Sorption and retention of diclofenac on zeolite in the presence of cationic surfactant

Removal of diclofenac by adsorption process studied in free-base porphyrin Zr-metal organic frameworks (Zr-MOFs)

As the world population continues to grow, there is also a rising concern regarding water pollution since this condition could negatively impact the supply of clean water. One of the most recent concerns is related to the pollution that comes from various pharmaceuticals, in particular non-steroidal anti-inflammatory drugs (NSAIDs) since they have been industrially produced at large scale and can be easily purchased as an over-the-counter medicine. Diclofenac is one of the most popular NSAIDs because of its high-effectiveness, which leads to its excessive consumption. Consequently, its presence in water bodies is also continuously increasing. An adsorption process could then be employed as a highly effective method to address this issue. In comparison to other conventional adsorbents such as activated carbon, the use of metal-organic frameworks (MOFs) as an alternative adsorbent is very attractive since it can offer various advantages such as tailorability and high adsorption capacity. In this study, the performance of three water-stable, free-base porphyrin MOFs assembled using zirconia-based nodes, namely MOF-525, MOF-545, and NU-902, for diclofenac adsorption was thoroughly investigated. Interestingly, although all three free-base porphyrin MOFs are assembled using the same building block and have a similar specific surface area (based on the experimental argon physisorption and calculation based on non-localized density functional theory), their diclofenac adsorption capacity is substantially different from one another. It is found that the highest diclofenac adsorption capacity is shown by MOF-525, which has maximum capacity around 792 mg g^-1. This is then followed by MOF-545 and NU-902 that have adsorption capacities around 591 and 486 mg g^-1, respectively. Some possible adsorption mechanisms are then thoroughly discussed that might contribute to this phenomenon. Lastly, their performance is also compared with other MOFs that are also studied for this purpose to show their performance superiority not only in terms of adsorption capacity but also their affinity towards the diclofenac molecule, which might be useful as an adsorption performance indicator in the real condition where the contaminant concentration is considerably low.

Synergistic effects of binary surfactant mixtures in the adsorption of diclofenac sodium drug from aqueous solution by modified zeolite

In this paper, the surfactant-modified clinoptilolite zeolite (with two methods) were used to remove diclofenac sodium (DFS) as a widely used drug in an aqueous solution. Clinoptilolite was modified by using pure cationic surfactant (cetyltrimethylammonium chloride, CTAC) and the mixed surfactants of CTAC + Triton-X100 (TX100). In the new approach, the synergistic effects between CTAC and TX100 were determined by surface tension measurements in different mole fractions and the optimum ratio (y₁ ≈ 0.8) was identified with the maximum synergism. According to the mole fraction of this composition, the surface of clinoptilolite was modified by mixed surfactants (MSMZ) for the adsorption of DFS and then results compared with modified zeolite with pure cationic surfactant (SMZ). The raw and modified (SMZ and MSMZ) zeolites were characterized by Fourier transform infrared spectroscopy (FT-IR), BET analysis, the scanning electron microscopy (SEM) images, Zeta potential and X-ray. The experimental data of adsorption in equilibrium conditions were also analyzed using different adsorption isotherm models (Langmuir, Freundlich, Hill, Khan, Sips, Redlich-Peterson and Toth) in non-linear forms, and finally, the best model consistent with experimental data is determined (SMZ:Sips and MSMZ:Toth). According to the best isotherm model, the amount of absorption capacity in MSMZ was obtained almost 57% higher than SMZ. In addition, the kinetic adsorption data were correlated with eight various models in order to selection the best model for these systems. The kinetic adsorption data were well described by fractal-like pseudo-first-order (FL-PFO) and IKL models for SMZ and MSMZ adsorbents, respectively. Eight error functions were used to estimate the best fitted isotherm and kinetic models.

