Towards supercapacitors: Cyclic voltammetry and fast Fourier transform electrochemical impedance spectroscopy based evaluation of polypyrrole electrochemically deposited on the pencil graphite electrode

EIS Study on Competitive Adsorption at the TiO2-Solution Interface

Understanding the competition and configuration of ionic adsorption on the electrode surface is crucial for electrocatalytic reactions and corrosion science. Here, we demonstrate how EIS can be employed to identify the competitive adsorption of phosphate and chloride ions on the surface of a Ti/TiO2 electrode in a complex solution system. By controlling the concentration of phosphate ions in a high-concentration chloride ion (100 mM) and different pH (5.0, 7.0, and 9.0), we clearly observe a transition in the adsorbed species from initially chloride-dominated to phosphate-dominated on the electrode surface and the transformation of the phosphate adsorption mode. This competitive transition of adsorption species is evident in the low-concentration region of the impedance-concentration curves up to approximately 5 mM P concentration. Furthermore, the impedance-concentration curves under neutral and alkaline conditions show an additional similar switching in the high P concentration region compared with acidic conditions, indicating a shift from bidentate to monodentate phosphate adsorption on the electrode surface. This study provides a method for detecting the adsorption behavior of precursors in subsequent corrosion science.

Highly sensitive electrochemical biosensor for MUC1 detection based on DNA-functionalized CdTe quantum dots as signal enhancers

In this paper, an electrochemical biosensor based on a cadmium telluride/polypyrrole (CdTe/PPy) nanocomposite was developed for the detection of MUC1 with high selectivity and sensitivity. Results indicate that the CdTe/PPy nanocomposite is modified on the surface of the glassy carbon electrode (GCE), which affords a large surface area for immobilizing cap-DNA, ensuring its high selectivity and sensitivity. Next, CdTe-linked sig-DNA (MUC1 aptamer) was introduced, allowing the MUC1 aptamer to hybridize with cap-DNA. CdTe is a signal amplification element used to generate a differential pulse voltammetry (DPV) signal. Conceivably, target MUC1 detection was based on current signal change due to concentration change in the signal amplification element CdTe. In the presence of MUC1, the MUC1 aptamer specifically binds to MUC1, resulting in the release of CdTe-sig-DNA from the electrode surface and a decrease in peak current. Under optimized experimental conditions, the electrochemical biosensor is highly selective, sensitive, stable, and reproducible for MUC1 ranging from 0.1 nM to 100 nM with a detection limit of 0.05 nM (S/N = 3). Therefore, the electrochemical biosensor has potential applications in medical disease diagnosis.

A comprehensive review of PETW recycling for supercapacitor applications

The rising measure of waste produced from polyethene terephthalate (PET) and the interest in eco-accommodating energy storage arrangements have prompted escalated examination into reusing waste PET into supercapacitors. This review aims to provide a comprehensive overview of the most recent advancements in the recycling of polyethylene terephthalate waste (PETW), as a supercapacitor electrode precursor. The review looks at different methodologies for recovering PET from waste, including mechanical, chemical, enzyme, etc. It further explores the combination strategies for electrode materials produced using PET. Besides, PET-derived materials' electrochemical performance in supercapacitor application is likewise broken down, with an emphasis on key electrochemical boundaries like capacitive behaviour, cyclic stability, and electrochemical impedance spectroscopy. The need for scalable and cost-effective recycling methods, the creation of eco-friendly electrolytes, and the improvement of the electrochemical performance of recycled PET-based supercapacitors are just a few of the issues and opportunities highlighted in this expanding eco-friendly industry. Overall, the goal of this review is to provide a comprehensive understanding of the cutting-edge developments in the use of recycled PETW as a precursor for supercapacitor electrodes, highlighting the eco-friendly energy storage solution's potential and contributing to a sustainable future.

Insights into properties, synthesis and emerging applications of polypyrrole-based composites, and future prospective: A review

Recent advancements in polymer science and engineering underscore the importance of creating sophisticated soft materials characterized by well-defined structures and adaptable properties to meet the demands of emerging applications. The primary objective of polymeric composite technology is to enhance the functional utility of materials for high-end purposes. Both the inherent qualities of the materials and the intricacies of the synthesis process play pivotal roles in advancing their properties and expanding their potential applications. Polypyrrole (PPy)-based composites, owing to their distinctive properties, hold great appeal for a variety of applications. Despite the limitations of PPy in its pure form, these constraints can be effectively overcome through hybridization with other materials. This comprehensive review thoroughly explores the existing literature on PPy and PPy-based composites, providing in-depth insights into their synthesis, properties, and applications. Special attention is given to the advantages of intrinsically conducting polymers (ICPs) and PPy in comparison to other ICPs. The impact of doping anions, additives, and oxidants on the properties of PPy is also thoroughly examined. By delving into these aspects, this overview aims to inspire researchers to delve into the realm of PPy-based composites, encouraging them to explore new avenues for flexible technology applications.

