Phenolic hydroxyl derived copper alginate microspheres as superior adsorbent for effective adsorption of tetracycline

Humidity Induced Proton-Electron Conducting Metal-Organic Frameworks of M3(Hexaiminobenzene)2 (M = Ni, Cu, Fe) for Highly Sensitivity Drug Precursor Chemicals Gases Detection

Exploiting high-performance gas sensors is desirable for the on-site and accurate detection of drug precursor chemical gases. Here, the electron-proton conductivity metal-organic frameworks M3(HIB)2 were designed to discriminate typical drug precursor chemical gases. The strong d-π conjugation and substantial H2O ligands in M3(HIB)2 generate conducting pathways for electrons and protons, which contribute to novel gas-sensing properties. Remarkably, Fe3(HIB)2 demonstrates an ultrahigh response of over 379 toward 60 ppm of toluene at room temperature (RT). Furthermore, the adsorption/desorption behaviors of M3(HIB)2 can be tuned by systematically varying the metal center, causing distinctive gas sensing features for pattern recognition of drug precursor chemical gases. The recognition model was constructed using a convolutional neural networks-gated recurrent unit (CNN-GRU) algorithm, exhibiting a high recognition accuracy. The sensing mechanism is revealed by the Lewis and Brønsted acid site adsorption, due to competitive adsorption between H2O and analyte gases. This work paves the way for the development of proton-electron dual-conducting MOFs for high-performance gas sensors.

Cost-effective synthesis and application of Cu²⁺-doped melamine formaldehyde resin for enhanced tetracycline enrichment in environmental water

Tetracycline antibiotics (TCs) are typically present at low residue levels in environmental water, necessitating enrichment prior to analysis. In this study, a Cu2+-doped melamine formaldehyde resin (Cu-MFR) was synthesized to enhance the adsorption efficiency for TCs, leveraging the formation of stable Cu2+-TC complexes on the sorbent surface. Then it was used as an adsorbent in solid-phase extraction (SPE) for the enrichment of four TCs from water samples. The optimized parameters for Cu-MFR in the analysis of TCs in environmental water enabled linear detection ranges from 0.20 to 50 ng/mL, with relative recoveries ranging from 79.5 % to 97.6 % and relative standard deviations ≤ 10.0 %, using high-performance liquid chromatography-tandem high-resolution mass spectrometry (HPLC-HRMS). The limits of detection for the four TCs were determined to be between 0.11 and 0.16 ng/mL, indicating its potential for practical application in real sample analysis.

Adsorptive removal of oxytetracycline hydrochloride using bagasse-based biochar powder and beads

Oxytetracycline Hydrochloride (OTC), a common antibiotic used to treat specific illnesses in humans and animals, is characterized by poor absorption into cells, low volatility, and high hydrophilicity. It is a potent contaminant that poses a serious threat to the ecosystem, particularly the aquatic sources. Adsorption onto natural adsorbents is one of the most successful, economical, and ecologically friendly ways to remove antibiotics from waste water. The present work focuses on the adsorption of OTC utilizing alginate biochar beads (AlBCB) and biochar powder (BC) derived from bagasse. The influence of several factors were studies and optimized through batch studies employing BC and AlBCB. After 50 min BC displayed a removal of 97%, at an initial concentration of 10 ppm. The experimental data was discovered to follow PFO kinetics and fit with the Freundlich isotherm adsorption model. AlBCB, after a contact time of 40 min, indicated a maximum percentage removal of 86% for initial concentration of 10 ppm OTC. Al-biochar beads showed the maximum percentage removal at pH 10. 0.5 g of adsorbent was used to carry out all batch experiments at room temperature. The adsorption fitted Freundlich adsorption isotherm and intraparticle diffusion kinetics.

Efficient adsorption of chloroquine phosphate by a novel sodium alginate/tannic acid double-network hydrogel in a wide pH range

In this work, a novel double-network composite hydrogel (SA/TA), composed of sodium alginate (SA) and tannic acid (TA), was designed and fabricated by a successive cross-linking method using Ti(IV) and Ca(II) as crosslinkers. SA/TA exhibited reinforced mechanical strength and anti-swelling properties because of the double-network structure. SA/TA was used as an adsorbent for removal of a popular antiviral drug, chloroquine phosphate (CQ), in water. The adsorption performance of SA/TA was systematically investigated, to study various effects including those of TA mass content, solution pH, adsorption time, and initial CQ concentration. Adsorption was also examined in presence of inorganic and organic coexisting substances commonly found in wastewater, and under different actual water samples. Batch experimental results indicated that SA/TA could maintain higher and more stable CQ uptakes within a wide solution pH range from 3.0 to 10.0, compared to its precursor, SA hydrogel, owing to the addition of TA-Ti(IV) coordination network. The maximum experimental CQ uptake exhibited by the 1:1 (by wt) SA/TA (SA/TA2) was as high as 0.699 mmol/g at the initial pH of 9.0. A high concentration of coexisting NaCl evidently reduced the CQ uptakes of SA/TA2 due to the electrostatic shielding effect, moreover, divalent cations including Ca(II) and Mg(II) also inhibited the adsorption of CQ due to competitive adsorption. However, humic acid had little effect on this adsorption. Considering the apparent adsorption performance, the aforementioned effects of various factors and the spectroscopic characterizations, multi-interactions are suggested for adsorption including chelation, electrostatic interactions, π-π electron donor-acceptor interaction and hydrogen bonding. SA/TA showed a slight loss in adsorption capacity toward CQ and sustained physicochemical structural stability, even after six adsorption-desorption cycles. In addition to CQ, SA/TA could be efficiently used for adsorption of two other antivirus drugs, namely, hydroxychloroquine sulfate and oseltamivir phosphate. This work provides an effective strategy for the design and fabrication of novel adsorbents that can effectively adsorb antiviral drugs over a wide pH range.

