Fabrication of PVA/PAAm IPN hydrogel with high adhesion and enhanced mechanical properties for body sensors and antibacterial activity

Synthesis and thermally-induced gelation of interpenetrating nanogels

Thermally-induced in-situ gelation of polymers and nanogels is of significant importance for injectable non-invasive tissue engineering and delivery systems of drug delivery system. In this study, we for the first time demonstrated that the interpenetrating (IPN) nanogel with two networks of poly (N-isopropylacrylamide) (PNIPAM) and poly (N-Acryloyl-l-phenylalanine) (PAphe) underwent a reversible temperature-triggered sol-gel transition and formed a structural color gel above the phase transition temperature (Tp). Dynamic light scattering (DLS) studies confirmed that the Tp of IPN nanogels are the same as that of PNIPAM, independent of Aphe content of the IPN nanogels at pH of 6.5 ∼ 7.4. The rheological and optical properties of IPN nanogels during sol-gel transition were studied by rheometer and optical fiber spectroscopy. The results showed that the gelation time of the hydrogel photonic crystals assembled by IPN nanogel was affected by temperature, PAphe composition, concentration, and sequence of interpenetration. As the temperature rose above the Tp, the Bragg reflection peak of IPN nanogels exhibited blue shift due to the shrinkage of IPN nanogels. In addition, these colored IPN nanogels demonstrated good injectability and had no obvious cytotoxicity. These IPN nanogels will open an avenue to the preparation and thermally-induced in-situ gelation of novel NIPAM-based nanogel system.

Preparation and characterization of a polyurethane-based sponge wound dressing with a superhydrophobic layer and an antimicrobial adherent hydrogel layer

Bacterial infection poses a significant impediment in wound healing, necessitating the development of dressings with intrinsic antimicrobial properties. In this study, a multilayered wound dressing (STPU@MTAI2/AM1) was reported, comprising a surface-superhydrophobic treated polyurethane (STPU) sponge scaffold coupled with an antimicrobial hydrogel. A superhydrophobic protective outer layer was established on the hydrophilic PU sponge through the application of fluorinated zinc oxide nanoparticles (F-ZnO NPs), thereby resistance to environmental contamination and bacterial invasion. The adhesive and antimicrobial inner layer was an attached hydrogel (MTAI2/AM1) synthesized through the copolymerization of N-[2-(methacryloyloxy)ethyl]-N, N, N-trimethylammonium iodide and acrylamide, exhibits potent adherence to dermal surfaces and broad-spectrum antimicrobial actions against resilient bacterial strains and biofilm formation. STPU@MTAI2/AM1 maintained breathability and flexibility, ensuring comfort and conformity to the wound site. Biocompatibility of the multilayered dressing was demonstrated through hemocompatibility and cytocompatibility studies. The multilayered wound dressing has demonstrated the ability to promote wound healing when addressing MRSA-infected wounds. The hydrogel layer demonstrates no secondary damage when peeled off compared to commercial polyurethane sponge dressing. The STPU@MTAI2/AM1-treated wounds were nearly completely healed by day 14, with an average wound area of 12.2 ± 4.3 %, significantly lower than other groups. Furthermore, the expression of CD31 was significantly higher in the STPU@MTAI2/AM1 group compared to other groups, promoting angiogenesis in the wound and thereby contributing to wound healing. Therefore, the prepared multilayered wound dressing presents a promising therapeutic candidate for the management of infected wounds. STATEMENT OF SIGNIFICANCE: Healing of chronic wounds requires avoidance of biofouling and bacterial infection. However developing a wound dressing which is both anti-biofouling and antimicrobial is a challenge. A multilayered wound dressing with multifunction was developed. Its outer layer was designed to be superhydrophobic and thus anti-biofouling, and its inner layer was broad-spectrum antimicrobial and could inhibit biofilm formation. The multilayered wound dressing with adhesive property could easily be removed from the wound surface preventing the cause of secondary damage. The multilayered wound dressing has demonstrated good abilities to promote MRSA-infected wound healing and presents a viable treatment for MRSA-infected wound.