Advancing chirality analysis through enhanced enantiomer characterization and quantification via fast Fourier transform capacitance voltammetry

The exploration of the chiral configurations of enantiomers represents a highly intriguing realm of scientific inquiry due to the distinct roles played by each enantiomer (D and L) in chemical reactions and their practical utilities. This study introduces a pioneering analytical methodology, termed fast Fourier transform capacitance voltammetry (FFT-CPV), in conjunction with principal component analysis (PCA), for the identification and quantification of the chiral forms of tartaric acid (TA), serving as a representative model system for materials exhibiting pronounced chiral characteristics. The proposed methodology relies on the principle of chirality, wherein the capacitance signal generated by the adsorption of D-TA and L-TA onto the surface of a platinum electrode (Pt-electrode) in an acidic solution is harnessed. The capacitance voltammograms were meticulously recorded under optimized experimental conditions. To compile the final dataset for the analyte, the average of the FFT capacitance voltammograms of the acidic solution (without the presence of the analyte) was subtracted from those containing the analyte. A distinct arrangement was obtained by employing PCA as a linear data transformation method, representing D-TA and L-TA in a two/three-dimensional space. The outcomes of the study reveal the successful detection of the two chiral forms of TA with a considerable degree of precision and reproducibility. Moreover, the proposed method facilitated the establishment of two linear response ranges for the concentration values of each enantiomer, spanning from 1 to 20 µM, and 50 to 500 µM. The respective detection limits were also determined to be 0.4 µM for L-TA and 1.3 µM for D-TA. These findings underscore the satisfactory sensitivity and efficiency of the proposed method in both qualitative and quantitative assessments of the chiral forms of TA.

In situ synthesis and dynamic simulation of molecularly imprinted polymeric nanoparticles on a micro-reactor system

Current practices in synthesizing molecularly imprinted polymers face challenges-lengthy process, low-productivity, the need for expensive and sophisticated equipment, and they cannot be controlled in situ synthesis. Herein, we present a micro-reactor for in situ and continuously synthesizing trillions of molecularly imprinted polymeric nanoparticles that contain molecular fingerprints of bovine serum albumin in a short period of time (5-30 min). Initially, we performed COMSOL simulation to analyze mixing efficiency with altering flow rates, and experimentally validated the platform for synthesizing nanoparticles with sizes ranging from 52-106 nm. Molecular interactions between monomers and protein were also examined by molecular docking and dynamics simulations. Afterwards, we benchmarked the micro-reactor parameters through dispersity and concentration of molecularly imprinted polymers using principal component analysis. Sensing assets of molecularly imprinted polymers were examined on a metamaterial sensor, resulting in 81% of precision with high selectivity (4.5 times), and three cycles of consecutive use. Overall, our micro-reactor stood out for its high productivity (48-288 times improvement in assay-time and 2 times improvement in reagent volume), enabling to produce 1.4-1.5 times more MIPs at one-single step, and continuous production compared to conventional strategy.

Ag(e)ing and Degradation of Supercapacitors: Causes, Mechanisms, Models and Countermeasures

The most prominent and highly visible advantage attributed to supercapacitors of any type and application, beyond their most notable feature of high current capability, is their high stability in terms of lifetime, number of possible charge/discharge cycles or other stability-related properties. Unfortunately, actual devices show more or less pronounced deterioration of performance parameters during time and use. Causes for this in the material and component levels, as well as on the device level, have only been addressed and discussed infrequently in published reports. The present review attempts a complete coverage on these levels; it adds in modelling approaches and provides suggestions for slowing down ag(e)ing and degradation.

Molecularly Imprinted Polymer-Based Electrochemical Sensors for the Diagnosis of Infectious Diseases

The appearance of biological molecules, so-called biomarkers in body fluids at abnormal concentrations, is considered a good tool for detecting disease. Biomarkers are usually looked for in the most common body fluids, such as blood, nasopharyngeal fluids, urine, tears, sweat, etc. Even with significant advances in diagnostic technology, many patients with suspected infections receive empiric antimicrobial therapy rather than appropriate treatment, which is driven by rapid identification of the infectious agent, leading to increased antimicrobial resistance. To positively impact healthcare, new tests are needed that are pathogen-specific, easy to use, and produce results quickly. Molecularly imprinted polymer (MIP)-based biosensors can achieve these general goals and have enormous potential for disease detection. This article aimed to overview recent articles dedicated to electrochemical sensors modified with MIP to detect protein-based biomarkers of certain infectious diseases in human beings, particularly the biomarkers of infectious diseases, such as HIV-1, COVID-19, Dengue virus, and others. Some biomarkers, such as C-reactive protein (CRP) found in blood tests, are not specific for a particular disease but are used to identify any inflammation process in the body and are also under consideration in this review. Other biomarkers are specific to a particular disease, e.g., SARS-CoV-2-S spike glycoprotein. This article analyzes the development of electrochemical sensors using molecular imprinting technology and the used materials' influence. The research methods, the application of different electrodes, the influence of the polymers, and the established detection limits are reviewed and compared.