Tri-modified ferric alginate gel with high regenerative properties catalysts for efficient degradation of rhodamine B

Water pollution caused by dyes has become a focal point of attention. Among them, the heterogeneous Fenton reaction has emerged as an effective solution to this problem. In this study, we designed a ferric alginate gel (PAGM) tri-modified with poly(vinyl alcohol), graphene oxide, and MoS2 as a heterogeneous Fenton catalyst for organic dye degradation. PAGM addresses the drawbacks of alginate gel, such as poor mechanical properties and gel chain dissolution, thereby significantly extending the catalyst's lifespan. The removal rate of rhodamine B by PAGM reached 95.5 % within 15 min, which was 5.9 times higher than that of unmodified ferric alginate gel. Furthermore, due to the π-π interactions, PAGM exhibits unique adsorption properties for pollutants containing benzene rings. Additionally, PAGM can be regenerated multiple times through a simple soaking procedure without any performance degradation. Finally, the reaction column constructed with PAGM maintained an 83.5 % removal rate even after 319 h of continuous wastewater treatment. This work introduces a novel concept for the study of alginate-based gel catalysts in heterogeneous Fenton reactions.

Construction of an allophane-based molecularly imprinted polymer for the efficient removal of antibiotic from aqueous solution

The widespread presence of ciprofloxacin (CIP) antibiotic in the water and soil poses substantial potential risks to the environment, threatening both human and animal health. In this study, we used nanoclay mineral allophane (Allo), β-cyclodextrin (β-CD) as a bifunctional monomer, and sodium alginate as a cross-linking agent, to prepare 3D porous Allo-β-CD molecularly imprinted polymers (MIPs) for the efficient removal of CIP from aqueous solution. The prepared Allo-β-CD MIP was characterized by scanning electron microscopy, transmission electron microscopy, Fourier-transform infrared spectroscopy, X-ray photoelectron spectroscopy, and zeta potential measurements. The effects of initial concentration, time, pH level, and ion concentration on CIP removal dynamics were systematically studied. The adsorption kinetics and equilibrium data of CIP were well-fitted by the pseudo-second-order kinetic model and Langmuir isotherm models, respectively. The Allo-β-CD MIP can efficiently remove CIP from an aqueous solution, with a maximal adsorption capacity of 635 mg/g. It also has impressive recyclability, and enhanced selectivity, and is widely adaptable to various environmental conditions. The adsorption mechanisms of the as-prepared adsorbent include H bonds, hydrophobic interactions, surface complexation, and n-π EDA interactions. Given the experimental evidence, as-prepared adsorbent is therefore a promising candidate for the effective removal of CIP from the aquatic environment.

Batch Experimental Studies and Statistical Modeling for the Effective Removal of Tetracycline from Wastewater Using Bimetallic Zn-Cu-Metal-Organic Framework@Hydrogel Composite Beads

Antimicrobial resistance (AMR) is on an upsurge as more and more broad-spectrum antibiotics are being used haphazardly, resulting in imbalances in the ecosystem and disrupting common/systematic clinical protocols. To combat this issue, metal-organic framework embedded zinc-copper-benzenedicarboxylate@calcium alginate composite beads (Zn-Cu-BDC@CA CBs) were synthesized and utilized for the adsorption of tetracycline (TC) from water. The surface morphology, presence of functional groups, surface area, and thermal stability of Zn-Cu-BDC@CA CBs were evaluated by field emission scanning electron microscopy (FESEM), Fourier transform infrared spectroscopy (FTIR), Brunauer-Emmett-Teller (BET), and thermal gravimetric analysis (TGA), respectively. Batch adsorption experiments were also carried out to optimize the adsorption performance of Zn-Cu-BDC@CA CBs for TC by adjusting the key parameters, including pH of the solution, contact time, adsorbent dosage, temperature, and initial concentration of TC. From the RSM model, 96.8% removal of TC takes place under the optimum conditions (pH = 7.3, mass = 17.2 mg, concentration = 21.3 ppm, time = 3.4 h, and temperature = 31.8 °C), which aligns closely with the experimental batch study, where the addition of 20 mg of adsorbent to a 20 mL TC solution (20 mg/L) at a pH of 7 and a temperature of 27 °C yielded an impressive TC removal efficiency of 96.55% within 180 min. Zn-Cu-BDC@CA CBs possess homogeneous adsorption surfaces, and TC is adsorbed via monolayer chemisorption, according to the results derived from the Langmuir isotherm model and pseudo-second-order kinetic model. The thermodynamic analysis indicated that the adsorption process is both endothermic and spontaneous. In their entirety, the synthesized Zn-Cu-BDC@CA CBs exhibit certain operational advantages, such as simple separation, satisfactory adsorption performance, and decent recyclability, indicating their viability for industrial application of elimination of TC residues from aquatic environments.

