Efficient acetaminophen removal from water and hospital effluents treatment by activated carbons derived from Brazil nutshells

Simulation of solar photocatalytic reactor with immobilized photocatalyst for degradation of pharmaceutical pollutants

This study focuses on the simulation of a solar photocatalytic reactor with linear parabolic reflectors and continuous fluid flow. The simulation approach was initially validated against experimental data reported by Miranda-Garcia et al. Catal Today 151:107-113 (2010), yielding a high degree of accuracy of approximately 0.99%. In this article, the effect of light intensity, Reynolds number, and fluid residence time on the performance of a photoreactor system using titanium dioxide catalyst and ibuprofen pollutant has been investigated. The results show that the intensity of light intensity has an effect of up to 29% on the decomposition of pollutant. With the increase of radiation intensity, the removal of pollutants reached from 85.5% to 99.46%. It has been demonstrated that higher flow turbulence significantly impacts removal efficiency, achieving rates of up to 71%. Moreover, enhancing the fluid's residence time through implementing a recirculating flow within the photoreactor has resulted in a 13% enhancement in removal efficiency. These results can be an important guide for optimizing the design of photocatalytic reactors. By adjusting the examined parameters, it is possible to obtain a higher efficiency in the removal of pollutants, which will be very effective in the scaling and industrial design of solar reactors.

Synthesis and characterization of a crosslinked deacetylated chitin modified chicken bone waste-derived hydroxyapatite and TiO2 biocomposite for defluoridation of drinking water

This work represents an innovative approach to the synthesis and characterization of a chitosan-based biocomposite for fluoride adsorption. The work involved the development of a biocomposite based on modified chicken bone waste-derived hydroxyapatite and TiO2. The composite was characterized using scanning electron microscopy with Energy Dispersive X-ray analysis (SEM-EDX), X-ray diffraction (XRD), Fourier-transform infrared analysis (FTIR), thermal-gravimetric analysis (TGA), and X-ray photoelectron spectroscopy (XPS). The optimum parameters for fluoride removal were determined, and the kinetic data was better fitted to the pseudo-first-order model. The Liu equations provided a better description of the experimental adsorption isotherm data. The adsorption mechanism and the interaction of the composite with fluoride were better understood using Density Functional Theory (DFT) calculations and Non-Covalent Interactions (NCI) analyses, paving the way for more effective and efficient defluoridation methods.

Competitive adsorption of acetaminophen and caffeine onto activated Tingui biochar: characterization, modeling, and mechanisms

Tingui biochar (TB) activated with potassium hydroxide (TB-KOH) was synthesized in the present study. The adsorption capacity of TB-KOH was evaluated for the removal of acetaminophen and caffeine in monocomponent and bicomponent solutions. As a result, the study of the TB-KOH characterization as well as the adsorption kinetics, isotherm, thermodynamics, and a suggestion of the global adsorption mechanism are presented. TB-KOH was characterized through physical-chemical analysis to understand its surface morphology and how it contributes to the adsorption of these drugs. Furthermore, modelling using advanced statistical physical models was performed to describe how acetaminophen and caffeine molecules are adsorbed in the active sites of TB-KOH. Through the characterizations, it was observed that the activation with KOH contributed to the development of porosity and functional groups (-OH, C-O, and C = O) on the surface of TB. The monocomponent adsorption equilibrium was reached in 90 min with a maximum adsorption capacity of 424.7 and 350.8 mg g-1 for acetaminophen and caffeine, respectively. For the bicomponent solution adsorption, the maximum adsorption capacity was 199.4 and 297.5 mg g-1 for acetaminophen and caffeine, respectively. The isotherm data was best fitted to the Sips model, and the thermodynamic study indicated that acetaminophen removal was endothermic, while caffeine removal was exothermic. The mechanism of adsorption of acetaminophen and caffeine by TB-KOH was described by the involvement of hydrogen bonds and π-π interactions between the surface of TB-KOH and the molecules of the contaminants.

Valorization and Upcycling of Acid Mine Drainage and Plastic Waste via the Preparation of Magnetic Sorbents for Adsorption of Emerging Contaminants

Plastic waste poses a serious environmental risk, but it can be recycled to produce a variety of nanomaterials for water treatment. In this study, poly(ethylene terephthalate) (PET) waste and acid mine drainage were used in the preparation of magnetic mesoporous carbon (MMC) nanocomposites for the adsorptive removal of pharmaceuticals and personal care products (PPCPs) from water samples. The latter were then characterized using Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD), scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDX), transmission electron microscopy (TEM), Brunauer-Emmett-Teller (BET), and ζ potential. The results of Brunauer-Emmett-Teller isotherms revealed high specific surface areas of 404, 664, and 936 m2/g with corresponding pore sizes 2.51, 2.28, and 2.26 nm for MMC, MMAC-25%, and MMAC-50% adsorbents, respectively. Under optimized conditions, the equilibrium studies were best described by the Langmuir and Freundlich models and kinetics by the pseudo-second-order model. The maximum adsorption capacity for monolayer adsorption from the Langmuir model was 112, 102, and 106 mg/g for acetaminophen, caffeine, and carbamazepine, respectively. The composites could be reused for up to six cycles without losing their adsorption efficiency. Furthermore, prepared adsorbents were used to remove acetaminophen, caffeine, and carbamazepine from wastewater samples, and up to a 95% removal efficiency was attained.

Removal of tetracycline from the aquatic environment using activated carbon: A comparative study of adsorption performance based on the activator agents

This research focus endeavour to compare the remediation of tetracycline (TC) through activated carbon (AC), crafted utilizing two distinct chemical activators: zinc chloride (ACZ), and potassium hydroxide (ACK), using pine cone biowaste as an effective carbon precursor, followed by microwave-assisted activation. The impact of TC removal by ACZ and ACK adsorbents was thoroughly examined. The influence of pH, adsorbent mass, adsorption isotherms, kinetics, and inclusive thermodynamics were studied. Our results revealed that the interaction between TC and ACZ or ACK adsorbents aligned well with the model of pseudo-second-order kinetics, whilst the Langmuir model fitted the adsorption isotherm data of ACZ and ACK. The ACZ have a maximum adsorption capacity of 327.87 mg/g compared to that of the ACK (283.29 mg/g). Adsorption of TC was facilitated by the suitable pore volume, abundant microporous, and mesoporous structure of these adsorbents. The ACZ adsorbent is abundant in oxygen-containing functional groups, compared to ACK with minimized reactive sites, in bonding with the TC molecules through hydrogen bonding, for faster removal of TC. Our finding from this work further highlights that the synthesized ACZ from pine cones evidenced significant environmental potentials in the elimination of antibiotics from aqueous solution, to promote clean application perspectives.

