Synthesis and characterization Agar/GO/ZnO NPs nanocomposite for removal of methylene blue and methyl orange as azo dyes from food industrial effluents

Development of inorganic and mixed matrix membranes for application in toxic dyes-contaminated industrial effluents with in-situ treatments

Dyes are the most ubiquitous organic pollutants in industrial effluents. They are highly toxic to both plants and animals; thus, their removal is paramount to the sustainability of ecosystem. However, they have shown resistance to photolysis and various biological, physical, and chemical wastewater remediation processes. Membrane removal technology has been vital for the filtration/separation of the dyes. In comparison to polymeric membranes, inorganic and mixed matrix (MM) membranes have shown potentials to the removal of dyes. The inorganic and MM membranes are particularly effective due to their high porosity, enhanced stability, improved permeability, higher enhanced selectivity and good stability and resistance to harsh chemical and thermal conditions. They have shown prospects in filtration/separation, adsorption, and catalytic degradation of the dyes. This review highlighted the advantages of the inorganic and MM membranes for the various removal techniques for the treatments of the dyes. Methods for the membranes production have been reviewed. Their application for the filtration/separation and adsorption have been critically analyzed. Their application as support for advanced oxidation processes such as persulfate, photo-Fenton and photocatalytic degradations have been highlighted. The mechanisms underscoring the efficiency of the processes have been cited. Lastly, comments were given on the prospects and challenges of both inorganic and MM membranes towards removal of the dyes from industrial effluents.

Visible light assisted photooxidative facile degradation of azo dyes in water using a green method

In this study, the methyl orange (MO) dye has been degraded after screening several azo dyes due to its effective results and being toxic and carcinogenic to aquatic life and humans. An environmentally friendly, economical, and green method for water purification was used in this study using the photooxidative method. Several organic acids were screened for oxidative applications against various azo dyes but due to better results, methyl orange was selected for the whole study. Ascorbic acid, also known as vitamin C, was found to be best for photodegradation due to its high oxidative activity among various organic acids utilized. A newly developed photoreactor box has been used to conduct the photooxidation process. To evaluate the degradation efficiency of AsA, photooxidative activity was monitored periodically. When the dose of AsA was used at a contact time of 180 minutes, degradation efficiency was 96%. The analysis of degraded products was performed using HPLC and GC-MS. The nucleophilicity of HOMO-LUMO and MEPs was confirmed using density functional theory. For the optimization of the process, central composite design (CCD) in Response Surface Methodology (RSM) was utilized.

Removal of textile pollutants from aqueous medium using biosynthesized CuO nanoparticles: Theoretical comparative investigation via analytical model

The work deals with the removal of two dyes, namely methylene blue (MB) and methyl orange (MO), from polluted water by adsorption onto CuO nanoparticles synthesized with a green synthesis procedure, starting from plant resources. Adsorption isotherms are determined at different temperatures aiming at investigating the adsorption mechanisms of the two dyes. The experimental results indicate that, for both MB and MO, the adsorption capacity increases with increasing temperature, with slight differences in the case of MO. Comparatively, the CuO nanoparticles show a higher MB adsorption capacity with respect to MO. A modelling analysis is carried out with a multilayer model derived from statistical physics, selected among a group of models, each hypothesizing a different number of adsorbed molecules layers. The analysis of model parameters allows determining that the adsorbate molecules exhibit a non-parallel orientation on the surface of biosynthesized CuO nanoparticles and each functional group of the adsorbent binds multiple molecules, simultaneously.The model also allows determining the number of dye molecule layers formed on adsorbent surface, in all the cases resulting higher than three, also confirming the effect of temperature on the maximum adsorption capacity.Specifically, the total number of dye layers formed on biosynthesized CuO nanoparticles surface exhibited a range of 4.17-4.55 for MB dye and of 3.01-3.51 for MO dye.Finally, the adsorption energies reveal that adsorption likely involves physical forces (all resulting all below 22 kJ/mol), i.e. hydrogen bonding and van der Waals forces. The adsorption energies for the interactions between dye molecules are lower than those calculated for the interactions between the dye molecules and the adsorbent surface.

