The rapid prototyping of anatomic models in pulmonary atresia

Clinical situations for which 3D printing is considered an appropriate representation or extension of data contained in a medical imaging examination: pediatric congenital heart disease conditions

BACKGROUND

The use of medical 3D printing (focusing on anatomical modeling) has continued to grow since the Radiological Society of North America's (RSNA) 3D Printing Special Interest Group (3DPSIG) released its initial guideline and appropriateness rating document in 2018. The 3DPSIG formed a focused writing group to provide updated appropriateness ratings for 3D printing anatomical models across a variety of congenital heart disease. Evidence-based- (where available) and expert-consensus-driven appropriateness ratings are provided for twenty-eight congenital heart lesion categories.

METHODS

A structured literature search was conducted to identify all relevant articles using 3D printing technology associated with pediatric congenital heart disease indications. Each study was vetted by the authors and strength of evidence was assessed according to published appropriateness ratings.

RESULTS

Evidence-based recommendations for when 3D printing is appropriate are provided for pediatric congenital heart lesions. Recommendations are provided in accordance with strength of evidence of publications corresponding to each cardiac clinical scenario combined with expert opinion from members of the 3DPSIG.

CONCLUSIONS

This consensus appropriateness ratings document, created by the members of the RSNA 3DPSIG, provides a reference for clinical standards of 3D printing for pediatric congenital heart disease clinical scenarios.

Perfusion Window Chambers Enable Interventional Analyses of Tumor Microenvironments

Intravital microscopy (IVM) allows spatial and temporal imaging of different cell types in intact live tissue microenvironments. IVM has played a critical role in understanding cancer biology, invasion, metastases, and drug development. One considerable impediment to the field is the inability to interrogate the tumor microenvironment and its communication cascades during disease progression and therapeutic interventions. Here, a new implantable perfusion window chamber (PWC) is described that allows high-fidelity in vivo microscopy, local administration of stains and drugs, and longitudinal sampling of tumor interstitial fluid. This study shows that the new PWC design allows cyclic multiplexed imaging in vivo, imaging of drug action, and sampling of tumor-shed materials. The PWC will be broadly useful as a novel perturbable in vivo system for deciphering biology in complex microenvironments.

3D Virtual modelling, 3D printing and extended reality for planning of implant procedure of short-term and long-term mechanical circulatory support devices and heart transplantation

Introduction

The use of three-dimensional (3D) reconstruction and printing technology, together with extended reality applied to advanced heart failure adult patients with complex anatomy, is rapidly spreading in clinical practice. We report practical experience with application to acute and chronic heart failure: planning and performing mechanical circulatory device insertion or heart transplantation.

Methods

From November 2019 until February 2022, 53 3D virtual biomodels were produced for intervention planning (using Virtual/Augmented Reality and/or 3D printing), following a specific segmentation and preprocessing workflow for biomodelling, in patients with advanced heart failure due to structural heart disease or cardiomyopathies. Four of those patients were complex cases requiring mechanical circulatory support implant procedures in our center.

Results

One short-term and three long-term ventricular assist device system were successfully clinically implanted after application of this technique. In other two cases with extremely high procedural risk, visualized after application of this multimodality imaging, heart transplantation was elected.

Conclusion

3D printing based planning and virtual procedure simulation, are of great importance to select appropriate candidates for mechanical circulatory support in case of complex patient anatomy and may help to diminish periprocedural complications. Extended reality represents a perspective tool in planification of complex surgical procedures or ventricular assist device insertion in this setting.

