Investigation of an immobilization process for PFAS contaminated soils

Effectiveness of waste-derived MIL type MOFs in removing PFOA and PFAS pollutants for environmental remediation

Elimination of perfluorooctanoic acid (PFOA), a persistent pollutant that is toxic to human and ecosystem health, is important. In this study, three adsorbents, C-101, W-101, and NW-101, were evaluated. W-101 was modified by diamine ethyl modification to enhance the number of PFOA adsorption sites. The results showed that W-101 (42.7 mg g-1) had better PFOA adsorption capacity than C-101 (12.3 mg g-1), and NW-101 (698.4 mg g-1) was the best. The Langmuir model correctly described the isotherms of PFOA adsorption, and the pseudo-second-order kinetic model fitted the process. NW-101 exhibited an excellent adsorption efficiency, as it reached the equilibrium within 7 min, and also revealed higher reusability due to the stable structure of the amine-grafted structure; therefore, NW-101 proved very efficient in PFOA removal. The new method used the bark of poplar trees to prepare MIL-101(Cr) adsorbents with surface areas of 3341, 2767, and 2374 m2 g-1 for C-101, W-101, and NW-101, respectively. This cost-effective, eco-friendly method utilizes renewable raw materials, minimizes environmental impact, and represents a significant advance in PFOA removal and thermal material research.

Occurrence, transformation, and transport of PFAS entering, leaving, and flowing past wastewater treatment plants with diverse land uses

Per- and polyfluoroalkyl substances (PFAS) have been detected ubiquitously throughout the environment. Wastewater treatment plants (WWTPs) have been identified as potential hotspots for the introduction of PFAS into the environment. Therefore, the occurrence, transformation, and transport of 18 PFAS in two WWTPs with varying treatment processes, prevailing land uses, and during two distinct time periods were investigated. Polar Organic Chemical Integrative Samplers (POCIS) were installed at two WWTPs in Central Kentucky during April and July of 2022. PFAS concentrations typically increased from influent to effluent at both WWTPs, regardless of wastewater treatment processes, but changes in surface water concentrations from upstream to downstream of the effluent mixing zones varied. Both WWTPs discharged the 18 PFAS at higher loads than received, indicating prevalent transformation of PFAS precursors and non-measured PFAS analytes into measurable PFAS. Nearly all measured PFAS persisted in aqueous (86-98%) compartments rather than sediment or biosolids (2-14%). All biosolids had low content of PFAS with the dominant compound being PFOS (1.59-2.60 ng/g). Based on recent US EPA proposed maximum contaminant levels, hazard indexes for drinking water were exceeded in effluent and downstream surface waters at both WWTPs. The WWTP located in a heavily developed area and downstream from a firefighting training facility, had significantly higher concentrations of most PFAS species at most monitoring sites and was less impacted by sampling period compared to the WWTP located in a moderately developed, pastured area. Findings support the importance of WWTPs and land use practices as contributing to PFAS impact to downstream ecosystems along with potentially increasing strains on downstream drinking water source waters in regions that are surface water dependent.

PFOA remediation from kaolinite soil by electrokinetic process coupled with activated carbon/iron coated activated carbon - permeable reactive barrier