Sprayable Zwitterionic Antibacterial Hydrogel With High Mechanical Resilience and Robust Adhesion for Joint Wound Treatment

Wound healing in movable parts, including the joints and neck, remains a critical challenge due to frequent motions and poor flexibility of dressings, which may lead to mismatching of mechanical properties and poor fitting between dressings and wounds; thus, increasing the risk of bacterial infection. This study proposes a sprayable zwitterionic antibacterial hydrogel with outstanding flexibility and desirable adhesion. This hydrogel precursor is fabricated by combining zwitterionic sulfobetaine methacrylate (SBMA) with poly(sulfobetaine methacrylate-co-dopamine methacrylamide)-modified silver nanoparticles (PSBDA@AgNPs) through robust electrostatic interactions. About 150 s of exposure to UV light, the SBMA monomer polymerizes to form PSB chains entangled with PSBDA@AgNPs, transformed into a stable and adhesion PSB-PSB@Ag hydrogel at the wound site. The resulting hydrogel has adhesive strength (15-38 kPa), large tensile strain (>400%), suitable shape adaptation, and excellent mechanical resilience. Moreover, the hydrogel displays pH-responsive behavior; the acidic microenvironment at the infected wound sites prompts the hydrogel to rapidly release AgNPs and kill bacteria. Further, the healing effect of the hydrogel is demonstrated on the rat neck skin wound, showing improved wound closing rate due to reduced inflammation and enhanced angiogenesis. Overall, the sprayable zwitterionic antibacterial hydrogel has significant potential to promote joint skin wound healing.

A Comprehensive Review of Hydrogel-Based Drug Delivery Systems: Classification, Properties, Recent Trends, and Applications

As adaptable biomaterials, hydrogels have shown great promise in several industries, which include the delivery of drugs, engineering of tissues, biosensing, and regenerative medicine. These hydrophilic polymer three-dimensional networks have special qualities like increased content of water, soft, flexible nature, as well as biocompatibility, which makes it excellent candidates for simulating the extracellular matrix and promoting cell development and tissue regeneration. With an emphasis on their design concepts, synthesis processes, and characterization procedures, this review paper offers a thorough overview of hydrogels. It covers the various hydrogel material types, such as natural polymers, synthetic polymers, and hybrid hydrogels, as well as their unique characteristics and uses. The improvements in hydrogel-based platforms for controlled drug delivery are examined. It also looks at recent advances in bioprinting methods that use hydrogels to create intricate tissue constructions with exquisite spatial control. The performance of hydrogels is explored through several variables, including mechanical properties, degradation behaviour, and biological interactions, with a focus on the significance of customizing hydrogel qualities for particular applications. This review paper also offers insights into future directions in hydrogel research, including those that promise to advance the discipline, such as stimuli-responsive hydrogels, self-healing hydrogels, and bioactive hydrogels. Generally, the objective of this review paper is to provide readers with a detailed grasp of hydrogels and all of their potential uses, making it an invaluable tool for scientists and researchers studying biomaterials and tissue engineering.

An Electroconductive and Antibacterial Adhesive Nanocomposite Hydrogel for High-Performance Skin Wound Healing

Multifunctional hydrogel adhesives inhibiting infections and enabling the electrical stimulation (ES) of tissue reparation are highly desirable for the healing of surgical wounds and other skin injuries. Herein, a therapeutic nanocomposite hydrogel is designed by integrating β-cyclodextrin-embedded Ag nanoparticles (CDAgNPs) in a polyvinyl alcohol (PVA) matrix enhanced with free β-cyclodextrin (CD) and an atypical macromolecule made of β-glucan grafted with hyaluronic acid (HAG). The main objective is to develop a biocompatible dressing combining the electroconductivity and antibacterial activity of CDAgNPs with the cohesiveness and porosity of PVA and the anti-inflammatory, moisturizing, and cell proliferation-promoting properties of HAG. The last component, CD, is added to strengthen the network structure of the hydrogel. PVA/CD/HAG/CDAgNP exhibited excellent adhesion strength, biocompatibility, electroconductivity, and antimicrobial activity against a wide range of bacteria. In addition, the nanocomposite hydrogel has a swelling ratio and water retention capacity suitable to serve as a wound dressing. PVA/CD/HAG/CDAgNP promoted the proliferation of fibroblast in vitro, accelerated the healing of skin wounds in an animal model, and is hemostatic. Upon ES, the PVA/CD/HAG/CDAgNP nanocomposite hydrogel became more efficient both in vitro and in vivo further speeding up the skin healing process thus demonstrating its potential as a next-generation electroconductive wound dressing.

