Ketoprofen and aspirin removal by laccase immobilized on date stones

Effect of bamboo biochar preparation conditions on immobilization of laccase and its application

In this paper, bamboo biochar was prepared and used for laccase immobilization. Biochar was prepared under different conditions (pyrolysis temperature, heating rate and dwell time) to understand biochar characteristics impacts on enzyme activity. The results showed that the preparation conditions had an important effect on the content of carboxyl groups on biochar. And the specific surface area is not the key factor affecting laccase immobilization in this study, which is a little different than before. The highest immobilized laccase activity (1404.17 U/g) was obtained when the biochar was heated to 300 °C at the rate of 15 °C/min and stayed for 1.5 h, and the carboxy group concentration was 0.490 mmol/g. Compared with free laccase (FL), the immobilized laccase on bamboo biochar (LBC) showed higher thermo-tolerant performance, more excellent acid-proof ability and reusability. Without any mediators, LBC displayed high degradation efficiency (74.72 %, 85.88 % and 94.53 %, respectively) for bisphenol A (BPA), malachite green (MG) and methyl orange (MO) in water. Our research demonstrates that the content of carboxyl group in biochar plays a decisive role in the immobilization of laccase and LBC has excellent performance in the effective removal of toxicant in water, which makes it a promising candidate for environmental recovery.

Laccase-based biocatalytic systems application in sustainable degradation of pharmaceutically active contaminants

The outflow of pharmaceutically active chemicals (PhACs) exerts a negative impact on biological systems even at extremely low concentrations. For instance, enormous threats to human and aquatic species have resulted from the widespread use of antibiotics in ecosystems, which stimulate the emergence and formation of antibiotic-resistant bacterial species and associated genes. Additionally, it is challenging to eliminate these PhACs by employing conventional physicochemical water treatment techniques. Enzymatic approaches, including laccase, have been identified as a promising alternative to eliminate a broad array of PhACs from water matrices. However, their application in environmental bioremediation is hindered by several factors, including the enzyme's stability and its location in the aqueous environment. Such obstacles may be surmounted by employing laccase immobilization, which enables enhanced stability (including inactivation caused by the substrate), and thus improved catalysis. This review emphasizes the potential hazards of PhACs to aquatic organisms within the detection concentration range of ngL-1 to µgL-1, as well as the deployment of laccase-based multifunctional biocatalytic systems for the environmentally friendly mitigation of anticancer drugs, analgesics/NSAIDs, antibiotics, antiepileptic agents, and beta blockers as micropollutants. This approach could reduce the underlying toxicological consequences. In addition, current developments, potential applications, and viewpoints have focused on computer-assisted investigations of laccase-PhACs binding at enzyme cavities and degradability prediction.

Laccase: A Green Biocatalyst Offers Immense Potential for Food Industrial and Biotechnological Applications

Laccase, a multipurpose biocatalyst, is widely distributed across all kingdoms of life and plays a key role in essential biological processes such as lignin synthesis, degradation, and pigment formation. These functions are critical for fungal growth, plant-pathogen interactions, and maintenance of soil health. Due to its broad substrate specificity, multifunctional nature, and environmentally friendly characteristics, laccase is widely employed as a catalyst in various green chemistry initiatives. With its ability to oxidize a diverse range of phenolic and nonphenolic compounds, laccase has also been found to be useful as a food additive and for assessing food quality parameters. Ongoing advancements in research and technology are continually expanding the recognition of laccase's potential to address global environmental, health, and energy challenges. This review aims to provide critical insights into the applications of laccases in the biotechnology and food industry.

Enhanced pollutant degradation via green-synthesized core-shell mesoporous Si@Fe magnetic nanoparticles immobilized with metagenomic laccase

With rapid industrial expansion, environmental pollution from emerging contaminants has increased, posing severe ecosystem threats. Laccases offer an eco-friendly solution for degrading hazardous substances, but their use as free-form biocatalysts face challenges. This study immobilized laccase (PersiLac1) on green-synthesized Si@Fe nanoparticles (MSFM NPs) to remove pollutants like Malachite Green-containing wastewater and degrade plastic films. Characterization techniques (FTIR, VSM, XRD, SEM, EDS, BET) confirmed the properties and structure of MSFM NPs, revealing a surface area of 31.297 m2.g-1 and a pore diameter of 12.267 nm. The immobilized PersiLac1 showed enhanced activity across various temperatures and pH levels, retaining over 82 % activity after 15 cycles at 80°C with minimal leaching. It demonstrated higher stability, half-life, and decimal reduction time than free laccase. Under 1 M NaCl, its activity was 1.8 times higher than the non-immobilized enzyme. The immobilized laccase removed 98.11 % of Malachite Green-containing wastewater and retained 82.92 % activity over twenty cycles of dye removal. Additionally, FTIR and SEM confirmed superior plastic degradation under saline conditions. These findings suggest that immobilizing PersiLac1 on magnetic nanoparticles enhances its function and potential for contaminant removal. Future research should focus on scalable, cost-effective laccase immobilization methods for large-scale environmental applications.

