Subject specific finite element analysis of implant stability for a cementless femoral stem

3-D finite element model of the impaction of a press-fitted femoral stem under various biomechanical environments

BACKGROUND

Uncemented femoral stem insertion into the bone is achieved by applying successive impacts on an inserter tool called "ancillary". Impact analysis has shown to be a promising technique to monitor the implant insertion and to improve its primary stability.

METHOD

This study aims to provide a better understanding of the dynamic phenomena occurring between the hammer, the ancillary, the implant and the bone during femoral stem insertion, to validate the use of impact analyses for implant insertion monitoring. A dynamic 3-D finite element model of the femoral stem insertion via an impaction protocol is proposed. The influence of the trabecular bone Young's modulus (Et), the interference fit (IF), the friction coefficient at the bone-implant interface (μ) and the impact velocity (v0) on the implant insertion and on the impact force signal is evaluated.

RESULTS

For all configurations, a decrease of the time difference between the two first peaks of the impact force signal is observed throughout the femoral stem insertion, up to a threshold value of 0.23 ms. The number of impacts required to reach this value depends on Et, v0 and IF and varies between 3 and 8 for the set of parameters considered herein. The bone-implant contact ratio reached after ten impacts varies between 60% and 98%, increases as a function of v0 and decreases as a function of IF, μ and Et.

CONCLUSION

This study confirms the potential of an impact analyses-based method to monitor implant insertion and to retrieve bone-implant contact properties.

Advancement in total hip implant: a comprehensive review of mechanics and performance parameters across diverse novelties

The UK's National Joint Registry (NJR) and the American Joint Replacement Registry (AJRR) of 2022 revealed that total hip replacement (THR) is the most common orthopaedic joint procedure. The NJR also noted that 10-20% of hip implants require revision within 1 to 10 years. Most of these revisions are a result of aseptic loosening, dislocation, implant wear, implant fracture, and joint incompatibility, which are all caused by implant geometry disparity. The primary purpose of this review article is to analyze and evaluate the mechanics and performance factors of advancement in hip implants with novel geometries. The existing hip implants can be categorized based on two parts: the hip stem and the joint of the implant. Insufficient stress distribution from implants to the femur can cause stress shielding, bone loss, excessive micromotion, and ultimately, implant aseptic loosening due to inflammation. Researchers are designing hip implants with a porous lattice and functionally graded material (FGM) stems, femur resurfacing, short-stem, and collared stems, all aimed at achieving uniform stress distribution and promoting adequate bone remodeling. Designing hip implants with a porous lattice FGM structure requires maintaining stiffness, strength, isotropy, and bone development potential. Mechanical stability is still an issue with hip implants, femur resurfacing, collared stems, and short stems. Hip implants are being developed with a variety of joint geometries to decrease wear, improve an angular range of motion, and strengthen mechanical stability at the joint interface. Dual mobility and reverse femoral head-liner hip implants reduce the hip joint's dislocation limits. In addition, researchers reveal that femoral headliner joints with unidirectional motion have a lower wear rate than traditional ball-and-socket joints. Based on research findings and gaps, a hypothesis is formulated by the authors proposing a hip implant with a collared stem and porous lattice FGM structure to address stress shielding and micromotion issues. A hypothesis is also formulated by the authors suggesting that the utilization of a spiral or gear-shaped thread with a matched contact point at the tapered joint of a hip implant could be a viable option for reducing wear and enhancing stability. The literature analysis underscores substantial research opportunities in developing a hip implant joint that addresses both dislocation and increased wear rates. Finally, this review explores potential solutions to existing obstacles in developing a better hip implant system.

Does preclinical analysis based on static loading underestimate post-surgery stem micromotion in THA as opposed to dynamic gait loading?

The success of cementless hip stems depends on the primary stability of the implant quantified by the amount of micromotion at the bone-stem interface. Most finite element (FE)-based preclinical studies on post-surgery stem stability rely on static analysis. Hence, the effect of dynamic gait loading on bone-stem relative micromotion remains virtually unexplored. Furthermore, there is a paucity of research on the primary stability of grooved stems as opposed to plain stem design. The primary aim of this FE study was to understand whether transient dynamic gait had any incremental effect on the net micromotion results and to further draw insights into the effects of grooved texture vis-à-vis a plain model on micromotion and proximal load transfer in host bone. Two musculoskeletal loading regimes corresponding to normal walking (NW) and stair climbing (SC) were considered. Although marginally improved load transfer was predicted proximally for the grooved construct under static loading, the micromotion values (max: NW ~ 7 μm; SC ~ 10 μm) were found to be considerably less in comparison to plain stem (max: NW ~ 50 μm; SC ~ 20 μm). For both physiological load cases, a significant surge in micromotion values was predicted in dynamic analyses as opposed to static analyses for the grooved stem (~ 390% greater). For the plain model, the increase in these values from static to dynamic loading is relatively moderate yet clinically significant (~ 230% greater). This suggests that the qualitative similarities notwithstanding, there were significant dissimilarities in the quantitative trends of micromotion for different cases under both analyses.

A novel hybrid design and modelling of a customised graded Ti-6Al-4V porous hip implant to reduce stress-shielding: An experimental and numerical analysis

Stress shielding secondary to bone resorption is one of the main causes of aseptic loosening, which limits the lifespan of hip prostheses and exacerbates revision surgery rates. In order to minimise post-hip replacement stress variations, this investigation proposes a low-stiffness, porous Ti6Al4V hip prosthesis, developed through selective laser melting (SLM). The stress shielding effect and potential bone resorption properties of the porous hip implant were investigated through both in vitro quasi-physiological experimental assays, together with finite element analysis. A solid hip implant was incorporated in this investigation for contrast, as a control group. The stiffness and fatigue properties of both the solid and the porous hip implants were measured through compression tests. The safety factor of the porous hip stem under both static and dynamic loading patterns was obtained through simulation. The porous hip implant was inserted into Sawbone/PMMA cement and was loaded to 2,300 N (compression). The proposed porous hip implant demonstrated a more natural stress distribution, with reduced stress shielding (by 70%) and loss in bone mass (by 60%), when compared to a fully solid hip implant. Solid and porous hip stems had a stiffness of 2.76 kN/mm and 2.15 kN/mm respectively. Considering all daily activities, the porous hip stem had a factor of safety greater than 2. At the 2,300 N load, maximum von Mises stresses on the hip stem were observed as 112 MPa on the medial neck and 290 MPa on the distal restriction point, whereby such values remained below the endurance limit of 3D printed Ti6Al4V (375 MPa). Overall, through the strut thickness optimisation process for a Ti6Al4V porous hip stem, stress shielding and bone resorption can be reduced, therefore proposing a potential replacement for the generic solid implant.

