Au-IDA microelectrodes modified with Au-doped graphene oxide for the simultaneous determination of uric acid and ascorbic acid in urine samples

Copper(II) phthalocyanine as an electrocatalytic electrode for cathodic detection of urinary tryptophan

Herein, we introduce a novel method for tryptophan detection via a reduction reaction facilitated by its interaction with a copper(II) phthalocyanine (CuPc) electrocatalytic electrode. This method addresses challenges associated with the susceptibility of the oxidation response to interference from various species when measuring tryptophan in bodily fluids. The reduction currents exhibit a linear increase with tryptophan concentrations in two ranges: 0.0013-0.10 mM and 0.10-1.20 mM, with the sensitivities of 14.7 ± 0.5 μA mM-1 and 3.5 ± 0.1 μA mM-1, respectively. The limit of detection (LOD, 3SB/m) is determined to be 0.39 μM. The sensor exhibits excellent reproducibility, with the relative standard deviation of <5%. Application of the sensor to authentic urine samples yields a % recovery of 101 ± 4%.

Methylene blue molecularly imprinted polymer for melatonin determination in urine and saliva samples

A highly sensitive and rapid electrochemical sensor was developed for detecting melatonin using a molecularly imprinted polymer (MIP) with methylene blue as the functional monomer and melatonin as the template. The MIP was synthesized via a simple electropolymerization process that did not require an initiating reagent. The sensor demonstrated good selectivity for melatonin against common interferences such as lactate, cytosine, cytidine, urea, ascorbic acid, creatine, creatinine, serotonin, and tryptophan. Melatonin detection was achieved at a potential of 0.60 V vs. Ag/AgCl with a sensitivity of 138.8 ± 4.7 µA µM‒1 in the linear range 0.097 - 200 µM and a limit of detection of 29 nM (3SB/m). The sensor exhibited excellent reproducibility and repeatability for both within (intra) and between (inter) electrodes (%RSD < 3% for n = 3). The sensor was applied to authentic urine and saliva samples with recoveries of 103 ± 1% and 102 ± 1%, respectively.

Electrodeposited copper nanoparticles for creatinine detection via the in situ formation of copper-creatinine complexes

Creatinine is an important biomarker of kidney diseases. In this work, a fast and facile electrochemical sensor was developed for creatinine detection based on the use of copper nanoparticle-modified screen-printed electrodes. The copper electrodes were prepared by simple electrodeposition of Cu²⁺ (aq). The electrochemically inactive creatinine was detected reductively via the in situ formation of copper-creatinine complexes. Two linear detection ranges, 0.28-3.0 mM and 3.0-20.0 mM, were achieved using differential pulse voltammetry, with the sensitivities of 0.824 ± 0.053 μA mM^-1 and 0.132 ± 0.003 μA mM^-1, respectively. The limit of detection was determined to be 0.084 mM. The sensor was validated in synthetic urine samples to yield 99.3% recovery (%RSD = 2.8), demonstrating high tolerance to possible interfering species. Finally, the stability of creatinine and its degradation kinetics at different temperatures were evaluated using our developed sensor. The loss of creatinine was found to be a first-order reaction with the activation energy of 64.7 kJ mol^-1.

A Review on Electrochemical Microsensors for Ascorbic Acid Detection: Clinical, Pharmaceutical, and Food Safety Applications

Nowadays, micro-sized sensors have become a hot topic in electroanalysis. Because of their excellent analytical features, microelectrodes are well-accepted tools for clinical, pharmaceutical, food safety, and environmental applications. In this brief review, we highlight the state-of-art electrochemical non-enzymatic microsensors for quantitative detection of ascorbic acid (also known as vitamin C). Ascorbic acid is a naturally occurring water-soluble organic compound with antioxidant properties and its quantitative determination in biological fluids, foods, cosmetics, etc., using electrochemical microsensors is of wide interest. Various electrochemical techniques have been applied to detect ascorbic acid with extremely high sensitivity, selectivity, reproducibility, and reliability, and apply to in vivo measurements. This review paper aims to give readers a clear view of advances in areas of electrode modification, successful strategies for signal amplification, and miniaturization techniques used in the electroanalytical devices for ascorbic acid. In conclusion, current challenges related to the microelectrodes design, and future perspectives are outlined.