This study applied electrokinetic (EK) in situ soil remediation for perfluorooctanoic acid (PFOA) removal from kaolinite soil. The kaolinite soil was spiked with 10 mg/kg PFOA for the EK treatment using Sodium Cholate bio-surfactant coupled with Activated Carbon (AC) or iron-coated Activated Carbon (FeAC) permeable reactive barrier (PRB). The study also evaluated the impact of AC and FeAC PRBs' position on the EK process performance. In the EK with the PRB in the middle section, PFOA removal from kaolinite was 52.35 % in the AC-EK tests and 59.55 % in the FeAC-EK. Experimental results showed the accumulation of PFOA near the cathode region in FeAC PRB tests, hypothesising that Fe from the PRB formed a complex with PFOA ions and transported it to the cathode region. Spent PRBs were regenerated with methanol for PFOA extraction and reuse in the EK experiments. Although FeAC PRB achieved better PFOA removal than AC PRB, the EK tests with regenerated AC-EK and FeAC-EK PRBs achieved 40.37 % and 20.62 % PFOA removal. For EK with FeAC PRB near the anode, PFOA removal was 21.96 %. Overall, using PRB in conjunction with the EK process can further enhance the removal efficiency. This concept could be applied to enhance the removal of various PFAS compounds from contaminated soils by combining a suitable PRB with the EK process. It also emphasizes the feasibility of in-situ soil remediation technologies for forever chemical treatment.

PFOA-contaminated soil remediation: a comprehensive review

Soil and groundwater contamination has been raised as a concern due to the capability of posing a risk to human health and ecology, especially in facing highly toxic and emerging pollutants. Because of the prevalent usage of perfluorooctanoic acid (PFOA), in industrial and production processes, and subsequently the extent of sites contaminated with these pollutants, cleaning up PFOA polluted sites is paramount. This research provides a review of remediation approaches that have been used, and nine remediation techniques were reviewed under physical, chemical, and biological approaches categorization. As the pollutant specifications, environmental implications, and adverse ecological effects of remediation procedures should be considered in the analysis and evaluation of remediation approaches, unlike previous research that considered a couple of PFAS pollutants and generally dealt with technical issues, in this study, the benefits, drawbacks, and possible environmental and ecological adverse effects of PFOA-contaminated site remediation also were discussed. In the end, in addition to providing sufficient and applicable understanding by comprehensively considering all aspects and field-scale challenges and obstacles, knowledge gaps have been found and discussed.

Aminated clay-polymer composite as soil amendment for stabilizing the short- and long-chain per- and poly-fluoroalkyl substances in contaminated soil

Soils contaminated with per- and poly- fluoroalkyl substances (PFAS) require immediate remediation to protect the surrounding environment and human health. A novel animated clay-polymer composite was developed by applying polyethyleneimine (PEI) solution onto a montmorillonite clay-chitosan polymer composite. The resulting product, PEI-modified montmorillonite chitosan beads (MMTCBs) were characterized as an adsorptive soil amendment for immobilizing PFAS contaminants. The MMTCBs exhibited good efficiency to adsorb the PFAS, showing adsorption capacities of 12.2, 16.7, 18.5, and 20.8 mg g-1 for PFBA, PFBS, PFOA, and PFOS, respectively, which were higher than those obtained by granular activated carbon (GAC) (i.e., an adsorbent used as a reference). Column leaching tests demonstrated that amending soil with 10% MMTCBs resulted in a substantial decrease in the leaching of PFOA, PFOS, PFBA, and PFBS by 90%, 100%, 64%, and 68%, respectively. These reductions were comparable to the values obtained for GAC-modified soil, particularly for long-chain PFAS. Incorporating MMTCBs into the soil not only preserved the structural integrity of the soil matrix but also enhanced its shear strength (kPa). Conversely, adding GAC to the soil resulted in a reduction of the soil's mechanical properties.

In vitro and in vivo remediation of per- and polyfluoroalkyl substances by processed and amended clays and activated carbon in soil

