Adsorption of Pb(II) from water by treatment with an O-hydroxyphenyl thiourea-modified chitosan

Design of composite chitosan/algae/zeolite by freeze- or air-drying: A comparative adsorbent analysis for optimized removal of brilliant green dye

A bio-composite material was developed that contains chitosan, food-grade algae, and zeolite for the removal of brilliant green (BG) dye. The synthesized bio-composite was dried via two different methods (air-drying; AD, and freeze-drying; FD). The physicochemical characterization of air-dried chitosan-algae-zeolite (Cs-Alg-Zl-AD) and freeze-dried chitosan-algae-zeolite (Cs-Alg-Zl-FD) were investigated by spectroscopy (FTIR, SEM-EDX, and XPS), diffraction (XRD), surface charge via pHpzc, specific surface area (SSA) and elemental analyses. The utilization of Box-Behnken Design (BBD) was intended to optimize the three input variables, which are adsorbent dosage, pH of medium, and contact time. The adsorption optimization process yielded optimal conditions, which were verified through a desirability test and implemented in batch-mode equilibrium experiments. The Cs-Alg-Zl-FD has a higher specific surface area (SSA = 3.29 m2/g) compared to Cs-Alg-Zl-AD (SSA = 1.79 m2/g). The Cs-Alg-Zl-FD shows greater adsorptive removal of BG (98.6 %) over Cs-Alg-Zl-AD (88.6 %), in parallel agreement with differences in the SSA. Moreover, the maximum BG dye adsorption capacities of Cs-Alg-Zl-FD (119.5 mg/g) and Cs-Alg-Zl-AD (108 mg/g) at pH = 8.1 and 25 °C. The Freundlich model fits best with Cs-Alg-Zl-AD while Langmuir and Temkin models account for the Cs-Alg-Zl-FD dye adsorption. The Cs-Alg-Zl-FD shows greater dye adsorption over four adsorption cycles, as compared with the Cs-Alg-Zl-AD.

Recent advances in modifications, biotechnology, and biomedical applications of chitosan-based materials: A review

Chitosan, a natural polysaccharide with recognized biocompatibility, non-toxicity, and cost-effectiveness, is primarily sourced from crustacean exoskeletons. Its inherent limitations such as poor water solubility, low thermal stability, and inadequate mechanical strength have hindered its widespread application. However, through modifications, chitosan can exhibit enhanced properties such as water solubility, antibacterial and antioxidant activities, adsorption capacity, and film-forming ability, opening up avenues for diverse applications. Despite these advancements, realizing the full potential of modified chitosan remains a challenge across various fields. The purpose of this review article is to conduct a comprehensive evaluation of the chemical modification techniques of chitosan and their applications in biotechnology and biomedical fields. It aims to overcome the inherent limitations of chitosan, such as low water solubility, poor thermal stability, and inadequate mechanical strength, thereby expanding its application potential across various domains. This review is structured into two main sections. The first part delves into the latest chemical modification techniques for chitosan derivatives, encompassing quaternization, Schiff base formation, acylation, carboxylation, and alkylation reactions. The second part provides an overview of the applications of chitosan and its derivatives in biotechnology and biomedicine, spanning areas such as wastewater treatment, the textile and food industries, agriculture, antibacterial and antiviral activities, drug delivery systems, wound dressings, dental materials, and tissue engineering. Additionally, the review discusses the challenges associated with these modifications and offers insights into potential future developments in chitosan-based materials. This review is anticipated to offer theoretical insights and practical guidance to scientists engaged in biotechnology and biomedical research.

The remediation potential and kinetics of Pb2+ adsorbed by the organic frameworks of Cladophora rupestris

Cladophora rupestris is ubiquitous in many kinds of waterbodies, and C. rupestris biomass can serve as a carrier for adsorbing and transferring heavy metals. Batch experiments and characterization were performed. Results showed that the organic frameworks of C. rupestris (CROF) had a specific surface area of 2.58 m2/g and an external surface area of 2.06 m2/g. Many mesopores were present in CROF, mainly distributed in 2.5-7.5 nm. The zeta potentials were within the range of - 4.46 to - 13.98 mV in the tested pH of 2.0-9.0. CROF could effectively adsorb Pb2+ in large pH range. The maximum adsorption capacity (qmax) of Pb2+ on CROF was 15.02 mg/g, and 97% of Pb2+ was adsorbed onto CROF after 25 min. CROF had a preferential adsorption of Pb2+. The protein secondary structures and carbon skeletons of CROF all worked in adsorption. The main Pb2+ adsorption mechanisms were pore filling, electrostatic attraction, Pb-π interaction, and surface complexation. Therefore, it is valuable as a biosorbent for the removal of Pb2+ from waterbodies.