A novel two stages chemical activation of pinewood waste for removing organic micropollutants from water and wastewater

The prevalent presence of pharmaceuticals in aquatic ecosystems underscores the necessity for developing cost-effective techniques to remove them from water. The utilization of affordable precursors in producing activated carbon, capable of rivaling commercial alternatives, remains a persistent challenge. The adsorption of diclofenac and ciprofloxacin onto a novel pinewood-derived activated carbon (FPWAC) was explored, employing a sequential activation process involving ammonium nitrate (NH4NO3) treatment followed by sodium hydroxide (NaOH) activation. The produced FPWAC was then thoroughly characterized by employing several techniques. The removal of diclofenac and ciprofloxacin in water and real wastewater effluent was examined in batch tests. The optimum removal conditions were an FPWAC dosage of 1 g L-1, pH 6, mixture concentration of 25 mg L-1, and a temperature of 25 °C. The FPWAC was able to remove both pharmaceuticals for up to six cycles, with more than 95% removal for water and 90% for wastewater in the first cycle. The adsorption performance fitted well with the non-linear Freundlich isotherm for both pollutants. The kinetics of adsorption of diclofenac followed a pseudo-first-order model, while ciprofloxacin showed adherence to the pseudo-second-order model. FPWAC proved its potency as a low-cost adsorbent for pharmaceutical removal from wastewater.

Degradation Characteristics of Nicosulfuron in Water and Soil by MnO2 Nano-Immobilized Laccase

As a typical sulfonylurea herbicide, nicosulfuron is mainly used to control grass weeds and some broadleaf weeds in corn fields. However, as the amount of use continues to increase, it accumulates in the environment and eventually becomes harmful to the ecosystem. In the present study, a new metallic nanomaterial, δ-MnO2, was prepared, which not only has a similar catalytic mechanism as laccase but also has a significant effect on pesticide degradation. Therefore, the bicatalytic property of MnO2 can be utilized to improve the remediation of nicosulfuron contamination. Firstly, MnO2 nanomaterials were prepared by controlling the hydrothermal reaction conditions, and immobilized laccase was prepared by the adsorption method. Next, we investigate the effects of different influencing factors on the effect of immobilized laccase, MnO2, and free laccase on the degradation of nicosulfuron in water and soil. In addition, we also analyze the metabolic pathway of nicosulfuron degradation in immobilized laccase and the bicatalytic mechanism of MnO2. The results demonstrated that the degradation rate of nicosulfuron in water by immobilized laccase was 88.7%, and the optimal conditions were 50 mg/L, 25 h, 50 °C, and pH 5. For nicosulfuron in soil, the optimal conditions for the degradation by immobilized laccase were found to be 151.1 mg/kg, 46 °C, and pH 5.9; under these conditions, a degradation rate of 90.1% was attained. The findings of this study provide a theoretical reference for the immobilized laccase treatment of sulfonylurea herbicide contamination in water and soil.

Solar light driven degradation of piroxicam and paracetamol by heterogeneous photocatalytic fenton system: Process optimization, mechanistic studies and toxicity assessment

The widespread occurence of pharmaceutical pollutants seriously threatens the environment and human well-being. In the present study, zinc ferrite nanoparticles (ZnFe2O4 NPs) have been synthesized by co-precipitation method and used as photocatalyst for the degradation of two most commonly prescribed painkillers, piroxicam (PXM) and paracetamol (PCM), via heterogeneous Fenton process under the solar light. The synthesized ZnFe2O4 NPs showed a narrower band gap i.e. 1.87 eV, signifying the ability to efficiently work in visible light range. In context of photocatalytic applications, the operational conditions were optimized to achieve maximum degradation. PCM and PXM were completely degraded (100%) at the optimized photocatalytic dose (20 mg L-1), reaction time (180 min), initial drug concentration (10 mg L-1), and pH (6.0), which is close to the natural environment. The extent of mineralization as estimated by the reduction of total organic carbon (TOC) was observed to be ∼91 and 82% for PCM and PXM respectively. Kinetic studies revealed that photocatalytic degradation followed pseudo-first-order kinetics. Moreover, the ZnFe2O4 NPs retained ∼90 % of photocatalytic activity after five consecutive reaction cycles, showing remarkable reusability and stability of catalyst.