Surface-modified graphene oxide-based composites for advanced sequestration of basic blue 41 from aqueous solution

Advanced materials for the efficient treatment of textile wastewater need to be developed for the sustainable growth of the textile industry. In this study, graphene oxide (GO) was modified by the incorporation of natural clay (bentonite) and mixed metal oxide (copper-cobalt oxide) to produce GO-based binary and ternary composites. Two binary composites, GO/bentonite and GO/Cu-Co Ox (oxide), and one ternary composite, GO/bentonite/Cu-Co Ox, were characterized by Fourier transform-infrared spectroscopy (FTIR), scanning electron microscope (SEM), energy dispersive spectrometer (EDS) and Brunauer-Emmett-Teller (BET) analysis. The adsorption efficiency of these composites was evaluated against a cationic dye, Basic Blue 41 (BB41). The composites had several surface functional groups, and the ternary composite had tubular porous structures formed by the cross-linking of the bentonite and GO planes. The BET surface area of the ternary composite was 50% higher than that of the GO. The BB41 removals were 92, 89, 80, and 69% for GO/bentonite/Cu-Co oxide, GO/bentonite, GO and GO/Cu-Co oxide, respectively. The pseudo-2nd-order and intraparticle diffusion models best describe the kinetics results, indicating chemisorption and slow pore diffusion-controlled adsorption processes. The Langmuir isotherm-derived adsorption capacity of GO/bentonite/Cu-Co oxide was 351.1 mg/g, which was very close to the measured value. After five consecutive cycles, the ternary composite retained 90% BB41 removal efficiency compared to its 1st cycle. Electrostatic interaction and pore diffusion were predicted to be the controlling mechanisms for the adsorption of the BB41. The GO-based ternary composite can be a feasible and scalable adsorbent for BB41 in wastewater treatment.

Sustainable remediation of dye-contaminated wastewater using novel cross-linked Hex-CCP-co-PPT microspheres

The presence of dyes in contaminated water poses substantial dangers to the health of both humans and aquatic life. A process called precipitation polymerization was used to create unique cross-linked hexa-chlorocyclotriphosphazene-co-phenolphthalein (Hex-CCP-co-PPT) microspheres for the purpose of this research. Advanced methods such as X-ray diffraction (XRD), energy-dispersive X-ray spectroscopy (EDX), scanning electron microscopy (SEM), thermogravimetric analysis (TGA), and differential thermogravimetry (DTG) were used to characterise these microspheres. In a simulated solution, the performance of Hex-CCP-co-PPTs as a sorbent for removing MB dye was investigated, and the results showed an unprecedentedly high removal rate of 88.4% for MB. Temperature of 25 °C, a Hex-CCP-co-PPTs dose of 40 mg, an MB concentration of 20 ppm, an MB solution volume of 20 mL, a contact time of 40 min, and a pH of 9 were found to be the optimal experimental conditions. According to the results of the kinetic and adsorption analyses, the PSO and Langmuir adsorption models are the best ones to use. These models favour the chemi-sorption nature and mono-layered adsorption of MB in comparison to Hex-CCP-co-PPTs. Importantly, the thermodynamic analysis demonstrated that the process of removing MB by utilizing Hex-CCP-co-PPTs was endothermic and occurred spontaneously. These findings highlight the potential application of Hex-CCP-co-PPT microspheres in Algal Membrane Bioreactors (AMBRs) for the efficient and sustainable removal of dye from wastewater. This would contribute to the protection of ecosystems as well as the public's health.

