Dip- and Spray-coating of Schanz pin with PLA and PLA nanosphere for prolonged antibacterial activity

A Study of PLA Thin Film on SS 316L Coronary Stents Using a Dip Coating Technique

The dip coating process is one of the recognized techniques used to generate polymeric coatings on stents in an easy and low-cost way. However, there is a lack of information about the influence of the process parameters of this technique on complex geometries such as stents. This paper studies the dip coating process parameters used to provide a uniform coating of PLA with a 4-10 µm thickness. A stainless-steel tube (AISI 316L) was laser-cut, electropolished, and dip-coated in a polylactic acid (PLA) solution whilst changing the process parameters. The samples were characterized to examine the coating's uniformity, thickness, surface roughness, weight, and chemical composition. FTIR and Raman investigations indicated the presence of PLA on the stent's surface, the chemical stability of PLA during the coating process, and the absence of residual chloroform in the coatings. Additionally, the water contact angle was measured to determine the hydrophilicity of the coating. Our results indicate that, when using entry and withdrawal speeds of 500 mm min-1 and a 15 s immersion time, a uniform coating thickness was achieved throughout the tube and in the stent with an average thickness of 7.8 µm.

Antibiotic impregnation and nanocoating of external ventricular drainage catheters for antibacterial applications: Evaluation of in vitro studies and molecular docking

The most suitable method to treat hydrocephalus disease is to insert a shunt catheter that drains the cerebral spinal fluid (CSF); however, shunt implantation is often associated with various bacterial infections. In this study, antibiotic-loaded nanospheres were prepared using the solvent evaporation technique and coated on an antibiotic-impregnated shunt surface to promote shunt antibacterial properties. Clindamycin (CDM) and rifampicin (RIF) were in combination loaded in a single nanosphere, whereas trimethoprim (TMP) was loaded individually in triblock copolymers [(d,l-lactide-random-ε-caprolactone)-block-poly(ethylene glycol)-block-(d,l-lactide-random-ε-caprolactone)] (PLEC). The drug-loading content, encapsulation efficiency, yield, size, and zeta potential of the antibiotic-loaded nanospheres were measured. The results showed that the drug-loading content of clindamycin- and rifampicin-loaded nanospheres (CDM/RIF-NPs) was approximately 3% and 8%, respectively, at a drug to polymer ratio of 1:2. In addition, trimethoprim-loaded nanospheres (TMP-NPs) showed nearly 7% drug loading at equal drug and polymer ratios. The amount of drug release was determined before and after the coating of nanospheres on the shunt surface. In addition, in silico molecular docking studies indicated the good chemical interaction of these antibiotics with PLEC, and the results were consistent with those of impregnation studies. Antibacterial tests of coated external ventricular drainage showed antibacterial activity for up to 21 days.

Overview of Antimicrobial Biodegradable Polyester-Based Formulations

As the clinical complications induced by microbial infections are known to have life-threatening side effects, conventional anti-infective therapy is necessary, but not sufficient to overcome these issues. Some of their limitations are connected to drug-related inefficiency or resistance and pathogen-related adaptive modifications. Therefore, there is an urgent need for advanced antimicrobials and antimicrobial devices. A challenging, yet successful route has been the development of new biostatic or biocide agents and biomaterials by considering the indisputable advantages of biopolymers. Polymers are attractive materials due to their physical and chemical properties, such as compositional and structural versatility, tunable reactivity, solubility and degradability, and mechanical and chemical tunability, together with their intrinsic biocompatibility and bioactivity, thus enabling the fabrication of effective pharmacologically active antimicrobial formulations. Besides representing protective or potentiating carriers for conventional drugs, biopolymers possess an impressive ability for conjugation or functionalization. These aspects are key for avoiding malicious side effects or providing targeted and triggered drug delivery (specific and selective cellular targeting), and generally to define their pharmacological efficacy. Moreover, biopolymers can be processed in different forms (particles, fibers, films, membranes, or scaffolds), which prove excellent candidates for modern anti-infective applications. This review contains an overview of antimicrobial polyester-based formulations, centered around the effect of the dimensionality over the properties of the material and the effect of the production route or post-processing actions.

Antibacterial and biocompatibility studies of triple antibiotics-impregnated external ventricular drainage: In vitro and in vivo evaluation

Hydrocephalus is a neurological disease caused by an unusually high level of cerebrospinal fluid (CSF), which can be relieved by external ventricular drainage (EVD) insertion. However, the infection can lead to complications during the use of EVD. In this study, EVD was impregnated with three synergistic antibiotics, including rifampicin, clindamycin, and trimethoprim, to improve the antibacterial property. The impregnated drainage was studied for its characteristics in vitro and in vivo. Drug loading determination revealed that rifampicin had the highest concentration in the tube, followed by clindamycin and trimethoprim, respectively. In vitro cytotoxicity and hemolytic studies showed no toxic effects from antibiotics-impregnated EVD on fibroblast and red blood cells. For antibacterial testing, the impregnated EVD exhibited antibacterial activity against Staphylococcus aureus MRSA and Staphylococcus epidermidis up to 14 and 90 days, respectively. Moreover, biocompatibility and drug release into the bloodstream and surrounding tissues were investigated by implantation in rabbits for 30 days. Histology and morphology results showed that fibroblast cells began to adhere to the drainage surface and inflammatory cell numbers were noticeably small after the long-term implantation. In addition, there was no drug leakage to the bloodstream and surrounding tissues. Hence, this impregnated EVD can potentially be used for antibacterial application.

Fabrication and in vitro characterization of zinc oxide nanoparticles and hyaluronic acid-containing carboxymethylcellulose gel for wound healing application

Chronic wounds, such as burns and diabetic ulcers, are complex wounds sustained by the skin that require life-long rehabilitation and have the potential to deteriorate and get infected. The number of patients with this ailment has been steadily increasing. This illness demands the use of new dressings with the best capabilities for managing wound healing. This study created an gel with carboxymethylcellulose (CMC), hyaluronic acid (HA), and zinc oxide nanoparticles (ZnO NPs). According to the findings, the manufacturing technique with a 1:4 ratio of HA and CMC gel had the best viscosity. Additionally, varying concentrations of zinc oxide nanoparticles (ZnO NPs) were added to the formula. Variations included 0.05, 0.125, 0.5, 1.0, 3.0, 5.0, and 10% by weight. In order to find the ideal dose and formulation, physical properties, an anti-bacterial test, and a cell migration assay were carried out. The samples with concentration of 0.5, 1.0, 3.0, 5.0 and 10% w/v showed ability to kill gram-positive and gram-negative bacteria. Wound healing experiments showed that cells proliferated for HA/CMC/ZnO gel with a weight-to-volume ratio of 0.05% and 1.0% w/v. In conclusion, according to all (physical and biological) characterization, the HA/CMC/ZnO gel with a weight-to-volume ratio of 1.0% w/v was found to have a considerable standard for wound-healing materials, demonstrating a promising effect against bacteria.