Airborne engineered nanomaterials in the workplace-a review of release and worker exposure during nanomaterial production and handling processes

Everything falls apart: How solids degrade and release nanomaterials, composite fragments, and microplastics

To ensure the safe use of materials, one must assess the identity and quantity of exposure. Solid materials, such as plastics, metals, coatings and cements, degrade to some extent during their life cycle, and releases can occur during manufacturing, use and end-of-life. Releases (e.g., what is released, how does release happen, and how much material is released) depend on the composition and internal (nano)structures of the material as well as the applied stresses during the lifecycle. We consider, in some depth, releases from mechanical, weathering and thermal stresses and specifically address the use cases of fused-filament 3D printing, dermal contact, food contact and textile washing. Solid materials can release embedded nanomaterials, composite fragments, or micro- and nanoplastics, as well as volatile organics, ions and dissolved organics. The identity of the release is often a heterogenous mixture and requires adapted strategies for sampling and analysis, with suitable quality control measures. Control materials enhance robustness by enabling comparative testing, but reference materials are not always available as yet. The quantity of releases is typically described by time-dependent rates that are modulated by the nature and intensity of the applied stress, the chemical identity of the polymer or other solid matrix, and the chemical identity and compatibility of embedded engineered nanomaterials (ENMs) or other additives. Standardization of methods and the documentation of metadata, including all the above descriptors of the tested material, applied stresses, sampling and analytics, are identified as important needs to advance the field and to generate robust, comparable assessments. In this regard, there are strong methodological synergies between the study of all solid materials, including the study of micro- and nanoplastics. From an outlook perspective, we review the hazard of the released entities, and show how this informs risk assessment. We also address the transfer of methods to related issues such as tyre wear, advanced materials and advanced manufacturing, biodegradable polymers, and non-solid matrices. As the consideration of released entities will become more routine in industry via lifecycle assessment in Safe-and-Sustainable-by-Design practices, release assessments will require careful design of the study with quality controls, the use of agreed-on test materials and standardized methods where these exist and the adoption of clearly defined data reporting practices that enable data reuse, meta-analyses, and comparative studies.

A comprehensive review on monitoring and purification of water through tunable 2D nanomaterials

Instead of typical household trash, the heavy metal complexes, organic chemicals, and other poisons produced by huge enterprises threaten water systems across the world. In order to protect our drinking water from pollution, we must keep a close eye on the situation. Nanotechnology, specifically two-dimensional (2D) nanomaterials, is used in certain wastewater treatment systems. Graphene, g-C3N4, MoS2, and MXene are just a few examples of emerging 2D nanomaterials that exhibit an extraordinary ratio of surface (m3), providing material consumption, time consumption, and treatment technique for cleaning and observing water. In this post, we'll talk about the ways in which 2D nanomaterials may be tuned to perform certain functions, namely how they can be used for water management. The following is a quick overview of nanostructured materials and its possible use in water management: Also discussed in length are the applications of 2D nanomaterials in water purification, including pollutant adsorption, filtration, disinfection, and photocatalysis. Fluorescence sensors, colorimetric, electrochemical, and field-effect transistors are only some of the devices being studied for their potential use in monitoring water quality using 2D nanomaterials. Utilizing 2D content has its benefits and pitfalls when used to water management. New developments in this fast-expanding business will boost water treatment quality and accessibility in response to rising awareness of the need of clean, fresh water among future generations.

Integrating Exposure Assessment and Process Hazard Analysis: The Nano-Enabled 3D Printing Filament Extrusion Case

Nanoparticles are being used in novel applications of the thermoplastics industry, including automotive parts, the sports industry and leisure and consumer goods, which can be produced nowadays through additive manufacturing. However, there is limited information on the health and safety aspects during the production of these new materials, mainly from recycled sources. This study covers the exposure assessment to nano- and micro-size particles emitted from the nanocomposites during the production of filaments for 3D printing through a compounding and extrusion pilot line using recycled (post-industrial) thermoplastic polyurethane (TPU) and recycled polyamide 12 (PA12), which have been also upcycled through reinforcement with iron oxide nanoparticles (Fe₃O₄ NPs), introducing matrix healing properties triggered by induction heating. The assessment protocol included near- and far-field measurements, considering the extruder as the primary emission source, and portable measuring devices for evaluating particulate emissions reaching the inhalable zone of the lab workers. A Failure Modes and Effects Analysis (FMEA) study for the extrusion process line was defined along with a Failure Tree Analysis (FTA) process in which the process deviations, their sources and the relations between them were documented. FTA allowed the identification of events that should take place in parallel (simultaneously) or in series for the failure modes to take place and the respective corrective actions to be proposed (additional to the existing control measures).

Application of Inorganic Nanomaterials in Cultural Heritage Conservation, Risk of Toxicity, and Preventive Measures

Nanotechnology has allowed for significant progress in architectural, artistic, archaeological, or museum heritage conservation for repairing and preventing damages produced by deterioration agents (weathering, contaminants, or biological actions). This review analyzes the current treatments using nanomaterials, including consolidants, biocides, hydrophobic protectives, mechanical resistance improvers, flame-retardants, and multifunctional nanocomposites. Unfortunately, nanomaterials can affect human and animal health, altering the environment. Right now, it is a priority to stop to analyze its advantages and disadvantages. Therefore, the aims are to raise awareness about the nanotoxicity risks during handling and the subsequent environmental exposure to all those directly or indirectly involved in conservation processes. It reports the human-body interaction mechanisms and provides guidelines for preventing or controlling its toxicity, mentioning the current toxicity research of main compounds and emphasizing the need to provide more information about morphological, structural, and specific features that ultimately contribute to understanding their toxicity. It provides information about the current documents of international organizations (European Commission, NIOSH, OECD, Countries Normative) about worker protection, isolation, laboratory ventilation control, and debris management. Furthermore, it reports the qualitative risk assessment methods, management strategies, dose control, and focus/receptor relationship, besides the latest trends of using nanomaterials in masks and gas emissions control devices, discussing their risk of toxicity.

Critical aspects in occupational exposure assessment with different aerosol metrics in an industrial spray coating process

Engineered Nanomaterials (ENMs) have several uses in various industrial fields and are embedded in a myriad of consumer products. However, there is continued concern over the potential adverse health effects and environmental impacts of ENMs due to their unique physico-chemical characteristics. Currently, there are no specific international regulations for various ENMs. There are also no Occupational Exposure Limits (OEL) regulated by the European Union (EU) for nanomaterials in the form of nano-objects, their aggregates or agglomerates (NOAA). For ENMs the question of which metric to be used (i.e., mass, surface area, number concentrations) to determine the exposure is still not resolved. The aim of this work is to assess the worker exposure by inhalation in an industrial spray coating process by using all three metrics mentioned above. Two target ENMs (N-doped TiO₂, TiO₂N and AgNPs capped with a quaternized hydroxyethyl-cellulose, AgHEC) generated for industrial-scale spraying processes were considered. Results showed that the averaged particle number concentration (10-100 nm) was below 2.7 10⁴ cm^-3 for both materials. The Lung Deposited Surface Area (LDSA) was in the range between 73 and 98 μm²cm^-3 and the particle mass concentration (obtained by means of ICP-EOS off-line analysis) resulted below 70 μg m^-3 and 0.4 μg m^-3 for TiO₂ and Ag, respectively. Although, the airborne particles concentration compared well with the NIOSH Recommended Exposure Level (REL) limits the contribution to the background, according to EN 17058 (Annex E) was significant (particularly in the particle number and PM1 mass concentrations). We successfully evaluated the worker exposure by means of the different airborne particles' metrics (number, surface and mass concentrations). We concluded that worker exposure assessment involving ENMs is a complex procedure with requires both real time and off-line measurements and a deep investigation of the background.

Prospects of Polymeric Nanocomposite Membranes for Water Purification and Scalability and their Health and Environmental Impacts: A Review

Water shortage is a major worldwide issue. Filtration using genuine polymeric membranes demonstrates excellent pollutant separation capabilities; however, polymeric membranes have restricted uses. Nanocomposite membranes, which are produced by integrating nanofillers into polymeric membrane matrices, may increase filtration. Carbon-based nanoparticles and metal/metal oxide nanoparticles have received the greatest attention. We evaluate the antifouling and permeability performance of nanocomposite membranes and their physical and chemical characteristics and compare nanocomposite membranes to bare membranes. Because of the antibacterial characteristics of nanoparticles and the decreased roughness of the membrane, nanocomposite membranes often have greater antifouling properties. They also have better permeability because of the increased porosity and narrower pore size distribution caused by nanofillers. The concentration of nanofillers affects membrane performance, and the appropriate concentration is determined by both the nanoparticles' characteristics and the membrane's composition. Higher nanofiller concentrations than the recommended value result in deficient performance owing to nanoparticle aggregation. Despite substantial studies into nanocomposite membrane manufacturing, most past efforts have been restricted to the laboratory scale, and the long-term membrane durability after nanofiller leakage has not been thoroughly examined.