Boosting acetaminophen degradation in water by peracetic acid activation: A novel approach using chestnut shell-derived biochar at varied pyrolysis temperatures

In this study, biochar derived from chestnut shells was synthesized through pyrolysis at varying temperatures from 300 °C to 900 °C. The study unveiled that the pyrolysis temperature is pivotal in defining the physical and chemical attributes of biochar, notably its adsorption capabilities and its role in activating peracetic acid (PAA) for the efficient removal of acetaminophen (APAP) from aquatic environments. Notably, the biochar processed at 900 °C, referred to as CN900, demonstrated an exceptional adsorption efficiency of 55.8 mg g-1, significantly outperforming its counterparts produced at lower temperatures (CN300, CN500, and CN700). This enhanced performance of CN900 is attributed to its increased surface area, improved micro-porosity, and a greater abundance of oxygen-containing functional groups, which are a consequence of the elevated pyrolysis temperature. These oxygen-rich functional groups, such as carbonyls, play a crucial role in facilitating the decomposition of the O-O bond in PAA, leading to the generation of reactive oxygen species (ROS) through electron transfer mechanisms. This investigation contributes to the development of sustainable and cost-effective materials for water purification, underscoring the potential of chestnut shell-derived biochar as an efficient adsorbent and catalyst for PAA activation, thereby offering a viable solution for environmental cleanup efforts.

Valorization of residual lignocellulosic biomass in South America: a review

Residual lignocellulosic biomass (RLB) is a valuable resource that can help address environmental issues by serving as an alternative to fossil fuels and as a raw material for producing various value-added molecules. To gain a comprehensive understanding of the use of lignocellulosic waste in South America, a review was conducted over the last 4 years. The review focused on energy generation, biofuel production, obtaining platform molecules (such as ethanol, hydroxymethylfurfural, furfural, and levulinic acid), and other materials of interest. The review found that Brazil, Colombia, and Ecuador had the most RLB sources, with sugarcane, oil palm, and rice crop residues being the most prominent. In South America, RLB is used to produce biogas, syngas, hydrogen, bio-oil, biodiesel, torrefied biomass, pellets, and biomass briquettes. The most studied and produced value-added molecule was ethanol, followed by furfural, hydroxymethylfurfural, and levulinic acid. Other applications of interest that have been developed with RLB include obtaining activated carbon and nanomaterials. Significant progress has been made in South America in utilizing RLB, and some countries have been more proactive in regulating its use. However, there is still much to learn about the potential of RLB in each country. This review provides an updated perspective on the typification and valorization of residual biomass in South America and discusses the level of research and technology being applied in the region. This information can be helpful for future research on RLB in South America.

Determination of sulfonamide antibiotics by magnetic porous carbon solid-phase extraction coupled with capillary electrophoresis

Sulfonamide antibiotics (SAs) have been widely used as antibacterial drugs for the prevention and treatment of livestock and poultry diseases, but they seriously threaten human health because they can accumulate in humans. Therefore, it is highly important to develop methods for monitoring sulfonamide residues in aquaculture and food. In this research, based on the generation of porous carbon (PC) by the pyrolysis of sodium citrate, magnetic porous carbon (PC@Fe3O4) was synthesized by a solvothermal method and used as an adsorbent for the magnetic solid-phase extraction of SAs. The effects of the proportion of PC in PC@Fe3O4, adsorbent dosage, adsorption time, eluent type, extraction pH, salt concentration and eluent dosage on the extraction efficiency were systematically studied. The adsorption performance and behavior of PC@Fe3O4 on SAs were evaluated using adsorption kinetics and adsorption isotherms, and the adsorption mechanism was preliminarily discussed. Under optimal conditions, combined with capillary electrophoresis diode array detection, a sensitive detection method for SAs was developed. The proposed method can be used for the determination of six SAs in fishpond water and milk samples, with a linear range of 0.5-200 ng mL-1, detection limits of 0.24-0.34 ng mL-1, and spiked recoveries of 85.9-109.0 %.

Diatomite supported highly-dispersed ZnO/Zn-co-embedded ZIF-8 derived porous carbon composites for adsorption desulfurization

The metal organic framework (MOFs)-derived porous carbon materials with highly dispersed metal active sites were of the exclusive application foreground in many field, such as catalyst, electrochemistry, adsorption desulfurization and so on. However, the loss issue of metal active sites in MOFs frame was indispensable during the high temperature carbonization because of the lower boiling point of many metals, thus fundamentally affecting the atom-scale uniform distribution merit of MOFs-derived porous carbon materials. This work was to provide a novel strategy to address the loss issue of the active metal volatilization in the fabrication of MOFs-derived porous carbon materials. The ZnO nanosheets were pre-grown on the surface of diatomite by using in-situ microwave-assisted preparation, and thereafter the Zn-containing ZIF-8 particles covered the surface of ZnO nanosheets by virtue of the ZnO-induced growth. The results affirmed that the high content Zn-doped porous carbon materials were achieved and the Zn volatilization in MOFs was restrained on account of the occurrence of ZnO on diatomite (DE) surface during the carbonization. The adsorption desulfurization performance of the ZnO/Zn-embedded porous carbon materials/DE (ZnO/Zn/C@DE) was examined by the sulfur-containing compounds in simulated oil. The adsorption desulfurization performance investigation indicated that the ZnO/Zn/C@DE had the optimum adsorption capacities of 45.3 mg/g for benzothiophene and 37.4 mg/g for thiophene. Nonetheless, the competitive adsorption desulfurization finding of toluene in simulated oil showed that the adsorption capacities of ZnO/Zn/C@DE for TH and BT were dramatically descended, suggesting the presence of S-M interaction, wherein S stood for the S atom in a thiophene molecule and their analogs, and M for Zn atoms in porous carbon materials.

Blighia sapida Waste Biochar in Batch and Fixed-Bed Adsorption of Chloroquine Phosphate: Efficacy Validation Using Artificial Neural Networks

The present study investigated the potency of biochar prepared from Blighia sapida seedpods (BSSPs) in the uptake of chloroquine phosphate (CQP) from single-component batch and multicomponent fixed-bed adsorption systems. BSSPs presented a highly porous structure with a BET surface area of 1122.05 m2/g, to which adsorption efficiency correlated. The Dubinin-Radushkevich isotherm energy was obtained as 129.09 kJ/mol, confirming the chemisorption nature of the BSSP-CQP adsorption system. The efficiency of the artificial neural network (ANN) was evaluated using the lowest mean square error (MSE = 7.27) and highest correlation coefficient (R2 = 0.9910). A good agreement between the experimental results and the ANN-predicted data indicated the efficiency of the model. The percentage removal of 95.78% obtained for the column adsorption studies indicated the effectiveness of BSSPs in a multicomponent system. The mechanism of the interaction proceeded via hydrogen bonding and electrostatic attraction. This was confirmed by the high desorption efficiency (69.11%) with a HCl eluent. The degree of reversibility was found to be 2.95, indicating the reusability potential of BSSPs. BSSPs are therefore considered multilayered adsorbents with potential applications in pharmaceutical wastewater treatment.