Nanocellulose-Based Ecofriendly Nanocomposite for Effective Wastewater Remediation: A Study on Its Process Optimization, Improved Swelling, Adsorption, and Thermal and Mechanical Behavior

A nanocellulose (NC)-based cross-linked adsorbent has been employed herein for the removal of dye pollutants (e.g., methylene blue) from the textile industry. The synthesized hydrogel was optimized to achieve the best concentrations of the adsorbent constituents, i.e., 1.55% guar gum, 1.46% NC, and 0.84% borax for achieving the maximum swelling index (SI, 3741.42%) and higher adsorption capacity (qe, 24.05 mg g-1). 98.8% of dye qe was achieved at optimal conditions of pH 8 within 30 min at 30 °C. Adsorption isotherms and kinetics investigations showed good correlation with the Freundlich adsorption isotherm model (R2 > 0.9889; ΔG° = -4.71; ΔH° = -12.30; ΔS° = -0.025) as well as the pseudo-second-order kinetics model, indicating multilayered and intricate adsorption mechanisms for dye removal. The study of thermodynamic parameters confirmed the exothermic nature of the adsorption process. The adsorption-desorption study of the resulting hydrogel exhibited 64.58% dye removal efficiency even after 4 consecutive cycles of reuse. Further, scanning electron microscopy, Fourier transform infrared spectroscopy, thermogravimetric analysis, and X-ray diffraction analysis revealed the surface morphology, functional moieties, thermal behavior, and crystallinity pattern of the hydrogel. Rheological analysis demonstrated pseudoplastic flow and improved mechanical behavior for the hydrogel. The current study found that the synthesized adsorbent with a higher SI and qe has a noticeable potential for the removal of dye pollutants from wastewater.

Bionic ordered structured hydrogels: structure types, design strategies, optimization mechanism of mechanical properties and applications

Natural organisms, such as lobsters, lotus, and humans, exhibit exceptional mechanical properties due to their ordered structures. However, traditional hydrogels have limitations in their mechanical and physical properties due to their disordered molecular structures when compared with natural organisms. Therefore, inspired by nature and the properties of hydrogels similar to those of biological soft tissues, researchers are increasingly focusing on how to investigate bionic ordered structured hydrogels and render them as bioengineering soft materials with unique mechanical properties. In this paper, we systematically introduce the various structure types, design strategies, and optimization mechanisms used to enhance the strength, toughness, and anti-fatigue properties of bionic ordered structured hydrogels in recent years. We further review the potential applications of bionic ordered structured hydrogels in various fields, including sensors, bioremediation materials, actuators, and impact-resistant materials. Finally, we summarize the challenges and future development prospects of bionic ordered structured hydrogels in preparation and applications.

Characterization of structural and functional properties of soy protein isolate and sodium alginate interpenetrating polymer network hydrogels

BACKGROUND

This study used enzymatic and Ca2+ cross-linking methods to prepare edible soy protein isolate (SPI) and sodium alginate (SA) interpenetrating polymer network hydrogels to overcome the disadvantages of traditional interpenetrating polymer network (IPN) hydrogels, such as poor performance, high toxicity, and inedibility. The influence of changes in SPI and SA mass ratio on the performance of SPI-SA IPN hydrogels was investigated.

RESULTS

Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM) were used to characterize the structure of the hydrogels. Texture profile analysis (TPA), rheological properties, swelling rate, and Cell Counting Kit-8 (CCK-8) were used to evaluate physical and chemical properties and safety. The results showed that, compared with SPI hydrogel, IPN hydrogels had better gel properties and structural stability. As the mass ratio of SPI-SA IPN changed from 1:0.2 to 1:1, the gel network structure of hydrogels also tended to be dense and uniform. The water retention and mechanical properties of these hydrogels, such as storage modulus (G'), loss modulus (G"), and gel hardness increased significantly and were greater than those of the SPI hydrogel. Cytotoxicity tests were also performed. The biocompatibility of these hydrogels was good.

CONCLUSIONS

This study proposes a new method to prepare food-grade IPN hydrogels with mechanical properties of SPI and SA, which may have strong potential for the development of new foods. © 2023 Society of Chemical Industry.

