Advanced thermal insulation and absorption properties of recycled cellulose aerogels

Advances in regenerated cellulosic aerogel from waste cotton textile for emerging multidimensional applications

Rapid development of society and the improvement of people's living standards have stimulated people's keen interest in fashion clothing. This trend has led to the acceleration of new product innovation and the shortening of the lifespan for cotton fabrics, which has resulting in the accumulation of waste cotton textiles. Although cotton fibers can be degraded naturally, direct disposal not only causes a serious resource waste, but also brings serious environmental problems. Hence, it is significant to explore a cleaner and greener waste textile treatment method in the context of green and sustainable development. To realize the high-value utilization of cellulose II aerogel derived from waste cotton products, great efforts have been made and considerable progress has been achieved in the past few decades. However, few reviews systematically summarize the research progress and future challenges of preparing high-value-added regenerated cellulose aerogels via dissolving cotton and other cellulose wastes. Therefore, this article reviews the regenerated cellulose aerogels obtained through solvent methods, summarizes their structure, preparation strategies and application, aimed to promote the development of the waste textile industry and contributed to the realization of carbon neutrality.

Tailoring hierarchical structures in cellulose carbon aerogels from sugarcane bagasse using different crosslinking agents for enhancing electrochemical desalination capability

Sugarcane bagasse is one of the most common Vietnamese agricultural waste, which possesses a large percentage of cellulose, making it an abundant and environmentally friendly source for the fabrication of cellulose carbon aerogel. Herein, waste sugarcane bagasse was used to synthesize cellulose aerogel using different crosslinking agents such as urea, polyvinyl alcohol (PVA) and sodium alginate (SA). The 3D porous network of cellulose aerogels was constructed by intermolecular hydrogen bonding, which was confirmed by Fourier transform infrared (FTIR), X-ray diffraction (XRD), scanning electron microscopy (SEM) and nitrogen adsorption/desorption. Among the three cellulose aerogel samples, cellulose - SA aerogel (SB-CA-SA) has low density of 0.04 g m-3 and high porosity of 97.38%, leading to high surface area of 497.9 m2 g-1 with 55.67% micropores of activated carbon aerogel (SB-ACCA-SA). The salt adsorption capacity was high (17.87 mg g-1), which can be further enhanced to 31.40 mg g-1 with the addition of CNT. Moreover, the desalination process using the SB-ACCA-SA-CNT electrode was stable even after 50 cycles. The results show the great combination of cellulose from waste sugarcane bagasse with sodium alginate and carbon nanotubes in the fabrication of carbon materials as the CDI-utilized electrodes with high desalination capability and good durability.

Solid Wood Modification toward Anisotropic Elastic and Insulative Foam-Like Materials

The methods used to date to produce compressible wood foam by top-down approaches generally involve the removal of lignin and hemicelluloses. Herein, we introduce a route to convert solid wood into a super elastic and insulative foam-like material. The process uses sequential oxidation and reduction with partial removal of lignin but high hemicellulose retention (process yield of 72.8%), revealing fibril nanostructures from the wood's cell walls. The elasticity of the material is shown to result from a lamellar structure, which provides reversible shape recovery along the transverse direction at compression strains of up to 60% with no significant axial deformation. The compressibility is readily modulated by the oxidation degree, which changes the crystallinity and mobility of the solid phase around the lumina. The performance of the highly resilient foam-like material is also ascribed to the amorphization of cellulosic fibrils, confirmed by experimental and computational (molecular dynamics) methods that highlight the role of secondary interactions. The foam-like wood is optionally hydrophobized by chemical vapor deposition of short-chained organosilanes, which also provides flame retardancy. Overall, we introduce a foam-like material derived from wood based on multifunctional nanostructures (anisotropically compressible, thermally insulative, hydrophobic, and flame retardant) that are relevant to cushioning, protection, and packaging.

Construction of Super-Hydrophobic Lignocellulosic Nanofibrils Aerogels as Speedy Oil Absorbents

Lignocellulosic nanofibrils (LCNF) aerogels have a three-dimensional structure, with large specific surface area, low density, which is promising to be developed into a new type of adsorbent with high absorption capacity. However, LCNF aerogels have the problem of simultaneous oil and water adsorption. This high hydrophilicity directly leads to low adsorption efficiency in oil-water systems. This paper suggests a facile and economical method for the synthesis of biocompatible CE-LCNF aerogels using LCNF and Castor oil triglycidyl ether (CE) was successfully established. The use of LCNF enabled aerogels to possess remarkably uniform pore size and structural integrity, while the introduction of hydrophobic silica produced stable superhydrophobicity for more than 50 days at room temperature. These aerogels presented desirable hydrophobicity (131.6°), excellent oil adsorption capacity (62.5 g/g) and excellent selective sorption property, making them ideal absorbents for oil spill cleaning. The effects of ratios of LCNF to CE composition, temperatures and oil viscosity on the oil adsorption performance of aerogels were estimated. The results displayed that the aerogels had the maximum adsorption capacity at 25 °C. The pseudo-secondary model had higher validity in oil adsorption kinetic theories compared to the pseudo-first-order model. The CE-LCNF aerogels were excellent super-absorbents for oil removal. Moreover, the LCNF was renewable and nontoxic, which has the potential to promote environmental applications.