Fabrication of the flower-like Z-scheme heterojunction photocatalyst Bi-BiOI/UiO 66 for enhanced photodegradation of acetaminophen in simulated wastewater

Acetaminophen is a representative contaminant of emerging persistent organic pollutants that can cause environmental problems when it enters municipal wastewater. An innovative flower-like Z-scheme photocatalyst Bi-BiOI/UiO 66 heterojunction composite was designed and constructed via a one-step solvothermal method. Investigations demonstrated that the Z-scheme structure strongly contributes to increasing the degradation efficiency of micropollutants. The results indicate that the bandgap energy (Eg) of the Bi-BiOI/UiO 66 composite decreases significantly from 3.22 eV to 2.43 eV, in comparison with that of pure copper-based UiO 66. Under suitable conditions (5 mg/L Ace, pH 3, 0.05 g/L), the organic pollutants in the water can be removed completely. A k value of 5.67 × 10-2 min-1 for the Bi-BiOI/UiO 66 heterojunction composite was found to effectively represent the acetaminophen photodegradation process. The reaction mechanism of acetamide in aqueous solution is also discussed. The Bi in Bi-BiOI can use surface plasmon resonance to form an electric field and accelerate the separation of photogenerated electrons and holes. This study highlights the potential of a novel photocatalyst for practical application.

Sustainable synthesis of magnetic Sargassum siliquastrum activated carbon loaded with NiS nanorods for adsorption of 2,4-D herbicide

The upgrade of sustainable resource waste into a valuable and beneficial material is an urgent task. The current paper outlines the development of an economical, sustainable, and prolonged adsorbent derived from Sargassum siliquastrum biomass and its use for potent 2,4-dichlorophenoxyacetic acid (2,4-D) removal. A simple carbonization approach was applied to obtain the highly functionalized carbon structure, which was subsequently transformed into a novel magnetic nanoadsorbent. The magnetic nanoadsorbent was characterized using Fourier transform infrared spectrometer (FTIR), X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDX), Brunauer Emmett Teller (BET)-specific surface area, and vibrating sample magnetometer (VSM). The characterization results confirm the successful formation of a high specific surface area and a uniform distribution of Fe3O4/NiS NPs grafted activated carbon. The adsorption kinetics was more accurately described via the pseudo-second order model; nevertheless, the isothermal data showed that the Langmuir model was most suitable. The monolayer adsorption capacity for 2,4-D was 208.26 ± 15.75 mg/g at 328 K. The favourability and spontaneity of the adsorption process were demonstrated by thermodynamic studies. The adsorbent displayed exceptional selectivity for 2,4-D and high stability in multi-cycle use. Electrostatic attraction, π-π stacking, and hydrogen bonding were all believed to have an impact on the sorbent's robust 2,4-D adsorption. Analyses of real tap and Nile River water samples showed little effect of the sample matrix on 2,4-D adsorption. This study presents an innovative approach for developing highly efficient adsorbent from natural biomass and offers an affordable way to recycle algal waste into beneficial materials.

PVA/PAA/DMTD electrospun nanofibrous membrane for the selective adsorption of Pb(II) ions in liquid foods

Lead (Pb(II)) contamination is common in liquid foods and can result from Pb(II) being present in the raw materials or during handling processes. However, due to the complexity of food matrices, there is limited data available concerning Pb(II) ion removal from food sources. This study focused on fabricating a PVA/PAA/DMTD electrospun nanofibrous membrane (ENFM) to efficiently and selectively remove Pb(II) ions from liquid foods. The PVA/PAA/DMTD ENFM had a maximum adsorption capacity of 138.3 mg/g for Pb(II) ions and demonstrated high selectivity toward the removal of Pb(II) ions. Negative values of the Gibbs free energy (ΔG°) showed that the spontaneous nature of the adsorption process was feasible at different temperatures. Moreover, it successfully removed Pb(II) ions from selected samples of commercially available drinks. Therefore, this adsorbent exhibits significant potential for removing Pb(II) ions from liquid food products, thereby reducing daily dietary exposure to Pb(II).

Iron/nitrogen co-doped biochar derived from salvaged cyanobacterial for efficient peroxymonosulfate activation and ofloxacin degradation: Synergistic effect of Fe/N in non-radical path

A green, low-cost, high-performance Fe/N co-doped biochar material (Fe-N@C) was synthesized using salvaged cyanobacteria without other extra precursors for peroxymonosulfate (PMS) activation and ofloxacin (OFX) degradation. With the increased pyrolysis temperature, the graphitization degree, the specific surface area and the corresponding groups like OH, COO etc. for Fe-N@C tended to increase, resulting in a greater OFX adsorption. However, the total amount of Fe-NX and graphitic nitrogen groups in the Fe-N@C composites was firstly increased and then decreased, which reached the highest at 800 °C (Fe-N@C-800). All these changes of functional species ascribed to the strong interaction between Fe, N and C led to the highest defect degree of Fe-N@C-800, resulting the highest OFX removal efficiency of 95.0 %. OFX removal experiments indicated the adsorption process promoted the total OFX degradation for different functional groups on Fe-N@C composites separately dominated the process of OFX adsorption and PMS catalysis. Radical quenching and electron paramagnetic resonance (EPR) measurements proved free radical and non-free radical pathways participated in Fe-N@C/PMS system. The non-free radicals based on 1O2 and high-valent iron-oxo species played a more important role in OFX degradation, leading to the minimal effect of co-existing anions and the high universality for other antibiotic pollutants. Fe-NX was utilized as the main catalytic sites and graphitic nitrogen contributed more to the electron transfer for PMS activation, whose synergistic effect efficiently facilitated OFX degradation. Finally, the possible degradation route of OFX in the Fe-N@C-800/PMS system was proposed. All these results will provide the new insights into the intrinsic mechanism of Fe/N species in carbon-based materials for PMS activation.