A novel and sustainable composite of L@PSAC for superior removal of pharmaceuticals from different water matrices: Production, characterization, and application

This study endeavors to develop cost-effective environmentally friendly technology for removing harmful residual pharmaceuticals from water and wastewater by utilizing the effective adsorption of pistachio shell (PS) biochar and the degradation potency of laccase immobilized on the biochar (L@PSAC). The carbonatization and activation of the shells were optimized regarding temperature, time, and NH4NO3/PS ratio. This step yielded an optimum PS biochar (PSAC) with the highest porosity and surface area treated at 700 °C for 3 h using an NH4NO3/PS ratio of 3% wt. The immobilization of laccase onto PSAC (L@PSAC) was at its best level at pH 5, 60 U/g, and 30 °C. The optimum L@PSAC maintained a high level of enzyme activity over two months. Almost a complete removal (>99%) of diclofenac, carbamazepine, and ciprofloxacin in Milli-Q (MQ) water and wastewater was achieved. Adsorption was responsible for >80% of the removal and the rest was facilitated by laccase degradation. L@PSAC maintained effective removal of pharmaceuticals of ≥60% for up to six treatment cycles underscoring the promising application of this material for wastewater treatment. These results indicate that activated carbon derived from the pistachio shell could potentially be utilized as a carrier and adsorbent to efficiently remove pharmaceutical compounds. This enzymatic physical elimination approach has the potential to be used on a large-scale.

A sustainable nano-hybrid system of laccase@M-MWCNTs for multifunctional PAHs and PhACs removal from water, wastewater, and lake water

This study examined the use of modified multiwall carbon nanotubes (M-MWCNTs) with immobilized laccase (L@M-MWCNTs) for removing ciprofloxacin (Cip), carbamazepine (Cbz), diclofenac (Dcf), benzo[a]pyrene (Bap), and anthracene (Ant) from different water samples. The synthesized materials were characterized using an array of advanced analytical techniques. The physical immobilization of laccase onto M-MWCNTs was confirmed through Scanning electron microscope (SEM)-dispersive X-ray spectroscopy (EDS) analysis and Brunner-Emmet-Teller (BET) surface area measurements. The specific surface area of M-MWCNTs decreased by 65% upon laccase immobilization. There was also an increase in nitrogen content seen by EDS analysis asserting successful immobilization. The results of Boehm titration and Fourier transform infrared (FTIR) exhibited an increase in acidic functional groups after laccase immobilization. L@M-MWCNTs storage for two months maintained 77.8%, 61.6%, and 57.6% of its initial activity for 4 °C, 25 °C, and 35 °C, respectively. In contrast, the free laccase exhibited 55.3%, 37.5%, and 23.5% of its initial activity at 4 °C, 25 °C, and 35 °C, respectively. MWCNTs improved storability and widened the working temperature range of laccase. The optimum removal conditions of studied pollutants were pH 5, 25 °C, and 1.6 g/L of M-MWCNTs. These parameters led to >90% removal of the targeted pollutants for four treatment cycles of both synthetic water and spiked lake water. L@M-MWCNTs demonstrated consistent removal of >90% for up to five cycles even with spiked wastewater. The adsorption was endothermic and followed Langmuir isotherm. Oxidation, dehydrogenation, hydroxylation, and ring cleavage seem to be the dominant degradation mechanisms.

A sustainable and highly efficient fossil-free carbon from olive stones for emerging contaminants removal from different water matrices

The olive stone is a large waste product of the olive oil extraction industry. The present study investigates developing activated carbon from olive stone waste (OSAC) to remove pharmaceuticals from water. Different temperatures and olive stone: KOH ratios were studied. The OSAC produced at 750 °C and 1:3 ratio was found to have the highest porosity and surface area and was tested in the adsorption process. Diclofenac and ciprofloxacin were selected as model contaminants. The adsorption process was optimized with regards to OSAC dosage, pH, temperature, and initial concentration of adsorbate. The OSAC was found to be effective for a wide pH range (2-11) with an optimum dosage of 1 g/L at 25 °C. The pharmaceuticals were almost completely removed in 75 min. The adsorption was endothermic and followed first-order kinetics with physical mechanisms such as electrostatic possibly being the main driver. The optimum conditions were applied to test the removal of diclofenac and ciprofloxacin in synthetic water, lake water (Lake Balaton, Hungary) and secondary wastewater for seven cycles. There was little difference between the removal of the tested water matrices highlighting the potency of OSAC as an adsorbent for pharmaceutical removal in industrial applications. The removal dropped from >99% for the first cycle to 20-30% for the seventh cycle.