Incorporation of Cellulose-Based Aerogels into Textile Structures

Given their exceptional attributes, aerogels are viewed as a material with immense potential. Being a natural polymer, cellulose offers the advantage of being both replenishable and capable of breaking down naturally. Cellulose-derived aerogels encompass the replenish ability, biocompatible nature, and ability to degrade naturally inherent in cellulose, along with additional benefits like minimal weight, extensive porosity, and expansive specific surface area. Even with increasing appreciation and acceptance, the undiscovered possibilities of aerogels within the textiles sphere continue to be predominantly uninvestigated. In this context, we outline the latest advancements in the study of cellulose aerogels' formulation and their diverse impacts on textile formations. Drawing from the latest studies, we reviewed the materials used for the creation of various kinds of cellulose-focused aerogels and their properties, analytical techniques, and multiple functionalities in relation to textiles. This comprehensive analysis extensively covers the diverse strategies employed to enhance the multifunctionality of cellulose-based aerogels in the textiles industry. Additionally, we focused on the global market size of bio-derivative aerogels, companies in the industry producing goods, and prospects moving forward.

A review on recent advances towards sustainable development of bio-inspired agri-waste based cellulose aerogels

Cellulose aerogel (CA) is considered to be the most promising material due to its extraordinary properties like unique microstructure, porosity, large specific surface area, biodegradability, renewable nature and lightweight. Cellulosic aerogels are thus found to have potential applications in different fields especially in water purification and biomedical field. Agricultural waste based cellulose aerogels are recently getting wider attention owing to its sustainability. The synthesis methods of agri-waste based cellulose aerogels, its properties and application in different fields especially in the field of water purification are detailed in a comprehensive manner. This review tries to bring light into the commercialization of value-added products from sustainable, cheap agricultural waste material and tries to motivate young researchers.

Cellulose nanofiber/MXene/luffa aerogel for all-weather and high-efficiency cleanup of crude oil spills

The remediation of heavy crude oil spills is a global challenge because frequent crude oil spills cause long-term damage to local living beings and marine ecosystems. Herein, a solar-driven and Joule-driven self-heated aerogel were developed as an all-weather adsorbent to efficiently absorb crude oil by obviously decreasing the viscosity of crude oil. The cellulose nanofiber (CNF)/MXene/luffa (CML) aerogel was fabricated via a simple freeze-drying method using CNF, MXene, and luffa as raw materials, and then coated with a layer of polydimethylsiloxane (PDMS) to make it hydrophobic and further increase oil-water selectivity. The aerogel can quickly reach 98 °C under 1 sun (1.0 kW/m²), which remains saturated temperature after 5 times photothermal heating/cooling cycles, indicating that the aerogel has great photothermal conversation capability and stability. Meanwhile, the aerogel can also rapidly rise to 110.8 °C with a voltage of 12 V. More importantly, the aerogel achieved the highest temperature of 87.2 °C under outdoor natural sunlight, providing a possibility for promising applications in practical situations. The remarkable heating capability enables the aerogel to decrease the viscosity of crude oil substantially and increase the absorption rate of crude oil by the physical capillary action. The proposed all-weather aerogel design provides a sustainable and promising solution for cleaning up crude oil spills.

Insights on Some Polysaccharide Gel Type Materials and Their Structural Peculiarities

Global resources have to be used in responsible ways to ensure the world's future need for advanced materials. Ecologically friendly functional materials based on biopolymers can be successfully obtained from renewable resources, and the most prominent example is cellulose, the well-known most abundant polysaccharide which is usually isolated from highly available biomass (wood and wooden waste, annual plants, cotton, etc.). Many other polysaccharides originating from various natural resources (plants, insects, algae, bacteria) proved to be valuable and versatile starting biopolymers for a wide array of materials with tunable properties, able to respond to different societal demands. Polysaccharides properties vary depending on various factors (origin, harvesting, storage and transportation, strategy of further modification), but they can be processed into materials with high added value, as in the case of gels. Modern approaches have been employed to prepare (e.g., the use of ionic liquids as "green solvents") and characterize (NMR and FTIR spectroscopy, X ray diffraction spectrometry, DSC, electronic and atomic force microscopy, optical rotation, circular dichroism, rheological investigations, computer modelling and optimization) polysaccharide gels. In the present paper, some of the most widely used polysaccharide gels will be briefly reviewed with emphasis on their structural peculiarities under various conditions.

Optimization of the Sound Absorption Coefficient (SAC) from Cellulose-Silica Aerogel Using the Box-Behnken Design

Noise pollution, which has become a major environmental issue in urban areas, can be minimized using acoustic insulation derived from cellulose-silica aerogel. The raw materials required in the process include waste newspaper-based cellulose, geothermal silica, and NaOH/ZnO solution. Therefore, this study investigates the effect of cellulose, silica, and ZnO concentrations on optimizing the sound absorption coefficient (SAC) using the Box-Behnken design (BBD). The results showed that the optimum conditions were obtained at 39.8578 wt % cellulose, 16.5428 wt % silica, and 0.5684 wt % ZnO. The impedance test for the cellulose aerogel and cellulose-silica aerogel showed SAC values of 0.59 and 0.70, respectively, and were characterized by XRD, FTIR, BET-BJH, SEM-EDX, and TG. The results of XRD and FTIR data indicate that the product was cellulose-silica aerogel, and the SEM micrographs showed that silica particles were attached to the fiber surface. Furthermore, type IV isotherms were observed in the cellulose-silica aerogel, typical of mesoporous materials. The presence of silica strengthened the aerogel structure, improved its thermal stability, and increased the surface area but decreased its pore size.