Benefit of stereoscopic volume rendering for the identification of pediatric pulmonary vein stenosis from CT angiography

The use of three-dimensional (3D) technologies in medical practice is increasing; however, its use is largely untested. One 3D technology, stereoscopic volume-rendered 3D display, can improve depth perception. Pulmonary vein stenosis (PVS) is a rare cardiovascular pathology, often diagnosed by computed tomography (CT), where volume rendering may be useful. Depth cues may be lost when volume rendered CT is displayed on regular screens instead of 3D displays. The objective of this study was to determine whether the 3D stereoscopic display of volume-rendered CT improved perception compared to standard monoscopic display, as measured by PVS diagnosis. CT angiograms (CTAs) from 18 pediatric patients aged 3 weeks to 2 years were volume rendered and displayed with and without stereoscopic display. Patients had 0 to 4 pulmonary vein stenoses. Participants viewed the CTAs in 2 groups with half on monoscopic and half on stereoscopic display and the converse a minimum of 2 weeks later, and their diagnoses were recorded. A total of 24 study participants, comprised of experienced staff cardiologists, cardiovascular surgeons and radiologists, and their trainees viewed the CTAs and assessed the presence and location of PVS. Cases were classified as simple (2 or fewer lesions) or complex (3 or more lesions). Overall, there were fewer type 2 errors in diagnosis for stereoscopic display than standard display, an insignificant difference (p = 0.095). There was a significant decrease in type 2 errors for complex multiple lesion cases (≥3) vs simpler cases (p = 0.027) and improvement in localization of pulmonary veins (p = 0.011). Subjectively, 70% of participants stated that stereoscopy was helpful in the identification of PVS. The stereoscopic display did not result in significantly decreased errors in PVS diagnosis but was helpful for more complex cases.

Standardizing evaluation of patient-specific 3D printed models in surgical planning: development of a cross-disciplinary survey tool for physician and trainee feedback

BACKGROUND

3D printed models are becoming increasingly popular in healthcare as visual and tactile tools to enhance understanding of anatomy and pathology in medical trainee education, provide procedural simulation training, and guide surgical procedures. Patient-specific 3D models are currently being used preoperatively for trainee medical education in planning surgical approaches and intraoperatively to guide decision-making in several specialties. Our study group utilized a modified Delphi process to create a standardized assessment for trainees using patient-specific 3D models as a tool in medical education during pre-surgical planning.

METHODS

A literature review was conducted to identify survey questions administered to clinicians in published surgical planning studies regarding the use of patient-specific 3D models. A core study team reviewed these questions, removed duplicates, categorized them, mapped them to overarching themes, and, where applicable, modified individual questions into a form generalizable across surgical specialties. The core study panel included a physician, physician-scientist, social scientist, engineer/medical student, and 3D printing lab manager. A modified Delphi process was then used to solicit feedback on the clarity and relevance of the individual questions from an expert panel consisting of 12 physicians from specialties including anesthesiology, emergency medicine, radiology, urology, otolaryngology, and obstetrics/gynecology. When the Radiological Society of North America (RSNA)/American College of Radiology (ACR) 3D Printing Registry Data Dictionary was released, additional survey questions were reviewed. A final cross-disciplinary survey of the utility of 3D printed models in surgical planning medical education was developed.

RESULTS

The literature review identified 100 questions previously published in surveys assessing patient-specific 3D models for surgical planning. Following the review, generalization, and mapping of survey questions from these studies, a list of 24 questions was generated for review by the expert study team. Five additional questions were identified in the RSNA/ACR 3D Printing Registry Data Dictionary and included for review. A final questionnaire consisting of 20 questions was developed.

CONCLUSIONS

As 3D printed models become more common in medical education, the need for standardized assessment is increasingly essential. The standardized questionnaire developed in this study reflects the interests of a variety of stakeholders in patient-specific 3D models across disciplines.

Imaging-Based, Patient-Specific Three-Dimensional Printing to Plan, Train, and Guide Cardiovascular Interventions: A Systematic Review and Meta-Analysis

BACKGROUND

To tailor cardiovascular interventions, the use of three-dimensional (3D), patient-specific phantoms (3DPSP) encompasses patient education, training, simulation, procedure planning, and outcome-prediction.

AIM

This systematic review and meta-analysis aims to investigate the current and future perspective of 3D printing for cardiovascular interventions.

METHODS

We systematically screened articles on Medline and EMBASE reporting the prospective use of 3DPSP in cardiovascular interventions by using combined search terms. Studies that compared intervention time depending on 3DPSP utilisation were included into a meta-analysis.