Poly(vinyl alcohol)/modified porous starch gel beads for microbial preservation and reactivation: preparation, characterization and its wastewater treatment performance

Poly(vinyl alcohol) (PVA)/modified porous starch (MPS) gel beads were prepared through in situ chemical cross-linking by incorporating with MPS, which was obtained by modifying porous starch (PS) with polyethyleneimine (PEI) and glutaraldehyde (GA). Addition of MPS could improve the storage modulus and the effective crosslinking density (ve) of the gel beads, and the mechanical properties were enhanced. The PVA-MPS gel beads were preserved as immobilized microbial carriers for 40 d and reactivated in wastewater. Scanning electron microscope (SEM) observations showed that the beads were highly porous and conducive for microorganism adhesion. The PVA-MPS gel beads were able to remove 97% of ammonia nitrogen and 80% of chemical oxygen demand (COD) after reactivation under all four preservation conditions. The abundance of Hydrogenophaga as denitrifying bacteria on PVA-MPS gel beads increased, with abundance of 8.44%, 5.55%, 8.90% and 9.48%, respectively. It proved that the carrier provided a partial hypoxic environment for microorganisms.

Adsorption of Copper and Arsenic from Water Using a Semi-Interpenetrating Polymer Network Based on Alginate and Chitosan

New biobased hydrogels were prepared via a semi-interpenetrating polymer network (semi-IPN) using polyacrylamide/chitosan (PAAM/chitosan) hydrogel for the adsorption of As(V) or poly acrylic acid/alginate (PAA/alginate) hydrogel for the adsorption of Cu(II). Both systems were crosslinked using N,N'-methylenebisacrylamide as the crosslinker and ammonium persulfate as the initiating agent. The hydrogels were characterized by SEM, Z-potential, and FTIR. Their performance was studied under different variables, such as the biopolymer effect, adsorbent dose, pH, contact time, and concentration of metal ions. The characterization of hydrogels revealed the morphology of the material, with and without biopolymers. In both cases, the added biopolymer provided porosity and cavities' formation, which improved the removal capacity. The Z-potential informed the surface charge of hydrogels, and the addition of biopolymers modified it, which explains the further metal removal ability. The FTIR spectra showed the functional groups of the hydrogels, confirming its chemical structure. In addition, the adsorption results showed that PAAM/chitosan can efficiently remove arsenic, reaching a capacity of 17.8 mg/g at pH 5.0, and it can also be regenerated by HNO3 for six cycles. On the other hand, copper-ion absorption was studied on PAA/alginate, which can remove with an adsorption capacity of 63.59 mg/g at pH 4.0, and the results indicate that it can also be regenerated by HNO3 for five cycles.

Nonreleasing AgNP Colloids Composite Hydrogel with Potent Hemostatic, Photodynamic Bactericidal and Wound Healing-Promoting Properties

Reactive oxygen species (ROS) produced by noble metallic nanoparticles under visible light is an effective way to combat drug-resistant bacteria colonized on the wound. However, the photocatalytic efficiency of noble metallic nanoparticles is limited by its self-aggregation in water media. Moreover, the fast release of noble metallic ions from nanoparticles might engender cellular toxicity and hazardous environmental issues. Herein, we chose AgNPs, the most common plasmonic noble metallic nanoparticles, as an example, modifying the surface of AgNPs with oleic acid and n-butylamine and imbedded them into calcium alginate (CA) hydrogel that holds tissue adhesion, rapid hemostatic, sunlight-sensitive antibacterial and anti-inflammatory abilities, and thus effectively promotes the healing of wounds. Unlike conventional AgNP-based materials, the constrain of colloids and hydrogel networks hinders the leach of Ag⁺. Nonetheless, the CA/Ag hydrogels exhibit on-demand photodynamic antibacterial efficacy due to the generation of ROS under visible light. In addition, the CA/Ag hydrogel can effectively stop the hemorrhage in a mouse liver bleeding model due to their skin-adaptive flexibility and tissue adhesiveness. The potent sunlight-responsive antibacterial activity of the CA/Ag hydrogel can effectively kill multidrug-resistant bacteria both in vitro (>99.999%) and in vivo (>99.9%), while the diminished Ag⁺ release guarantees its biocompatibility. The CA/Ag hydrogel significantly promotes the wound healing process by the downregulation of proinflammatory cytokines (TNF-α and IL-6) in a rodent full-thickness cutaneous wound model. Overall, the proposed multifunctional CA/Ag nanocomposite hydrogel has excellent prospects as an advanced wound dressing.

Preparation and characterization of chitosan-curdlan composite magnetized by zinc ferrite for efficient adsorption of tetracycline antibiotics in water

Tetracycline (TC) antibiotic-related water pollution directly threatens human health and ecosystems. Here, a zinc ferrite/chitosan-curdlan (ZNF/CHT-CRD) magnetic composite was prepared via a co-precipitation method to be used as a novel, green adsorbent for TC removal from water. Benefiting from a multitude of functional groups, CRD was first crosslinked with CHT and then magnetized with ZNF to provide an easy separation from the solution with an external magnetic force. The successful synthesis and magnetization of the composite were verified with different characterization techniques. The effect of solution pH and composite dosage was carefully evaluated. The optimum solution pH and composite dosage were 6 and 0.65 g/L, respectively, with complete TC removal. The adsorption process by the magnetic composite followed the pseudo-first-order kinetics and Langmuir isotherm models. The maximum adsorption capacity determined from the Langmuir model was 371.42 mg/g at 328 K. Thermodynamic parameters indicated endothermic and spontaneous adsorption. Meanwhile, the composite could be readily separated from the aqueous solution thanks to its magnetic property. Then, it was regenerated with acetone and ethanol to be reused for five more successive cycles. Interestingly, the prepared adsorbent was highly stable and performant in removing TC, maintaining approximately 90 % of its first-cycle adsorption capacity. The adsorption mechanism was primarily attributed to electrostatic and hydrogen bonding attractions. Overall, the currently developed adsorbent could be a more favorable, efficient, and cost-effective candidate than other magnetic chitosan-based composites. These features make it applicable for treating water contaminated with various pharmaceutical pollutants with high separation efficiency and easy recovery under successive adsorption-desorption cycles.