Cu+-Doped PVA-Derived Mesoporous Carbon@Diatomite Adsorbent for Selective Adsorption Desulfurization

Herein, we successfully constructed a Cu+-doped PVA-derived mesoporous carbon@diatomite (DE) composite by virtue of N2-suffered carbonization and self-reduction at a high temperature. The structure and composition of C/Cu@DE composite adsorbents were determined by a series of characterizations. The results affirmed that Cu+ species are highly scattered in PVA-derived mesoporous carbon, which covered the DE surface. The effect of carbonization temperature on the structure and composition of the C/Cu@DE composite adsorbents were intensively investigated, indicating that the C/Cu@DE composite at an 800 °C carbonization temperature (C/Cu@DE-800 °C) showed the formation of many Cu+ species and preferable hierarchical pore properties. The adsorption experiments of benzothiophene (BT) indicated that C/Cu@DE-800 °C possessed a better adsorption capacity. The adsorption behavior of BT onto C/Cu@DE-800 °C was investigated by a variety of adsorption times, initial concentrations, and recycle times, of which the largest adsorption capacity for BT attained 34.2 mg/g. Furthermore, the adsorption kinetics, intraparticle diffusion, adsorption isotherms, and adsorption thermodynamics of BT onto C/Cu@DE-800 °C was deeply studied, which contributed to the proposed adsorption mechanism.

The efficient removal of ibuprofen, caffeine, and bisphenol A using engineered egusi seed shells biochar: adsorption kinetics, equilibrium, thermodynamics, and mechanism

Contaminants of emerging concern (CECs), also known as micropollutants, have been recognized in recent years as substantial water pollutants because of the potential threats they pose to the environment and human health. This study was aimed at preparing biochar (BC) based on egusi seed shells (ESS) with well-developed porosity and excellent adsorption capacity towards CECs including ibuprofen (IBP), caffeine (CAF), and bisphenol A (BPA). BC samples were prepared by pyrolysis at different temperatures (400 to 800 °C) and were characterized using nitrogen sorption, FTIR, powder X-ray diffraction (PXRD), SEM/EDS, elemental analysis, and thermal analysis. The nitrogen sorption and SEM results showed that the textural properties were more prominent as the pyrolysis temperature increased. The BC sample obtained at 800 °C which exhibited the largest specific surface area (688 m2/g) and the highest pore volume (0.320 cm3/g) was selected for the adsorption study of CECs. The kinetic study shows that the adsorption equilibrium of CAF and BPA was faster than that of IBP. The pseudo-first- and pseudo-second-order kinetic models best fitted the adsorption data. The Langmuir maximum monolayer adsorption capacities of biochar were found to be ~ 180, 121, and 73 mg/g respectively for IBP, CAF, and BPA. The thermodynamic study shows that the adsorption process was spontaneous and endothermic for the three CECs. The results of the adsorption and the analysis of BC after adsorption showed that hydrogen bonding, van der Waals, π-π, n-π interactions, and pore filling were involved in the adsorption mechanism. The prepared biochar BC from ESS displayed a large surface area and good morphology and significantly promotes adsorption of CECs and good efficiency on synthetic effluent. Finally, it offers a low-cost and cleaner production method.

Efficient removal of pharmaceutical contaminants from water and wastewater using immobilized laccase on activated carbon derived from pomegranate peels

In this study, pomegranate peels (PPs) as an abundant fruit processing waste was used to produce cost-effective, eco-friendly, and high-quality activated carbon. The produced carbon (fossil free activated carbon) was used for immobilizing laccase to remove a range of emerging pollutants namely diclofenac, amoxicillin, carbamazepine, and ciprofloxacin from water and wastewater. The loaded activated carbon by laccase (LMPPs) and the unloaded one (MPPs) were characterized using advanced surface chemistry analysis techniques. MPPs was found to have a porous structure with a large surface area and an abundance of acidic functional groups. Laccase immobilization reduced surface area but added active degradation sites. The optimal immobilization parameters were determined as pH 4, 35 °C, and a laccase concentration of 2.5 mg/mL resulting in a 69.8% immobilization yield. The adsorption of the emerging pollutant onto MPPs is best characterized as a spontaneous endothermic process that adheres to the Langmuir isotherm and first-order kinetics. Using synergistic adsorption and enzymatic degradation, the target pollutants (50 mg/L) were eliminated in 2 h. In both water types, LMPPs outperformed MPPs. This study shows that pomegranate peels can effectively be harnessed as an enzyme carrier and adsorbent for the removal of emerging pollutants even from a complex sample matrix. The removal of contaminants from wastewater lasted five cycles, whereas it continued up to six cycles for water.

Synthesis, Characterization, and Adsorption Properties of Nitrogen-Doped Nanoporous Biochar: Efficient Removal of Reactive Orange 16 Dye and Colorful Effluents

In this work, nitrogen-doped porous biochars were synthesized from spruce bark waste using a facile single-step synthesis process, with H₃PO₄ as the chemical activator. The effect of nitrogen doping on the carbon material's physicochemical properties and adsorption ability to adsorb the Reactive Orange 16 dye and treat synthetic effluents containing dyes were evaluated. N doping did not cause an important impact on the specific surface area values, but it did cause an increase in the microporosity (from 19% to 54% of micropores). The effect of the pH showed that the RO-16 reached its highest removal level in acidic conditions. The kinetic and equilibrium data were best fitted by the Elovich and Redlich-Peterson models, respectively. The adsorption capacities of the non-doped and doped carbon materials were 100.6 and 173.9 mg g^-1, respectively. Since the biochars are highly porous, pore filling was the main adsorption mechanism, but other mechanisms such as electrostatic, hydrogen bond, Lewis acid-base, and π-π between mechanisms were also involved in the removal of RO-16 using SB-N-Biochar. The adsorbent biochar materials were used to treat synthetic wastewater containing dyes and other compounds and removal efficiencies of up to 66% were obtained. The regeneration tests have demonstrated that the nitrogen-doped biochar could be recycled and reused easily, maintaining very good adsorption performance even after five cycles. This work has demonstrated that N-doped biochar is easy to prepare and can be employed as an efficient adsorbent for dye removal, helping to open up new solutions for developing sustainable and effective adsorption processes to tackle water contamination.