Disposable electrochemical sensor combined with molecularly imprinted solid-phase extraction for catabolites detection of flavan-3-ol in urine samples

Polyphenols are bioactive substances of vegetal origin with a significant impact on human health. The assessment of polyphenol intake and excretion is therefore important. In this work, a new electrochemical approach based on molecularly imprinted polymer extraction and preconcentration, combined with a disposable carbon screen-printed sensor and adsorptive transfer differential pulse voltammetry detection has been proposed for quantifying of 4-hydroxyphenylacetic acid (4-HPA), which is a biomarker of flavan-3-ols intake, and other phenolic acids. The simple experimental performance has allowed the rapid data collection with relevant information about the profile of catabolites extracted. The method was validated over a concentration range of 10-200 mg L^-1, R² > 0.999. In the optimized conditions, the recovery value was 94% with RSD 8%. The limits of detection and quantification were 2.38 mg L^-1 and 7.21 mg L^-1, respectively. The method was validated by means of a chromatographic method, being the differences between the values of the 4-HPA concentrations obtained by both methods under 1%. The proposed method showed high recoveries, low detection limit, and good accuracy, providing a fast, reliable, and cheap procedure to quantify phenolic metabolites in urine, and representing therefore a good and interesting alternative method. Also, the procedure offers other advantages, including the miniaturization, the low use of organic solvents, the ability to analyse small volumes of samples, in situ analysis and simple instrumentation requirement.

A Comparison of Uric Acid Optical Detection Using as Sensitive Materials an Amino-Substituted Porphyrin and Its Nanomaterials with CuNPs, PtNPs and Pt@CuNPs

Hybrid nanomaterials consisting in 5,10,15,20-tetrakis(4-amino-phenyl)-porphyrin (TAmPP) and copper nanoparticles (CuNPs), platinum nanoparticles (PtNPs), or both types (Pt@CuNPs) were obtained and tested for their capacity to optically detect uric acid from solutions. The introduction of diverse metal nanoparticles into the hybrid material proved their capacity to improve the detection range. The detection was monitored by using UV-Vis spectrophotometry, and differences between morphology of the materials were performed using atomic force microscopy (AFM). The hybrid material formed between porphyrin and PtNPs hasthe best and most stable response for uric acid detection in the range of 6.1958 × 10−6–1.5763 × 10−5 M, even in the presence of very high concentrations of the interference species present in human environment.

A novel flow injection amperometric sensor based on carbon black and graphene oxide modified screen-printed carbon electrode for highly sensitive determination of uric acid

A simple, rapid, and cost-effective flow injection amperometric (FI-Amp) sensor for sensitive determination of uric acid (UA) was developed based on a new combination of carbon black (CB) and graphene oxide (GO) modified screen-printed carbon electrode (SPCE). The CB-GO nanocomposites were simply synthesized and modified on the working electrode surface to increase electrode conductivity and enhance the sensitivity of UA determination via the electrocatalytic activity toward UA oxidation. The morphologies and electrochemical properties of the synthesized nanomaterials were investigated through scanning electron microscopy (SEM), transmission electron microscopy (TEM), electrochemical impedance spectroscopy (EIS), and cyclic voltammetry (CV). The modified electrode was incorporated with FI-Amp to improve UA detection's sensitivity, stability, and automation. Some parameters affecting sensitivity were optimized, including pH of the electrolyte solution, applied potential, amount of CB-GO suspension, flow rate, injection volume, and reaction coil length. Using an applied potential of +0.35 V (vs Ag/AgCl), the anodic current was linearly proportional to UA concentration over the range of 0.05-2000 μM with a detection limit of 0.01 μM (3 S/N). Besides, the developed method provides a sample throughput of 25 injections h^-1, excellent sensitivity (0.0191 μA/μM), selectivity, repeatability (RSD 3.1%, n = 7), and stability (RSD 1.08%, n = 50). The proposed system can tolerate potential interferences commonly found in human urine. Furthermore, a good correlation coefficient between the results obtained from the FI-Amp sensor and a hospital laboratory implies that the proposed system is accurate and can be utilized for UA detection in urine samples.