Measuring TiO2N and AgHEC Airborne Particle Density during a Spray Coating Process

Effective particle density is a key parameter for assessing inhalation exposure of engineered NPs in occupational environments. In this paper, particle density measurements were carried out using two different techniques: one based on the ratio between mass and volumetric particle concentrations; the other one based on the ratio between aerodynamic and geometric particle diameter. These different approaches were applied to both field- and laboratory-scale atomization processes where the two target NPs (N-doped TiO₂, TiO₂N and AgNPs capped with a quaternized hydroxyethylcellulose, AgHEC) were generated. Spray tests using TiO₂N were observed to release more and bigger particles than tests with AgHEC, as indicated by the measured particle mass concentrations and volumes. Our findings give an effective density of TiO₂N particle to be in a similar range between field and laboratory measurements (1.8 ± 0.5 g/cm³); while AgHEC particle density showed wide variations (3.0 ± 0.5 g/cm³ and 1.2 + 0.1 g/cm³ for field and laboratory campaigns, respectively). This finding leads to speculation regarding the composition of particles emitted because atomized particle fragments may contain different Ag-to-HEC ratios, leading to different density values. A further uncertainty factor is probably related to low process emissions, making the subtraction of background concentrations from AgHEC process emissions unreliable.

Pulmonary Toxicity of Silica Linked to Its Micro- or Nanometric Particle Size and Crystal Structure: A Review

Silicon dioxide (SiO2) is a mineral compound present in the Earth’s crust in two mineral forms: crystalline and amorphous. Based on epidemiological and/or biological evidence, the pulmonary effects of crystalline silica are considered well understood, with the development of silicosis, emphysema, chronic bronchitis, or chronic obstructive pulmonary disease. The structure and capacity to trigger oxidative stress are recognized as relevant determinants in crystalline silica’s toxicity. In contrast, natural amorphous silica was long considered nontoxic, and was often used as a negative control in experimental studies. However, as manufactured amorphous silica nanoparticles (or nanosilica or SiNP) are becoming widely used in industrial applications, these paradigms must now be reconsidered at the nanoscale (<100 nm). Indeed, recent experimental studies appear to point towards significant toxicity of manufactured amorphous silica nanoparticles similar to that of micrometric crystalline silica. In this article, we present an extensive review of the nontumoral pulmonary effects of silica based on in vitro and in vivo experimental studies. The findings of this review are presented both for micro- and nanoscale particles, but also based on the crystalline structure of the silica particles.

A New Look at the Effects of Engineered ZnO and TiO2 Nanoparticles: Evidence from Transcriptomics Studies

Titanium dioxide (TiO2) and zinc oxide (ZnO) nanoparticles (NPs) have attracted a great deal of attention due to their excellent electrical, optical, whitening, UV-adsorbing and bactericidal properties. The extensive production and utilization of these NPs increases their chances of being released into the environment and conferring unintended biological effects upon exposure. With the increasingly prevalent use of the omics technique, new data are burgeoning which provide a global view on the overall changes induced by exposures to NPs. In this review, we provide an account of the biological effects of ZnO and TiO2 NPs arising from transcriptomics in in vivo and in vitro studies. In addition to studies on humans and mice, we also describe findings on ecotoxicology-related species, such as Danio rerio (zebrafish), Caenorhabditis elegans (nematode) or Arabidopsis thaliana (thale cress). Based on evidence from transcriptomics studies, we discuss particle-induced biological effects, including cytotoxicity, developmental alterations and immune responses, that are dependent on both material-intrinsic and acquired/transformed properties. This review seeks to provide a holistic insight into the global changes induced by ZnO and TiO2 NPs pertinent to human and ecotoxicology.

Towards health-based nano reference values (HNRVs) for occupational exposure: Recommendations from an expert panel

Unique physicochemical characteristics of engineered nanomaterials (ENMs) suggest the need for nanomaterial-specific occupational exposure limits (OELs). Setting these limits remains a challenge. Therefore, the aim of this study was to set out a framework to evaluate the feasibility of deriving advisory health-based occupational limit values for groups of ENMs, based on scientific knowledge. We have used an expert panel approach to address three questions: 1) What ENM-categories should be distinguished to derive advisory health-based occupational limit values (or health-based Nano Reference Values, HNRVs) for groups of ENMs? 2) What evidence would be needed to define values for these categories? And 3) How much effort would it take to achieve this? The panel experts distinguished six possible categories of HNRVs: A) WHO-fiber-like high aspect ratio ENMs (HARNs), B) Non-WHO-fiber-like HARNs and other non-spheroidal ENMs, C) readily soluble spheroidal ENMs, D) biopersistent spheroidal ENMs with unknown toxicity, E) biopersistent spheroidal ENMs with substance-specific toxicity and F) biopersistent spheroidal ENMs with relatively low substance-specific toxicity. For category A, the WHO-fiber-like HARNs, agreement was reached on criteria defining this category and the approach of using health-based risk estimates for asbestos to derive the HNRV. For category B, a quite heterogeneous category, more toxicity data are needed to set an HNRV. For category C, readily soluble spheroidal ENMs, using the OEL of their molecular or ionic counterpart would be a good starting point. For the biopersistent ENMs with unknown toxicity, HNRVs cannot be applied as case-by-case testing is required. For the other biopersistent ENMs in category E and F, we make several recommendations that can facilitate the derivation of these HNRVs. The proposed categories and recommendations as outlined by this expert panel can serve as a reference point for derivation of HNRVs when health-based OELs for ENMs are not yet available.

Nanowaste: Another Future Waste, Its Sources, Release Mechanism, and Removal Strategies in the Environment

Nanowaste is defined as waste derived from materials with at least one dimension in the 1–100 nm range. The nanomaterials containing products are considered as “nanoproducts” and they can lead to the development of nanomaterial-containing waste, also termed as “nanowaste”. The increased production and consumption of these engineered nanomaterials (ENMs) and nanoproducts that generate enormous amounts of nanowaste have raised serious concerns about their fate, behavior, and ultimate disposal in the environment. It is of the utmost importance that nanowaste is disposed of in an appropriate manner to avoid an adverse impact on human health and the environment. The unique properties of ENMs, combined with an inadequate understanding of appropriate treatment techniques for many forms of nanowaste, makes nanowaste disposal a complex task. Presently, there is a lack of available information on the optimized standards for identifying, monitoring, and managing nanowaste. Therefore, this review highlights concerns about nanowaste as future waste that need to be addressed. The review focuses on ENMs waste (in the form of NP, nanotubes, nanowires, and quantum dots) generated from the manufacture of a wide variety of nanoproducts that end up as nanowaste and adversely affect the environment. Furthermore, the review considers different types of ENMs in waste streams and environmental compartments (i.e., soil, water, and air). Detailed studies are still required to identify data gaps and implement strategies to remove and control this future waste.

Validation and Demonstration of an Atmosphere-Temperature-pH-Controlled Stirred Batch Reactor System for Determination of (Nano)Material Solubility and Dissolution Kinetics in Physiological Simulant Lung Fluids

In this study, we present a dissolution test system that allows for the testing of dissolution of nano- and micrometer size materials under highly controlled atmospheric composition (O2 and CO2), temperature, and pH. The system enables dissolution testing in physiological simulant fluids (here low-calcium Gamble’s solution and phagolysosomal simulant fluid) and derivation of the temporal dissolution rates and reactivity of test materials. The system was validated considering the initial dissolution rates and dissolution profiles using eight different materials (γ-Al2O3, TiO2 (NM-104 coated with Al2O3 and glycerin), ZnO (NM-110 and NM-113, uncoated; and NM-111 coated with triethoxycaprylsilane), SiO2 (NM-200—synthetic amorphous silica), CeO2 (NM-212), and bentonite (NM-600) showing high intra-laboratory repeatability and robustness across repeated testing (I, II, and III) in triplicate (replicate 1, 2, and 3) in low-calcium Gamble’s solution. A two-way repeated-measures ANOVA was used to determine the intra-laboratory repeatability in low-calcium Gamble’s solution, where Al2O3 (p = 0.5277), ZnO (NM-110, p = 0.6578), ZnO (NM-111, p = 0.0627), and ZnO (NM-113, p = 0.4210) showed statistical identical repeatability across repeated testing (I, II, and III). The dissolution of the materials was also tested in phagolysosomal simulant fluid to demonstrate the applicability of the ATempH SBR system in other physiological fluids. We further show the uncertainty levels at which dissolution can be determined using the ATempH SBR system.