Influence of the biomechanical environment on the femoral stem insertion and vibrational behavior: a 3-D finite element study

The long-term success of cementless surgery strongly depends on the implant primary stability. The femoral stem initial fixation relies on multiple geometrical and material factors, but their influence on the biomechanical phenomena occurring during the implant insertion is still poorly understood, as they are difficult to quantify in vivo. The aim of the present study is to evaluate the relationship between the resonance frequencies of the bone-implant-ancillary system and the stability of the femoral stem under various biomechanical environments. The interference fit IF, the trabecular bone Young's modulus [Formula: see text] and the bone-implant contact friction coefficient [Formula: see text] are varied to investigate their influence on the implant insertion phenomena and on the system vibration behavior. The results exhibit for all the configurations, a nonlinear increase in the bone-implant contact throughout femoral stem insertion, until the proximal contact is reached. While the pull-out force increases with [Formula: see text], IF and [Formula: see text], the bone-implant contact ratio decreases, which shows that a compromise on the set of parameters could be found in order to achieve the largest bone-implant contact while maintaining sufficient pull-out force. The modal analysis on the range [2-7] kHz shows that the resonance frequencies of the bone-implant-ancillary system increase with the bone-implant contact ratio and the trabecular bone Young's modulus, with a sensitivity that varies over the modes. Both the pull-out forces and the vibration behavior are consistent with previous experimental studies. This study demonstrates the potential of using vibration methods to guide the surgeons for optimizing implant stability in various patients and surgical configurations.

Stress Shielding and Bone Resorption of Press-Fit Polyether-Ether-Ketone (PEEK) Hip Prosthesis: A Sawbone Model Study

Stress shielding secondary to bone resorption is one of the main causes of aseptic loosening, which limits the lifespan of the hip prostheses and increases the rates of revision surgery. This study proposes a low stiffness polyether-ether-ketone (PEEK) hip prostheses, produced by fused deposition modelling to minimize the stress difference after the hip replacement. The stress shielding effect and the potential bone resorption of the PEEK implant was investigated through both experimental tests and FE simulation. A generic Ti6Al4V implant was incorporated in this study to allow fair comparison as control group. Attributed to the low stiffness, the proposed PEEK implant showed a more natural stress distribution, less stress shielding (by 104%), and loss in bone mass (by 72%) compared with the Ti6Al4V implant. The stiffness of the Ti6Al4V and the PEEK implant were measured through compression tests to be 2.76 kN/mm and 0.276 kN/mm. The factor of safety for the PEEK implant in both static and dynamic loading scenarios were obtained through simulation. Most of the regions in the PEEK implant were tested to be safe (FoS larger than 1) in terms of representing daily activities (2300 N), while the medial neck and distal restriction point of the implant attracts large von Mises stress 82 MPa and 76 MPa, respectively, and, thus, may possibly fail during intensive activities by yield and fatigue. Overall, considering the reduction in stress shielding and bone resorption in cortical bone, PEEK could be a promising material for the patient-specific femoral implants.

Patient-specific three-dimensional evaluation of interface micromotion in two different short stem designs in cementless total hip arthroplasty: a finite element analysis

Background

Evaluation of micromotion in various activities in daily life is essential to the assessment of the initial fixation of cementless short stems in total hip arthroplasty. This study sought to evaluate three-dimensionally the micromotion of two types of cementless short stems.

Methods

Two types of stems were used: the Fitmore stem with a rectangular cross-section (rectangular stem) and the octagonal-oval GTS stem with fins (finned stem). Finite element analysis was used to calculate the micromotion of two activities that place a heavy load on the stem (single-leg stance and stair climbing). Three values were measured: the magnitude of micromotion (mean and 95th percentile), the location of micromotion above the 95th percentile value, and the directions of the micromotion vector.

Results

1. There was no significant difference in the magnitude of the micromotion between the rectangular stem and finned stem groups for single-leg stance or stair climbing. 2. In both groups, the micromotion was greatest at the proximal and distal ends. 3. The direction of the micromotion was similar in both groups; internal rotation occurred from the distal to the middle of the stem during stair climbing.

Conclusions

The rectangular stem had comparable initial fixation to that of the finned stem. In both models, the micromotion was greater at the proximal and distal ends. The direction of the micromotion was not dependent on the stem shape but on the direction of the load on the artificial femoral head. These results will be important for stem selection and future stem development.

Supplementary Information

The online version contains supplementary material available at 10.1186/s13018-022-03329-5.

Towards a validated patient-specific computational modeling framework to identify failure regions in traditional growing rods in patients with early onset scoliosis

Background

While growing rods are an important contribution to early-onset scoliosis treatment, rod fractures are a common complication that require reoperations. A recent retrieval analysis study performed on failed traditional growing rods revealed that there are commonalities among patient characteristics based on the location of rod fracture. However, it remains unknown if these locations correspond to high stress regions in the implanted construct.

Methods

A patient-specific finite element scoliotic model was developed to match the pre-operative (pre-op) scoliotic curve of a patient as described in previously published articles, and by using the patient registry information along with biplanar radiographs. A dual stainless-steel traditional growing rod construct was implanted into this scoliotic model and the surgical procedure was simulated to match the post-operative (post-op) scoliotic curve parameters. Muscle stabilization and gravity was simulated through follower load application. Rod distraction magnitudes were chosen based on pre-op to post-op cobb angle correction, and flexion bending load was simulated to identify the high stress regions on the rods.

Results

The patient-specific finite element model identified two high stress regions on the posterior surface of the rods, one at mid construct and the other adjacent to the distal anchors. This correlated well with the data obtained from the retrieval analysis performed by researchers at U.S. Food and Drug Administration (FDA) which showed the posterior surface of the rod as the fracture initiation site, and the three locations of failure as mid-construct, adjacent to distal anchors, and adjacent to tandem connector.

Conclusions

The result of this study confirms that the high stress regions on the growing rods, as identified by the FEA, match the fracture prone sites identified in the retrieval analysis performed at the FDA. This proof-of-concept patient-specific approach can be used to predict sites prone to fracture in growing rods.