Electric Field-Assisted Uptake of Hexavalent Chromium Ions with In Situ Regeneration of Carbon Monolith Adsorbents

The uptake of hexavalent chromium (Cr(VI)) ions from wastewater is of great significance for environmental remediation and resource utilization. In this study, a self-designed instrument equipped with an oxidized mesoporous carbon monolith (o-MCM) as an electro-adsorbent is developed. o-MCM with a super hydrophilic surface displayed a high specific surface area (up to 686.5 m²  g^-1 ). With the assistance of an electric field (0.5 V), the removal capacity of Cr(VI) ions is as high as 126.6 mg g^-1 , much higher than that without an electric field (49.5 mg g^-1 ). During this process, no reduction reaction of Cr(VI) to Cr(III) ions is observed. After adsorption, the reverse electrode with 10 V is used to efficiently desorb the ions on the carbon surface. Meanwhile, the in situ regeneration of carbon adsorbents can be obtained even after ten recycles. On this basis, the enrichment of Cr(VI) ions in a special solution is achieved with the assistance of an electric field. This work lays a foundation for the uptake of heavy metal ions from wastewater with the assistance of the electric field.

Molecularly Imprinted Polymers for the Determination of Cancer Biomarkers

Biomarkers can provide critical information about cancer and many other diseases; therefore, developing analytical systems for recognising biomarkers is an essential direction in bioanalytical chemistry. Recently molecularly imprinted polymers (MIPs) have been applied in analytical systems to determine biomarkers. This article aims to an overview of MIPs used for the detection of cancer biomarkers, namely: prostate cancer (PSA), breast cancer (CA15-3, HER-2), epithelial ovarian cancer (CA-125), hepatocellular carcinoma (AFP), and small molecule cancer biomarkers (5-HIAA and neopterin). These cancer biomarkers may be found in tumours, blood, urine, faeces, or other body fluids or tissues. The determination of low concentrations of biomarkers in these complex matrices is technically challenging. The overviewed studies used MIP-based biosensors to assess natural or artificial samples such as blood, serum, plasma, or urine. Molecular imprinting technology and MIP-based sensor creation principles are outlined. Analytical signal determination methods and the nature and chemical structure of the imprinted polymers are discussed. Based on the reviewed biosensors, the results are compared, and the most suitable materials for each biomarker are discussed.

Real-Time Monitoring of Biofilm Formation Using a Noninvasive Impedance-Based Method

Biofilms are complex three-dimensional microbial communities that adhere to a variety of surfaces and interact with their surroundings. Because of the dynamic nature of biofilm formation, establishing a uniform technique for quantifying and monitoring biofilm volume, shape, and features in real-time is challenging. Herein, we describe a noninvasive electrochemical impedance approach for real-time monitoring of dental plaque-derived multispecies biofilm growth on a range of substrates. A working equation relating electrochemical impedance to live biofilm volume has been developed that is applicable to all three surfaces examined, including glass, dental filling resin, and Ca2+-releasing resin composites. Impedance changes of 2.5, 35, 50, and 65% correlated to biofilm volumes of 0.10 ± 0.01, 16.9 ± 2.2, 29.7 ± 2.3, and 38.6 ± 2.8 μm3/μm2, respectively. We discovered that glass, dental filling resin, and Ca2+-releasing dental composites required approximately 3.5, 4.5, and 6 days, respectively, to achieve a 50% change in impedance. The local pH change at the biofilm-substrate interfaces also monitored with potentiometry pH microsensor, and pH change varied according to biofilm volume. This impedance-based technique can be a useful analytical method for monitoring the growth of biofilms on a variety of substrates in real-time. Therefore, this technique may be beneficial for examining antibacterial properties of novel biomaterials.

Development of an inexpensive and rapidly preparable enzymatic pencil graphite biosensor for monitoring of glyphosate in waters

Glyphosate (GLY) is the most widely used non-selective broad-spectrum herbicide worldwide under well-reported side effects on the environment and human health. That's why it's necessary to control its presence in the environment. This work describes the development of an affordable, simple, and accurate electrochemical biosensor using a pencil graphite electrode as support, a horseradish peroxidase enzyme immobilized on a polysulfone membrane doped with multi-walled carbon nanotubes. The developed electrochemical sensor was used in the determination of GLY in river and drinking water samples. Cyclic voltammetry and amperometry were used as electrochemical detection techniques for the characterization and analytical application of the developed biosensor. The working mechanism of the biosensor is based on the inhibition of the peroxidase enzyme by GLY. Under optimal experimental conditions, the biosensor showed a linear response in the concentration range of 0.1 to 10 mg L^-1. The limits of detection and quantification are 0.025 ± 0.002 and 0.084 ± 0.007 mg L^-1, respectively, which covers the maximum residual limit established by the EPA for drinking water (0.7 mg L^-1). The proposed biosensor demonstrated high reproducibility, excellent analytical performance, repeatability, and accuracy. The sensor proved to be selective against other pesticides, organic acids, and inorganic salts. Application on real samples showed recovery rates ranging between 98.18 ± 0.11 % and 97.32 ± 0.23 %. The analytical features of the proposed biosensor make it an effective and useful tool for the detection of GLY for environmental analysis.