Influence of the Type and the Amount of Surfactant in Phillipsite on Adsorption of Diclofenac Sodium

Modified phillipsite samples were prepared with two different amounts (monolayer and bilayer coverage) of surfactants octadecyldimethylbenzylammonium chloride (O) and dodecylamine (D). Composites were characterized by Fourier transform infrared spectroscopy with attenuated total reflectance (FTIR–ATR), thermal analysis and determination of zeta potential, and subsequently tested for removal of diclofenac sodium (DCF). Drug adsorption experiments were performed under different initial DCF concentrations and different contact times. In order to investigate the influence of the chemical structure of surfactants used for modification of phillipsite on the preparation and properties of composites and DCF adsorption, experimental data were compared with previously published results on DCF adsorption by composites containing phillipsite and the same amounts of surfactants cetylpyridinium chloride (C) and Arquad®2HT-75 (A). DCF adsorption isotherms for O and D composites showed a better fit with the Langmuir model with maximum adsorption capacities between 12.3 and 38.4 mg/g and are similar to those for C and A composites, while kinetics run followed a pseudo-second-order model. Composites containing either benzyl or pyridine functional groups showed higher adsorption of DCF, implying that surfactant structure has a significant impact on drug adsorption. Drug adsorption onto O, D, C and A composites was also confirmed by FTIR–ATR spectroscopy and zeta potential measurements.

Application of Surfactant Modified Natural Zeolites for the Removal of Salicylic Acid-A Contaminant of Emerging Concern

This work aimed to test composites (surfactant modified zeolites prepared by treatment of natural zeolites—clinoptilolite (IZ CLI) and/or phillipsite (PHIL75)-rich tuffs with two different amounts of cationic surfactants: cetylpyridinium chloride (CPyCl) and Arquad^® 2HT-75 (ARQ)) for the adsorption of salicylic acid (SA)—a common contaminant of emerging concern. Adsorption of SA was studied at different initial drug concentrations (in the range of 2–100 mg/L) in water solution. The Langmuir isotherm model showed the highest adsorption was achieved by bilayer composite of IZ CLI and CPyCl—around 11 mg/g. Kinetic runs were performed by using the initial drug concentration of 20 mg/L in the time interval from 0 to 75 min and pseudo-second order had good correlation with experimental data. The influence of the four different temperatures on the SA adsorption was also investigated and thermodynamic parameters suggested that the adsorption drug onto composites is an exothermic and nonspontaneous process, followed by the decrease of randomness at the solid/liquid interface during the adsorption. Zeta potential and Fourier-transform infrared spectroscopy with attenuated total reflectance (FTIR-ATR) had been performed for the characterization of composites after adsorption of SA confirming the presence of the drug at composite surfaces.

Mechanistic interaction of ciprofloxacin on zeolite modified seaweed (Sargassum crassifolium) derived biochar: Kinetics, isotherm and thermodynamics

Modification of biochar for efficient removal of antibiotics from water could be a valuable approach in the environmental applications. In this study, a brown seaweed (Sargassum crassifolium) was pyrolyzed at 500 °C and the obtained biochar (SWBC) was modified with zeolite through the slurry method maintaining the ratio at 1:5 (zeolite: biochar) (SWBC-Z). Batch adsorption experiments were conducted to evaluate the adsorption tendency of SWBC and SWBC-Z for the removal of ciprofloxacin (CPX) from water via pH edge, kinetics, isotherm and thermodynamic experiments. The highest adsorption was in the pH range of 6.5-8, supported by the electrostatic attractions and hydrogen bonding with zwitterionic CPX. Experimental kinetics data was well-fitted to the pseudo-second-order and Elovich models (R2 of 0.992 and 0.976, respectively), while the Langmuir and Freundlich isotherm models best described the isotherm data (R2 of 0.954 and 0.976, respectively). The maximum adsorption capacity of 93.65 mg g-1 was recorded for the SWBC-Z. The models predicted chemisorption and physisorption interactions on the heterogenous biochar surface. Well-defined peaks of silanol groups in the FTIR spectrum of SWBC-Z and its electron microscopy confirmed the incorporation of zeolite minerals. Post adsorption FTIR analysis elucidated the changes in the surface functional groups of the SWBC-Z. Thermodynamic data revealed spontaneous and exothermic reaction between CPX and both the biochars. It was concluded that modification of pristine biochar with zeolite imparted greater surface area and additional active sites, which subsequently enhanced the overall CPX adsorption by the SWBC-Z.