QCT-FE modeling of the proximal tibia: Effect of mapping strategy on convergence time and model accuracy

Quantitative computed tomography (QCT) based finite element (FE) modeling, referred to as QCT-FE, has seen rapid growth and application for modeling bone mechanics. With this approach, varying bone material properties are set via experimentally-derived density-modulus equations. One challenge though associated with QCT-FE is to identify the appropriate mapping strategy for assigning elastic moduli to elements. The goal of this study was to evaluate different QCT-FE mapping strategies to identify the optimum approach with fastest convergence rate and highest accuracy. Four proximal tibial medial compartments were imaged using QCT and experimentally tested to characterize proximal tibial subchondral bone stiffness at four surface points, resulting in a total of 16 indentation measures. Three material mapping methods were analyzed: (1) constant-E where an average elastic modulus was assigned to each element; (2) node-based where the material properties were first mapped on nodes then interpolated to Gaussian integration points; and (3) element-based in which the material properties were directly assigned to Gaussian integration points. Different element sizes were assessed with edge-lengths ranging from 0.9 to 3 mm. Results indicated that all converged models showed similar coefficient-of-determination (R²) and normalized root-mean-square errors (RMSE%). Though, the constant-E and node-based methods converged with the element edge-length of 1.5 mm (prediction error of 4.8% and 2.5%, respectively) whereas the element-based method converged with a larger element having an edge-length 2.5 mm (error = 4.9%). In conclusion, the element-based method, with a larger element size, resulted in similar predictive accuracy, faster convergence and shorter run-times relative to the constant-E and node-based approaches. As such, we recommend the element-based method for future subject-specific QCT-FE modeling.

The effect of different interference fits on the primary fixation of a cementless femoral component during experimental testing

Cementless femoral total knee arthroplasty (TKA) components use a press-fit (referred to as interference fit) to achieve initial fixation. A higher interference fit could lead to a superior fixation, but it could also introduce more damage to the bone during implantation. The purpose of the current study was to investigate the effect of interference fit on the micromotions and gap opening/closing at the bone-implant interface. Experimental tests were performed in six pairs of cadaveric femurs implanted with femoral components using a low interference fit of 350 μm and a high interference fit of 700 μm. The specimens were subjected to the peak loads of gait and squat, based on the Orthoload dataset. Digital Image Correlation (DIC) was used to measure the micromotions and opening/closing in different regions of interest (ROIs). Two linear mixed-effect statistical models were created with micromotions and gap opening/closing as dependent variables. ROIs, loading conditions, and implant designs as independent variables, and cadaver specimens as random intercepts. The results revealed no significant difference between the two interference fit implants for micromotions (p = 0.837 for gait and p = 0.065 for squat), nor for the gap opening/closing (p = 0.748 for gait and p = 0.561 for squat). In contrast, significant differences were found between loading and most of the ROIs in both dependent variables (p < 0.0001). Additionally, no difference in bone deformation was found between low and high interference fit. Changing interference between either 350 μm or 700 μm did not affect the primary stability of a femoral TKA component. There could be an interference fit threshold beyond which fixation does not further improve.

The influence of loading configurations on numerical evaluation of failure mechanisms in an uncemented femoral prosthesis

The clinical relevance of numerical predictions of failure mechanisms in femoral prosthesis could be impaired due to simplification of musculoskeletal loading. This study investigated the extent to which loading configurations affect the preclinical analysis of an uncemented femoral implant. Patient-specific, CT-scan based FE models of intact and implanted femurs were developed and analysed using three loading configurations, which comprised of load cases representing daily activities. First loading configuration consisted of two load cases, each of walking and stair climbing. The second consisted of more number of load cases for each of these activities. The third included load cases of additional activities of standing up and sitting down. Failure criteria included maximum principal strains, interface debonding, implant-bone relative displacement and adaptive bone remodelling. Simplified loading configurations led to a reduction (100-1500 με) around cortical principal strains. The area prone to interface debonding were observed in the proximo-medial part of implant and was maximum when all activities were considered. This area was reduced by 35%, when simplified loading configurations were chosen. Interfacial area of 88%-96% experienced implant-bone relative displacements below 40 μm; however maximum of 110 μm was observed at the calcar region. Lack of consideration of variety of activities overestimated (30%-50%) bone resorption around the lateral part of the implant; hence, these bone remodelling results were less clinically relevant. Considering a variety daily activities along with an adequate number of load cases for each activity seemed necessary for pre-clinical evaluations of reconstructed femur.

Comparisons of the surface micromotions of cementless femoral prosthesis in the horizontal and vertical levels: a network analysis of biomechanical studies

BACKGROUND

Numerous quantitatively biomechanical studies measuring the fixation stability of femoral stem using micromotions at the bone-implant interfaces in different directions and levels remain inconclusive. This network meta-analysis performed systematically aims to explore the rank probability of micromotions at the bone-implant interfaces based on biomechanical data from studies published.

METHODS

Two electronic databases, PubMed/MEDLINE and Embase, were utilized to retrieve biomechanical studies providing the data of micromotions at the bone-stem interfaces. After screening and diluting out, the studies that met inclusion criteria will be utilized for statistical analysis. In order to contrast the stability of commonness and differences of the different parts of the femoral stem, the horizontal and vertical comparison of micromotions at the bone-implant interfaces were conducted using the pooled evaluation indexes including the mean difference (MD) and the surface under the cumulative ranking (SUCRA) curve, while inconsistency analysis, sensitivity analysis, subgroup analyses, and publication bias were performed for the stability evaluation of outcomes.

RESULTS

Screening determined that 20 studies involving a total of 249 samples were deemed viable for inclusion in the network meta-analysis. Tip point registered the highest micromotions of 13 measurement points. In the horizontal level, the arrangements of 4 measurement points at the proximal (P1-P4), middle (P5-P8) and distal part of the stem (P9-P12) were P1 = P2 = P3 = P4, P7 > P8 > P6 = P5 and P10 ≥ P12 = P9 = P11, respectively. In the vertical level, the arrangements of 3 measurement points at the anterior, posterior, medial, and lateral directions was P9 > P5 = P1, P10 > P6 > P2, P11 > P7 > P3, and P12 > P8 > P4, respectively.

CONCLUSION

The network meta-analysis seems to reveal that the distal part of the femoral stem is easier to register higher micromotion, and tip point of femoral stem registers the highest micromotions.