Particles Emission from an Industrial Spray Coating Process Using Nano-Materials

Industrial spray coating processes are known to produce excellent coatings on large surfaces and are thus often used for in-line production. However, they could be one of the most critical sources of worker exposure to ultrafine particles (UFPs). A monitoring campaign at the Witek s.r.l. (Florence, Italy) was deployed to characterize the release of TiO₂ NPs doped with nitrogen (TiO₂-N) and Ag capped with hydroxyethyl cellulose (AgHEC) during automatic industrial spray-coating of polymethyl methacrylate (PMMA) and polyester. Aerosol particles were characterized inside the spray chamber at near field (NF) and far field (FF) locations using on-line and off-line instruments. Results showed that TiO₂-N suspension produced higher particle number concentrations than AgHEC in the size range 0.3–1 µm (on average 1.9 10² p/cm³ and 2.5 10¹ p/cm³, respectively) after background removing. At FF, especially at worst case scenario (4 nozzles, 800 mL/min flow rate) for TiO₂-N, the spray spikes were correlated with NF, with an observed time lag of 1 minute corresponding to a diffusion speed of 0.1 m/s. The averaged ratio between particles mass concentrations in the NF position and inside the spray chamber was 1.7% and 1.5% for TiO₂-N and for AgHEC suspensions, respectively. The released particles’ number concentration of TiO₂-N in the size particles range 0.3–1 µm was comparable for both PMMA and polyester substrates, about 1.5 and 1.6 10² p/cm³. In the size range 0.01–30 µm, the aerosol number concentration at NF for both suspensions was lower than the nano reference values (NRVs) of 16·10³ p/cm^-3.

Occupational risk of nano-biomaterials: Assessment of nano-enabled magnetite contrast agent using the BIORIMA Decision Support System

The assessment of the safety of nano-biomedical products for patients is an essential prerequisite for their market authorization. However, it is also required to ensure the safety of the workers who may be unintentionally exposed to the nano-biomaterials (NBMs) in these medical applications during their synthesis, formulation into products and end-of-life processing and also of the medical professionals (e.g., nurses, doctors, dentists) using the products for treating patients. There is only a handful of workplace risk assessments focussing on NBMs used in medical applications. Our goal is to contribute to increasing the knowledge in this area by assessing the occupational risks of magnetite (Fe₃O₄) nanoparticles coated with PLGA-b-PEG-COOH used as contrast agent in magnetic resonance imaging (MRI) by applying the software-based Decision Support System (DSS) which was developed in the EU H2020 project BIORIMA. The occupational risk assessment was performed according to regulatory requirements and using state-of-the-art models for hazard and exposure assessment, which are part of the DSS. Exposure scenarios for each life cycle stage were developed using data from literature, inputs from partnering industries and results of a questionnaire distributed to healthcare professionals, i.e., physicians, nurses, technicians working with contrast agents for MRI. Exposure concentrations were obtained either from predictive exposure models or monitoring campaigns designed specifically for this study. Derived No-Effect Levels (DNELs) were calculated by means of the APROBA tool starting from in vivo hazard data from literature. The exposure estimates/measurements and the DNELs were used to perform probabilistic risk characterisation for the formulated exposure scenarios, including uncertainty analysis. The obtained results revealed negligible risks for workers along the life cycle of magnetite NBMs used as contrast agent for the diagnosis of tumour cells in all exposure scenarios except in one when risk is considered acceptable after the adoption of specific risk management measures. The study also demonstrated the added value of using the BIORIMA DSS for quantification and communication of occupational risks of nano-biomedical applications and the associated uncertainties.

Evaluation of 1-dimensional nanomaterials release during electrospinning and thermogravimetric analysis

The growing research interests with engineered nanomaterials in academic laboratories and manufacturing facilities pose potential safety risks to students and workers. New nanoparticle substances, compositions, and processing approaches are developed regularly, creating new health risks which may not have been addressed previously. Accordingly, the Institute of Occupational Medicine conducted field studies at Texas A&M University (TAMU) to characterize possible particle emissions during processing and fabrication of carbon nanotubes, copper nanowires, and polymeric fibers. The nature of the monitoring work carried out at TAMU was to investigate the potential release of 1D nanomaterials to air from activities associated with synthesis, handling, thermal gravimetric analysis, and electrospinning processes, and evaluate the effectiveness of the utilized control measures. The potential nanoparticle release to air from each activity was investigated using a combination of particle detection instrumentations, coupled with standard filter-based sampling techniques. The analyses indicated that a measurable quantity of free carbon nanosphere aggregates was detected during these activities; however, no free MWCNTs or nanowires were detected. Scanning electron microscopy identified the presence of carbon nanospheres aggregates on the filters. While the control measures used at TAMU are effective in containing the nanomaterial release during processing, poor handling and occupational hygiene practices can increase the risk of employee exposure to the nanomaterials.

NanoSafe III: A User Friendly Safety Management System for Nanomaterials in Laboratories and Small Facilities

Research in nanoscience continues to bring forward a steady stream of new nanomaterials and processes that are being developed and marketed. While scientific committees and expert groups deal with the harmonization of terminology and legal challenges, risk assessors in research labs continue to have to deal with the gap between regulations and rapidly developing information. The risk assessment of nanomaterial processes is currently slow and tedious because it is performed on a material-by-material basis. Safety data sheets are rarely available for (new) nanomaterials, and even when they are, they often lack nano-specific information. Exposure estimations or measurements are difficult to perform and require sophisticated and expensive equipment and personal expertise. The use of banding-based risk assessment tools for laboratory environments is an efficient way to evaluate the occupational risks associated with nanomaterials. Herein, we present an updated version of our risk assessment tool for working with nanomaterials based on a three-step control banding approach and the precautionary principle. The first step is to determine the hazard band of the nanomaterial. A decision tree allows the assignment of the material to one of three bands based on known or expected effects on human health. In the second step, the work exposure is evaluated and the processes are classified into three "nano" levels for each specific hazard band. The work exposure is estimated using a laboratory exposure model. The result of this calculation in combination with recommended occupational exposure limits (rOEL) for nanomaterials and an additional safety factor gives the final "nano" level. Finally, we update the technical, organizational, and personal protective measures to allow nanomaterial processes to be established in research environments.

Contact transfer of engineered nanomaterials in the workplace

This study investigates the potential spread of cadmium selenide quantum dots in laboratory environments through contact of gloves with simulated dry spills on laboratory countertops. Secondary transfer of quantum dots from the contaminated gloves to other substrates was initiated by contact of the gloves with different materials found in the laboratory. Transfer of quantum dots to these substrates was qualitatively evaluated by inspection under ultraviolet illumination. This secondary contact resulted in the delivery of quantum dots to all the evaluated substrates. The amount of quantum dots transferred was quantified by elemental analysis. The residue containing quantum dots picked up by the glove was transferred to at least seven additional sections of the pristine substrate through a series of sequential contacts. These results demonstrate the potential for contact transfer as a pathway for spreading nanomaterials throughout the workplace, and that 7-day-old dried spills are susceptible to the propagation of nanomaterials by contact transfer. As research and commercialization of engineered nanomaterials increase worldwide, it is necessary to establish safe practices to protect workers from the potential for chronic exposure to potentially hazardous materials. Similar experimental procedures to those described herein can be adopted by industries or regulatory agencies to guide the development of their nanomaterial safety programmes.

Inflammatory response in human alveolar epithelial cells after TiO2 NPs or ZnO NPs exposure: Inhibition of surfactant protein A expression as an indicator for loss of lung function

The increasing use of metal oxide nanoparticles (MONPs) as TiO₂ NPs or ZnO NPs has led to environmental release and human exposure. The respiratory system, effects on lamellar bodies and surfactant protein A (SP-A) of pneumocytes, can be importantly affected. Exposure of human alveolar epithelial cells (A549) induced differential responses; a higher persistence of TiO₂ in cell surface and uptake (measured by Atomic Force Microscopy) and sustained inflammatory response (by means of TNF-α, IL-10, and IL-6 release) and ROS generation were observed, whereas ZnO showed a modest response and low numbers in cell surface. A reduction in SP-A levels at 24 h of exposure to TiO₂ NPs (concentration-dependent) or ZnO NPs (the higher concentration) was also observed, reversed by blocking the inflammatory response (by the inhibition of IL-6). Loss of SP-A represents a relevant target of MONPs-induced inflammatory response that could contribute to cellular damage and loss of lung function.

