Adsorptive removal of noxious atrazine using graphene oxide nanosheets: Insights to process optimization, equilibrium, kinetics, and density functional theory calculations

A comparison of freeze- and air-dried chitosan salicylaldehyde/calcium oxide biocomposites for optimized removal of acid red 88 dye

Chitosan salicylaldehyde/calcium oxide nanoparticle (CS-SL/CaO) was synthesized by hydrothermal process and isolated via different drying processes, namely, air-drying (AD) and freeze-drying (FD). The physicochemical properties of freeze-dried CS-SL/CaO nanoparticle (CS-SL/CaO-FD) and air-dried CS-SL/CaO nanoparticle (CS-SL/CaO-AD) were compared. In particular, the adsorption properties reveal that the specific surface area of CS-SL/CaO-FD increased by ca. 6 times (BET SA = 7.28 m2/g) greater than CS-SL/CaO-FD (BET SA = 1.26 m2/g). Also, the adsorptive removal of acid red 88 dye (AR88) from aqueous media was optimized by employing the Box-Behnken design (BBD). The optimal adsorption conditions obtained from desirability functions test for the removal of AR88 dye employed a dosage of 0.09 g/100 mL of adsorbent dosage at a solution pH of 5.6 and 25 °C. The best AR88 dye removal was found for the adsorbents CS-SL/CaO-AD (38.2 %) and CS-SL/CaO-FD (86.1 %), which concur with differences in the adsorbent surface areas. Moreover, the adsorption kinetics and isotherm profiles for CS-SL/CaO-FD were described by the pseudo second order (PSO) and Temkin models, where the maximum adsorption capacity of AR88 by CS-SL/CaO-FD 175.4 was mg/g. These findings reveal the potential application of the CS-SL/CaO-FD towards removal of toxic cationic dye (AR88) from an aqueous environment.

Freeze-drying synthesis of mesoporous magnetic grafted chitosan/calcium oxide nanoparticle for remazol brilliant blue dye removal: A statistical optimization

Herein, a mesoporous magnetic chitosan-salicylaldehyde/calcium oxide nanoparticle (CS-SL/CaO/Fe3O4) biocomposite adsorbent that was prepared via freeze-drying. The CS-SL/CaO/Fe3O4 was utilized for the adsorption of ramazol brilliant blue (RBB) dye from aqueous solution. The physicochemical properties of the CS-SL/CaO/Fe3O4 were evaluated using diverse characterization techniques, including BET, XRD, FTIR, FESEM-EDX, CHNS, and pHpzc. The three main factors for adsorption included the following A: CS-SL/CaO/Fe3O4 dosage (0.02-0.1 g/100 mL), B: pH (4-10), and C: Time (60-540 min). These factors were improved using statistical methods, specifically the Box-Behnken design (BBD). The optimal conditions for achieving maximum RBB removal (62.5 %) are listed: CS-SL/CaO/Fe3O4 dosage of 0.1 g/100 mL, a solution pH of 7, and a contact time of 540 min. The adsorption kinetics and equilibrium isotherms were well described by the pseudo first order (PFO) kinetic and Langmuir isotherm models, respectively. Thus, the CS-SL/CaO/Fe3O4 material has a maximum adsorption capacity (qmax) of 63.3 mg/g for RBB at 25 °C. The adsorption mechanism of RBB onto the CS-SL/CaO/Fe3O4 surface was attributed to electrostatic forces, n-π stacking, H-bonding, and Pi-Pi interactions. Thus, CS-SL/CaO/Fe3O4 represents a recoverable magnetic adsorbent with potential for capture of organic dyes from wastewater.

Complexity of influences on atrazine phytoremediation of coexisting graphene oxide in water: Mitigating its phytotoxicity while decreasing plant removal contribution

Phytoremediation is an efficient technology for the removal of herbicide atrazine (ATZ) contamination in water bodies, but its ability to reduce ATZ under combined pollution remains unclear, especially ATZ co-existing with the emerging pollutant graphene oxide (GO) that may have potential effects on ATZ fate, plants and microbes. Herein, we investigated the phytoremediation potential of an emergent plant (Iris pseudacorus) for ATZ and the response of bacteria in a hydroponic system with and without GO. The results showed that plants enhanced ATZ dissipation in water with the increased removal rate by a factor of 1.7-4.0. GO restricted ATZ uptake by plants, but favored ATZ bioconcentration in cell walls. The plant contributed most to changes in the bacterial communities, decreasing the alpha diversity, while enriching the functional categories involving in amino acid and carbohydrate metabolisms. These findings indicated that I. pseudacorus can be employed as an effective candidate of phytoremediation for ATZ co-existing with GO at environmentally relevant concentrations, tending to recruit bacteria with plant stress tolerance and growth-promotion activities more than with ATZ degradation activities; GO exerted a mitigating effect on ATZ stress improving the barrier function of cell walls, but decreased the contribution of plants to ATZ removal.

