Negative role of biochars in the dissipation and vegetable uptake of polycyclic aromatic hydrocarbons (PAHs) in an agricultural soil: Cautions for application of biochars to remediate PAHs-contaminated soil

Polycyclic aromatic hydrocarbons in intertidal surface sediments of mangrove wetlands in Dongzhai Harbor, Haikou, China: Understanding sources, distribution, and ecological risk

Polycyclic aromatic hydrocarbons (PAHs) can be stored for long periods in soil or sediments, especially in sediments containing large amounts of organic matter, because of their special properties. Due to the high organic matter content in mangrove forests, this area serve as natural reservoir or a "sink" for persistent organic pollution. For this reason, sediment and soil samples were obtained from the mangrove wetland in Dongzhai Harbor, Hainan, to examine the distribution of PAHs concentration, source, and ecological danger. The PAHs content varied from 69.94 to 1481.91 ng·g-1 and presented a mean of 244.44 ng·g-1. The maximum PAHs concentration of 1481.91 ng·g-1 occurred at station DZ-03 which located at the innermost of the harbor. The PAHs concentrations in the other stations ranged within 69.94-356.66 ng·g-1, and the average value was 131.95 ng·g-1, which denotes a medium to low pollution level. The diagnostic ratio approach and principal component analysis revealed that the primary source of PAHs was the combustion of coal and biomass. The majority of the PAHs at Station DZ-03 showed high potential danger according to the ecological risk assessment. At the other stations, Ace and BghiP pose danger while the potential risk of the other PAHs was low. TEQBaP revealed high concentrations at Station DZ-03 and low concentrations at the other stations, where the overall potential ecological risk was low. Nevertheless, PAHs emissions should still be given attention, and the burning of fossil fuels and biomass should be reduced to decrease the potential ecological risk.

Effect of freeze-thaw cycle aging on biochar application in DEHP contaminated Mollisols: Insights from soil properties and microbial community

Biochar holds significant promise for remediation of organic pollutants. However, the impact of biochar on di-(2-ethylhexyl) phthalate (DEHP)-contaminated Mollisols after freeze-thaw cycles is largely unknown, according to the seasonal traits observed at high latitudes. In this study, fresh biochar (BC) was produced from corn straw, and freeze-thaw aging biochar (FBC) was prepared by simulating winter temperatures in the Mollisol region of Northeast China using BC as a precursor. Pot experiments were conducted to evaluate the effects of freeze-thaw aging on the detoxification efficiency of biochar, the improvement of soil physical and chemical properties, and the regulation of soil microbial community structure and functional genes. The results indicated that biochar after freeze-thaw cycling significantly improved the physical and chemical properties of Mollisols compared with the control, reducing DEHP content by 99.08 % after 28 days. Metagenomic sequencing further revealed the presence of microorganisms and genetic elements potentially involved in DEHP degradation in the soil. The treatment group with freeze-thaw aging biochar exhibited higher microbial diversity and abundance, particularly in Proteobacteria, Bacteroides, and Firmicutes. Analysis of the DEHP degradation pathway via benzoic acid route revealed an increase in the abundance of degraded functional genes/enzymes (benC-xylZ, pacL, catB, pcaG, mhpE, and mhpF). The up-regulation of nitrogen fixation genes and nitrification genes (amoB, hao, narG, nifD, and vnfH) along with a 49.19 % increase in soil microbial biomass nitrogen suggested that freeze-thaw aging biochar benefited nitrogen cycling. Furthermore, the feasibility of applying biochar to high-latitude agricultural settings was validated using pakchoi (Brassica rapa L. ssp. chinensis) as a test crop. These findings suggest that the freeze-thaw aging process enhances the effectiveness of biochar in remediating DEHP-contaminated Mollisols. This study offers a novel perspective on the restoration and improvement of Mollisol productivity in high-latitude regions through biochar application.

Effects of nanoscale zero-valent iron loaded biochar on the fate of phenanthrene in soil-radish (Raphanus sativus L. var.radculus pers) system

Nanoscale zero-valent iron loaded on biochar (nZVI@BC) has been proven to be effective in activating persulfate to remediate soil organic pollutants. However, studies on subsequent plant growth and microbial community changes in remediated soil remain limited. In this study, nZVI@BC, nZVI, and nanoscale biochar (nBC) were ball-mill produced and applied as amendments in pot experiments with PAH-contaminated soil to investigate their impacts on soil-crop (radish, Raphanus sativus L.) systems, and the widely distributed phenanthrene (Phe) was selected as model pollutant. The results indicate that nZVI@BC could induce more (75%) Phe accumulation in radish compared to the control treatment, but did not result in significant differences in plant biomass or enzyme activity. In Phe non-contaminated treatments, the Fe content of radish shoots increased from 86.87 ± 5.61 mg/kg DW without material application to 125.20 ± 11.93 mg/kg DW with nZVI@BC, while no significant differences were observed in roots. nZVI@BC and nBC increased the non-desorbed fraction of PAHs with low bio-availability by 13.6% and 10.2%, respectively, after 45 days compared to the control treatment. Illumina MiSeq sequencing revealed that nZVI@BC did not adversely affect the richness and diversity of soil microbial communities. Instead, it promoted the enrichment of bacteria related to the degradation of organic pollutants, such as Lysobacter and Spingomonas. The findings suggest that nZVI@BC after chemical oxidation remediation might be harmful to subsequent plants and ecosystems but much better than nZVI alone. The amount of nZVI@BC should be accurately calculated before chemical oxidation remediation.

Insights into the Relationship between Temperature Variation and NAPL Removal during In Situ Thermal Remediation of Soil in the Presence of NAPL-Water Co-boiling: A Two-Dimensional Visualized Sandbox Study

Thermal remediation effectively treats sites contaminated with nonaqueous phase liquids (NAPL) by heating soil. A key process is the co-boiling at the water-NAPL interface, which lowers the boiling point due to combined vapor pressures, potentially reducing energy needs. However, determining the optimal end time for heating is challenging due to the invisible nature of underground NAPL, often resulting in excessive energy use. The initial NAPL pool size and distance from the heat source influence the spatiotemporal evolution of the NAPL-water interface, defining three zones: the co-boiling equilibrium zone, a nonequilibrium zone, and an unaffected zone. The temperature data collected by fixed temperature sensors can reflect the spatiotemporal evolution of these zones, offering valuable insights into NAPL removal. This study tackles these challenges using a two-dimensional visualized sandbox integrated with real-time image processing and an array of temperature sensors to monitor the NAPL removal and temperature variation. The results reveal semiquantitatively the impact of different initial NAPL amounts and spatial distributions on temperature variations. An optimized strategy is proposed for temperature sensor positioning, and a qualitative relationship is established between the temperature increase and NAPL removal. These findings can enhance our understanding of subsurface temperature dynamics, supporting more efficient, decarbonized remediation practices.