Removal of non-steroidal anti-inflammatory drugs from water by zeolite-rich composites: The interference of inorganic anions on the ibuprofen and naproxen adsorption

Composites of two natural zeolites - clinoptilolite and phillipsite, and cationic surfactants (cetylpyridinium chloride and Arquad® 2HT-75) were tested for the removal of two emerging contaminants - ibuprofen and naproxen. For each zeolite-rich rock, two different modifications of the zeolitic surfaces were prepared (monolayer and bilayer surfactant coverage). The influence of the initial drug concentrations and contact time on adsorption of these drugs was followed in buffer solution. The Langmuir model showed the highest adsorption capacity for the composite characterized by a bilayered surfactant at the clinoptilolite surface: 19.7 mg/g and 16.1 mg/g for ibuprofen and naproxen, respectively. Also, to simulate real systems, drug adsorption isotherms were conducted in natural water (Grindstone creek water - Columbia, Missouri, USA) by using the best performing adsorbent; in this case, a slight decrease of drug adsorption was recorded. Kinetic runs were performed in distilled water as well as in the presence of ions such as sulfates and bicarbonates; also, in this case, the interfering agents defined an adsorption decrease for bilayer composites.

Removal of Carbamazepine onto Modified Zeolitic Tuff in Different Water Matrices: Batch and Continuous Flow Experiments

Carbamazepine (CBZ) is the most frequently detected pharmaceutical residues in aquatic environments effluent by wastewater treatment plants. Batch and column experiments were conducted to evaluate the removal of CBZ from ultra-pure water and wastewater treatment plant (WWTP) effluent using raw zeolitic tuff (RZT) and surfactant modified zeolite (SMZ). Point zero net charge (pHpzc), X-ray diffraction (XRD), X-ray fluorescence (XRF), and Fourier Transform Infrared (FTIR) were investigated for adsorbents to evaluate the physiochemical changes resulted from the modification process using Hexadecyltrimethylammonium bromide (HDTMA-Br). XRD and FTIR showed that the surfactant modification of RZT has created an amorphous surface with new alkyl groups on the surface. The pHpzc was determined to be approximately 7.9 for RZT and SMZ. The results indicated that the CBZ uptake by SMZ is higher than RZT in all sorption tests (>8 fold). Batch results showed that the sorption capacity of RZT and SMZ in WWTP effluent (0.029 and 0.25 mg/g) is higher than RZT and SMZ (0.018 and 0.14 mg/g) in ultrapure water (1.6–1.8 fold). Batch tests showed that the equilibrium time of CBZ removal in the WWTP matrix (47 h) is much longer than CBZ removal in ultrapure water. The sorption capacity of RZT & SMZ in WWTP effluent (0.03, 0.33 mg/g) is higher than RZT and SMZ (0.02 and 0.17 mg/g) in ultrapure water (1.5–2 fold) using column test. This study has clearly demonstrated that the performance of RZT and SMZ is more efficient for the removal of CBZ from realistic wastewater than ultrapure water. It is evident that the surfactant modification of RZT has enhanced the CBZ removal in both matrices.

Removal of Salicylic and Ibuprofen by Hexadecyltrimethylammonium-Modified Montmorillonite and Zeolite

