Polyethyleneimine/hydrated titanium oxide-functionalized fibrous adsorbent for removing cobalt: Adsorption performance and irradiation stability

Harnessing the power of polyethyleneimine in modifying chitosan surfaces for efficient anion dyes and hexavalent chromium removal

In this investigation, synthesis of a surface-functionalized chitosan known as amino-rich chitosan (ARCH) was achieved by successful modification of chitosan by polyethyleneimine (PEI). The synthesized ARCH was characterized by a specific surface area of 8.35 m2 g-1 and a microporous structure, with pore sizes predominantly under 25 nm. The Zeta potential of ARCH maintained a strong positive charge across a wide pH range of 3-11. These characteristics contribute to its high adsorption efficiency in aqueous solutions, demonstrated by its application in removing various anionic dyes, including erioglaucine disodium salt (EDS), methyl orange (MO), amaranth (ART), tartrazine (TTZ), and hexavalent chromium ions (Cr(VI)). The adsorption capacities (Qe) for these contaminants were measured at 1301.15 mg g-1 for EDS, 1025.45 mg g-1 for MO, 940.72 mg g-1 for ART, 732.96 mg g-1 for TTZ, and 350.15 mg g-1 for Cr(VI). A significant observation was the rapid attainment of adsorption equilibrium, occurring within 10 min for ARCH. The adsorption behavior was well-described by the Pseudo-second-order and Langmuir models. Thermodynamic studies indicated that the adsorption process is spontaneous and endothermic in nature. Additionally, an increase in temperature was found to enhance the adsorption capacity of ARCH. The material demonstrated robust stability and selective adsorption capabilities in varied conditions, including different organic compounds, pH environments, sodium salt presence, and in the face of interfering ions. After five cycles of adsorption, ARCH maintained about 60% of its initial adsorption capacity. Due to its efficient adsorption performance, simple synthesis process, low biological toxicity, and cost-effectiveness, ARCH is a promising candidate for future water treatment technologies.

Controllably Adjusting the Hydrophobicity of Collagen Fibers for Enhancing the Adsorption Rate, Retention Capacity, and Separation Performance of Flavonoid Aglycones

Collagen fibers (CFs) were previously used as packing materials for the separation of flavonoids based on hydrogen bond and hydrophobic interactions. However, as for flavonoid aglycones, CFs presented unsatisfactory adsorption capacity and separation efficiency due to the fact that they include limited hydroxyls and phenyls. In order to improve the adsorption capacity and separation efficiency, the hydrophobic modification strategy was employed in this research to enhance the hydrophobic interaction of CF with flavonoid aglycones by using silane coupling agents with different alkyl chains (isobutyl, octyl, and dodecyl). FT-IR analysis, DSC, TG, SEM, EDS mapping, water contact angle, and absorption time of solvent proved the successful grafting of alkyl chains on the CF without disturbing its special fiber structure, leading to the significantly enhanced hydrophobicity of the CF. The dynamic adsorption and elution behavior of kaempferol and quercetin (the typical flavonoid aglycones) on the hydrophobic CF showed that the adsorption rate and retention rate were largely increased in comparison with the CF without modification. Molecular dynamic simulations indicated that the CF grafted with isobutyls could interact with flavonoid aglycones through the highest synergetic effect of hydrophobic and hydrogen bond interactions, which exhibited the strongest retention to flavonoid aglycones. On further increasing the alkyl length (octyl and dodecyl), the hydrophobic interaction was further enhanced, but the hydrogen bonds were significantly weakened by steric hindrance, which showed that the retention to flavonoid aglycones was appropriately increased but without causing peak tailing. In the column separation of kaempferol and quercetin, the CF with hydrophobic modification presented a greater separation efficiency, with the purity of kaempferol increased from 71.99 to 86.57-97.50% and the purity of quercetin increased from 82.69 to 88.07-99.37%, which was much better than that of polyamide and close to that of sephadex LH 20. Therefore, the hydrophobicity of the CF could be controllably adjusted to enhance the adsorption rate and retention capacity, specifically improving the separation efficiency of flavonoid aglycones.

Lignin/sodium alginate hydrogel for efficient removal of methylene blue

In this work, a class of bio-based hydrogels (LN-NH-SA hydrogel) were prepared from aminated lignin and sodium alginate. The physical and chemical properties of the LN-NH-SA hydrogel were fully characterized using field emission scanning electron microscopy, thermogravimetric analysis, fourier transform infrared spectroscopy, N₂ adsorption-desorption isotherms, and other techniques. LN-NH-SA hydrogels were tested for the adsorption of dyes (methyl orange and methylene blue). The LN-NH-SA@3 hydrogel showed better adsorption efficiency for MB with a maximum adsorption capacity of 388.81 mg·g^-1, a bio-based adsorbent with a high adsorption capacity. The adsorption process followed the pseudo-second-order model and fitted to the Freundlich isotherm equation. More importantly, LN-NH-SA@3 hydrogel maintained 87.64 % adsorption efficiency after 5 cycles. Overall, the proposed hydrogel with environmentally friendly and low cost is promising for the absorption of dye contamination.

Biosorption kinetics of cerium(III) and cobalt(II) from liquid wastes using individual bacterial species isolated from low-level liquid radioactive wastes

The existence of toxic heavy metals in the aquatic environment has emphasized a considerable exigency to develop several multifunctional biosorbents for their removal. Herein, three individual bacterial species of Cellulosimicrobium cellulans, Bacillus coagulans, and Microbacterium testaceum were successfully isolated from low-level liquid radioactive wastes. Their loading capacities towards cerium and cobalt metal ions were inclusivity inspected under variable operational parameters of pH, primary pollutant concentration, interaction time, temperature, stirring speed, and biosorbent dosage. By analyzing the influence of solution pH, concentration, temperature, biosorbent mass, and agitation speed on the biosorption kinetics, the biosorption process confirms pseudo-second-order kinetic, intraparticle diffusion, and Elovich equation. Remarkably, the isolated Microbacterium testaceum exhibited high loading capacities reaching 68.1 mg g^-1, and 49.6 mg g^-1 towards Ce(III), and Co(II) ions, respectively, at the initial concentration of 2.8 mM, pH 4.5, and 25 °C. Overall, the isolated bacterial species can potentially be offered up as a promising scavenger for Ce(III) and Co(II) from liquid waste effluents.