Efficient Removal of Analgesic and Anti-Inflammatory Drugs from Sewage Treatment Plant Effluents Using Magnetite Nanoparticles Synthesized Red Mud

Due to the COVID-19 epidemic, the consumption of pharmaceuticals, especially paracetamol, has sharply increased on a global scale. The increasing concentration of analgesic and anti-inflammatory drugs (AAIDs) in the aquatic medium is a global problem for human and aquatic life. Therefore, simple and effective treatment options for removing AAIDs from wastewater after the COVID-19 pandemic are needed. The removal of AAIDs (acetaminophen, acetylsalicylic acid, codeine, diclofenac, ibuprofen, indomethacin, ketoprofen, mefenamic acid, naproxen, and phenylbutazone) from sewage treatment plant (STP) effluents by the prepared magnetite nanoparticles synthesized from red mud (mNPs-RM) is presented for the first time in this study. The removal efficiencies of AAIDs onto mNPs-RM were determined to be between 90% (diclofenac) and 100% (naproxen, codeine, and indomethacin). Acetaminophen (paracetamol) was used as a model compound in kinetic and isotherm model studies. The adsorption of acetaminophen was matched well with the pseudo second order kinetic model. Film diffusion governed its rate mechanism. The Freundlich isotherm model preferably fitted the adsorption data with an adsorption capacity of 370 mg/g at 120 min contact time at pH 7.0 at 25 °C. Furthermore, the regenerated mNPs-RM were used four times without affecting the adsorption capacity and the magnetic separability. mNPs-RM can be used as a simple, inexpensive and effective adsorbent for removing AAIDs from STP effluents. Also, low cost adsorbent obtained from industrial waste could be employed to replace the high cost activated carbons for the adsorption of other micro pollutants in STP effluents.

Supplementary Information

The online version contains supplementary material available at 10.1007/s11270-023-06404-7.

Effective removal of selected pharmaceuticals from sewerage treatment plant effluent using natural clay (Na-montmorillonite)

The consumption of pharmaceuticals has rapidly increased on a global scale due to the serious increase in Covid-19, influenza and respiratuar sinsityal virus, which is called "triple epidemic" in the world. The use of non-prescription analgesic and anti-inflammatory drugs (AAIDs), especially paracetamol, is higher compared to pre-pandemic. This increased the AAIDs load discharged to the aqueous media through sewerage treatment plant (STP). Therefore, simple and effective treatment options for removing AAIDs from STP effluents are needed. The aim of the study was to remove AAIDs (paracetamol, acetylsalicylic acid, codeine, diclofenac, ibuprofen, indomethacin, ketoprofen, mefenamic acid, naproxen, and phenylbutazone) from STP effluents by nearly pure natural clay Na-montmorillonite. The Na-montmorillonite taken from the Ordu region in the northern part of Turkey. Surface area of the Na-montmorillonite is 99.58 m2/g and CEC is 92.40 meq/100 g. The removal efficiencies of AAIDs using Na-montmorillonite were between 82 ± 5% (ibuprofen) and 94 ± 4% (naproxen). Paracetamol was used as a model compound in kinetic and isotherm model studies. Freundlich isotherm model and the pseudo second order kinetic model were the best-fit using the obtained experimental data. Film diffusion governed its rate mechanism. The paracetamol adsorption capacity was acquired as 244 mg/g at 120 min contact time at pH 6.5 at 25 °C. With this study, it could be shown that montmorillonite can be used effectively to eliminate paracetamol from STP effluent. Natural clay can be used as a simple, inexpensive and effective adsorbent for removing AAIDs from STP effluents.

Supplementary Information

The online version contains supplementary material available at 10.1007/s13201-023-01930-5.

Sensitive determination of bisphenols in environmental samples by magnetic porous carbon solid-phase extraction combined with capillary electrophoresis

Bisphenol compounds exist widely in the environment and pose potential hazards to the environment and human health, which has aroused widespread concern. Therefore, there is an urgent need for an efficient and sensitive analytical method to enrich and determine trace bisphenols in environmental samples. In this work, magnetic porous carbon (MPC) was synthesized by one-step pyrolysis combined with a solvothermal method for magnetic solid-phase extraction of bisphenols. The structural properties of MPC were characterized by field emission scanning electron microscopy, transmission electron microscopy, Fourier transform infrared spectroscopy, and saturation magnetization analysis. Its adsorption properties were evaluated by adsorption kinetics and adsorption isotherm studies. By optimizing the magnetic solid-phase extraction and capillary electrophoresis separation conditions, a capillary electrophoresis separation and detection method for four bisphenols was successfully constructed. The results showed that the detection limits of the proposed method for the four bisphenols were 0.71-1.65 ng/mL, the intra-day and inter-day precisions were 2.27-4.03% and 2.93-4.42%, respectively, and the recoveries were 87.68%-108.0%. In addition, the MPC could be easily recycled and utilized, and even if the magnetic solid-phase extraction was repeated 5 times, the extraction efficiency could still be kept above 75%.

Adsorption of the First-Line Covid Treatment Analgesic onto Activated Carbon from Residual Pods of Erythrina Speciosa

In this study, the residual pods of the forest species Erythrina speciosa were carbonized with ZnCl₂ to obtain porous activated carbon and investigated for the adsorptive removal of the drug paracetamol (PCM) from water. The PCM adsorption onto activated carbon is favored at acidic solution pH. The isothermal studies confirmed that increasing the temperature from 298 to 328 K decreased the adsorption capacity from 65 mg g^-1 to 50.4 mg g^-1 (C₀ = 175 mg L^-1). The Freundlich model showed a better fit of the equilibrium isotherms. Thermodynamic studies confirmed the exothermic nature (ΔH⁰ = -39.1066 kJ mol^-1). Kinetic data indicates that the external mass transfer occurs in the first minutes followed by the surface diffusion, considering that the linear driving force model described the experimental data. The application of the material in the treatment of a simulated effluent with natural conditions was promising, presenting a removal of 76.45%. Therefore, it can be concluded that the application of residual pods of the forest species Erythrina speciosa carbonized with ZnCl₂ is highly efficient in the removal of the drug paracetamol and also in mixtures containing other pharmaceutical substances.

Multifunctional Cross-Linked Shrimp Waste-Derived Chitosan/MgAl-LDH Composite for Removal of As(V) from Wastewater and Antibacterial Activity

This work synthesized a novel chitosan-loaded MgAl-LDH (LDH = layered double hyroxide) nanocomposite, which was physicochemically characterized, and its performance in As(V) removal and antimicrobial activity was evaluated. Chitosan-loaded MgAl-LDH nanocomposite (CsC@MgAl-LDH) was prepared using cross-linked natural chitosan from shrimp waste and modified by Mg-Al. The main mechanisms predominating the separation of As(V) were elucidated. The characteristic changes confirming MgAl-LDH modification with chitosan were analyzed through Fourier transform infrared spectroscopy, X-ray diffraction, thermogravimetric analysis-differential thermal analysis, and Brunauer-Emmett-Teller measurements. Porosity and the increased surface area play an important role in arsenic adsorption and microbial activity. Adsorption kinetics follows the general order statistically confirmed by Bayesian Information Criterion differences. To understand the adsorption process, Langmuir, Freundlich, and Liu isotherms were studied at three different temperatures. It was found that Liu's isotherm model was the best-fitted model. CsC@MgAl-LDH showed the maximum adsorption capacity of 69.29 mg g^-1 toward arsenic at 60 °C. It was observed that the adsorption capacity of the material rose with the increase in temperature. The spontaneous behavior and endothermic nature of adsorption was confirmed by the thermodynamic parameters study. Minimal change in percentage removal was observed with coexisting ions. The regeneration of material and adsorption-desorption cycles revealed that the adsorbent is economically efficient. The nanocomposite was very effective against Staphylococcus aureus and Bacillus subtilus.

