Structure evolution during film blowing: An experimental study using in-situ small angle X-ray scattering

Blown Composite Films of Low-Density/Linear-Low-Density Polyethylene and Silica Aerogel for Transparent Heat Retention Films and Influence of Silica Aerogel on Biaxial Properties

Blown films based on low-density polyethylene (LDPE)/linear low-density polyethylene (LLDPE) and silica aerogel (SA; 0, 0.5, 1, and 1.5 wt.%) were obtained at the pilot scale. Good particle dispersion and distribution were achieved without thermo oxidative degradation. The effects of different SA contents (0.5–1.5 wt.%) were studied to prepare transparent-heat-retention LDPE/LLDPE films with improved material properties, while maintaining the optical performance. The optical characteristics of the composite films were analyzed using methods such as ultraviolet–visible spectroscopy and electron microscopy. Their mechanical characteristics were examined along the machine and transverse directions (MD and TD, respectively). The MD film performance was better, and the 0.5% composition exhibited the highest stress at break. The crystallization kinetics of the LDPE/LLDPE blends and their composites containing different SA loadings were investigated using differential scanning calorimetry, which revealed that the crystallinity of LDPE/LLDPE was increased by 0.5 wt.% of well-dispersed SA acting as a nucleating agent and decreased by agglomerated SA (1–1.5 wt.%). The LDPE/LLDPE/SA (0.5–1.5 wt.%) films exhibited improved infrared retention without compromising the visible light transmission, proving the potential of this method for producing next-generation heat retention films. Moreover, these films were biaxially drawn at 13.72 MPa, and the introduction of SA resulted in lower draw ratios in both the MD and TD. Most of the results were explained in terms of changes in the biaxial crystallization caused by the process or the influence of particles on the process after a systematic experimental investigation. The issues were strongly related to the development of blown nanocomposites films as materials for the packaging industry.

Effect of the Elongational Flow on the Morphology and Properties of Polymer Systems: A Brief Review

Polymer-processing operations with dominating elongational flow have a great relevance, especially in several relevant industrial applications. Film blowing, fiber spinning and foaming are some examples in which the polymer melt is subjected to elongational flow during processing. To gain a thorough knowledge of the material-processing behavior, the evaluation of the rheological properties of the polymers experiencing this kind of flow is fundamental. This paper reviews the main achievements regarding the processing-structure-properties relationships of polymer-based materials processed through different operations with dominating elongational flow. In particular, after a brief discussion on the theoretical features associated with the elongational flow and the differences with other flow regimes, the attention is focused on the rheological properties in elongation of the most industrially relevant polymers. Finally, the evolution of the morphology of homogeneous polymers, as well as of multiphase polymer-based systems, such as blends and micro- and nano-composites, subjected to the elongational flow is discussed, highlighting the potential and the unique characteristics of the processing operations based on elongation flow, as compared to their shear-dominated counterparts.

Nanosilicates in Compatibilized Mixed Recycled Polyolefins: Rheological Behavior and Film Production in a Circular Approach

Currently, plastic packaging represents a global challenge and has become a key point of attention for governments, media and consumers due to the visibility of the waste it generates. Despite their high resource efficiency, the perceived non-recyclability of polymeric films risks precluding them from being a relevant packaging solution in a circular economy approach. In this regard, the aim of this study was to implement a strategy to try closing the loop, via the mechanical recycling of post-consumer flexible packaging of small size (denoted as Fil-s) to obtain new films. In particular, two lots of Fil-s were used, which are PE/PP blends differing for the PP content and the presence of polar contaminants. The suitability for film blowing extrusion of these recycled materials, as such and after the addition of a compatibilizer and/or a lamellar nanosilicate, was evaluated. It was first evidenced that the difficulty of producing blown films with the pristine recycled materials, due to the frequent bubble breakages, occurring even at low draw ratios. Moreover, the shear and extensional rheological behavior of all Fil-s based systems was usefully correlated with their processability features, evidencing the key roles of the nanofiller to stabilize the bubble and of the compatibilizer to ensure a uniform film deformation, avoiding its premature breakage. Even if the adopted upgrading strategies allowed the production of blown films with both types of Fil-s, the different components of the recycled matrices were proven to significantly affect their processability and final film performances.