DOTA functionalized adsorbent DOTA@Sludge@Chitosan derived from recycled shrimp shells and sludge and its application for lead and chromium removal from water

DOTA@Sludge@Chitosan was synthesized by a facile treatment using DOTA (1,4,7,10-tetraazacyclododecane-N,N',N,N'-tetraacetic acid) to modify dry sludge and chitosan in an acidic solution. The performance of developed DOTA@Sludge@Chitosan was investigated for the adsorptive removal of Cr6+ and Pb2+ from water. Characterization studies showed that the materials possess a large surface area (52.009 m2/g), pore volume (0.069 cm3/g), and abundant functional groups of amino and hydroxyl. The prepared material showed a synergetic effect due to carboxylic acid and sludge, effectively removing Cr6+ and Pb2+. It reached 329.4 mg/g (Pb2+) and 273.3 mg/g (Cr6+) at 20 °C, much higher than commercial activated carbon. The regeneration of the adsorbent was tested for six adsorption and desorption cycles. The results demonstrate that the DOTA@Sludge@Chitosan adsorbent well-maintained high adsorption capacity attributed to its stability, making it a promising adsorbent for heavy metals removal from industrial effluent.

Molecular dynamics simulations of the solubility and conformation change of chitosan grafted polyacrylamide: Impact of grafting rate

Graft modification is an effective approach to improve the water solubility and molecular weight of chitosan. This work investigated the effect of grafting rate on water solubility of chitosan-grafted polyacrylamide (Chi-g-PAM) using molecular dynamics simulations. The intramolecular and intermolecular interaction between Chi-g-PAM with the grafting rate of 100%-250% and water together with the conformation change were analyzed by radial distribution function (RDF), radius of gyration, solvation free energy (ΔGSFE), mean square displacement, diffusion coefficient and shear viscosity. The results showed that the intramolecular hydrogen bonding of Chi-g-PAM was the dominant factor affecting its water solubility. While the grafting rate of Chi-g-PAM increased from 100% to 250%, the RDF of Chi-g-PAM decreased from 5.39 to 3.57 between O-H at 2.0 Å and 2.60 to 1.30 between N-H at 2.1 Å. The interaction between Chi-g-PAM and water increased with grafting rate as the absolute value of ΔGSFE for Chi-g-PAM increased from 432.917 kcal/mol to 858.749 kcal/mol. The solubility of Chi-g-PAM in acidic solution was much better than that of Chi-g-PAM in aqueous solution. Our work on the fundamental insights into the effect of grafted molecular structure of chitosan-based copolymer on its solubility will benefit the development of environmentally friendly chitosan-based flocculants.

Selective removal of Pb(II) from yellow rice wine using magnetic carbon-based adsorbent

BACKGROUND

The non-distilled property and prolonged production period of yellow rice wine have significantly increased the metal residue problem, posing a threat to human health. In this study, a magnetic carbon-based adsorbent, named magnetic nitrogen-doped carbon (M-NC), was developed for the selective removal of lead(II) (Pb(II)) from yellow rice wine.

RESULTS

The results showed that the uniformly structured M-NC could be easily separated from the solution, exhibiting a high Pb(II) adsorption capacity of 121.86 mg g-1 . The proposed adsorption treatment showed significant Pb(II) removal efficiencies (91.42-98.90%) for yellow rice wines in 15 min without affecting their taste, odor, and physicochemical characteristics of the wines. The adsorption mechanism studied by X-ray photoelectron spectroscopy (XPS) and Fourier-transform infrared (FTIR) analyses indicated that the selective removal of Pb(II) could be attributed to the electrostatic interaction and covalent interaction between the empty orbital of Pb(II) and the π electrons of the N species on M-NC. Additionally, the M-NC showed no significant cytotoxicity on the Caco-2 cell lines.

CONCLUSION

Selective removal of Pb(II) from yellow rice wine was achieved using magnetic carbon-based adsorbent. This facile and recyclable adsorption operation could potentially address the challenge of toxic metal pollution in liquid foods. © 2023 Society of Chemical Industry.

Dielectric barrier discharge plasma-modified chitosan flocculant and its flocculation performance

The flocculation performance of chitosan can be enhanced by grafting modification to overcome its disadvantages of poor water solubility. In this study, chitosan was modified by dielectric barrier discharge plasma and polymerized with acrylamide and aluminum chloride to synthesize a new chitosan-based flocculant, namely, chitosan-acrylamide-aluminum chloride (CA-PAC). After optimizing the synthesis conditions of CA-PAC, the best conditions were as follows: discharge time of 3 min, discharge power of 50 W, polymerization temperature of 60 °C, polymerization time of 3 h, total monomer concentration of 100 g/L, and m(AlCl3):m(CA) ratio of 2:1. Characterization was performed through SEM, XPS, FTIR, XRD, TG and 1H NMR. Results showed that the preparation of CA-PAC was successful. The influences of flocculant dosage, pH, and stirring intensity on flocculation efficiency were investigated. The removal efficiency of turbidity was 94.1 %. The investigation of the flocculation mechanism revealed that CA-PAC mainly relied on charge neutralization or the synergic action of electric neutralization, bridging, and roll-sweep under acidic and neutral conditions, but it depended on the joint action of adsorption bridging and net sweeping under alkaline conditions. This study provides new ideas for the preparation and development of modified chitosan and broadens its application in water treatment.