Emphasis on the incorporation of Tropaeolin OO dye and silver nanoparticles for voltammetric estimation of flibanserin in bulk form, tablets and human plasma

A novel electrochemical sensor based on the electro-deposition of silver nanoparticles (AgNPs) on Tropaeolin OO (poly-TO) layers over pencil graphite electrode (PGE) surface was fabricated for the first time for voltammetric determination of flibanserin (FBS); a drug enhances female sexual performance. Further characterization studies using cyclic voltammetry (CV), square wave voltammetry (SWV), electrochemical impedance spectroscopy (EIS) and scanning electron microscopy (SEM) were conducted. The AgNPs synergistic effect on poly-TO layers facilitates the FBS electro-oxidation in phosphate buffer solution (pH 6.0) and its determination in bulk form, tablets and in human plasma. Following ICH guidelines, validation of the proposed SWV method for FBS analysis was successfully achieved using the fabricated sensor (AgNPs@poly-TO/PGE). Under the optimal instrumental and experimental conditions, the anodic oxidation peak current was directly proportional to FBS concentration in the range from 0.1 to 8.5 μmol L^-1 with low detection and quantitation limits (0.0286 and 0.0867 μmol L^-1, respectively). High sensitivity, selectivity as well as easiness of fabrication are the main advantages of the modified sensor.

Carbon Nanotubes-Based Fuel Cell for Cr(VI) Removal and Electricity Generation

A fuel cell, an energy transducer, can convert chemical energy into electrical energy. In this work, graphite felt (GF) loaded with polypyrrole (PPy) and carboxylic carbon nanotubes (CNTs-COOH) was used as a cathode (GF/PPy/CNTs-COOH) in a double-chamber nonbiofuel cell (D-nBFC) to remove Cr(VI) efficiently. Therein, Na₂S₂O₃ in an alkaline solution and Cr(VI) in a strongly acidic solution were employed as anode and cathode solutions, respectively. An agar salt bridge, consisting of saturated KCl solution, was used to transport ions between the anode and cathode. This system suggested that the removal efficiency of Cr(VI) could reach 99.6%. The maximum current, power, and power density could achieve 136.8 μA, 18.7 μW, and 20.8 mW/m² at 90 min, respectively. Additionally, GF/PPy/CNTs-COOH also had good electrocatalytic stability and reusability after four cycles, which played an important role in the development of the D-nBFC system. Therefore, this study provides an environmentally friendly and efficient method to remove Cr(VI) and generate electricity simultaneously.

Conducting Polymers for the Design of Tactile Sensors

This paper provides an overview of the application of conducting polymers (CPs) used in the design of tactile sensors. While conducting polymers can be used as a base in a variety of forms, such as films, particles, matrices, and fillers, the CPs generally remain the same. This paper, first, discusses the chemical and physical properties of conducting polymers. Next, it discusses how these polymers might be involved in the conversion of mechanical effects (such as pressure, force, tension, mass, displacement, deformation, torque, crack, creep, and others) into a change in electrical resistance through a charge transfer mechanism for tactile sensing. Polypyrrole, polyaniline, poly(3,4-ethylenedioxythiophene), polydimethylsiloxane, and polyacetylene, as well as application examples of conducting polymers in tactile sensors, are overviewed. Attention is paid to the additives used in tactile sensor development, together with conducting polymers. There is a long list of additives and composites, used for different purposes, namely: cotton, polyurethane, PDMS, fabric, Ecoflex, Velostat, MXenes, and different forms of carbon such as graphene, MWCNT, etc. Some design aspects of the tactile sensor are highlighted. The charge transfer and operation principles of tactile sensors are discussed. Finally, some methods which have been applied for the design of sensors based on conductive polymers, are reviewed and discussed.

Development of molecularly imprinted polymer based phase boundaries for sensors design (review)

Achievements in polymer chemistry enables to design artificial phase boundaries modified by imprints of selected molecules and some larger structures. These structures seem very useful for the design of new materials suitable for affinity chromatography and sensors. In this review, we are overviewing the synthesis of molecularly imprinted polymers (MIPs) and the applicability of these MIPs in the design of affinity sensors. Such MIP-based layers or particles can be used as analyte-recognizing parts for sensors and in some cases they can replace very expensive compounds (e.g.: antibodies, receptors etc.), which are recognizing analyte. Many different polymers can be used for the formation of MIPs, but conducing polymers shows the most attractive capabilities for molecular-imprinting by various chemical compounds. Therefore, the application of conducting polymers (e.g.: polypyrrole, polyaniline, polythiophene, poly(3,4-ethylenedioxythiophene), and ortho-phenylenediamine) seems very promising. Polypyrrole is one of the most suitable for the development of MIP-based structures with molecular imprints by analytes of various molecular weights. Overoxiation of polypyrrole enables to increase the selectivity of polypyrrole-based MIPs. Methods used for the synthesis of conducting polymer based MIPs are overviewed. Some methods, which are applied for the transduction of analytical signal, are discussed, and challenges and new trends in MIP-technology are foreseen.