Simultaneous Recognition of Dopamine and Uric Acid in the Presence of Ascorbic Acid via an Intercalated MXene/PPy Nanocomposite

Two-dimensional (2D) MXenes have shown a great potential for chemical sensing due to their electric properties. In this work, a Ti₃C₂T_x/polypyrrole (MXene/PPy) nanocomposite has been synthesized and immobilized into a glassy carbon electrode to enable the simultaneous recognition of dopamine (DA) and uric acid (UA) under the interference of ascorbic acid (AA). The multilayer Ti₃C₂T_x MXene was prepared via the aqueous acid etching method and delaminated to a single layer nanosheet, benefiting the in-situ growth of PPy nanowires. The controllable preparation strategy and the compounding of PPy material remain great challenges for further practical application. A facile chemical oxidation method was proposed to regulate magnitude and density during the forming process of PPy nanowire, which promotes the conductivity and the electrochemical active site of this as-prepared nanomaterial. The MXene/PPy nanocomposite-modified electrode exhibited the selective determination of DA and UA in the presence of a high concentration of AA, as well as a wide linear range (DA: 12.5–125 μM, UA: 50–500 μM) and a low detection limit (DA: 0.37 μM, UA: 0.15 μM). More importantly, the simultaneous sensing for the co-existence of DA and UA was successfully achieved via the as-prepared sensor.

Morphology-dependent MnO2/nitrogen-doped graphene nanocomposites for simultaneous detection of trace dopamine and uric acid

Four nanostructured MnO₂ with various controllable morphologies, including nanowires, nanorods, nanotubes and nanoflowers were synthesized, and then further composited with nitrogen-doped graphene (NG) with the assistance of ultrasonication. The surface morphologies, phase structures, and electrochemical performances of the proposed MnO₂/NG nanohybrids were investigated by various techniques, and their catalytic activities on the electrooxidation of dopamine (DA) and uric acid (UA) were compared systematically. The sensing performances were found to be highly correlated with their morphologies. Among these morphologies, the nanoflower-like MnO₂, composited with NG, displayed the most sensitive response signals for DA and UA. The boosted electrocatalytic activity was ascribed to the unique porous structure, large electroactive area, and low charge transfer resistance (R_ct), which facilitated the electron transfer between electrode and analytes. Two linear response ranges (0.1 μM-10 μM and 10 μM-100 μM) were accompanied with very low detection limits of 34 nM and 39 nM for DA and UA, respectively. Moreover, the successful application of the MnO₂NFs/NG composites for the simultaneous detection of DA and UA in human serum was realized using second-derivative linear sweep voltammetry (SDLSV). These findings give valuable insights for understanding the morphology-dependent sensing properties of MnO₂ based nanomaterials, which is conducive to the rapid development of ubiquitous MnO₂-based electrochemical sensors.

Electrochemically Reduced Graphene Oxide-Based Screen-Printed Electrodes for Total Tetracycline Determination by Adsorptive Transfer Stripping Differential Pulse Voltammetry

Disposable electrochemically reduced graphene oxide-based (ERGO) screen-printed electrodes (SPE) were developed for the determination of total tetracyclines as a sample screening approach. To this end, a selective adsorption-detection approach relied on adsorptive transfer stripping differential pulse voltammetry (AdTDPV) was devised, where the high adsorption capacity and the electrochemical properties of ERGO were simultaneously exploited. The approach was very simple, fast (6 min.), highly selective by combining the adsorptive and the electrochemical features of tetracyclines, and it used just 10 μL of the sample. The electrochemical sensor applicability was demonstrated in the analysis of environmental and food samples. The not-fully explored AdTDPV analytical possibilities on disposable nanostructured transducers become a new tool in food and environmental fields; drawing new horizons for “in-situ” analysis.

Carbon Nanotubes Modified With Au for Electrochemical Detection of Prostate Specific Antigen: Effect of Au Nanoparticle Size Distribution

Different functionalized Multi-Wall Carbon Nanotube and gold nanoparticles (AuNPs) were synthesized as biosensor electrodes. These materials have been applied to the detection of the Prostate Specific Antigen (PSA). The synthesis of AuNPs was carried out using polyvinylpyrrolidone (PVP) as protecting agent. The PVP/Au molar ratio (0.5 and 50) controls the nanoparticle size distribution, obtaining a wide and narrow distribution with an average diameter of 9.5 and 6.6 nm, respectively. Nanoparticle size distribution shows an important effect in the electrochemical performance of the biosensor, increasing the electrochemical active surface area (EASA) and promoting the electron-transfer from the redox probe (Ferrocene/Ferrocenium) to the electrode. Furthermore, a narrow and small nanoparticle size distribution enhances the amount of antibodies immobilized on the transducer material and the performance during the detection of the PSA. Significant results were obtained for the quantification of PSA, with a limit of detection of 1 ng·ml⁻¹ and sensitivities of 0.085 and 0.056 μA·mL·ng⁻¹ for the two transducer materials in only 5 min of detection.