Selective adsorption of tetracycline and copper(II) on ion-imprinted porous alginate microspheres: performance and potential mechanisms

A novel epichlorohydrin and thiourea grafted porous alginate adsorbent (UA-Ca/IIP) was synthesized using ion-imprinting and direct templating to remove copper ions (Cu(II)) and tetracycline (TC) in aqueous solution. UA-Ca/IIP demonstrated great selectivity for Cu(II) and TC among different coexisting anions (CO32-, PO43- and SO42-), cations (Ca2+, Mg2+ and NH4+), and antibiotics (oxytetracycline and sulfamethoxazole). The adsorption of TC and Cu(II) by UA-Ca/IIP was significantly affected by the pH of the solution, and the quantity of TC and Cu(II) adsorbed reached a maximum at pH 5. A pseudo-second-order model better fitted the kinetic data; the Langmuir model predicted the maximum adsorption quantities 3.527 mmol TC g-1 and 4.478 mmol Cu(II) g-1 at 298 K. Thermodynamic studies indicated that the TC and Cu(II) adsorption was more rapid at a higher temperature. Antagonistic and synergistic adsorption experiments showed that the adsorption capacity of TC would increase significantly with the increase of Cu(II) concentration. Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy indicated that along with the influence of pH, electrostatic interaction and complexation were the main mechanisms of TC and Cu(II) adsorption. Regeneration experiments revealed that TC and Cu(II) were removed efficiently and that UA-Ca/IIP was recyclable over the long term. These results show that the modified porous alginate microsphere is a green and recyclable adsorbent, which has good selectivity and high adsorption performance for the removal of TC and Cu(II).

Progress in preparation and properties of chitosan-based hydrogels

Chitosan is a kind of natural polysaccharide biomass with the second highest content in nature after cellulose, which has good biological properties such as biocompatibility, biodegradability, hemostasis, mucosal adsorption, non-toxicity, and antibacterial properties. Therefore, hydrogels prepared from chitosan have the advantages of good hydrophilicity, unique three-dimensional network structure, and good biocompatibility, so they have received extensive attention and research in environmental testing, adsorption, medical materials, and catalytic supports. Compared with traditional polymer hydrogels, biomass chitosan-based hydrogels have advantages such as low toxicity, excellent biocompatibility, outstanding processability, and low cost. This paper reviews the preparation of various chitosan-based hydrogels using chitosan as raw material and their applications in the fields of medical materials, environmental detection, catalytic carriers, and adsorption. Some views and prospects are put forward for the future research and development of chitosan-based hydrogels, and it is believed that chitosan-based hydrogels will be able to obtain more valuable applications.

Chitosan-based composite hydrogel with a rigid-in-flexible network structure for pH-universal ultra-efficient removal of dye

Polysaccharide-based hydrogel adsorbents become popular because of their high adsorption capacity and fast adsorption rate, but their low removal rate and poor pH resistance have always been fatal shortcomings. Herein, a feasible strategy was proposed to strengthen the ability of hydrogel adsorbent to remove organic pollutants (i.e., dye) by incorporating natural rectorite (REC) into chitosan-g-poly (2-acrylamido-2-methyl-propane-sulfonic-acid) hydrogel network to form a rectorite-in-polymer network structure. The introduction of less dosage of REC (1.2 wt%) into the hydrogel facilitates to improve its adsorption capacities toward methylene blue (MB) in deionized water, tap water, seawater, Yangtze River water, and Yellow River water (1083.39-1303.49 mg/g); while incorporating higher content of REC (15.8 wt% REC) helps to improve the removal rate (99.6 % for MB in real waters), which are greatly superior to commercial activated carbons. The adsorbent keeps high adsorption efficiency in a broad pH range (2-11), and can be reused for >4 times.

