Vortex-assisted micro-solid-phase extraction followed by low-density solvent based dispersive liquid–liquid microextraction for the fast and efficient determination of phthalate esters in river water samples

Recoverable and reusable light-induced multi-arm azobenzenes-Fe3O4 hybrid sorbent for enrichment of phthalate plasticizer and utilized as a SALDI substrate for the detection of 2-naphthol

The construction, structural identifications along with compositional properties, using TEM, FT-IR, and XPS spectroscopies, of an innovative light-induced multi-arm azobenzenes based Fe3O4 magnetic nanoparticles (Azo-Fe3O4 MNPs) are being reported. Such organic (light-sensitive dendrimers-like structure), inorganic (magnet core), hybrid material has been applied as an efficient recoverable/reusable extractive sorbent for the detection of phthalate plasticizers from acetate buffer solution. The extraction study was controlled within consecutive procedures via UV-light exposure to achieve pore-size control which then further subjected for the evaluation of the analytes' retention, separation, and release as well as the detection of the phthalate pollutants using GCMS-. Various experimental conditions, such as time of extraction, salt concentration, pH, and desorption time, were studied and adjusted. Additionally, the extraction repeatability (RSD from 0.46 % to 6.12%, n = 5) of the studied sorbent was comparable to other published work. The linear range extended from 6.25 to 100 μg L-¹ and detection limits (LOD) within the range of 41- 150 ng L-1 were achieved, demonstrating good linearity with values ranging from 0.9992 to 0.9892. The inter-batch and intra-batch RSD ranged from 0.46 % to 6.12 %, respectively. Additionally, it provides effective detection of 2-naphthol when used as a SALDI substrate.

A heteropore covalent organic framework for highly selective enrichment of aryl-organophosphate esters in environmental water coupled with UHPLC-MS/MS determination

The identification of an increasing number of aryl organophosphate esters (aryl-OPEs) in environmental samples has led to growing attention recently. Due to the potential adverse effects on human health and environment, development of new analytical methods for sensitive and selective determination of aryl-OPEs in complex matrices is urgently needed. Here, a novel analytical method for the identification and determination of trace amounts of aryl-OPEs in water samples is developed by using melamine sponge@heteropore covalent organic framework (MS@HCOF) based on vortex-assisted extraction (VAE) prior to UHPLC-MS/MS analysis. The MS@HCOF was rationally designed and synthesized through an in-situ growth strategy and exhibited superior selectivity toward aryl-OPEs compared with that of MS@single-pore COF (MS@SCOF) due to steric effect. A systematic optimization was conducted on important parameters of VAE, resulting in the successful extraction of nine aryl-OPEs in just 6 min. Under optimized conditions, the limits of detection (S/N = 3) and quantification (S/N = 10) were within the ranges of 0.001-0.027 and 0.005-0.091 ng/L for nine aryl-OPEs, respectively. The validated method was proven applicable to real water samples, i.e., the recoveries were 65.3-119.5 % for seawater, 59.4-112.9 % for effluent, and 76.0-117.4 % for tap water. Furthermore, the adsorption mechanisms were explored through density functional theory (DFT) calculations. DFT results revealed that a notable selective enrichment capacity of MS@HCOF towards aryl-OPEs stems from π-π conjugation and hydrogen bonding. The established method benefits from the advantages of high selectivity and sensitivity for the ultra-trace determination of aryl-OPEs.

A global meta-analysis of phthalate esters in drinking water sources and associated health risks

Phthalate esters (PAEs) are known as esters of phthalic acid, which are commonly used as plasticizers in the plastic industry. Due to the lack of chemical bonding with the polymer matrix, these compounds are easily separated from plastic products and enter the environment. To investigate the growth of concentration of PAEs like DBP (Dibutyl phthalate), DEP (Diethyl phthalate), DMP (Dimethyl phthalate), DIBP (Diisobutyl phthalate), and TPMBP (tris(2-methylbutyl) phosphate) in different water sources, a study from January 01, 1976, to April 30, 2021, was implemented via a global systematic review plus meta-analysis in which, 109 articles comprising 4061 samples, 4 water types, and 27 countries were included. Between various types of water sources, river water and lake water were the most contaminated resources with PAEs. Among all studies of PAEs, DBP and DEP with the values >15,573 mg L-1 have the highest average concentration and TPMBP with the value 0.002885 mg L-1 has the lowest average concentration in water sources. The most contaminated water sources with PAEs were in Nigeria and the least contaminated was in China. Besides, Monte-Carlo simulation indicated that for DMP and DEP minimum values that are lower than the acceptable limit are generated. However, most of the population (>75 %) is at risk for both adults and child cases. For DIBP and DBP the situation is much worse, the simulations not providing at least one case where the R index is lower than the acceptable limit of 1E-06.