Remediation methods for soil contaminated with poly- and perfluoroalkyl substances (PFAS) are needed to prevent their leaching into drinking water sources and to protect living organisms in the surrounding environment. In this study, the efficacy of processed and amended clays and carbons as soil amendments to sequester PFAS and prevent leaching was assessed using PFAS-contaminated soil and validated using sensitive ecotoxicological bioassays. Four different soil matrices including quartz sand, clay loam soil, garden soil, and compost were spiked with 4 PFAS congeners (PFOA, PFOS, GenX, and PFBS) at 0.01-0.2 μg/mL and subjected to a 3-step extraction method to quantify the leachability of PFAS from each matrix. The multistep extraction method showed that PFAS leaching from soil was aligned with the total carbon content in soil, and the recovery was dependent on concentration of the PFAS. To prevent the leaching of PFAS, several sorbents including activated carbon (AC), calcium montmorillonite (CM), acid processed montmorillonite (APM), and organoclays modified with carnitine, choline, and chlorophyll were added to the four soil matrices at 0.5-4 % w/w, and PFAS was extracted using the LEAF method. Total PFAS bioavailability was reduced by 58-97 % by all sorbents in a dose-dependent manner, with AC being the most efficient sorbent with a reduction of 73-97 %. The water leachates and soil were tested for toxicity using an aquatic plant (Lemna minor) and a soil nematode (Caenorhabditis elegans), respectively, to validate the reduction in PFAS bioavailability. Growth parameters in both ecotoxicological models showed a dose-dependent reduction in toxicity with value-added growth promotion from the organoclays due to added nutrients. The kinetic studies at varying time intervals and varying pHs simulating acidic rain, fresh water, and brackish water suggested a stable sorption of PFAS on all sorbents that fit the pseudo-second-order for up to 21 days. Contaminated soil with higher than 0.1 μg/mL PFAS may require reapplication of soil amendments every 21 days. Overall, AC showed the highest sorption percentage of total PFAS from in vitro studies, while organoclays delivered higher protection in ecotoxicological models (in vivo). This study suggests that in situ immobilization with soil amendments can reduce PFAS leachates and their bioavailability to surrounding organisms. A combination of sorbents may facilitate the most effective remediation of complex soil matrices containing mixtures of PFAS and prevent leaching and uptake into plants.

PFAS remediation in soil: An evaluation of carbon-based materials for contaminant sequestration

The presence of per- and poly-fluoroalkyl substances (PFAS) in soils is a global concern as these emerging contaminants are highly resistant to degradation and cause adverse effects on human and environmental health at very low concentrations. Sequestering PFAS in soils using carbon-based materials is a low-cost and effective strategy to minimize pollutant bioavailability and exposure, and may offer potential long-term remediation of PFAS in the environment. This paper provides a comprehensive evaluation of current insights on sequestration of PFAS in soil using carbon-based sorbents. Hydrophobic effects originating from fluorinated carbon (C-F) backbone "tail" and electrostatic interactions deriving from functional groups on the molecules' "head" are the two driving forces governing PFAS sorption. Consequently, varying C-F chain lengths and polar functional groups significantly alter PFAS availability and leachability. Furthermore, matrix parameters such as soil organic matter, inorganic minerals, and pH significantly impact PFAS sequestration by sorbent amendments. Materials such as activated carbon, biochar, carbon nanotubes, and their composites are the primary C-based materials used for PFAS adsorption. Importantly, modifying the carbon structural and surface chemistry is essential for increasing the active sorption sites and for strengthening interactions with PFAS. This review evaluates current literature, identifies knowledge gaps in current remediation technologies and addresses future strategies on the sequestration of PFAS in contaminated soil using sustainable novel C-based sorbents.

Remediation of PFAS-impacted soils using magnetic activated carbon (MAC) and hydrothermal alkaline treatment (HALT)