Polyoxometalate supported on a magnetic Fe3O4/MIL-88A rod-like nanocomposite as an adsorbent for the removal of ciprofloxacin, tetracycline and cationic organic dyes from aqueous solutions

In this work, a magnetic H3PW12O40/Fe3O4/MIL-88A (Fe) rod-like nanocomposite as a stable and effective ternary adsorbent was fabricated by the hydrothermal method and utilized for the removal of ciprofloxacin (CIP), tetracycline (TC) and organic dyes from aqueous solution. Characterization of the magnetic nanocomposite was accomplished by FT-IR, XRD, Raman spectroscopy, SEM, EDX, TEM, VSM, BET specific surface area and zeta potential analyses. The influencing factors on the adsorption potency of the H3PW12O40/Fe3O4/MIL-88A (Fe) rod-like nanocomposite including initial dye concentration, temperature and adsorbent dose were studied. The maximum adsorption capacities of H3PW12O40/Fe3O4/MIL-88A (Fe) for TC and CIP were 370.37 mg g-1 and 333.33 mg g-1 at 25 °C, respectively. In addition, the H3PW12O40/Fe3O4/MIL-88A (Fe) adsorbent had high regeneration and reusability capacity after four cycles. In addition, the adsorbent was recovered through magnetic decantation and reused for three consecutive cycles without a considerable reduction in its performance. The adsorption mechanism was mainly ascribed to electrostatic and π-π interactions. According to these results, H3PW12O40/Fe3O4/MIL-88A (Fe) can act as a reusable effective adsorbent for the fast elimination of tetracycline (TC), ciprofloxacin (CIP) and cationic dyes from aqueous solutions.

Adsorption of tetracycline by Nicandra physaloides (L.) Gaertn seed gum and Nicandra physaloides(L.) Gaertn seed gum/Carboxymethyl chitosan aerogel

In this study, novel aerogels of Nicandra physaloides (L.) Gaertn seed gum (NPG) and Nicandra physaloides (L.) Gaertn seed gum/Carboxymethyl chitosan (NPG/CMC) were prepared by freeze-drying method for removing tetracycline (TC) from water. Scanning electron microscope (SEM), X-ray diffraction (XRD),Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), and Brunauer-Emmett-Teller (BET) were used to characterize structure and morphology of NPG and NPG/CMC aerogels. The average pore diameter of NPG and NPG/CMC were 3.04 and 1.2 nm, the specific surface areas were 2.67 and 0.73 m²/g, respectively. The maximum adsorption capacity of NPG and NPG/CMC aerogels for TC based on Langmuir isotherm was 266.7 and 332.23 mg/g respectively. Through thermodynamic and kinetic studies, it was found that the adsorption processes of the two adsorbents were spontaneous and followed the pseudo-second-order kinetic model. And the process of NPG adsorption of TC was endothermic, while NPG/CMC was exothermic.

Visible-light driven dual heterojunction formed between g-C3N4/BiOCl@MXene-Ti3C2 for the effective degradation of tetracycline

In the present study, we have successfully formulated a dual heterojunction of g-C₃N₄/BiOCl@MXene-Ti₃C₂ (GCBM) which was found to be highly active in the visible region. GCBM was found to be highly efficient for the degradation of an antibiotic, tetracycline (TC) as compared to the individual constituting units; g-C₃N₄ and BiOCl. Maximum of 97% TC degradation rate was obtained within 90 min of visible light irradiation for initial concentration of 10 mg/L of TC. Optical analysis exhibited that the synthesized heterojunction showed high absorption in the complete spectrum. The reactive species specified by the scavenger study showed the major involvement of ^•O₂^- and ^•OH radicals. The charge transfer mechanism showed that 2 schemes were majorly involvement in which Z-scheme was formed between g-C₃N₄ and BiOCl and Schottky junction was formed between g-C₃N₄ and Mxene-Ti₃C₂. The formation of Schottky junction helped in inhibiting the back transfer of photogenerated charges and thus, helped in reducing the recombination rate. The synthesized photocatalyst was found to be highly reusable and was studied for consecutive 5 cycles that generalized the high proficiency even after repetitive cycles.

Effective Removal of Tetracycline from Water Using Copper Alginate @ Graphene Oxide with In-Situ Grown MOF-525 Composite: Synthesis, Characterization and Adsorption Mechanisms

For nanomaterials, such as GO and MOF-525, aggregation is the main reason limiting their adsorption performance. In this research, Alg-Cu@GO@MOF-525 was successfully synthesized by in-situ growth of MOF-525 on Alg-Cu@GO. By dispersing graphene oxide (GO) with copper alginate (Alg-Cu) with three-dimensional structure, MOF-525 was in-situ grown to reduce aggregation. The measured specific surface area of Alg-Cu@GO@MOF-525 was as high as 807.30 m²·g^-1, which is very favorable for adsorption. The synthesized material has affinity for a variety of pollutants, and its adsorption performance is significantly enhanced. In particular, tetracycline (TC) was selected as the target pollutant to study the adsorption behavior. The strong acid environment inhibited the adsorption, and the removal percentage reached 96.6% when pH was neutral. Temperature promoted the adsorption process, and 318 K adsorption performance was the best under experimental conditions. Meanwhile, 54.6% of TC could be removed in 38 min, and the maximum adsorption capacity reached 533 mg·g^-1, far higher than that of conventional adsorption materials. Kinetics and isotherms analysis show that the adsorption process accords with Sips model and pseudo-second-order model. Thermodynamic study further shows that the chemisorption is spontaneous and exothermic. In addition, pore-filling, complexation, π-π stack, hydrogen bond and chemisorption are considered to be the causes of adsorption.