Vortex-assisted dispersive liquid-phase microextraction for the analysis of main active compounds from Zi-Cao-Cheng-Qi decoction based on a hydrophobic deep eutectic solvent

In this study, a vortex-assisted hydrophobic deep eutectic solvent dispersive liquid-phase microextraction was developed and used for the extraction and preconcentration of six main active compounds in Zi-Cao-Cheng-Qi decoction. The deep eutectic solvent, prepared by mixing tetrabutylammonium chloride and hexanoic acid at a molar ratio of 1:1, was added to the sample solution containing the analytes. In the absence of disperser, the extractant was rapidly dispersed into fine droplets by the aid of vortex and adequately contacted with the analytes. Some key parameters affecting the approach including extraction solvent type and volume, sample phase pH, extraction time, centrifugation time, and salt concentration were investigated and optimized. Under the optimum conditions, enrichment factors of the target analytes were in the range of 3-330. The calibration graphs were linear with a correlation coefficient (r) ≥ 0.9929. The detection limits were 0.3-0.9 ng/mL, and the satisfactory precisions (relative standard deviations, 0.5-8.9%) and accuracies (relative recoveries, 91.1-102.2%) were also obtained. The developed method was rapid (only 2 min), eco-friendly, effective, and easy to operate. And it has been successfully applied to simultaneous extraction, enrichment, and determination of the main active compounds in a traditional Chinese medicinal formula coupled with high-performance liquid chromatography.

Enhanced microextraction of endocrine disrupting chemicals adsorbed on airborne fine particulate matter with gas chromatography-tandem mass spectrometric analysis

A novel double-microextraction approach, combining dispersive liquid-liquid microextraction (DLLME) and vortex-assisted micro-solid-phase extraction (VA-µ-SPE) was developed. The procedure was applied to extract endocrine disrupting chemicals (EDCs) consisting of three phthalate esters (PEs) and bisphenol A (BPA) associated with PM_2.5 (airborne particulate matter with aerodynamic diameter ≤ 2.5 µm). Gas chromatography-tandem mass spectrometry (GC-MS/MS) was used for determination of the analytes. These analytes were first ultrasonically desorbed from PM_2.5 in a 10% acetone aqueous solution. DLLME was used to first preconcentrate the analytes; the sample solution, still in the same vial, was then subjected to VA-µ-SPE. The synergistic effects provided by the combination of the microextraction techniques provided advantages such as high enrichment factors and good cleanup performance. Various extraction parameters such as type and volume of extractant solvent (for DLLME), and type of sorbent, extraction time, desorption solvent, volume of desorption solvent and desorption time (for µ-SPE) were evaluated. Multi-walled carbon nanotubes were found to be the most suitable sorbent. This procedure achieved good precision with intra- and inter-day relative standard deviations of between 1.93 and 9.95%. Good linearity ranges (0.3-100 ng/mL and 0.5-100 ng/mL, depending on analytes), and limits of detection (LODs) of between 0.07 and 0.15 ng/mL were obtained. The method was used to determine the levels of PEs and BPA in ambient air, with concentrations ranging between below the limits of quantification and 0.48 ng/m³. DLLME-VA-µ-SPE-GC-MS/MS was demonstrated to be suitable for the determination of these EDCs present in PM_2.5.