On the design and properties of porous femoral stems with adjustable stiffness gradient

There is a large gap between the elastic modulus of the existing femoral stem and the host bone. This gap can lead to long-term complications, such as aseptic loosening and, eventually, a need for revision surgery. The porous metallic biomimetic femoral stem can effectively reduce stress shielding and provide firm implant fixation through bone ingrowth. The purpose of this research is to investigate the application of different porous femoral stems in relieving bone resorption and promoting osseointegration by finite element analysis. We present an intuitive visualization method based on a diamond lattice structure to understand the relationship between pore size, porosity, bone ingrowth criteria and additive manufacturing constraints. We further obtain an admissible design space of diamond lattice structure for porosity selection. We evaluate the relative micromotion of bone-implant interface and bone volume with density loss for three femoral stems with diamond lattice-based homogenous porous structures in admissible design space. We also evaluate porous femoral stems with four different grading orientations along the axial and radial directions of the femoral stem. These include an axial graded femoral stem with a porosity increased distally (DAGS), an axial graded femoral stem with a porosity increased proximally (PAGS), a radial graded femoral stem with a porosity increased inwardly (IRGS), and a radial graded femoral stem with a porosity increased externally (ERGS). The results indicate that: (i) homogenous porous femoral stems with 40% porosity, (ii) DAGS and (iii) IRGS can maintain the relative micromotion of the bone-implant interface in the safety range for bone ingrowth. The calculated volumes of bone with density loss in the cases of DAGS and IRGS are 3.6% and 3.3%, respectively, which are nearly 74% lower than that of fully dense stems. Therefore, DAGS and IRGS have an evident advantage in promoting osseointegration and relieving bone resorption. Thus, the graded femoral stem is more promising than the homogeneous porous stem.

A Vibrational Technique for In Vitro Intraoperative Prosthesis Fixation Monitoring

OBJECTIVE

In this paper, a new vibrational modal analysis technique was developed for intraoperative cementless prosthesis fixation evaluation upon hammering.

METHODS

An artificial bone (Sawbones)-prosthesis system was excited by sweeping of a sine signal over a wide frequency range. The exponential sine sweep technique was implemented to the response signal in order to determine the linear impulse response. Recursive Fourier transform enhancement (RFTE) technique was applied to the linear impulse response signal in order to enhance the frequency spectrum with sharp and distinguishable peak values indicating distinct high natural frequencies of the system (ranging from 15 kHz to 90 kHz). The experiment was repeated with 5 Sawbones-prosthesis samples. Upon successive hammering during the prosthesis insertion, variation of each natural frequency was traced.

RESULTS

Compared to classical Fast Fourier Transform, RFTE provided a better tracing and enhancement of frequency components during insertion. Three different types of frequency evolving trends (monotonically increasing, insensitive, and plateau-like) were observed for all samples, as confirmed by a new finite element simulation of the prosthesis dynamic insertion. Two main mechanical phenomena (i.e., geometrical compaction and compressive stress) were shown to govern these trends in opposite ways. Follow-up of the plateau-like trend upon hammering showed that the frequency shift is a good indicator of fixation.

CONCLUSION

Alongside the individual follow-up of frequency shifts, combinatorial frequency analysis provides new objective information on the mechanical stability of Sawbone-prosthesis fixation.

SIGNIFICANCE

The proposed vibrational technique based on RTFE can provide the surgeon with a new assistive diagnostic technique during the surgery by indicating when the bone-prosthesis fixation is acceptable, and beyond of which further hammering should be done cautiously to avoid bone fracture.

A comparative assessment of two designs of hip stem using rule-based simulation of combined osseointegration and remodelling

The stem–bone interface of cementless total hip arthroplasty undergoes an adaptive process of bone ingrowth until the two parts become osseointegrated. Another important phenomenon associated with aseptic loosening of hip stem is stress-shielding induced adverse bone remodelling. The objective of this study was to preclinically assess the relative performances of two distinct designs of hip stems by addressing the combined effect of bone remodelling and osseointegration, based on certain rule-based criteria obtained from the literature. Premised upon non-linear finite element analyses of patient-specific implanted femur models, the study attempts to ascertain in silico outcome of the hip stem designs based on an evolutionary interfacial condition, and to further comment on the efficacy of the rule-based technique on the prediction of peri-prosthetic osseointegration. One of the two hip stem models was a trade-off design obtained from an earlier shape optimization study, and the other was based on TriLock stem (DePuy). Both designs predicted similar long-term osseointegration (∼89% surface), although trade-off stem predicted higher post-operative osseointegration. Proximal bone resorption was found higher for TriLock (by ∼110%) as compared to trade-off model. The rule-based technique predicted clinically coherent osseointegration around both stems and appears to be an alternative to expensive mechanobiology-based schemes.

Quantification of interfacial motions following primary and revision total knee arthroplasty: A verification study versus experimental data

Motion at the bone-implant interface, following primary or revision knee arthroplasty, can be detrimental to the long-term survival of the implant. This study employs experimentally verified computational models of the distal femur to characterize the relative motion at the bone-implant interface for three different implant types; a posterior stabilizing implant (PS), a total stabilizing implant (TS) with short stem (12 mm × 50 mm), and a total stabilizing implant (TS) with long offset stem (19 mm × 150 mm with a 4 mm lateral offset). Relative motion was investigated for both cemented and uncemented interface conditions. Monitoring relative motion about a single reference point, though useful for discerning global differences between implant types, was found to not be representative of the true pattern and distribution of motions which occur at the interface. The contribution of elastic deformation to apparent reference point motion varied based on implant type, with the PS and TSSS implanted femurs experiencing larger deformations (43 and 39 μm, respectively) than the TSLS implanted femur (22 μm). Furthermore, the pattern of applied loading was observed to greatly influence location and magnitude of peak motions, as well as the surface area under increased motion. Interestingly, the influence was not uniform across all implant types, with motions at the interface of long stemmed prosthesis found to be less susceptible to changes in pattern of loading. These findings have important implications for the optimization and testing of orthopedic implants in vitro and in silico. © 2017 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 36:387-396, 2018.

