Evaluation of UDMA's potential as a substitute for Bis-GMA in orthodontic adhesives

Methacrylic acid/Tween 80 engineered amorphous calcium phosphate as an effective bioactive reinforcing nanofillers in dental adhesive

Bioactive fillers in dental adhesives are designed to release beneficial ions, such as calcium and phosphate, to help in remineralization process, and preventing secondary caries. Their incorporation also aims to improve the longevity of dental restorations. Herein, CaP nanoparticles were synthesized through a water-in-oil emulsion method using Tween80 as a surfactant and methacrylic acid (MAA). MAA officiated as a co-surfactant and reduced the size of CaP nanoparticle, including improved compatibility with the components of dental adhesive. The incorporation of 2% T80/CaP/MAA nanofillers into dental adhesive demonstrated increased efficiency, as evidenced by a higher degree of conversion (%DC) and greater micro-tensile bond strength (μTBS). More importantly, T80/CaP/MAA nanofillers were able to induce remineralization process in the dental structure, which was confirmed by EDX mapping and IR imaging. Finally, a cytotoxicity assessment of the dental adhesive containing T80/CaP/MAA showed no significant adverse effects on human fibroblast cells.

Monomer elution and shrinkage stress analysis of addition-fragmentation chain-transfer-modified resin composites in relation to the curing protocol

OBJECTIVE

The purpose was to compare the effects of rapid (3 s) and conventional (20 s) polymerization protocols (PP) of mono- and multichip LED curing units (LCU) on shrinkage stress (SS) and monomer elution (ME) in bulk-fill resin-based composites (RBC) with and without addition-fragmentation chain-transfer (AFCT) monomer.

METHODS

Cylindrical (5x4mm) specimens were prepared from two RBCs containing different AFCT monomers (Filtek OneBulk-FOB; Tetric PowerFill-TPF) and one without (Tetric EvoCeram Bulk-TEC). After soaking for 3, 10, and 14 days (75 % ethanol), ME was quantified using standard monomers by High-Performance Liquid Chromatography. SS was measured from the start of polymerization to 5 min using a Materials Testing Machine. The radiant exitance of LCUs was measured using a spectrophotometer. ANOVA and Tukey's post-hoc test, multivariate analysis and partial eta-squared statistics were used to analyze the data (p < 0.05).

RESULTS

AFCT-modification significantly decreased ME (p < 0.001). ME was reduced by half by day 10 and by one tenth by the end of the 14-day compared to the 3-day sampling. ME itself was dependent, whereas the percentage of monomers released was independent of the PP used (p > 0.05). FOB showed the lowest SS (p < 0.001), while there was no significant difference between TPF and TEC (p = 0.124). Both ME and SS were significantly influenced by material type and PP.

SIGNIFICANCE

The incorporation of the AFCT monomer reduced ME, but this was inversely related to a decrease in exposure time. SS values reduced by rapid PP in parallel with increasing ME values. The utilization of the AFCT molecule in conjunction with an appropriate resin-, initiator-system is of significant consequence for the kinetics of polymerization and the incorporation of monomers into the network.

Micromechanical modelling for bending behaviour of novel bioinspired alumina-based dental composites

The clinical failure mode of dental crown ceramics involves radial cracking at the interface, driven by the surface tension generated from the flexure of the ceramic layer on the subsurface. This results in a reduced lifespan for most all-ceramic dental crowns. Therefore, investigating optimal material combinations to reduce stress concentration in dental crown materials has become crucial for future successful clinical applications. The anisotropic complex structures of natural materials, such as nacre, could potentially create suitable strong and damage-resistant materials. Their imitation of natural structural optimisation and mechanical functionality at both the macro- and micro-levels minimises weaknesses in dental crowns. This research aims to optimise cost-effective, freeze-casted bioinspired composites for the manufacture of novel, strong, and tough ceramic-based dental crowns. To this end, multilayer alumina (Al2O3) composites with four different polymer phases were tested to evaluate their bending behaviour and determine their flexural strength. A computational model was developed and validated against the experimental results. This model includes Al2O3 layers that undergo gentle compression and distribute stress, while the polymer layers act as stress relievers, undergoing plastic deformation to reduce stress concentration. Based on the experimental data and numerical modelling, it was concluded that these composites exhibit variability in mechanical properties, primarily due to differences in microstructures and their flexural strength. Furthermore, the findings suggest that bioinspired Al2O3-based composites demonstrate promising deformation and strengthening behaviour, indicating potential for application in the dental field.