Sustainable Reuse of Waste Tire Textile Fibers (WTTF) as Reinforcements

Waste tire textile fibers (WTTF), as a by-product (10–15% by weight of tires) of end-of-life tires (ELT) mechanical recycling (grinding), are classified as hazardous wastes and traditionally burnt (thermal recycling) or buried (landfilling), leading to several environmental and ecological issues. Thus, WTTF still represent an important challenge in today’s material recycling streams. It is vital to provide practical and economical solutions to convert WTTF into a source of inexpensive and valuable raw materials. In recent years, tire textile fibers have attracted significant attention to be used as a promising substitute to the commonly used natural/synthetic reinforcement fibers in geotechnical engineering applications, construction/civil structures, insulation materials, and polymer composites. However, the results available in the literature are limited, and practical aspects such as fiber contamination (~65% rubber particles) remain unsolved, limiting WTTF as an inexpensive reinforcement. This study provides a comprehensive review on WTTF treatments to separate rubber and impurities and discusses potential applications in expansive soils, cement and concrete, asphalt mixtures, rubber aerogels and polymer composites.

Advanced cellulose nanocrystals (CNC) and cellulose nanofibrils (CNF) aerogels: Bottom-up assembly perspective for production of adsorbents

The most common and abundant polymer in nature is the linear polysaccharide cellulose, but processing it requires a new approach since cellulose degrades before melting and does not dissolve in ordinary organic solvents. Cellulose aerogels are exceptionally porous (>90 %), have a high specific surface area, and have low bulk density (0.0085 mg/cm³), making them suitable for a variety of sophisticated applications including but not limited to adsorbents. The production of materials with different qualities from the nanocellulose based aerogels is possible thanks to the ease with which other chemicals may be included into the structure of nanocellulose based aerogels; despite processing challenges, cellulose can nevertheless be formed into useful, value-added products using a variety of traditional and cutting-edge techniques. To improve the adsorption of these aerogels, rheology, 3-D printing, surface modification, employment of metal organic frameworks, freezing temperature, and freeze casting techniques were all investigated and included. In addition to exploring venues for creation of aerogels, their integration with CNC liquid crystal formation were also explored and examined to pursue "smart adsorbent aerogels". The objective of this endeavour is to provide a concise and in-depth evaluation of recent findings about the conception and understanding of nanocellulose aerogel employing a variety of technologies and examination of intricacies involved in enhancing adsorption properties of these aerogels.

Roadmap to sustainable plastic waste management: a focused study on recycling PET for triboelectric nanogenerator production in Singapore and India

This study explores the implications of plastic waste and recycling management on recyclates for manufacturing clean-energy harvesting devices. The focus is on a comparative analysis of using recycled polyethylene terephthalate (PET) for triboelectric nanogenerator (TENG) production, in two densely populated Asian countries of large economies, namely Singapore and India. Of the total 930,000 tonnes of plastic waste generated in Singapore in 2019, only 4% were recycled and the rest were incinerated. In comparison, India yielded 8.6 million tonnes of plastic waste and 70% were recycled. Both countries have strict recycling goals and have instituted different waste and recycling management regulations. The findings show that the waste policies and legislations, responsibilities and heterogeneity in collection systems and infrastructure of the respective country are the pivotal attributes to successful recycling. Challenges to recycle plastic include segregation, adulterants and macromolecular structure degradation which could influence the recyclate properties and pose challenges for manufacturing products. A model was developed to evaluate the economic value and mechanical potential of PET recyclate. The model predicted a 30% loss of material performance and a 65% loss of economic value after the first recycling cycle. The economic value depreciates to zero with decreasing mechanical performance of plastic after multiple recycling cycles. For understanding how TENG technology could be incorporated into the circular economy, a model has estimated about 20 million and 7300 billion pieces of aerogel mats can be manufactured from the PET bottles disposed in Singapore and India, respectively which were sufficient to produce small-scale TENG devices for all peoples in both countries.

Bio-Based Hydrogel and Aerogel Composites Prepared by Combining Cellulose Solutions and Waterborne Polyurethane

Hydrogel composites can be prepared from cellulose-based materials and other gel materials, thus combining the advantages of both kinds of material. The aerogel, porous material formed after removing the water in the hydrogel, can maintain the network structure. Hydrogel and aerogel have high application potential. However, low mechanical strength and weight loss of cellulose hydrogel due to the water dehydration/absorption limit the feasibility of repeated use. In this study, cellulose hydrogels were prepared using microcrystalline cellulose (MC), carboxymethyl cellulose (CMC), and hydroxyethyl cellulose (HEC) as raw materials. Waterborne polyurethane (WPU) was added during the preparation process to form cellulose/WPU composite hydrogel and aerogel. The influence of the cellulose type and WPU addition ratio on the performance of hydrogel and aerogel were investigated. The results show that the introduction of WPU can help strengthen and stabilize the structure of cellulose hydrogel, reduce weight loss caused by water absorption and dehydration, and improve its reusability. The mixing of cellulose and WPU at a weight ratio of 90/10 is the best ratio to make the cellulose/WPU composite aerogel with the highest water swelling capacity and heat resistance.