Recent Advances of Natural-Polymer-Based Hydrogels for Wound Antibacterial Therapeutics

Hydrogels have a three-dimensional network structure and high-water content, are similar in structure to the extracellular matrix, and are often used as wound dressings. Natural polymers have excellent biocompatibility and biodegradability and are commonly utilized to prepare hydrogels. Natural-polymer-based hydrogels can have excellent antibacterial and bioactive properties by loading antibacterial agents or being combined with therapeutics such as phototherapy, which has great advantages in the field of treatment of microbial infections. In the published reviews of hydrogels used in the treatment of infectious wounds, the common classification criteria of hydrogels include function, source of antibacterial properties, type of antibacterial agent, etc. However, there are few reviews on the classification of hydrogels based on raw materials, and the description of natural-polymer-based hydrogels is not comprehensive and detailed. In this paper, based on the principle of material classification, the characteristics of seven types of natural polymers that can be used to prepare hydrogels are discussed, respectively, and the application of natural-polymer-based hydrogels in the treatment of infectious wounds is described in detail. Finally, the research status, limitations, and prospects of natural-polymer-based hydrogels are briefly discussed.

Self-healing liquid metal hydrogel for human-computer interaction and infrared camouflage

Due to their mechanical flexibility, conductive hydrogels have been widely investigated in the fields of flexible electronics and soft robots, but their non-negligible disadvantages, such as poor toughness and limited self-healing, severally restrict their practical application. Herein, gallium indium alloy (EGaIn) is utilized to initiate the polymerization and simultaneously serve as flexible fillers to construct a super-stretchable and self-healing liquid metal/polyvinyl alcohol/p(acrylamide-co-octadecyl methacrylate) (liquid metal/PVA/P(AAm-co-SMA)) double network hydrogel (LM hydrogel). The synergistic effect of the rigid PVA microcrystal network and the ductile P(AAm-co-SMA) hydrophobic network, together with the ionic coordination and hydrogen bonds between polymer networks (multiple physical cross-links), endow the LM hydrogel with excellent super-stretchability (2000%), toughness (3.00 MJ m-3), notch resistance, and self-healing property (healing efficiency > 99% at 25 °C after 24 h). The LM hydrogel exhibits sensitive strain sensing behavior, allowing human-computer interaction to achieve motion recognition and health monitoring. Significantly, owing to the excellent photothermal effect and low infrared emissivity of EGaIn, the LM hydrogel reveals great potential in infrared camouflage. The work of self-healing conductive liquid metal hydrogels will promote the research and practical application of hydrogels and liquid metal in intelligent devices and military fields.

Facile fabrication of a broad-spectrum starch/poly(α-l-lysine) hydrogel adsorbent with thermal/pH-sensitive IPN structure through simultaneous dual-click strategy

A thermal/pH-sensitive interpenetrating network (IPN) hydrogel was prepared facilely from starch and poly(α-l-lysine) through amino-anhydride and azide-alkyne double-click reactions in one pot. The synthesized polymers and hydrogels were systematically characterized using different analytical techniques such as Fourier transform infrared spectroscopy (FTIR), nuclear magnetic resonance (NMR), scanning electron microscope (SEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and rheometer. The preparation conditions of the IPN hydrogel were optimized via one-factor experiments. Experimental results indicated the IPN hydrogel possessed pH and temperature sensitivity. Effect of different parameters (pH, contact time, adsorbent dosage, initial concentration, ionic strength, and temperature) on adsorption behavior were investigated in monocomponent system with cationic methylene blue (MB) and anionic Eosin Y (EY) as model pollutants. The results indicated that the adsorption process of the IPN hydrogel for MB and EY followed pseudo-second-order kinetics. The adsorption data for MB and EY fitted well with the Langmuir isotherm model, indicating monolayer chemisorption. The good adsorption performance was due to various active functional groups (-COOH, -OH, -NH₂, etc.) in the IPN hydrogel. The strategy described here opens up a new way for preparing IPN hydrogel. The as-prepared hydrogel exhibits potential application and bright prospects as an adsorbent in wastewater treatment.

