Some possibilities to reduce the biofilm formation on transparent siloxane coatings

Fucoidan-Containing, Low-Adhesive Siloxane Coatings for Medical Applications: Inhibition of Bacterial Growth and Biofilm Development

The deposition of low-adhesive siloxane coatings is a current trend for the non-toxic control of bacterial growth and biofilm formation. Total elimination of biofilm formation has not been reported so far. The aim of this investigation was to study the ability of a non-toxic, natural, biologically active substance, such as fucoidan, to inhibit bacterial growth on similar medical coatings. The fucoidan amount was varied, and its impact on the bioadhesion-influencing surface characteristics, as well as on bacterial cell growth, was investigated. The inclusion of up to 3-4 wt.% brown algae-derived fucoidan in the coatings increases their inhibitory effect, more significantly on the Gram-positive bacterium S. aureus than on the Gram-negative bacterium Escherichia coli. The biological activity of the studied siloxane coatings was ascribed to the formation of a low-adhesive, biologically active surface top layer consisting of siloxane oil and dispersed water-soluble fucoidan particles. This is the first report on the antibacterial activity of fucoidan-containing medical siloxane coatings. The experimental results give reason to expect that relevantly selected, natural biologically active substances can be efficient in the non-toxic control of bacterial growth on medical devices and, as a result, medical device-associated infections.

Comparative Study of the Marinobacter hydrocarbonoclasticus Biofilm Formation on Antioxidants Containing Siloxane Composite Coatings

No systematic study of antioxidant containing coatings and their anti-biofilm action has been reported so far. The utilization of antioxidants in protective coatings to inhibit marine biofilm formation is a current challenge. The aim of this preliminary study was to prepare, characterize and compare the efficiency of low adhesive siloxane composite coatings equally loaded with different antioxidants against mono-species biofilms formation. Most often participating in the marine biofilms formation, Marinobacter hydrocarbonoclasticus was the test bacterium. Both the biofilm covered surface area (BCSA) and corrected total cell fluorescence (CTCF) (by fluorescent microscopy) were selected as the parameters for quantification of the biofilm after 1 h and 4 h incubation. Differing extents of altered surface characteristics (physical-chemical; physical-mechanical) and the specific affection of M. hydrocarbonoclasticus biofilm formation in both reduction and stimulation, were found in the studied antioxidant containing coatings, depending on the chemical nature of the used antioxidant. It was concluded that not all antioxidants reduce mono-species biofilm formation; antioxidant chemical reactivity stipulates the formation of an altered vulcanization network of the siloxane composites and thus microbial adhesion which influences the surface characteristics of the vulcanized coatings; and low surface energy combined with a low indentation elastic modulus are probably pre-requisites of low microbial adhesion.

Materials Selection for Antifouling Systems in Marine Structures

Fouling is the accumulation of unwanted substances, such as proteins, organisms, and inorganic molecules, on marine infrastructure such as pylons, boats, or pipes due to exposure to their environment. As fouling accumulates, it can have many adverse effects, including increasing drag, reducing the maximum speed of a ship and increasing fuel consumption, weakening supports on oil rigs and reducing the functionality of many sensors. In this review, the history and recent progress of techniques and strategies that are employed to inhibit fouling are highlighted, including traditional biocide antifouling systems, biomimicry, micro-texture and natural components systems, superhydrophobic, hydrophilic or amphiphilic systems, hybrid systems and active cleaning systems. This review highlights important considerations, such as accounting for the effects that antifouling strategies have on the sensing mechanism employed by the sensors. Additionally, due to the specialised requirements of many sensors, often a bespoke and tailored solution is preferential to general coatings or paints. A description of how both fouling and antifouling techniques affect maritime sensors, specifically acoustic sensors, is given.

Anti-pathogenic activity of graphene nanomaterials: A review

Graphene and its derivatives are promising candidates for a variety of biological applications, among which, their anti-pathogenic properties are highly attractive due to the outstanding physicochemical characteristics of these novel nanomaterials. The antibacterial, antiviral and antifungal performances of graphene are increasingly becoming more important due to the pathogen's resistance to existing drugs. Despite this, the factors influencing the antibacterial activity of graphene nanomaterials, and consequently, the mechanisms involved are still controversial. This review aims to systematically summarize the literature, discussing various factors that affect the antibacterial performance of graphene materials, including the shape, size, functional group and the electrical conductivity of graphene flakes, as well as the concentration, contact time and the pH value of the graphene suspensions used in related microbial tests. We discuss the possible surface and edge interactions between bacterial cells and graphene nanomaterials, which cause antibacterial effects such as membrane/oxidative/photothermal stresses, charge transfer, entrapment and self-killing phenomena. This article reviews the anti-pathogenic activity of graphene nanomaterials, comprising their antibacterial, antiviral, antifungal and biofilm-forming performance, with an emphasis on the antibacterial mechanisms involved.