The removal of salicylic acid (SA) and ibuprofen (IB) by sorption onto HDTMA-modified montmorillonite (HM) and zeolite (HZ) was investigated at pH 7. The single sorption data were fitted well by the Freundlich, Langmuir, Dubinin−Radushkevich (DR), and Polanyi−Dubinin−Manes (PDM) models (R2 > 0.94). The sorption affinity of Freundlich and the maximum sorption capacity of Langmuir and PDM models of pharmaceuticals onto HM were consistently higher than that of HZ mainly owing to the higher organic carbon content. In addition, the KF, qmL, and qm values were in the order of IB > SA owing to higher hydrophobicity and molar volume. Since the predominant speciation of SA and IB is anionic at pH 7 (>pKa), sorption onto HM occurs mainly by the two-dimensional surface adsorption onto the pseudo-organic medium in the HM, whereas the interaction of anionic pharmaceuticals with the positively charged “head” of HDTMA is responsible for HZ. Sorption isotherms were fitted well by the PDM model, which indicated that pore-filling was one of the dominating sorption mechanisms. The extended Langmuir model, modified Langmuir competitive model, and ideal adsorbed solution theory employed with Freundlich and Langmuir sorption models were applied to predict binary sorption. The effect of competition between the solutes was clearly evident in the characteristic curves; the maximum sorbed volume (qv.m) was reduced, and the sorbed volume (qv) had a wider distribution toward the sorption potential density.

New Eco-Materials Derived from Waste for Emerging Pollutants Adsorption: The Case of Diclofenac

This work proposes new eco-materials for the adsorption of diclofenac (DCF). The large consumption of this nonsteroidal anti-inflammatory drug combined with the inefficiency of wastewater treatment plants (WWTPs) leads to its presence in aquatic environments as an emerging pollutant. The adsorption technique is widely used for pharmaceutical removal. Moreover, due to the large effect of commercial adsorbents, in the frame of the Azure Chemistry approach, new sustainable materials are mandatory for removal as emerging pollutants. The work proposes three adsorbents that were obtained from different stabilization methods of fly ash derived from an incinerator plant; the stabilization techniques involved the use of various industrial by-products such as bottom ash, flue gas desulphurization residues, coal fly ash, and silica fume. The best performance, although less than activated carbon, was obtained by COSMOS (COlloidal Silica Medium to Obtain Safe inert: the case of incinerator fly ash), with a removal efficacy of approximately 76% with 15 g/L of material. Several advantages are expected not only from the DCF removal but also from an economic perspective (the newly obtained adsorbents are eco-materials, so they are cheaper in comparison to conventional adsorbents) and in terms of sustainability (no toxic reagents and no heating treatment are involved). This work highlights the adsorption performance of the new eco-materials and their potential use in WWTPs.

Monitoring diclofenac adsorption by organophilic alkylpyridinium bentonites

Organoclays have been applied as efficient adsorbents for pharmaceutical pollutants from aqueous solution. In this work, dodecylpyridinium chloride (C₁₂pyCl) and hexadecylpyridinium chloride (C₁₆pyCl) cationic surfactants were used for the preparation of organobentonites destined for diclofenac sodium (DFNa) adsorption, an anionic drug widely detected in wastewater. The organofunctionalization of the clay samples was performed under microwave irradiation at 50 °C for 5 min with surfactant amounts of 100% and 200% in relation to the cation exchange capacity (CEC) of the pristine bentonite. The amount of incorporated ammonium salts based on CHN elemental analysis was higher for all samples prepared with 200% of the CEC. The basal spacings of the organoclays ranged from 1.54 to 2.13 nm, indicating the entrance of organic cations into the interlayer spacing of the clay samples, and the spacing depended on the size of the alkyl organic chain. The hydrophobic character of the organobentonites was verified by thermogravimetry and infrared spectroscopy (FTIR). The adsorption isotherms showed that the drug capacity adsorption was influenced by the amount of surfactant incorporated into the bentonite, the packing density and the arrangement of the surfactants in the interlayer spacing. Zeta potential measurements of the organobentonites and FTIR analysis after drug adsorption suggested that electrostatic and nonelectrostatic interactions contributed to the mechanism of adsorption.