Recyclable aminophenylboronic acid modified bacterial cellulose microspheres for tetracycline removal: Kinetic, equilibrium and adsorption performance studies for hoggery sewer

Significant concerns have been raised regarding to the pollution of antibiotics in recent years due to the abuse of antibiotics and their high detection rate in water. Herein, a novel super adsorbent, boronic acid-modified bacterial cellulose microspheres with a size of 415 μm in diameter was prepared through a facile water-in-oil emulsion method. The adsorbent was characterized by atomic force microscopy, scanning electron microscopy, and fourier transform infrared spectroscopy analyses to confirm its properties. The microspheres were applied as packing materials for the adsorption of tetracycline (TC) from an aqueous solution and hoggery sewer via the reversible covalent interaction between cis-diol groups in TC molecules and the boronic acid ligand. TC adsorption performance had been systemically investigated under various conditions, including the pH, temperature, TC concentration, contact time, and ionic strength. Results showed that the adsorption met pseudo-second-order, Elovich kinetic model and Sips, Redlich-Peterson isothermal models. And the adsorption process was spontaneous and endothermic, with the maximum TC adsorption capacity of 614.2 mg/g. After 18 adsorption-desorption cycles, the adsorption capacity remained as high as 84.5% compared with their original adsorption capacity. Compared with other reported adsorption materials, the microspheres had high adsorption capacity, a simple preparation process, and excellent recovery performance, demonstrating great potential in application on TC removal for water purification and providing new insights into the antibiotic's adsorption behavior of bacterial cellulose-based microspheres.

Adsorption of Methylene Blue from Aqueous Solution Using Gelatin-Based Carboxylic Acid-Functionalized Carbon Nanotubes@Metal–Organic Framework Composite Beads

Highlights

A new gelatin composite was used to remove methylene blue.

The adsorbent was composed of carbon nanotubes, a metal–organic framework and gelatin.

The adsorbent had a simple preparation process and was friendly to the environment.

The fixation of carbon nanomaterials with gelatin as the substrate avoided secondary pollution.

Using carbon nanotubes as the intermediate improved the adsorption capacity.

Abstract

A novel gelatin-based functionalized carbon nanotubes@metal–organic framework (F-CNTs@MOF@Gel) adsorbent was prepared by the green and simple method for the adsorption of methylene blue (MB). Cu-BTC (also known as HKUST-1) was selected as the MOF type. F-CNTs@Cu-BTC particles were fixed by gelatin, thus avoiding the secondary pollution of carbon nanomaterial particles to the environment. CNTs were used as the connecting skeleton to make more effective adsorption sites exposed on the surface of the internal pore structure of the adsorbent. In this paper, scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), powder X-ray diffraction (XRD), thermogravimetry (TGA) and BET analysis methods were used to characterize the new adsorbent. The effects of time, temperature, pH, dosage and initial concentration on the adsorption process were investigated by batch adsorption experiments. The adsorption mechanism was further analyzed by several commonly used kinetic and isotherm models, and the reliability of several fitting models was evaluated by the Akaike information criterion (AIC), Bayesian information criterion (BIC) and Hannan information criterion (HIC). After five regeneration experiments, the adsorbent still had 61.23% adsorption capacity. In general, the new adsorbent studied in this paper has an optimistic application prospect.

Wastewater Treatment by Polymeric Microspheres: A Review

This review addresses polymer microspheres used as adsorbent for wastewater treatment. The removal of various pollutants (including dyes, heavy metal ions, and organic pollutants) is a prominent issue, as they can cause severe health problems. Porous microspheres can provide large specific area and active sites for adsorption or photo degradation. Enhancement in performance is achieved by various modifications, such as the introduction of nanoparticles, magnetic particles, and ZIF-8. Some microspheres were synthesized from synthetic polymers such as vinylic polymer and polydopamine (PDA) through a facile fabrication process. Natural polymers (such as cellulose, alginate, and chitosan) that are biodegradable and eco-friendly are also used. The adsorbents used in industrial application require high adsorption capacity, thermal stability, and recyclability. Batch adsorption experiments were conducted to investigate the optimal conditions, influence of related factors, and adsorption capacities. Insights regarding the adsorption mechanisms were given from the kinetic model, isotherm model, and various characterization methods. The recyclability is investigated through regeneration ratio, or their maintenance of their capability through repeated adsorption-desorption cycles. The high potential of polymer microsphere for the removal of pollutants from wastewater is shown through the high adsorption capacities, environmentally friendliness, and high stability.