Evaluation of the toxic potential of Bisphenol-A glycidylmethacrylate (BisGMA) on the third instar larvae of transgenic Drosophila

Introduction

In the present study the cytotoxic and genotoxic effects of Bisphenol-A glycidyl methacrylate (BisGMA) was studied on the third instar larvae of transgenic Drosophila melanogaster (hsp70-lacZ)Bg9.

Materials and methods

The concentration of BisGMA i.e. 0.005, 0.010, 0.015 and 0.020 M were established in diet and the larvae were allowed to feed on it for 24 h.

Results

A dose dependent significant increase in the activity of β-galactosidase was observed compared to control. A significant dose dependent tissue damage was observed in the larvae exposed to 0.010, 0.015 and 0.020 M of BisGMA compared to control. A dose dependent significant increase in the Oxidative stress markers was observed compared to control. BisGMA also exhibit significant DNA damaged in the third instar larvae of transgenic D. melanogaster (hsp70-lacZ)Bg9 at the doses of 0.010, 0.015 and 0.020 M compared to control.

Conclusion

BisGMA at 0.010, 0.015 and 0.020 M was found to be cytotoxic for the third instar larvae of transgenic D. melanogaster (hsp70-lacZ) Bg9.

Novel antibacterial low-shrinkage-stress resin-based cement

OBJECTIVE

A low-shrinkage-stress resin-based cement with antibacterial properties could be beneficial to create a cement with lower stress at the tooth-restoration interface, which could help to enhance the longevity of the fixed dental restoration by reducing microleakage and recurrent caries. To date, there has been no report on the development of a low-shrinkage-stress and bio-interactive cement. Therefore, the objectives of this study were to develop a novel low-shrinkage-stress resin-based cement containing dimethylaminohexadecyl methacrylate (DMAHDM) and investigate the mechanical and antibacterial properties for the first time.

METHODS

The monomers urethane dimethacrylate (UDMA) and triethylene glycol divinylbenzyl ether (TEG-DVBE) were combined and denoted as UV resin. Three cements were fabricated: (1) UV+ 0%DMAHDM (experimental control); (2) UV+ 3%DMAHDM, (3) UV+ %5DMAHDM. RelyX Ultimate cement was used as commercial control. Mechanical properties and Streptococcus mutans (S. mutans) biofilms growth on cement were evaluated.

RESULTS

The novel bio-interactive cement demonstrated excellent antibacterial and mechanical properties. Compared to commercial and experimental controls, adding DMAHDM into the UV cement significantly reduced colony forming unit (CFU) counts by approximately 7 orders of magnitude, metabolic activities from 0.29 ± 0.03 A₅₄₀/cm² to 0.01 ± 0.01 A₅₄₀/cm², and lactic acid production from 22.3 ± 0.74 mmol/L to 1.2 ± 0.27 mmol/L (n = 6) (p < 0.05). The low-shrinkage-stress cement demonstrated a high degree of conversion of around 70 %, while reducing the shrinkage stress by approximately 60%, compared to a commercial control (p < 0.05).

CONCLUSIONS

The new antibacterial low-shrinkage-stress resin-based cement provides strong antibacterial action and maintains excellent mechanical properties with reduced polymerization shrinkage stress.

CLINICAL SIGNIFICANCE

A low-shrinkage-stress resin-based cement containing DMAHDM was developed with potent antibacterial effects and promising mechanical properties. This cement may potentially enhance the longevity of fixed dental restoration such as a dental crown, inlay, onlay, and veneers through its excellent mechanical properties, low shrinkage stress, and strong antibacterial properties.