Slovak natural zeolites as a suitable medium for antibiotics elimination from wastewater

Pharmaceuticals are one of the most used compounds present in various environmental compartments. Due to their high consumption and possible unhealthy effect on ecosystems, pharmaceuticals have been identified as “emerging organic contaminants”. Since these compounds have medium to high polarity, they end up in the water compartment after being used. This work deals with the sorption of three pharmaceutical substances from the therapeutic group of antibiotics. Specifically we have focused on Azithromycin, Clarithromycin and Erythromycin. Three fractions of the natural Slovak zeolites (200 μm, 0.5—1 mm and 1.5—2 mm) were used as the sorption medium. Experimental results have proven very effective sorption of antibiotics by zeolites. Azithromycin removal of over 99 % for all three zeolite fractions from wastewater treatment plant Stupava and wastewater treatment plant Devínska Nová Ves was achieved. Clarithromycin removal of 79 % for fraction 1—2.5 mm, 87.3 % for fraction 0.5—1 mm and of 99.8 % for fraction 200 μm from the effluent of wastewater treatment plant Stupava was observed. Erythromycin removal of 31.3 % for fraction 1—2.5 mm, 66.9 % for fraction 0.5—1mm and of 94.7 % for fraction 200 μm from effluent of wastewater treatment plant Stupava was measured. More than 95 % of Clarithromycin and Erythromycin were eliminated from the effluent of wastewater treatment plant Devínska Nová Ves. The highest elimination percentage was observed for the smallest zeolite fraction due to the highest specific surface area.

Synthesis and Characterization of Halloysite/Carbon Nanocomposites for Enhanced NSAIDs Adsorption from Water

The adsorption of ketoprofen, naproxen, and diclofenac (non-steroidal anti-inflammatory drugs, NSAIDs) on halloysite/carbon nanocomposites and non-modified halloysite were investigated in this work. Halloysite/carbon nanocomposites were obtained through liquid phase impregnation and carbonization using halloysite as the template and saccharose as the carbon precursor. Scanning electron microscopy (SEM), X-ray diffraction (XRD), Fourier-transform infrared spectrometry (FT-IR), and low-temperature nitrogen adsorption method were employed to study the morphological and structural changes of the halloysite/carbon nanocomposites. The effects of contact time, initial concentration of adsorbates, pH of solution, and mass of adsorbent on the adsorption were studied. Adsorption mechanism was found to fit pseudo-second-order and intra-particle diffusion models. The obtained experimental adsorption data were well represented by the Langmuir multi-center adsorption model. Adsorption ability of halloysite/carbon nanocomposites was much higher for all the studied NSAIDs in comparison to non-modified halloysite. Optimized chemical structures of ketoprofen, naproxen, and diclofenac obtained by Density Functional Theory (DFT) calculation showed that charge distributions of these adsorbate molecules and their ions can be helpful to explain the details of adsorption mechanism of NSAIDs on halloysite/carbon nanocomposites.

Facile Synthesis of Porous Carbon for the Removal of Diclofenac Sodium from Water

In this work, a series of porous carbon materials (PCs) were obtained at different carbonization temperatures (800, 900, 1000, and 1100 °C) by a simple and fast solvent-free method. Moreover, the feasibility of PCs as reliable and efficient adsorbents to capture diclofenac sodium (DCF) from the water was evaluated. Notably, porous carbon (PC) prepared at 1000 °C (PC-1000) was found to be the best candidate for the adsorption of DCF. Remarkably, adsorption equilibrium was achieved within 3 h, which followed a pseudo-second-order kinetic model with a high correlation coefficient (R ² > 0.994). Furthermore, experimental data obtained from adsorption isotherm indicated that the capture of DCF onto PC-1000 followed the Langmuir adsorption model (R ² > 0.997), wherein its maximum adsorption capacity was calculated to be 392 mg/g. In addition, based on the results obtained from the zeta potential of PC-1000 under different pH and the adsorbed quantity of DCF along with functional groups created on the surface of PC-1000, electrostatic and H-bonding interactions were proposed as the possible adsorption mechanisms. Due to its high stability and excellent reusability, PC-1000 has been testified as a promising candidate for removing DCF from contaminated water.