Utilization of Cellulose to Its Full Potential: A Review on Cellulose Dissolution, Regeneration, and Applications

As the most abundant natural polymer, cellulose is a prime candidate for the preparation of both sustainable and economically viable polymeric products hitherto predominantly produced from oil-based synthetic polymers. However, the utilization of cellulose to its full potential is constrained by its recalcitrance to chemical processing. Both fundamental and applied aspects of cellulose dissolution remain active areas of research and include mechanistic studies on solvent-cellulose interactions, the development of novel solvents and/or solvent systems, the optimization of dissolution conditions, and the preparation of various cellulose-based materials. In this review, we build on existing knowledge on cellulose dissolution, including the structural characteristics of the polymer that are important for dissolution (molecular weight, crystallinity, and effect of hydrophobic interactions), and evaluate widely used non-derivatizing solvents (sodium hydroxide (NaOH)-based systems, N,N-dimethylacetamide (DMAc)/lithium chloride (LiCl), N-methylmorpholine-N-oxide (NMMO), and ionic liquids). We also cover the subsequent regeneration of cellulose solutions from these solvents into various architectures (fibers, films, membranes, beads, aerogels, and hydrogels) and review uses of these materials in specific applications, such as biomedical, sorption, and energy uses.

Synthesis and performance evaluation of plastic waste aerogel as sustainable and reusable oil absorbent

Direct utilization of waste polyethylene terephthalate (PET) from the environment to form highly porous aerogel technology for oil absorption is an attractive approach from the view point of green chemistry. However, the oil absorption reaction is limited by low oil absorption capacity and less stability. For now, silica aerogel are used to solve these problem. Our goal is to substitute to these silica aerogel with PET aerogel technology. Herein, we have prepared an environmental waste PET based aerogel with 1.0:0.5 wt% PET, polyvinyl alcohol (PVA), and glutaraldehyde (GA) 0.2% v/v were dispersed in 10 mL DI water, followed by homogenization (30 min), sonication (10 min), and ageing (2 h) at 70 °C. To escape macroscopic cracking, cooling (8 h) at 4 °C was followed by freezing (6 h), freeze drying at -80 °C, and 5 mTorr for 18 h. The hybrid PET aerogel displays excellent performance towards oil absorption. Notably it showed high absorption capacity towards the different oils about 21-40 times its own weight, depending on the viscosity and density of the oil and solvents within 15-35 s, 25 °C, and 2 × 2 cm aerogel size. In addition, the aerogel shows there is no change in structure after several recycles due to high mechanical strength. Furthermore, because of the PET aerogel's high porosity (99.74%) and low density (0.0311 g/cm³), close bonding between PET-PVA occurs. Therefore, aerogel shows hydrophobic nature, good mechanical strength, high thermal stability, arrangement of the interconnected fibrillar pore network offers a high surface to volume ratio, low surface energy, high surface roughness, and more reusability. All these parameters are responsible for high oil absorption.

Directional, super-hydrophobic cellulose nanofiber/polyvinyl alcohol/montmorillonite aerogels as green absorbents for oil/water separation

Nowadays, the problem of oil spill and organic solvent pollution has become more and more serious, and developing a green and efficient treatment method has become a research hotspot. Herein, the preparation of porous super‐hydrophobic aerogel by directional freezing with cellulose nanofibre (CNF) as the base material, polyvinyl alcohol (PVA) as the cross‐linking agent and montmorillonite (MMT) as the modifier and filler, followed by hydrophobic treatment with chemical vapour deposition is reported. The prepared composite aerogel presented three‐dimensional inter‐perforation network structure, low density (26.52 mg⋅cm⁻³), high porosity (96.1 %) and good hydrophobicity (water contact angle of 140°). Notably, the composite aerogel has a good adsorption effect on different oils and organic solutions, and its adsorption capacity can reach 40–68 times of its initial weight. After complete adsorption, the aerogel could be easily collected. More importantly, the composite aerogel had high strength, whose compressive stress at 70 % strain reached 0.15 MPa and could bear over 1290 times its weight without deformation after 2 weeks. A new, green, simple and efficient absorbent for the adsorption of oils and organic solvents is provided.

Hydrophobic composite foams based on nanocellulose-sepiolite for oil sorption applications

TEMPO (2,2,6,6-tetramethylpiperidin-1-oxyl)-oxidized cellulose nanofibers (CNF) were assembled to fibrous clay sepiolite (SEP) by means of a high shear homogenizer and an ultrasound treatment followed by lyophilization using three different methods: normal freezing, directional freezing, and a sequential combination of both methods. Methyltrimethoxysilane (MTMS) was grafted to the foam surface by the vapor deposition method to introduce hydrophobicity to the resulting materials. Both the SEP addition (for the normal and directional freezing methods) and the refreezing preparation procedure enhanced the compressive strength of the foams, showing compressive moduli in the range from 28 to 103 kPa for foams loaded with 20% w/w sepiolite. Mercury intrusion porosimetry shows that the average pore diameters were in the range of 30-45 µm depending on the freezing method. This large porosity leads to materials with very low apparent density, around 6 mg/cm³, and very high porosity >99.5%. In addition, water contact angle measurement and Fourier-transform infrared spectroscopy (FTIR) were applied to confirm the foam hydrophobicity, which is suitable for use as an oil sorbent. The sorption ability of these composite foams has been tested using olive and motor oils as models of organophilic liquid adsorbates, observing a maximum sorption capacity of 138 and 90 g/g, respectively.