Electrochemical Determination of Interaction between SARS-CoV-2 Spike Protein and Specific Antibodies

The serologic diagnosis of coronavirus disease 2019 (COVID-19) and the evaluation of vaccination effectiveness are identified by the presence of antibodies specific to severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). In this paper, we present the electrochemical-based biosensing technique for the detection of antibodies specific to the SARS-CoV-2 proteins. Recombinant SARS-CoV-2 spike proteins (rSpike) were immobilised on the surface of a gold electrode modified by a self-assembled monolayer (SAM). This modified electrode was used as a sensitive element for the detection of polyclonal mouse antibodies against the rSpike (anti-rSpike). Electrochemical impedance spectroscopy (EIS) was used to observe the formation of immunocomplexes while cyclic voltammetry (CV) was used for additional analysis of the surface modifications. It was revealed that the impedimetric method and the elaborate experimental conditions are appropriate for the further development of electrochemical biosensors for the serological diagnosis of COVID-19 and/or the confirmation of successful vaccination against SARS-CoV-2.

Biosensors Based on Bio-Functionalized Semiconducting Metal Oxides

Immobilization of biomaterials is a very important task in the development of biofuel cells and biosensors. Some semiconducting metal-oxide-based supporting materials can be used in these bioelectronics-based devices. In this article, we are reviewing some functionalization methods that are applied for the immobilization of biomaterials. The most significant attention is paid to the immobilization of biomolecules on the surface of semiconducting metal oxides. The improvement of biomaterials immobilization on metal oxides and analytical performance of biosensors by coatings based on conducting polymers, self-assembled monolayers and lipid membranes is discussed.

Electrochemical Determination of Interaction between SARS-CoV-2 Spike Protein and Specific Antibodies

The serologic diagnosis of coronavirus disease 2019 (COVID-19) and the evaluation of vaccination effectiveness are identified by the presence of antibodies specific to severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). In this paper, we present the electrochemical-based biosensing technique for the detection of antibodies specific to the SARS-CoV-2 proteins. Recombinant SARS-CoV-2 spike proteins (rSpike) were immobilised on the surface of a gold electrode modified by a self-assembled monolayer (SAM). This modified electrode was used as a sensitive element for the detection of polyclonal mouse antibodies against the rSpike (anti-rSpike). Electrochemical impedance spectroscopy (EIS) was used to observe the formation of immunocomplexes while cyclic voltammetry (CV) was used for additional analysis of the surface modifications. It was revealed that the impedimetric method and the elaborate experimental conditions are appropriate for the further development of electrochemical biosensors for the serological diagnosis of COVID-19 and/or the confirmation of successful vaccination against SARS-CoV-2.

Towards electrochemical surface plasmon resonance sensor based on the molecularly imprinted polypyrrole for glyphosate sensing

In this research the molecular imprinting technology was applied for the formation of glyphosate-sensitive layer. The glyphosate imprinted conducting polymer polypyrrole (MIPpy) was deposited on a gold chip/electrode and used as an electrochemical surface plasmon resonance (ESPR) sensor. The results described in this study disclose some restrictions and challenges, which arise during the development of glyphosate ESPR sensor based on the molecularly imprinted polymer development stage. It was demonstrated, that glyphosate could significantly affect the electrochemical deposition process of molecularly imprinted polymer on the electrode. The results of cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and surface plasmon resonance (SPR) have demonstrated that glyphosate molecules tend to interact with bare gold electrode and thus hinder the polypyrrole deposition. As a possible solution, the formation of a self-assembled monolayer (SAM) of 11-(1H-Pyrrol-1-yl)undecane-1-thiol (PUT) before electrochemical deposition of MIPpy and NIPpy was applied. Dissociation constant (KD) and free energy of Gibbs (ΔG0) values of glyphosate on MIPpy and Ppy without glyphosate imprints (NIPpy) were calculated. For the interaction of glyphosate with MIPpy the KD was determined as 38.18 ± 2.33⋅10-5 and ΔG0 as -19.51 ± 0.15 kJ/mol.

Effect of Oxidizer on PANI for Producing BaTiO3@PANI Perovskite Composites and Their Electrical and Electrochemical Properties

Polyaniline (PANI) has received significant attention in basic and applied studies because it has electrical and electrochemical properties comparable to conventional semiconductors and metals. PANI's electrical and electrochemical properties can be controlled through its preparation methods. Accordingly, in the present work, two different samples of PANI were prepared by the polymerization of aniline monomer via in situ polymerization method using two different oxidizers of dichromate (PANI (1)) and persulphate (PANI (2)). The products were blended with BaTiO3 (BTO) to form BTO@PANI composites. The composites were characterized by scanning electron microscopy (SEM), Fourier transforms infrared spectroscopy (FTIR), X-ray powder diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). SEM illustrated the covering of PANI layers on the BTO nanoparticles. The electrical and electrochemical properties of the prepared composites were studied. The BTO@PANI(2) composite sample showed a conductivity of 1.2 × 10–3 S/cm higher than that found for each BTO@PANI(1) 9.1 × 10–4 S/cm and its constituents. The supercapacity showed higher capacity values of 70 F/g, and 76 F/g for BTO@PANI(1), and BTO@PANI(2), respectively, which are higher than its constituents.