Occupational Exposures to Engineered Nanomaterials: a Review of Workplace Exposure Assessment Methods

PURPOSE OF REVIEW

The purpose of this review is to consolidate exposure assessment methods for occupational research on engineered nanomaterials (ENMs) published within the past 5 years (2015-2020).

RECENT FINDINGS

The three ENMs that generated the highest volume of new research include titanium dioxide, graphene, and aluminum oxide. A multi-metric approach, using both online and offline instruments and analyses, has been found to be a useful method to characterize ENM workplace exposures and was commonly used in the recently published literature. Particle number concentration was the most common online exposure metric used, followed by the metrics of mass and surface area. There are currently no consensus methods for offline analyses of most ENMs. Researchers generally used gravimetric or elemental analyses for carbonaceous nanomaterials, titanium dioxide, and other nanometals, but there was little overlap between other ENM materials reviewed. Using biological markers of exposure, such as urinary oxidative stress biomarkers, as an indication of chronic exposure may also be useful for some ENMs and should be further researched. Generally, similar online instrumentation and offline electron microscopy methods were used for all ENMs. However, this consistency was not observed for offline mass analysis methods within specific ENMs. Consolidation of the most recent methods and results of exposure assessments within this broad material category can guide researchers toward future areas of study. Establishing consensus methods of exposure assessment for each individual ENM is crucial to characterizing workplace exposures, pooling data to fully understand their associated risks, and developing useful occupational exposure limits.

Estimates of lung burden risk associated with long-term exposure to TiO2 nanoparticles as a UV-filter in sprays

Titanium dioxide (TiO2) nanoparticles (NPs) are employed as an ultraviolet filter in sunscreen products because of their high ultraviolet absorptivity. However, sunscreen sprays may pose health risks due to the toxicity of inhaled TiO2 NPs. Therefore, we estimated the potential human health risk posed by inhaled TiO2 NPs emitted from sunscreen sprays. The physiology-based lung model was employed to predict the lung TiO2 NPs burden caused by long-term exposure. A Hill-based dose-response model described the relationship between lung inflammation and TiO2 NP accumulation. The Weibull threshold model was used to estimate the threshold amount of accumulation inducing 0.5% of the maximum increase in neutrophils. The potential health risk was assessed using a hazard quotient-based probabilistic risk model. All data obtained to date indicate that application of sunscreen sprays poses no significant health risk. However, using data simulations based on the threshold criterion, we discovered that in terms of practical strategies for preventing the risks posed by inhaled TiO2 NPs emitted from spray products, the suggested daily use amount and pressing number are 40 g (95% confidence interval: 11-146 g) and 66 (18-245), respectively. In this study, we successfully translated the potential health risk of long-term exposure to NP-containing sunscreen sprays and recommendations for daily application into mechanistic insights.

Recent Developments in the Application of Nanomaterials in Agroecosystems

Nanotechnology implies the scientific research, development, and manufacture, along with processing, of materials and structures on a nano scale. Presently, the contamination of metalloids and metals in the soil has gained substantial attention. The consolidation of nanomaterials and plants in ecological management has received considerable research attention because certain nanomaterials could enhance plant seed germination and entire plant growth. Conversely, when the nanomaterial concentration is not properly controlled, toxicity will definitely develop. This paper discusses the role of nanomaterials as: (1) nano-pesticides (for improving the plant resistance against the biotic stress); and (2) nano-fertilizers (for promoting the plant growth by providing vital nutrients). This review analyzes the potential usages of nanomaterials in agroecosystem. In addition, the adverse effects of nanomaterials on soil organisms are discussed. We mostly examine the beneficial effects of nanomaterials such as nano-zerovalent iron, iron oxide, titanium dioxide, nano-hydroxyapatite, carbon nanotubes, and silver- and copper-based nanomaterials. Some nanomaterials can affect the growth, survival, and reproduction of soil organisms. A change from testing/using nanomaterials in plants for developing nanomaterials depending on agricultural requirements would be an important phase in the utilization of nanomaterials in sustainable agriculture. Conversely, the transport as well as ecological toxicity of nanomaterials should be seriously examined for guaranteeing its benign usage in agriculture.

From nano to micrometer size particles - A characterization of airborne cement particles during construction activities

Although, photocatalytic cement contains nanosized TiO₂, a possibly carcinogen, no exposure assessments exist for construction workers. We characterized airborne nanoparticle exposures during construction activities simulated in an exposure chamber. We collected some construction site samples for regular cement in Switzerland and Thailand for comparison. Airborne nanoparticles were characterized using scanning mobility particle sizer (SMPS), portable aerosol spectrometer (PAS), diffusion size classifier (DiSCmini), transmission electron microscopy (TEM), scanning electron microscope energy dispersive X-ray spectroscopy (SEM-EDX), and X-ray diffraction. Bagged photocatalytic cement had 2.0 wt% (GSD ± 0.55) TiO₂, while TiO₂ in aerosols reached 16.5 wt% (GSD ± 1.72) during bag emptying and 9.7 wt% (GSD ± 1.36) after sweeping. The airborne photocatalytic cement particles were far smaller (approximately 50 nm) compared to regular cement. Cutting blocks made from photocatalytic cement or concrete, resulted in similar amounts of airborne nano TiO₂ (2.0 wt% GSD ± 0.57) particles as in bagged material. Both photocatalytic and regular cement had a geometric mean diameter (GMD) < 3.5 μm. Main exposures for Thai workers were during sweeping and Swiss workers during drilling and polishing cement blocks. Targeted nanoparticle exposure assessments are needed as a significantly greater exposure to nano TiO₂ were observed than what would have been predicted from the material's nano- TiO₂ contents.

Exposure, assessment and health hazards of particulate matter in metal additive manufacturing: A review

Metal additive manufacturing (AM), also known as metal three-dimensional (3D) printing, is a new technology offering design freedom to create complex structures that has found increasing applications in industrial processes. However, due to the fine metal powders and high temperatures involved, the printing process is likely to generate particulate matter (PM) that has a detrimental impact on the environment and human health. Therefore, comprehensive assessement of the exposure and health hazards of PM pollution related to this technique is urgently required. This review provides general knowledge of metal AM and its possible particle release. The health issues of metal PM are described considering the exposure routes, adverse human health outcomes and influencing factors. Methods of evaluating PM exposure and risk assessment techniques are also summarized. Lastly, future research needs are suggested. The information and knowledge presented in this review will contribute to the understanding, assessment, and control of possible risks in metal AM and benefit the wider metal 3D printing community, which includes machine operators, consumers, R&D scientists, and policymakers.

Identification of nanomaterials by the volume specific surface area (VSSA) criterion: application to powder mixes

We demonstrate the relevance of the Volume Specific Surface Area (VSSA) parameter to identify the nanoparticulate character of powder mixes based on either spherical constituent particles with bimodal size distributions (TiO₂), or fiber-like constituent particles with unimodal size distributions (sepiolite and sepiolite-based pigments). These new results indicate that VSSA could reasonably be proposed as an optional criterion in the future for the definition of nanomaterials based on the European Commission recommendation, provided certain requirements are fulfilled.

Quartz crystal microbalances (QCM) are suitable for real-time dosimetry in nanotoxicological studies using VITROCELL®Cloud cell exposure systems

Background

Accurate knowledge of cell−/tissue-delivered dose plays a pivotal role in inhalation toxicology studies, since it is the key parameter for hazard assessment and translation of in vitro to in vivo dose-response. Traditionally, (nano-)particle toxicological studies with in vivo and in vitro models of the lung rely on in silio computational or off-line analytical methods for dosimetry. In contrast to traditional in vitro testing under submerged cell culture conditions, the more physiologic air-liquid interface (ALI) conditions offer the possibility for real-time dosimetry using quartz crystal microbalances (QCMs). However, it is unclear, if QCMs are sensitive enough for nanotoxicological studies. We investigated this issue for two commercially available VITROCELL®Cloud ALI exposure systems.