Quantification of the Contribution of Heterogeneous Surface Processes to Pollutant Abatement during Heterogeneous Catalytic Ozonation

Heterogeneous surface processes such as adsorption and oxidation with surface-adsorbed reactive oxygen species (ROSad, e.g., adsorbed oxygen atom (*Oad) and hydroxyl radicals (•OHad)) have been suggested to play an important role in pollutant abatement during heterogeneous catalytic ozonation (HCO). However, to date, there is no reliable method to quantitatively evaluate the contribution of heterogeneous surface processes to pollutant abatement (fS) during HCO. In this study, we developed a method by combining probe compound-based experiments with kinetic modeling to distinguish heterogeneous surface processes from homogeneous bulk reactions with aqueous O3 and ROS (•OH and superoxide radicals (O2•-) in the abatement of various pollutants (e.g., atrazine, ibuprofen, tetrachloroethylene, and perfluorooctanoic acid) during HCO with reduced graphene oxide. The results show that the pollutants that have a low affinity for the rGO surface (e.g., ibuprofen and tetrachloroethylene) were essentially abated by homogeneous bulk reactions, while the contribution of heterogeneous surface processes was negligible (fS < 5%). In contrast, heterogeneous surface processes played an important or even dominant role in the abatement of pollutants that have a high surface affinity (e.g., fS = 32-82% for atrazine and perfluorooctanoic acid). This study is a critical first step in quantitatively evaluating the role of heterogeneous surface processes for pollutant abatement during HCO, which is crucial to understanding the mechanism of HCO and designing catalysts for effective pollutant abatement.

Statistical physical modeling insights for urinary analgesic drug adsorption on carbon nanomaterial derivative

The presence of phenazopyridine in water is an environmental problem that can cause damage to human health and the environment. However, few studies have reported the adsorption of this emerging contaminant from aqueous matrices. Furthermore, existing research explored only conventional modeling to describe the adsorption phenomenon without understanding the behavior at the molecular level. Herein, the statistical physical modeling of phenazopyridine adsorption into graphene oxide is reported. Steric, energetic, and thermodynamic interpretations were used to describe the phenomenon that controls drug adsorption. The equilibrium data were fitted by mono, double, and multi-layer models, considering factors such as the numbers of phenazopyridine molecules by adsorption sites, density of receptor sites, and half saturation concentration. Furthermore, the statistical physical approach also calculated the thermodynamic parameters (free enthalpy, internal energy, Gibbs free energy, and entropy). The maximum adsorption capacity at the equilibrium was reached at 298 K (510.94 mg g-1). The results showed the physical meaning of adsorption, indicating that the adsorption occurs in multiple layers. The temperature affected the density of receptor sites and half saturation concentration. At the same time, the adsorbed species assumes different positions on the adsorbent surface as a function of the increase in the temperature. Meanwhile, the thermodynamic functions revealed increased entropy with the temperature and the equilibrium concentration.

Changes of atrazine dissipation and microbial community under coexistence of graphene oxide in river water

The coexistence of herbicide atrazine (ATZ) and the nanomaterial graphene oxide (GO) in natural water bodies will be an inevitable scenario due to their widespread application and consequent release into aquatic ecosystems. But the dissipation of ATZ with GO and the response of the microbial community to their combination are still not clear. Here, we investigated the dissipation dynamics and transformation of ATZ with and without GO in river water after 21-d incubation. In the presence of GO, ATZ residue significantly decreased by 11%-43%; the transformation of ATZ markedly increased by 11%-17% when ATZ concentrations were not above 1.0 mg∙L-1. The direct adsorption of ATZ on GO, mainly via π-π interactions, proton transfer and hydrogen bonding, contributed 54%-68% of the total increased ATZ dissipation by GO. ATZ and ATZ+GO exerted effects of similar magnitude on microbial OTU numbers with an increase of bacterial diversity. The coexisting GO increased the relative abundance of ATZ-degradation bacteria and Chitinophagales, thus improving ATZ transformation. This work indicated that the coexistence of GO at environmentally relevant concentrations can effectively reduce ATZ residues and promote the transformation of ATZ to degradation products in river water; nevertheless, the potential risk of GO acting as an ATZ carrier should be given more prominence.