A Sustainable Banana Peel Activated Carbon for Removing Pharmaceutical Pollutants from Different Waters: Production, Characterization, and Application

Due to the growing concerns about pharmaceutical contamination and its devastating impact on the economy and the health of humans and the environment, developing efficient approaches for removing such contaminants has become essential. Adsorption is a cost-effective technique for removing pollutants. Thus, in this work, banana peels as agro-industrial waste were utilized for synthesizing activated carbon for removing pharmaceuticals, namely amoxicillin and carbamazepine from different water matrices. The chemically activated carbon by phosphoric acid (H3PO4) was carbonized at temperatures 350 °C, 450 °C and 550 °C. The material was characterized by several techniques such as scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM-EDS), Fourier transform infrared spectroscopy (FTIR), Boehm titration, point of zero charge (pHPZC), BET surface area (SBET), the proximate and ultimate analyses, X-ray powder diffraction (XRD), and thermos-gravimetric analysis (TGA). The SEM of banana peel activated carbon (BPAC) depicted a semi-regular and heterogeneous morphology, characterized by an abundance of pores with diverse forms and sizes. Boehm titration revealed an increase in the amounts of acidic groups by 0.711 mmol/g due to activation by H3PO4. FTIR recorded different peaks suggesting significant modifications in the spectroscopic characteristics of the BPAC surface due to the successful activation and adsorption of the pollutant molecules. The pHpzc of BPAC was calculated to be 5.005. The SBET surface area dramatically increased to 911.59 m2/g after the activation. The optimum conditions were 25 °C, a materials dosage of 1.2 g/L, a saturation time of 120 min, a pollutants mixture of 25 mg/L, and a pH of 5. Langmuir exhibits a slightly better fit than Freundlich with a low value of the residual sum of squares (SSE) and the data were better fitted to the pseudo-second-order kinetic. Furthermore, the efficacy of BPAC in eliminating pharmaceuticals from Milli Q water, lake water, and wastewater was successfully investigated over the seven cycles. The results of the present work highlighted a potential usage of agro-industrial waste in eliminating organic micropollutants while exhibiting sustainable management of this waste.

Laccases as Effective Tools in the Removal of Pharmaceutical Products from Aquatic Systems

This review aims to provide a comprehensive overview of the application of bacterial and fungal laccases for the removal of pharmaceuticals from the environment. Laccases were evaluated for their efficacy in degrading pharmaceutical substances across various categories, including analgesics, antibiotics, antiepileptics, antirheumatic drugs, cytostatics, hormones, anxiolytics, and sympatholytics. The capability of laccases to degrade or biotransform these drugs was found to be dependent on their structural characteristics. The formation of di-, oligo- and polymers of the parent compound has been observed using the laccase mediator system (LMS), which is advantageous in terms of their removal via commonly used processes in wastewater treatment plants (WWTPs). Notably, certain pharmaceuticals such as tetracycline antibiotics or estrogen hormones exhibited degradation or even mineralization when subjected to laccase treatment. Employing enzyme pretreatment mitigated the toxic effects of degradation products compared to the parent drug. However, when utilizing the LMS, careful mediator selection is essential to prevent potential increases in environment toxicity. Laccases demonstrate efficiency in pharmaceutical removal within WWTPs, operating efficiently under WWTP conditions without necessitating isolation.

Cultivation of blue green algae (Arthrospira platensis Gomont, 1892) in wastewater for biodiesel production