Enzymatic degradation of azo dyes methylene blue and congo red with peroxidase purified from cauliflower using affinity chromatography technique: Kinetic study, optimization and metal binding activity

The effective results of the enzymatic decolorization of industrial azo dyes found in wastewater, which cause serious health and environmental problems, with peroxidases have recently increased the interest in these enzyme sources. Redox-mediated decolorization of Methylene Blue and Congo Red azo dyes with cauliflower (Brassica oleracea var.botrytis L.) peroxidase (CPOD) purified in one step using 4-amino 3-bromo 2-methyl benzohydrazide molecule was investigated for the first time. The inhibition effect of this molecule, which is used as a ligand in affinity chromatography, on the CPOD enzyme was investigated. The K_i and IC₅₀ values for this enzyme were calculated as 0.113 ± 0.012 mM and 0.196 ± 0.011 mM, respectively. With the affinity gel obtained by binding to the Sepharose-4B-l-tyrosine matrix of this molecule, which shows a reversible inhibition effect, the purification values of CPOD enzyme were determined as 562-fold with a specific activity of 50,250 U mg^-1. The purity of the enzyme was checked by the SDS-PAGE technique and its molecular weight was determined. A single band at 44 kDa was observed for the CPOD enzyme. In dye decolorization studies, the effects of dye, enzyme, and hydrogen peroxide concentrations as well as time, pH, and temperature were investigated. The profiles of the optimum conditions for both dyes were similar, and the percentages of decolorization of Methylene Blue and Congo Red under these conditions were 89% and 83%, respectively, at the end of the 40 min reaction time. Again, when examining the effect of metal ions on enzyme activity, it was found that there was no significant negative change in CPOD.

Adsorbent biochar derived from corn stalk core for highly efficient removal of bisphenol A

Environmental-friendly biochar (BC) with low cost was obtained by simple pyrolysis of corn stalk core, which was employed as an adsorbent for efficiently removing organic pollutants in water. The physicochemical properties of BCs were characterized by various techniques, including X-ray diffractometer (XRD), Fourier transforms infrared (FT-IR), scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectrometer (XPS), Raman, Thermogravimetric (TGA), N₂ adsorption-desorption and zeta potential tests. The influence of pyrolysis temperature on the structure and adsorption efficiency of the adsorbent was emphasized. The graphitization degree and sp² carbon content of BCs were enhanced by increasing the pyrolysis temperature, which was favorable for the enhancement of the adsorption efficiency. The adsorption results showed that corn stalk core calcined at 900 °C (BC-900) displayed exceptional adsorption efficiency toward bisphenol A (BPA) in wide pH (1-13) and temperature (0-90 °C) ranges. Moreover, adsorbent BC-900 could adsorb various pollutants from water, including antibiotics, organic dyes, and phenol (50 mg·L^-1). The adsorption process of BPA over BC-900 matched well with the Langmuir isotherm and pseudo-second-order kinetic model. Mechanism investigation suggested that large specific surface area and pore filling acted the foremost role in the adsorption process. Adsorbent BC-900 has the potential application in wastewater treatment due to its simple preparation, low cost, and excellent adsorption efficiency.

Synthesis of Ruthenium-Promoted ZnO/SBA-15 Composites for Enhanced Photocatalytic Degradation of Methylene Blue Dye

Synthetic organic pigments like xanthene and azo dyes from the direct discharge of textile effluents are considered colossal global issues and attract the concern of scholars. Photocatalysis continues to be a very valuable pollution control method for industrial wastewater. Incorporations of metal oxide catalysts such as zinc oxide (ZnO) on mesoporous Santa Barbara Armophous-15 (SBA-15) support to improve catalyst thermo-mechanical stability have been comprehensively reported. However, charge separation efficiency and light absorption of ZnO/SBA-15 continue to be limiting its photocatalytic activity. Herein, we report a successful preparation of Ruthenium-induced ZnO/SBA-15 composite via conventional incipient wetness impregnation technique with the aim of boosting the photocatalytic activity of the incorporated ZnO. Physicochemical properties of the SBA-15 support, ZnO/SBA-15, and Ru-ZnO/SBA-15 composites were characterized by X-ray diffraction (XRD), N₂ physisorption isotherms at 77 K, Fourier-transform infrared (FTIR), scanning electron microscopy (SEM), energy dispersive X-ray (EDS), and transmission electron microscopy (TEM). The characterization outcomes exhibited that ZnO and ruthenium species have been successfully embedded into SBA-15 support, andtheSBA-15 support maintains its structured hexagonal mesoscopic ordering in both ZnO/SBA-15 and Ru-ZnO/SBA-15 composites. The photocatalytic activity of the composite was assessed through photo-assisted mineralization of aqueous MB solution, and the process was optimized for initial dye concentration and catalyst dosage. 50 mg catalyst exhibited significant degradation efficiency of 97.96% after 120 min, surpassing the efficiencies of 77% and 81% displayed by 10 and 30 mg of the as-synthesized catalyst. The photodegradation rate was found to decrease with an increase in the initial dye concentration. The superior photocatalytic activity of Ru-ZnO/SBA-15 over the binary ZnO/SBA-15 may be attributed to the slower recombination rate of photogenerated charges on the ZnO surface with the addition of ruthenium.