Bio-Inspired Low-Cost Fabrication of Stretchable, Adhesive, Transparent, and Multi-Functionalized Joint Wound Dressings

Ideal joint wound dressings should not only promote wound healing and have good mechanical properties including stretchability and adhesion but also possess functions such as sterilization or motion monitoring. The multiple characteristic requirements have greatly limited the material's alternative, resulting in research on functional joint wound dressings falling far short of market demand. Therefore, low-cost, comprehensive designs need to be developed. Herein, inspired by the spiral arteries in the endometrium, alginate-based helical fibers were introduced into polyacrylamide/gelatin (PAM-Gel) to obtain composite polymer membranes, realizing a combination of both mechanical and functional properties. Large scale (100 m) and high-throughput (10 times higher than literature) fabrication of helical microfibers were first achieved, ensuring the low cost of fiber preparation. The composite film had adequate stretchability (>300% strain), adhesion strength (14 kPa), high transparency, and good biocompatibility. The helical fibers could be easily functionalized without affecting the mechanical properties of the dressings, thus broadening the range of materials available for joint dressings. After different treatments of the helical fibers, controlled drug release and joint motion monitoring were realized. Therefore, this helical microfiber composite membrane design achieved low-cost preparation, good mechanical properties, and functionalities including healing promotion, drug release, and motion monitoring ability, demonstrating application potential.

Visible light laser direct-writing of high-resolution, biocompatible, super-multifunctional and tough hydrogels without photoinitiators in 30 s

Currently, the lack of bioinks and long printing time limits the further development of biofabrication. Here we report a novel biocompatible, multi-functional and tough 3D printable hydrogel via visible light photocrosslinking of polyvinyl alcohol bearing styrylpyridinium group (PVA-SbQ). The high-resolution PVA-SbQ hydrogels with different designed shapes can be generated via laser direct-writing in 30 s without extra toxic crosslinkers or photoinitiators, and demonstrates excellent biocompatibility. The rapid laser direct-writing technology also results in a super-strong, tough hydrogel with excellent adhesive, swelling, self-healing, and photo-tunable properties due to the photodimerization of styrylpyridinium (SbQ) groups and the left-over massive amount of free hydroxyl groups in the hydrogel. For example, the maximum tensile strength, elongation, compressive strength adhesive strength of printed PVA-SbQ hydrogels can reach 1.0 MPa, 810 %, 33 MPa, 31 kPa, and 25,000 % respectively. And these properties can be adjusted by controlling the parameters for laser direct-writing. In addition, the introduced nitrogen cations by SbQ groups further endow hydrogels with the potential to develop novel functionality, which is demonstrated by integrating negatively charged nanocelluloses in the PVA-SbQ system to develop underwater adhesives, anti-freezing (-24.9 °C), and anti-bacterial hydrogels. This discovery opens multiple doors for developing PVA-SbQ based multi-functional hydrogel for various applications including biofabrication and tissue engineering.

Prevention of anastomotic stenosis for decellularized vascular grafts using rapamycin-loaded boronic acid-based hydrogels mimicking the perivascular tissue function

Abnormal proliferation of vascular smooth muscle cells (VSMCs) induces graft anastomotic stenosis, resulting in graft failure. Herein, we developed a drug-loaded tissue-adhesive hydrogel as artificial perivascular tissue to suppress VSMCs proliferation. Rapamycin (RPM), an anti-stenosis drug, is selected as the drug model. The hydrogel was composed of poly (3-acrylamidophenylboronic acid-co-acrylamide) (BAAm) and polyvinyl alcohol. Since phenylboronic acid reportedly binds to sialic acid of glycoproteins which is distributed on the tissues, the hydrogel is expected to be adherent to the vascular adventitia. Two hydrogels containing 25 or 50 mg/mL of BAAm (BAVA25 and BAVA50, respectively) were prepared. A decellularized vascular graft with a diameter of <2.5 mm was selected as a graft model. Lap-shear test indicates that both hydrogels adhered to the graft adventitia. In vitro release test indicated that 83 and 73 % of RPM in BAVA25 and BAVA50 hydrogels was released after 24 h, respectively. When VSMCs were cultured with RPM-loaded BAVA hydrogels, their proliferation was suppressed at an earlier stage in RPM-loaded BAVA25 hydrogels compared to RPM-loaded BAVA50 hydrogels. An in vivo preliminary test reveals that the graft coated with RPM-loaded BAVA25 hydrogel shows better graft patency for at least 180 d than the graft coated with RPM-loaded BAVA50 hydrogel or without hydrogel. Our results suggest that RPM-loaded BAVA25 hydrogel with tissue adhesive characteristics has potential to improve decellularized vascular graft patency.