The production of biodiesel has become an important issue in the effort to reduce gas emissions due to the climate change crisis; therefore, algae have widely used to produce biodiesel for energy sustainability. The present study represented an effort to assess the ability of the alga Arthrospira platensis to produce fatty acids involved in biofuel (diesel) by cultivation in Zarrouk media enriched with different municipal wastewater concentrations. Wastewater was used in different concentrations (5, 15, 25, 35 and 100% [control]). Five fatty acids from the alga were determined and included in the present study. These were inoleic acid, palmitic acid, oleic acid, gamma-linolenic acid, and docosahexaenoic acid. Impact of different cultivation conditions were studied in terms of observed changes in growth rate, doubling time, total carbohydrate, total protein, chlorophyll a, carotenoids, phycocyanin, allophycocyanin, and phycobiliproteins. Results showed an increase in the values of growth rate, total protein content, chlorophyll a, and levels of carotenoids at all treatments except for carbohydrate content, which decreased with an increasing concentration of wastewater. The high value of doubling time (11.605 days) was recorded at treatment 5%. Fatty acids yields were increased at treatment 5% and 15%. The highest concentrations of fatty acids were 3.108 mg/g for oleic acid, gamma-linolenic acid (28.401 mg/g), docosahexaenoic acid (41.707 mg/g), palmitic acid (1.305 mg/g), and linoleic acid (0.296 mg/g). Moreover, the range of phycocyanin (0.017-0.084 mg/l), allophycocyanin (0.023-0.095 mg/l), and phycobiliproteins (0.041-0.180 mg/l) were obtained in treatment with 15-100%, respectively. Cultivation with municipal wastewater reduced the values of nitrate, phosphate, and electrical conductivity as well as increased dissolved oxygen. Maximum electrical conductivity was recorded in untreated wastewater with algae, while the highest level of dissolved oxygen was noted at 35% concentration. The use of the household wastewater is more environmentally friendly as an alternative of the traditional cultivation techniques used for long-term for biofuel production.

Ketoprofen as an emerging contaminant: occurrence, ecotoxicity and (bio)removal

Ketoprofen, a bicyclic non-steroidal anti-inflammatory drug commonly used in human and veterinary medicine, has recently been cited as an environmental contaminant that raises concerns for ecological well-being. It poses a growing threat due to its racemic mixture, enantiomers, and transformation products, which have ecotoxicological effects on various organisms, including invertebrates, vertebrates, plants, and microorganisms. Furthermore, ketoprofen is bioaccumulated and biomagnified throughout the food chain, threatening the ecosystem function. Surprisingly, despite these concerns, ketoprofen is not currently considered a priority substance. While targeted eco-pharmacovigilance for ketoprofen has been proposed, data on ketoprofen as a pharmaceutical contaminant are limited and incomplete. This review aims to provide a comprehensive summary of the most recent findings (from 2017 to March 2023) regarding the global distribution of ketoprofen in the environment, its ecotoxicity towards aquatic animals and plants, and available removal methods. Special emphasis is placed on understanding how ketoprofen affects microorganisms that play a pivotal role in Earth's ecosystems. The review broadly covers various approaches to ketoprofen biodegradation, including whole-cell fungal and bacterial systems as well as enzyme biocatalysts. Additionally, it explores the potential of adsorption by algae and phytoremediation for removing ketoprofen. This review will be of interest to a wide range of readers, including ecologists, microbiologists, policymakers, and those concerned about pharmaceutical pollution.

Improved methylene blue adsorption from an aqueous medium by ozone-triethylenetetramine modification of sawdust-based biochar

In this study, sawdust biochar-O3-TETA (SDBT), a novel biochar, was prepared via treatment with 80% sulfuric acid, followed by oxidation by ozone and subsequent treatment with boiling Triethylenetetramine (TETA). Characterization studies of the prepared SDBT adsorbent were performed with SEM-EDX, BET, XRD, BJH, FT-IR, DTA and TGA analyses. The adsorption efficiency of MB dye by SDBT biochar from water was investigated. Methylene Blue (MB) dye absorption was most effective when the solution pH was 12. The maximum removal % of MB dye was 99.75% using 20 mg/L as starting MB dye concentration and 2.0 g/L SDBT dose. The Qm of the SDBT was 568.16 mg/g. Actual results were fitted to Temkin (TIM), Freundlich (FIM), and Langmuir (LIM) isotherm models. The experimental results for SDBT fitted well with all three models. Error function equations were used to test the results obtained from these isotherm models, which showed that the experimental results fit better with TIM and FIM. Kinetic data were investigated, and the pseudo-second-order (PSOM) had R2 > 0.99 and was mainly responsible for guiding the absorption rate. The removal mechanism of the MB dye ions in a base medium (pH 12) may be achieved via physical interaction due to electrostatic interaction between the SDBT surface and the positive charge of the MB dye. The results show that SDBT effectively removes the MB dye from the aqueous environment and can be used continually without losing its absorption efficiency.

