1
|
Kedara Shivasharma T, Mendhe AC, Sahu R, Sankapal BR. "Unveiling marigold assembled micro flowers of tungsten oxide towards solid-state flexible pouch and coin cell supercapacitors". J Colloid Interface Sci 2024; 676:739-754. [PMID: 39059280 DOI: 10.1016/j.jcis.2024.07.148] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 04/30/2024] [Revised: 07/18/2024] [Accepted: 07/18/2024] [Indexed: 07/28/2024]
Abstract
Marigold analogues micro flowers of tungsten oxide (WO3) have been grown in thin film form through simple and cost-effective solution chemistry approach on stainless steel substrate. Aqueous precursor involving WO4-2 ions agglomerated as self-sacrificing template growing initially into the nano-petal, followed by self-assembly; leading to marigold analogues micro flower surface architecture. This enthralling morphology motivated us not only to fabricate supercapacitive electrode but also to design complete solid-state supercapacitor devices in dual configurations: flexible pouch cell and coin cell. Interestingly, both devices even in symmetric configuration yields remarkable potential window of 1.82 V when sandwiched by gel inclusive of Li+ ions dispersed in non-conducting polyvinyl alcohol matrix. Solid-state flexible pouch cell and coin cell delivered specific capacitances of 103.98 ± 3.59 and 30.09 ± 1.03 F/g respectively at a scan rate of 5 mV/s. Assembled electrode, coin-cell and flexible pouch-cells have been well assessed in-depth through specific capacitances using cyclic voltammetry and galvanostatic charge discharge, diffusive and capacitive contributions, mechanical bending tests, electrochemical active surface area, and electrochemical impedance analysis. Practical applicability has been demonstrated for designed flexible pouch cell to run small fan and light emitting diode panel whereas coin cell to run light emitting diode panel.
Collapse
Affiliation(s)
- T Kedara Shivasharma
- Nano Materials and Device Laboratory, Department of Physics, Visvesvaraya National Institute of Technology, South Ambazari Road, Nagpur 440 010, M.S., India
| | - Avinash C Mendhe
- Department of Electronics Engineering, Institute for Wearable Convergence Electronics, Kyung Hee University, Yongin, Republic of Korea
| | - Rajulal Sahu
- Nano Materials and Device Laboratory, Department of Physics, Visvesvaraya National Institute of Technology, South Ambazari Road, Nagpur 440 010, M.S., India
| | - Babasaheb R Sankapal
- Nano Materials and Device Laboratory, Department of Physics, Visvesvaraya National Institute of Technology, South Ambazari Road, Nagpur 440 010, M.S., India.
| |
Collapse
|
2
|
Velmurugan R, Mary AS, Pandikumar A, Murugan P, Subramanian B. Pulsed Laser Ablation of Oxygen deficiency Enriched Superlattice Vanadium Pentoxide (V 2O 5) Ultrathin Nextrode aiming for Flexible Binder-less Tandem Energy Harvesting Devices. SMALL (WEINHEIM AN DER BERGSTRASSE, GERMANY) 2024; 20:e2403531. [PMID: 38874066 DOI: 10.1002/smll.202403531] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Received: 05/01/2024] [Revised: 05/28/2024] [Indexed: 06/15/2024]
Abstract
For the initial instance, oxygen deficiency-enriched vanadium pentoxide (O─V2O5@500) thin film electrodes are tuned by the Pulsed Laser Ablation technique. The O─V2O5@500 thin film electrode shows remarkable electrochemical performances confirming the greater potential window of -0.4 to 0.9 V versus Hg/HgO in an alkaline electrolyte; also, the O─V2O5@ 500 thin film electrode exhibits a noteworthy volumetric capacity of 167.7 mAh cm-3 (areal capacity of 73.3 µAh cm-2). Additionally, Density Functional Theory (DFT) theory calculations are carried out for oxygen-deficient V2O5. From the partial density of states (pDOS) and partial charge density analysis, it is clear that oxygen vacancy improves the electrical conductivity due to the higher degree of electron delocalization of V─O─V near the vacancy and enhances the redox properties due to the formation of in-gap states. Further, it is reported that a O─V2O5@ 500 ||PVA-KOH|| Bi2O3 A-650 thin film supercapbattery (TFSCB) device attains an exceptional discharge volumetric capacitance of 182.85 F cm-3 (equal volumetric capacity of 124.5 mAh cm-3). Furthermore, the TFSCB device exhibits an extraordinary maximum volumetric energy (power) density of 14.28 mWh cm-3 (1.66 W cm-3); TFSCB succeeds in supreme capacity retention of 86% with outstanding coulombic efficiency of 94.4% after 21 000 cycles.
Collapse
Affiliation(s)
- Ramasamy Velmurugan
- CSIR- Central Electrochemical Research Institute, Karaikudi, TN, 630 003, India
- Academy of Scientific and Innovative Research (AcSIR), Ghaziabad, UP, 201002, India
| | - Antonysamy Soundarya Mary
- CSIR- Central Electrochemical Research Institute, Karaikudi, TN, 630 003, India
- Academy of Scientific and Innovative Research (AcSIR), Ghaziabad, UP, 201002, India
| | - Alagarsamy Pandikumar
- CSIR- Central Electrochemical Research Institute, Karaikudi, TN, 630 003, India
- Academy of Scientific and Innovative Research (AcSIR), Ghaziabad, UP, 201002, India
| | - Palanichamy Murugan
- CSIR- Central Electrochemical Research Institute, Karaikudi, TN, 630 003, India
- Academy of Scientific and Innovative Research (AcSIR), Ghaziabad, UP, 201002, India
| | - Balasubramanian Subramanian
- CSIR- Central Electrochemical Research Institute, Karaikudi, TN, 630 003, India
- Academy of Scientific and Innovative Research (AcSIR), Ghaziabad, UP, 201002, India
| |
Collapse
|
3
|
Qorbani M, Chen KH, Chen LC. Hybrid and Asymmetric Supercapacitors: Achieving Balanced Stored Charge across Electrode Materials. SMALL (WEINHEIM AN DER BERGSTRASSE, GERMANY) 2024; 20:e2400558. [PMID: 38570734 DOI: 10.1002/smll.202400558] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Received: 01/24/2024] [Revised: 03/06/2024] [Indexed: 04/05/2024]
Abstract
An electrochemical capacitor configuration extends its operational potential window by leveraging diverse charge storage mechanisms on the positive and negative electrodes. Beyond harnessing capacitive, pseudocapacitive, or Faradaic energy storage mechanisms and enhancing electrochemical performance at high rates, achieving a balance of stored charge across electrodes poses a significant challenge over a wide range of charge-discharge currents or sweep rates. Consequently, fabricating hybrid and asymmetric supercapacitors demands precise electrochemical evaluations of electrode materials and the development of a reliable methodology. This work provides an overview of fundamental aspects related to charge-storage mechanisms and electrochemical methods, aiming to discern the contribution of each process. Subsequently, the electrochemical properties, including the working potential windows, rate capability profiles, and stabilities, of various families of electrode materials are explored. It is then demonstrated, how charge balancing between electrodes falters across a broad range of charge-discharge currents or sweep rates. Finally, a methodology for achieving charge balance in hybrid and asymmetric supercapacitors is proposed, outlining multiple conditions dependent on loaded mass and charge-discharge current. Two step-by-step tutorials and model examples for applying this methodology are also provided. The proposed methodology is anticipated to stimulate continued dialogue among researchers, fostering advancements in achieving stable and high-performance supercapacitor devices.