Results

Quantitative fluorescence spectroscopy of fluorescein-spiked saline aerosol was used to determine detection limit, precision and accuracy of the QCMs implemented in a VITROCELL®Cloud 6 and Cloud 12 system for dose-controlled ALI aerosol-cell exposure experiments. Both QCMs performed linearly over the entire investigated dose range (200 to 12,000 ng/cm²) with an accuracy of 3.4% (Cloud 6) and 3.8% (Cloud 12). Their precision (repeatability) decreased from 2.5% for large doses (> 9500 ng/cm²) to values of 10% and even 25% for doses of 1000 ng/cm² and 200 ng/cm², respectively. Their lower detection limit was 170 ng/cm² and 169 ng/cm² for the Cloud 6 and Cloud 12, respectively. Dose-response measurements with (NM110) ZnO nanoparticles revealed an onset dose of 3.3 μg/cm² (or 0.39 cm²/cm²) for both cell viability (WST-1) and cytotoxicity (LDH) of A549 lung epithelial cells.

Conclusions

The QCMs of the Cloud 6 and Cloud 12 systems show similar performance and are highly sensitive, accurate devices for (quasi-) real-time dosimetry of the cell-delivered particle dose in ALI cell exposure experiments, if operated according to manufacturer specifications. Comparison with in vitro onset doses from this and previously published ALI studies revealed that the detection limit of 170 ng/cm² is sufficient for determination of toxicological onset doses for all particle types with low (e.g. polystyrene) or high mass-specific toxicity (e.g. ZnO and Ag) investigated here. Hence, in principle QCMs are suitable for in vitro nanotoxciological studies, but this should be investigated for each QCM and ALI exposure system under the specific exposure conditions as described in the present study.

Developments in the Application of Nanomaterials for Water Treatment and Their Impact on the Environment

Nanotechnology is an uppermost priority area of research in several nations presently because of its enormous capability and financial impact. One of the most promising environmental utilizations of nanotechnology has been in water treatment and remediation where various nanomaterials can purify water by means of several mechanisms inclusive of the adsorption of dyes, heavy metals, and other pollutants, inactivation and removal of pathogens, and conversion of harmful materials into less harmful compounds. To achieve this, nanomaterials have been generated in several shapes, integrated to form different composites and functionalized with active components. Additionally, the nanomaterials have been added to membranes that can assist to improve the water treatment efficiency. In this paper, we have discussed the advantages of nanomaterials in applications such as adsorbents (removal of dyes, heavy metals, pharmaceuticals, and organic contaminants from water), membrane materials, catalytic utilization, and microbial decontamination. We discuss the different carbon-based nanomaterials (carbon nanotubes, graphene, graphene oxide, fullerenes, etc.), and metal and metal-oxide based nanomaterials (zinc-oxide, titanium dioxide, nano zerovalent iron, etc.) for the water treatment application. It can be noted that the nanomaterials have the ability for improving the environmental remediation system. The examination of different studies confirmed that out of the various nanomaterials, graphene and its derivatives (e.g., reduced graphene oxide, graphene oxide, graphene-based metals, and graphene-based metal oxides) with huge surface area and increased purity, outstanding environmental compatibility and selectivity, display high absorption capability as they trap electrons, avoiding their recombination. Additionally, we discussed the negative impacts of nanomaterials such as membrane damage and cell damage to the living beings in the aqueous environment. Acknowledgment of the possible benefits and inadvertent hazards of nanomaterials to the environment is important for pursuing their future advancement.

Impact of Source Position and Obstructions on Fume Hood Releases

A fume hood is the most central piece of safety equipment available to researchers in a laboratory environment. While it is understood that the face velocity and sash height can drastically influence airflow patterns, few specific recommendations can be given to the researcher to guide them to maximize the safety of their particular hood. This stems from the issue that fundamentally little is known regarding how obstructions within the hood can push potentially harmful particles or chemicals out of the fume hood and into the breathing zone. In this work, we demonstrate how the position of a typical nanoparticle synthesis setup, including a Schlenk line and stir plate on an adjustable stand, influences airflow in a constant velocity fume hood. Using a combination of smoke evolution experiments and the aid of computational fluid dynamics simulations, we show how the location and height of the reaction components impact airflow. This work offers a highly visual display intended especially for new or inexperienced fume hood users. Based upon our studies and simulations, we provide detailed guidance to researchers and lab technicians on how to optimally modify reaction placement in order to protect the breathing zone while working.

Characteristics of iron status, oxidation response, and DNA methylation profile in response to occupational iron oxide nanoparticles exposure

Although the growing development and application of iron oxide nanoparticles (IONPs) may pose exposure risk and adverse health outcomes, biological changes due to occupational exposure remain unexplored. This cross-sectional study recruited 23 workers at a plant that manufactures IONPs and 23 age- and sex-matched controls without metal-rich occupational hazards exposure. Exposure metrics at worksites were monitored, and iron status, oxidation markers, and methylation profiles of genomic DNA in peripheral blood were measured using corresponding enzyme-linked immunosorbent assays and methylation-specific polymerase chain reaction (PCR), respectively. The mass concentration, number counting, and surface area concentration of airborne particles at the worksite significantly increased during the work process of manufacturing/handling IONPs. Overall, compared to controls, workers exhibited increased 5-hydroxymethylcytosine (5hmC) levels without changes in 5-methylcytosine (5mC), hepcidin methylation, iron, soluble transferrin receptor (sTfR), ferritin, hepcidin, 8-hydroxydeoxyguanosine, and glutathione. A positive correlation was found between 5hmC and IONP exposure year with adjustment for age, sex, and cotinine using partial correlation analyses ( r = 0.521, p < 0.001). After stratification of INOPs exposure and 5hmC levels, the univariate general linear model with adjustment for age, sex, and cotinine found that the estimated mean levels of 5mC and sTfR in subjects with low and high 5hmC levels among controls were 11% and 14.4% ( p ≤ 0.01) and 80.9 nM and 70.3 nM ( p < 0.05), respectively. The estimated mean levels of sTfR in workers and controls with low 5hmC levels were 88.3 nM and 68.7 nM ( p ≤ 0.01). Multivariate linear regression analyses suggested an association between sTfR and 5hmC (standardized β = −0.420, p = 0.014) and female sex (standardized β = 0.672, p < 0.001) for subjects with low 5hmC levels. These findings suggest that increased 5hmC could be differentially employed to monitor an epigenetic signature with steady iron homeostasis for occupational IONP-exposed individuals who are likely to experience early but specific decreased sTfR, especially for females concurrent with the onset of increment in 5hmC at low level.

Toxicity and Gene Expression Profiling of Copper- and Titanium-Based Nanoparticles Using Air-Liquid Interface Exposure

To assess the toxicity of nanomaterials, most in vitro studies have been performed under submerged conditions, which do not reflect physiological conditions upon inhalation. An air-liquid interface (ALI) exposure may provide more reliable data on dosimetry and prevent interactions with cell culture media components. Therefore, an ALI exposure was combined with a high-throughput RT-qPCR approach to evaluate the toxicological potential of CuO and TiO₂ nanoparticles (NP) in A549 cells. While TiO₂ NP did not show any cytotoxicity or other effects compromising genomic stability up to 25.8 μg/cm², CuO NP revealed a dose-dependent cytotoxicity, starting at 4.9 μg/cm². Furthermore, CuO NP altered distinct gene expression patterns indicative for disturbed metal homeostasis, stress response, and DNA damage induction. Thus, induction of metal homeostasis associated genes (MT1X, MT2A) at 0.4 μg/cm² and higher suggested uptake and intracellular dissolution of CuO NP, which was verified by a dose-dependent increase in intracellular copper concentration. Starting at 4.9 μg/cm², oxidative stress markers (HMOX1, HSPA1A) were induced dose-dependently, supported by elevated ROS levels. Furthermore, a dose-dependent induction of genes associated with DNA damage response (DDIT3, GADD45A) was observed, in concordance with an increase in DNA strand breaks. Finally, transcriptional data suggested the induction of apoptosis at high doses, while flow cytometric analysis revealed increased numbers of either late apoptotic or necrotic cells and clearly necrotic cells at the highest concentrations. Thus, an ALI cell culture system was successfully combined with a comprehensive high-throughput RT-qPCR system, allowing the quantification of NP deposition and their impact on genomic stability. For CuO NP, in principle the data confirm observations made under submerged conditions with respect to intracellular copper ion release, as well as oxidative and genotoxic stress response. However, the results derived from ALI exposure allow the assessment of dose-response-relationships as well as the comparison of relative toxic potencies of different NP.