Current Status of Cellulosic and Nanocellulosic Materials for Oil Spill Cleanup

Recent developments in the application of lignocellulosic materials for oil spill removal are discussed in this review article. The types of lignocellulosic substrate material and their different chemical and physical modification strategies and basic preparation techniques are presented. The morphological features and the related separation mechanisms of the materials are summarized. The material types were classified into 3D-materials such as hydrophobic and oleophobic sponges and aerogels, or 2D-materials such as membranes, fabrics, films, and meshes. It was found that, particularly for 3D-materials, there is a clear correlation between the material properties, mainly porosity and density, and their absorption performance. Furthermore, it was shown that nanocellulosic precursors are not exclusively suitable to achieve competitive porosity and therefore absorption performance, but also bulk cellulose materials. This finding could lead to developments in cost- and energy-efficient production processes of future lignocellulosic oil spillage removal materials.

Multifunctional cellulosic aerogels from Posidonia oceanica waste biomass with antioxidant properties for meat preservation

Posidonia oceanica waste biomass has been valorized to develop bioactive multifunctional cellulosic aerogels (HCAG) by simpler and greener protocols. Hydrophobization of cellulosic aerogels was achieved through PLA coating, while bioactivity was imparted by the incorporation of hydrophilic (E2) and hydrophobic extracts (E3) produced from the same biomass. The incorporation of extracts led to denser aerogels, with less porous structures. These aerogels showed outstanding water and oil sorption capacities (1500-1900%), being able to release the adsorbed liquid almost completely after 7 days. Interestingly, all the aerogels showed a positive inhibition effect (23-91%) on the β-carotene bleaching assay. Moreover, the aerogels loaded with extracts, especially when combining E2 and E3, were able to reduce the oxidation of lipids and oxymyoglobin in red meat after 10 days of storage. This evidences the potential of these multifunctional aerogels as bioactive adsorbing pads to preserve the quality of fresh packaged foods.

Thermally Insulating Nanocellulose-Based Materials

Thermally insulating materials based on renewable nanomaterials such as nanocellulose could reduce the energy consumption and the environmental impact of the building sector. Recent reports of superinsulating cellulose nanomaterial (CNM)-based aerogels and foams with significantly better heat transport properties than the commercially dominating materials, such as expanded polystyrene, polyurethane foams, and glass wool, have resulted in a rapidly increasing research activity. Herein, the fundamental basis of thermal conductivity of porous materials is described, and the anisotropic heat transfer properties of CNMs and films with aligned CNMs and the processing and structure of novel CNM-based aerogels and foams with low thermal conductivities are presented and discussed. The extraordinarily low thermal conductivity of anisotropic porous architectures and multicomponent approaches are highlighted and related to the contributions of the Knudsen effect and phonon scattering.

Polysaccharide-based aerogels for thermal insulation and superinsulation: An overview

To reduce energy losses due to the insufficient thermal insulation is one of the current "hot" topics. Various commercial porous materials are used with the best conductivity around 0.03-0.04 W/(m·K). Aerogels are the only known materials with "intrinsic" thermal superinsulating properties, i.e. with thermal conductivity below that of air in ambient conditions (0.025 W/(m·K)). The classical thermal superinsulating aerogels are based on silica and some synthetic polymers, with conductivity 0.014-0.018 W/(m·K). Aerogels based on natural polymers are new materials created at the beginning of the 21st century. Can bio-aerogels possess thermal superinsulating properties? What are the bottlenecks in the development of bio-aerogels as new high-performance thermal insulationing materials? We try to answer these questions by analyzing thermal conductivity of bio-aerogels reported in literature.

A novel aerogel from thermal power plant waste for thermal and acoustic insulation applications

Massive quantities of fly ash are produced worldwide from thermal power plants, posing a serious environmental threat due to their storage and disposal problems. In this study, for the first time, fly ash is converted into an advanced and novel aerogel through a green and eco-friendly process. The developed aerogel has a low density of 0.10-0.19 g cm^-3, a high porosity of up to 90%, a low thermal conductivity of 0.042-0.050 W/mK, and a good sound absorption coefficient (noise reduction coefficient [NRC] value of 0.20-0.30). It also shows a high compressive Young's modulus of up to 150 kPa. Therefore, the newly developed fly ash aerogel is a potential material for thermal and acoustic insulation applications, along with lightweight composites in automotive and aerospace applications.

Nanocellulose-based foam morphological, mechanical and thermal properties in relation to hydrogel precursor structure and rheology

Foams were prepared from nanocellulose-based hydrogel precursors using a freeze-drying process. The work mainly aims at investigating the relationships between the mechanical and thermal properties of foams and the rheological properties of their hydrogel precursors, which were characterized in a previous paper. The structure of foams was characterized by SEM and confocal microscopy, their elasticity by compression tests, and their thermal conductivity by hot strip as well as transient pulsed techniques. A strong correlation was shown between the elastic properties of foams and those of their hydrogel precursors, and a minimum thermal conductivity was shown to appear at a cellulose volume fraction corresponding to a transition in viscoelastic properties of hydrogels. Results suggest that foams and hydrogels share common microstructural features, which makes it possible to tune the mechanical and thermal properties of foams by tuning the rheological properties of their hydrogel precursors.