Nitrogen Doped Porous Biochar/β-CD-MOFs Heterostructures: Bi-Functional Material for Highly Sensitive Electrochemical Detection and Removal of Acetaminophen

Acetaminophen (AC) is one of the most common over-the-counter drugs, and its pollutant in groundwater has attracted more attention due to its serious risk to human health. Currently, the research on AC is mainly focused on its detection, but few are concerned about its removal. In this work, for the first time, nitrogen-doped Soulangeana sepals derived biochar/β-cyclodextrin-Metal-organic frameworks (N-SC/β-CD-MOFs) composite was proposed for the simultaneous efficient removal and detection of AC. N-SC/β-CD-MOFs combined the properties of host-guest recognition of β-CD-MOFs and porous structure, high porosity, and large surface area of N-SC. Their synergies endowed N-SC/β-CD-MOFs with a high adsorption capacity toward AC, which was up to 66.43 mg/g. The adsorption type of AC on the surface of N-SC/β-CD-MOFs conformed to the Langmuir adsorption model, and the study of the adsorption mechanism showed that AC adsorption on N-SC was mainly achieved through hydrogen bonding. In addition, the high conductivity, large specific surface area and abundant active sites of N-SC/β-CD-MOFs were of great significance to the high-performance detection of AC. Accordingly, the sensor prepared with N-SC/β-CD-MOFs presented a wide linear range (1.0-30.0 μM) and a low limit of detection of 0.3 nM (S/N = 3). These excellent performances demonstrate that N-SC/β-CD-MOFs could act as an efficient dual-functional material for the detection and removal of AC.

Sonicating for the Uptake of Paracetamol from Solution by Activated Carbon from Oak: Kinetics, Thermodynamics, and Isotherms

This inquiry used ultrasonic waves to uptake paracetamol (PA) by using oak-based activated carbon (ACO). The surface of ACO was explored based on FT-IR, SEM, and XRD before and after the adsorption. The kinetic data for PA adsorption onto ACO corresponds to a pseudo-second-order kinetic model. Isothermal models of the Langmuir, Freundlich, D-R, and Temkin were used. The adsorption of PA onto ACO was found to be a monolayer with 96.03% uptake, which corresponds to Langmuir. The thermodynamic experiments revealed the endothermic nature of PA adsorption onto ACO. Under the investigated optimal conditions, the adsorption capacity of PA onto ACO was found to be 97.1 mg. L-1. ACO could be recycled after six regenerations. Ultimately, sonicating has adequate performance for the uptake of PA by ACO.

Paracetamol and amoxicillin adsorptive removal from aqueous solution using phosphoric acid activated-carbon

Charcoal-based materials have attracted much attention for the removal of pharmaceutical agents. The charcoal-based carbon materials have green synthetic routes, high surface area, numerous active site with active functional groups available for physico-chemical interactions with adsorbate for surface-adsorptive removal of toxins. In this study, acid treated activated carbon was developed from the peach seeds using thermal pyrolysis approach. Phosphoric acid activated carbon (PAC) was further modified by HNO3 and employed as an adsorbent for the removal of amoxicillin and paracetamol and process variables were optimized for enhanced removal of amoxicillin and paracetamol. The adsorption of pharmaceutical agents was significantly affected by temperature, pH and reaction time. The amoxicillin and paracetamol sorption process onto PCA followed a pseudo second order kinetics and Langmuir isotherm model with a maximum removal capacity of 51.8 mg/g and 51.1 mg/g, respectively. The results revealed that acid activated carbon has promising efficiency for the removal of amoxicillin and paracetamol from aqueous medium and peach seeds derived PCA could be employed for the removal of these pharmaceutical agents from effluents and PAC is also extendable for the removal of other drugs from pharmaceutical wastewater streams.

Chemically activated carbon preparation from natural rubber biosludge for the study of characterization, kinetics and isotherms, thermodynamics, reusability during Cr(VI) and methylene blue adsorption

Alkaline leachate, dust generation, and foul smell during the stacking process of natural rubber biosludge (NRBS) can pollute surrounding water, soil, and air. In this study, natural rubber chemically activated carbon (NRCAC) has been synthesized for the first time from NRBS by pyrolysis using ZnCl₂ at 700 °C for adsorptive removal of Cr(VI) and methylene blue (MB) from aqueous solutions. Both NRBS and NRCAC were characterized by X-ray fluorescence (XRF), X-ray diffraction (XRD), Fourier transform infrared (FTIR), scanning electron microscopy-energy dispersive spectroscopy (SEM-EDS), Brunauer-Emmett-Teller (BET), and thermogravimetric analyzer (TGA). FTIR and SEM-EDS suggested significant functional and morphological transformations in NRCAC. Experimental investigations of different process parameters, such as pH, concentration, contact time, salt concentration, etc., were conducted to study their influences on adsorption. Adsorption and desorption kinetics followed a pseudo-second-order model, while adsorption equilibrium followed Liu isotherm. Maximum uptake calculated from the Liu model was 81.28 and 211.90 mg/g for Cr(VI) and MB, respectively. Thermodynamic analysis established spontaneous and endothermic adsorption. Up to five adsorption/desorption cycles were conducted using eluents such as 1 M NaOH and water for Cr(VI) and MB, respectively. Electrostatic attraction and ion-exchange favored Cr(VI)/MB adsorption, while hydrogen bonding and π-π stacking were significant in MB uptake. Overall findings suggest that NRBS (a renewable agro-industrial, abundant, and freely available) could be employed to synthesize biochar for adsorptive removal of wastewater containing Cr(VI)/MB.