PAH Contamination, Sources and Health Risks in Black Soil Region of Jilin Province, China

Soils in the Black Soil Zone of northeast China are experiencing pollution from polycyclic aromatic hydrocarbons (PAHs) as the region undergoes urbanization. In this study, 119 topsoil samples were collected from the black soil agricultural area in Jilin Province, China to investigate the characteristics and spatial distribution of 16 PAHs. The total concentration of ∑16 PAHs in the agricultural soils ranged from 2.546 to 33.993 mg/kg, with a mean value of 9.99 mg/kg. Positive matrix factorization (PMF) analysis indicated that vehicle exhaust and oil combustion were identified as the main contributors to traffic- and energy-related pollution. The inherited lifetime carcinogenicity risk (ILCR) was found to be relatively low, indicating a low potential risk in this region, with adults (1.34 × 10-5) exhibiting a higher risk than adolescents (8.62 × 10-6) and children (7.49 × 10-6). The highest values for intake, skin contact, and inhalation routes were observed in the adult group, suggesting that adult residents in certain areas may be at increased health risk. This study enhances our understanding of the pathways through which PAHs enter agricultural soils in Jilin Province and provides insights that could aid in addressing PAH pollution in black soil, ultimately contributing to more sustainable agricultural practices in the region.

Occurrence status, source analysis and risk assessment of polycyclic aromatic hydrocarbons in intertidal surface sediments of typical mangrove wetlands in Guangxi Province, China

This study investigated the occurrence status, sources, and risk assessment of polycyclic aromatic hydrocarbons (PAHs) in sediments from three typical mangrove areas in Guangxi Province, China. Results showed that the PAH content in the three studied regions ranged from 39.76 ng·g-1 to 164.93 ng·g-1, and the average concentration was 92.87 ng·g-1. The PAHs that were detected were mainly 3-ring and 4-ring. The source of PAHs, as traced by the diagnostic ratio method and principal component analysis, was mainly from combustion. The toxicity risk assessment showed that the content of all PAHs was lower than the Effects Range Low (ERL), and the potential ecological risk was low. The toxicity equivalent (TEQBaP) content ranged from 4.75 ng·g-1 to 19.20 ng·g-1, with an average of 12.08 ng·g-1. Overall, the ecological risk of PAHs in mangrove sediments in Guangxi is considered low.

Uptake of polycyclic aromatic hydrocarbons (PAHs) from PAH-contaminated soils to carrots and Chinese cabbages under the greenhouse and field conditions

Polycyclic aromatic hydrocarbons (PAHs) with the properties of structural stability, semi-volatility, and hydrophobicity are toxic and persistent in environments; thus, their transport and fate in agroecosystems is essential for reducing PAH accumulation in the edible parts of crops. Here, we cultivated cabbages (Brassica pekinensis L.) and carrots (Daucus carota L.) in PAH-contaminated soils under the greenhouse and field conditions. After harvesting, we observed a 9.5-46% reduction in soil ∑PAH concentrations. There were 37% of bioconcentration factors (BCFbs) > 1 and 93% of translocation factors (TFab) > 1, while low-molecular-weight (LMW) PAHs had higher BCFbs than high-molecular-weight (HMW) PAHs. The PAH concentrations showed significant and positive correlations among soils, the belowground parts, and the aboveground parts. The toxicity equivalent concentration (TEQBaP) followed the order of cabbage (greenhouse) > cabbage (field) > carrot (greenhouse) > carrot (field), suggesting potentially higher health risks in cabbage relative to carrot and vegetables under the greenhouse relative to field condition. Our study suggested growing carrots under field conditions as a management strategy for reducing the risks of vegetables grown in PAH-contaminated soils.

Degradation and mechanism of PAHs by Fe-based activated persulfate: Effect of temperature and noble metal

The accumulation of contaminants like PAHs in soil due to industrialization, urbanization, and intensified agriculture poses environmental challenges, owing to their persistence, hydrophobic nature, and toxicity. Thus, the degradation of PAHs has attracted worldwide attention in soil remediation. This study explored the effect of noble metal and temperature on the degradation of various polycyclic aromatic hydrocarbons (PAHs) in soil, as well as the types of reactive radicals generated and mechanism. The Fe-Pd/AC and Fe-Pt/AC activated persulfate exhibited high removal efficiency of 19 kinds of PAHs, about 79.95 % and 83.36 %, respectively. Fe-Pt/AC-activated persulfate exhibits superior degradation efficiency than that on Fe-Pd/AC-activated persulfate, due to the higher specific surface area and dispersity of Pt particles, thereby resulting in increased reactive radicals (·OH, SO4-· and ·OOH). Additionally, thermal activation enhances the degradation of PAHs, with initial efficiencies of 64.20 % and 55.49 % on Fe-Pd/AC- and Fe-Pt/AC-activated persulfate systems respectively, increasing to 76.05 % and 73.14 % with elevated temperatures from 21.5 to 50 °C. Metal and thermal activation facilitate S2O82- activation, generating reactive radicals, crucial for the degradation of PAHs via ring opening and oxygen hydrogenation reactions, yielding low-ring oxygen-containing derivatives such as organic acids, keto compounds, ethers, and esters. Furthermore, understanding the impact of parameters such as activation temperature and the types of noble metals on the degradation of PAHs within the activated persulfate system provides a theoretical foundation for the remediation of PAH-contaminated soil.

Submerged plant-biochar composite system exhibits effective control over residual organic pollutants in the benthic organisms of aquaculture ponds

As of now, submerged plants and biochar have demonstrated significant benefits in aquaculture pond sediment remediation. However, there is limited research on the synergistic effects of biochar and submerged plants in mitigating hydrophobic organic contaminant (HOC) accumulation in aquaculture benthic organisms and in controlling the nutrient (nitrogen and phosphorus) levels in aquaculture water. This study assesses a submerged plant-biochar system's efficacy in removing HOCs from simulated freshwater aquaculture ponds. Vallisneria natans was planted in sediment with varying levels of wheat straw biochar, while Corbicula fluminea served as the targeted benthic organism. The bioaccumulation experiment identified the optimal biochar ratio for the Vallisneria natans-biochar system in controlling HOCs in aquaculture products. Analyses included final accumulation concentrations in benthic organisms, changes in freely-dissolved concentrations in aquaculture sediment, and a mass balance calculation to explore key factors in their removal from the system. Results indicated that the Vallisneria natans-1.5% biochar composite system achieved optimal control of HOCs in sediment and aquaculture products. Biochar addition to the sediment in the composite system demonstrated a "promotion with low addition, inhibition with high addition" effect on Vallisneria natans growth. Notably, the addition of 1.5% biochar (VN1.5 group) significantly promoted the growth of Vallisneria natans leaves and roots. Comparing the final pollutant proportions in different environmental media, concentrations in water (0.20%-1.8%), clam accumulation (0.032%-0.11%), and plant absorption (0.10%-0.44%) constituted a minimal portion of the overall pollutant load in the system. The majority of pollutants (24%-65%) were degraded in the aquaculture environment, with microbial degradation likely playing a predominant role. Bacterial phyla, particularly Proteobacteria and Firmicutes, were identified as potential direct contributors to pollutant degradation in the Vallisneria natans-biochar system.