Novel Strategy for Surface Modification of Titanium Implants towards the Improvement of Osseointegration Property and Antibiotic Local Delivery

The topography and chemical composition modification of titanium (Ti) implants play a decisive role in improving biocompatibility and bioactivity, accelerating osseointegration, and, thus, determining clinical success. In spite of the development of surface modification strategies, bacterial contamination is a common cause of failure. The use of systemic antibiotic therapy does not guarantee action at the contaminated site. In this work, we proposed a surface treatment for Ti implants that aim to improve their osseointegration and reduce bacterial colonization in surgery sites due to the local release of antibiotic. The Ti discs were hydrothermally treated with 3M NaOH solution to form a nanostructured layer of titanate on the Ti surface. Metronidazole was impregnated on these nanostructured surfaces to enable its local release. The samples were coated with poly(vinyl alcohol)-PVA films with different thickness to evaluate a possible control of drug release. Gamma irradiation was used to crosslink the polymer chains to achieve hydrogel layer formation and to sterilize the samples. The samples were characterized by XRD, SEM, FTIR, contact angle measurements, "in vitro" bioactivity, and drug release analysis. The alkaline hydrothermal treatment successfully produced intertwined, web-like nanostructures on the Ti surface, providing wettability and bioactivity to the Ti samples (Ti + TTNT samples). Metronidazole was successfully loaded and released from the Ti + TTNT samples coated or not with PVA. Although the polymeric film acted as a physical barrier to drug delivery, all groups reached the minimum inhibitory concentration for anaerobic bacteria. Thus, the surface modification method presented is a potential approach to improve the osseointegration of Ti implants and to associate local drug delivery with dental implants, preventing early infections and bone failure.

Injectable hydrogels of enzyme-catalyzed cross-linked tyramine-modified gelatin for drug delivery

Enzymatically catalyzed cross-linking is a hydrogel fabrication method that generally is considered to have lower cytotoxicity than traditional chemical cross-linking methods. In order to optimize the properties of injectable hydrogels and expand their applications, an enzyme-catalyzed cross-linked injectable hydrogel was designed. The tyramine-modified gelatin (G-T) was formed into a stable injectable hydrogel by the combination of horseradish peroxidase (HRP) and hydrogen peroxide (H2O2) catalysis. 1H NMR spectroscopy was used to demonstrate the successful modification of gelatin by tyramine. The surface morphology of the prepared hydrogels was characterized jointly by atomic force microscopy (AFM) and scanning electron microscopy (SEM). Rheological tests demonstrated the tunable mechanical strength, formation kinetics, shear thinning and good self-recovery properties of the hydrogels. In addition, the hydrogels can be formed into various shapes by injection. The hydrogel network structure is complex and interlaced, as such it is suitable to encapsulate drugs for controlled release. The drug release from the prepared hydrogels followed the Peppas–Sahlin model and belonged to Fickian diffusion. This study constructed injectable hydrogels through the enzyme-catalyzed cross-linking of modified gelatin and applied the hydrogels for drug release, which is expected to expand the application in biomedical fields.

Herbal molecule-mediated dual network hydrogels with adhesive and antibacterial properties for strain and pressure sensing

Multifunctional integration is the focus of hydrogel-based flexible sensors, and formation of a dual network (DN) could shed light on the fabrication of hydrogels with multifunctionality and enhanced properties. In this study, a DN hydrogel was fabricated by the self-assembly of herbal molecule glycyrrhizic acid (GA) as the first hydrogel network and subsequent photocrosslinking of methacrylated sodium alginate (SA-MA) to form the second network. Profiting from the good compatibility between the two hydrogel networks, the obtained DN hydrogels with a homogeneous porous microstructure were endowed with remarkably enlarged stretching (114.5%) and compression (74.4%) strains. In addition, they were demonstrated to display excellent bacteriostatic activity (>99.9%) against Escherichia coli and Staphylococcus aureus owing to the synergetic antibacterial effect of GA and SA-MA. The DN hydrogels as strain sensors possessed high sensitivity (GF = 1.39), linear sensing (R ² > 0.99), rapid response (180 ms), and good stability (1300 times) for human motion detection. Besides, the DN hydrogels could also be used to conduct pressure sensing such as application of heavy weights and even human pulses. All results suggest that the developed DN hydrogels have great potential in serving as epidermal and implantable flexible sensors for human health monitoring.