Per- and polyfluoroalkyl substances (PFAS) are a group of synthetic pollutants that are bioaccumulative, toxic, and persistent. One long-term source for PFAS release is PFAS-contaminated soil. Addition of activated carbon (AC) to soil has shown the potential to immobilize PFAS and reduce PFAS bioavailability, but PFAS-loaded spent AC remaining in the treated soil could lead to remobilization. Here we report a novel approach to address this challenge. By applying magnetic activated carbon (MAC) to remediate PFAS-impacted soil, the PFAS-loaded MAC can be retrieved from the treated soil and sorbed PFAS in the spent MAC can be destroyed using hydrothermal alkaline treatment (HALT). Effective MAC recovery was observed when water/soil ratios (w/w) were either <0.07 or > 1. Soil organic content and pH affected PFAS adsorption by the MAC added to soil. After three months of incubation with MAC, high PFAS removals [PFOS (87.6 %), PFOA (83.8 %), and 6:2 FTSA (81.5 %)] were observed for acidic environmental sandy soils with low organic content. In contrast, PFAS removal by MAC was poor for garden soils with high organic matter content. MAC was also used to remediate aqueous film-forming foam (AFFF)-impacted and PFAS-contaminated aged soils with varying PFAS removal performance. HALT technology was able to destroy and defluorinate PFAS adsorbed to the spent MAC. Additionally, the HALT-treated MAC retained its magnetic properties and PFOS sorption capacity, suggesting the potential reusability of HALT-treated MAC. Considering the low energy footprint of HALT compared to conventional PFAS thermal destruction techniques, the combination of MAC and HALT could be a promising treatment train for PFAS-contaminated soils.

A critical review of perfluoroalkyl and polyfluoroalkyl substances (PFAS) landfill disposal in the United States

Landfills manage materials containing per- and polyfluoroalkyl substances (PFAS) from municipal solid waste (MSW) and other waste streams. This manuscript summarizes state and federal initiatives and critically reviews peer-reviewed literature to define best practices for managing these wastes and identify data gaps to guide future research. The objective is to inform stakeholders about waste-derived PFAS disposed of in landfills, PFAS emissions, and the potential for related environmental impacts. Furthermore, this document highlights data gaps and uncertainties concerning the fate of PFAS during landfill disposal. Most studies on this topic measured PFAS in liquid landfill effluent (leachate); comparatively fewer have attempted to estimate PFAS loading in landfills or other effluent streams such as landfill gas (LFG). In all media, the reported total PFAS heavily depends on waste types and the number of PFAS included in the analytical method. Early studies which only measured a small number of PFAS, predominantly perfluoroalkyl acids (PFAAs), likely report a significant underestimation of total PFAS. Major findings include relationships between PFAS effluent and landfill conditions - biodegradable waste increases PFAS transformation and leaching. Based on the results of multiple studies, it is estimated that 84% of PFAS loading to MSW landfills (7.2 T total) remains in the waste mass, while 5% leaves via LFG and 11% via leachate on an annual basis. The environmental impact of landfill-derived PFAS has been well-documented. Additional research is needed on PFAS in landfilled construction and demolition debris, hazardous, and industrial waste in the US.

Iron slag permeable reactive barrier for PFOA removal by the electrokinetic process

The efficacy of the Standalone Electrokinetic (EK) process in soil PFAS removal is negligible, primarily due to the intersecting mechanisms of electromigration and electroosmosis transportation. Consequently, the redistribution of PFAS across the soil matrix occurs, hampering effective remediation efforts. Permeable reactive barrier (PRB) has been used to capture contaminants and extract them at the end of the EK process. This study conducted laboratory-scale tests to evaluate the feasibility of the iron slag PRB enhanced-EK process in conjunction with Sodium Cholate (NaC) biosurfactant as a cost-effective and sustainable method for removing PFOA from the soil. A 2 cm iron slag-based PRB with a pH of 9.5, obtained from the steel-making industry, was strategically embedded in the middle of the EK reactors to capture PFOA within the soil. The main component of the slag, iron oxide, exhibited significant adsorption capacity for PFOA contamination. The laboratory-scale tests were conducted over two weeks, revealing a PFOA removal rate of more than 79% in the slag/activated carbon PRB-EK test with NaC enhancement and 70% PFOA removal in the slag/activated carbon PRB-EK without NaC. By extending the duration of the slag/AC PRB-EK test with NaC enhancement to three weeks, the PFOA removal rate increased to 94.09%, with the slag/AC PRB capturing over 87% of the initial PFOA concentration of 10 mg/L. The specific energy required for soil decontamination by the EK process was determined to be 0.15 kWh/kg. The outcomes of this study confirm the feasibility of utilizing iron slag waste in the EK process to capture PFOA contaminants, offering a sustainable approach to soil decontamination. Combining iron slag PRB and NaC biosurfactant provides a cost-effective and environmentally friendly method for efficient PFOA removal from soil.