AI-assisted systematic review on remediation of contaminated soils with PAHs and heavy metals

This systematic review addresses soil contamination by crude oil, a pressing global environmental issue, by exploring effective treatment strategies for sites co-contaminated with heavy metals and polycyclic aromatic hydrocarbons (PAHs). Our study aims to answer pivotal research questions: (1) What are the interaction mechanisms between heavy metals and PAHs in contaminated soils, and how do these affect the efficacy of different remediation methods? (2) What are the challenges and limitations of combined remediation techniques for co-contaminated soils compared to single-treatment methods in terms of efficiency, stability, and specificity? (3) How do various factors influence the effectiveness of biological, chemical, and physical remediation methods, both individually and combined, in co-contaminated soils, and what role do specific agents play in the degradation, immobilization, or removal of heavy metals and PAHs under diverse environmental conditions? (4) Do AI-powered search tools offer a superior alternative to conventional search methodologies for executing an exhaustive systematic review? Utilizing big-data analytics and AI tools such as Litmaps.co, ResearchRabbit, and MAXQDA, this study conducts a thorough analysis of remediation techniques for soils co-contaminated with heavy metals and PAHs. It emphasizes the significance of cation-π interactions and soil composition in dictating the solubility and behavior of these pollutants. The study pays particular attention to the interplay between heavy metals and PAH solubility, as well as the impact of soil properties like clay type and organic matter on heavy metal adsorption, which results in nonlinear sorption patterns. The research identifies a growing trend towards employing combined remediation techniques, especially biological strategies like biostimulation-bioaugmentation, noting their effectiveness in laboratory settings, albeit with potentially higher costs in field applications. Plants such as Medicago sativa L. and Solanum nigrum L. are highlighted for their effectiveness in phytoremediation, working synergistically with beneficial microbes to decompose contaminants. Furthermore, the study illustrates that the incorporation of biochar and surfactants, along with chelating agents like EDTA, can significantly enhance treatment efficiency. However, the research acknowledges that varying environmental conditions necessitate site-specific adaptations in remediation strategies. Life Cycle Assessment (LCA) findings indicate that while high-energy methods like Steam Enhanced Extraction and Thermal Resistivity - ERH are effective, they also entail substantial environmental and financial costs. Conversely, Natural Attenuation, despite being a low-impact and cost-effective option, may require prolonged monitoring. The study advocates for an integrative approach to soil remediation, one that harmoniously balances environmental sustainability, cost-effectiveness, and the specific requirements of contaminated sites. It underscores the necessity of a holistic strategy that combines various remediation methods, tailored to meet both regulatory compliance and the long-term sustainability of decontamination efforts.

Formation mechanisms and degradation methods of polycyclic aromatic hydrocarbons in biochar: A review

Biochar has been widely used in soil amendment and environmental remediation. Polycyclic aromatic hydrocarbons (PAHs) could be produced in preparation of biochar, which may pose potential risks to the environment and human health. At present, most studies focus on the ecotoxicity potential of biochar, while there are few systematic reviews on the formation mechanisms and mitigation strategies of PAHs in biochar. Therefore, a systematical understanding of the distribution, formation mechanisms, risk assessment, and degradation approaches of PAHs in biochar is highly needed. In this paper, the distribution and content of the total and bioavailable PAHs in biochar are reviewed. Then the formation mechanisms, influencing factors, and potential risk assessment of PAHs in biochar are systematically explored. After that, the effective strategies to alleviate PAHs in biochar are summarized. Finally, suggestions and perspectives for future studies are proposed. This review provides a guide for reducing the formation of biochar-associated PAHs and their toxicity, which is beneficial for the development and large-scale safe use of environmentally friendly biochar.

Reduction strategies of polycyclic aromatic hydrocarbons in farmland soils: Microbial degradation, plant transport inhibition, and their mechanistic analysis

This study focuses on the abatement of polycyclic aromatic hydrocarbons (PAHs), a global pollutant, in farmland soils. Seven controlled PAHs in China were used as the target ligands, and four key target receptors degradable PAHs and two key target receptors transport PAHs were used as the target receptors. Firstly, the degradation abilities of the four key target receptors on PAHs were quantified, and the dominant target receptors that could efficiently degrade PAHs were screened out. Then, the co-degradation abilities of PAHs under the coexistence of the dominant target receptors (microbial diversity) were assessed, and 30 external condition-adding schemes to promote the microbial (co-)degradation of PAHs were designed. In addition, the microbial dominant target receptor mutants and the plant key target receptor mutants were obtained, the degradation and transportation of PAHs were improved by 8.06%∼22.27% and 39.86%∼45.43%. Finally, the mechanism analysis of PAHs biodegradation and transportation found that the Van der Waals interactions dominated the enhancement of PAHs' degradation in soil, and the solvation capacity dominated the decrease of PAHs' transportation in plant. This study aims to provide theoretical support for the prevention and control of PAHs residue pollution in farmland soil, as well as the protection of human dietary health.

