1.00(4)), while for Ar (77 K), 1.15(4) layers and for N₂ (87 K), 2.02(10) layers. The universal Langmuir specific area of the silica is 10.1(4) m² g^-1. Pressure- and coverage-dependent adsorbate structures range from filling defects and holes on the surface to cluster formation to adsorbed Ar or N₂ evenly distributed or packed across the surface. The Ar (87 K) isotherm is most sensitive to adsorbate structural transformations.

Preparation and Boron Removal Performance of Glycidol Modified PANI Nanorods: An Optimization Study Based on Response Surface Methodology

Boron removal from aqueous solutions has attracted increasing attention, offering benefits for animal and plant health as well as profound significance for exploiting Salt Lake boron resources. In this work, we synthesized novel glycidol-functionalized and hydrophilic polyaniline (PANI) nanorod adsorbents, which were prepared to separate boron compounds from boric acid aqueous solutions. The as-prepared adsorbents were significantly different from the traditional polymers' grafting reaction because they had a higher functional yield and more active position for adsorption. The maximum adsorption capacity (0.2210 mmoL∙g^-1) and optimal adsorption conditions (boric acid concentration of 1307 mg/L, pH = 9.82, time of 10 h) were obtained with single-factor experimentation and the response surface method (RSM). In addition, adsorption kinetics studies showed that the adsorption reaction belonged to the pseudo-first-order kinetic model, and diffusion was the key limiting factor; therefore, the adsorption equilibrium time is more than 10 h. Finally, the related possible adsorption mechanism was investigated based on the species and the diffusion of boron in the aqueous phase.

Linear and Nonlinear Regression Analysis for the Adsorption of Remazol Dye by Romanian Brewery Waste By-Product, Saccharomyces cerevisiae

Earth’s water balance and economy are becoming increasingly fragile due to overpopulation, global warming, severe environmental pollution and both surface and groundwater pollution. Therefore, it is essential to find solutions to the problems of water scarcity and water pollution. In this research, an experiment was designed to optimize the technique for the adsorption of Remazol Red F3B (RR) dye by lyophilized brewery yeast waste from the fermentation process. Moreover, we proved that brewery yeast is a great adsorbent. Batch adsorption experiments were carried out for optimization of different initial parameters, such as initial dye concentration (5–1000 mg/L), amount of yeast (0.5–2.5 g), pH (3–11) and temperature (20 to 40 °C). Furthermore, the structure and elemental composition of the adsorbent were analyzed with SEM, EDS and FTIR before and after biosorption. The best fits for the mathematical isotherm models in the case of the linear form were the Langmuir I and Freundlich models (R² = 0.923 and R² = 0.921) and, for the nonlinear form, the Khan model (R² = 0.9996) was the best fit. The pseudo-second-order kinetic model showed the best fit for both linear (plotting t/q_t vs. t) and nonlinear forms, are the calculated q_e values were similar to the experimental data.

Pyrolysis of citrus wastes for the simultaneous production of adsorbents for Cu(II), H2, and d-limonene

A route based on pyrolysis and physical activation with H₂O and CO₂ was proposed to reuse citrus waste traditionally discarded. The citrus wastes were orange peel (OP), mandarine peel (MP), rangpur lime peel (RLP), and sweet lime peel (SLP). The main aim was to use the solid products of this new route as adsorbents for Cu(II) ions. Copper ions are among the most important water pollutants due to their non-degradability, toxicity, and bioaccumulation, facilitating their inclusion and long persistence in the food chain. Besides the solid products, the liquid and gaseous fractions were evaluated for possible applications. Results showed that the citrus waste composition favored the thermochemical treatment. In addition, the following yields were obtained from the pyrolysis process: approximately 30 % wt. of biochar, 40 % wt. of non-condensable gases, and 30 % wt. of bio-oil. The biochars did not present a high specific surface area. Nevertheless, activated carbons with CO₂ and H₂O presented specific surface areas of 212.4 m²/g and 399.4 m²/g, respectively, and reached Cu(II) adsorption capacities of 28.2 mg g^-1 and 27.8 mg g^-1. The adsorption kinetic study revealed that the equilibrium was attained at 60 min and the pseudo-second-order model presented a better fit to the experimental data. The main generated gases were CO₂, which could be employed as an activating agent for activated carbon production. d-limonene, used for food and medicinal purposes, was the main constituent of the bio-oil.

Adsorbate-adsorbent potential energy function from second virial coefficient data: a non-linear Hopfield Neural Network approach

The Hopfield Neural Network has been successfully applied to solve ill-posed inverse problems in different fields of chemistry and physics. In this work, the non-linear approach for this method will be applied to retrieve the empirical parameters of potential energy function, [Formula: see text], between adsorbate and adsorbent from experimental data. Since the adsorption data is related to the second virial coefficient and therefore to [Formula: see text] through an integral equation, the Hopfield Neural Network will be used to find the best parameters which fits the experimental data. Initially simulated results will be analyzed to verify the method performance for data sets with and without noise addition. Then, experimental data for adsorption of propionitrile on activated carbon will be treated. Results presented here corroborate to the robustness of this method.