Meta-analytical analysis on components released from resin-based dental materials

OBJECTIVES

Resin-based materials are applied in every branch of dentistry. Due to their tendency to release substances in the oral environment, doubts have been raised about their actual safety. This review aims to provide a comprehensive analysis of the last decade literature regarding the concentrations of elutable substances released from dental resin-based materials in different type of solvents.

MATERIALS AND METHODS

All the literature published on dental journals between January 2010 and April 2022 was searched using international databases (PubMed, Scopus, Web of Science). Due to strict inclusion criteria, only 23 papers out of 877 were considered eligible. The concentration of eluted substances related to surface and volume of the sample was analyzed, considering data at 24 h as a reference. The total cumulative release was examined as well.

RESULTS

The most eluted substances were HEMA, TEGDMA, and BPA, while the less eluted were Bis-GMA and UDMA. Organic solvents caused significantly higher release of substances than water-based ones. A statistically significant inverse correlation between the release of molecules and their molecular mass was observed. A statistically significant positive correlation between the amount of released molecule and the specimen surface area was detected, as well as a weak positive correlation between the release and the specimen volume.

CONCLUSIONS

Type of solvent, molecular mass of eluates, and specimen surface and volume affect substances release from materials.

CLINICAL RELEVANCE

It could be advisable to rely on materials based on monomers with a reduced elution tendency for clinical procedures.

In Vitro Evaluation of Structural Factors Favouring Bacterial Adhesion on Orthodontic Adhesive Resins

Bacterial adhesion to the surface of orthodontic materials is an important step in the formation and proliferation of plaque bacteria, which is responsible for enamel demineralization and periodontium pathologies. With the intent of investigating if adhesive resins used for bracket bonding are prone to bacteria colonization, the surface roughness of these materials has been analyzed, combining information with a novel methodology to observe the internal structures of orthodontic composites. Scanning electron microscopy, combined with focus ion bean micromachining and stylus profilometry analyses, were performed to evaluate the compositional factors that can influence specific pivotal properties facilitating the adhesion of bacteria to the surface, such as surface roughness and robustness of three orthodontic adhesive composite resins. To confirm these findings, contact angle measurements and bacteria incubation on resin slide have been performed, evaluating similarities and differences in the final achievement. In particular, the morphological features that determine an increase in the resins surface wettability and influence the bacterial adhesion are the subject of speculation. Finally, the focused ion beam technique has been proposed as a valuable tool to combine information coming from surface roughness with specific the internal structures of the polymers.

Low-shrinkage-stress nanocomposite: An insight into shrinkage stress, antibacterial, and ion release properties

The aims are: (a) To develop the first low-shrinkage-stress nanocomposite with antibacterial and remineralization capabilities through the incorporation of dimethylaminododecyl methacrylate (DMAHDM) and nanoparticles of amorphous calcium phosphate (NACP); (b) to investigate the effects of the new composite on biofilm inhibition, mechanical properties, shrinkage stress, and calcium (Ca) and phosphate (P) ion releases. The low-shrinkage-stress resin consisted of urethane dimethacrylate and triethylene glycol divinylbenzyl ether. Composite was formulated with 3% DMAHDM and 20% NACP. Mechanical properties, shrinkage stress, and degree of conversion were evaluated. Streptococcus mutans biofilm growth on composites was assessed. Ca and P ion releases were measured. The shrinkage stress of the low-shrinkage-stress composite containing 3% DMAHDM and 20% NACP was 36% lower than that of traditional composite control (p < 0.05), with similar degrees of conversion of 73.9%. The new composite decreased the biofilm colony-forming unit by 4 log orders and substantially reduced biofilm lactic acid production compared to control composite (p < 0.05). Incorporating DMAHDM to the low-shrinkage-stress composite did not adversely affect the Ca and P ion release. A novel bioactive nanocomposite was developed with low shrinkage stress, strong antibiofilm activity, and high levels of ion release for remineralization, without undermining the mechanical properties and degree of conversion.