Production of Bacterial Cellulose Aerogels With Improved Physico-Mechanical Properties and Antibacterial Effect

Aerogels have gained significant interest in recent decades because of their unique properties such as high porosity, low density, high surface area, and excellent heat and noise insulation. However, their high cost and low mechanical strength limit their practical application. We developed appropriate conditions to produce aerogels with controlled density, high mechanical strength, and thermal characteristics from bacterial cellulose (BC) synthesized by the strain Komagataeibacter sucrofermentans H-110. Aerogels produced using TEMPO oxidized BC (OBC) exhibited high mechanical strength and lower shrinkage than those from native bacterial cellulose (NBC). Compared to the NBC, the use of TEMPO-oxidized BC with oxidation degrees (OD) of 1.44 and 3.04% led to the reduction of shrinkage of the aerogels from 41.02 to 17.08%. The strength of the aerogel produced from the TEMPO-oxidized BC with an oxidation degree of 1.44% was twice that of the aerogel produced from NBC. The addition of Mg²⁺ at concentrations of 20 and 40 mM during the preparation of the aerogels increased the strength of the aerogels by 4.9 times. The combined use of TEMPO-oxidized BC and Mg²⁺ allowed pore size reduction from 1,375 to 197.4 μm on the outer part of the aerogels, thereby decreasing the thermal conductivity coefficient from 0.036 to 0.0176 W/(m•K). Furthermore, novel biocomposites prepared from the aerogels based on NBC and OBC and sodium fusidate, which have high antibiotic activity against Staphylococcus aureus, were obtained. Owing to their antibacterial properties, these aerogels can be used as functional biomaterials in a wide range of applications such as in tissue engineering and fabrication of wound dressing materials.

Functional wastepaper-montmorillonite composite aerogel for Cd2+ adsorption

In this study, a composite aerogel (WP-MMT) composed of wastepaper (WP) and montmorillonite (MMT) was prepared by ambient pressure drying technology to adsorb Cd²⁺. The study of compression performance indicated that the composite aerogel had ideal mechanical strength when the mass ratio of WP to MMT was 1:1. The specific surface areas of the aerogels modified by hydrogen peroxide (WP-MMT-H₂O₂) and sodium hydroxide (WP-MMT-NaOH) were increased greatly. The sorption isotherms and kinetics of Cd²⁺ sorption on WP-MMT-H₂O₂ and WP-MMT-NaOH were investigated. The Cd²⁺ sorption data could be well described by a simple Langmuir model, and the pseudo-second-order kinetic model best fitted the kinetic data. The maximum sorption capacity obtained from the Langmuir model was 232.50 mg/g for WP-MMT-NaOH. The adsorption mechanism of WP-MMT was chemical adsorption of a single-molecule layer. In general, it was proved that the composite aerogel with high adsorption capacity of Cd²⁺ could be synthesized from modified WP and MMT by ambient pressure drying. The composite aerogel fabricated by wastepaper and montmorillonite showed bright application prospect in the aqueous heavy metal pollution control.

Compostable, fully biobased foams using PLA and micro cellulose for zero energy buildings

Ecological, health and environmental concerns are driving the need for bio-resourced foams for the building industry. In this paper, we examine foams made from polylactic acid (PLA) and micro cellulose fibrils (MCF). To ensure no volatile organic compounds in the foam, supercritical CO₂ (sc-CO₂) physical foaming of melt mixed systems was conducted. Mechanical and thermal conductivity properties were determined and applied to a net zero energy model house. The results showed that MCF had a concentration dependent impact on the foams. First structurally, the presence of MCF led to an initial increase followed by a decrease of open porosity, higher bulk density, lower expansion ratios and cell size. Differential Scanning Calorimetry and Scanning Electron Microscopy revealed that MCF decreased the glass transition of PLA allowing for a decrease in cell wall thickness when MCF was added. The mechanical performance initially increased with MCF and then decreased. This trend was mimicked by thermal insulation which initially improved. Biodegradation tests showed that the presence of cellulose in PLA improved the compostability of the foams. A maximum comparative mineralization of 95% was obtained for the PLA foam with 3 wt.% MCF when expressed as a fractional percentage of the pure cellulose reference. Energy simulations run on a model house showed that relative to an insulation of polyurethane, the bio-resourced foams led to no more than a 12% increase in heating and cooling. The energy efficiency of the foams was best at low MCF fractions.