Application of 3D magnetic nanocomposites: MXene-supported Fe3O4@CS nanospheres for highly efficient adsorption and separation of dyes

Due to the presence of several hydroxyl and amino groups on the surface, chitosan (CS) has been reported to be a potential candidate to solve the pollution caused by dyes in different industrial wastewater. However, it is associated with the recycling issues. Nano-Fe₃O₄ has the advantages of easy magnetic separation and surface functionalization, which can improve the efficiency as well as selectivity of separation. However, its tendency for agglomeration can reduce the adsorption capacity. MXene can provide suitable support for both CS and Fe₃O₄ to construct new MXene@Fe₃O₄@CS composites. In this study, MXene@Fe₃O₄@CSmagnetic nanosphere was synthesized by ultrasonic self-assembly to remove Congo red (CR). Scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), and Fourier Transform Infrared (FT-IR) spectroscopy were employed to characterize the nanocomposites. According to the batch experiments, the adsorption kinetics were found to predominantly follow quasi-secondary rate kinetics. The adsorption followed Langmuir isotherm model. The adsorption process was found to be endothermic, entropy-driven, and thermodynamically spontaneous process. The adsorption capacity for CR was estimated as 620.22 mg·g^-1.

Pyrolysis of grape bagasse to produce char for Cu(II) adsorption: a circular economy perspective

Based on cleaner production and circular economy concepts, chars were produced through thermochemical conversion of grape bagasse and then used as adsorbents to uptake Cu(II) from aqueous media since Cu(II) is a common element found in fungicides to treat grapevines. The grape bagasse and char characteristics were investigated through several analytical techniques (TGA, SEM, XRD, FTIR, and BET). Three chars were obtained using different pyrolysis temperatures: 700, 800, and 900 °C. The materials had similar removal percentages and adsorption capacity. The char produced at 700 °C was chosen due to its lower production cost. Studies were conducted on the adsorbent dosage and pH effect, adsorption kinetics, isotherms, and thermodynamics. The most efficient dosage was 1.5 g L-1, and the pH was 5.5. The kinetic study showed that the equilibrium was reached in 60 min and the pseudo-second-order model presents the best fit. After the temperature influence study (25, 35, 45, and 55 °C), it was possible to verify that Cu(II) adsorption through char was favored at 55 °C. The Freundlich model showed the best fit for the experimental data. The highest removal percentage was 96.56%, and the high maximum adsorption capacity was 42 mg g-1. The thermodynamic study shows the adsorption as a spontaneous process, favorable, and endothermic.

Supplementary Information

The online version contains supplementary material available at 10.1007/s13399-022-02792-8.

Adsorption-desorption and transport behavior of pydiflumetofen in eight different types of soil

Pydiflumetofen, a fungicide of the class of succinate dehydrogenase inhibitors, can disrupt energy metabolism by inhibiting the synthesis of succinate dehydrogenase, thus effectively inhibiting pathogenic fungal growth and related yield losses.We studied the adsorption and desorption behaviors and interaction mechanisms of pydiflumetofen in eight different arable soils by the infrared spectroscopy and batch equilibrium method. Pydiflumetofen adsorption and desorption property of soils conformed with the Freundlich isotherm model and the values for the adsorption capacity KF-ads were in the range of 14.592-102.610. The adsorption constants (KF-ads) exhibited a significantly positive and linear correlation (p < 0.1) with soil organic matter and organic carbon content. Both high and low temperatures weakened the pydiflumetofen sorption capacity of the soil. In addition, the initial pH of the solution, its ionic strength, and the addition of exogenous biochar, humic acid, and different types of surfactants at different concentrations also affected the sorption property of the soil. Pydiflumetofen is weakly mobile and leachable in most soils, and, poses some threat to surface soil and water organisms, but does not contaminate groundwater.

An efficient, green and sustainable potassium hydroxide activated magnetic corn cob biochar for imidacloprid removal

The extensive use of imidacloprid (IMI) has led to its being frequently detected in natural water, also caused the potential damage to the ecosystem. Development of efficient, green and sustainable technique is demanded to eliminate this problem. A novel biochar (KMCBC) derived from agriculture waste of corn cob was first time co-modified by potassium hydroxide (KOH), ferric chloride (FeCl₃) and zinc chloride (ZnCl₂), which showed the greater adsorption amount (410 mg g^-1 at 298 K) for imidacloprid (IMI). Pseudo-second-order kinetic and Langmuir isotherm models fitted well with the experimental data, together with the physicochemical characterization analysis, demonstrating that the adsorption process of IMI by KMCBC might be mainly controlled by micropore filling, π-π electron donor-acceptor and functional groups interactions (H-bonding and complexation). Additionally, the thermodynamics parameters suggested that IMI adsorption in this study was a spontaneous, endothermic and randomly increasing process. Besides, KMCBC owned the easy separation performance and promising environmental safety, also exhibited a high selective adsorption capacity regardless of solution pH (its optimum adsorption performance for IMI was obtained at pH = 5), inorganic ions strength and humic acid (HA) concentrations. The regenerated KMCBC (synergistic ultrasound/ethanol) could sustainably and efficiently adsorb IMI in the reuse cycles. Therefore, this study provided an efficient, green and sustainable adsorbent of KMCBC for IMI removal.