Strong adsorption properties and mechanism of action with regard to tetracycline adsorption of double-network polyvinyl alcohol-copper alginate gel beads

In the present study, glutaraldehyde was used as a hydrophobic modifier to crosslink polyvinyl alcohol (PVA), and copper ion was immobilized by sodium alginate (SA). Polyvinyl alcohol-copper alginate (PVA-CA) gel beads were prepared by a one-step process, and were used to adsorb and remove tetracycline (TC) from an aqueous solution. The beads were characterized by scanning electron microscopy (SEM), thermogravimetric analysis (TGA), Brunauer-Emmett-Teller (BET) measurement, X-ray diffraction (XRD), energy dispersive spectroscopy (EDS), and Fourier transform infrared spectroscopy (FTIR). The adsorption experiment showed that the optimal pH value of the beads was 5, and that their adsorption met pseudo-second-order kinetic and Langmuir isothermal models. The adsorption thermodynamics experiment showed that the adsorption process was spontaneous and endothermic. Under optimal adsorption conditions, the maximum adsorption capacity for TC of the beads was 231.431 mg/g, which was much higher than that of a single copper alginate matrix. After 5 adsorption-desorption cycles, the adsorption capacity remained high. FTIR and X-ray photoelectron spectroscopy (XPS) revealed that the cation bonding bridge reaction was the main driving force behind the adsorption mechanism. Compared with other reported adsorption materials, the PVA-CA gel beads have high adsorption capacity, a simple preparation process, and excellent recovery performance.

Efficient removal of tetracycline by a hierarchically porous ZIF-8 metal organic framework

Most reported metal organic frameworks (MOFs) have microporous structures and defective active sites, limiting their practical application to macromolecular substances. A hierarchical porous zeolitic imidazolate framework-8 (ZIF-8) was prepared using poly(diallyldimethylammonium chloride) (PDDA) as a structure-directing agent under facile "aqueous room-temperature" conditions to increase the mass transfer and adsorption capacity tetracycline hydrochloride (TCH). The ZIF-8 pore structure and morphology were synchronously tuned by controlling the PDDA molecular weight and dosage. Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), Bruner-Emmett-Teller (BET), scanning electron microscopy (SEM), NH₃-temperature-programmed desorption (NH₃-TPD) and adsorption results revealed abundant pore structures and open metal sites in the prepared materials, along with excellent TCH adsorption performance compared with ZIF-8, despite decreased BET surface areas. Initial screens revealed large adsorption capacities of hierarchical porous ZIF-8P3(4) (976.8 mg g^-1) due to the presence of more abundant unsaturated metal sites than ZIF-8 and novel hierarchical porous structures. Therefore, TCH adsorption on ZIF-8 and ZIF-8P3(4), including the kinetics, isotherms, thermodynamics and pH effect, was studied. The adsorption process follows pseudo-second-order kinetics and the Freundlich models better, indicating multilayer adsorption of TCH on the surface of the two absorbents. Adsorption behavior test, FTIR, XPS, BET and XRD results show that TCH adsorption on ZIF-8 and ZIF-8P3(4) most likely involves coordination bonds, electrostatic and π-π interactions, hydrogen bonds, and pore-filling effects. This study provides new insights into the template preparation of MOFs with high adsorption performance as potentially economical adsorbents to remove organic matter from contaminated water.

Efficient Adsorption of Tetracycline from Aqueous Solutions by Modified Alginate Beads after the Removal of Cu(II) Ions

This work dealt with a potential and effective method to reuse modified alginate beads after the removal of Cu(II) ions for efficient adsorption of tetracycline (TC) from aqueous solutions. The modified alginate beads were fabricated by a polyacrylamide (PAM) network interpenetrated in alginate-Ca2+ network (PAM/CA) decorated with polyethylene glycol as a pore-forming agent. The porous PAM/CA was characterized using scanning electron microscopy, Brunauer-Emmett-Teller, Fourier transform infrared spectroscopy, and X-ray photoelectron spectroscopy analysis. The adsorption kinetics, isotherms, adsorption stability, and reusability studies of the adsorbent toward Cu(II) ions were scrutinized. The column performance of porous PAM/CA was tested with Cu(II)-containing electroplating wastewater. After Cu(II) adsorption, the Cu(II)-adsorbed PAM/CA (PAM/CA@Cu) was applied to remove TC from aqueous solutions without any regeneration process. The effects of pH, initial TC concentration, ionic strength, and coexisting ions on the adsorption were also discussed in detail. Compared with many reported adsorbents, the PAM/CA@Cu exhibited an excellent adsorption performance toward TC with a maximum adsorption capacity of 356.57 mg/g predicted by the Langmuir model at pH 5.0 and 30 °C with the absence of coexisting ions. The possible adsorption mechanism of TC onto the PAM/CA@Cu was revealed.

Interaction between tetracycline and microorganisms during wastewater treatment: A review

Tetracycline (TC) is a commonly used human and veterinary antibiotic that is mostly discharged into wastewater in the form of the parent compounds. At present, wastewater treatment plants (WWTPs) use activated sludge processes that are not specifically designed to remove such pollutants. Considering the biological toxicity of TC in aquatic environment, the migration and fate of TC in the process of wastewater treatment deserve attention. This paper reviews the influence of TC on the functional bacteria in the sludge matrix and the development of tetracycline-resistant genes, and also discusses their adsorption removal rates, their adsorption kinetics and adsorption isotherm models, and infers their adsorption mechanism. In addition, the biodegradation of TC in the process of biological treatment is reviewed. Co-metabolism and the role of dominant bacteria in the degradation process are described, along with the formation of degradation byproducts and their toxicity. Furthermore, the current popular integrated coupling-system for TC degradation is also introduced. This paper systematically introduces the interaction between TC and activated sludge in WWTPs. The review concludes by providing directions to address research and knowledge gaps in TC removal from wastewater.