Immobilization of per- and polyfluoroalkyl substances (PFAS): Comparison of leaching behavior by three different leaching tests

The evaluation of PFAS immobilization performance in laboratory experiments, especially the long-term stability, is a challenge. To contribute to the development of adequate experimental procedures, the impact of experimental conditions on the leaching behavior was studied. Three experiments on different scales were compared: batch, saturated column, and variably saturated laboratory lysimeter experiments. The Infinite Sink (IS) test - a batch test with repeated sampling - was applied for PFAS for the first time. Soil from an agricultural field amended with paper-fiber biosolids polluted with various perfluoroalkyl acids (PFAAs; 655 μg/kg ∑¹⁸PFAAs) and polyfluorinated precursors (1.4 mg/kg ∑¹⁸precursors) was used as the primary material (N-1). Two types of PFAS immobilization agents were tested: treatment with activated carbon-based additives (soil mixtures: R-1 and R-2), and solidification with cement and bentonite (R-3). In all experiments, a chain-length dependent immobilization efficacy is observed. In R-3, the leaching of short-chain PFAAs was enhanced relative to N-1. In column and lysimeter experiments with R-1 and R-2, delayed breakthrough of short-chain PFAAs (C4) occurred (> 90 days; in column experiments at liquid-to-solid ratio (LS) > 30 L/kg) with similar temporal leaching rates suggesting that leaching in these cases was a kinetically controlled process. Observed differences between column and lysimeter experiments may be attributed to varying saturation conditions. In IS experiments, PFAS desorption from N-1, R-1, and R-2 is higher than in the column experiments (N-1: +44 %; R-1: +280 %; R-2: +162 %), desorption of short-chain PFAS occurred predominantly in the initial phase (< 14 days). Our findings demonstrate that sufficient operating times are essential in percolation experiments, e.g., in column experiments >100 days and LS > 30 L/kg. IS experiments may provide a faster estimate for nonpermanent immobilization. The comparison of experimental data from various experiments is beneficial to evaluate PFAS immobilization and to interpret leaching characteristics.

Stabilisation of PFAS in soils: Long-term effectiveness of carbon-based soil amendments

Immobilisation/stabilisation is one of the most developed and studied approaches for treating soils contaminated with per- and poly-fluoroalkyl substances (PFAS). However, its application has been inhibited by insufficient understanding of the effectiveness of added soil sorbents over time. Herein, we present results on the effectiveness of select carbon-based sorbents, over 4 years (longevity) and multiple laboratory leaching conditions (durability). Standard batch leaching tests simulating aggressive, worst-case scenario conditions for leaching (i.e., shaking for 24-48 h at high liquid/solid ratios) were employed to test longevity and durability of stabilisation in clay-loam and sandy-loam soils historically contaminated with PFAS (2 and 14 mg/kg ∑₂₈ PFAS). The different sorbents, which were applied at 1-6% (w/w), reduced leaching of PFAS from the soils to varying degrees. Among the 5 sorbents tested, initial assessments completed 1 week after treatment revealed that 2 powdered activated carbon (PAC) sorbents and 1 biochar were able to reduce leaching of PFAS in the soil by at least 95%. Four years after treatment, the performance of the PAC sorbents did not significantly change, whilst colloidal AC improved and was able to reduce leaching of PFAS by at least 94%. The AC-treated soils also appeared to be durable and achieved at least 95% reduction in PFAS leaching under repetitive leaching events (5 times extraction) and with minimal effect of pH (pH 4-10.5). In contrast, the biochars were affected by aging and were at least 22% less effective in reducing PFAS leaching across a range of leaching conditions. Sorbent performance was generally consistent with the sorbent's physical and chemical characteristics. Overall, the AC sorbents used in this study appeared to be better than the biochars in stabilising PFAS in the long term.