Fabrication of UMCM-1 based monolithic and hollow fiber - Metal-organic framework deep eutectic solvents/molecularly imprinted polymers and their use in solid phase microextraction of phthalate esters in yogurt, water and edible oil by GC-FID

In this study, for the first time, hollow fiber and monolithic fiber were fabricated based on metal-organic framework deep eutectic solvents/molecularly imprinted polymers (MOF- DES/MIPs) and were used for microextraction of phthalate esters under termed hollow fiber liquid membrane-protected solid-phase microextraction (HFLMP-SPME) followed by gas chromatography- flame ionization detection. Several parameters influencing extraction recoveries of phthalate esters including adsorption and desorption parameters were investigated and optimized using fabricated MOF- DES/MIPs monolithic fiber. Under optimal conditions, detection limits (S/N = 3) of the method were in a range of 0.008-0.03 µg L^-1 and limits of quantification (S/N = 10) were between 0.028 and 0.12 µg L^-1. RSD (%) for intra-day and inter-day precisions were between 2.4-4.7% and 2.6-3.4%, respectively. Subsequently, this procedure was successfully applied with satisfactory results in the determination of phthalate esters in yogurt, water, and soybean oil samples. The R (%) ranged from 95.5 to 100.0% in different samples.

Core-shell structured magnetic mesoporous carbon nanospheres derived from metal-polyphenol coordination polymer-coated Fe3 O4 and its application in the enrichment of phthalates from water samples

In this work, core-shell structured magnetic mesoporous carbon nanospheres were fabricated from the carbonization of metal-polyphenol coordination polymer-coated Fe₃ O₄ nanoparticles. The preparation method is simple, fast, versatile, and easy to scale up. Magnetic mesoporous carbon nanospheres exhibit a high specific surface area, high superparamagnetism, and high adsorption efficiencies for phthalates. Four phthalates were extracted from aqueous solutions by using magnetic mesoporous carbon nanospheres via magnetic solid phase extraction. Subsequent analysis was performed by using high-performance liquid chromatography with ultraviolet detection. The analytical method has good linearity in the concentration range of 1-200 ng/mL for diethyl phthalate, diisobutyl phthalate, and dicyclohexyl phthalate, and 3-200 ng/mL for dipropyl phthalate. The limits of detection were in the range of 0.10-0.62 ng/mL. Compared with previous methods, this method has a lower detection limit, wider linearity range, and faster adsorption and desorption rates. The results indicate that magnetic mesoporous carbon nanospheres are suitable for the enrichment of hydrophobic substances from aqueous solutions.

C8-modified magnetic graphene oxide based solid-phase extraction coupled with dispersive liquid-liquid microextraction for detection of trace phthalate acid esters in water samples

Phthalate acid esters (PAEs) are extensively applied in plastic and plastic products, and have caused potential hazards on human and animal health. In this study, a highly sensitive method was proposed for trace detection of selected PAEs in water by gas chromatography-mass spectrometry, after solid-phase extraction (SPE) using octyl (C8)-modified magnetic graphene oxide (MGO-C8) as the adsorbent followed by dispersive liquid-liquid microextraction (DLLME). The prepared MGO-C8 was characterized by Fourier transform infrared spectroscopy (FT-IR), thermo gravimetric analysis (TGA) and vibrating sample magnetometry (VSM). The recoveries of the PAEs using MGO-C8 as the adsorbent were found to be significantly higher those obtained by MGO. The influences of solution pH, adsorption and desorption time, eluent and extractant, and salt addition on the extraction efficiency of PAEs were investigated. Under the optimized conditions, limits of detection (LODs) of 0.5-1.0 ng L^-1 for PAEs, and related standard deviations (RSDs) of 4.8-7.5% were obtained. The proposed method was utilized in the detection of trace PAEs in real environmental water samples, with spiked recoveries of 89.5-112.3%, 91.5-105.0% and 98.0-110.0% for DBP, DEHP and DNOP, respectively.

Determination of phthalate esters in seawater of Chabahar Bay using dispersive liquid-liquid microextraction coupled with GC-FID

Phthalate esters (PEs), a group of environmental pollutants which are possibly carcinogenic to humans, have been detected in seawater. Seven PEs in seawater were quantitatively determined by using gas-chromatography flame ionizing detection after executing dispersive liquid-liquid microextraction. The suggested method is optimized for microextraction and determination of PEs in artificial sea water. Factors affecting the microextraction procedure such as the type and volume of extracting and dispersive solvents (carbon tetrachloride, 20 μL; methanol, 0.5 mL), extraction time and pH (7) were investigated. Under optimum conditions, the limit of detection of the analytes were obtained between 0.04 and 4.52 μg·L^-1, and linearity and linear range were of 0.999 ≥ R² ≥ 0.994 and 10-560 μg·L^-1 respectively. Enrichment factors were found in the range of 761-827 fold, while the relative standard deviations of the analytes were between 0.17 and 7.5% (n = 6) for real sea water samples. Using this method, total PEs content of seawater from several locations in Chabahar Bay (the southeast part of Iran) was estimated 2.33-90.45 μg·L^-1.