Biomass-Derived, Water-Induced Self-Recoverable Composite Aerogels with Robust Superwettability for Water Treatment

Polluted water is a worldwide problem; therefore, effective separation of oil/water and removal of dyes, organic micropollutants, and heavy metals in wastewater are the need of the hour. Herein, hydrophilic β-cyclodextrin-grafted carboxymethyl cellulose, biodegradable polyvinyl alcohol, and chitosan were used as main raw materials to construct a multifunctional aerogel framework by simple sol-gel and directional freeze-drying methods. Featuring intrinsic superamphiphilic wettability in air, robust superoleophobic wettability underwater, and excellent shape-recovery characteristics, the biomass-derived aerogel presents durable oil/water separation even after 10 cycles. The aerogels possess prominent adsorption capacity for methyl blue, 1-naphthylamine, and Cu²⁺, which was as high as 121.55 mg/g, 33.96 mg/g, and 122.6 mg/g, respectively. In addition, various pollutant mixtures could be effectively adsorbed by the aerogel at the same time with the adsorption capacity of 121.75 mg/g for methyl blue, 0.97 mg/g for bisphenol A, and 20.11 mg/g for Cu²⁺.

Production of starch aerogel in form of monoliths and microparticles

Pea and amylomaize starches were used to produce aerogel in form of monoliths and microparticles. The formation of starch gel was investigated, and we showed that each starch needed a different pasting temperature for its complete dissolution. The gelation kinetics was investigated with oscillatory rheometry for both systems as a function of the starch concentration. The gelation and retrogradation temperature of the starch gel were varied and its impact on the final aerogel evaluated. The emulsion gelation was carried out batch wise in a stirred vessel with different impeller geometries, concentrations of surfactant (Span80 and PGPR) and stirring rates. A particle size prediction approach based on idealized flow (Couette, 2D hyperbolic and turbulent) during the emulsification was proposed. A semi-continuous set-up for the emulsion gelation was developed in which the emulsification occurs in a single pass through a colloid mill and the gelation is triggered in-line with a counter-current heat exchanger.

Use of municipal, agricultural, industrial, construction and demolition waste in thermal and sound building insulation materials: a review article

Production and usage of green and sustainable building materials realizes the desire to integrate more biodegradable, natural, recycled, and renewable resources into the construction industry. The aim is to replace traditionally available construction industry materials due to their environmental impacts through air emissions and waste generation. An observed trend is the production of insulation materials by recycling of industrial, agriculture, construction and demolition (C&D), and municipal solid wastes, thus reducing the environmental burdens of these wastes. While thermal insulation is important in saving energy, sound insulation has drawn much attention in recent years. There are various waste materials that have good thermal and sound properties, enabling effective replacement of traditional materials. This review investigates the use of industrial, agricultural, C&D, and municipal solid wastes to produce innovative thermal and acoustic insulating building materials. The performance of these insulating materials, and the influence of several materials parameters (density, thermal conductivity, sound absorption coefficient) on thermal and acoustic performance are reported after a brief description of each material.

Fabrication and Properties of Hybrid Coffee-Cellulose Aerogels from Spent Coffee Grounds

A fully biodegradable hybrid coffee-cotton aerogel has been successfully developed from spent coffee grounds, 100% cotton fiber and polyvinyl alcohol (PVA) flakes via environmental friendly processes. The cotton fibers in coffee aerogel help to maintain the structure and improve the overall properties of the new hybrid coffee-cotton aerogel. The results show that increasing the concentration of fibers, while keeping the concentration of spent coffee grounds constant, the sinking of coffee ground particles in solution and shrinking effect on the aerogels are minimized and the overall mechanical and oil absorption properties are improved. The developed hybrid aerogels possess high porosity of 92-95% and super-hydrophobicity with an average water contact angle of 139°. Oil absorption capacity achieves 16 g/g with 0.50 wt.% of cotton fibers inside the coffee aerogel. Their thermal conductivity is in the range of 0.037-0.045 W/mK and compressive Young's modulus achieves highest at 15.6 kPa. The properties of the hybrid aerogel indicate it as a potential material in several applications such as thermal insulation, oil absorption and filtration.

ZCIS/ZnS QDs fluorescent aerogels with tunable emission prepared from porous 3D nanofibrillar bacterial cellulose

Bacterial cellulose (BC) features a nanofibrillar network structure that can provide a good template for quantum dots (QDs), to overcome the fluorescence quenching-effect of QDs in polymer composites. Here, we fabricated novel fluorescent aerogels with tunable emission by covalently binding environmentally-friendly ZnS(CuInS₂)/ZnS core-shell quantum dots along the nanofibrillar BC. A new ligand of 3-(mercaptopropyl)trimethoxysilane allows QDs to transfer from toluene to alcohol solvent and stably bind to the BC. After supercritical CO₂ drying, the resulting BC-QDs aerogels maintain the porous nanofibrillar morphology of BC with ultra-light-weight, the QDs are well-distributed along the BC fiber surfaces without aggregation. The emission wavelength can be tuned in a wide range from 470 to 750 nm by simply adjusting the QDs core component or shell layers. This work provides a new approach for fabricating QDs-polymer hydrogels and aerogels with well distributed QDs via chemical binding that potential as smart sensor, catalysis, and 3D display applications.