In vitro assessment of crude oil degradation by Acinetobacter junii and Alcanivorax xenomutans isolated from the coast of Ghana

This study was aimed at using in vitro microcosm experiments to assess crude oil degradation efficiency of Acinetobacter junii and Alcanivorax xenomutans isolated along Ghana's coast. Uncontaminated seawater from selected locations along the coast was used to isolate bacterial species by employing enrichment culture procedures with crude oil as the only carbon source. The isolates were identified by means of the extended direct colony transfer method of the Matrix Assisted Laser Desorption Ionization Time of Flight Mass Spectroscopy (MALDI-TOF MS), as Acinetobacter junii, and Alcanivorax xenomutans. Remediation tests showed that Acinetobacter junii yielded degradation efficiencies of 27.59 %, 41.38 % and 57.47 %. Whereas efficiencies of 21.14 %, 32.18 % and 43.68 % were recorded by Alcanivorax xenomutans representing 15, 30 and 45 days respectively. Consortia of Acinetobacter junii, and Alcanivorax xenomutans also yielded 32.18 %, 48.28 % and 62.07 % for the selected days respectively. Phylogenetic characterization using ClustalW and BLAST of sequences generated from the Oxford Nanopore Sequencing technique, showed that the Ghanaian isolates clustered with Alcanivorax xenomutans and Acinetobacter junii species respectively. An analysis of the sequenced data for the 1394-bp portion of the 16S rRNA gene of the isolates revealed >99 % sequence identity with the isolates present on the GenBank database. The isolates of closest identity were Alcanivorax xenomutans and Acinetobacter junii with accession numbers, NR_133958.1 and KJ147060.1 respectively. Acinetobacter junii and Alcanivorax xenomutans isolated from Ghana's coast under pristine seawater conditions have therefore demonstrated their capacity to be used for the remediation of crude oil spills.

Factors regulating interaction among inorganic nitrogen and phosphorus species, plant uptake, and relevant cycling genes in a weakly alkaline soil treated with biochar and inorganic fertilizer

To highlight how biochar affects the interaction between inorganic nitrogen species (ammonium nitrogen, nitrate nitrogen, and nitrite nitrogen: NH4+-N, NO3¯-N, and NO2¯-N) and phosphorus species (calcium phosphate, iron phosphate, and aluminum phosphate: CaP, FeP and AlP) in soil and plant uptake of these nutrients, walnut shell (WS)- and corn cob (CC)-derived biochars (0.5 %, 1 %, 2 %, and 4 %, w/w) were added to a weakly alkaline soil, and then Chinese cabbages were planted. The results showed that the changes in soil inorganic nitrogen were related to biochar feedstock, pyrolysis temperature, and application rate. For soil under the active nitrification condition (dominant NO3¯-N), a significant decrease in the NH4+-N/NO3¯-N ratio after biochar addition indicates enhanced nitrification (excluding WS-derived biochars at 2 % and 4 %), which can be explained by the most positive response of ammonia-oxidizing archaeal amoA to biochar addition. The CC-derived biochar more effectively enhanced soil nitrification than WS-derived biochar did. The addition of 4 % of biochars significantly increased soil inorganic phosphorus, and the addition of CC-derived biochars more effectively increased Ca2P than WS-derived biochars. Biochars significantly decreased plant uptake of phosphorus, while generally had little influence on plant uptake of nitrogen. Interestingly, NO2¯-N in soil significantly positively correlated with total phosphorus in both soil and plant, and significantly negatively correlated with phoC, indicating that a certain degree of NO2¯-N accumulation in soil slightly facilitated plant uptake of phosphorus but inhibited phoC-harboring bacteria. The NO3¯-N in soil significantly positively correlated with Ca2P and Ca8P, while the NH4+-N/NO3¯-N ratio significantly negatively correlated with Ca10P and FeP, indicating that the enhanced nitrification seemed to facilitate the change in phosphorus to readly available ones. This study will help determine how to scientifically and rationally use biochar to regulate inorganic nitrogen and phosphorus species in soil and plant uptake of these nutrients.

Microplastics reduced bioavailability and altered toxicity of phenanthrene to maize (Zea mays L.) through modulating rhizosphere microbial community and maize growth

Due to its large specific surface area and great hydrophobicity, microplastics can adsorb polycyclic aromatic hydrocarbons (PAHs), affecting the bioavailability and the toxicity of PAHs to plants. This study aimed to evaluate the effects of D550 and D250 (with diameters of 550 μm and 250 μm) microplastics on phenanthrene (PHE) removal from soil and PHE accumulation in maize (Zea mays L.). Moreover, the effects of microplastics on rhizosphere microbial community of maize grown in PHE-contaminated soil would also be determined. The results showed that D550 and D250 microplastics decreased the removal of PHE from soil by 6.5% and 2.7% and significantly reduced the accumulation of PHE in maize leaves by 64.9% and 88.5%. Interestingly, D550 microplastics promoted the growth of maize and enhanced the activities of soil protease and alkaline phosphatase, while D250 microplastics significantly inhibited the growth of maize and decreased the activities of soil invertase, alkaline phosphatase and catalase, in comparison with PHE treatment. In addition, microplastics changed the rhizosphere soil microbial community and reduced the relative abundance of PAHs degrading bacteria (Pseudomonas, Massilia, Proteobacteria), which might further inhibit the removal of PHE from soil. This study provided a new perspective for evaluating the role of microplastics on the bioavailability of PHE to plants and revealing the combined toxicity of microplastics and PHE to soil microcosm and plant growth.

Biochar for soil remediation: A comprehensive review of current research on pollutant removal

Biochar usage in soil remediation has turned out to be an enticing topic recently. Biochar, a product formed by pyrolysis of organic waste, which is rich in carbon, has the aptitude to ameliorate climate change by sequestering carbon while also enhancing soil quality and crop yields. Two-edged implications of biochar on soil amendment are still being discussed yet, clarity on the long-term implications of biochar on soil health and the environment is not yet achieved. As a result, it is crucial to systematically uncover the pertinent information regarding biochar remediation, as this can serve as a roadmap for future research on using biochar to remediate contaminated soils in mining regions. This review endeavors to bring forth run thoroughly the latest state of research on the use of biochar in soil remediation, along with its potential benefits, limitations, challenges, and future scope. By synthesizing existing literature on biochar soil remediation, this review aims to provide insights into the potential of biochar as a sustainable solution for soil remediation. Specifically, this review will highlight the key factors that influence the effectiveness of biochar for soil remediation and the potential risks associated with its use, as well as the current gaps in knowledge and future research directions.

Biochar alters the persistence of PAHs in soils by affecting soil physicochemical properties and microbial diversity: A meta-analysis

Polycyclic aromatic hydrocarbons (PAHs) pollution in soil is a pervasive environmental issue worldwide. Although biochar has the potential to immobilize PAHs in soils, there remains a study gap in the use of systematic analyses to assess the effectiveness of biochar for PAH removal and the factors that affect biochar. Hence, a meta-analysis utilizing 56 published studies was aimed to assess the impact of biochar on the PAH content, soil physicochemical properties, and microbial diversity in PAH-contaminated soils and to elucidate what factors impact the capability of biochar to alter PAH persistence. With biochar application, soil Ctot PAH concentrations were significantly reduced (15.4%), while the levels of Cfree PAHs and Cbioacc PAHs were reduced by 55.6% and 46.5%, respectively. Additionally, biochar improved the physicochemical properties of PAH-contaminated soil and increased the diversity of microorganisms. Particularly, the relative abundance of PAH degraders increased significantly (43.7%), which indicated that PAH biodegradation was significantly enhanced. Soil physicochemical properties and biochar production conditions are indispensable for the study of the PAH persistence. The overall findings revealed that the pyrolysis of woody biochar at 300-500 °C was beneficial for reducing the PAH persistence in acidic, coarse, or fine and high soil organic matter content (>20 g/kg) soils.