Electrochemically Deposited Molecularly Imprinted Polymer-Based Sensors

This review is dedicated to the development of molecularly imprinted polymers (MIPs) and the application of MIPs in sensor design. MIP-based biological recognition parts can replace receptors or antibodies, which are rather expensive. Conducting polymers show unique properties that are applicable in sensor design. Therefore, MIP-based conducting polymers, including polypyrrole, polythiophene, poly(3,4-ethylenedioxythiophene), polyaniline and ortho-phenylenediamine are frequently applied in sensor design. Some other materials that can be molecularly imprinted are also overviewed in this review. Among many imprintable materials conducting polymer, polypyrrole is one of the most suitable for molecular imprinting of various targets ranging from small organics up to rather large proteins. Some attention in this review is dedicated to overview methods applied to design MIP-based sensing structures. Some attention is dedicated to the physicochemical methods applied for the transduction of analytical signals. Expected new trends and horizons in the application of MIP-based structures are also discussed.

Biosensors for the Determination of SARS-CoV-2 Virus and Diagnosis of COVID-19 Infection

Monitoring and tracking infection is required in order to reduce the spread of the coronavirus disease 2019 (COVID-19), induced by severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). To achieve this goal, the development and deployment of quick, accurate, and sensitive diagnostic methods are necessary. The determination of the SARS-CoV-2 virus is performed by biosensing devices, which vary according to detection methods and the biomarkers which are inducing/providing an analytical signal. RNA hybridisation, antigen-antibody affinity interaction, and a variety of other biological reactions are commonly used to generate analytical signals that can be precisely detected using electrochemical, electrochemiluminescence, optical, and other methodologies and transducers. Electrochemical biosensors, in particular, correspond to the current trend of bioanalytical process acceleration and simplification. Immunosensors are based on the determination of antigen-antibody interaction, which on some occasions can be determined in a label-free mode with sufficient sensitivity.

Evaluation of Electrochromic Properties of Polypyrrole/Poly(Methylene Blue) Layer Doped by Polysaccharides

Polypyrrole (Ppy) and poly(methylene blue) (PMB) heterostructure (Ppy-PMB) was electrochemically formed on the indium tin oxide (ITO) coated glass slides, which served as working electrodes. For electropolymerization, a solution containing pyrrole, methylene blue, and a saccharide (lactose, sucrose, or heparin) that served as dopant was used. The aim of this study was to compare the effect of the saccharides (lactose, sucrose, and heparin) on the electrochromic properties of the Ppy-PMB layer. AFM and SEM have been used for the analysis of the surface dominant features of the Ppy-PMB layers. From these images, it was concluded that the saccharides used in this study have a moderate effect on the surface morphology. Electrochromic properties were analyzed with respect to the changes of absorbance of the layer at two wavelengths (668 nm and 750 nm) by changing the pH of the surrounding solution and the potential between +0.8 V and -0.8 V. It was demonstrated that the highest absorbance changes are characteristic for all layers in the acidic media. Meanwhile, the absorbance changes of the layers were decreased in the more alkaline media. It was determined that the Ppy-PMB layers with heparin as a dopant were more mechanically stable in comparison to the layers doped with lactose and sucrose. Therefore, the Ppy-PMB layer doped with heparin was selected for the further experiment and it was applied in the design of electrochromic sensors for the determination of three xanthine derivatives: caffeine, theobromine, and theophylline. A linear relationship of ΔA (∆A = A_+0.8V - A_-0.8V) vs. concentration was determined for all three xanthine derivatives studied. The largest change in optical absorption was observed in the case of theophylline determination.

Solvent Effect in Imidazole-Based Poly(Ionic liquid) Membranes: Energy Storage and Sensing

Polymerized ionic liquids (PILs) are interesting new materials in sustainable technologies for energy storage and for gas sensor devices, and they provide high ion conductivity as solid polymer electrolytes in batteries. We introduce here the effect of polar protic (aqueous) and polar aprotic (propylene carbonate, PC) electrolytes, with the same concentration of lithium bis(trifluoromethane) sulfonimide (LiTFSI) on hydrophobic PIL films. Cyclic voltammetry, scanning ionic conductance microscopy and square wave voltammetry were performed, revealing that the PIL films had better electroactivity in the aqueous electrolyte and three times higher ion conductivity was obtained from electrochemical impedance spectroscopy measurements. Their energy storage capability was investigated with chronopotentiometric measurements, and it revealed 1.6 times higher specific capacitance in the aqueous electrolyte as well as novel sensor properties regarding the applied solvents. The PIL films were characterized with scanning electron microscopy, energy dispersive X-ray, FTIR and solid state nuclear magnetic resonance spectroscopy.

Design and Fabrication of a Fast Response Resistive-Type Humidity Sensor Using Polypyrrole (Ppy) Polymer Thin Film Structures