Collapse
Affiliation(s)
- Mohammad Qorbani
- Center for Condensed Matter Sciences, National Taiwan University, Taipei, 10617, Taiwan
- Center of Atomic Initiative for New Materials, National Taiwan University, Taipei, 10617, Taiwan
| | - Kuei-Hsien Chen
- Center for Condensed Matter Sciences, National Taiwan University, Taipei, 10617, Taiwan
- Institute of Atomic and Molecular Sciences, Academia Sinica, Taipei, 10617, Taiwan
| | - Li-Chyong Chen
- Center for Condensed Matter Sciences, National Taiwan University, Taipei, 10617, Taiwan
- Center of Atomic Initiative for New Materials, National Taiwan University, Taipei, 10617, Taiwan
- Department of Physics, National Taiwan University, Taipei, 10617, Taiwan
| |
Collapse
|
4
|
Ansari MZ, Hussain I, Mohapatra D, Ansari SA, Rahighi R, Nandi DK, Song W, Kim S. Atomic Layer Deposition-A Versatile Toolbox for Designing/Engineering Electrodes for Advanced Supercapacitors. ADVANCED SCIENCE (WEINHEIM, BADEN-WURTTEMBERG, GERMANY) 2024; 11:e2303055. [PMID: 37937382 PMCID: PMC10767429 DOI: 10.1002/advs.202303055] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Received: 05/12/2023] [Revised: 09/07/2023] [Indexed: 11/09/2023]
Abstract
Atomic layer deposition (ALD) has become the most widely used thin-film deposition technique in various fields due to its unique advantages, such as self-terminating growth, precise thickness control, and excellent deposition quality. In the energy storage domain, ALD has shown great potential for supercapacitors (SCs) by enabling the construction and surface engineering of novel electrode materials. This review aims to present a comprehensive outlook on the development, achievements, and design of advanced electrodes involving the application of ALD for realizing high-performance SCs to date, as organized in several sections of this paper. Specifically, this review focuses on understanding the influence of ALD parameters on the electrochemical performance and discusses the ALD of nanostructured electrochemically active electrode materials on various templates for SCs. It examines the influence of ALD parameters on electrochemical performance and highlights ALD's role in passivating electrodes and creating 3D nanoarchitectures. The relationship between synthesis procedures and SC properties is analyzed to guide future research in preparing materials for various applications. Finally, it is concluded by suggesting the directions and scope of future research and development to further leverage the unique advantages of ALD for fabricating new materials and harness the unexplored opportunities in the fabrication of advanced-generation SCs.
Collapse
Affiliation(s)
- Mohd Zahid Ansari
- School of Materials Science and EngineeringYeungnam University280 Daehak‐RoGyeongsanGyeongbuk38541Republic of Korea
| | - Iftikhar Hussain
- Department of Mechanical EngineeringCity University of Hong Kong83 Tat Chee AvenueKowoonHong Kong
| | - Debananda Mohapatra
- Graduate School of Semiconductor Materials and Devices EngineeringUlsan National Institute of Science & Technology (UNIST)50 UNIST‐gilUlju‐gunUlsan44919Republic of Korea
| | - Sajid Ali Ansari
- Department of PhysicsCollege of ScienceKing Faisal UniversityP.O. Box 400HofufAl‐Ahsa31982Saudi Arabia
| | - Reza Rahighi
- SKKU Advanced Institute of Nano‐Technology (SAINT)Sungkyunkwan University2066 Seobu‐ro, Jangan‐guSuwonGyeonggi‐do16419Republic of Korea
| | - Dip K Nandi
- Plessey Semiconductors LtdTamerton Road RoboroughPlymouthDevonPL6 7BQUK
| | - Wooseok Song
- Thin Film Materials Research CenterKorea Research Institute of Chemical TechnologyDaejeon34114Republic of Korea
| | - Soo‐Hyun Kim
- Graduate School of Semiconductor Materials and Devices EngineeringUlsan National Institute of Science & Technology (UNIST)50 UNIST‐gilUlju‐gunUlsan44919Republic of Korea
- Department of Materials Science and EngineeringUlsan National Institute of Science & Technology (UNIST)50 UNIST‐gilUlju‐gunUlsan44919Republic of Korea
| |
Collapse
|
5
|
ALD-fabricated two-dimensional SnO2-In2O3 n-n nanohybrid electrode for electrochemical supercapacitors. Electrochim Acta 2022. [DOI: 10.1016/j.electacta.2022.141322] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/18/2022]
|
6
|
Mineo G, Scuderi M, Pezzotti Escobar G, Mirabella S, Bruno E. Engineering of Nanostructured WO 3 Powders for Asymmetric Supercapacitors. NANOMATERIALS (BASEL, SWITZERLAND) 2022; 12:nano12234168. [PMID: 36500791 PMCID: PMC9738873 DOI: 10.3390/nano12234168] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.3] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Received: 10/20/2022] [Revised: 11/17/2022] [Accepted: 11/22/2022] [Indexed: 06/02/2023]
Abstract
Transition metal oxide nanostructures are promising materials for energy storage devices, exploiting electrochemical reactions at nanometer solid-liquid interface. Herein, WO3 nanorods and hierarchical urchin-like nanostructures were obtained by hydrothermal method and calcination processes. The morphology and crystal phase of WO3 nanostructures were investigated by scanning and transmission electron microscopy (SEM and TEM) and X-ray diffraction (XRD), while energy storage performances of WO3 nanostructures-based electrodes were evaluated by cyclic voltammetry (CV) and galvanostatic charge-discharge (GCD) tests. Promising values of specific capacitance (632 F/g at 5 mV/s and 466 F/g at 0.5 A/g) are obtained when pure hexagonal crystal phase WO3 hierarchical urchin-like nanostructures are used. A detailed modeling is given of surface and diffusion-controlled mechanisms in the energy storage process. An asymmetric supercapacitor has also been realized by using WO3 urchin-like nanostructures and a graphene paper electrode, revealing the highest energy density (90 W × h/kg) at a power density of 90 W × kg-1 and the highest power density (9000 W/kg) at an energy density of 18 W × h/kg. The presented correlation among physical features and electrochemical performances of WO3 nanostructures provides a solid base for further developing energy storage devices based on transition metal oxides.