Ag3PO4 Deposited on CuBi2O4 to Construct Z-Scheme Photocatalyst with Excellent Visible-Light Catalytic Performance Toward the Degradation of Diclofenac Sodium

CuBi₂O₄/Ag₃PO₄ was synthesized through a combination of hydrothermal synthesis and an in situ deposition method with sodium stearate as additives, and their textures were characterized with XRD, XPS, SEM/HRTEM, EDS, UV-Vis, and PL. Then, the photodegradation performance of CuBi₂O₄/Ag₃PO₄ toward the degradation of diclofenac sodium (DS) was investigated, and the results indicate that the degradation rate of DS in a CuBi₂O₄/Ag₃PO₄ (1:1) system is 0.0143 min⁻¹, which is 3.6 times that in the blank irradiation system. Finally, the photocatalytic mechanism of CuBi₂O₄/Ag₃PO₄ was discussed, which follows the Z-Scheme theory, and the performance enhancement of CuBi₂O₄/Ag₃PO₄ was attributed to the improved separation efficiency of photogenerated electron–hole pairs.

A Study on the Removal of Copper (II) from Aqueous Solution Using Lime Sand Bricks

Heavy metals such as Cu(II), if ubiquitous in the runoff, can have adverse effects on the environment and human health. Lime sand bricks, as low-cost adsorbents to be potentially applied in stormwater infiltration facilities, were systematically investigated for Cu(II) removal from water using batch and column experiments. In the batch experiment, the adsorption of Cu(II) to bricks reach an equilibrium within 7 h and the kinetic data fits well with the pseudo-second-order model. The sorption isotherm can be described by both the Freundlich and Langmuir model and the maximum adsorption capacity of the bricks is 7 ± 1 mg/g. In the column experiment, the best removal efficiency for Cu(II) was observed at a filler thickness of 20 cm, service time of 12 min with a Cu(II) concentration of 0.5 mg/L. The Cu(II) removal rate increases with the increasing bed depth and residence time. The inlet concentration and residence time had significant effects on the Cu(II) removal analyzed by the Box–Behnken design (BBD). The Adams-Bohart model was in good agreement with the experimental data in representing the breakthrough curve. Copper fractions in the bricks descend in the order of organic matter fraction > Fe-Mn oxides fraction > carbonates fraction > residual fraction > exchangeable fraction, indicating that the lime sand bricks after copper adsorption reduce the long-term ecotoxicity and bioavailability to the environment.

Novel nanofibers mat as an efficient, fast and reusable adsorbent for solid phase extraction of non-steroidal anti-inflammatory drugs in environmental water

Core-shell polyaniline/polyacrylonitrile nanofibers mat (PANI/Pan NFsM) was prepared for extraction of hydrophilic non-steroidal anti-inflammatory drugs (NSAIDs) in environmental water. Superior adsorption and desorption performance of PANI/Pan NFsM was confirmed by both static and dynamic adsorption/desorption experiments. These properties proved PANI/Pan NFsM was a potentially efficient and fast solid phase extraction (SPE) adsorbent for NSAIDs. Under the optimized conditions, only 3 mg of PANI/Pan NFsM could easily extract eight target analytes in 10 mL of water sample without any pre-treatment, and the analytes retained on NFsM could be easily eluted by 500 μL of 1% acetic acid methanol for direct UPLC-MS/MS analysis. In addition, each piece of PANI/Pan NFsM could be reused for at least 20 times without performance decline. Possible adsorption mechanisms were also proposed. Practical feasibility was validated through the actual sample analysis.

The Systematic Adsorption of Diclofenac onto Waste Red Bricks Functionalized with Iron Oxides

In this study, waste red bricks were incorporated with iron oxides (goethite and hematite) and used for the removal of diclofenac (DCF) from aqueous solutions. The prepared waste red bricks were systematically characterized by XRF, XRD, BET, and SEM. The batch experiments were systematically conducted by investigating the adsorption kinetics, isotherms, thermodynamics, pH, and ionic strength effect. Results showed that the incorporation of iron oxides could enhance the adsorption capacity of DCF onto waste bricks, while the increased effect of hematite was better than goethite. DCF was adsorbed rapidly onto waste bricks, and the adsorption kinetic fitted the pseudo-second-order model perfectly, which could be attributed to the strong interaction between DCF and iron oxides. The increasing pH values decreased the adsorption capacity greatly, which may be due to the electrostatic repulsive interactions. The adsorption of DCF onto waste bricks was an exothermic reaction, and the adsorption isotherms fitted well with the Langmuir model. This study offers new guidelines for the utilization of construction waste, and shows useful methods for the elimination of micropollutants from aqueous solution.