Porous membrane protected micro-solid-phase extraction: A review of features, advancements and applications

Membrane protected micro-solid-phase extraction (μ-SPE) was introduced in 2006 as an alternative to multistep SPE. μ-SPE is based on packing of very small amount of sorbent inside the porous membrane sheet whose edges are heat sealed to fabricate a μ-SPE device. This device performs clean up, extraction, and pre-concentration in a single step. It suits best for extraction of complex samples as sorbent is effectively protected inside the membrane and extraneous matter cannot adsorb over it. This review summarizes most important aspects of μ-SPE including basic principles, extraction procedure, different formats, sorbents employed and affecting parameters. The article also provides a brief account on modified μ-SPE procedures where μ-SPE was either combined with other techniques or some major changes were introduced in original procedure. Finally, the applications of μ-SPE in environmental, food and biological analysis are described. At the end, advantages and pitfalls of μ-SPE are critically appraised.

Ultrasound assisted extraction combined with dispersive liquid-liquid microextraction (US-DLLME)-a fast new approach to measure phthalate metabolites in nails

A new, fast, and environmentally friendly method based on ultrasound assisted extraction combined with dispersive liquid-liquid microextraction (US-DLLME) was developed and optimized for assessing the levels of seven phthalate metabolites (including the mono(ethyl hexyl) phthalate (MEHP), mono(2-ethyl-5-hydroxyhexyl) phthalate (5-OH-MEHP), mono(2-ethyl-5-oxohexyl) phthalate (5-oxo-MEHP), mono-n-butyl phthalate (MnBP), mono-isobutyl phthalate (MiBP), monoethyl phthalate (MEP), and mono-benzyl phthalate (MBzP)) in human nails by UPLC-MS/MS. The optimization of the US-DLLME method was performed using a Taguchi combinatorial design (L9 array). Several parameters such as extraction solvent, solvent volume, extraction time, acid, acid concentration, and vortex time were studied. The optimal extraction conditions achieved were 180 μL of trichloroethylene (extraction solvent), 2 mL trifluoroacetic acid in methanol (2 M), 2 h extraction and 3 min vortex time. The optimized method had a good precision (6-17 %). The accuracy ranged from 79 to 108 % and the limit of method quantification (LOQm) was below 14 ng/g for all compounds. The developed US-DLLME method was applied to determine the target metabolites in 10 Belgian individuals. Levels of the analytes measured in nails ranged between <12 and 7982 ng/g. The MEHP, MBP isomers, and MEP were the major metabolites and detected in every sample. Miniaturization (low volumes of organic solvents used), low costs, speed, and simplicity are the main advantages of this US-DLLME based method. Graphical Abstract Extraction and phase separation of the US-DLLME procedure.

Simple and accurate measurement of carbamazepine in surface water by use of porous membrane-protected micro-solid-phase extraction coupled with isotope dilution mass spectrometry

To achieve fast and accurate analysis of carbamazepine in surface water, we developed a novel porous membrane-protected micro-solid-phase extraction (μ-SPE) method, followed by liquid chromatography-isotope dilution tandem mass spectrometry (LC-IDMS/MS) analysis. The μ-SPE device (∼0.8 × 1 cm) was fabricated by heat-sealing edges of a polypropylene membrane sheet to devise a bag enclosing the sorbent. The analytes (both carbamazepine and isotope-labelled carbamazepine) were first extracted by μ-SPE device in the sample (10 mL) via agitation, then desorbed in an organic solvent (1 mL) via ultrasonication. Several parameters such as organic solvent for pre-conditioning of μ-SPE device, amount of sorbent, adsorption time, and desorption solvent and time were investigated to optimize the μ-SPE efficiency. The optimized method has limits of detection and quantitation estimated to be 0.5 ng L(-1) and 1.6 ng L(-1), respectively. Surface water samples spiked with different amounts of carbamazepine (close to 20, 500, and 1600 ng L(-1), respectively) were analysed for the validation of method precision and accuracy. Good precision was obtained as demonstrated by relative standard deviations of 0.7% for the samples with concentrations of 500 and 1600 ng kg(-1), and 5.8% for the sample with concentration of 20 ng kg(-1). Good accuracy was also demonstrated by the relative recoveries in the range of 96.7%-103.5% for all samples with uncertainties of 1.1%-5.4%. Owing to the same chemical properties of carbamazepine and isotope-labelled carbamazepine, the isotope ratio in the μ-SPE procedure was accurately controlled. The use of μ-SPE coupled with IDMS analysis significantly facilitated the fast and accurate measurement of carbamazepine in surface water.