Collapse
Affiliation(s)
- Giacometta Mineo
- Physics and Astronomy Department “Ettore Majorana”, University of Study of Catania, via S. Sofia 64, 95123 Catania, Italy
- CNR—Institute for Microsystems and Microelectronics, Catania University Unit, via S. Sofia 64, 95123 Catania, Italy
| | - Mario Scuderi
- CNR—Institute for Microsystems and Microelectronics, Strada VIII 5, 95121 Catania, Italy
| | - Gianni Pezzotti Escobar
- CNR—Institute for Microsystems and Microelectronics, Catania University Unit, via S. Sofia 64, 95123 Catania, Italy
| | - Salvo Mirabella
- Physics and Astronomy Department “Ettore Majorana”, University of Study of Catania, via S. Sofia 64, 95123 Catania, Italy
- CNR—Institute for Microsystems and Microelectronics, Catania University Unit, via S. Sofia 64, 95123 Catania, Italy
| | - Elena Bruno
- Physics and Astronomy Department “Ettore Majorana”, University of Study of Catania, via S. Sofia 64, 95123 Catania, Italy
- CNR—Institute for Microsystems and Microelectronics, Catania University Unit, via S. Sofia 64, 95123 Catania, Italy
| |
Collapse
|
7
|
Le PA, Le VQ, Tran TL, Nguyen NT, Phung TVB. Computation and Investigation of Two-Dimensional WO 3·H 2O Nanoflowers for Electrochemical Studies of Energy Conversion and Storage Applications. ACS OMEGA 2022; 7:10115-10126. [PMID: 35382300 PMCID: PMC8973110 DOI: 10.1021/acsomega.1c06150] [Citation(s) in RCA: 2] [Impact Index Per Article: 0.7] [Reference Citation Analysis] [Abstract] [Grants] [Track Full Text] [Download PDF] [Figures] [Subscribe] [Scholar Register] [Received: 11/02/2021] [Accepted: 03/03/2022] [Indexed: 06/14/2023]
Abstract
The aim of this study is to prepare a two-dimensional (2D) WO3·H2O nanostructure assembly into a flower shape with good chemical stability for electrochemical studies of catalyst and energy storage applications. The 2D-WO3·H2O nanoflowers structure is created by a fast and simple process at room condition. This cost-effective and scalable technique to obtain 2D-WO3·H2O nanoflowers illustrates two attractive applications of electrochemical capacitor with an excellent energy density value of 25.33 W h kg-1 for high power density value of 1600 W kg-1 and good hydrogen evolution reaction results (low overpotential of 290 mV at a current density of 10 mA cm-2 with a low Tafel slope of 131 mV dec-1). A hydrogen evolution reaction (HER) study of WO3 in acidic media of 0.5 M H2SO4 and electrochemical capacitor (supercapacitors) in 1 M Na2SO4 aqueous electrolyte (three electrode system measurements) demonstrates highly desirable characteristics for practical applications. Our design for highly uniform 2D-WO3·H2O as catalyst material for HER and active material for electrochemical capacitor studies offers an excellent foundation for design and improvement of electrochemical catalyst based on 2D-transition metal oxide materials.
Collapse
Affiliation(s)
- Phuoc Anh Le
- Institute
of Sustainability Science, VNU Vietnam Japan University, Vietnam National University, Hanoi 100000, Vietnam
| | - Van Qui Le
- Department
of Materials Science and Engineering, National
Yang Ming Chiao Tung University, Hsinchu 300093, Taiwan
| | - Thien Lan Tran
- Institute
of Sustainability Science, VNU Vietnam Japan University, Vietnam National University, Hanoi 100000, Vietnam
- Department
of Physics, Hue University of Education, Hue University, 34 Le
Loi Stress, Hue 530000, Vietnam
| | - Nghia Trong Nguyen
- School
of Chemical Engineering, Hanoi University
of Science and Technology, Hanoi 100000, Vietnam
| | - Thi Viet Bac Phung
- Institute
of Sustainability Science, VNU Vietnam Japan University, Vietnam National University, Hanoi 100000, Vietnam
| |
Collapse
|
8
|
Pirker L, Višić B. Recent Progress in the Synthesis and Potential Applications of Two‐Dimensional Tungsten (Sub)oxides. Isr J Chem 2021. [DOI: 10.1002/ijch.202100074] [Citation(s) in RCA: 2] [Impact Index Per Article: 0.5] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/10/2022]
Affiliation(s)
- Luka Pirker
- Solid State Physics Jozef Stefan Institute Jamova cesta 39 1000 Ljubljana Slovenia
| | - Bojana Višić
- Solid State Physics Jozef Stefan Institute Jamova cesta 39 1000 Ljubljana Slovenia
- Institute of Physics Belgrade University of Belgrade Pregrevica 118 11080 Belgrade Serbia
| |
Collapse
|
9
|
Shi F, Li J, Xiao J, Zhao X, Li H, An Q, Zhai S, Wang K, Wei L, Tong Y. Three-dimensional hierarchical porous lignin-derived carbon/WO 3 for high-performance solid-state planar micro-supercapacitor. Int J Biol Macromol 2021; 190:11-18. [PMID: 34478791 DOI: 10.1016/j.ijbiomac.2021.08.183] [Citation(s) in RCA: 9] [Impact Index Per Article: 2.3] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 07/09/2021] [Revised: 08/21/2021] [Accepted: 08/25/2021] [Indexed: 10/20/2022]
Abstract
The development of advanced energy storage systems, such as rechargeable batteries and supercapacitors (SCs), is one of the great challenges related to energy demand with the rapid development of world economy. Herein, a three-dimensional hierarchical porous lignin-derived carbon/WO3 (HPC/WO3) was prepared by carbonization and solvothermal process. This electrode material for supercapacitor can be operated at a wide voltage window range of -0.4 V to 1.0 V. More importantly, 3HPC/WO3 with ultrahigh mass loading (~3.56 mg cm-2) has excellent specific capacitance of 432 F g-1 at 0.5 A g-1 and cycling stability of 86.6% after 10,000 cycles at 10 A g-1. The as-assembled asymmetrical supercapacitor shows an energy density of 34.2 W h kg-1 at a power density of 237 W kg-1 and energy density of 16 W h kg-1 at a power density is 14,300 W kg-1. A solid-state planar micro-supercapacitor (MSC) was fabricated using HPC/WO3 nanocomposites. Moreover, the calculated specific capacity of MSC was 20 mF cm-2 in polyvinyl alcohol-sulfuric acid gel electrolyte. Overall, through the reasonable design of HPC/WO3 nanocomposite materials and the efficient assembly of MSCs, the performance of the device was greatly improved, thus providing a clear strategy for the development of energy storage devices.