Removal of priority and emerging pollutants from aqueous media by adsorption onto synthetic organo-funtionalized high-charge swelling micas

In this work, the removal of different types of emerging pollutants (four perfluoroalkyl compounds, two preservatives, three surfactants and nine pharmaceutical compounds) from aqueous solution by adsorption onto two novel synthetic clays, a high-charge swelling mica (Na-Mica-4) and an organo-functionalized mica (C₁₈-Mica-4), was evaluated. Na-Mica-4 and C₁₈-Mica- 4 were prepared and characterized by X-Ray diffraction, Zeta potential, specific surface area, thermogravimetric analysis and transmission electron microscopy, before and after adsorption experiments. The influence of the aqueous sample pH, salt addition and extraction time in the removal were evaluated. The results showed the high adsorption affinity of C₁₈-Mica-4 for most of the emerging pollutants analysed after a removal time of 24 h (14 out of 18 pollutants were effectively removed [70-100%]). A high correlation was observed between the log K_ow of the selected emerging pollutants and the adsorption onto C₁₈-Mica-4. The results also indicate that adsorption occurs in the interlayer space. While the removal rates with Na-Mica-4 were in the range 8-97% after seven days, some of the compounds, perfluorobutanoic acid and most of pharmaceutically active compounds, were not adsorbed onto the high-charge mica. C₁₈-Mica- 4 was effectively used for the removal of contaminants from four types of water samples.

Removal of emerging contaminants from the environment by adsorption

Emerging contaminants (EC's) are pollutants of growing concern. They are mainly organic compounds such as: pesticides, pharmaceuticals and personal care products, hormones, plasticizers, food additives, wood preservatives, laundry detergents, surfactants, disinfectants, flame retardants, and other organic compounds that were found recently in natural wastewater stream generated by human and industrial activities. A majority of ECs does not have standard regulations and could lead to lethal effects on human and aquatic life even at small concentrations. The conventional primary and secondary water treatment plants do not remove or degrade these toxic pollutants efficiently and hence need cost effective tertiary treatment method. Adsorption is a promising method worldwide for EC removal since it is low initial cost for implementation, highly-efficient and has simple operating design. Research has shown that the application of different adsorbents such as, activated carbons(ACs), modified biochars (BCs), nanoadsorbents (carbon nanotubes and graphene), composite adsorbents, and other are being used for EC's removal from water and wastewater. The current review intends to investigate adsorption process as an efficient method for the treatment of ECs. The mechanism of adsorption has also been discussed.

Removal of emerging pharmaceutical contaminants by adsorption in a fixed-bed column: A review

Pharmaceutical pollutants substantially affect the environment; thus, their treatments have been the focus of many studies. In this article, the fixed-bed adsorption of pharmaceuticals on various adsorbents was reviewed. The experimental breakthrough curves of these pollutants under various flow rates, inlet concentrations, and bed heights were examined. Fixed-bed data in terms of saturation uptakes, breakthrough time, and the length of the mass transfer zone were included. The three most popular breakthrough models, namely, Adams-Bohart, Thomas, and Yoon-Nelson, were also reviewed for the correlation of breakthrough curve data along with the evaluation of model parameters. Compared with the Adams-Bohart model, the Thomas and Yoon-Nelson more effectively predicted the breakthrough data for the studied pollutants.