Estimation of the presence of unmetabolized dialkyl phthalates in untreated human urine by an on-line miniaturized reliable method

At present, human exposure to dialkyl phthalates is assessed through urinary measurement of their metabolites due mainly to contamination in their analysis by their ubiquitous presence. An on-line miniaturized method and the processing of the untreated urine samples have been the key factors for minimizing contamination and achieving unbiased results. Di(2-ethylhexyl) (DEHP), diethyl (DEP), dibutyl (DBP) and mono-ethylhexyl (MEHP) phthalates in urine samples have been included in the study; MEHP as metabolite of the main dialkyl phthalate such as DEHP. On-line in-tube solid-phase microextraction (IT-SPME)-capillary liquid chromatography (CapLC) with diode array detection (DAD) is employed. The detection limits (LODs) achieved in urine were between 0.5 and 1.5 μg/L. Eighteen urines were processed. DBP and DEHP were found in nine and five samples, respectively and DEP in three of them. MEHP was only detected in one of the eighteen samples analyzed.

Reliable quantification of phthalates in environmental matrices (air, water, sludge, sediment and soil): a review

Because of their widespread application, phthalates or phthalic acid esters (PAEs) are ubiquitous in the environment. Their presence has attracted considerable attention due to their potential impacts on ecosystem functioning and on public health, so their quantification has become a necessity. Various extraction procedures as well as gas/liquid chromatography and mass spectrometry detection techniques are found as suitable for reliable detection of such compounds. However, PAEs are ubiquitous in the laboratory environment including ambient air, reagents, sampling equipment, and various analytical devices, that induces difficult analysis of real samples with a low PAE background. Therefore, accurate PAE analysis in environmental matrices is a challenging task. This paper reviews the extensive literature data on the techniques for PAE quantification in natural media. Sampling, sample extraction/pretreatment and detection for quantifying PAEs in different environmental matrices (air, water, sludge, sediment and soil) have been reviewed and compared. The concept of "green analytical chemistry" for PAE determination is also discussed. Moreover useful information about the material preparation and the procedures of quality control and quality assurance are presented to overcome the problem of sample contamination and these encountered due to matrix effects in order to avoid overestimating PAE concentrations in the environment.

Low density solvent based dispersive liquid–liquid microextraction followed by vortex-assisted magnetic nanoparticle based solid-phase extraction and surfactant enhanced spectrofluorimetric detection for the determination of aflatoxins in pistachio nuts

A novel extraction method based on DLLME followed by VA-D-SPE was developed to determine total aflatoxins in pistachio.

Metal–organic framework MIL-101(Cr) as a sorbent of porous membrane-protected micro-solid-phase extraction for the analysis of six phthalate esters from drinking water: a combination of experimental and computational study

An attractive MIL-101(Cr) material was synthesized and applied as a sorbent in μ-SPE device for the pre-concentration of PAEs in drinking water for the first time.

Extraction and GC-MS analysis of phthalate esters in food matrices: a review

According to the Scopus database, using “phthalate” and “GC” as keywords, 758 papers have been found between 1990 and 2014, showing strong and increasing interest in this class of compounds from the scientific community.

Ultra-preconcentration and determination of organophosphorus pesticides in soil samples by a combination of ultrasound assisted leaching-solid phase extraction and low-density solvent based dispersive liquid–liquid microextraction

USAL-SPE-LDS-DLLME has been applied for the determination of OPPs in soil samples.