Bioactive low-shrinkage-stress nanocomposite suppresses S. mutans biofilm and preserves tooth dentin hardness

Recurrent dental caries is one of the main reasons for resin composite restoration failures. This study aimed to: (1) develop a bioactive, low-shrinkage-stress, antibacterial and remineralizing composite and evaluate the sustainability of its antibacterial effect against Streptococcus mutans (S. mutans) biofilms; and (2) evaluate the remineralization and cariostatic potential of the composite containing nanoparticles of amorphous calcium phosphate (NACP) and dimethylaminohexadecyl methacrylate (DMAHDM), using dentin hardness measurement and a biofilm-induced recurrent caries model. The antibacterial and remineralizing low-shrinkage-stress composite consisted of urethane dimethacrylate (UDMA) and triethylene glycol divinylbenzyl ether (TEG-DVBE), 3% DMAHDM and 20% NACP. S. mutans biofilm was used to evaluate antibiofilm activity, before and after 3 months of composite aging in acidic solution. Human dentin was used to develop a recurrent caries biofilm-model. Adding DMAHDM and NACP into low shrinkage-stress composite did not compromise the flexural strength. The low-shrinkage-stress composite with DMAHDM achieved substantial reductions in biofilm colony-forming units (CFU), lactic acid production, and biofilm biomass (p < 0.05). The low-shrinkage-stress DMAHDM+NACP composite exhibited no significant difference in antibacterial performance before and after 3 months of aging, demonstrating long-term antibacterial activity. Under S. mutans biofilm acidic attack, dentin hardness (GPa) was 0.24 ± 0.04 for commercial control, and 0.23 ± 0.03 for experimental control, but significantly higher at 0.34 ± 0.03 for DMAHDM+NACP group (p < 0.05). At an instrumental compliance of 0.33 μm/N, the polymerization shrinkage stress of the new composite was 36% lower than that of a traditional composite (p < 0.05). The triple strategy of antibacterial, remineralization and lower shrinkage-stress has great potential to inhibit recurrent caries and increase restoration longevity. Statement of Significance Polymerization shrinkage stress, masticatory load over time as well as biochemical degradation can lead to marginal failure and secondary caries. The present study developed a new low-shrinkage-stress, antibacterial and remineralizing dental nanocomposite. Polymerization shrinkage stress was greatly reduced, biofilm acid production was inhibited, and tooth dentin mineral and hardness were preserved. The antibacterial composite possessed a long-lasting antibiofilm effect against cariogenic bacteria S. mutans. The new bioactive nanocomposite has the potential to suppress recurrent caries at the restoration margins, protects tooth structures, and increases restoration longevity.

Chemistry of novel and contemporary resin-based dental adhesives

The chemistry of resin-based dental adhesives is critical for its interaction with dental tissues and long-term bonding stability. Changes in dental adhesives composition influences the materials' key physical-chemical properties, such as rate and degree of conversion, water sorption, solubility, flexural strength and modulus, and cohesive strength and improves the biocompatibility to dental tissues. Maintaining a suitable reactivity between photoinitiators and monomers is important for optimal properties of adhesive systems, in order to enable adequate polymerisation and improved chemical, physical and biological properties. The aim of this article is to review the current state-of-the-art of dental adhesives, and their chemical composition and characteristics that influences the polymerisation reaction and subsequent materials properties and performance.

Flexural strength and surface microhardness of materials used for temporary dental disocclusion submitted to thermal cycling: An in vitro study

OBJECTIVE

The objective of this study was to evaluate the effect of temperature variation on surface microhardness and resistance to flexion of different materials used for making a temporary dental disocclusion.

METHODS

One hundred specimens were made of the following materials (n=20): glass ionomer cement (GIC); compomer (CP); composite resin (CR); Blue colour resin composite for temporary dental disocclusion (BTDD); ultraviolet colour resin composite for temporary dental disocclusion (UVTDD). They were stored in distilled water for 24hours and, subsequently, half of the specimens in each group were subjected to thermal cycling (n=10). All samples were subjected to the microhardness test (HMV-2000) and the flexural strength analysis (INSTRON). The data were submitted to parametric statistical analysis (ANOVA) and Tukey's complementary test with a significance level of 5%. In the mechanical tests, all materials except the GIC showed a statistically significant difference between the groups subjected to thermal cycling and not submitted, and thermal cycling (P<0.05) was responsible for the reduction of the values found, except for GIC.