Novel synthetic clays for the adsorption of surfactants from aqueous media

The aim of this work was to assess for the first time the use of two high-charge swelling micas (Na-Mica-4 and C₁₈-Mica-4) for the removal of four linear alkylbenzene sulfonates (LAS) from aqueous samples. To this end, Na-Mica-4 was synthesized and organically functionalized with cations of octadecylamine to obtain C₁₈-Mica-4. Na-Mica-4 and C₁₈-Mica-4 were characterized by X-Ray diffraction, Zeta potential, specific surface area and thermogravimetric analysis before and after the adsorption experiments. LAS removal studies were carried out in water samples spiked with a LAS mixture (10 mg L^-1). Removal rates with C₁₈-Mica-4 were between 94% and 97% at pH = 2, and between 98% and 99% at pH = 5 after 1 h. For the same amount of Na-Mica-4, removal rates were between 54% and 81% at pH = 2, and between 24% and 66% at pH = 5 after seven days. No significant effects on the removal rates of C₁₈-Mica-4 were observed for pH values between 0.5 and 9. The experimental equilibrium data were fitted to 30 min, with removal rates of up to 98% in all the experiments. C₁₈-Mica-4 characterization tests indicate that LAS adsorption occurs in the interlayer space. Finally, C₁₈-Mica-4 was applied successfully to the removal of the target compounds from influent and effluent wastewater, surface water and tap water samples.

Surfactant modified zeolite as amphiphilic and dual-electronic adsorbent for removal of cationic and oxyanionic metal ions and organic compounds

A hydrophilic Y zeolite was primarily treated with sodium hydroxide to enhance its cation exchange capacity (Na-zeolite). The organo-zeolite (Na-H-zeolite) was prepared by a modification process of the external surface of Na-zeolite with a cationic surfactant (hexadecyltrimethylammonium; HDTMA). Three adsorbents (i.e., pristine zeolite, Na-zeolite, and Na-H-zeolite) were characterized with nitrogen adsorption/desorption isotherms, scanning electron microscopy coupled with energy dispersive X-ray spectroscopy, cation exchange capacities, and zeta potential. Results demonstrated that HDTMA can be adsorbed on the surface of Na-zeolite to form patchy bilayers. The adsorption capacity of several hazardous pollutants (i.e., Pb²⁺, Cu²⁺, Ni²⁺, Cr₂O₇^2-, propylbenzene, ethylbenzene, toluene, benzene, and phenol) onto Na-H-zeolite was investigated in a single system and multiple-components. Adsorption isotherm was measured to further understand the effects of the modification process on the adsorption behaviors of Na-H-zeolite. Adsorption performances indicated that Na-H-zeolite can simultaneously adsorb the metal cations (on the surface not covered by HDTMA), oxyanions (on the surface covered by HDTMA). Na-H-zeolite also exhibited both hydrophilic and hydrophobic surfaces to uptake organic compounds with various water solubilities (from 55 to 75,000mg/L). It was experimentally concluded that Na-H-zeolite is a potential dual-electronic and amphiphilic adsorbent for efficiently removing a wide range of potentially toxic pollutants from aquatic environments.

One-Step Fabrication of Fe(OH)3@Cellulose Hollow Nanofibers with Superior Capability for Water Purification

The conventional strategies employed for the synthesis of hollow nanofibers (HNFs) require either multistep treatments or special design of the equipment. An additional annealing process is always required, which inevitably consumes more energy and raises the manufacturing cost. In addition, the annealing process may also cause a waste of the matrix materials and the release of toxic gases. Herein, we report for the first time a novel one-step synthesis of hollow hybrid nanofibers via electrospinning. Cellulose was chosen as the polymer matrix, and Fe(OH)₃ nanoparticles were grown in situ on the nanofibers during electrospinning. There was no need to remove cellulose to create the hollow nanofiber structure. This can significantly simplify the fabrication process without any negative influence to the air. The obtained Fe(OH)₃@cellulose HNF membranes exhibited great mechanical properties and an extremely high water flux of 11 200 L m^-2 h^-1 bar^-1. They could effectively remove various pollutants in water, including phosphate, heavy metal ions, and organic dyes, with excellent reusability. Importantly, this approach could also be applied for the fabrication of other hybrid HNFs, which may serve in a broad range of scientific and engineering applications, including water purification, energy conversion and storage, catalysts, sensors, and so on.