In this research article, an organic polymer based polypyrrole (Ppy) composite material has been synthesized and analyzed for the design and fabrication purposes of a fast-responsive, highly sensitive, and an economical resistive-type novel humidity detection sensor. This humidity sensor most suitably serves the purpose for industrial humidity (i.e., values ranging from low to high) detection applications. First, a polypyrrole composite material (a mixture of polypyrrole, polypyrrole-NiO, polypyrrole-CeO₂, and polypyrrole-Nb₂O₅) has been synthesized by chemical oxidative polymerization method, and then is treated at various temperatures, i.e., 100, 150 and 200 °C, respectively. After this treatment, the synthesized samples were then characterized by using FTIR, SEM, and DTA/TGA techniques for analyzing humidity sensing properties. The polypyrrole samples with the best morphological structure and properties were then incorporated on interdigitated electrodes. For the fabrication purposes of this thin film structure, at first a few drops of polyvinyl alcohol (PVA) were placed over interdigitated electrodes (IDE) and then the synthesized polypyrrole composite was uniformly deposited in the form of a thin film over it. The plots show that this is a good resistive-type humidity detection device for the relative humidity range of 30% to 90%. The response and recovery times of this newly fabricated humidity sensor were reported to be the same as 128 s at room temperature. Additionally, the stability and the repeatability response behavior of this Ppy sensor were verified up to five cycles of multiple repetitions. This presents an excellent stability and repeatability performance of the sensor. Furthermore, the capacitances versus humidity response and recovery properties of the designed sensor were studied too. This illustrates an excellent capacitive verses humidity response and shows a linear and an active behavior. Lastly, the experimental result proves that polypyrrole composite thin film shows a reasonable best performance up to a temperature of 100 °C.

Affinity Sensors for the Diagnosis of COVID-19

The coronavirus disease 2019 (COVID-19) outbreak caused by severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) was proclaimed a global pandemic in March 2020. Reducing the dissemination rate, in particular by tracking the infected people and their contacts, is the main instrument against infection spreading. Therefore, the creation and implementation of fast, reliable and responsive methods suitable for the diagnosis of COVID-19 are required. These needs can be fulfilled using affinity sensors, which differ in applied detection methods and markers that are generating analytical signals. Recently, nucleic acid hybridization, antigen-antibody interaction, and change of reactive oxygen species (ROS) level are mostly used for the generation of analytical signals, which can be accurately measured by electrochemical, optical, surface plasmon resonance, field-effect transistors, and some other methods and transducers. Electrochemical biosensors are the most consistent with the general trend towards, acceleration, and simplification of the bioanalytical process. These biosensors mostly are based on the determination of antigen-antibody interaction and are robust, sensitive, accurate, and sometimes enable label-free detection of an analyte. Along with the specification of biosensors, we also provide a brief overview of generally used testing techniques, and the description of the structure, life cycle and immune host response to SARS-CoV-2, and some deeper details of analytical signal detection principles.

Advances in Molecularly Imprinted Polymers Based Affinity Sensors (Review)

Recent challenges in biomedical diagnostics show that the development of rapid affinity sensors is very important issue. Therefore, in this review we are aiming to outline the most important directions of affinity sensors where polymer-based semiconducting materials are applied. Progress in formation and development of such materials is overviewed and discussed. Some applicability aspects of conducting polymers in the design of affinity sensors are presented. The main attention is focused on bioanalytical application of conducting polymers such as polypyrrole, polyaniline, polythiophene and poly(3,4-ethylenedioxythiophene) ortho-phenylenediamine. In addition, some other polymers and inorganic materials that are suitable for molecular imprinting technology are also overviewed. Polymerization techniques, which are the most suitable for the development of composite structures suitable for affinity sensors are presented. Analytical signal transduction methods applied in affinity sensors based on polymer-based semiconducting materials are discussed. In this review the most attention is focused on the development and application of molecularly imprinted polymer-based structures, which can replace antibodies, receptors, and many others expensive affinity reagents. The applicability of electrochromic polymers in affinity sensor design is envisaged. Sufficient biocompatibility of some conducting polymers enables to apply them as "stealth coatings" in the future implantable affinity-sensors. Some new perspectives and trends in analytical application of polymer-based semiconducting materials are highlighted.

Effects of Counter Anions on AC and DC Electrical Conductivity in Poly(Dimethylsiloxane) Crosslinked by Metal-Ligand Coordination

There is an urgent need for the development of elastic dielectric materials for flexible organic field effect transistors (OFETs). In this work, detailed analysis of the AC and DC electrical conductivity of a series of flexible poly(dimethylsiloxane) (PDMS) polymers crosslinked by metal-ligand coordination in comparison to neat PDMS was performed for the first time by means of broadband dielectric spectroscopy. The ligand was 2,2-bipyridine-4,4-dicarboxylic amide, and Ni²⁺, Mn²⁺, and Zn²⁺ were introduced for Cl⁻, Br⁻, and I⁻ salts. Introduction of metal salt and creation of coordination bonds resulted in higher permittivity values increasing in an order: neat PDMS < Ni²⁺ < Mn²⁺ < Zn²⁺; accompanied by conductivity values of the materials increasing in an order: neat PDMS < Cl⁻ < I⁻ < Br⁻. Conductivity relaxation time plot as a function of temperature, showed Vogel-Fulcher–Tammann dependance for the Br⁻ salts and Arrhenius type for the Cl⁻ and I⁻ salts. Performed study revealed that double-edged challenge can be obtained, i.e., dielectric materials with elevated value of dielectric permittivity without deterioration too much the non-conductive nature of the polymer. This opens up new perspectives for the production of flexible dielectrics suitable for gate insulators in OFETs. Among the synthesized organometallic materials, those with chlorides salts are the most promising for such applications.