RESULTS

In the mechanical tests, all materials except the GIC showed a statistically significant difference between the groups subjected to thermal cycling and not submitted, and thermal cycling (P<0.05) was responsible for the reduction of the values found, except for GIC. For microhardness, the highest average was found for BTDD and UVTDD (P≤0.05). As for the resistance, the flexion was found that in the groups not submitted to thermal cycling there was no statistically significant difference for all materials, except for GIC, for the groups with thermal cycling the materials BTDD and UVTDD showed a statistically significant difference from GIC, however, they did not differ statistically from the CP and CR groups.

CONCLUSION

BTDD and UVTDD presented higher average results of surface microhardness and, in the resistance test, the flexion of these materials behaved similarly to the CP and the CR studied. The temperature variation has an effect on the properties of these materials.

High-Performance Dental Adhesives Containing an Ether-Based Monomer

Dental adhesives are vital for the success of dental restorations. The objective of this study is to make strong and durable dental adhesives that are free from 2 symbolic methacrylate-based dental resins-2-bis[4-(2-hydroxy-3-methacryl-oxypropoxy)-phenyl]-propane (Bis-GMA) and 2-hydroxyethyl-methacrylate (HEMA)-and have equivalent/improved bonding strength and durability. We formulated, prepared, and evaluated 2 dental adhesives using mixtures of a hydrolytically stable ether-based monomer, triethylene glycol divinylbenzyl ether (TEG-DVBE), with urethane dimethacrylate (UDMA) or pyromellitic glycerol dimethacrylate. These adhesives were composed of equimolar ester-/ether-based vinyl functional groups. They were compared with Bis-GMA/HEMA-based commercial and experimental dental adhesives in terms of shear bond strength and microtensile bond strength (µTBS) to human dentin and the µTBS bond stability under extended thermocycling challenges. In addition, the resins' infiltration to dentin tubules, mechanical performance, and chemical properties were assessed by scanning electron microscopy, ISO standard flexural strength and modulus measurements, contact angle measurements, and water sorption/solubility measurements. The hybrid TEG-DVBE-containing dental adhesives generated equivalent shear bond strength and µTBS in comparison with the controls. Significantly, these adhesives outperformed the controls after being challenged by 10,000 thermocycles between 5 °C and 55 °C. Water contact angle measurements suggested that the hybrid dental adhesives were relatively more hydrophobic than the Bis-GMA/HEMA controls. However, both TEG-DVBE-containing adhesives developed more and deeper resin tags in dentin tubules and formed thicker hybrid layers at the composite-dentin interface. Furthermore, the water solubility of UDMA/TEG-DVBE resins was reduced approximately 89% in comparison with the Bis-GMA/HEMA controls. The relatively hydrophobic adhesives that achieved equivalent/enhanced bonding performance suggest great potentials in developing dental restoration with extended service life. Furthermore, the TEG-DVBE-containing materials may find wider dental applications and broader utility in medical device development.

Solvent and HEMA Increase Adhesive Toxicity and Cytokine Release from Dental Pulp Cells

The aim of the present study was to evaluate the effect of the hydroxyethyl-methacrylate (HEMA) concentration and solvent content of dental adhesives on cell viability and cytokine (IL-1b, IL-6, IL-10, TNF-α) release by human dental pulp cells (HDPCs). HDPCs were obtained from fresh extracted human third molars. Experimental adhesives were prepared containing different concentrations of HEMA (0%, 10%, and 20%) with and without solvent (ethanol 10%). Cylindrical specimens were immersed on culture medium during 24 h to obtain the extracts. The cells were incubated with extracts (culture medium + components leached from the adhesives) of different adhesives, and cell viability and cytokine release were evaluated after 6 and 24 h of exposure. Adhesives containing HEMA promoted high cell viability reduction after 6 h of exposure; but after 24 h, the results were similar to the ones found among control group cells. These effects on cell viability were prominently increased with the addition of solvent. Although IL-1b release was not affected by exposure to eluates, other cytokines (IL-10, IL-6, TNF-α) were modulated by the different experiment conditions, directly influenced by the HEMA concentration and presence of solvent. Higher HEMA concentrations, combined with the presence of solvent, can promote significant reduction on HDPC viability, increasing the release of anti- and pro-inflammatory mediators.