A filament stretching rheometer for in situ X-ray experiments: Combining rheology and crystalline morphology characterization

We present a rheometer that combines the possibility to perform in situ X-ray experiments with a precise and locally controlled uniaxial extensional flow. It thus allows us to study the crystallization kinetics and morphology evolution combined with the rheological response to the applied flow field. A constant uniaxial deformation rate is ensured, thanks to a fast control scheme that drives the simultaneous movement of the top and bottom plates during a pulling experiment. A laser micrometer measures the time evolution of the smallest diameter, where the highest stress is concentrated. The rheometer has a copper temperature-controlled oven with the ability to reach 250 °C and a N₂ connection to create an inert atmosphere during the experiments. The innovation of our rheometer is the fixed location of the midfilament position, which is possible because of the simultaneous controlled movement of the two end plates. The copper oven has been constructed with four ad hoc windows: two glass windows for laser access and two Kapton windows for X-ray access. The key feature is the ability to perfectly align the midfilament of the sample to the laser micrometer and to the incoming X-ray beam in a synchrotron radiation facility, making it possible to investigate the structure and morphologies developed during extensional flow. The rheological response measured with our rheometer for low-density polyethylene (LDPE) is in agreement with the linear viscoelastic envelope and with the results obtained from the existing extensional rheometers. To demonstrate the capability of the instrument, we have performed in situ-resolved X-ray experiments on LDPE samples exhibiting extensional flow-induced crystallization.

Manipulation of Chain Entanglement and Crystal Networks of Biodegradable Poly(butylene adipate-co-butylene terephthalate) During Film Blowing through the Addition of a Chain Extender: An In Situ Synchrotron Radiation X-ray Scattering Study

One prerequisite for the large-scale application of biodegradable polymers is the manipulation of macroscopic performances of commercially available biopolymers during processing according to different real service requirements. Herein, the microstructural evolution of poly(butylene adipate-co-butylene terephthalate) (PBAT) modified by chain extender during film blowing was investigated by in situ synchrotron radiation X-ray scattering to unveil the origin of different performances. The chain dynamics difference induced by the chain extender was first characterized by the rheological measurement and ¹H Multiple Quantum (MQ) NMR. It shows that the terminal relaxation is significantly slowed down, while the locally segmental dynamics is not apparently changed. With the assistance of the custom-built film blowing apparatus, the microstructure right above the die exit (D = 13-165 mm) was in situ, simultaneously captured by small- and wide-angle scattering (SAXS/WAXS), where four distinct regimes can be defined. Only the PBAT melt signals are found in regime I, whereas the formation of the mesomorphic domains as shown by the SAXS streaks appearing in regime II. The crystal shows up in regime III, where the WAXS signal appears. A dramatic increment of the crystallinity is found in regime III, which contributes to the continuous increasing bubble modulus with the formation of the crystal-based network. Such a crystal-based network is filled with crystals in regime IV, where the diameter of the PBAT bubble remains constant. The addition of the chain extender is found to significantly influence the structural evolution within different regimes. These dynamics and structure information could supply general guidance for bubble stability improvement and modification of macroscopic performances of biodegradable polymer products.

A novel experimental setup for in situ optical and X-ray imaging of laser sintering of polymer particles

We present a unique laser sintering setup that allows real time studies of the structural evolution during laser sintering of polymer particles. The device incorporates the main features of classical selective laser sintering machines for 3D printing of polymers and at the same time allows in situ visualization of the sintering dynamics with optical microscopy as well as X-ray scattering. A main feature of the setup is the fact that it provides local access to one particle-particle bridge during sintering. In addition, due to the small scale of the device and the specific laser arrangement process, parameters such as the temperature, laser energy, laser pulse duration, and spot size can be precisely controlled. The sample chamber provides heating up to 360 °C, which allows for sintering of commodity as well as high performance polymers. The latter parameters are controlled by the use of a visible light laser combined with an acousto-optic modulator for pulsing, which allows small and precise spot sizes and pulse times and pulse energies as low as 500 μs and 17 μJ. The macrostructural evolution of the particle bridge during sintering is followed via optical imaging at high speed and resolution. Placing the setup in high flux synchrotron radiation with a fast detector simultaneously allows in situ time-resolved X-ray characterizations. To demonstrate the capabilities of the device, we studied the laser sintering of two spherical PA12 particles. The setup provides crucial real-time information concerning the sintering dynamics as well as crystallization kinetics, which was not accessible up to now.