Charge Transfer and Biocompatibility Aspects in Conducting Polymer-Based Enzymatic Biosensors and Biofuel Cells

Charge transfer (CT) is a very important issue in the design of biosensors and biofuel cells. Some nanomaterials can be applied to facilitate the CT in these bioelectronics-based devices. In this review, we overview some CT mechanisms and/or pathways that are the most frequently established between redox enzymes and electrodes. Facilitation of indirect CT by the application of some nanomaterials is frequently applied in electrochemical enzymatic biosensors and biofuel cells. More sophisticated and still rather rarely observed is direct charge transfer (DCT), which is often addressed as direct electron transfer (DET), therefore, DCT/DET is also targeted and discussed in this review. The application of conducting polymers (CPs) for the immobilization of enzymes and facilitation of charge transfer during the design of biosensors and biofuel cells are overviewed. Significant attention is paid to various ways of synthesis and application of conducting polymers such as polyaniline, polypyrrole, polythiophene poly(3,4-ethylenedioxythiophene). Some DCT/DET mechanisms in CP-based sensors and biosensors are discussed, taking into account that not only charge transfer via electrons, but also charge transfer via holes can play a crucial role in the design of bioelectronics-based devices. Biocompatibility aspects of CPs, which provides important advantages essential for implantable bioelectronics, are discussed.

Conducting Polymers in the Design of Biosensors and Biofuel Cells

Fast and sensitive determination of biologically active compounds is very important in biomedical diagnostics, the food and beverage industry, and environmental analysis. In this review, the most promising directions in analytical application of conducting polymers (CPs) are outlined. Up to now polyaniline, polypyrrole, polythiophene, and poly(3,4-ethylenedioxythiophene) are the most frequently used CPs in the design of sensors and biosensors; therefore, in this review, main attention is paid to these conducting polymers. The most popular polymerization methods applied for the formation of conducting polymer layers are discussed. The applicability of polypyrrole-based functional layers in the design of electrochemical biosensors and biofuel cells is highlighted. Some signal transduction mechanisms in CP-based sensors and biosensors are discussed. Biocompatibility-related aspects of some conducting polymers are overviewed and some insights into the application of CP-based coatings for the design of implantable sensors and biofuel cells are addressed. New trends and perspectives in the development of sensors based on CPs and their composites with other materials are discussed.

Formation and Electrochemical Evaluation of Polyaniline and Polypyrrole Nanocomposites Based on Glucose Oxidase and Gold Nanostructures

Nanocomposites based on two conducting polymers, polyaniline (PANI) and polypyrrole (Ppy), with embedded glucose oxidase (GOx) and 6 nm size gold nanoparticles (AuNPs_(6nm)) or gold-nanoclusters formed from chloroaurate ions (AuCl₄⁻), were synthesized by enzyme-assisted polymerization. Charge (electron) transfer in systems based on PANI/AuNPs_(6nm)-GOx, PANI/AuNPs_(AuCl4⁻₎-GOx, Ppy/AuNPs_(6nm)-GOx and Ppy/AuNPs_(AuCl4⁻₎-GOx nanocomposites was investigated. Cyclic voltammetry (CV)-based investigations showed that the reported polymer nanocomposites are able to facilitate electron transfer from enzyme to the graphite rod (GR) electrode. Significantly higher anodic current and well-defined red-ox peaks were observed at a scan rate of 0.10 V s⁻¹. Logarithmic function of anodic current (log I_pa), which was determined by CV-based experiments performed with glucose, was proportional to the logarithmic function of a scan rate (log v) in the range of 0.699–2.48 mV s⁻¹, and it indicates that diffusion-controlled electrochemical processes were limiting the kinetics of the analytical signal. The most efficient nanocomposite structure for the design of the reported glucose biosensor was based on two-day formed Ppy/AuNPs_(AuCl4⁻₎-GOx nanocomposites. GR/Ppy/AuNPs_(AuCl4⁻₎-GOx was characterized by the linear dependence of the analytical signal on glucose concentration in the range from 0.1 to 0.70 mmol L⁻¹, the sensitivity of 4.31 mA mM cm⁻², the limit of detection of 0.10 mmol L⁻¹ and the half-life period of 19 days.

Polyethylene-Carbon Composite (Velostat®) Based Tactile Sensor

The progress observed in ‘soft robotics’ brought some promising research in flexible tactile, pressure and force sensors, which can be based on polymeric composite materials. Therefore, in this paper, we intend to evaluate the characteristics of a force-sensitive material—polyethylene-carbon composite (Velostat^®) by implementing this material into the design of the flexible tactile sensor. We have explored several possibilities to measure the electrical signal and assessed the mechanical and time-dependent properties of this tactile sensor. The response of the sensor was evaluated by performing tests in static, long-term load and cyclic modes. Experimental results of loading cycle measurements revealed the hysteresis and nonlinear properties of the sensor. The transverse resolution of the sensor was defined by measuring the response of the sensor at different distances from the loaded point. Obtained dependencies of the sensor’s sensitivity, hysteresis, response time, transversal resolution and deformation on applied compressive force promise a practical possibility to use the polyethylene-carbon composite as a sensitive material for sensors with a single electrode pair or its matrix. The results received from experimental research have defined the area of the possible implementation of the sensor based on a composite material—Velostat^®.