Preparation of low shrinkage stress Bis-GMA free dental resin composites with a synthesized urethane dimethacrylate monomer

A new urethane dimethacrylate TMA was synthesized through a typical urethane reaction. TMA was used to replace 1,6-bis(methacryloxy-2-ethoxycarbonyl- amino)-2,4,4- trimethylhexane (UDMA) in UDMA based composite partially or totally to prepare TMA containing composites. Critical properties of TMA containing composites were investigated. 2,2-bis[4(2-hydroxy-3-methacryloy- propyloy)phenyl]propane (Bis-GMA) based and UDMA based composites were used as references. FT-IR and ¹H-NMR confirmed the structure of TMA. All of experimental dental resin composites had the similar double bond conversion (p > 0.05). With a certain amount of TMA, TMA containing composites could have lower volumetric shrinkage (p < 0.05) and shrinkage stress (p < 0.05) than control groups. Water sorption, solubility, flexural strength and modulus of TMA containing composites were not worse than those of control groups. All of TMA containing composites and UDMA based composite had the same fracture toughness (p > 0.05), which was higher than that of Bis-GMA based composite (p < 0.05). TMA has potential as Bis-GMA substitute to prepare Bis-GMA free dental resin composites with low shrinkage stress.

Association between polymorphisms in genes encoding estrogen receptors (ESR1 and ESR2) and excreted bisphenol A levels after orthodontic bracket bonding: a preliminary study

Background

Bisphenol A (BPA) is released from orthodontic composites used for bracket bonding. Genetic variations could modify the metabolism of this chemical within the organism. Considering that free BPA binds to estrogen receptors causing harmful effects to health, the present in vivo study aimed to evaluate the association between genetic polymorphisms in genes encoding estrogen receptors (ESR1 and ESR2) and excreted BPA levels in orthodontic patients.

Methods

Quantification of BPA levels in the urine of 16 patients was performed in a gas chromatograph mass spectrometer before (T0), at 24 h (T1), and 1 week (T2) after bracket bonding. DNA was extracted from saliva, and one genetic polymorphism in ESR1 (rs2234693) and two in ESR2 (rs4986938 and rs1256049) were analyzed by real-time PCR. Increases in BPA levels in the urine at T1 and T2 were grouped according to the genotype, and mean differences were compared by unpaired T test or Mann-Whitney test according to the normality of the data. The established alpha was 5%.

Results

BPA levels increased significantly at T1 and T2. There were no statistically significant differences in the increases in BPA levels according to the genotype for any genetic polymorphism (P > 0.05), at neither 24 h nor 1 week after bracket bonding.

Conclusions

The results suggested that there are no association between excreted BPA levels after bracket bonding and the evaluated genetic polymorphisms in ESR1 and ESR2. Further research should be performed in order to confirm these results.

Adverse reactions to orthodontic materials

Adverse effects can arise from the clinical use of orthodontic materials, due to the release of constituent substances (ions from alloys and monomers, degradation by-products, and additives from polymers). Moreover, intraoral aging affects the biologic properties of materials. The aim of this review is to present the currently identified major adverse effects of the metallic and polymeric components found in orthodontic appliances and materials. Corrosion in metallic orthodontic attachments releases metal ions, mainly iron, chromium, and nickel. The latter has received the greatest attention because of its reported potential for an allergic response. The formation of an oxide layer may inhibit the outward movement of ions, thereby acting as an obstacle for release. Titanium alloys have superior corrosion resistance than stainless steel. The efficiency of polymerisation is considered an essential property for all polymers. A poor polymer network is susceptible to the release of biologically reactive substances, such as bisphenol-A (BPA), which is capable of inducing hormone-related effects. The close proximity of a light-curing tip to the adhesive, pumice prophylaxis after bonding, indirect irradiation and mouth rinsing during the first hour after bonding may decrease BPA release. The adverse effects of some orthodontic materials should be considered during material selection and throughout orthodontic treatment, in order to minimise possible undesirable implications.