Effect of clay content on the mobilization efficiency of per- and polyfluoroalkyl substances (PFAS) from soils by electrokinetics and hydraulic flushing

The need for the efficient remediation of soils impacted by per- and polyfluoroalkyl substances (PFAS) is substantially growing because of the notable upsurge in societal and regulatory awareness of this class of chemicals. To remediate PFAS-contaminated soils using mobilization approaches, the choice of appropriate techniques highly depends on the soil's composition, particularly the clay content, which significantly affects the soil's permeability. Here, we investigated the PFAS mobilization efficiency from soils with different clay contents by using two techniques: electrokinetic (EK) remediation and hydraulic flushing. Artificial kaolinite was added to a loamy sand soil to prepare four soil blends with clay contents of 5, 25, 50, and 75%, each contaminated with perfluorooctanoic acid (PFOA) and perfulorooctanesulfonic acid (PFOA) at 10,000 μg/kg. EK remediation was conducted by applying a low voltage (30 V) with a current of 100 mA, and hydraulic flushing was carried out by applying a hydraulic gradient (HG) with a slope of 6.7%. Results show that, with a 14-day treatment duration, the EK-mobilization efficiency was enhanced substantially with the increase of clay content (removal of PFOS increased from 20% at 5% clay to 80% at 75% clay), most likely due to the increase of electroosmotic flow due to the higher content of particles having a zeta potential (i.e., clay). For HG, increasing the clay content significantly suppressed the mobilization of PFAS (removal of PFOS decreased from 40% at 5% clay to 10% at 75% clay) due to a notable decrease in the soil's permeability. Based on the results, applying hydraulic flushing and washing techniques for mobilizing PFAS would be appropriate when treating permeable soils with a maximum clay content of about 25%; otherwise, other suitable mobilization techniques such as EKs should be considered.

Recent advances in the remediation of perfluoroalkylated and polyfluoroalkylated contaminated sites

Per- and polyfluoroalkyl substances (PFASs) are compounds used since 1940 in various formulations in the industrial and consumer sectors due to their high chemical and thermal stability. In recent years, PFASs have caused global concern due to their presence in different water and soil matrices, which threatens the environment and human health. These compounds have been reported to be linked to the development of serious human diseases, including but not limited to cancer. For this reason, PFASs have been considered as persistent organic compounds (COPs) and contaminants of emerging concern (CECs). Therefore, this work aims to present the advances in remediation of PFASs-contaminated soil and water by addressing the current literature. The performance and characteristics of each technique were addressed deeply in this work. The reviewed literature found that PFASs elimination studies in soil and water were carried out at a laboratory and pilot-scale in some cases. It was found that ball milling, chemical oxidation and thermal desorption are the most efficient techniques for the removal of PFASs in soils, however, phyto-microbial remediation is under study, which claims to be a promising technique. For the remediation of PFASs-contaminated water, the processes of electrocoagulation, membrane filtration, ozofractionation, catalysis, oxidation reactions - reduction, thermolysis and destructive treatments with plasma have presented the best results. It is noteworthy that hybrid treatments have also proved to be efficient techniques in the removal of these contaminants from soil and water matrices. Therefore, the improvisation and implication of existing techniques on a field-scale are greatly warranted to corroborate the yields obtained on a pilot- and laboratory-scale.