Pulmonary toxicity of Fe2O3, ZnFe2O4, NiFe2O4 and NiZnFe4O8 nanomaterials: Inflammation and DNA strand breaks

Exposure to metal oxide nanomaterials potentially occurs at the workplace. We investigated the toxicity of two Fe-oxides: Fe₂O₃ nanoparticles and nanorods; and three MFe₂O₄ spinels: NiZnFe₄O₈, ZnFe₂O₄, and NiFe₂O₄ nanoparticles. Mice were dosed 14, 43 or 128 μg by intratracheal instillation. Recovery periods were 1, 3, or 28 days. Inflammation - neutrophil influx into bronchoalveolar lavage (BAL) fluid - occurred for Fe₂O₃ rods (1 day), ZnFe₂O₄ (1, 3 days), NiFe₂O₄ (1, 3, 28 days), Fe₂O₃ (28 days) and NiZnFe₄O₈ (28 days). Conversion of mass-dose into specific surface-area-dose showed that inflammation correlated with deposited surface area and consequently, all these nanomaterials belong to the so-called low-solubility, low-toxicity class. Increased levels of DNA strand breaks were observed for both Fe₂O₃ particles and rods, in BAL cells three days post-exposure. To our knowledge, this is, besides magnetite (Fe₃O₄), the first study of the pulmonary toxicity of MFe₂O₄ spinel nanomaterials.

The effect of water spray on the release of composite nano-dust

OBJECTIVE

To evaluate the collection efficiency of water spray on the release of airborne composite particles during grinding of composite materials.

MATERIALS AND METHODS

Composite sticks (L:35 mm × W:5.4 mm × H:1.6 mm) of seven commercial dental composites were ground with a rough diamond bur (grain size 100 μm, speed 200,000 rpm). All experiments were performed in an enclosed 1-m³ chamber with low particulate background (< 1,000 #/cm³), and airborne particles were evaluated based on their electrical mobility. The number size distribution was determined by scanning mobility particle sizer (SMPS). Particles were collected by an electrostatic precipitator (ESP), and were ultramorphologically and chemically analyzed by a transmission electron microscope equipped with energy-dispersive X-ray spectroscopy (TEM-EDS).

RESULTS

SMPS measurements confirmed that both dry and wet grinding generated high concentrations of nanoparticles particles with the highest concentration recorded during the last minute of grinding (1.80 × 10⁶ - 3.29 × 10⁶#/cm³), after which a gradual decline in particle concentration took place. Nevertheless, grinding with water spray resulted in a significant reduction of the number of released particles (5.6 × 10⁵ - 1.37 × 10⁶#/cm³). The smallest particle diameter was recorded during the last minute of grinding followed by a continuous growth for every next measurement. TEM of composite dust revealed a high concentration of particles varying in both size and shape.

CONCLUSIONS

Regardless of whether the water cooling spray system was used during bur manipulation of composite materials, predominately nanoparticles were released. However, the particle concentrations were significantly decreased with water spray.

CLINICAL RELEVANCE

Since water spray might not be sufficient in nanoparticle collection, special care should be taken to prevent inhalation of composite dust.

The effect of single and combined exposures to magnetite and polymorphous silicon dioxide nanoparticles on the human A549 cell line: in vitro study

The increasing trend of nanoparticle usage in science and technology has led to significant human exposure. Occupational exposure to iron oxides and silica dust has been reported in mining, manufacturing, construction, and pharmaceutical operations. The combined toxicological effects of nanoparticles and simultaneous exposure to other compounds have given rise to a new concern. Hence, the objective of this study was to investigate the toxicological effects of magnetite and polymorphous silicon dioxide nanoparticles in single and combined exposures. The polymorphous silicon dioxide nanoparticles were obtained from the milled quartz particles under 100 nm in diameter. The milled particles were purified through chloric and nitric acid wash processes. The toxic effects of the magnetite nanoparticles were investigated independently and in combination with quartz using the A₅₄₉ cell line for durations of 24 and 72 h, and using diverse concentrations of 10, 50, 100, and 250 μg/mL. MTT, ROS, mitochondrial membrane potential, and cell glutathione content assays were used to evaluate the amount of cell damage in this study. The statistical significance level in one-way ANOVA and independent t test was considered to be at the 5% confidence level. The size and purity of polymorphous silicon dioxide nanoparticles were measured by TEM and ICP-OES analysis, respectively. The particles' diameters were under 100 nm and demonstrated a purity of higher than 99%. The toxicity results of this study showed a dependency on concentration and exposure duration in reducing the cell viability, cellular glutathione content, and mitochondrial membrane potential, as well as increasing the ROS generation in single and combined exposures with magnetite and polymorphous silicon dioxide nanoparticles. The toxic effects of combined exposure to these nanoparticles were less than the single exposures, and statistically significant antagonistic interactions were detected. Combined exposure to polymorphous silicon dioxide and magnetite nanoparticles, in comparison with their single exposures, could affect health in an antagonistic manner. Since this study has been the first of its kind, further studies investigating the health effects of single and combined exposures to these compounds are needed to verify our findings. Generally, studies such as this one could contribute to the field of combined toxicity effects.

Metal(loid)s urinary level among workers of gas refinery and petrochemical companies: Health risk assessment of metal(loid)s in drinking water and dust

BACKGROUND

Asalouyeh (southern Iran) contains many pollution sources like petrochemical and gas refinery companies. Few studies were conducted on the body burden of metal(loid)s in occupationally exposed workers of the companies in this area.

OBJECTIVES

The urine concentration of metal(loid)s in workers of gas refinery and petrochemical companies in Asalouyeh (who have been worked as "two weeks work-two weeks rest" schedule) was evaluated during a before-and-after observational study. The risks of metal(loid)s in drinking water and dust particles in the studied area were also assessed.

METHODS

Urinary samples (n = 179) were gathered at the first day of two weeks of work (before) and at the end of two weeks of work (after). The concentration of V, Ni, Mn, Cd, and As was measured using a graphite furnace atomic absorption spectrometry. The health hazards of metal(loid)s in the air dust and drinking water of workers were also evaluated.

RESULTS

The median concentration of metal(loid)s for workers of gas refinery and petrochemical companies for before and after two weeks of work was measured, respectively, as: As (11.44 and 9.31 μg/L), Ni (1.06 and 0.51 μg/L), Cd (0.36 and 0.31 μg/L), Mn (0.29 and 0.24 μg/L), and V (0.08 and 0.05 μg/L). After two weeks work, the median of all metal(loid)s in the urine of petrochemical and gas refinery workers was significantly increased. The non-cancer risk due to intake metal(loid)s from drinking water was more than the threshold value and the cancer risk from drinking water and inhaled air dust was less than the threshold.

CONCLUSION

Our results revealed the effect of gas refinery and petrochemical activities on increasing the metal(loid)s concentration of the worker's body and the necessity to protect this group. Additionally, the metal(loid)s intake from drinking water and inhaled dust posed no cancer risk to the workers.

Health risk assessment from exposure to particles during packing in working environments

Packing of raw materials in work environments is a known source of potential health impacts (respiratory, cardiovascular) due to exposure to airborne particles. This activity was selected to test different exposure and risk assessment tools, aiming to understand the effectiveness of source enclosure as a strategy to mitigate particle release. Worker exposure to particle mass and number concentrations was monitored during packing of 7 ceramic materials in 3 packing lines in different settings, with low (L), medium (M) and high (H) degrees of source enclosure. Results showed that packing lines L and M significantly increased exposure concentrations (119-609 μg m^-3 respirable, 1150-4705 μg m^-3 inhalable, 24,755-51,645 cm^-3 particle number), while non-significant increases were detected in line H. These results evidence the effectiveness of source enclosure as a mitigation strategy, in the case of packing of ceramic materials. Total deposited particle surface area during packing ranged between 5.4 and 11.8 × 10⁵ μm² min^-1, with particles depositing mainly in the alveoli (51-64%) followed by head airways (27-41%) and trachea bronchi (7-10%). The comparison between the results from different risk assessment tools (Stoffenmanager, ART, NanoSafer) and the actual measured exposure concentrations evidenced that all of the tools overestimated exposure concentrations, by factors of 1.5-8. Further research is necessary to bridge the current gap between measured and modelled health risk assessments.