Two-stage preparation of highly mesoporous carbon for super-adsorption of paracetamol and tetracycline in water: Important contribution of pore filling and π-π interaction

This study aimed to develop an extremely highly porous activated carbon derived from soybean curd residues (SCB-AC) through two-step pyrolyzing coupled with KOH activating process and then apply it for removing paracetamol (PRC) and tetracycline (TCH) from water. The optimal conditions for chemical activation were 800 °C and the ratio of KOH to material (4/1; wt./wt.). SCB-AC adsorbents (before and after adsorption) were characterized by Brunauer-Emmet-Teller (BET) analyser, Fourier-transform infrared spectroscopy (FTIR), scanning electron microscopy, and Raman spectroscopy. Adsorption kinetics, isotherm, and thermodynamics were concluded under batch experiments. The effects of pH (2-10) and NaCl (0-1 M) on adsorption processes were investigated. Reusable properties of laden SCB-AC were evaluated by studying desorption and cycles of adsorption/desorption. Results indicated that SCB-AC exhibited a large specific surface area (3306 m²/g) and high total pore volume (2.307 cm³/g), with mesoporous volume accounting for 86.9%. Its porosity characteristics (average pore width: 2.725 nm) are very appropriate for adsorbing two pharmaceuticals through pore-filling mechanism. Adsorption processes were less affected by the parameters: pH, NaCl, and water matrixes. The kinetics for adsorbing PRC reached a faster equilibrium than that for TCH. The Langmuir maximum adsorption capacity of SCB-AC (pH_eq 7.0 and 25 °C) was 1235 mg/g (for adsorbing TCH) and 646 mg/g (PRC). Pore filling (confirmed by BET analyser) and π-π interaction (confirmed by FTIR and Raman spectroscopy) were dominant adsorption mechanisms. Those mechanisms were physisorption (ΔH° = 13.71 and -21.04 kJ/mol for adsorbing TCH and PRC, respectively). SCB-AC can serve as an outstanding material for removing pharmaceuticals from water.

Composite of methyl polysiloxane and avocado biochar as adsorbent for removal of ciprofloxacin from waters

Two carbon composite materials were prepared by mixing avocado biochar and methyl polysiloxane (MK). Firstly, MK was dissolved in ethanol, and then the biochar was added at different times. In sample 1 (R1), the time of adding biochar was immediately after dissolving MK in ethanol, and in sample 2 (R₂), after 48 h of MK dissolved in ethanol. The samples were characterized by nitrogen adsorption/desorption measurements obtaining specific surface areas (S_BET) of 115 m2 g^-1 (R₁) and 580 m2 g^-1 (R₂). The adsorbents were further characterized using scanning electron microscopy, FTIR and Raman spectroscopy, adsorption of vapors of n-heptane and water, thermal analysis, Bohem titration, pHpzc, and C H N elemental analysis. R₁ and R₂ adsorbents were employed as adsorbents to remove the antibiotic ciprofloxacin from the waters. The t_1/2 and t_0.95 based on the interpolation of Avrami fractional-order were 20.52 and 246.4 min (R₁) and 14.00 and 157.6 min (R₂), respectively. Maximum adsorption capacities (Q_max) based on the Liu isotherm were 10.77 (R₁) and 63.80 mg g^-1 (R₂) for ciprofloxacin. The thermodynamic studies showed a spontaneous and exothermic process for both samples, and the value of ΔH° is compatible with physical adsorption.

Preparation and Characterization of Pulp and Paper Mill Sludge-Activated Biochars Using Alkaline Activation: A Box-Behnken Design Approach

This study utilized pulp and paper mill sludge as a carbon source to produce activated biochar adsorbents. The response surface methodology (RSM) application for predicting and optimizing the activated biochar preparation conditions was investigated. Biochars were prepared based on a Box-Behnken design (BBD) approach with three independent factors (i.e., pyrolysis temperature, holding time, and KOH:biomass ratio), and the responses evaluated were specific surface area (SSA), micropore area (S _micro), and mesopore area (S _meso). According to the RSM and BBD analysis, a pyrolysis temperature of 800 °C for 3 h of holding and an impregnation ratio of 1:1 (biomass:KOH) are the optimum conditions for obtaining the highest SSA (885 m² g^-1). Maximized S _micro was reached at 800 °C, 1 h and the ratio of 1:1, and for maximizing S _meso (569.16 m² g^-1), 800 °C, 2 h and ratio 1:1.5 (445-473 m² g^-1) were employed. The biochars presented different micro- and mesoporosity characteristics depending on pyrolysis conditions. Elemental analysis showed that biochars exhibited high carbon and oxygen content. Raman analysis indicated that all biochars had disordered carbon structures with structural defects, which can boost their properties, e.g., by improving their adsorption performances. The hydrophobicity-hydrophilicity experiments showed very hydrophobic biochar surfaces. The biochars were used as adsorbents for diclofenac and amoxicillin. They presented very high adsorption performances, which could be explained by the pore filling, hydrophobic surface, and π-π electron-donor-acceptor interactions between aromatic rings of both adsorbent and adsorbate. The biochar with the highest surface area (and highest uptake performance) was subjected to regeneration tests, showing that it can be reused multiple times.

Synthesis of a highly recoverable 3D MnO2/rGO hybrid aerogel for efficient adsorptive separation of pharmaceutical residue

Water contamination by non-steroidal anti-inflammatory drugs, such as acetaminophen, is an emerging ecological concern. In this study, a new three-dimensional manganese dioxide-engrafted reduced graphene oxide (3D MnO₂/rGO) hybrid aerogel was developed for acetaminophen sequestration. The synthesis involved firstly the self-assembly of GO aerogel, followed by thermal reduction and in-situ MnO₂ growth by redox-reaction. The aerogel demonstrated interlinked planes with smooth surfaces deposited with MnO₂ nanospheres and pores of 138.4 - 235.3 µm width. The influences of adsorbent dosage, initial pH, acetaminophen concentration, temperature and contact time were investigated. It was determined that the adsorption of acetaminophen occurred on uniform sorption sites in the aerogel, as suggested by the best fit of data to the Langmuir isotherm, yielding a maximum adsorption capacity of 252.87 mg/g. This highest adsorption performance of the 3D MnO₂/rGO aerogel was attained at a dosage of 0.6 g/L, initial pH of 6.2 and temperature of 40°C. The process kinetics were in-line with the pseudo-first-order and pseudo-second-order kinetics at 10 and 20 - 500 mg/L concentrations, respectively. Thermodynamic assay showed the spontaneity and endothermicity features of the 3D MnO₂/rGO-acetaminophen system. The acetaminophen adsorption mechanisms were mainly hydrogen bonding and pore entrapment. Moreover, the as-synthesised aerogel was effectively regenerated using acetone and re-utilised in four adsorption-desorption cycles. Overall, the results highly recommend the implementation of the 3D MnO₂/rGO hybrid aerogel for purification of wastewater polluted by acetaminophen residue.