Collapse
Affiliation(s)
- Feiyan Shi
- Faculty of Light Industry and Chemical Engineering, Dalian Polytechnic University, Dalian 116034, Liaoning, China
| | - Jiajun Li
- Faculty of Light Industry and Chemical Engineering, Dalian Polytechnic University, Dalian 116034, Liaoning, China
| | - Jiatong Xiao
- Faculty of Light Industry and Chemical Engineering, Dalian Polytechnic University, Dalian 116034, Liaoning, China
| | - Xinyu Zhao
- Faculty of Light Industry and Chemical Engineering, Dalian Polytechnic University, Dalian 116034, Liaoning, China
| | - Hongsheng Li
- Faculty of Light Industry and Chemical Engineering, Dalian Polytechnic University, Dalian 116034, Liaoning, China
| | - Qingda An
- Faculty of Light Industry and Chemical Engineering, Dalian Polytechnic University, Dalian 116034, Liaoning, China.
| | - Shangru Zhai
- Faculty of Light Industry and Chemical Engineering, Dalian Polytechnic University, Dalian 116034, Liaoning, China
| | - Kai Wang
- Dalian National Laboratory for Clean Energy, Dalian Institute of Chemical Physics, Chinese Academy of Sciences, Dalian 116023, China.
| | - Li Wei
- Faculty of Light Industry and Chemical Engineering, Dalian Polytechnic University, Dalian 116034, Liaoning, China.
| | - Yao Tong
- Faculty of Light Industry and Chemical Engineering, Dalian Polytechnic University, Dalian 116034, Liaoning, China.
| |
Collapse
|
10
|
Zhao S, Dong C, Huang F. Proton-insertion-pseudocapacitance of tungsten bronze tunnel structure enhanced by transition metal ion anchoring. NANOSCALE 2021; 13:16790-16798. [PMID: 34605519 DOI: 10.1039/d1nr02384e] [Citation(s) in RCA: 4] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/13/2023]
Abstract
The one-dimensional channel array of hexagonal tungsten bronze (WO3) offers an electron transfer matrix, but its overwhelming H+ adsorption hinders it from being a good supercapacitor electrode material. Inspired by the Volcano plot on the relation between transition-metal and free energy of H-adsorption, we propose a new strategy to anchor transition metal ions (Zn2+, Cu2+, Ni2+, Ag+, Au3+ and Ir3+) into the WO3 lattice to improve proton-insertion based pseudocapacitance. Among the variety of transition metals, Zn2+ exhibits the optimal O 2p band center, which matches well with the best experimental capacitive behavior. The molar ratio of Zn/WO3 ranges from 0.2 to 0.6. The specific capacitance for Zn2+-anchored WO3 (390 F g-1) reaches 202% of that of WO3 (193 F g-1) at 0.5 A g-1 with robust stability (259 F g-1 at 3 A g-1 for 3000 cycles). Density functional theory confirms that O 2p is shifted down by the d-filling cations, which corresponds to alleviated O-H interaction and facilitated H+ desorption. The band tuning by transition-metal-ion incorporation would break new ground on developing high-capacitance metal oxide supercapacitors.
Collapse
Affiliation(s)
- Siwei Zhao
- Beijing National Laboratory for Molecular Sciences and State Key Laboratory of Rare Earth Materials Chemistry and Applications, College of Chemistry and Molecular Engineering, Peking University, Beijing 100871, P.R. China.
| | - Chenlong Dong
- Beijing National Laboratory for Molecular Sciences and State Key Laboratory of Rare Earth Materials Chemistry and Applications, College of Chemistry and Molecular Engineering, Peking University, Beijing 100871, P.R. China.
| | - Fuqiang Huang
- Beijing National Laboratory for Molecular Sciences and State Key Laboratory of Rare Earth Materials Chemistry and Applications, College of Chemistry and Molecular Engineering, Peking University, Beijing 100871, P.R. China.
- State Key Laboratory of High-Performance Ceramics and Superfine Microstructure, Shanghai Institute of Ceramics, Chinese Academy of Sciences, Shanghai 200050, P.R. China
| |
Collapse
|
11
|
Xu H, Akbari MK, Zhuiykov S. 2D Semiconductor Nanomaterials and Heterostructures: Controlled Synthesis and Functional Applications. NANOSCALE RESEARCH LETTERS 2021; 16:94. [PMID: 34032946 PMCID: PMC8149775 DOI: 10.1186/s11671-021-03551-w] [Citation(s) in RCA: 8] [Impact Index Per Article: 2.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Received: 04/12/2021] [Accepted: 05/17/2021] [Indexed: 06/01/2023]
Abstract
Two-dimensional (2D) semiconductors beyond graphene represent the thinnest stable known nanomaterials. Rapid growth of their family and applications during the last decade of the twenty-first century have brought unprecedented opportunities to the advanced nano- and opto-electronic technologies. In this article, we review the latest progress in findings on the developed 2D nanomaterials. Advanced synthesis techniques of these 2D nanomaterials and heterostructures were summarized and their novel applications were discussed. The fabrication techniques include the state-of-the-art developments of the vapor-phase-based deposition methods and novel van der Waals (vdW) exfoliation approaches for fabrication both amorphous and crystalline 2D nanomaterials with a particular focus on the chemical vapor deposition (CVD), atomic layer deposition (ALD) of 2D semiconductors and their heterostructures as well as on vdW exfoliation of 2D surface oxide films of liquid metals.