Facile synthesis and characterization of magnesium and manganese mixed oxides for the efficient removal of tartrazine dye from aqueous media

Nanomaterials are the most effective class of substances for use as adsorbents in wastewater treatment. Hence, the current study involves the facile and low-cost synthesis of MgMn₂O₄/Mn₂O₃ and MgMn₂O₄/Mn₂O₃/Mg₆MnO₈ as novel nanostructures from mixed solutions of Mg(ii) and Mn(ii) ions using the Pechini sol-gel method. After that, the remaining powder was calcined at 500, 700, and 900 °C for 3 h; the products were designated as G500, G700, and G900, respectively. The G500 sample consists of MgMn₂O₄ and Mn₂O₃, while the G700 and G900 samples consist of MgMn₂O₄, Mg₆MnO₈, and Mn₂O₃. The synthesized nanostructures were characterized using several tools, such as X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), and N₂ adsorption/desorption analysis. The average crystallite size of the G500, G700, and G900 samples is 210.53, 95.27, and 83.43 nm, respectively. The SEM images showed that the G500 sample consists of square and rectangular bars with an average diameter of 3.18 μm. Also, the G700 and G900 samples consist of hexagonal, polyhedral, and irregular shapes with an average diameter of 1.12 and 0.54 μm, respectively. The synthesized nanostructures were further utilized as adsorbents for the efficient removal of tartrazine dye from aqueous media. The experimental data showed a good fit with the Langmuir isotherm and pseudo-first-order model. The maximum adsorption capacities of the G500, G700, and G900 adsorbents toward tartrazine dye are 328.95, 359.71, and 395.26 mg g^-1, respectively.

Removing methylene blue from water: A study of sorption effectiveness onto nanoparticles-doped activated carbon

In this present study, silver (Ag) and titanium dioxide (TiO₂) nanoparticles were successfully deposited on coconut shell-derived activated carbon (CSAC), to synthesize a novel nanocomposite (CSAC@AgNPs@TiO₂NPs) for the adsorption of Methylene Blue (MB) dye from aqueous solution. The fabricated CSAC@AgNPs@TiO₂NPs nanocomposite was analyzed by Scanning Electron Microscope (SEM), X-ray Diffraction (XRD), Fourier-Transform Infrared Spectroscopy (FTIR), Transmission Electron Microscope (TEM) equipped with Energy Dispersive X-ray spectroscopy (EDS) detector, X-ray Photoelectron Spectroscope (XPS), and Brunauer-Emmett-Teller (BET). The successful deposition of AgNPs and TiO₂NPs on CSAC surface was revealed by the TEM/EDX, SEM, and XPS analysis. The mesopore structure of CSAC@AgNPs@TiO₂NPs has a BET surface area of 301 m²/g. The batch adsorption studies were conducted and the influence of different parameters, i.e., adsorbent dose, adsorption time, initial dye concentration, pH and temperature were investigated. The nonlinear isotherm and kinetic modelling demonstrated that adsorption data were best fitted by Sips isotherm and pseudo-second-order models, respectively. The maximum adsorption capacity of MB onto CSAC@AgNPs@TiO₂NPs by the Sips model was 184 mg/g. Thermodynamic results revealed that the adsorption was endothermic, spontaneous and physical in nature. CSAC@AgNPs@TiO₂NPs revealed that MB absorption by CSAC@AgNPs@TiO₂NPs was spontaneous and endothermic. The uptake capacity of MB was influenced significantly by the presence of competing ions including, NO₃^-, HCO_3, Ca²⁺, and Na⁺. Repeated tests indicated that the CSAC@AgNPs@TiO₂NPs can be regenerated and reused six times before being discarded. The primary separation mechanism between MB dye and CSAC@AgNPs@TiO₂NPs was the electrostatic interaction. Thus, CSAC@AgNPs@TiO₂NPs was an outstanding material, which displayed good applicability in real water with ≥ 97% removal of MB dye.