Synthesis of Xanthan Gum Anchored α-Fe2O3 Bionanocomposite Material for Remediation of Pb (II) Contaminated Aquatic System

Increases in community and industrial activities have led to disturbances of the environmental balance and the contamination of water systems through the introduction of organic and inorganic pollutants. Among the various inorganic pollutants, Pb (II) is one of the heavy metals possessing non-biodegradable and the most toxic characteristics towards human health and the environment. The present study is focussed on the synthesis of efficient and eco-friendly adsorbent material that can remove Pb (II) from wastewater. A green functional nanocomposite material based on the immobilization of α-Fe₂O₃ nanoparticles with xanthan gum (XG) biopolymer has been synthesized in this study to be applied as an adsorbent (XGFO) for sequestration of Pb (II). Spectroscopic techniques such as scanning electron microscopy with energy dispersive X-ray (SEM-EDX), Fourier transform infrared (FTIR), transmission electron microscopy (TEM), X-ray diffraction (XRD), ultraviolet visible (UV-Vis) and X-ray photoelectron spectroscopy (XPS) were adopted for characterizing the solid powder material. The synthesized material was found to be rich in key functional groups such as -COOH and -OH playing important roles in binding the adsorbate particles through ligand-to-metal charge transfer (LMCT). Based on the preliminary results, adsorption experiments were conducted, and the data obtained were applied to four different adsorption isotherm models, viz the Langmuir, Temkin, Freundlich and D-R models. Based on the high values of R² and low values of χ², the Langmuir isotherm model was found to be the best model for simulation of data for Pb (II) adsorption by XGFO. The value of maximum monolayer adsorption capacity (Q_m) was found to be 117.45 mg g^-1 at 303 K, 126.23 mg g^-1 at 313 K, 145.12 mg g^-1 at 323 K and 191.27 mg g^-1 at 323 K. The kinetics of the adsorption process of Pb (II) by XGFO was best defined by the pseudo-second-order model. The thermodynamic aspect of the reaction suggested that the reaction is endothermic and spontaneous. The outcomes proved that XGFO can be utilized as an efficient adsorbent material for the treatment of contaminated wastewater.

Multicomponent adsorption of heavy metals onto biogenic hydroxyapatite: Surface functional groups and inorganic mineral facilitating stable adsorption of Pb(Ⅱ)

Due to the coexistence of various heavy metals in the contaminated environment, it is essential to comprehensively study the multicomponent adsorption of heavy metals in order to tackle these combined pollutants. Herein, the adsorption processes of Pb(Ⅱ), Cu(Ⅱ) and Cd(Ⅱ) by biogenic hydroxyapatite (BHAp) were investigated in single and multicomponent systems. The maximum adsorption capacity for Pb(Ⅱ), Cu(Ⅱ) and Cd(Ⅱ) by BHAp in single system reached 311.16, 82.05 and 92.54 mg g^-1, respectively, while adsorption capacity for Cu(Ⅱ) and Cd(Ⅱ) in multicomponent system decreased more obviously than that of Pb(Ⅱ). Furthermore, the stability of Cu(Ⅱ) and Cd(Ⅱ) adsorbed on BHAp was indeed influenced in multicomponent system. By means of the characterization analysis, it was found that ion exchange was more instrumental in the adsorption processes of Cu(Ⅱ) and Cd(Ⅱ) in single system than in multicomponent system. Significantly, it was observed that the proportion of generally stable Pb(II) adsorbed on BHAp exceeded 95% in both single and multicomponent systems. This result might be due to the in-site growth of stable crystals of Pb_xCa_10-x(PO₄)₆(OH)₂, which was synergistically induced by surface functional groups and inorganic mineral of BHAp, and was unaffected by the coexistence of Cu(Ⅱ) and Cd(Ⅱ).

Design of Zr-MOFs by Introducing Multiple Ligands for Efficient and Selective Capturing of Pb(II) from Aqueous Solutions

The existence of lead ions seriously affects the quality of many metal products in metallurgical enterprises. Currently, the various methods of lead-ion removal tried by researchers will affect valuable metals in the removal process, thus resulting in low economic efficiency. In this study, a novel metal-organic framework adsorbent (UiO-FHD) which efficiently and selectively captures lead ions is developed by introducing multiple ligands. The maximum adsorption capacity of lead ions is 433.15 mg/g at pH 5. The adsorption process accords with the pseudo-second-order kinetic and the Langmuir isotherm models at room temperature. Thermodynamic experiments indicate that the removal of Pb(II) is facilitated by appropriate temperature reduction. The performance tests indicate that UiO-FHD maintains a high removal rate of 90.35% for Pb(II) after four consecutive adsorption-desorption cycles. The distribution coefficient of lead ions (26.7 L/g) shows that UiO-FHD has excellent selective adsorption for lead ions. It is revealed that the chelation of the sulfhydryl groups and the electrostatic interaction of the hydroxyl groups are the dominant factors to improve the removal rate of Pb(II) by density functional theory calculations. This study clarifies the value of self-designed novel organic ligands in metal-organic framework materials that selectively capture heavy-metal ions.