Size, composition, morphology, and health implications of airborne incidental metal-containing nanoparticles

There is great concern regarding the adverse health implications of engineered nanoparticles. However, there are many circumstances where the production of incidental nanoparticles, i.e., nanoparticles unintentionally generated as a side product of some anthropogenic process, is of even greater concern. In this study, metal-based incidental nanoparticles were measured in two occupational settings: a machining center and a foundry. On-site characterization of substrate-deposited incidental nanoparticles using a field-portable X-ray fluorescence provided some insights into the chemical characteristics of these metal-containing particles. The same substrates were then used to carry out further off-site analysis including single-particle analysis using scanning electron microscopy and energy-dispersive X-ray spectroscopy. Between the two sites, there were similarities in the size and composition of the incidental nanoparticles as well as in the agglomeration and coagulation behavior of nanoparticles. In particular, incidental nanoparticles were identified in two forms: submicrometer fractal-like agglomerates from activities such as welding and supermicrometer particles with incidental nanoparticles coagulated to their surface, herein referenced as nanoparticle collectors. These agglomerates will affect deposition and transport inside the respiratory system of the respirable incidental nanoparticles and the corresponding health implications. The studies of incidental nanoparticles generated in occupational settings lay the groundwork on which occupational health and safety protocols should be built.

Modeling of High Nanoparticle Exposure in an Indoor Industrial Scenario with a One-Box Model

Mass balance models have proved to be effective tools for exposure prediction in occupational settings. However, they are still not extensively tested in real-world scenarios, or for particle number concentrations. An industrial scenario characterized by high emissions of unintentionally-generated nanoparticles (NP) was selected to assess the performance of a one-box model. Worker exposure to NPs due to thermal spraying was monitored, and two methods were used to calculate emission rates: the convolution theorem, and the cyclic steady state equation. Monitored concentrations ranged between 4.2 × 10⁴–2.5 × 10⁵ cm⁻³. Estimated emission rates were comparable with both methods: 1.4 × 10¹¹–1.2 × 10¹³ min⁻¹ (convolution) and 1.3 × 10¹²–1.4 × 10¹³ min⁻¹ (cyclic steady state). Modeled concentrations were 1.4-6 × 10⁴ cm⁻³ (convolution) and 1.7–7.1 × 10⁴ cm⁻³ (cyclic steady state). Results indicated a clear underestimation of measured particle concentrations, with ratios modeled/measured between 0.2–0.7. While both model parametrizations provided similar results on average, using convolution emission rates improved performance on a case-by-case basis. Thus, using cyclic steady state emission rates would be advisable for preliminary risk assessment, while for more precise results, the convolution theorem would be a better option. Results show that one-box models may be useful tools for preliminary risk assessment in occupational settings when room air is well mixed.

Evacuation characteristics of released airborne TiO2 nanomaterial particles under different ventilation rates in a confined environment

A specially designed 32 m³ airtight chamber that allows the implementation of various ventilation strategies was utilised to study the evacuation characteristics of airborne sub-micron particles generated from TiO₂ nanopowder in a potential indoor accidental release situation. Following the release using a heated line from a nebuliser system, the spatial and temporal variations in particle number concentration were recorded by three condensation particle counters (CPCs) distributed at specific locations in the chamber. A differential mobility spectrometer was co-located with one of the CPCs for the measurement of particle size distributions (PSDs). The different modal groups present within the measured PSDs were determined through a log₁₀-normal fitting program. Of the ventilation rates evaluated, the greatest relative improvement in particle concentration and clearance time occurred at the highest rate (12 air changes per hour, ACH). At the same time, indications of cross-contamination from regions with strong mixing conditions to regions where mixing was poor, were obtained showing that the latter could operate as particle traps where localised poor ventilation might occur. However, reducing the ventilation rate led to: i) an increase of leftover particles in the air of the chamber when the cleaning process had been completed, and more specifically to an increased ratio of ultrafine particles over fine ones, resulting in the potentially dangerous accumulation of contaminants with high exposure hazards, ii) a decrease in ventilation efficiency, which at low evacuation rates became independent of distance from the inlet diffuser, iii) slower clearance of resuspended particles, with the lowest efficiency at the moderate ventilation rate.

Three-Dimensional Quantitative Co-Mapping of Pulmonary Morphology and Nanoparticle Distribution with Cellular Resolution in Nondissected Murine Lungs

Deciphering biodistribution, biokinetics, and biological effects of nanoparticles (NPs) in entire organs with cellular resolution remains largely elusive due to the lack of effective imaging tools. Here, light sheet fluorescence microscopy in combination with optical tissue clearing was validated for concomitant three-dimensional mapping of lung morphology and NP biodistribution with cellular resolution in nondissected ex vivo murine lungs. Tissue autofluorescence allowed for label-free, quantitative morphometry of the entire bronchial tree, acinar structure, and blood vessels. Co-registration of fluorescent NPs with lung morphology revealed significant differences in pulmonary NP distribution depending on the means of application (intratracheal instillation and ventilator-assisted aerosol inhalation under anesthetized conditions). Inhalation exhibited a more homogeneous NP distribution in conducting airways and acini indicated by a central-to-peripheral (C/P) NP deposition ratio of unity (0.98 ± 0.13) as compared to a 2-fold enhanced central deposition (C/P = 1.98 ± 0.37) for instillation. After inhalation most NPs were observed in the proximal part of the acini as predicted by computational fluid dynamics simulations. At cellular resolution patchy NP deposition was visualized in bronchioles and acini, but more pronounced for instillation. Excellent linearity of the fluorescence intensity-dose response curve allowed for accurate NP dosimetry and revealed ca. 5% of the inhaled aerosol was deposited in the lungs. This single-modality imaging technique allows for quantitative co-registration of tissue architecture and NP biodistribution, which could accelerate elucidation of NP biokinetics and bioactivity within intact tissues, facilitating both nanotoxicology studies and the development of nanomedicines.

Testing the performance of one and two box models as tools for risk assessment of particle exposure during packing of inorganic fertilizer

Modelling of particle exposure is a useful tool for preliminary exposure assessment in workplaces with low and high exposure concentrations. However, actual exposure measurements are needed to assess models reliability. Worker exposure was monitored during packing of an inorganic granulate fertilizer at industrial scale using small and big bags. Particle concentrations were modelled with one and two box models, where the emission source was estimated with the fertilizer's dustiness index. The exposure levels were used to calculate inhaled dose rates and test accuracy of the exposure modellings. The particle number concentrations were measured from worker area by using a mobility and optical particle sizer which were used to calculate surface area and mass concentrations. The concentrations in the worker area during pre-activity ranged 63,797-81,073 cm^-3, 4.6 × 10⁶ to 7.5 × 10⁶ μm² cm^-3, and 354 to 634 μg m^-3 (respirable mass fraction) and during packing 50,300 to 85,949 cm^-3, 4.3 × 10⁶ to 7.6 × 10⁶ μm² cm^-3, and 279 to 668 μg m^-3 (respirable mass fraction). Thus, the packing process did not significantly increase the exposure levels. Chemical exposure was also under control based on REACH standards. The particle surface area deposition rate in respiratory tract was up to 7.6 × 10⁶ μm² min^-1 during packing, with 52%-61% of deposition occurring in the alveolar region. Ratios of the modelled and measured concentrations were 0.98 ± 0.19 and 0.84 ± 0.12 for small and big bags, respectively, when using the one box model, and 0.88 ± 0.25 and 0.82 ± 0.12, when using the two box model. The modelling precision improved for both models when outdoor particle concentrations were included. This study shows that exposure concentrations in a low emission industrial scenario, e.g. during packing of a fertilizer, can be predicted with a reasonable accuracy by using the concept of dustiness and mass balance models.

Fast and simple assessment of surface contamination in operations involving nanomaterials

The deposition of airborne nanosized matter onto surfaces could pose a potential risk in occupational and environmental scenarios. The incorporation of fluorescent labels, namely fluorescein isotiocyanate (FITC) or tris-1,3-phenanthroline ruthenium (II) chloride (Ru(phen)₃Cl₂), into spherical 80-nm silica nanoparticles allowed the detection after the illumination with LED light of suitable wavelength (365 or 405 nm respectively). Monodisperse nanoparticle aerosols from fluorescently labeled nanoparticles were produced under safe conditions using powder generators and the deposition was tested into different surfaces and filtering media. The contamination of gloves and work surfaces that was demonstrated by sampling and SEM analysis becomes immediately clear under laser or LED illumination. Furthermore, nanoparticle aerosols of about 10⁵ nanoparticles/cm³ were alternatively fed through a glass pipe and personal protective masks to identify the presence of trapped nanoparticles under 405 nm or 365 nm LED light. This testing procedure allowed a fast and reliable estimation of the contamination of surfaces with nanosized matter, with a limit of detection based on the fluorescence emission of the accumulated solid nanoparticles of 40 ng of Ru(phen)₃@SiO₂ of silica per mg of non-fluorescent matter.