Iron-rich coal fly ash-polydopamine-silver nanocomposite (IRCFA-PDA-Ag NPs): tailored material for remediation of methylene blue dye from aqueous solution

Water pollution has become one of the most acute environmental problems. One of the pollutants coming to water bodies from industries are dyes, which are harmful to human health, living organisms, and the esthetic appearance of water. Most dyes are toxic, carcinogenic, rarely biodegradable, and highly soluble in water. Therefore, industrial wastewater treatment has become important. Adsorption technique of removal of dyes from water is simple, efficient, and inexpensive as compared to other techniques. Adsorption efficiency depends on the type and surface area of adsorbents. Iron-rich coal fly ash (IRCFA)-Polydopamine (PDA)@ Silver (Ag) nanocomposite was prepared by separating the iron-rich part (IRCFA) from coal fly ash and coated with polydopamine. IRCFA was mixed with 10 mM tris buffer solution containing 1 g dopamine. The prepared IRCFA-PDA was added to an aqueous solution of silver nitrate, heated at 60 °C, and then 30 mL of flower waste extract was added to this solution. Solid IRCFA-PDA@Ag was obtained, and the prepared nanocomposite was used for the removal of methylene blue (MB) dye from water. The nanocomposite used was prepared by a cost-effective method and has high reusability, separability, and fast regeneration ability. The mechanism of removal of MB dye has been discussed in detail.

Isotherm, Thermodynamics, and Kinetics of Methyl Orange Adsorption onto Magnetic Resin of Chitosan Microspheres

Severe environmental pollution problems arising from toxic dyestuffs (e.g., methyl orange) are receiving increasing attention. Therefore, dyes' safe removal has become a research hotspot. Among the many physical-chemical removal techniques, adsorption using renewable biological resources has proved to be more advantageous over others due to its effectiveness and economy. Chitosan is a natural, renewable biopolymer obtained by deactivated chitin. Thus, the magnetic resin of chitosan microspheres (MRCM), prepared by reversed-phase suspension cross-linking polymerization, was used to remove methyl orange from a solution in a batch adsorption system. The main results are as follows: (1) The results of physical and swelling properties of MRCM indicated that MRCM was a type of black spherical, porous, water-absorbing, and weak alkali exchange resin, and it had the ability to adsorb methyl orange when it was applied in solutions above pH 2.0. (2) In batch adsorption studies, the maximum adsorption capacity was obtained at pH 5; the adsorption equilibrium time was 140 min; and the maximum adsorption was reached at 450 mg/L initial concentration. (3) Among the three isotherm adsorption models, Langmuir achieved the best fit for the adsorption of methyl orange onto MRCM. (4) The adsorption thermodynamics indicated that the adsorption was spontaneous, with increasing enthalpy, and was driven by the entropy. (5) The pseudo-second-order kinetics equation was most suitable to describe the adsorption kinetics, and the adsorption kinetics was also controlled by the liquid-film diffusion dynamics. Consequently, MRCM with relatively higher methyl orange adsorption exhibited the great efficiency for methyl orange removal as an environment-friendly sorbent. Thus, the findings are useful for methyl orange pollution control in real-life wastewater treatment applications.