Prediction and optimization of adsorption properties for Cs+on NiSiO@NiAlFe LDHs hollow spheres from aqueous solution: Kinetics, isotherms, and BBD model

In this work, novel NiSiO@NiAlFe layered double hydroxides (LDHs) hollow spheres were prepared by hydrothermal method. It was worth noting that LDHs' grafting towards NiSiO hollow spheres could avoid the LDHs' aggregation, and thus enhanced the material's adsorption capacity. Furthermore, adsorption kinetics, adsorption isotherms, and Box-Behnken Design (BBD) model were conducted. Results indicated that NiSiO@NiAlFe LDHs hollow spheres had sufficient adsorption capability towards Cs⁺. The adsorption kinetics satisfied the pseudo-second-order adsorption model, Temkin model and Langmuir isotherm model. The adsorption process was efficient at the alkaline condition (pH = 10). The adsorption kinetics indicated that the adsorption process could reach the equilibrium in only 20 min. The maximum adsorption capacity of Cs⁺ towards NiSiO@NiAlFe LDHs hollow spheres was estimated to be 61.5 mg g^-1. Moreover, the adsorption thermodynamics indicated that the adsorption process was exothermal, feasible and spontaneous. Thus, NiSiO@NiAlFe LDHs hollow spheres presented a broad potential for treating cesium containing wastewater.

Fabricating acid-sensitive controlled PAA@Ag/AgCl/CN photocatalyst with reversible photocatalytic activity transformation

Achieving the intelligent controllability of the photocatalyst to the surrounding environment is a very meaningful work. Here, the polyacrylic acid (PAA) modified Ag/AgCl-40/CN composite was constructed to achieve an intelligent response of pH value. PAA exhibits hydrophilic properties at high pH value, increasing the adsorption capacity to tetracycline (TC) molecules. The morphology of PAA from contracted state to diastolic state, releasing the Ag/AgCl-40/CN catalyst. In addition, PAA modified Ag/AgCl-40/CN can prevent the loss of AgCl. The g-C₃N₄ nanosheets (CN) as a carrier enhance the dispersibility of the AgCl particles. The LSPR effects of Ag nanoparticles produce more electrons acting on photocatalytic degradation. On the results of experiment, the degradation of TC by PAA@Ag/AgCl-40/CN shows an excellent degradation activity when the high pH value. Photoluminescence spectroscopy and photocurrent demonstrate that carrier separation efficiency of PAA@Ag/AgCl-40/CN is higher than CN and Ag/AgCl-40/CN. The detection of the main active substances •O₂^- and h⁺, revealing a reasonable mechanism for the PAA@Ag/AgCl-40/CN hybrid system. This work provides a procedure to obtain smart materials that can switch photocatalytic processes.

Constructing CeO2/nitrogen-doped carbon quantum dot/g-C3N4 heterojunction photocatalysts for highly efficient visible light photocatalysis

Ternary CeO₂/nitrogen-doped carbon quantum dot (NCQD)/graphitic carbon nitride (g-C₃N₄) heterojunction nanocomposites were prepared by a high-temperature calcination and hydrothermal method and tested for degrading tetracycline (TC) and generating H₂. Compared with CeO₂ and g-C₃N₄, the Z-scheme CeO₂/NCQDs/g-C₃N₄ (CSNx, where x represents the amount of CeO₂ in wt%) nanoparticles showed a higher TC photodegradation capacity and H₂ evolution ability owing to enhanced efficient charge separation and photocatalytic stability. CSN5 showed the best photodegradation activity for TC degradation (100 mL, 20 mg L^-1; 100% degradation in 60 min; λ≥ 420 nm) and the highest H₂ evolution rate of 1275.42 μmol h^-1 g^-1 was approximately 3.73- and 32.25-times higher than those of pristine g-C₃N₄ (341.85 μmol h^-1 g^-1) and pure CeO₂ (39.55 μmol h^-1 g^-1), respectively. Superoxide (˙O₂^-) and hydroxyl (˙OH) radicals were also confirmed to be formed on the sample surface for TC photocatalytic degradation. As an electronic medium, NCQDs transferred electrons between the g-C₃N₄ and CeO₂ interface to promote the electron-hole separation. This work affords a helpful perspective for synthesizing efficient charge separation and environmentally friendly photocatalysts by controlling the surface heterostructure.

A strategy for the efficient removal of chlorophenols in petrochemical wastewater by organophilic and aminated silica@alginate microbeads: Taguchi optimization and isotherm modeling based on partition coefficient

Through in situ encapsulation of cetyltrimethylammonium bromide (CTAB) and urea-functionalized SiO₂ nanoparticles in alginate hydrogel, two types of new functionalized microbeads, CTAB-SiO₂@alginate (organophilic) and urea-SiO₂@alginate (aminated), were produced. Their adsorption behavior toward multiple chlorophenols (CPs: e.g., 4-chlorophenol (MCP), 2,4-dichlorophenol (DCP), and 2,4,6-trichlorophenol (TCP)) in petrochemical wastewater was assessed with the aid of Taguchi's L9 orthogonal array at three levels. In terms of the partition coefficient (PC: μmol/g·μM (or L/g)), the use of three-parameter models (hybrid Langmuir-Freundlich and Redlich-Peterson) yielded the best fit (R² ≈ 1). Furthermore, the performance evaluation in terms of PC metric indicated that CTAB-SiO₂@alginate (7.85 L/g) was better to treat total CPs than urea-modified SiO₂@alginate microbeads (3.83 L/g). The enhanced performance of the former reflects the significant contribution of CTAB functionality (sp² carbon tail and quaternary amine (N⁺) cationic head sites) for accelerating uptake of molecular (or suspended) and ionizable CPs molecules (e.g., with the aid of salting-out effect at a high initial CPs concentration and salinity) via hydrophobic/electrostatic interactions. The high performance of the CTAB-SiO₂@alginate was demonstrated against petroleum hydrocarbons, CPs, and phenol contaminants using real petrochemical wastewater (up to three reusable cycles).

