Load response of an osseointegrated implant used in the treatment of unilateral transfemoral amputation: An early implant loosening case study

Effect of different constraining boundary conditions on simulated femoral stresses and strains during gait

Finite element analysis (FEA) is commonly used in orthopaedic research to estimate localised tissue stresses and strains. A variety of boundary conditions have been proposed for isolated femur analysis, but it remains unclear how these assumed constraints influence FEA predictions of bone biomechanics. This study compared the femoral head deflection (FHD), stresses, and strains elicited under four commonly used boundary conditions (fixed knee, mid-shaft constraint, springs, and isostatic methods) and benchmarked these mechanics against the gold standard inertia relief method for normal and pathological femurs (extreme anteversion and retroversion, coxa vara, and coxa valga). Simulations were performed for the stance phase of walking with the applied femoral loading determined from patient-specific neuromusculoskeletal models. Due to unrealistic biomechanics observed for the commonly used boundary conditions, we propose a novel biomechanical constraint method to generate physiological femur biomechanics. The biomechanical method yielded FHD (< 1 mm), strains (approaching 1000 µε), and stresses (< 60 MPa), which were consistent with physiological observations and similar to predictions from the inertia relief method (average coefficient of determination = 0.97, average normalized root mean square error = 0.17). Our results highlight the superior performance of the biomechanical method compared to current methods of constraint for  both healthy and pathological femurs.

The biomechanical influence of transtibial Bone-Anchored limbs during walking

Individuals with unilateral transtibial amputation (TTA) using socket prostheses demonstrate asymmetric joint biomechanics during walking, which increases the risk of secondary comorbidities (e.g., low back pain (LBP), osteoarthritis (OA)). Bone-anchored limbs are an alternative to socket prostheses, yet it remains unknown how they influence multi-joint loading. Our objective was to determine the influence of bone-anchored limb use on multi-joint biomechanics during walking. Motion capture data (kinematics, ground reaction forces) were collected during overground walking from ten participants with unilateral TTA prior to (using socket prostheses) and 12-months after bone-anchored limb implantation. Within this year, each participant completed a rehabilitation protocol that guided progression of loading based on patient pain response and optimized biomechanics. Musculoskeletal models were developed at each testing timepoint (baseline or 12-months after implantation) and used to calculate joint kinematics, internal joint moments, and joint reaction forces (JRFs). Analyses were performed during three stance periods on each limb. The between-limb normalized symmetry index (NSI) was calculated for joint moments and JRF impulses. Discrete (range of motion (ROM), impulse NSI) dependent variables were compared before and after implantation using paired t-tests with Bonferroni-Holm corrections while continuous (ensemble averages of kinematics, moments, JRFs) were compared using statistical parametric mapping (p < 0.05). When using a bone-anchored limb, frontal plane pelvic (residual: pre = 9.6 ± 3.3°, post = 6.3 ± 2.5°, p = 0.004; intact: pre = 10.2 ± 3.9°, post = 7.9 ± 2.6°, p = 0.006) and lumbar (residual: pre = 15.9 ± 7.0°, post = 10.6 ± 2.5°, p = 0.024, intact: pre = 17.1 ± 7.0°, post = 11.4 ± 2.8°, p = 0.014) ROM was reduced compared to socket prosthesis use. The intact limb hip extension moment impulse increased (pre = -11.0 ± 3.6 Nm*s/kg, post = -16.5 ± 4.4 Nm*s/kg, p = 0.005) and sagittal plane hip moment impulse symmetry improved (flexion: pre = 23.1 ± 16.0 %, post = -3.9 ± 19.5 %, p = 0.004, extension: pre = 29.2 ± 20.3 %, post = 8.7 ± 22.9 %, p = 0.049). Residual limb knee extension moment impulse decreased compared to baseline (pre = 15.7 ± 10.8 Nm*s/kg, post = 7.8 ± 3.9 Nm*s/kg, p = 0.030). These results indicate that bone-anchored limb implantation alters multi-joint biomechanics, which may impact LBP or OA risk factors in the TTA population longitudinally.