Bisphenol A release from orthodontic adhesives measured in vitro and in vivo with gas chromatography

INTRODUCTION

The objectives of this study were to quantify in vitro the Bisphenol A (BPA) release from 5 orthodontic composites and to assess in vivo the BPA level in patients' saliva and urine after bracket bonding with an orthodontic adhesive system.

METHODS

For the in-vitro portion of this study, 5 orthodontic composites were evaluated: Eagle Spectrum (American Orthodontics, Sheboygan, Wis), Enlight (Ormco, Orange, Calif), Light Bond (Reliance Orthodontic Products, Itasca, Ill), Mono Lok II (Rocky Mountain Orthodontics, Denver, Colo), and Transbond XT (3M Unitek, Monrovia, Calif). Simulating intraoral conditions, the specimens were immersed in a water/ethanol solution, and the BPA (ng.g^-1) liberation was measured after 30 minutes, 24 hours, 1 day, 1 week, and 1 month by the gas chromatography system coupled with mass spectrometry. Twenty patients indicated for fixed orthodontic treatment participated in the in-vivo study. Saliva samples were collected before bracket bonding and then 30 minutes, 24 hours, 1 day, 1 week, and 1 month after bonding the brackets. Urine samples were collected before bonding and then at 1 day, 1 week, and 1 month after bonding. The results were analyzed statistically using analysis of variance and Tukey posttest, with a significance level of 5%.

RESULTS

All composites evaluated in vitro released small amounts of BPA. Enlight composite showed the greatest release, at 1 month. Regarding the in-vivo study, the mean BPA level in saliva increased significantly only at 30 minutes after bonding in comparison with measurements recorded before bonding.

CONCLUSIONS

All orthodontic composites released BPA in vitro. Enlight and Light Bond had, respectively, the highest and lowest BPA releases in vitro. The in-vivo experiment showed that bracket bonding with the Transbond XT orthodontic adhesive system resulted in increased BPA levels in saliva and urine. The levels were significant but still lower than the reference dose for daily ingestion.

Release of monomers from orthodontic adhesives

INTRODUCTION

Most composite resins release both bisphenol A (BPA), which disrupts the endocrine balance, and triethylene glycol dimethacrylate (TEGDMA), which has high risks for human health: eg, allergies and cytotoxicity. The aim of this study was to characterize monomers released from orthodontic adhesives.

METHODS

We studied samples of orthodontic adhesives by associating 2 techniques: gas phase chromatography and mass spectrometry.

RESULTS

The in-vitro analysis detected significant quantities of BPA, TEGDMA, and other monomers in orthodontic adhesives used in daily practice: Transbond XT, Transbond Supreme LV (both, 3M Unitek, Monrovia, Calif), Blugloo (Ormco, Orange, Calif), and MonoLok 2 (Rocky Mountain Orthodontics, Denver, Colo).

CONCLUSIONS

Clinicians should consider that orthodontic adhesives contain BPA, an endocrine disruptor; TEGDMA, an allergic and a cytotoxic compound; and carcinogenic genotoxic compounds. These molecules are not mentioned in the material safety data sheets. Manufacturers should declare all components of dental composites to identify these substances that may result in allergic or undesirable side effects for patients and dental staff.

Preparation of a Bis-GMA-Free Dental Resin System with Synthesized Fluorinated Dimethacrylate Monomers

With the aim of reducing human exposure to Bisphenol A (BPA) derivatives in dentistry, a fluorinated dimethacrylate monomer was synthesized to replace 2,2-bis[4-(2-hydroxy-3-methacryloy-loxypropyl)-phenyl]propane (Bis-GMA) as the base monomer of dental resin. After mixing with reactive diluent triethyleneglycol dimethacrylate (TEGDMA), fluorinated dimethacrylate (FDMA)/TEGDMA was prepared and compared with Bis-GMA/TEGDMA in physicochemical properties, such as double bond conversion (DC), volumetric shrinkage (VS), water sorption (WS) and solubility (WSL), flexural strength (FS) and modulus (FM). The results showed that, when compared with Bis-GMA based resin, FDMA-based resin had several advantages, such as higher DC, lower VS, lower WS, and higher FS after water immersion. All of these revealed that FDMA had potential to be used as a substitute for Bis-GMA. Of course, many more studies, such as biocompatibility testing, should be undertaken to prove whether FDMA could be applied in clinic.