Collapse
Affiliation(s)
- Hongyan Xu
- School of Materials Science and Engineering, North University of China, Taiyuan, 030051 People’s Republic of China
| | - Mohammad Karbalaei Akbari
- Centre for Environmental and Energy Research, Ghent University Global Campus, 119-5 Songdomunhwa-ro, Yeonsu-gu, Incheon, 21985 South Korea
- Department of Solid State Science, Faculty of Science, Ghent University, Krijgslaan 281/S1, 9000 Ghent, Belgium
| | - Serge Zhuiykov
- School of Materials Science and Engineering, North University of China, Taiyuan, 030051 People’s Republic of China
- Centre for Environmental and Energy Research, Ghent University Global Campus, 119-5 Songdomunhwa-ro, Yeonsu-gu, Incheon, 21985 South Korea
- Department of Solid State Science, Faculty of Science, Ghent University, Krijgslaan 281/S1, 9000 Ghent, Belgium
| |
Collapse
|
12
|
Zhao Y, Zhang L, Liu J, Adair K, Zhao F, Sun Y, Wu T, Bi X, Amine K, Lu J, Sun X. Atomic/molecular layer deposition for energy storage and conversion. Chem Soc Rev 2021; 50:3889-3956. [PMID: 33523063 DOI: 10.1039/d0cs00156b] [Citation(s) in RCA: 53] [Impact Index Per Article: 13.3] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 01/13/2023]
Abstract
Energy storage and conversion systems, including batteries, supercapacitors, fuel cells, solar cells, and photoelectrochemical water splitting, have played vital roles in the reduction of fossil fuel usage, addressing environmental issues and the development of electric vehicles. The fabrication and surface/interface engineering of electrode materials with refined structures are indispensable for achieving optimal performances for the different energy-related devices. Atomic layer deposition (ALD) and molecular layer deposition (MLD) techniques, the gas-phase thin film deposition processes with self-limiting and saturated surface reactions, have emerged as powerful techniques for surface and interface engineering in energy-related devices due to their exceptional capability of precise thickness control, excellent uniformity and conformity, tunable composition and relatively low deposition temperature. In the past few decades, ALD and MLD have been intensively studied for energy storage and conversion applications with remarkable progress. In this review, we give a comprehensive summary of the development and achievements of ALD and MLD and their applications for energy storage and conversion, including batteries, supercapacitors, fuel cells, solar cells, and photoelectrochemical water splitting. Moreover, the fundamental understanding of the mechanisms involved in different devices will be deeply reviewed. Furthermore, the large-scale potential of ALD and MLD techniques is discussed and predicted. Finally, we will provide insightful perspectives on future directions for new material design by ALD and MLD and untapped opportunities in energy storage and conversion.
Collapse
Affiliation(s)
- Yang Zhao
- Department of Mechanical & Materials Engineering, University of Western Ontario, London, ON N6A 5B9, Canada.
| | | | | | | | | | | | | | | | | | | | | |
Collapse
|
13
|
Sivaprakash P, Kumar KA, Muthukumaran S, Pandurangan A, Dixit A, Arumugam S. NiF2 as an efficient electrode material with high window potential of 1.8 V for high energy and power density asymmetric supercapacitor. J Electroanal Chem (Lausanne) 2020. [DOI: 10.1016/j.jelechem.2020.114379] [Citation(s) in RCA: 14] [Impact Index Per Article: 2.8] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/26/2022]
|
14
|
Tao K, Wang L, Hai Y, Gong Y. P-Functionalized and O-deficient TiO n/VO m nanoparticles grown on Ni foam as an electrode for supercapacitors: epitaxial grown heterojunction and visible-light-driven photoresponse. Dalton Trans 2020; 49:4476-4490. [PMID: 32191247 DOI: 10.1039/d0dt00317d] [Citation(s) in RCA: 2] [Impact Index Per Article: 0.4] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 01/08/2023]
Abstract
P-TiOn-VOm nanowires were grown on nickel foam (NF) via a one-pot hydrothermal method and by further vapor deposition/phosphorization method. It was found that low valence states of titanium oxide and deficient-oxygen coexist in P-TiOn-VOm/NF. Furthermore, (TiO1.25)3.07 (denoted as TiOn) and VO (denoted as VOm) possess similar structures and matched facets, and their epitaxial growth leads to the formation of TiOn/VOm heterostructure with a formation energy of -1.59 eV. P-TiOn-VOm/NF possesses good electron conductivity and electrons can be transferred from Ti to V centers, as evidenced by the DFT calculations and the XPS spectra. As a result, the specific capacity of P-TiOn-VOm/NF can reach 785 C g-1 at 1 A g-1 in the potential range of 0-0.55 V vs. Hg/HgO, which is much larger than those of VOm/NF, P-VOm/NF, and P-TiO2-VOm/NF. On the other hand, the TiOn/VOm heterostructure also favors the separation and transfer of photoinduced electrons and holes, and P-TiOn-VOm/NF exhibits visible-light-driven photoresponse. Under visible light illumination, the specific capacity of P-TiOn-VOm/NF is increased by 6.2% relative to that in the dark. Furthermore, the P-TiOn-VOm/NF//activated carbon (AC) asymmetric supercapacitor (ASC) shows an energy density of 37.2 W h kg-1 at a power density of 1 kW kg-1 and excellent cycling performance with 93.6% capacity retention after 10 000 cycles at 5 A g-1, which is comparable to and even superior to those of titanium oxides and vanadium oxides. A promising achievement has been proposed to improve the energy storage performance of P-TiOn-VOm through P-functionalization and O-deficiency in this work.