Bio-inspired, high, and fast adsorption of tetracycline from aqueous media using Fe3O4-g-CN@PEI-β-CD nanocomposite: Modeling by response surface methodology (RSM), boosted regression tree (BRT), and general regression neural network (GRNN)

Because antibiotic-containing wastewaters are able to contaminate all environmental matrices (e.g. water bodies, soil, etc.), a special attention should be paid on developing appropriate materials for their remediation. Herein, the novel nanocomposite (NC) of Fe₃O₄-g-CN@PEI-β-CD was synthesized and employed effectively for the adsorptive removal of tetracycline (TC), the second most produced and employed antibiotic around the world. The successful fabrication of the nanocomposite with a high specific surface area (57.12 m²/g) was confirmed using XRD, SEM, TEM, FTIR, TGA, EDX, and BET analyses. The Fe₃O₄-g-CN@PEI-β-CD NC exhibited fast adsorption rates towards TC and maximum adsorption capacity on the basis of the Langmuir model reached 833.33 mg g^-1, much higher than that reported by different carbon- and/or nano-based materials. The adsorption process was modeled using the approaches of central composite design (CCD), boosted regression tree (BRT), and general regression neural network (GRNN) under various operational conditions of initial TC concentration, pH, adsorbent dose, tempreature, and time. The comparison of the models indicated good predictions of all, however, the BRT model was more accurate compared to the others, with R² = 0.9992, RMSE = 0.0026, MAE = 0.0014, and AAD = 0.0028, proving that it is a powerful approach for modeling TC adsorption by Fe₃O₄-g-CN@PEI-β-CD nanocomposite. The results showed that the order of the variables' effectiveness is as follow: pH > dose > TC concentration. The high adsorption capacity along with high efficiency (98 % in the optimized conditions by GA) ensures the potential of the as-prepared nanocomposite for in situ remediation of antibiotic-containing wastewaters.

Removal of Ciprofloxacin with Aluminum-Pillared Kaolin Sodium Alginate Beads (CA-Al-KABs): Kinetics, Isotherms, and BBD Model

In recent years, the problem of water pollution caused by antibiotics has attracted wide attention. The common use of antibiotics represents a threat to both human health and environmental safety. The modification of kaolin clay is promising due to its high efficiency, easy operation, and low cost. In this study, a novel material, aluminum-pillared kaolin sodium alginate beads (CA-Al-KABs), was synthesized by gelling and solidification processes. The structure and chemical properties were characterized by various analytical methods. The influencing factors (such as adsorbent dosage, contacting time, pH, ion strength, temperature, and initial concentration) and adsorption mechanism of ciprofloxacin (CIP) were studied. Furthermore, adsorption kinetics, adsorption isotherms, and a Box–Behnken design (BBD) model were conducted. Moreover, CA-Al-KABs’ adsorption efficiency towards other antibiotics were also evaluated. The adsorption experiments showed that the acidic environment (pH = 4) was more favorable for the adsorption of ciprofloxacin. The adsorption kinetics of ciprofloxacin by CA-Al-KABs microspheres were confirmed to be more suitable with the pseudo-first-order kinetics model. The Langmuir isotherm model showed that the maximum adsorption capacity of CA-Al-KABs microspheres to ciprofloxacin was 68.36 mg/g at 308.15 K. The adsorption driving force of CIP near CA-Al-KABs may be the electrostatic attraction. Further, CIP could also form complexes with Ca2+ and Al—Al—OH on CA-Al-KABs, and thus CIP was attracted to the adsorbent. Adsorption thermodynamics showed that the adsorption process was exothermic, feasible, and spontaneous. In addition, the adsorption performance on other antibiotics indicated CA-Al-KABs’ broad application in the treatment of antibiotic wastewater.

Fabrication of detonation nanodiamond@sodium alginate hydrogel beads and their performance in sunlight-triggered water release

Agricultural water use accounts for around 70% of total water use in the world. Enhancing agricultural water use efficiency is a key way to cope with water shortage. Here, sunlight-responsive hydrogel beads consisting of sodium alginate (SA) matrix and detonation nanodiamond (DND) were fabricated by an ion gelation technique, which has potential applications in controlled water release. The interaction between the DND and SA matrix was investigated by Fourier transform infrared (FTIR) spectra and X-ray diffraction (XRD). UV-vis diffuse reflectance spectra verified DND can absorb solar energy in the UV, visible and even near-infrared regions. DND dispersed in the hydrogel matrix can absorb sunlight and generate heat, increasing the temperature of the matrix and resulting in slow release of water from the elastic beads. In addition, the effects of DND content and pH were systematically studied to evaluate their water adsorption properties. The swelling kinetics of DND@SA hydrogel beads in distilled water could be fitted well with a pseudo-second-order kinetic model. Six consecutive cycles of water release-reswelling indicated that their easy regeneration and reusability. The novel and eco-friendly hydrogel beads should be applicable to on-demand, sequential, and long-term release of water via light exposure.