Significant Roles of Ions in Enhancing and Functionalizing Anisotropic Hydrogels

Salt ions are multifunctional in living beings, in contrast to their limited efficiency in abiotic materials. Achieving the versatility of salt ions in synthetic materials is promising yet demanding. Here, we report that multivalent metallic ions can act multiple crucial roles in a polyacrylamide/sodium alginate (PAAm/SA) composite hydrogel system, inducing a quadruple effect that toughens and functionalizes the originally weak gel. Fixation of anisotropic structures (effect I), mechanical enhancement (effect II), conductivity improvement (effect III), as well as antifreezing and moisture retention properties (effect IV) simultaneously emerge in the gel, all of which are enabled by the ion effect. The resulting tough hydrogels exhibit excellent comprehensive properties that rival existing state-of-the-art hydrogels, promising a wide range of potential applications. As proof-of-concept demonstrations, extremely durable hydrogel-based soft electronic devices are developed, which operate stably even in harsh environments. We also prove that the ion effect can be induced by other multivalent metallic ions. This work highlights the versatility of salt ions in nonliving materials, providing a simple but enlightening idea for the development of all-around soft materials.

Triblock Superabsorbent Polymer Nanocomposites with Enhanced Water Retention Capacities and Rheological Characteristics

Superabsorbent polymers (SAPs) are useful polymers in a wide range of application fields ranging from the hygiene industry to construction and agriculture. As versatility and high water absorption capacity are their important merits, SAPs usually suffer from low water retention capacity (fast release) and weak mechanical properties. To address these drawbacks, a set of new superabsorbent polymer-Halloysite nanotube (HNT) nanocomposites was synthesized via free radical polymerization of acrylamide, 2-acrylamido-2-methylpropane-1-sulfonic acid, and acrylic acid in the presence of vinyltrimethoxysilane (VTMS) as the crosslinker. FTIR and TGA characterizations confirm the polymerization of SAP and successful incorporation of HNTs into the SAP polymer matrix. The effect of the HNT nanofiller amount in the nanocomposite polymer matrix was investigated with swelling-release performance tests, crosslink density calculations, and rheology measurements. It was found that equilibrium swelling ratios are correlated and therefore can be tuned via the crosslink densities of nanocomposites, while water retention capacities are governed by storage moduli. A maximum swelling of 537 g/g was observed when 5 wt % HNT was incorporated, in which the crosslink density is the lowest. Among the SAP nanocomposites prepared, the highest storage modulus was observed when 1 wt % of nanofiller was incorporated, which coincides with the nanocomposite with the longest water retention. The water release duration of SAPs was prolonged up to 27 days with 1% HNT addition in parallel with the achieved maximum storage modulus. Finally, three different incorporation mechanisms of the HNT nanofiller into the SAP nanocomposite structure were proposed and confirmed with rheology measurements. This study provides a rapid synthesis method for SAP nanocomposites with enhanced water retention capacities and explains the relationship between swelling and crosslink density and water retention and mechanical properties of SAP nanocomposites.

Protein-Based Hydrogels: Promising Materials for Tissue Engineering

The successful design of a hydrogel for tissue engineering requires a profound understanding of its constituents' structural and molecular properties, as well as the proper selection of components. If the engineered processes are in line with the procedures that natural materials undergo to achieve the best network structure necessary for the formation of the hydrogel with desired properties, the failure rate of tissue engineering projects will be significantly reduced. In this review, we examine the behavior of proteins as an essential and effective component of hydrogels, and describe the factors that can enhance the protein-based hydrogels' structure. Furthermore, we outline the fabrication route of protein-based hydrogels from protein microstructure and the selection of appropriate materials according to recent research to growth factors, crucial members of the protein family, and their delivery approaches. Finally, the unmet needs and current challenges in developing the ideal biomaterials for protein-based hydrogels are discussed, and emerging strategies in this area are highlighted.

Oxidized alginate linked tough conjoined-network hydrogel with self-healing and conductive properties for strain sensing

In this article, we prepared a conjoined-network hydrogel with acrylamide-modified chitosan, oxidized alginate and polyacrylamide. The oxidized alginate can not only crosslink with chitosan to form a hydrogel network but...

A review of recent advances in metal ion hydrogels: mechanism, properties and their biological applications

The mechanisms, common properties and biological applications of different types of metal ion hydrogels are summarized.