Collapse
Affiliation(s)
- Keyu Tao
- Department of Applied Chemistry, College of Chemistry and Chemical Engineering, Chongqing University, Chongqing 401331, P. R. China.
| | - Lian Wang
- Department of Applied Chemistry, College of Chemistry and Chemical Engineering, Chongqing University, Chongqing 401331, P. R. China.
| | - Yang Hai
- Department of Applied Chemistry, College of Chemistry and Chemical Engineering, Chongqing University, Chongqing 401331, P. R. China.
| | - Yun Gong
- Department of Applied Chemistry, College of Chemistry and Chemical Engineering, Chongqing University, Chongqing 401331, P. R. China.
| |
Collapse
|
15
|
Shinde PA, Jun SC. Review on Recent Progress in the Development of Tungsten Oxide Based Electrodes for Electrochemical Energy Storage. CHEMSUSCHEM 2020; 13:11-38. [PMID: 31605458 DOI: 10.1002/cssc.201902071] [Citation(s) in RCA: 36] [Impact Index Per Article: 7.2] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Received: 07/30/2019] [Revised: 09/04/2019] [Indexed: 06/10/2023]
Abstract
Current progress in the advancement of energy-storage devices is the most important factor that will allow the scientific community to develop resources to meet the global energy demands of the 21st century. Nanostructured materials can be used as effective electrodes for energy-storage devices because they offer various promising features, including high surface-to-volume ratios, exceptional charge-transport features, and good physicochemical properties. Until now, the successful research frontrunners have focused on the preparation of positive electrode materials for energy-storage applications; nevertheless, the electrochemical performance of negative electrodes is less frequently reported. This review mainly focuses on the current progress in the development of tungsten oxide-based electrodes for energy-storage applications, primarily supercapacitors (SCs) and batteries. Tungsten is found in various stoichiometric and nonstoichiometric oxides. Among the different tungsten oxide materials, tungsten trioxide (WO3 ) has been intensively investigated as an electrode material for different applications because of its excellent charge-transport features, unique physicochemical properties, and good resistance to corrosion. Various WO3 composites, such as WO3 /carbon, WO3 /polymers, WO3 /metal oxides, and tungsten-based binary metal oxides, have been used for application in SCs and batteries. However, pristine WO3 suffers from a relatively low specific surface area and low energy density. Therefore, it is crucial to thoroughly summarize recent progress in utilizing WO3 -based materials from various perspectives to enhance their performance. Herein, the potential- and pH-dependent behavior of tungsten in aqueous media is discussed. Recent progress in the advancement of nanostructured WO3 and tungsten oxide-based composites, along with related charge-storage mechanisms and their electrochemical performances in SCs and batteries, is systematically summarized. Finally, remarks are made on future research challenges and the prospect of using tungsten oxide-based materials to further upgrade energy-storage devices.
Collapse
Affiliation(s)
- Pragati A Shinde
- Nano-Electro Mechanical Device Laboratory, School of Mechanical Engineering, Yonsei University, Seoul, 120-749, South Korea
| | - Seong Chan Jun
- Nano-Electro Mechanical Device Laboratory, School of Mechanical Engineering, Yonsei University, Seoul, 120-749, South Korea
| |
Collapse
|
16
|
Electrochemical properties of PEDOT/WO3 composite films for high performance supercapacitor application. Electrochim Acta 2019. [DOI: 10.1016/j.electacta.2019.01.007] [Citation(s) in RCA: 36] [Impact Index Per Article: 6.0] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/21/2022]
|
17
|
Wei Z, Hai Z, Akbari MK, Zhao Z, Sun Y, Hyde L, Verpoort F, Hu J, Zhuiykov S. Surface functionalization of wafer-scale two-dimensional WO3 nanofilms by NM electrodeposition (NM = Ag, Pt, Pd) for electrochemical H2O2 reduction improvement. Electrochim Acta 2019. [DOI: 10.1016/j.electacta.2018.12.032] [Citation(s) in RCA: 15] [Impact Index Per Article: 2.5] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 01/03/2023]
|
18
|
Zhu B, Wu X, Liu WJ, Lu HL, Zhang DW, Fan Z, Ding SJ. High-Performance On-Chip Supercapacitors Based on Mesoporous Silicon Coated with Ultrathin Atomic Layer-Deposited In 2O 3 Films. ACS APPLIED MATERIALS & INTERFACES 2019; 11:747-752. [PMID: 30525419 DOI: 10.1021/acsami.8b17093] [Citation(s) in RCA: 3] [Impact Index Per Article: 0.5] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/09/2023]
Abstract
On-chip supercapacitors have attracted considerable attention because of their high power density, long cycling life, and compatibility with integrated circuits. One critical drawback that restricts their practical application is the low energy density. In this work, low-resistivity mesoporous silicon with a high aspect ratio is prepared by Pt film-assisted chemical etching and utilized as the scaffold of the supercapacitors. Subsequently, low-resistivity (<0.0015 Ω·cm) and ultrathin In2O3 films are coated on the mesoporous silicon scaffold by atomic layer deposition at 200 °C, serving as the active electrode material. The electrochemical measurements reveal that the coating of the In2O3 film remarkably improves the performance of the supercapacitors compared with those without the In2O3 coating. The supercapacitors with a 4.5 nm In2O3 film coating exhibit a capacitance density of 1.36 mF/cm2 at a scan rate of 10 mV/s as well as a better stability against the scan rate. In addition, it is found that the pristine mesoporous silicon walls are collapsed after 400 times of sweeping while those with the In2O3 film coating are still intact even after 2000 times of sweeping. Meanwhile, a high energy density is also achieved without sacrificing the power performance.
Collapse
|
19
|
Cao K, Hu Q, Cai J, Gong M, Yang J, Shan B, Chen R. Development of a scanning probe microscopy integrated atomic layer deposition system for in situ successive monitoring of thin film growth. THE REVIEW OF SCIENTIFIC INSTRUMENTS 2018; 89:123702. [PMID: 30599563 DOI: 10.1063/1.5042463] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.1] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Received: 06/01/2018] [Accepted: 11/12/2018] [Indexed: 06/09/2023]
Abstract
A dual chamber system integrated with atomic layer deposition (ALD) and atomic force microscopy (AFM) was developed for the successive monitoring of nanoparticles to thin film growth process. The samples were fabricated in the ALD chamber. A magnetic transmission rod enabled sample transferring between the ALD and the AFM test chambers without breaking the vacuum, avoiding possible surface morphology change when frequently varying the growth condition and oxidation under ambient condition. The sample transmission also avoids deposition and contamination on the AFM tip during the successive testing. The sample stage has machined a group of accurate location pinholes, ensuring the 10 μm2 measurement consistency. As a demonstration, the platinum thin films with different thickness were fabricated by varying ALD cycles. The surface morphology was monitored successively during the deposition. Under vacuum with controlled oxygen partial pressure, the aging and sintering phenomenon of particles has been studied in the AFM testing chamber after high temperature treatment. The integrated AFM/ALD instrument is potentially a powerful system for monitoring the thin film preparation and characterization.