Preparation and characterization of EI-Co/Zr@AC and the mechanisms underlying its removal for atrazine in aqueous solution

Atrazine, a widely used herbicide in agriculture, is detrimental to both the ecological environment and human health owing to its extensive use, poor degradability, and biotoxicity. The technology commonly used to remove atrazine from water is activated carbon adsorption, but it has the problems of difficult recovery, secondary contamination, and a low removal rate. To efficiently remove atrazine from agricultural wastewater, in this study, a new environmental material, embedding immobilization (EI)-Co- and Zr-modified activated carbon powder (Co/Zr@AC), was prepared by immobilizing the bimetallic Co/Zr@AC via EI technique and employed to remove atrazine. When preparing EI-Co/Zr@AC, the single-factor experiment was conducted and determined the optimal preparation conditions: sodium alginate 2.5% (wt), calcium chloride 4.0% (wt), Co/Zr@AC 1.0% (wt), and bentonite 2.0% (wt). The prepared EI-Co/Zr@AC has a three-dimensional mesh structure and many pores and also possesses good mass transfer performance and mechanical properties. The removal efficiency by EI-Co/Zr@AC for the removal of 5.0 mg/L atrazine from 50 mL was 94.1% at pH 7.0 and 25°C, with an EI-Co/Zr@AC dosage of 0.8 g. The mechanistic study showed that the pseudo-second-order kinetic model could describe the removal process better than the pseudo-first-order kinetic model, and the Freundlich isotherm model fit better than other isotherm models. Additionally, the synthesized EI-Co/Zr@AC spheres demonstrated good reusability, with the atrazine removal rate remaining 70.4% after five cycles, and the mechanical properties of the spheres were stable.

Simultaneous adsorption of methylene blue and amoxicillin by starch-impregnated MgAl layered double hydroxide: Parametric optimization, isothermal studies and thermo-kinetic analysis

Textile and pharmaceutical effluents contain significant amounts of dyes and antibiotics, which pose a serious threat to the ecosystem when discharged directly. Therefore, they should be treated by facile treatment techniques using low-cost materials. Layered double hydroxide (LDH) and its hybrids have emerged as robust and economic adsorbents for water treatment. Herein, magnesium/aluminum LDH and its starch-based composite were synthesized by a co-precipitation technique. The physicochemical features of the developed adsorbents were thoroughly characterized using various analytical tools. The developed materials were tested for the eradication of methylene blue (MB) and amoxicillin (AMX) in batch mode adsorption by varying operating conditions. Adsorption performance depends on the solution's pH. Under optimum adsorption conditions of pH 11, adsorbent dosage of 50 mg/L, and treatment time of 120 min, starch-impregnated MgAl-LDH exhibited maximum MB and AMX adsorption capacities of 114.94 and 48.08 mg/g, respectively. The adsorption mechanism states that hydrogen bonds and weak van der Waals forces are responsible for the removal of pollutants by the developed materials. Moreover, equilibrium and kinetic studies revealed that the removal of dye and antibiotic followed the Freundlich and Langmuir models with the pseudo-second-order reaction kinetics, respectively. The spent adsorbents were regenerated using 0.1 M HCl (for MB) and methanol (for AMX) eluent, and reusability studies ensured that the developed adsorbents retained their performance for up to four consecutive adsorption/desorption cycles. MgAl-LDH and its starch-based hybrid could thus be used to effectively remove organic contaminants from wastewater streams on a commercial scale.

Promoted dissipation and detoxification of atrazine by graphene oxide coexisting in water

The herbicide atrazine (ATZ) has a detrimental effect on the health of aquatic ecosystems and has become a global concern in recent years. But the understanding of its persistence and potential toxicity under combined pollution, especially in the coexistence of other emerging pollutants, remains limited. In this work, the dissipation and transformation of ATZ in combination with graphene oxide (GO) in water were investigated. Results showed that dissipation rates of ATZ dramatically increased by 15-95% with half-lives shortened by 15-40% depending on initial concentrations of ATZ, and the products were mainly toxic chloro-dealkylated intermediates (deethylatrazine (DEA) and deisopropylatrazine (DIA)), but their contents were significantly lower under the coexistence of GO compared to ATZ alone. In the presence of GO, the nontoxic dechlorinated metabolite hydroxyatrazine (HYA) was detected earlier than 2-9 days, and ATZ transformation into HYA was increased by 6-18% during 21-day incubation periods. This study indicated that the coexistence of GO enhanced the dissipation and detoxification of ATZ. From a remediation standpoint, GO-induced hydrolytic dechlorination of ATZ can reduce its ecological toxicity. But the environmental risks of ATZ for aquatic ecosystem under the coexistence of GO should still be given the necessary prominence due to the potential hazard of ATZ adsorbed on GO and the predominant degradation products (DEA and DIA).