A composition-controlled cross-linking resin network through rapid visible-light photo-copolymerization

This work introduces a cross-linked resin network with controlled chemical composition, a clinically practical procedure to make it in situ, and appropriate analytical tools for chemical structure and kinetic studies.

Zero valent metal/RAFT agent mediated CRP of functional monomers at room temperature: a promising catalyst system for CRP

A facile approach to synthesize GMA polymers using Fe(0)/RAFT agent mediated control radical polymerization.

Do we need a randomized controlled trial to assess trivial, albeit standard used, clinical steps in bonding? The answer is yes, but there are some interpretation issues

The feasibility of generalizing and extrapolating the results of the RCT assessing the necessity of a bonding stage to the routine clinical situation is discussed in this commentary. The lack of difference in failure rate between the two procedures followed may not receive the dimensions of a directive to alter a step of the bonding process, before other factors related to the performance of the materials are considered.

Effect of intraoral aging on the setting status of resin composite and glass ionomer orthodontic adhesives

INTRODUCTION

The aim of this study was to assess the effect of intraoral aging on the setting status of a resin composite and a glass ionomer adhesive, relative to control specimens stored in water.

METHODS

Metallic brackets were bonded with resin composite orthodontic adhesive (Transbond XT; 3M Unitek, Monrovia, Calif) or a glass ionomer cement (Fuji I; GC, Tokyo, Japan) to recently extracted premolars and kept in water for 6 months. The same materials were also bonded to the premolars of orthodontic patients. After 6 months, the teeth were carefully extracted, with the brackets intact on their buccal surfaces. All teeth were embedded in epoxy resin and sectioned buccolingually. Fourier transform infrared microscopy and Raman microscopy were used for the estimation of the degree of cure in the composite and the salt yield in the glass ionomer adhesives.

RESULTS

The control samples of the composite showed significantly lower degrees of cure than did the retrieved specimens (52.40% ± 3.21% vs 57.62% ± 1.32% by Fourier transform infrared microscopy, and 61.40% ± 2.61% vs 67.40% ± 3.44% by Raman microscopy). Raman microscopy significantly overestimated the degree of cure and failed to provide reliable information for the salt yield in the glass ionomer cement. Fourier transform infrared microscopy showed increased, but no statistically significant difference in, aluminum-carboxylate salts in the retrieved specimens.

CONCLUSIONS

Enhanced oxidation of residual carbon-carbon bonds in the composite and slightly increased dissolution of the weaker calcium-salt phase in the glass ionomer cement were the main differences in the intraorally aged specimens in comparison with the specimens stored in water.

Preparation of low shrinkage methacrylate-based resin system without Bisphenol A structure by using a synthesized dendritic macromer (G-IEMA)

With the growing attention on estrogenic effect of Bisphenol A (BPA), the application of BPA derivatives like Bis-GMA in dental materials has also been doubted. In this research, new BPA free dental resin systems were prepared with synthesized dendritic macromer G-IEMA, UDMA, and TEGDMA. Physicochemical properties, such as double bond conversion, polymerization shrinkage, flexural strength and modulus, fracture energy, water sorption and solubility of BPA free resin formulations were investigated. Bis-GMA/TEGDMA resin system was used as a control. Results showed that the prepared BPA free resins could have higher double bond conversion, comparable or lower polymerization shrinkage and water sorption, and lower water solubility, when compared with Bis-GMA/TEGDMA resin. Though flexural strength and modulus of prepared BPA free polymers were lower than those of Bis-GMA/TEGDMA polymer, BPA free polymers had higher fracture energies and showed plastic deformation prior to fracture, all of these two phenomena showed that BPA free polymers in this research might have higher fracture toughness which would be good for the service life of dental materials.