Sampling of freely dissolved per- and polyfluoroalkyl substances (PFAS) in surface water and groundwater using a newly developed passive sampler

Passive sampling methods offer several advantages over traditional grab water sampling techniques, including time-integrative results which better represent long-term concentrations at the site and separation of the freely dissolved fraction of the contaminant which offers insight into the associated risk. This paper describes the performance of a newly developed equilibrium regimen passive sampler designed specifically for per- and polyfluoroalkyl substances (PFAS), called PFAS INSIGHT®. The sampler is effective in sampling ionic (sulfonates and carboxylates) and non-ionic (PFAS precursors) PFAS from aqueous solutions with detection limits similar or lower (depending on the analyte) to those achievable with conventional water sample analysis. Results include laboratory characterization of sorbent adsorption kinetics and adsorption isotherms for 15 PFAS analytes with carbon chain lengths of 4-12, the effects of the sample matrix on PFAS partitioning, and sorbent extraction efficiency. Results from PFAS INSIGHT® field deployments demonstrate good agreement between the concentrations calculated from the passive sampler data and the concentrations measured directly in conventional water samples. Approximately 35% of the passive sampling results were within 2-fold of the conventional water sample concentrations, 71% within 5-fold, and 88% within 10-fold.

Effect of two sorbents on the distribution and transformation of N-ethyl perfluorooctane sulfonamido acetic acid (N-EtFOSAA) in soil-soybean systems

The broad application of perfluoroalkyl acid (PFAA) precursors has led to their occurrence in soil, resulting in potential uptake and bioaccumulation in plants. In this study, we investigated the effect of powdered activated carbon (PAC) and montmorillonite on the distribution and transformation of a perfluorooctanesulfonic acid (PFOS) precursor, N-ethyl perfluorooctane sulfonamido acetic acid (N-EtFOSAA), in soil-plant systems. The results showed that N-EtFOSAA at 300 μg/kg was taken up by soybean roots and shoots together with its transformation products (i.e., perfluorooctane sulfonamide (PFOSA), PFOS), while decreasing the biomass of shoots and roots by 47.63% and 61.16%, respectively. PAC amendment significantly reduced the water leachable and methanol extractable N-EtFOSAA and its transformation products in soil. In the presence of soybean and after 60 days, 73.5% of the initially spiked N-EtFOSAA became non-extractable bound residues. Compared to the spiked controls, the PAC addition also decreased the total plant uptake of N-EtFOSAA by 94.96%. In contrast, montmorillonite showed limited stabilization performance for N-EtFOSAA and its transformation products and was ineffective to lower their bioavailability. Overall, the combination of PAC and soybean was found to be effective in immobilizing N-EtFOSAA in soil.

Application of soil amendments for reducing PFAS leachability and bioavailability

In this study, changes in PFAS leachability and bioavailability were determined following the application of RemBind®100 (R100) and RemBind®300 (R300; 1-10% w/w) to PFAS-contaminated soil (Ʃ₂₈ PFAS 3.093-32.78 mg kg^-1). Small differences were observed in PFAS immobilization efficacy when soil was amended with RemBind® products although adding 5% w/w of either product resulted in a >98% reduction in ASLP PFAS leachability. Variability in immobilization efficacy was attributed to differences in activated carbon composition which influenced physicochemical properties of RemBind® formulations and PFAS sorption. PFOS, PFHxS and PFOA relative bioavailability was also assessed in unamended and amended soil (5% w/w) using an in vivo mouse model. In unamended soil, PFAS relative bioavailability was >60% with differences attributed to physicochemical properties of soil which influenced electrostatic and hydrophobic interactions. However, when PFAS relative bioavailability was assessed in soil amended with 5% w/w R100, individual PFAS relative bioavailability was reduced to 16.1 ± 0.8% to 26.1 ± 0.9% with similar results observed when R300 (5% w/w) was utilised (14.4 ± 1.6% to 24.3 ± 0.8%). Results from this study highlight that soil amendments have the potential to reduce both PFAS leachability and relative bioavailability thereby decreasing mobility and potential exposure to soil-borne contaminants.