Understanding of Co-boiling between Organic Contaminants and Water during Thermal Remediation: Effects of Nonequilibrium Heat and Mass Transport

In situ thermal desorption (ISTD) provides an efficient solution to remediation of soil and groundwater contaminated with nonaqueous phase liquids (NAPLs). Establishing a relationship between the subsurface temperature rise and NAPL removal is significant to reduce energy consumption of ISTD. However, the co-boiling phenomenon between NAPL and water poses a great challenge in developing this relationship due to the nonequilibrium heat and mass transport effects. We performed a systematic experimental investigation into the local temperature rise patterns at different distances from a NAPL pool and under different degrees of superheat by selecting four representative NAPLs (i.e., trichloroethylene, tetrachlorethylene, n-hexane, and n-octane) according to their density and boiling point relative to water. The patterns of temperature rise indicated that the underground temperature field can be divided into three zones: the zone of local thermal equilibrium, the nonequilibrium zone affected by co-boiling, and the zone unaffected by co-boiling. We developed a pattern-recognition-based approach, which considers the effects of local heat and mass transport to establish a qualitative correlation between the temperature rise and NAPL removal. Our results give deeper insights into the understanding of subsurface temperatures in ISTD practice, which can serve as the guideline for more accurate and sustainable remediation.

Analysis of natural photocatalysts derived from spartina alterniflora with superior removal performance of pollutant

Spartina alterniflora, as an invasive alien species, has been studied in terms of its potential use in immobilization and synergistic photocatalysis against dye contaminants for the first time. Microscopic characterization and Fourier transform infrared (FTIR) spectroscopy results confirmed the presence of abundant 3D wormhole-like pore structures and active functional groups (-OH, -NH2, CO, Si-O-Si). Moreover, the existence of SiO2 was connected the metal oxides with polar groups, which could proceed entire reaction procedure subsequently. Transition metal oxides (such as Fe2O3, TiO2, MnO2 and NiO) contained in photocatalysts might effectively promote the organics decomposition by the visible light excitation. The highest dye removal efficiency of 92.03% could be reached with the addition of 0.02 g photocatalyst. The capture experiment confirmed that the h+ was the dominant active substance during the photocatalytic degradation process. Density functional theory (DFT) calculations verified that the functional groups (-COOH, -OH and -NH2) were exceptional adsorption sites for catalyst, and the calculated adsorption energy were all negative with the order of SRHH-NH2 (-2.712688 eV) < SRHH-OH (-2.075601 eV) < SRHH-COOH (-1.283141 eV), which confirmed that interface interaction effectively bound cationic dyes through the formation of hydrogen bonds at the catalysts-water interface, further accelerating the reaction rate of the entire photocatalytic reduction of dye molecules. Therefore, this work provides a feasible synthesis of natural photocatalysts using solid waste, which suggests excellent adsorption and photocatalysis properties for the treatment of organic industrial pollutant.

Preferential association of polycyclic aromatic hydrocarbons (PAHs) with soil colloids at an e-waste recycling site: Implications for risk of PAH migration to subsurface environment

Polycyclic aromatic hydrocarbon (PAH) contamination at e-waste recycling sites poses high ecological and human-health risks. Of note, PAHs in surface soils can be mobilized through colloid-facilitated transport, and may migrate into the subsurface and pollute groundwater. Here, we show that the colloids released from the soil samples at an e-waste recycling site in Tianjin, China contain high concentrations of PAHs, with total concentrations of 16 PAHs as high as 1520 ng/g dw. Preferential association of the PAHs with the colloids is observed, with the distribution coefficients of PAHs between colloids and bulk soil often above 10. Source diagnostic ratios show that soot-like particles are the main source of PAHs at the site, due to the incomplete combustion of fossil fuels, biomass, and electronic wastes during the e-waste dismantling practices. Due to their small sizes, a large fraction of these soot-like particles can be remobilized as colloids, and this explains the preferential association of PAHs with colloids. Moreover, the colloids-soil distribution coefficients are higher for the low-molecular-weight PAHs than for the high-molecular-weight ones, possibly attributable to the different binding routes/modes of these two groups of PAHs to the particles during combustion. Notably, the preferential association of PAHs with colloids is even more pronounced for the subsurface soils, corroborating that the presence of PAHs in the deeper soils is primarily the results of downward migration of PAH-bearing colloids. The findings highlight the important role of colloids as a vector for the subsurface transport of PAHs at e-waste recycling sites, and call for further understanding of colloid-facilitated transport of PAHs at e-waste recycling sites.

Cigarette: an unsung anthropogenic evil in the environment

The world's population is growing steadily, and this trend is mirrored by a sharp rise in the number of people who smoke cigarettes. Instead of properly disposing of their cigarette waste, most people simply toss them aside, leading to serious environmental consequences. According to previous statistics, in 2012 alone, 6.25 trillion cigarettes were consumed by 967 million chain smokers. Past studies have shown that up to 30% of global litter is made up of cigarette waste. These discarded cigarette butts are non-biodegradable and contain over 7000 toxicants such as benzene, 1,3-butadiene, nitrosamine ketone, N-Nitrosonornicotine, nicotine, formaldehyde, acrolein, ammonia, aniline, polycyclic aromatic hydrocarbons, and various heavy metals. These toxicants have a negative impact on the habitats of wildlife and can cause serious health problems such as cancer, respiratory disorders, cardiac issues, and sexual dysfunction. Although it is still unclear how littered cigarettes affect plant growth, germination, and development, it is clear that they have the potential to harm plant health. Just like single-use plastic, trashed cigarette butts are a critical new rising form of pollution that requires scientific attention for effective recycling and disposal management. It is important to properly dispose of cigarette waste to protect the environment and wildlife, as well as to prevent harm to human health.