Efficient removal of pharmaceutical contaminants from water and wastewater using immobilized laccase on activated carbon derived from pomegranate peels

In this study, pomegranate peels (PPs) as an abundant fruit processing waste was used to produce cost-effective, eco-friendly, and high-quality activated carbon. The produced carbon (fossil free activated carbon) was used for immobilizing laccase to remove a range of emerging pollutants namely diclofenac, amoxicillin, carbamazepine, and ciprofloxacin from water and wastewater. The loaded activated carbon by laccase (LMPPs) and the unloaded one (MPPs) were characterized using advanced surface chemistry analysis techniques. MPPs was found to have a porous structure with a large surface area and an abundance of acidic functional groups. Laccase immobilization reduced surface area but added active degradation sites. The optimal immobilization parameters were determined as pH 4, 35 °C, and a laccase concentration of 2.5 mg/mL resulting in a 69.8% immobilization yield. The adsorption of the emerging pollutant onto MPPs is best characterized as a spontaneous endothermic process that adheres to the Langmuir isotherm and first-order kinetics. Using synergistic adsorption and enzymatic degradation, the target pollutants (50 mg/L) were eliminated in 2 h. In both water types, LMPPs outperformed MPPs. This study shows that pomegranate peels can effectively be harnessed as an enzyme carrier and adsorbent for the removal of emerging pollutants even from a complex sample matrix. The removal of contaminants from wastewater lasted five cycles, whereas it continued up to six cycles for water.

Design of a 3D Amino-Functionalized Rice Husk Ash Nano-Silica/Chitosan/Alginate Composite as Support for Laccase Immobilization

Recycling of agro-industrial waste is one of the major issues addressed in recent years aimed at obtaining products with high added value as a future alternative to traditional ones in the per-spective of a bio-based and circular economy. One of the most produced wastes is rice husk and it is particularly interesting because it is very rich in silica, a material with a high intrinsic value. In the present study, a method to extract silica from rice husk ash (RHA) and to use it as a carrier for the immobilization of laccase from Trametes versicolor was developed. The obtained mesoporous nano-silica was characterized by X-ray diffraction (XRD), ATR-FTIR spectroscopy, Scanning Elec-tron Microscopy (SEM), and Energy Dispersive X-ray spectroscopy (EDS). A nano-silica purity of about 100% was found. Nano-silica was then introduced in a cross-linked chitosan/alginate scaffold to make it more easily recoverable after reuse. To favor laccase immobilization into the composite scaffold, functionalization of the nano-silica with (γ-aminopropyl) triethoxysilane (APTES) was performed. The APTES/RHA nano-silica/chitosan/alginate (ARCA) composite al-lowed to obtain under mild conditions (pH 7, room temperature, 1.5 h reaction time) a robust and easily reusable solid biocatalyst with 3.8 U/g of immobilized enzyme which maintained 50% of its activity after six reuses. The biocatalytic system, tested for syringic acid bioremediation, was able to totally oxidize the contaminant in 24 h.

Hierarchically-structured laccase@Ni3(PO4)2 hybrid nanoflowers for antibiotic degradation: Application in real wastewater effluent and toxicity evaluation

Laccase@Ni₃(PO₄)₂ hybrid nanoflowers (HNFs) were prepared by the anisotropic growth of biomineralized nickel phosphate. The immobilization yield was 77.5 ± 3.6 %, and the immobilized enzyme retained 50 % of its initial activity after 18 reusability cycles. The immobilized and free enzymes lost 80 % of their activity after 18 and 6 h incubation in municipal wastewater effluent (MWWE), respectively. The increase in α-helix content (8 %) following immobilization led to a more rigid enzyme structure, potentially contributing to its improved stability. The removal of ciprofloxacin from MWWE by laccase@Ni₃(PO₄)₂·HNFs/p-coumaric acid oxidation system was optimized using a Box-Behnken design. Under the optimized conditions [initial laccase activity (0.05 U mL^-1), the concentration of p-coumaric acid (2.9 mM), and treatment time (4.9 h)], the biocatalyst removed 90 % of ciprofloxacin (10 mg L^-1) from MWWE. The toxicity of ciprofloxacin against some G⁺ and G^- bacteria was reduced by 35-70 %, depending on their strain. The EC₅₀ of ciprofloxacin for the alga Raphidocelis subcapitata reduced from 3.08 to 1.07 mg L^-1 (p-value <0.05) after the bioremoval. Also, the acute and chronic toxicity of identified biodegradation products was lower than ciprofloxacin at three trophic levels, as predicted by ECOSAR software.