Recycled Cellulose Aerogels from Paper Waste for a Heat Insulation Design of Canteen Bottles

Exercising in a tropical climate with constant high temperatures and high humidity increases the risk of heatstroke for active people who frequently train outdoors. For these active persons, a cooling source of water nearby can be essential, and this is usually carried in canteen bottles. However, commercially available water canteen bottles have limited thermal insulation capability to keep the liquid content cooled for the required period. This work proposed an engineering solution to enhance the heat insulation performance of water canteen bottles, using recycled cellulose aerogels made from paper waste for the first time as an insulating layer. Recycled cellulose aerogels wrapped around the water canteen bottle provides excellent thermal insulation performance, while not adding significant weight to the bottle. The temperature of the ice slurry in the canteen bottle was measured periodically over four hours with a mercury thermometer. The effects of the static and dynamic conditions on the temperature rate were also quantified. A 1.5 cm thickness of 1.0 wt.% recycled cellulose aerogel wrapped around the canteen bottle can provide an excellent thermal insulation performance with the lowest rise in temperature, achieving a low final temperature of the ice slurry content of 3.5 °C after 4 h. This result is much better than that provided by available commercial bottles under the same conditions.

Preparation and Characterization of High Amylose Corn Starch⁻Microcrystalline Cellulose Aerogel with High Absorption

Microcrystalline cellulose (MCC) aerogels were synthesized, blendingwith high amylose corn starch of different contents based on a NaOH–urea solution, and following by vacuum freeze-drying technology. The microstructure of the aerogel was observed by scanning electron microscopy (SEM) as an interconnected, porous three-dimensional structure, while X-ray diffractogram (XRD) measurements showed that the crystalline form was converted from cellulose I to cellulose II during dissolution and regeneration. Thermogravimetric analysis (TGA) showed that the content of starch had little effect on the thermal stability of the aerogel, whereas the content of starch had great influences on absorption and viscoelastic properties. When the ratio of starch was 10% and 15%, the prepared aerogels presented a low density and abundant pores, which endowed the aerogels, not only with the highest absorption ratio of pump oil and linseed oil (10.63 and 11.44 g/g, respectively), but also with better dynamic viscoelastic properties.

Anisotropic Cellulose Nanofibers/Polyvinyl Alcohol/Graphene Aerogels Fabricated by Directional Freeze-drying as Effective Oil Adsorbents

Under the current situation of frequent oil spills, the development of green and recyclable high-efficiency oil-absorbing aerogel materials has attracted wide attention from researchers. In this study, we report a high-strength, three-dimensional hydrophobic cellulose nanofiber (CNF)/polyvinyl alcohol (PVA)/graphene oxide (GO) composite aerogel with an anisotropic porous structure, which was fabricated by directional freeze-drying technology using anisotropically grown ice crystals as a template, followed by hydrophobic treatment with a simple dip coating process. The prepared composite aerogel presented anisotropic multi-level pore microstructures, low density (17.95 mg/cm³) and high porosity (98.8%), good hydrophobicity (water contact angle of 142°) and great adsorption capacity (oil absorption reaching 96 times its own weight). More importantly, the oriented aerogel had high strength, whose compressive stress at 80% strain reached 0.22 MPa and could bear more than 22,123 times its own weight without deformation. Therefore, the CNF/PVA/GO composite aerogel prepared by a simple and easy-to-operate directional freeze-drying method is a promising absorbent for oil-water separation.

A Study of the Physical and Mechanical Properties of Aerogels Obtained from Bacterial Cellulose

Aerogels with a density of 4.2-22.8 kg/m³ were obtained from bacterial cellulose synthesized under static and dynamic cultivation conditions on a molasses medium. The strength properties and porous structure of the aerogels strongly depended on their density. With an aerogel density of 22.8 kg/m³, the modulus of elasticity at 80% compression of the sample was 0.1 MPa. The decrease in the density of aerogels led to an increase in the pore sizes ranging from 20 to 1000 μm and a decrease in the modulus of elasticity. These characteristics were more pronounced in aerogels obtained from bacterial cellulose under static cultivation conditions. The aerogels had a low coefficient of thermal conductivity (0.0257 W m^-1 °C^-1), which is comparable to the thermal conductivity of air, and moderate thermal stability because the degradation processes of the aerogels began at 237 °C. The aerogels obtained from bacterial cellulose had high sound absorption coefficients in the frequency range of 200-5000 Hz, which makes it possible to use the aerogels as heat- and sound-insulating materials.

Controllable synthesis of pomelo peel-based aerogel and its application in adsorption of oil/organic pollutants

Oil/water separation is a field of high significance as it might efficiently resolve the contamination of industrial oily wastewater and other oil/water pollution. In this paper, an environmentally-friendly hydrophobic aerogel with high porosity and low density was successfully synthesized with renewable pomelo peels (PPs) as precursors. Typically, a series of sponge aerogels (HPSA-0, HPSA-1 and HPSA-2) were facilely prepared via high-speed dispersion, freeze-drying and silanization with methyltrimethoxysilane. Indeed, the physical properties of aerogel such as density and pore diameter could be tailored by different additives (filter paper fibre and polyvinyl alcohol). Hence, their physico-chemical properties including internal morphology and chemical structure were characterized in detail by Fourier transform infrared, Brunauer-Emmett-Teller, X-ray diffraction, scanning electron microscope, Thermal gravimetric analyzer (TG) etc. Moreover, the adsorption capacity was further determined and the results revealed that the PP-based aerogels presented excellent adsorption performance for a wide range of oil products and/or organic solvents (crude oil 49.8 g g^-1, soya bean oil 62.3 g g^-1, chloroform 71.3 g g^-1 etc.). The corresponding cyclic tests showed the absorption capacity decreased slightly from 94.66% to 93.82% after 10 consecutive cycles, indicating a high recyclability.