Collapse
Affiliation(s)
- Kun Cao
- State Key Laboratory of Digital Manufacturing Equipment and Technology, School of Mechanical Science and Engineering, Huazhong University of Science and Technology, 1037 Luoyu Road, Wuhan, Hubei 430074, People's Republic of China
| | - Quan Hu
- State Key Laboratory of Material Processing and Die and Mould Technology, School of Materials Science and Engineering, Huazhong University of Science and Technology, 1037 Luoyu Road, Wuhan, Hubei 430074, People's Republic of China
| | - Jiaming Cai
- State Key Laboratory of Digital Manufacturing Equipment and Technology, School of Mechanical Science and Engineering, Huazhong University of Science and Technology, 1037 Luoyu Road, Wuhan, Hubei 430074, People's Republic of China
| | - Miao Gong
- State Key Laboratory of Digital Manufacturing Equipment and Technology, School of Mechanical Science and Engineering, Huazhong University of Science and Technology, 1037 Luoyu Road, Wuhan, Hubei 430074, People's Republic of China
| | - Jianfeng Yang
- State Key Laboratory of Material Processing and Die and Mould Technology, School of Materials Science and Engineering, Huazhong University of Science and Technology, 1037 Luoyu Road, Wuhan, Hubei 430074, People's Republic of China
| | - Bin Shan
- State Key Laboratory of Material Processing and Die and Mould Technology, School of Materials Science and Engineering, Huazhong University of Science and Technology, 1037 Luoyu Road, Wuhan, Hubei 430074, People's Republic of China
| | - Rong Chen
- State Key Laboratory of Digital Manufacturing Equipment and Technology, School of Mechanical Science and Engineering, Huazhong University of Science and Technology, 1037 Luoyu Road, Wuhan, Hubei 430074, People's Republic of China
| |
Collapse
|
20
|
Hai Z, Karbalaei Akbari M, Wei Z, Cui D, Xue C, Xu H, Heynderickx PM, Verpoort F, Zhuiykov S. Nanostructure-induced performance degradation of WO 3· nH 2O for energy conversion and storage devices. BEILSTEIN JOURNAL OF NANOTECHNOLOGY 2018; 9:2845-2854. [PMID: 30498656 PMCID: PMC6244177 DOI: 10.3762/bjnano.9.265] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Figures] [Subscribe] [Scholar Register] [Received: 09/03/2018] [Accepted: 10/26/2018] [Indexed: 06/09/2023]
Abstract
Although 2D layered nanomaterials have been intensively investigated towards their application in energy conversion and storage devices, their disadvantages have rarely been explored so far especially compared to their 3D counterparts. Herein, WO3·nH2O (n = 0, 1, 2), as the most common and important electrochemical and electrochromic active nanomaterial, is synthesized in 3D and 2D structures through a facile hydrothermal method, and the disadvantages of the corresponding 2D structures are examined. The weakness of 2D WO3·nH2O originates from its layered structure. X-ray diffraction and scanning electron microscopy analyses of as-grown WO3·nH2O samples suggest a structural transition from 2D to 3D upon temperature increase. 2D WO3·nH2O easily generates structural instabilities by 2D intercalation, resulting in a faster performance degradation, due to its weak interlayer van der Waals forces, even though it outranks the 3D network structure in terms of improved electronic properties. The structural transformation of 2D layered WO3·nH2O into 3D nanostructures is observed via ex situ Raman measurements under electrochemical cycling experiments. The proposed degradation mechanism is confirmed by the morphology changes. The work provides strong evidence for and in-depth understanding of the weakness of 2D layered nanomaterials and paves the way for further interlayer reinforcement, especially for 2D layered transition metal oxides.
Collapse
Affiliation(s)
- Zhenyin Hai
- Center for Environmental and Energy Research, Ghent University Global Campus, Yeonsu-gu, Incheon 21985, South Korea
- Department of Green Chemistry and Technology, Faculty of Bioscience Engineering, Ghent University, Coupure Links 653, 9000 Ghent, Belgium
| | - Mohammad Karbalaei Akbari
- Center for Environmental and Energy Research, Ghent University Global Campus, Yeonsu-gu, Incheon 21985, South Korea
- Department of Green Chemistry and Technology, Faculty of Bioscience Engineering, Ghent University, Coupure Links 653, 9000 Ghent, Belgium
| | - Zihan Wei
- Center for Environmental and Energy Research, Ghent University Global Campus, Yeonsu-gu, Incheon 21985, South Korea
- Department of Green Chemistry and Technology, Faculty of Bioscience Engineering, Ghent University, Coupure Links 653, 9000 Ghent, Belgium
| | - Danfeng Cui
- Science and Technology on Electronic Test and Measurement Laboratory, North University of China, Taiyuan, Shanxi 030051, P.R. China
| | - Chenyang Xue
- Science and Technology on Electronic Test and Measurement Laboratory, North University of China, Taiyuan, Shanxi 030051, P.R. China
| | - Hongyan Xu
- School of Materials Science and Engineering, North University of China, Shanxi 030051, P.R. China
| | - Philippe M Heynderickx
- Center for Environmental and Energy Research, Ghent University Global Campus, Yeonsu-gu, Incheon 21985, South Korea
- Department of Green Chemistry and Technology, Faculty of Bioscience Engineering, Ghent University, Coupure Links 653, 9000 Ghent, Belgium
| | - Francis Verpoort
- Center for Environmental and Energy Research, Ghent University Global Campus, Yeonsu-gu, Incheon 21985, South Korea
- National Research Tomsk Polytechnic University, Lenin Avenue 30, Tomsk 634050, Russian Federation
- Laboratory of Organometallics, Catalysis and Ordered Materials, State Key Laboratory of Advanced Technology for Materials Synthesis and Processing, Center for Chemical and Material Engineering, Wuhan University of Technology, Wuhan, P.R. China
| | - Serge Zhuiykov
- Center for Environmental and Energy Research, Ghent University Global Campus, Yeonsu-gu, Incheon 21985, South Korea