Unilateral transfemoral osseointegrated prostheses improve joint loading during walking

People with unilateral transfemoral amputation using socket prostheses are at increased risk for developing osteoarthritis in both the residual hip and intact lower-limb joints. Osseointegrated prostheses are a surgical alternative to socket prostheses that directly attach to the residual femur via a bone-anchored implant, however their multi-joint loading effect is largely unknown. Our objective was to establish how osseointegrated prostheses influence joint loading during walking. Motion capture data (kinematics, ground reaction forces) were collected from 12 participants at baseline, with socket prostheses, and 12-months after prosthesis osseointegration during overground walking at self-selected speeds. Subject-specific musculoskeletal models were developed at each timepoint relative to osseointegration. Internal joint moments were calculated using inverse dynamics, muscle and joint reaction forces (JRFs) were estimated with static optimization. Changes in internal joint moments, JRFs, and joint loading-symmetry were compared using statistical parametric mapping (p≤ 0.05) before and after osseointegration. Amputated limb hip flexion moments and anterior JRFs decreased during terminal stance (p = 0.002, <0.001; respectively), while amputated limb hip abduction moments increased during mid-stance (p < 0.001), amputated hip rotation moment changed from internal to external throughout early stance (p < 0.001). Intact limb hip extension and knee flexion moments (p = 0.028, 0.032; respectively), superior and resultant knee JRFs (p = 0.046, 0.049; respectively) decreased during the loading response following prosthesis osseointegration. These results may indicate that the direct loading transmission of these novel prostheses create a more typical mechanical environment in bilateral joints, which is comparable with loading observed in able-bodied individuals and could decrease the risk of development or progression of osteoarthritis.

Use of computer tomography imaging for analyzing bone remodeling around a percutaneous osseointegrated implant

Osseointegration (OI) is being used for the direct skeletal attachment of prosthetic limbs using an intramedullary stem that extends percutaneously from the subject's residual limb. For this technology to be successful, bone ingrowth and remodeling around the implant must occur. Physicians need an effective way to assess bone remodeling to make informed treatment and rehabilitation decisions. Previous studies utilizing two-dimensional imaging X-ray as a tool to monitor bone-remodeling around OI devices have limitations. This study describes methodology that was developed utilizing computed tomography (CT) imaging as a tool for analyzing bone remodeling around a percutaneous OI implant. Six transfemoral amputees implanted with a percutaneous osseointegrated prosthesis (POP) had CT scans taken of their residual femur at 6 and 52 weeks postoperatively. Three-dimensional femoral models were processed using custom MATLAB script to collect cortical and medullary morphology measurements. Morphology data from 6- and 52-week scans were compared to quantify bone remodeling around the POP implant. Fifty-two weeks after implantation of the POP device, increases in cortical bone area and thickness were observed around the porous-coated stem. Minimal changes were observed in the medullary canal parameters within the periprosthetic regions. This study successfully utilized CT imaging and three-dimensional modeling techniques to analyze longitudinal data of bone remodeling around a transfemoral percutaneous implant. These methods have the potential to be used as a clinical tool for evaluating orthopedic implants in vivo. Data collected suggests that the POP device achieved the desired bone remodeling around the porous-coated region of the implanted stem.

Biomechanical compensations during a stand-to-sit maneuver using transfemoral osseointegrated prostheses: A case series

BACKGROUND

Patients with transfemoral amputation and socket prostheses are at a heightened risk of developing musculoskeletal overuse injuries, commonly due to altered joint biomechanics. Osseointegrated prostheses, which involve direct anchorage of the prosthesis to the residual limb through a bone anchored prosthesis, are a novel alternative to sockets yet their biomechanical effect is largely unknown.

METHODS

Four patients scheduled to undergo unilateral transfemoral prosthesis osseointegration completed two data collections (baseline with socket prosthesis and 12-months after prosthesis osseointegration) in which whole-body kinematics and ground reaction forces were collected during stand-to-sit tasks. Trunk, pelvis, and hip kinematics, and the surrounding muscle forces, were calculated using subject-specific musculoskeletal models developed in OpenSim. Peak joint angles and muscle forces were compared between timepoints using Cohen's d effect sizes.

FINDINGS

Compared to baseline with socket prostheses, patients with osseointegrated prostheses demonstrated reduced lateral trunk bending (d = 1.46), pelvic obliquity (d = 1.09), and rotation (d = 1.77) toward the amputated limb during the stand to sit task. This was accompanied by increased amputated limb hip flexor, abductor, and rotator muscle forces (d> > 0.8).

INTERPRETATION

Improved lumbopelvic movement patterns and stabilizing muscle forces when using an osseointegrated prosthesis indicate that this novel prosthesis type likely reduces the risk of the development and/or progression of overuse injuries, such as low back pain and osteoarthritis. We attribute the increased muscle hip muscle forces to the increased load transmission between the osseointegrated prosthesis and residual limb, which allows a greater eccentric ability of the amputated limb to control lowering during the stand-to-sit task.