The comparative performance of lightweight green wall media for the removal of xenobiotic organic compounds from domestic greywater

Green walls can provide an aesthetic approach to treat domestic greywater in urban landscapes. However, the widespread adoption of green walls for greywater treatment depends on its performance to remove the emerging contaminants from greywater such as xenobiotic organic compounds (XOCs). In this study, the performance of five lightweight green wall media types (zeolite, perlite, date seeds, coffee grinds, and coco coir) was evaluated for the removal of six XOCs representing a range of hydrophilic to hydrophobic organic micropollutants in domestic greywater (acetaminophen, diethyltoluamide, bisphenol A, oxybenzone, triclosan, nonylphenol). The adsorption affinity of targeted XOCs on different green wall media types, the role of contact time on XOCs removal, and the impact of background pollutants in greywater matrix on the adsorption of XOCs were analysed. Results indicate that removal of XOCs was higher using carbonaceous waste materials (date seeds, coffee grinds, and coco coir) as compared to natural minerals (zeolite and perlite). Moreover, the adsorption of XOCs increased with the increase in pollutant hydrophobicity. All XOCs showed highest removal using coco coir with fast adsorption kinetics, achieving 90% of the removal in 30 min. The only exception was acetaminophen that showed best removal using zeolite but exhibited slow adsorption kinetics with 90% of the removal attained in 24 h. The initial adsorption kinetics (<30 min) of XOCs in greywater were adversely affected by the presence of background pollutants, indicating the need of higher residence time of greywater in green wall system for better removal of XOCs. Based on the findings of this batch study, it is recommended to design a green wall system with more than 30 min of greywater residence time using a mixture of coco coir and zeolite for effective removal of XOCs from domestic greywater.

High surface area acid-treated biochar from pomegranate husk for 2,4-dichlorophenol adsorption from aqueous solution

In the present study, zinc chloride (ZnCl2) followed by acid treating was employed for the fabrication of activated biochar from pomegranate husk (APHBC) for 2,4-dichlorophenol (2,4-DCP) adsorption from an aqueous solution. The batch adsorption experiments were carried out as a function of solution pH, APHBC dose, initial 2,4-DCP concentration, contact time, and ionic strength. The APHBC showed a well-developed pore with specific surface areas of 1576 m2/g due to explosive characteristics of ZnCl2. In addition, the XRD analysis showed that the diffraction peaks between 15 and 35° corresponded to amorphous carbon. The pore size distribution results showed that APHBC was dominantly mesoporous materials. The pHpzc value of APHBC was 6.15 ± 0.15. According to batch experiments, the optimum adsorption conditions were pH of 3.0, contact time 60 min, APHBC dose of 1.75 g/L and without ionic strengths. The absorption capacity of 2,4-DCP at the initial concentration of 150.0 mg/L promptly decreased from 259.5 ± 12.9 to 74.5 ± 3.7 mg/g as the APHBC dose increased from 0.50 to 2.00 g/L. The isotherm and kinetics study of 2,4-DCP adsorption by APHBC revealed that Liu and Avrami fractional-order well fitted with experimental data, respectively.

Woody residues of the grape production chain as an alternative precursor of high porous activated carbon with remarkable performance for naproxen uptake from water

Activated carbon prepared from grape branches was used as a remarkable adsorbent to uptake naproxen and treat a synthetic mixture from aqueous solutions. The material presented a highly porous texture, a surface area of 938 m² g^-1, and certain functional groups, which were key factors to uptake naproxen from effluents. The maximum adsorption capacity predicted by the Langmuir model for naproxen was 176 mg g^-1. The thermodynamic study revealed that the adsorption process was endothermic and spontaneous. The linear driving force (LDF) model presented a good statistical adjustment to the experimental decay data. A suitable interaction pathway of naproxen adsorption onto activated carbon was proposed. The adsorbent material was highly efficient to treat a synthetic mixture containing several drugs and salts, reaching 95.63% removal. Last, it was found that the adsorbent can be regenerated up to 7 times using an HCl solution. Overall, the results proved that the activated carbon derived from grape branches could be an effective and sustainable adsorbent to treat wastewaters containing drugs.

Magnetized Activated Carbon Synthesized from Pomegranate Husk for Persulfate Activation and Degradation of 4-Chlorophenol from Wastewater

The compound 4-chlorophenol (4-CP) is known to be a highly toxic compound having harmful effects on human health and the environment. To date, the removal of 4-CP by advanced oxidation processes (AOPs) has attracted tremendous attentions. The persulfate-based AOPs show higher oxidation, better selectivity, wider pH range, and no secondary pollution compared to the traditional Fenton-based AOPs. Carbon materials with low cost and chemical stability are useful for the activation of persulfate (PS) to produce reactive species. Herein, we magnetized activated carbon synthesized from pomegranate husk (MPHAC). By using 4-CP as a model organic pollutant, tests of the activation of PS via MPHAC for the removal of 4-CP were performed. Batch processes were carried out to study the influence of different parameters (initial solution pH, catalyst dose, PS dose, and initial 4-CP concentration) on the adsorption of 4-CP on PHAC with ferric oxide (Fe3O4-PHAC). The results show that under the obtained optimal conditions (MPHAC dose: 1250 mg/L, PS dose: 350 mg/L, solution pH 5, an initial 4-CP concentration of 100 mg/L, and a contact time of 60 min), a 4-CP removal factor of 99.5% was reached by the developed MPHAC/PS system. In addition, it was found that reusing MPHAC in five successive cycles is feasible because the catalyst in the last cycle kept exhibiting a high potential for 4-CP absorption, indicating the economically viable procedure. Therefore, this study provides a comprehensive understanding on the degradation of 4-CP by the magnetized activated carbon persulfate system.

Simultaneous adsorption for cationic and anionic dyes using chitosan/electrospun sodium alginate nanofiber composite sponges

The coexistence of anionic and cationic dyes in dye wastewater has highlighted a great necessity to develop amphoteric adsorbents for their simultaneous removal. Herein, an amphoteric composite sponge was successfully fabricated by combining chitosan with electrospun sodium alginate nanofiber using lyophilization in acetic acid/water/dioxane mixed solvents, which owned the abundant functional groups and superior microstructure of interconnected pores and nanoscale fibers, beneficial for the adsorption capacity improvement. The optimum adsorption capacities for Acid Blue-113 and Rhodamine B were 926.2 ± 25.7 mg/g and 695.4 ± 17.0 mg/g, respectively, much higher than that of the controlled sample prepared with chitosan and non-spinning sodium alginate in traditional acetic acid/water solvents. Meanwhile, the sponge provided with the superior adsorption performance under various pH environment and cyclic adsorption. Importantly, it had considerable simultaneous adsorption capacity for binary system containing anionic and cationic dyes. Overall, the chitosan/electrospun sodium alginate nanofiber composite sponge shows potential for complex wastewater treatment.