Disposable Nonenzymatic Uric Acid and Creatinine Sensors Using μPAD Coupled with Screen-Printed Reduced Graphene Oxide-Gold Nanocomposites

Uric acid (UA) and creatinine are the imperative biological substance for clinical monitoring and diagnosis. Measuring the ratio between uric acid and creatinine in urine helps differentiate acute uric acid nephropathy from the hyperuricemia that secondarily occurs to renal failure. In general, the ratio is greater than 0.9 in acute uric acid nephropathy and less than 0.7 in hyperuricemia. In this work, disposable nonenzymatic screen-printed reduced graphene oxide-gold nanocomposites electrodes were firstly developed for the quantitative analysis of uric acid. Our sensors were also coupled with the paper-based colorimetric sensor of the determination of creatinine. Hence, an alternative high-throughput screening test for the uric acid to creatinine ratio with high sensitivity, specificity, simplicity, and rapidity was developed. Under the optimum conditions, our disposable nonenzymatic screen-printed electrode for the determination of uric acid shows the acceptable analytical performance in a wide range of linearity (2.5-1,000 μM) with a low detection limit of 0.74 μM. Our electrodes also showed no interference from common physiologic compound in urine. The determination of creatinine has been developed using Jaffé reaction between the creatinine and picric acid in alkaline condition. The alkaline picrate color on μPAD changed from yellow to orange in the presence of creatinine and the orange intensity is directly proportional to the creatinine amount in a linearity range of 0.20-6.0 mM as a detection limit of 180 μM. Finally, our device has been utilized to determine uric acid and creatinine simultaneously in control urine samples with acceptable result.

Hierarchical bi-continuous Pt decorated nanoporous Au-Sn alloy on carbon fiber paper for ascorbic acid, dopamine and uric acid simultaneous sensing

In this work, Pt nanoparticles modified nanoporous AuSn(Pt@NP-AuSn) alloy on Ni buffered flexible carbon fiber paper (CFP) is fabricated by a simple replacement reaction in which NP-AuSn is fabricated by controllable dealloy of electrodeposited Au-Sn alloy films. The as prepared Pt@NP-AuSn/Ni/CFP possesses hierarchical pore structure, high specific surface area and excellent catalytic activity. Due to the bi-functions of both the large surface area of nanoporous metal and macroporous of carbon fiber paper facilitating mass transfer, the Pt@NP-AuSn/Ni/CFP shows high sensitivity of detecting ascorbic acid (AA), dopamine (DA) and uric acid (UA), with sensitivities of 0.14 μA μM^-1 cm^-2, 15.23 μA μM^-1 cm^-2, 0.28 μA μM^-1 cm^-2 under the concentration ranging from 200 to 2000 μM, 1-10 μM, and 25-800 μM for AA, DA and UA, respectively. Further, the Pt@NP-AuSn/Ni/CFP possesses long-term stability of sensing AA, DA and UA and presents great anti-interference towards a variety of common compounds in body fluid. All of these results manifest the Pt@NP-AuSn/Ni/CFP can be a promising candidate for the application of the electrochemical sensor for simultaneous detection of AA, DA and UA.

Ruthenium and manganese metalloporphyrins modified screen-printed electrodes for bio-relevant electroactive targets

Ruthenium(II) 5-(4[Formula: see text]-sulfanylmethylphenyl)-10,15,20-triphenylporphyrin (Ru-TPP-SH) and manganese(III) 5-(4[Formula: see text]-sulfanylmethylphenyl)-10,15,20-triphenylporphyrin (Mn-TPP-SH) were synthesized, spectroscopically characterized and drop casted to modify screen-printed electrodes (SPEs). The modified SPEs were then tested against the redox target [Fe(CN)6][Formula: see text] in comparison with the bare SPE and SPE modified with the free porphyrin. The best performing one, [Formula: see text]. Mn-TPP-SH was used for the electrochemical detection of 1,4–benzoquinone, serotonin, caffeic and ascorbic acids, the latter also in association with uric acid, showing good electrocatalytic properties. The tunability of the metal-TPP-SH through the choice of the coordinating metal, the drop casting conditions and possible further functionalization make this type of porphyrin a good candidate for further developments of porphyrin-modified SPEs.