Modal analysis for the assessment of cementless hip stem primary stability in preoperative THA planning

This numerical vibration finite element (FE) study introduces resonance three-dimensional planning (RP3D) to assess preoperatively the primary stability of a cementless stem for total hip arthroplasty. Based on a patient's CT-scan and a numerical model of a stem, RP3D aims at providing mechanical criteria indicative of the achievable primary stability. We investigate variations of the modal response of the stem to changes of area and apparent stiffness of the bone-implant interface. The model is computationally cheap as it does not include a mesh of the bone. The apparent stiffness of the bone is modeled by springs attached to the nodes of the stem's mesh. We investigate an extended range of stiffness values while, in future works, patient's specific Hounsfield values could be used to define stiffness. We report modal frequencies, shapes, and a ratio of elastic potential energies (rEPE) that quantifies the proximal motion that should be minimum for a stable stem. The modal response exhibits a clear transition between loose and tight contact as area and stiffness of the interface increase. rEPE thresholds that could potentially discriminate preoperatively between stable and unstable stems are given for a Symbios SPS^® size C stem.

A biomechanical testing system to determine micromotion between hip implant and femur accounting for deformation of the hip implant: Assessment of the influence of rigid body assumptions on micromotions measurements

BACKGROUND

Accurate pre-clinical evaluation of the initial stability of new cementless hip stems using in vitro micromotion measurements is an important step in the design process to assess the new stem's potential. Several measuring systems, linear variable displacement transducer-based and other, require assuming bone or implant to be rigid to obtain micromotion values or to calculate derived quantities such as relative implant tilting.

METHODS

An alternative linear variable displacement transducer-based measuring system not requiring a rigid body assumption was developed in this study. The system combined advantages of local unidirectional and frame-and-bracket micromotion measuring concepts. The influence and possible errors that would be made by adopting a rigid body assumption were quantified. Furthermore, as the system allowed emulating local unidirectional and frame-and-bracket systems, the influence of adopting rigid body assumptions were also analyzed for both concepts. Synthetic and embalmed bone models were tested in combination with primary and revision implants. Single-legged stance phase loading was applied to the implant - bone constructs.

FINDINGS

Adopting a rigid body assumption resulted in an overestimation of mediolateral micromotion of up to 49.7μm at more distal measuring locations. Maximal average relative rotational motion was overestimated by 0.12° around the anteroposterior axis. Frontal and sagittal tilting calculations based on a unidirectional measuring concept underestimated the true tilting by an order of magnitude.

INTERPRETATION

Non-rigid behavior is a factor that should not be dismissed in micromotion stability evaluations of primary and revision femoral implants.

Characterization of Femoral Component Initial Stability and Cortical Strain in a Reduced Stem-Length Design

BACKGROUND

Short-stemmed femoral components facilitate reduced exposure surgical techniques while preserving native bone. A clinically successful stem should ideally reduce risk for stress shielding while maintaining adequate primary stability for biological fixation. We asked (1) how stem-length changes cortical strain distribution in the proximal femur in a fit-and-fill geometry and (2) if short-stemmed components exhibit primary stability on par with clinically successful designs.

METHODS

Cortical strain was assessed via digital image correlation in composite femurs implanted with long, medium, and short metaphyseal fit-and-fill stem designs in a single-leg stance loading model. Strain was compared to a loaded, unimplanted femur. Bone-implant micromotion was then compared with reduced lateral shoulder short stem and short tapered-wedge designs in cyclic axial and torsional testing.

RESULTS

Femurs implanted with short-stemmed components exhibited cortical strain response most closely matching that of the intact femur model, theoretically reducing the potential for proximal stress shielding. In micromotion testing, no difference in primary stability was observed as a function of reduced stem length within the same component design.

CONCLUSION

Our findings demonstrate that within this fit-and-fill stem design, reduction in stem length improved proximal cortical strain distribution and maintained axial and torsional stability on par with other stem designs in a composite femur model. Short-stemmed implants may accommodate less invasive surgical techniques while facilitating more physiological femoral loading without sacrificing primary implant stability.

Full-field measurement of micromotion around a cementless femoral stem using micro-CT imaging and radiopaque markers

A good primary stability of cementless femoral stems is essential for the long-term success of total hip arthroplasty. Experimental measurement of implant micromotion with linear variable differential transformers is commonly used to assess implant primary stability in pre-clinical testing. But these measurements are often limited to a few distinct points at the interface. New techniques based on micro-computed tomography (micro-CT) have recently been introduced, such as Digital Volume Correlation (DVC) or markers-based approaches. DVC is however limited to measurement around non-metallic implants due to metal-induced imaging artifacts, and markers-based techniques are confined to a small portion of the implant. In this paper, we present a technique based on micro-CT imaging and radiopaque markers to provide the first full-field micromotion measurement at the entire bone-implant interface of a cementless femoral stem implanted in a cadaveric femur. Micromotion was measured during compression and torsion. Over 300 simultaneous measurement points were obtained. Micromotion amplitude ranged from 0 to 24µm in compression and from 0 to 49µm in torsion. Peak micromotion was distal in compression and proximal in torsion. The technique bias was 5.1µm and its repeatability standard deviation was 4µm. The method was thus highly reliable and compared well with results obtained with linear variable differential transformers (LVDTs) reported in the literature. These results indicate that this micro-CT based technique is perfectly relevant to observe local variations in primary stability around metallic implants. Possible applications include pre-clinical testing of implants and validation of patient-specific models for pre-operative planning.

Determination of replicate composite bone material properties using modal analysis

Replicate composite bones are used extensively for in vitro testing of new orthopedic devices. Contrary to tests with cadaveric bone material, which inherently exhibits large variability, they offer a standardized alternative with limited variability. Accurate knowledge of the composite's material properties is important when interpreting in vitro test results and when using them in FE models of biomechanical constructs. The cortical bone analogue material properties of three different fourth-generation composite bone models were determined by updating FE bone models using experimental and numerical modal analyses results. The influence of the cortical bone analogue material model (isotropic or transversely isotropic) and the inter- and intra-specimen variability were assessed. Isotropic cortical bone analogue material models failed to represent the experimental behavior in a satisfactory way even after updating the elastic material constants. When transversely isotropic material models were used, the updating procedure resulted in a reduction of the longitudinal Young's modulus from 16.00GPa before updating to an average of 13.96 GPa after updating. The shear modulus was increased from 3.30GPa to an average value of 3.92GPa. The transverse Young's modulus was lowered from an initial value of 10.00GPa to 9.89GPa. Low inter- and intra-specimen variability was found.