Environmental impacts of nanomaterials

Nanotechnology is currently one of the highest priority research fields in many countries due to its immense potentiality and economic impact. Nanotechnology involves the research, development, production, and processing of structures and materials on a nanometer scale in various fields of science, technology, health care, industries, and agriculture. As such, it has contributed to the gradual restructuring of many associated technologies. However, due to the uncertainties and irregularities in shape, size, and chemical compositions, the presence of certain nanomaterials may exert adverse impacts on the environment as well as human health. Concerns have thus been raised about the destiny, transport, and transformation of nanoparticles released into the environment. A critical evaluation of the current states of knowledge regarding the exposure and effects of nanomaterials on the environment and human health is discussed in this review. Recognition on the potential advantages and unintended dangers of nanomaterials to the environment and human health is critically important to pursue their development in the future.

Nanoparticle decoration impacts airborne fungal pathobiology

Airborne fungal pathogens, predominantly Aspergillus fumigatus, can cause severe respiratory tract diseases. Here we show that in environments, fungal spores can already be decorated with nanoparticles. Using representative controlled nanoparticle models, we demonstrate that various nanoparticles, but not microparticles, rapidly and stably associate with spores, without specific functionalization. Nanoparticle-spore complex formation was enhanced by small nanoparticle size rather than by material, charge, or "stealth" modifications and was concentration-dependently reduced by the formation of environmental or physiological biomolecule coronas. Assembly of nanoparticle-spore surface hybrid structures affected their pathobiology, including reduced sensitivity against defensins, uptake into phagocytes, lung cell toxicity, and TLR/cytokine-mediated inflammatory responses. Following infection of mice, nanoparticle-spore complexes were detectable in the lung and less efficiently eliminated by the pulmonary immune defense, thereby enhancing A. fumigatus infections in immunocompromised animals. Collectively, self-assembly of nanoparticle-fungal complexes affects their (patho)biological identity, which may impact human health and ecology.

Association of ultrafine particles with cardiopulmonary health among adult subjects in the urban areas of northern Taiwan

The association between short-term exposure to particulate air pollution, especially fine particles, and cardiopulmonary health has been well-established in previous studies. However, previous findings regarding the effect of ultrafine particles (UFPs) on cardiopulmonary health are inconsistent. We repeatedly measured the mass concentrations of UFPs using a Micro-Orifice Uniform Deposit Impactor (MOUDI) in the apartments of 100 adult participants and collected the participants' health data from the pulmonary outpatient unit of Shuang-Ho Hospital to investigate the association between short-term exposure to UFPs and cardiopulmonary health using mixed-effects models from January 1, 2014 to August 31, 2017. We also collected ambient air pollution monitoring data from the Taiwan Environmental Protection Administration for data analysis. We observed that an interquartile range increase in the 24-hour mean UFPs (0.97 μg/m³) was associated with a 6.3% [95% confidence interval (CI) = 2.9, 9.7], 5.6% (95% CI = 4.1, 7.1) and 8.5% (95% CI = 3.9, 13.1) increase in systolic blood pressure, diastolic blood pressure and high sensitivity-C-reactive protein, respectively. We also observed the association of particulate matter less than or equal to 2.5 μm in diameter and nitrogen dioxide with increased blood pressure and ozone with decreased lung function. A negative trend between UFPs and forced expiratory volume in the first second was observed. We concluded that short-term exposure to UFPs was associated with cardiovascular health in adult subjects in the urban areas of northern Taiwan.

A versatile generator of nanoparticle aerosols. A novel tool in environmental and occupational exposure assessment

The increasing presence of nanotechnology on the market entails a growing probability of finding ENMs in the environment. Nanoparticles aerosols are a yet unknown risk for human and environmental exposure that may normally occur at any point during the nanomaterial lifecycle. There is a research gap in standardized methods to assess the exposure to airborne nanoparticles in different environments. The controllable generation of nanoparticle aerosols has long been a challenging objective for researchers and industries dealing with airborne nanoparticles. In this work, a versatile system to generate nanoparticulate aerosols has been designed. The system allows the production of both i) instantaneous nanoparticle clouds and ii) continuous nanoparticle streams with quasi-stable values of particle concentration and size distribution. This novel device uses a compressed-air pressure pulse to disperse the target material into either the testing environment (instantaneous cloud formation) or a secondary chamber, from which a continuous aerosol stream can be drawn, with a tunable nanoparticle concentration. The system is robust, highly versatile and easy to operate, enabling reproducible generation of aerosols from a variety of sources. The system has been verified with four dry nanomaterials: TiO₂, ZnO, CuO and CNT bundles.

A review of the fate of engineered nanomaterials in municipal solid waste streams

Significant knowledge and data gaps associated with the fate of product-embedded engineered nanomaterials (ENMs) in waste management processes exist that limit our current ability to develop appropriate end-of-life management strategies. This review paper was developed as part of the activities of the IWWG ENMs in Waste Task Group. The specific objectives of this review paper are to assess the current knowledge associated with the fate of ENMs in commonly used waste management processes, including key processes and mechanisms associated with ENM fate and transport in each waste management process, and to use that information to identify the data gaps and research needs in this area. Literature associated with the fate of ENMs in wastes was reviewed and summarized. Overall, results from this literature review indicate a need for continued research in this area. No work has been conducted to quantify ENMs present in discarded materials and an understanding of ENM release from consumer products under conditions representative of those found in relevant waste management process is needed. Results also indicate that significant knowledge gaps associated with ENM behaviour exist for each waste management process investigated. There is a need for additional research investigating the fate of different types of ENMs at larger concentration ranges with different surface chemistries. Understanding how changes in treatment process operation may influence ENM fate is also needed. A series of specific research questions associated with the fate of ENMs during the management of ENM-containing wastes have been identified and used to direct future research in this area.

Nanomaterial exposure, toxicity, and impact on human health

The use of engineered nanomaterials (ENM) has grown after the turn of the 21st century. Also, the production of ENM has globally grown, and exposure of workers especially via the lungs to ENM has increased. This review tackles with effects of ENM on workers' health because occupational environment is the main source of exposure to ENM. Assessment of exposure to ENM is demanding, and today there are no occupational exposure level (OEL) for ENM. This is partly due to challenges of such measurements, and in part to the unknown causality between ENM metrics and effects. There are also marked gaps in systematic knowledge on ENM hazards. Human health surveys of exposed workers, or human field studies have not identified specific effects of ENM linking them with a specific exposure. There is, however, a consensus that material characteristics such as size, and chemistry influence effects of ENM. Available data suggest that multiwalled carbon nanotubes (MWCNT) affect the immunological system and cause inflammation of the lungs, or signs of asthma whereas carbon nanofibers (CNF) may cause interstitial fibrosis. Metallic and metal oxide nanoparticles together with MWCNT induce genotoxicity, and a given type of MWCNT has been identified as a possible human carcinogen. Currently, lack of understanding of mechanisms of effects of ENM renders assessment of hazards and risks of ENM material-by-material a necessity. The so called "omics" approaches utilizing ENM-induced alterations in gene and protein expression may be useful in the development of a new paradigm for ENM hazard and risk assessment. This article is categorized under: Toxicology and Regulatory Issues in Nanomedicine > Toxicology of Nanomaterials.

Particle release and control of worker exposure during laboratory-scale synthesis, handling and simulated spills of manufactured nanomaterials in fume hoods

Fume hoods are one of the most common types of equipment applied to reduce the potential of particle exposure in laboratory environments. A number of previous studies have shown particle release during work with nanomaterials under fume hoods. Here, we assessed laboratory workers' inhalation exposure during synthesis and handling of CuO, TiO₂ and ZnO in a fume hood. In addition, we tested the capacity of a fume hood to prevent particle release to laboratory air during simulated spillage of different powders (silica fume, zirconia TZ-3Y and TiO₂). Airborne particle concentrations were measured in near field, far field, and in the breathing zone of the worker. Handling CuO nanoparticles increased the concentration of small particles (< 58 nm) inside the fume hood (up to 1 × 10⁵ cm^-3). Synthesis, handling and packaging of ZnO and TiO₂ nanoparticles did not result in detectable particle release to the laboratory air. Simulated powder spills showed a systematic increase in the particle concentrations inside the fume hood with increasing amount of material and drop height. Despite powder spills were sometimes observed to eject into the laboratory room, the spill events were rarely associated with notable release of particles from the fume hood. Overall, this study shows that a fume hood generally offers sufficient exposure control during synthesis and handling of nanomaterials. An appropriate fume hood with adequate sash height and face velocity prevents 98.3% of particles release into the surrounding environment. Care should still be made to consider spills and high cleanliness to prevent exposure via resuspension and inadvertent exposure by secondary routes.