Detection of 1-OHPyr in human urine using SERS with injection under wet liquid-liquid self-assembled films of β-CD-coated gold nanoparticles and deep learning

1-Hydroxypyrene (1-OHPyr), a typical hydroxylated polycyclic aromatic hydrocarbon (OH-PAH), has been commonly regarded as a urinary biomarker for assessing human exposure and health risks of PAHs. Herein, a fast and sensitive method was developed for the determination of 1-OHPyr in urine using surface-enhanced Raman spectroscopy (SERS) combined with deep learning (DL). After emulsification, urinary 1-OHPyr was separated using simple liquid-liquid extraction. Gold nanoparticles with β-cyclodextrin (β-CD@AuNPs) were synthesized, and homogeneous and ordered β-CD@AuNP films were prepared through a liquid-liquid interface self-assembly process. The separated 1-OHPyr was injected under wet assembled films for SERS detection. Concentration as low as 0.05 μg mL^-1 of 1-OHPyr in urine could still be detected, and the relative standard deviation was 5.5 %, and this was ascribed to the adsorption of β-CD and the high-probability contact between 1-OHPyr molecules and the nanogap of assembled films under the action of capillary force. Meanwhile, a convolutional neural network (CNN), a classical DL network architecture, was adopted to build the prediction model, and the model was further simplified by genetic algorithm (GA). CNN combined with a GA obtained optimized results with determination coefficient and a root mean square error of prediction sets of 0.9639 and 0.6327, respectively, outperforming other models. Overall, the proposed method achieves fast and accurate detection of 1-OHPyr in urine, improves the assessment human exposure to PAHs and is expected to have applications in the analysis of other OH-PAHs in complex environments.

Biochar as a Green Sorbent for Remediation of Polluted Soils and Associated Toxicity Risks: A Critical Review

Soil contamination with organic contaminants and various heavy metals has become a global environmental concern. Biochar application for the remediation of polluted soils may render a novel solution to soil contamination issues. However, the complexity of the decontaminating mechanisms and the real environment significantly influences the preparation and large-scale application of biochar for soil ramification. This review paper highlights the utilization of biochar in immobilizing and eliminating the heavy metals and organic pollutants from contaminated soils and factors affecting the remediation efficacy of biochar. Furthermore, the risks related to biochar application in unpolluted agricultural soils are also debated. Biochar production conditions (pyrolysis temperature, feedstock type, and residence time) and the application rate greatly influence the biochar performance in remediating the contaminated soils. Biochars prepared at high temperatures (800 °C) contained more porosity and specific surface area, thus offering more adsorption potential. The redox and electrostatic adsorption contributed more to the adsorption of oxyanions, whereas ion exchange, complexation, and precipitation were mainly involved in the adsorption of cations. Volatile organic compounds (VOCs), dioxins, and polycyclic aromatic hydrocarbons (PAHs) produced during biochar pyrolysis induce negative impacts on soil alga, microbes, and plants. A careful selection of unpolluted feedstock and its compatibility with carbonization technology having suitable operating conditions is essential to avoid these impurities. It would help to prepare a specific biochar with desired features to target a particular pollutant at a specific site. This review provided explicit knowledge for developing a cost-effective, environment-friendly specific biochar, which could be used to decontaminate targeted polluted soils at a large scale. Furthermore, future study directions are also described to ensure a sustainable and safe application of biochar as a soil improver for the reclamation of polluted soils.

Surfactant-Containing Foam Effectively Enhanced the Removal of Polycyclic Aromatic Hydrocarbons from Heavily Contaminated Soil

Surfactant remediation has an excellent record of removing polycyclic aromatic hydrocarbons (PAHs). By using simulation experiments, we investigated the properties and mechanism of a surfactant-containing foam and its effect on PAH removal. Our results suggest that the optimal conditions by foam washing are as follows: 40 mmol·L^-1 of rhamnolipid and fulvic acid mixed surfactant (V: V = 3:1), with 70:3 and 20:3 foam gas-liquid ratio for naphthalene and phenanthrene, respectively (pH 6, 50°C, 2 h). Under the optimal conditions, 60.1% and 56.68% removal efficiencies were achieved against naphthalene and phenanthrene from contaminated soil, respectively. These values were lower than those from the simulated media (76.69% and 70.43% for naphthalene and phenanthrene, respectively). The strong PAH adsorption on the soil particles antagonized volatilization, the key PAH removal mechanism by foam leaching. Therefore, this research provides relevant information for using surfactant foam to remediate heavily PAH-contaminated soils.

Remediation of Pb-contaminated soil using biochar-based slow-release P fertilizer and biomonitoring employing bioindicators

Soil contamination by Pb can result from different anthropogenic sources such as lead-based paints, gasoline, pesticides, coal burning, mining, among others. This work aimed to evaluate the potential of P-loaded biochar (Biochar-based slow-release P fertilizer) to remediate a Pb-contaminated soil. In addition, we aim to propose a biomonitoring alternative after soil remediation. First, rice husk-derived biochar was obtained at different temperatures (450, 500, 550, and 600 °C) (raw biochars). Then, part of the resulting material was activated. Later, the raw biochars and activated biochars were immersed in a saturated KH₂PO₄ solution to produce P-loaded biochars. The ability of materials to immobilize Pb and increase the bioavailability of P in the soil was evaluated by an incubation test. The materials were incorporated into doses of 0.5, 1.0, and 2.0%. After 45 days, soil samples were taken to biomonitor the remediation process using two bioindicators: a phytotoxicity test and enzyme soil activity. Activated P-loaded biochar produced at 500 °C has been found to present the best conditions for soil Pb remediation. This material significantly reduced the bioavailability of Pb and increased the bioavailability of P. The phytotoxicity test and the soil enzymatic activity were significantly correlated with the decrease in bioavailable Pb but not with the increase in bioavailable P. Biomonitoring using the phytotoxicity test is a promising alternative for the evaluation of soils after remediation processes.

Enhanced Bioremediation of Aged Polycyclic Aromatic Hydrocarbons in Soil Using Immobilized Microbial Consortia Combined with Strengthening Remediation Strategies

Microbial biodegradation is considered as one of the most effective strategies for the remediation of soil contaminated with polycyclic aromatic hydrocarbons (PAHs). To improve the degradation efficiency of PAHs, PAH-degrading consortia combined with strengthening remediation strategies was used in this study. The PAH biodegrading performance of seven bacterial consortia constructed by different ratios of Mycobacterium gilvum MI, Mycobacterium sp. ZL7 and Rhodococcus rhodochrous Q3 was evaluated in an aqueous system containing phenanthrene, pyrene, benzo[a]pyrene and benzo[b]fluoranthene. Bacterial consortium H6 (Q3:ZL7:MI = 1:2:2) performed a high degrading efficiency of 59% in 8 days. The H6 was subsequently screened to explore its potential ability and performance to degrade aged PAHs in soils from a coking plant and the effects of strengthening strategies on the aged PAH degradation, including the addition of glucose or sodium dodecyl benzene sulfonate (SDBS) individually or as a mixture along immobilization of the inoculant on biochar. The highest degradation efficiencies, which were 15% and 60% for low-molecular-weight (LMW) PAHs and high-molecular-weight (HMW) PAHs, respectively, were observed in the treatment using immobilized microbial consortium H6 combined with the addition of glucose and SDBS after 24 days incubation. This study provides new insights and guidance for future remediation of aged PAH contaminated soils.