Bio-sorbent from castor oil polyurethane foam containing cellulose-halloysite nanocomposite for removal of manganese, nickel and cobalt ions from water

In order to mitigate the contamination of water with heavy metals, caused by mining dam failures in Brumadinho and Mariana in Brazil, eco-friendly bio-based castor oil polyurethane foams, containing a cellulose-halloysite green nanocomposite were prepared. Polyurethane foams containing none (PUF-0), 5%wt (PUF-5), and 10%wt (PUF-10) of the nanocomposite were obtained. The application of the material in aqueous media was verified through an investigation of the efficiency of adsorption, the adsorption capacity, and the adsorption kinetics in pH= 2 and pH= 6.5 for manganese, nickel, and cobalt ions. An increase of 5.47 times in manganese adsorption capacity was found after only 30 min in contact with a solution having this ion at pH= 6.5 for PUF-5 and 11.38 times for PUF-10 when both were compared with PUF-0. Adsorption efficiency was respectively 68.17% at pH= 2 for PUF-5% and 100% for PUF-10 after 120 h, while for the control foam, PUF-0, the adsorption efficiency was only 6.90%.

Functional Bimetal/Carbon Composites Co/Zr@AC for Pesticide Atrazine Removal from Water

Atrazine is a toxic and refractory herbicide that poses threats to human health and the ecological environment. In order to efficiently remove atrazine from water, a novel material, Co/Zr@AC, was developed. This novel material is prepared by loading two metal elements, cobalt and zirconium, onto activated carbon (AC) through solution impregnation and high-temperature calcination. The morphology and structure of the modified material were characterized, and its ability to remove atrazine was evaluated. The results showed that Co/Zr@AC had a large specific surface area and formed new adsorption functional groups when the mass fraction ratio of Co²⁺:Zr⁴⁺ in the impregnating solution was 1:2, the immersion time was 5.0 h, the calcination temperature was 500 °C, and the calcination time was 4.0 h. During the adsorption experiment on 10 mg/L atrazine, the maximum adsorption capacity of Co/Zr@AC was shown to be 112.75 mg/g and the maximum removal rate was shown to be 97.5% after 90 min of the reaction at a solution pH of 4.0, temperature of 25 °C, and Co/Zr@AC concentration of 60.0 mg/L. In the kinetic study, the adsorption followed the pseudo-second-order kinetic model (R² = 0.999). The fitting effects of Langmuir and Freundlich isotherms were excellent, indicating that the process of Co/Zr@AC adsorbing atrazine also conformed to two isotherm models, so the adsorption of atrazine by Co/Zr@AC had multiple effects including chemical adsorption, mono-molecular layer adsorption, and multi-molecular layer adsorption. After five experimental cycles, the atrazine removal rate was 93.9%, indicating that Co/Zr@AC is stable in water and is an excellent novel material that can be used repeatedly.

Graphene oxide modified magnetic polyamidoamide dendrimers based magnetic solid phase extraction for sensitive measurement of polycyclic aromatic hydrocarbons

In this study, graphene oxide modified magnetic polyamidoamine dendrimers (MNPs@PAMAM-G2.0@GO) nanoparticles were successfully prepared by amidation method. The obtained MNPs@PAMAM-G2.0@GO nanocomposites were examined by fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), vibrating sample magnetometer (VSM), scanning electron microscope (SEM) and transmission electron microscopy (TEM), etc. MNPs@PAMAM-G2.0@GO exhibited excellent adsorption property and was investigated for magnetic solid phase extraction (MSPE) of polycyclic aromatic hydrocarbons (PAHs) from water. The detection of extracted PAHs was accomplished by high performance liquid chromatography (HPLC) and gas chromatography tandem mass spectrometry (GC-MS/MS). The target PAHs included anthracene (ANT), pyrene (PYR), fluoranthene (FLT), carbazole (CB), 7-methylquinoline (7-MQL), 9-methylcarbazole (9-MCB), dibenzothiophene (DBT) and 4,6-dimethyldibenzothiophene (4,6-DBT). Important operation parameters for MSPE that could affect the extraction efficiencies of PAHs were investigated in detail. Under optimal parameters, the constructed method demonstrated excellent linear range with 0.001-10 μg L^-1 for analytes and low limits of detection within the range of 0.11-0.9 ng L^-1. The spiked average recoveries of PAHs in natural water samples ranged from 92.5% to 105.2%. The promising results indicated that MNPs@PAMAM-G2.0@GO could be employed to efficiently extract PAHs from aqueous samples.