Finite element analysis of cementless femoral stems based on mid- and long-term radiological evaluation

BACKGROUND

Femoral bone remodeling in response to stress shielding induces periprosthetic bone loss. Computerized finite element analysis (FEA) is employed to demonstrate differences in initial stress distribution. However, FEA is often performed without considering the precise sites at which the stem was fixed. We determined whether FEA reflects mid-term radiological examination exactly as predicted following long-term stress shielding.

METHODS

Femur-stem fixation sites were evaluated radiologically according to the location of spot welds in two anatomical cementless stem designs. Based on mid-term radiological results, four femur-stem bonding site conditions were defined as: (Condition A) no bonding; (Condition B) bonding within the 10 mm area proximal to the distal border of the porous area; (Condition C) bonding of the entire porous area; and (Condition D) bonding of the entire femoral stem, prior to conducting FEA analysis. Furthermore, we radiographically evaluated mid- and long-term stress shielding, and measured bone mineral density of the femur 10 years after total hip arthroplasty.

RESULTS

Spot welds appeared frequently around the border between the porous and smooth areas. FEA showed that, based on mid-term radiological evaluation, von Mises stress was reduced in condition B in the area proximal to the femur-stem bonding sites for both stem designs compared with condition A (no bonding). Conversely, von Mises stress at all areas of the femur-stem bonding sites in conditions C and D was higher than that in condition A. With respect to stress shielding progression, there was no significant difference between the two types of stem designs. However, stress shielding progressed and was significantly higher in the presence of spot welds (p = 0.001). In both stem designs, bone mineral density in zone VII was significantly lower than that in the contralateral hips.

CONCLUSIONS

These results indicate that FEA based on mid-term radiological evaluation may be helpful to predict the influence of long-term stress shielding more precisely.

Effect of femoral canal shape on mechanical stress distribution and adaptive bone remodelling around a cementless tapered-wedge stem

OBJECTIVES

In total hip arthroplasty (THA), the cementless, tapered-wedge stem design contributes to achieving initial stability and providing optimal load transfer in the proximal femur. However, loading conditions on the femur following THA are also influenced by femoral structure. Therefore, we determined the effects of tapered-wedge stems on the load distribution of the femur using subject-specific finite element models of femurs with various canal shapes.

PATIENTS AND METHODS

We studied 20 femurs, including seven champagne flute-type femurs, five stovepipe-type femurs, and eight intermediate-type femurs, in patients who had undergone cementless THA using the Accolade TMZF stem at our institution. Subject-specific finite element (FE) models of pre- and post-operative femurs with stems were constructed and used to perform FE analyses (FEAs) to simulate single-leg stance. FEA predictions were compared with changes in bone mineral density (BMD) measured for each patient during the first post-operative year.

RESULTS

Stovepipe models implanted with large-size stems had significantly lower equivalent stress on the proximal-medial area of the femur compared with champagne-flute and intermediate models, with a significant loss of BMD in the corresponding area at one year post-operatively.

CONCLUSIONS

The stovepipe femurs required a large-size stem to obtain an optimal fit of the stem. The FEA result and post-operative BMD change of the femur suggest that the combination of a large-size Accolade TMZF stem and stovepipe femur may be associated with proximal stress shielding.Cite this article: M. Oba, Y. Inaba, N. Kobayashi, H. Ike, T. Tezuka, T. Saito. Effect of femoral canal shape on mechanical stress distribution and adaptive bone remodelling around a cementless tapered-wedge stem. Bone Joint Res 2016;5:362-369. DOI: 10.1302/2046-3758.59.2000525.

No effect of femoral offset on bone implant micromotion in an experimental model

BACKGROUND

In total hip replacement (THR), the femoral offset (FO) is assessed preoperatively, and the surgeon must determine whether to restore, increase, or decrease the FO based on experience and the patient's clinical history. The FO is known to influence the abductor muscle strength, range of motion (ROM), gait, and hip pain after THR; however, the true effect of FO on bone implant micromotion is unclear. Therefore, we investigated to assess: (1) the muscle loading response during gait, (2) whether FO affects bone implant micromotion during gait.

HYPOTHESIS

A variation of ±10mm from the anatomical FO affects the muscle loading forces.

MATERIALS AND METHODS

We modified a personalized musculoskeletal model of the lower extremity to determine the 3-dimensional contact forces at the hip joint in the presence of a stem with varying offsets during a gait cycle. A detailed finite element (FE) model was then constructed for increased, restored, and decreased FOs. The maximum load obtained during normal walking gait from the musculoskeletal model was applied to the respective FE models, and the resultant stem-bone micromotion and stress distribution were computed.

RESULTS

Increasing the FO to +10mm decreased the peak force generated by the abductor muscles during the cycle by 15.0% and decreasing the FO to -10mm increased the von Mises stress distribution at the distal bone by 77.5% (P<0.05). A variation of the offset within 10mm of the anatomical offset showed no significant differences in micromotion (P>0.05) and peak stresses (P>0.05).

DISCUSSION

Coupling the musculoskeletal model of the gait cycle with FE analysis provides a realistic model to understand how FO affects bone implant micromotion. We found that there was no effect of FO on bone implant micromotion; thus, a surgeon does not need to evaluate the implications of FO on micromotion and can determine a FO that best decreases the work load of abductor muscles, increases ROM, and reduces hip pain.

LEVEL OF EVIDENCE

IV, biomechanical study.

Four decades of finite element analysis of orthopaedic devices: where are we now and what are the opportunities?

Finite element has been used for more than four decades to study and evaluate the mechanical behaviour total joint replacements. In Huiskes seminal paper "Failed innovation in total hip replacement: diagnosis and proposals for a cure", finite element modelling was one of the potential cures to avoid poorly performing designs reaching the market place. The size and sophistication of models has increased significantly since that paper and a range of techniques are available from predicting the initial mechanical environment through to advanced adaptive simulations including bone adaptation, tissue differentiation, damage accumulation and wear. However, are we any closer to FE becoming an effective screening tool for new devices? This review contains a critical analysis of currently available finite element modelling techniques including (i) development of the basic model, the application of appropriate material properties, loading and boundary conditions, (ii) describing the initial mechanical environment of the bone-implant system, (iii) capturing the time dependent behaviour in adaptive simulations, (iv) the design and implementation of computer based experiments and (v) determining suitable performance metrics. The development of the underlying tools and techniques appears to have plateaued and further advances appear to be limited either by a lack of data to populate the models or the need to better understand the fundamentals of the mechanical and biological processes. There has been progress in the design of computer based experiments. Historically, FE has been used in a similar way to in vitro tests, by running only a limited set of analyses, typically of a single bone segment or joint under idealised conditions. The power of finite element is the ability to run multiple simulations and explore the performance of a device under a variety of conditions. There has been increasing usage of design of experiments, probabilistic techniques and more recently population based modelling to account for patient and surgical variability. In order to have effective screening methods, we need to continue to develop these approaches to examine the behaviour and performance of total joint replacements and benchmark them for devices with known clinical performance. Finite element will increasingly be used in the design, development and pre-clinical testing of total joint replacements. However, simulations must include holistic, closely corroborated, multi-domain analyses which account for real world variability.