Recently Emerging Nanotechnological Advancements in Polymer Nanocomposite Coatings for Anti-corrosion, Anti-fouling and Self-healing

Recent nanotechnological advancements have enabled novel innovations in protective polymer nanocomposites (PNC) coatings for anti-corrosion, anti-fouling and self-healing services on material surfaces. Nanotechnology encompases research, manufacturing, and application of nanoparticulate architectures, tubular structures, sheets or plates exhibiting sizes below 100 nanometers (nm) in at least a single dimension. Inclusions of nanoparticles into organic entities have demonstrated enhanced properties essential for attainiment of aesthetics, anti-corrosion, thermal stability for high-temperature performances, mechanical strength essential for resisting coating deterioration in harsh environments, nano-architectural cross-linking capable of hindering penetration of corrosive, and biofouling entities. Unlike previously published literature, this paper elucidates very recently emerging important advancements in novel techniques utilized in developing PNC coatings for applications in aerospace, packaging, automotive, biomedicine, maritime, and oil and gas industries for attaining superior anti-fouling, anti-corrosion, and self-healing behaviors on critical material surfaces. Emerging market structures and novel applications are also presented.

Strain variability in biofilm formation: A food safety and quality perspective

The inherent differences in microbial behavior among identically treated strains of the same microbial species, referred to as "strain variability", are regarded as an important source of variability in microbiological studies. Biofilms are defined as the structured multicellular communities with complex architecture that enable microorganisms to grow adhered to abiotic or living surfaces and constitute a fundamental aspect of microbial ecology. The research studies assessing the strain variability in biofilm formation are relatively few compared to the ones evaluating other aspects of microbial behavior such as virulence, growth and stress resistance. Among the available research data on intra-species variability in biofilm formation, compiled and discussed in the present review, most of them refer to foodborne pathogens as compared to spoilage microorganisms. Molecular and physiological aspects of biofilm formation potentially related to strain-specific responses, as well as information on the characterization and quantitative description of this type of biological variability are presented and discussed. Despite the considerable amount of available information on the strain variability in biofilm formation, there are certain data gaps and still-existing challenges that future research should cover and address. Current and future advances in systems biology and omics technologies are expected to aid significantly in the explanation of phenotypic strain variability, including biofilm formation variability, allowing for its integration in microbiological risk assessment.

Fouling-release and chemical activity effects of a siloxane-based material on tunicates

The antifouling performance of a siloxane-based elastomeric impression material (EIM) was compared to that of two silicone fouling-release coatings, Intersleek 757 and RTV-11. In field immersion trials, the EIM caused the greatest reduction in fouling by the solitary tunicate Ciona intestinalis and caused the longest delay in the progression of fouling by two species of colonial tunicate. However, in pseudobarnacle adhesion tests, the EIM had higher attachment strengths. Further laboratory analyses showed that the EIM leached alkylphenol ethoxylates (APEs) that were toxic to C. intestinalis larvae. The EIM thus showed the longest duration of chemical activity measured to date for a siloxane-based coating (4 months), supporting investigations of fouling-release coatings that release targeted biocides. However, due to potential widespread effects of APEs, the current EIM formulation should not be considered as an environmentally-safe antifoulant. Thus, the data also emphasize consideration of both immediate and long-term effects of potentially toxic constituents released from fouling-release coatings.

Superhydrophobic surfaces for applications in seawater

OBJECTIVE

Technological fields in which seawater is implied are numerorus, working in seawater (shipping, oil industry, marine aquaculture,..), and exploiting seawater in plants (cooling heat-exchange, desalination, power plants,..). All suffer from detrimental effects induced by biofouling mainly enhancing material failures and limiting energetic efficiencies. Among the remediation solutions, technologies coniugating economical, green and efficiency criteria should represent the direction. With the aim to meet these criteria, superhydrophobic (SH) technology attracted many researches for the protection of materials operating in contact with seawater.

METHOD

In this work, the literature focusing on such technology for the protection of surfaces in contact with seawater has been reviewed, mainly focusing on boat and ship hull protection.

RESULTS

Despite the growing interest around SH technology in seawater for fouling control and friction drag reduction of hulls, to date literature shows that superhydrophobicity in seawater is still limited if compared with a time window compatible with technological needs (set on years). An evaluation of the causes of early superhydrophobicity loss under operative conditions clearly indicates that, to the best of present knowledge, a SH surface cannot preserve this feature by itself alone (especially in real seawater). Hence, we have considered to highlight the behaviour of SH surfaces in seawater in relation to early stages of biocolonization (conditioning film and pioneering bioslime formation). Considering the annual costs sustained for the biofouling impact control, advantages coming from SH surfaces, in terms of foul control and friction drag reduction, would allow economical savings allowing to cover both the appliance of longevity keeping strategies of the SH surfaces and investments in green technologies of SH coating life cycle (production, storing). In addition a brief outlook is provided on technological fields exploiting seawater in pipelines (power and desalination plants), where the SH surface finishing finds potentially interesting application for fouling and corrosion prevention applications.

Proteomics dedicated to biofilmology: What have we learned from a decade of research?

Advances in proteomics techniques over the past decade, closely integrated with genomic and physicochemical approach, have played a great role in developing knowledge of the biofilm lifestyle of bacteria. Despite bacterial proteome versatility, many studies have demonstrated the ability of proteomics approaches to elucidating the biofilm phenotype. Though these investigations have been largely used for biofilm studies in the last decades, they represent, however, a very low percentage of proteomics works performed up to now. Such approaches have offered new targets for combating microbial biofilms by providing a comprehensive quantitative and qualitative overview of their protein cell content. Herein, we summarized the state of the art in knowledge about biofilm physiology after one decade of proteomic analysis. In a second part, we highlighted missing research tracks for the next decade, emphasizing the emergence of posttranslational modifications in proteomic studies stemming from recent advances in mass spectrometry-based proteomics.