The co-application of biochar with bioremediation for the removal of petroleum hydrocarbons from contaminated soil

Soil pollution from petroleum hydrocarbon is a global environmental problem that could contribute to the non-actualisation of the United Nations Sustainable Development Goals. Several techniques have been used to remediate petroleum hydrocarbon-contaminated soils; however, there are technical and economical limitations to existing methods. As such, the development of new approaches and the improvement of existing techniques are imperative. Biochar, a low-cost carbonaceous product of the thermal decomposition of waste biomass has gained relevance in soil remediation. Biochar has been applied to remediate hydrocarbon-contaminated soils, with positive and negative results reported. Consequently, attempts have been made to improve the performance of biochar in the hydrocarbon-based remediation process through the co-application of biochar with other bioremediation techniques as well as modifying biochar properties before use. Despite the progress made in this domain, there is a lack of a detailed single review consolidating the critical findings, new developments, and challenges in biochar-based remediation of petroleum hydrocarbon-contaminated soil. This review assessed the potential of biochar co-application with other well-known bioremediation techniques such as bioaugmentation, phytoremediation, and biostimulation. Additionally, the benefits of modification in enhancing biochar suitability for bioremediation were examined. It was concluded that biochar co-application generally resulted in higher hydrocarbon removal than sole biochar treatment, with up to a 4-fold higher removal observed in some cases. However, most of the biochar co-applied treatments did not result in hydrocarbon removal that was greater than the additive effects of individual treatment. Overall, compared to their complementary treatments, biochar co-application with bioaugmentation was more beneficial in hydrocarbon removal than biochar co-application with either phytoremediation or biostimulation. Future studies should integrate the ecotoxicological and cost implications of biochar co-application for a viable remediation process. Lastly, improving the synergistic interactions of co-treatment on hydrocarbon removal is critical to capturing the full potential of biochar-based remediation.

Biochar application strategies for polycyclic aromatic hydrocarbons removal from soils

Polycyclic aromatic hydrocarbons (PAHs) are known as a hazardous group of pollutants in the soil which causes many challenges to the environment. In this study, the potential of biochar (BC), as a carbonaceous material, is evaluated for the immobilization of PAHs in soils. For this purpose, various bonding mechanisms of BC and PAHs, and the strength of bonds are firstly described. Also, the effect of impressive criteria including BC physicochemical properties (such as surface area, porosity, particle size, polarity, aromaticity, functional group, etc., which are mostly the function of pyrolysis temperature), number of rings in PAHs, incubation time, and soil properties, on the extent and rate of PAHs immobilization by BC are explained. Then, the utilization of BC in collaboration with biological tools which simplifies further dissipation of PAHs in the soil is described considering detailed interactions among BC, microbes, and plants in the soil matrix. The co-effect of BC and biological remediation has been authenticated by previous studies. Moreover, recent technologies and challenges related to the application of BC in soil remediation are explained. The implementation of a combined BC-biological remediation method would provide excellent prospects for PAHs-contaminated soils.

Simultaneous Prediction, Determination, and Extraction of Four Polycyclic Aromatic Hydrocarbons in the Environment Using a UCON-NaH2PO4 Aqueous Two-Phase Extraction System Combined with High-Performance Liquid Chromatography-Ultraviolet Detection

In this paper, a new aqueous two-phase extraction system(ATPES) consisting of UCON (poly(ethylene glycol-ran-propylene glycol) monobutyl ether)-NaH₂PO₄ was established, and four trace polycyclic aromatic hydrocarbons (PAHs: fluorene, anthracene, pyrene and phenanthrene) in water and soil were analyzed by high-performance liquid chromatography (HPLC)-ultraviolet detection. In the multi-factor experiment, the central composite design (CCD) was used to determine the optimum technological conditions. The final optimal conditions were as follows: the concentration of UCON was 0.45 g·mL^-1, the concentration of NaH₂PO₄ was 3.5 mol·L^-1, and the temperature was 30 °C. The recovery of the four targets was 98.91-99.84% with a relative standard deviation of 0.3-2.1%. Then UCON recycling and cyclic tests were designed in the experiment, and the results showed that the recovery of PAHs gradually increased in the three extractions because of the remaining PAHs in the salt phase of last extraction. The recovery of PAHs in the UCON recycling test was less than that in the extraction test due to the wastage of UCON. In addition, a two-phase aqueous extraction model was established based on the random forest (RF) model. The results obtained were compared with the experimental data, and the root mean square error (RMSE) was 0.0371-0.0514 and the correlation coefficient R² was 96.20-98.53%, proving that the model is robust and reliable.

Metagenomic Analysis of Microbial Alliances for Efficient Degradation of PHE: Microbial Community Structure and Reconstruction of Metabolic Network

Polycyclic aromatic hydrocarbons are a widespread organic pollutant worldwide. In this study, a highly efficient phenanthrene (PHE)-degrading microbial community was enriched from oil extraction soil, which could degrade 500 mg/L PHE within 4 days. Using 16S rRNA sequencing, the dominant bacteria in this community at the phylum level were found to be Proteobacteria, Actinobacteria, and Firmicutes. Metagenomic annotation of genes revealed the metabolic pathways and the contribution of different bacteria to the degradation process. Pseudomonadaceae contributed multiple functional genes in the degradation process. This study revealed the functional genes, metabolic pathways, and microbial interactions of the microbial community, which are expected to provide guidance for practical management.

Rhamnolipid-Enhanced ZVI-Activated Sodium Persulfate Remediation of Pyrene-Contaminated Soil

In soil, polycyclic aromatic hydrocarbons (PAHs) are tightly bound to organic components, but surfactants can effectively transform them from a solid to a liquid phase. In this study, the biosurfactant rhamnolipid (RL) was selected as the eluent; shaking elution in a thermostatic oscillator improved the elution rate of pyrene, and the effects of RL concentration, temperature, and elution time on the elution effect were compared. After four repeated washings, the maximum elution rate was 75.6% at a rhamnolipid concentration of 20 g/L and a temperature of 45 °C. We found that 38 μm Zero-Valent Iron (ZVI) had a higher primary reaction rate (0.042 h^-1), with a degradation rate of 94.5% when 3 g/L ZVI was added to 21 mM Na₂S₂O₈ at 60 °C. Finally, electron paramagnetic resonance (EPR) detected DMPO-OH and DMPO-SO₄ signals, which played a major role in the degradation of pyrene. Overall, these results show that the combination of rhamnolipid elution and persulfate oxidation system effectively remediated pyrene-contaminated soil and provides some implications for the combined remediation with biosurfactants and chemical oxidation.