- Department of Green Chemistry and Technology, Faculty of Bioscience Engineering, Ghent University, Coupure Links 653, 9000 Ghent, Belgium
| |
Collapse
|
21
|
Karbalaei Akbari M, Hai Z, Wei Z, Detavernier C, Solano E, Verpoort F, Zhuiykov S. ALD-Developed Plasmonic Two-Dimensional Au-WO 3-TiO 2 Heterojunction Architectonics for Design of Photovoltaic Devices. ACS APPLIED MATERIALS & INTERFACES 2018; 10:10304-10314. [PMID: 29509409 DOI: 10.1021/acsami.7b17508] [Citation(s) in RCA: 8] [Impact Index Per Article: 1.1] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/08/2023]
Abstract
Electrically responsive plasmonic devices, which benefit from the privilege of surface plasmon excited hot carries, have supported fascinating applications in the visible-light-assisted technologies. The properties of plasmonic devices can be tuned by controlling charge transfer. It can be attained by intentional architecturing of the metal-semiconductor (MS) interfaces. In this study, the wafer-scaled fabrication of two-dimensional (2D) TiO2 semiconductors on the granular Au metal substrate is achieved using the atomic layer deposition (ALD) technique. The ALD-developed 2D MS heterojunctions exhibited substantial enhancement of the photoresponsivity and demonstrated the improvement of response time for 2D Au-TiO2-based plasmonic devices under visible light illumination. To circumvent the undesired dark current in the plasmonic devices, a 2D WO3 nanofilm (∼0.7 nm) was employed as the intermediate layer on the MS interface to develop the metal-insulator-semiconductor (MIS) 2D heterostructure. As a result, 13.4% improvement of the external quantum efficiency was obtained for fabricated 2D Au-WO3-TiO2 heterojunctions. The impedancometry measurements confirmed the modulation of charge transfer at the 2D MS interface using MIS architectonics. Broadband photoresponsivity from the UV to the visible light region was observed for Au-TiO2 and Au-WO3-TiO2 heterostructures, whereas near-infrared responsivity was not observed. Consequently, considering the versatile nature of the ALD technique, this approach can facilitate the architecturing and design of novel 2D MS and MIS heterojunctions for efficient plasmonic devices.
Collapse
Affiliation(s)
- Mohammad Karbalaei Akbari
- Faculty of Bioscience Engineering , Ghent University Global Campus , 119 Songdomunhwa-ro , Yeonsu-gu, 21985 Incheon , South Korea
| | - Zhenyin Hai
- Faculty of Bioscience Engineering , Ghent University Global Campus , 119 Songdomunhwa-ro , Yeonsu-gu, 21985 Incheon , South Korea
| | - Zihan Wei
- Faculty of Bioscience Engineering , Ghent University Global Campus , 119 Songdomunhwa-ro , Yeonsu-gu, 21985 Incheon , South Korea
| | - Christophe Detavernier
- Department of Solid State Sciences , Ghent University , Krijgslaan 281/S1 , 9000 Ghent , Belgium
| | - Eduardo Solano
- Department of Solid State Sciences , Ghent University , Krijgslaan 281/S1 , 9000 Ghent , Belgium
- NCD Beamline , ALBA Synchrotron Light Source , Carrer de la Llum, 2-26 , 08290 Cerdanyola del Vallès , Spain
| | - Francis Verpoort
- Faculty of Bioscience Engineering , Ghent University Global Campus , 119 Songdomunhwa-ro , Yeonsu-gu, 21985 Incheon , South Korea
- National Research Tomsk Polytechnic University , Lenin Avenue 30 , 634050 Tomsk , Russian Federation
- Laboratory of Organometallics, Catalysis and Ordered Materials, State Key Laboratory of Advanced Technology for Materials Synthesis and Processing, Center for Chemical and Material Engineering , Wuhan University of Technology , 430070 Wuhan , P. R. China
| | - Serge Zhuiykov
- Faculty of Bioscience Engineering , Ghent University Global Campus , 119 Songdomunhwa-ro , Yeonsu-gu, 21985 Incheon , South Korea
| |
Collapse
|
22
|
Wei Z, Hai Z, Akbari MK, Hu J, Hyde L, Depuydt S, Verpoort F, Zhuiykov S. Ultrasensitive, Sustainable, and Selective Electrochemical Hydrazine Detection by ALD-Developed Two-Dimensional WO3. ChemElectroChem 2017. [DOI: 10.1002/celc.201700968] [Citation(s) in RCA: 14] [Impact Index Per Article: 1.8] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/11/2022]
Affiliation(s)
- Zihan Wei
- Ghent University Global Campus; Department of Applied Analytical & Physical Chemistry; 119 Songdomunhwa-ro Yeonsu-gu, Incheon South Korea
| | - Zhenyin Hai
- Ghent University Global Campus; Department of Applied Analytical & Physical Chemistry; 119 Songdomunhwa-ro Yeonsu-gu, Incheon South Korea
| | - Mohammad Karbalaei Akbari
- Ghent University Global Campus; Department of Applied Analytical & Physical Chemistry; 119 Songdomunhwa-ro Yeonsu-gu, Incheon South Korea
| | - Jie Hu
- Micro and Nano System Research Center; Key Lab of Advanced Transducers and Intelligent Control System; (Ministry of Education) & College of Information Engineering; Taiyuan University of Technology; Taiyuan 030024, Shanxi PR China
| | - Lachlan Hyde
- Factory of the Future, Swinburne University of Technology; Hawthorn Australia
| | - Stephen Depuydt
- Ghent University Global Campus; Department of Applied Analytical & Physical Chemistry; 119 Songdomunhwa-ro Yeonsu-gu, Incheon South Korea
| | - Francis Verpoort
- Ghent University Global Campus; Department of Applied Analytical & Physical Chemistry; 119 Songdomunhwa-ro Yeonsu-gu, Incheon South Korea
- National Research Tomsk Polytechnic University; Lenin Avenue 30 634050 Tomsk Russian Federation
- Laboratory of Organometallics, Catalysis and Ordered Materials; State Key Laboratory of Advanced Technology for Materials Synthesis and; Processing; Center for Chemical and Material Engineering; Wuhan University of Technology; Wuhan P.R. China
| | - Serge Zhuiykov
- Ghent University Global Campus; Department of Applied Analytical & Physical Chemistry; 119 Songdomunhwa-ro Yeonsu-gu, Incheon South Korea
| |
Collapse
|