Conductive Biomaterials as Bioactive Wound Dressing for Wound Healing and Skin Tissue Engineering

Conductive biomaterials based on conductive polymers, carbon nanomaterials, or conductive inorganic nanomaterials demonstrate great potential in wound healing and skin tissue engineering, owing to the similar conductivity to human skin, good antioxidant and antibacterial activities, electrically controlled drug delivery, and photothermal effect. However, a review highlights the design and application of conductive biomaterials for wound healing and skin tissue engineering is lacking. In this review, the design and fabrication methods of conductive biomaterials with various structural forms including film, nanofiber, membrane, hydrogel, sponge, foam, and acellular dermal matrix for applications in wound healing and skin tissue engineering and the corresponding mechanism in promoting the healing process were summarized. The approaches that conductive biomaterials realize their great value in healing wounds via three main strategies (electrotherapy, wound dressing, and wound assessment) were reviewed. The application of conductive biomaterials as wound dressing when facing different wounds including acute wound and chronic wound (infected wound and diabetic wound) and for wound monitoring is discussed in detail. The challenges and perspectives in designing and developing multifunctional conductive biomaterials are proposed as well.

Peptide Hydrogel with Antibacterial Performance Induced by Rare Earth Metal Ions

Metal ion-induced peptide assembly is an interesting field. As compared to traditional antibacterial Ag⁺, rare earth metal ions possess the advantage of antibacterial performance with photostability and low toxicity. Herein, a new peptide Fmoc-FFWDD-OH was designed and synthesized, which could form a stable hydrogel induced by rare earth metal ions, including Tb³⁺, Eu³⁺, and La³⁺. The mechanical properties were characterized by rheological measurements, and they exhibited elasticity-dominating properties. Transmission electron microscopy (TEM) images showed a large number of nanoscale fiber structures formed in the hydrogel. Circular dichroism (CD) spectra, Fourier transform infrared (FT-IR) spectra, ThT assays, and X-ray diffraction (XRD) pattern illustrated the formation mechanism of the fiber structure. The rare earth ion-induced peptide hydrogel was proved to possess good antibacterial performance on Escherichia coli (E. coli) with excellent biocompatibility. The introduction of rare earth metal ions may have some potential applications in the biological antibacterial and medical fields.

Fe3+-citric acid/sodium alginate hydrogel: A photo-responsive platform for rapid water purification

As water pollution in human society becomes more and more serious, the demand for materials that can be used for wastewater treatment is increasing. Here, we reported a sodium alginate-based hydrogel (Fe³⁺-CA/SA hydrogel) that can efficiently photocatalyze the degradation of malachite green. The Fe³⁺-CA/SA hydrogel is composed of sodium alginate, citric acid, and Fe³⁺. The hydrogel has multi-leveled pore structure and photochromic ability. Benefiting from the unique microstructure and positive feedback chemical reaction process, the hydrogel has high photocatalytic efficiency. Under 365 nm UV light irradiation, the hydrogel can degrade around 95% of malachite green (20 mg/L) in about 4 min, and there is no need to add H₂O₂ in the degradation process. The work helps to expand the application of sodium alginate-based hydrogels in the field of water treatment. It also has exploratory significance for the principle of photocatalytic degradation of malachite green.

Drosera-Inspired Dual-Actuating Double-Layer Hydrogel Actuator

Drosera is a small insectivorous plant whose antennae can fold up, encircle, and prey. The rapid movement of the antennae is achieved by the synergistic effect of a double-layer structure with the antennae contracts on the front and expands on the back. In this work, a drosera-inspired dual-actuating double-layer hydrogel actuator is proposed, in which the temperature-responsive poly(N, N-diethyl acrylamide) (PDEAAm) layer acts as the main actuation layer and a moisture-responsive poly(acrylamide) (PAAm) layer acts as the auxiliary actuation layer. In a water environment with low temperature, both the PAAm and PDEAAm layers absorb water and expand with a swelling property. When the temperature exceeds the lower critical solution temperature of PDEAAm, the PDEAAm layer undergoes a hydrophilic-hydrophobic transition and shrinks rapidly. Therefore, the synergistic effect of the double-layer hydrogel enables the double-layer hydrogel to achieve a large bending angle at high temperature. In addition, when designing and fabricating shape-patterned double-layer hydrogels, complex shape changes can be achieved. Due to the physical and chemical properties, the actuator can be used to grab, transport, and release objects. This drosera-inspired double-layer hydrogel actuator has high practical value, which may provide new insights for the design and manufacture of artificial intelligence materials.