Remediation of poly-and perfluoroalkyl substances (PFAS) contaminated soil using gas fractionation enhanced technology

This study investigated a gas fractionation enhanced soil washing method for poly-and perfluoroalkyl substances (PFAS) removal from contaminated soil. With the assistance of gas fractionation, PFAS removal was increased by a factor of 9, compared to the conventional soil washing method. Pre-extraction (pre-treatment) of the soil with water before gas fractionation enhanced PFAS removal from soil. The optimum extraction time varied based on the soil particle size, since it will change the swelling time of the soil. The influence of various operational conditions such as water to soil mass ratio (W:S ratio), gas type in fractionation, gas flowrate, fractionation time and soil pre-treatment condition have been studied to identify the critical influencing factors. Among various W:S ratios (2, 4, 5, 6, 8, and 10) studied, higher W:S ratio resulted in better PFAS removals, but PFAS removal began to plateau as the W:S ratio increased. PFAS removal could be improved by repeated treatment with low water consumption. Air, oxygen, and ozone generated by air and oxygen were used, in which ozone generated by oxygen achieved the highest PFAS removals of 55.9%. Among different fractionation times (10 min, 20 min and 30 min), a fractionation time of 20 min achieved better total PFAS removal for studied soil, because PFOS was the dominant species in the total PFAS. However, the removal of some PFAS species, such as PFHxS, would be increased with extended fractionation time. With constant fractionation time (10 min), PFAS removal performance improved with the increasing gas flowrate.

Per- and polyfluoroalkyl substances in the environment

Over the past several years, the term PFAS (per- and polyfluoroalkyl substances) has grown to be emblematic of environmental contamination, garnering public, scientific, and regulatory concern. PFAS are synthesized by two processes, direct fluorination (e.g., electrochemical fluorination) and oligomerization (e.g., fluorotelomerization). More than a megatonne of PFAS is produced yearly, and thousands of PFAS wind up in end-use products. Atmospheric and aqueous fugitive releases during manufacturing, use, and disposal have resulted in the global distribution of these compounds. Volatile PFAS facilitate long-range transport, commonly followed by complex transformation schemes to recalcitrant terminal PFAS, which do not degrade under environmental conditions and thus migrate through the environment and accumulate in biota through multiple pathways. Efforts to remediate PFAS-contaminated matrices still are in their infancy, with much current research targeting drinking water.

Field-Scale Demonstration of PFAS Leachability Following In Situ Soil Stabilization

A field-scale validation is summarized comparing the efficacy of commercially available stabilization amendments with the objective of mitigating per- and polyfluoroalkyl substance (PFAS) leaching from aqueous film-forming foam (AFFF)-impacted source zones. The scope of this work included bench-scale testing to evaluate multiple amendments and application concentrations to mitigate PFAS leachability and the execution of field-scale soil mixing in an AFFF-impacted fire-training area with nearly 2.5 years of post-soil mixing monitoring to validate reductions in PFAS leachability. At the bench scale, several amendments were evaluated and the selection of two amendments for field-scale evaluation was informed: FLUORO-SORB Adsorbent (FS) and RemBind (RB). Five ∼28 m³ test pits (approximately 3 m wide by 3 m long by 3 m deep) were mixed at a site using conventional construction equipment. One control test pit (Test Pit 1) included Portland cement (PC) only (5% dry weight basis). The other four test pits (Test Pits 2 through 5) compared 5 and 10% ratios (dry weight basis) of FS and RB (also with PC). Five separate monitoring events included two to three sample cores collected from each test pit for United States Environmental Protection Agency (USEPA) Method 1315 leaching assessment. After 1 year, a mass balance for each test pit was attempted comparing the total PFAS soil mass before, during, and after leach testing. Bench-scale and field-scale data were in good agreement and demonstrated >99% decrease in total PFAS leachability (mass basis; >98% mole basis) as confirmed by the total oxidizable precursor assay, strongly supporting the chemical stabilization of PFAS.