Composition of PAHs in Biochar and Implications for Biochar Production

The content of polycyclic aromatic hydrocarbons (PAHs) in biochar has been studied extensively; however, the links between biomass feedstock, production process parameters, and the speciation of PAHs in biochar are understudied. Such an understanding is crucial, as the health effects of individual PAHs vary greatly. Naphthalene (NAP) is the least toxic of the 16 US EPA PAHs but comprises the highest proportion of PAHs in biochar. Therefore, we investigate which parameters favor high levels of non-NAP PAHs (∑16 US EPA PAHs without NAP) in a set of 73 biochars. On average, the content of non-NAP PAHs was 9 ± 29 mg kg^-1 (median 0.9 mg kg^-1). Importantly, during the production of the biochars with the highest non-NAP PAH contents, the conditions in the post-pyrolysis area, where pyrolysis vapors and biochar are separated, favored condensation and deposition of PAHs on biochar. Under these conditions, NAP condensed to a lower degree because of its high vapor pressure. In biochars not contaminated through this process, the average non-NAP content was only 2 ± 3 mg kg^-1 (median 0.5 mg kg^-1). Uneven heat distribution and vapor trapping during pyrolysis and cool zones in the post-pyrolysis area need to be avoided. This demonstrates that the most important factor yielding high contents of toxic PAHs in biochar was neither a specific pyrolysis parameter nor the feedstock but the pyrolysis unit design, which can be modified to produce clean and safe biochar.

Adsorption mechanism of polycyclic aromatic hydrocarbons using wood waste-derived biochar

The polycyclic aromatic hydrocarbons (PAHs) have been attracted increasing attentions due to their carcinogenicity and teratogenicity. Adsorption is widely considered one of the most potential technologies for PAHs removal. In this study, we prepared two kinds of oxygen-rich biochar derived from waste wood to investigate the PAHs adsorption performance, and the molecular simulation was used to build the 16 priority PAHs, 23 nitrated PAHs, 9 oxygenated PAHs adsorption model. The surface adsorption performance of oxygen-rich biochar significantly depends on the pyrolysis conditions. The main out-comings demonstrated that the adsorption of naphthalene (C₁₀H₈) molecules first occurred, and the optimal adsorption positions of oxygen-rich biochar strongly adhered to functional groups of carboxyl and hydroxyl. Moreover, benzene ring, -COOH, and -CH₃ of biochar were the main adsorbed functional groups for PAHs adsorption. The oxygen-rich biochar had the targeted-adsorption effect on PAHs removal especially symmetrical PAHs, and the targeted-adsorption mechanism was finally proposed. The research is beneficial to guide the removal of PAHs from polluted water and mitigate the environmental pollution caused by biomass waste mismanagement, simultaneously.

Temporal changes of microbial community structure and nitrogen cycling processes during the aerobic degradation of phenanthrene

Phenanthrene (PHE) is frequently detected in worldwide soils. But it is still not clear that how the microbial community succession happens and the nitrogen-cycling processes alter during PHE degradation. In this study, the temporal changes of soil microbial community composition and nitrogen-cycling processes during the biodegradation of PHE (12 μg g^-1) were explored. The results showed that the biodegradation of PHE followed the second-order kinetics with a half-life of 7 days. QPCR results demonstrated that the bacteria numbers increased by 67.1%-194.7% with PHE degradation, whereas, no significant change was observed in fungi numbers. Thus, high-throughput sequencing based on 16 S rRNA was conducted and showed that the abundances of Methylotenera, Comamonadaceae, and Nocardioides involved in PHE degradation and denitrification were significantly increased, while those of nitrogen-metabolism-related genera such as Nitrososphaeraceae, Nitrospira, Gemmatimonadacea were decreased in PHE-treated soil. Co-occurrence network analysis suggested that more complex interrelations were constructed, and Proteobacteria instead of Acidobacteriota formed intimate associations with other microbes in responding to PHE exposure. Additionally, the abundances of nifH and narG were significantly up-regulated in PHE-treated soil, while that of amoA especially AOAamoA was down-regulated. Finally, correlation analysis found several potential microbes (Methylotenera, Comamonadaceae, and Agromyces) that could couple PHE degradation and nitrogen transformation. This study confirmed that PHE could alter microbial community structure, change the native bacterial network, and disturb nitrogen-cycling processes.

Evaluating the bio-removal of crude oil by vetiver grass (Vetiveria zizanioides L.) in interaction with bacterial consortium exposed to contaminated artificial soils

Remediation of crude oil-impacted areas is a major pervasive concern in various environmental conditions. The major aim of this study was to investigate the collaboration of vetiver grass (Vetiveria zizanioides L.) and petroleum hydrocarbon-degrading bacteria to clean up contaminated soils. Vetiver grass and five native bacterial isolates were used in one consortium to remediate contaminated soil by crude oil at various concentrations (2.0, 4.0, 6.0 8.0, 10, and 12.0% w_oil/w_soil). The presence of isolated bacteria caused a significant (p < 0.05) increment of root-shoot ratio of vetiver in contaminated soils in comparison to non-contaminated soil. The combination of vetiver and bacterial consortium revealed efficient dissipation of more than 30% of low-molecular-weight polycyclic aromatic hydrocarbons (PAHs) and more than 50% of high-molecular-weight PAHs in all crude oil concentrations. The removal of n-alkanes in the simultaneous presence of the bacteria and plant was more than 70.0% at 10.0% of oil concentration, whereas the removals in control were 20.7, 13.7 and 9.2%, respectively. The hydrocarbons dissipation efficiency of applied treatments decreased at 12.0% of contamination. It is concluded that a combination of vetiver grass and the isolated bacteria could be a feasible strategy for remediation of crude oil-polluted soils. Novelty statementDetermination of the responses of vetiver grass under different crude oil concentrations is one of the novelties of the present study, which is helpful for demonstrating plant tolerance on polluted environments. Also, it adds information about the potential of this grass to clean up crude oil-polluted soils solely as well as in the presence of promising selected bacterial strains.