Initial instability in total ankle replacement: a cadaveric biomechanical investigation of the STAR and agility prostheses

BACKGROUND

Design improvements have increased the success of total ankle replacement, providing patients with end-stage ankle arthritis a viable alternative to arthrodesis. However, revision rates are higher than those for hip and knee arthroplasty, with the most prevalent cause of failure being aseptic loosening. The objective of this study was to quantify and compare the relative bone-implant motion patterns in two well-known total ankle replacement designs.

METHODS

A custom-designed mechanical simulator applied compressive loads (up to 300 N) and bending moments (3 Nm) to six pairs of human cadaveric ankles implanted with total ankle replacements, inducing a natural range of motion about three orthogonal axes: plantar flexion-dorsiflexion, inversion-eversion, and internal-external rotation. The implants analyzed were the Agility and the STAR (Scandinavian Total Ankle Replacement). The relative bone-implant motions for each implant component were measured with use of an optical motion capture system.

RESULTS

The Agility typically exhibited greater relative motion than the STAR, with significant differences for the tibial component in inversion-eversion (p = 0.037) and for the talar component in internal-external rotation (p = 0.039). The magnitudes of the relative motions were affected by the loading direction and by compression. The motion magnitudes were quite large, with values exceeding 1000 μm for the Agility talar component in plantar flexion-dorsiflexion and in inversion-eversion.

CONCLUSIONS

The greater magnitudes of relative motion in the Agility suggest that primary instability of the implant may contribute to its higher clinically observed aseptic loosening rate. Future total ankle replacement designs will require better fixation to improve outcomes. The results underscore the need to conduct preclinical biomechanical assessments of relative motion patterns in ankle replacements.

CLINICAL RELEVANCE

Stable initial implant fixation will likely improve clinical outcomes of total ankle replacement.

Primary stability recognition of the newly designed cementless femoral stem using digital signal processing

Stress shielding and micromotion are two major issues which determine the success of newly designed cementless femoral stems. The correlation of experimental validation with finite element analysis (FEA) is commonly used to evaluate the stress distribution and fixation stability of the stem within the femoral canal. This paper focused on the applications of feature extraction and pattern recognition using support vector machine (SVM) to determine the primary stability of the implant. We measured strain with triaxial rosette at the metaphyseal region and micromotion with linear variable direct transducer proximally and distally using composite femora. The root mean squares technique is used to feed the classifier which provides maximum likelihood estimation of amplitude, and radial basis function is used as the kernel parameter which mapped the datasets into separable hyperplanes. The results showed 100% pattern recognition accuracy using SVM for both strain and micromotion. This indicates that DSP could be applied in determining the femoral stem primary stability with high pattern recognition accuracy in biomechanical testing.

Fixation of the shorter cementless GTS™ stem: biomechanical comparison between a conventional and an innovative implant design

INTRODUCTION

Conventional cementless total hip arthroplasty already shows very good clinical results. Nevertheless, implant revision is often accompanied by massive bone loss. The new shorter GTS™ stem has been introduced to conserve femoral bone stock. However, no long-term clinical results were available for this implant. A biomechanical comparison of the GTS™ stem with the clinically well-established CLS(®) stem was therefore preformed to investigate the targeted stem philosophy.

MATERIALS AND METHODS

Four GTS™ stems and four CLS(®) stems were implanted in a standardized manner in eight synthetic femurs. A high-precision measuring device was used to determine micromotions of the stem and bone during different load applications. Calculation of relative micromotions at the bone-implant interface allowed the rotational implant stability and the bending behavior of the stem to be determined.

RESULTS

Lowest relative micromotions were detected near the lesser trochanter within the proximal part of both stems. Maximum relative micromotions were measured near the distal tip of the stems, indicating a proximal fixation of both stems. For the varus-valgus-torque application, a comparable stem bending behavior was shown for both stems.

CONCLUSION

Both stems seem to provide a comparable and adequate primary stability. The shortened GTS™ design has a comparable rotational stability and bone-implant flexibility compared to a conventional stem. This study demonstrates that the CLS(®) stem and the GTS™ stem exhibit similar biomechanical behavior. However, a clinical confirmation of these experimental results is still required.

Design process of cementless femoral stem using a nonlinear three dimensional finite element analysis

BACKGROUND

Minimal available information concerning hip morphology is the motivation for several researchers to study the difference between Asian and Western populations. Current use of a universal hip stem of variable size is not the best option for all femur types. This present study proposed a new design process of the cementless femoral stem using a three dimensional model which provided more information and accurate analysis compared to conventional methods.

METHODS

This complete design cycle began with morphological analysis, followed by femoral stem design, fit and fill analysis, and nonlinear finite element analysis (FEA). Various femur parameters for periosteal and endosteal canal diameters are measured from the osteotomy level to 150 mm below to determine the isthmus position.

RESULTS

The results showed better total fit (53.7%) and fill (76.7%) canal, with more load distributed proximally to prevent stress shielding at calcar region. The stem demonstrated lower displacement and micromotion (less than 40 μm) promoting osseointegration between the stem-bone and providing primary fixation stability.

CONCLUSION

This new design process could be used as a preclinical assessment tool and will shorten the design cycle by identifying the major steps which must be taken while designing the femoral stem.

Accounting for patient variability in finite element analysis of the intact and implanted hip and knee: a review

It is becoming increasingly difficult to differentiate the performance of new joint replacement designs using available preclinical test methods. Finite element analysis is commonly used and the majority of published studies are performed on representative anatomy, assuming optimal implant placement, subjected to idealised loading conditions. There are significant differences between patients and accounting for this variability will lead to better assessment of the risk of failure. This review paper provides a comprehensive overview of the techniques available to account for patient variability. There is a brief overview of patient-specific model generation techniques, followed by a review of multisubject patient-specific studies performed on the intact and implanted femur and tibia. In particular, the challenges and limitations of manually generating models for such studies are discussed. To efficiently account for patient variability, the application of statistical shape and intensity models (SSIM) are being developed. Such models have the potential to synthetically generate thousands of representative models generated from a much smaller training set. Combined with the automation of the prosthesis implantation process, SSIM provides a potentially powerful tool for assessing the next generation of implant designs. The potential application of SSIM are discussed along with their limitations.