Finite Element Analysis of Transhumeral and Transtibial Percutaneous Osseointegrated Endoprosthesis Implantation

Cadaveric mechanical testing of a percutaneous osseointegration docking system (PODS) for osseointegration (OI) prosthetic limb attachment revealed that translation of the exact system from the humerus to the tibia may not be suitable. The PODS, designed specifically for the humerus achieved 1.4-4.8 times greater mechanical stability in the humerus than in the tibia despite morphology that indicated translational feasibility. To better understand this discrepancy, finite element analyses (FEAs) modeled the implantation of the PODS into the bones. Models from cadaveric humeri (n = 3) and tibia (n = 3) were constructed from CT scans, and virtual implantation preparation of an array of endoprosthesis sizes that made contact with the endosteal surface but did not penetrate the outer cortex was performed. Final impaction of the endoprosthesis was simulated using a displacement ramp function to press the endoprosthesis model into the bone. Impaction force and maximum first principal (circumferential) stress were recorded to estimate stability and assess fracture risk of the system. We hypothesized that the humerus and tibia would have different optimal PODS sizing criteria that maximized impaction force and minimized first principal stress. The optimal sizing for the humerus corresponded to implantation instructions, whereas for the tibia optimal sizing was three times larger than the guidelines indicated. This FEA examination of impaction force and stress distribution lead us to believe that the same endoprosthesis strategy for the humerus is not suitable for the tibia because of thin medial and lateral cortices that compromise implantation.

Load applied on osseointegrated implant by transfemoral bone-anchored prostheses fitted with state-of-the-art prosthetic components

BACKGROUND

This study presented the load profile applied on transfemoral osseointegrated implants by bone-anchored prostheses fitted with state-of-the-art ÖSSUR microprocessor-controlled Rheo Knee XC and energy-storing-and-returning Pro-Flex XC or LP feet during five standardized daily activities.

METHODS

This cross-sectional cohort study included 13 participants fitted with a press-fit transfemoral osseointegrated implant. Loading data were directly measured with the tri-axial transducer of an iPecsLab (RTC Electronics, USA) fitted between the implant and knee unit. The loading profile was characterized by spatio-temporal gaits variables, magnitude of loading boundaries as well as onset and magnitude of loading extrema during walking, ascending and descending ramp and stairs.

FINDINGS

A total of 2127 steps was analysed. The cadence ranged between 36 ± 7 and 47 ± 6 strides/min. The absolute maximum force and moments applied across all activities was 1322 N, 388 N and 133 N as well as 22 Nm, 52 Nm and 88 Nm on and around the long, anteroposterior and mediolateral axes of the implant, respectively.

INTERPRETATION

This study provided new benchmark loading data applied by transfemoral bone-anchored prostheses fitted with selected ÖSSUR state-of-the-art components. Outcomes suggested that such prostheses can generate relevant loads at the interface with the osseointegrated implant to restore ambulation effectively. This study is a worthwhile contribution toward a systematic recording, analysis, and reporting of ecological prosthetic loading profiles as well as closing the evidence gaps between prescription and biomechanical benefits of state-of-the-art components. Hopefully, this will contribute to improve outcomes for growing number of individuals with limb loss opting for bionic solutions.

The bone anchored prostheses for amputees - Historical development, current status, and future aspects

In the past 50 years, bone anchored prostheses have evolved from a concept for experimental treatment to a rapidly developing area in orthopedics and traumatology. Up to date, there are dozens of centers in the world providing osseointegration amputation reconstructions and more than a thousand patients using the bone anchored prostheses. Compared with conventional socket prostheses, the bone anchored prosthesis by osseointegration avoids the debilitating problems related with soft tissues. It also provides physiological weight bearing, improved range of motion, and sensory feedback, all of which contribute to the improvement on quality of life for amputees. The present article briefly reviews the historical development of osseointegration surgery for amputation reconstruction and the current challenges. The implant design characters and surgical techniques of the two types of implants; the screw-type implant (presented by the OPRA system), and the press-fit implants (presented by EEP and OPL systems) are described. The major complications, infections and mechanical failures, are discussed in detail based on the latest evidence. Future aspects and experimental trials aiming to overcome the current challenges are presented.

Individual muscle contributions to hip joint-contact forces during walking in unilateral transfemoral amputees with osseointegrated prostheses

Direct skeletal attachment of prostheses in transfemoral amputees circumvents skin-interface complications associated with conventional sockets; however, joint pain and musculoskeletal disease is known to occur postoperatively. This study quantified hip contact forces and the roles of individual muscles in producing hip contact forces during walking in transfemoral amputees with osseointegrated prostheses. Musculoskeletal models were developed for four transfemoral amputees. Gluteus maximus and gluteus medius were the major contributors to the hip contact forces, and the intact limb hip muscles demonstrated greater contributions to hip contact forces than those of the residual limb. The findings may be useful for mitigating walking asymmetry.