On stabilization of loosened hip stems via cement injection into osteolytic cavities

BACKGROUND

Cement injection into osteolytic areas around the cement mantle is a technique for refixation of loose hip implants for patients who cannot undergo standard revision surgery. Preliminary clinical results show the improvement in walking distance, patients' independence and pain relief.

METHODS

In this study, we use a detailed finite element model to analyze whether cement injection into osteolytic areas contributes to the overall implant stability. We study the effect of various factors, like location and size of osteolytic areas, interface conditions and bone stiffness on bone-cement relative motion.

FINDINGS

Presented results demonstrate that the procedure is most effective for the osteolytic areas located in the proximal region of the femur, while factors like a thin layer of residual fibrous tissue around the injected cement, that was not removed during the surgery, combined with reduced bone stiffness reduce the efficiency of the procedure.

INTERPRETATION

Cement injection is able to stabilize loosened hip prostheses. However, it is important to remove the fibrous tissue layer completely, as even a thin layer will negatively influence stabilization. We will focus our research efforts on developing fibrous tissue removal techniques in order to optimize this minimally invasive treatment.

Toward a more realistic prediction of peri-prosthetic micromotions

The finite element (FE) method has become a common tool to evaluate peri-prosthetic micromotions in cementless total hip arthroplasty. Often, only the peak joint load and a selected number of muscle loads are applied to determine micromotions. Furthermore, the applied external constraints are simplified (diaphyseal fixation), resulting in a non-physiological situation. In this study, a scaled musculoskeletal model was used to extract a full set of muscle and hip joint loads occurring during a walking cycle. These loads were applied incrementally to an FE model to analyze micromotions. The relation between micromotions and external loads was investigated, and how micromotions during a full loading cycle compared to those calculated when applying a peak load only. Finally, the effect of external constraints was analyzed (full model vs. diaphyseal fixation and reduced number of muscle loads). Relatively large micromotions were found during the swing phase when the hip joint forces were relatively low. Maximal micromotions, however, did concur with the peak hip joint force. Applying only a peak joint force resulted in peak micromotions similar to those found when full walking cycle loads were applied. The magnitude and direction of the micromotions depended on the applied muscle loads, but not on external constraints.

Primary stability and strain distribution of cementless hip stems as a function of implant design

BACKGROUND

Short stem prostheses have been developed to preserve the femoral bone stock. The purpose of this study was to evaluate the stress-shielding effect in the proximal femur as well as the micromotion between bone and implant as a measure of primary stability for a new short stem in comparison to a clinically successful short stem and a straight stem.

METHODS

Using paired fresh human femurs, stress shielding was examined by using tri-axial strain gage rosettes. The strain distribution of the proximal femur was measured before and after implantation of three cementless prostheses of different design concepts and stem lengths. Furthermore, interface motion and rotational stability were investigated under dynamic loading (100-1600 N) after 100,000 load cycles using inductive miniature displacement transducers.

FINDINGS

A reduction of longitudinal cortical strains in the proximal femur was displayed for all three implants. The reduction was less pronounced for the shorter stem implants, however. Interface motion was below the critical threshold of 150 μm at almost all measuring points for all three stems, with a tendency for greater rotational stability in the shorter stem implants.

INTERPRETATION

The new short stem prosthesis displayed reduced stress shielding and comparable primary stability to an established short stem and a conventional shaft design. Shortening the stem did not negatively influence primary stability. The clinical implications of these findings remain to be proven.

Experimental versus Computational Analysis of Micromotions at the Implant—Bone Interface

In total hip arthroplasty, micromotions at the implant—bone interface influence the long-term survival of the prosthesis. These micromotions are often measured using sensors that are fixed to the implant and bone at points that are remote from the interface. Given that the implant—bone system is not rigid, errors may be introduced. It is not possible to assess the magnitude of these errors with the currently available experimental methods. However, this problem can be investigated using the finite element method (FEM).

The hypothesis that the actual interface micromotions differ from those measured in the experimental manner was tested using a case-specific FE model, validated against deflection experiments. The FE model was used to simulate an ‘experimental’ method to measure micromotions. This ‘experimental’ method was performed by mimicking the distance between the measurement points; the implant point was selected at the interface while the bony point was at the outer surface of bone.

No correlation was found between the micromotions computed at the interface and when using remote reference points. Moreover, the magnitudes of micromotions computed with the latter method were considerably greater. By reducing the distance between the reference points the error decreased, but the correlation stayed unchanged. Care needs to be taken when interpreting the results of micromotion measurement systems that use bony reference points at a distance from the actual interface.

Analysis of bone-prosthesis interface micromotion for cementless tibial prosthesis fixation and the influence of loading conditions

A lack of initial stability of the fixation is associated with aseptic loosening of the tibial components of cementless knee prostheses. With sufficient stability after surgery, minimal relative motion between the prosthesis and bone interfaces allows osseointegation to occur thereby providing a strong prosthesis-to-bone biological attachment. Finite element modelling was used to investigate the bone-prosthesis interface micromotion and the relative risk of aseptic loosening. It was anticipated that by prescribing different joint loads representing gait and other activities, and the consideration of varying tibial-femoral contact points during knee flexion, it would influence the computational prediction of the interface micromotion. In this study, three-dimensional finite element models were set up with applied loads representing walking and stair climbing, and the relative micromotions were predicted. These results were correlated to in-vitro measurements and to the results of prior retrieval studies. Two load conditions, (i) a generic vertical joint load of 3 x body weight with 70%/30%M/L load share and antero-posterior/medial-lateral shear forces, acted at the centres of the medial and lateral compartments of the tibial tray, and (ii) a peak vertical joint load at 25% of the stair climbing cycle with corresponding antero-posterior shear force applied at the tibial-femoral contact points of the specific knee flexion angle, were found to generate interface micromotion responses which corresponded to in-vivo observations. The study also found that different loads altered the interface micromotion predicted, so caution is needed when comparing the fixation performance of various reported cementless tibial prosthetic designs if each design was evaluated with a different loading condition.