RESULTS

We identified 107 studies that prospectively investigated a total of 814 3DPSP in cardiovascular interventions. Most common settings were congenital heart disease (CHD) (38 articles, 6 comparative studies), left atrial appendage (LAA) occlusion (11 articles, 5 comparative, 1 randomised controlled trial [RCT]), and aortic disease (10 articles). All authors described 3DPSP as helpful in assessing complex anatomic conditions, whereas poor tissue mimicry and the non-consideration of physiological properties were cited as limitations. Compared to controls, meta-analysis of six studies showed a significant reduction of intervention time in LAA occlusion (n=3 studies), and surgery due to CHD (n=3) if 3DPSPs were used (Cohen's d=0.54; 95% confidence interval, 0.13 to 0.95; p=0.001), however heterogeneity across studies should be taken into account.

CONCLUSIONS

3DPSP are helpful to plan, train, and guide interventions in patients with complex cardiovascular anatomy. Benefits for patients include reduced intervention time with the potential for lower radiation exposure and shorter mechanical ventilation times. More evidence and RCTs including clinical endpoints are needed to warrant adoption of 3DPSP into routine clinical practice.

An early health technology assessment of 3D anatomic models in pediatric congenital heart surgery: potential cost-effectiveness and decision uncertainty

Background: Three-dimensional anatomic models have been used for surgical planning and simulation in pediatric congenital heart surgery. This research is the first to evaluate the potential cost-effectiveness of 3D anatomic models with the intent to guide surgeons and decision makers on its use.Method: A decision tree and subsequent Markov model with a 15-year time horizon was constructed and analyzed for nine cardiovascular surgeries. Epidemiological, clinical, and economic data were derived from databases. Literature and experts were consulted to close data gaps. Scenario, one-way, threshold, and probabilistic sensitivity analysis captured methodological and parameter uncertainty.Results: Incremental costs of using anatomical models ranged from -366€ (95% credibility interval: -2595€; 1049€) in the Norwood operation to 1485€ (95% CI: 1206€; 1792€) in atrial septal defect repair. Incremental health-benefits ranged from negligible in atrial septal defect repair to 0.54 Quality Adjusted Life Years (95% CI: 0.06; 1.43) in truncus arteriosus repair. Variability in the results was mainly caused by a temporary postoperative quality-adjusted life years gain.Conclusion: For complex operations, the implementation of anatomic models is likely to be cost-effective on a 15 year time horizon. For the right indication, these models thus provide a clinical advantage at an acceptable cost.

Three-dimensional printing in medicine: a systematic review of pediatric applications

BACKGROUND

Three-dimensional printing (3DP) addresses distinct clinical challenges in pediatric care including: congenital variants, compact anatomy, high procedural risk, and growth over time. We hypothesized that patient-specific applications of 3DP in pediatrics could be categorized into concise, discrete categories of use.

METHODS

Terms related to "three-dimensional printing" and "pediatrics" were searched on PubMed, Scopus, Ovid MEDLINE, Cochrane CENTRAL, and Web of Science. Initial search yielded 2122 unique articles; 139 articles characterizing 508 patients met full inclusion criteria.

RESULTS

Four categories of patient-specific 3DP applications were identified: Teaching of families and medical staff (9.3%); Developing intervention strategies (33.9%); Procedural applications, including subtypes: contour models, guides, splints, and implants (43.0%); and Material manufacturing of shaping devices or prosthetics (14.0%). Procedural comparative studies found 3DP devices to be equivalent or better than conventional methods, with less operating time and fewer complications.

CONCLUSION

Patient-specific applications of Three-Dimensional Printing in Medicine can be elegantly classified into four major categories: Teaching, Developing, Procedures, and Materials, sharing the same TDPM acronym. Understanding this schema is important because it promotes further innovation and increased implementation of these devices to improve pediatric care.

IMPACT

This article classifies the pediatric applications of patient-specific three-dimensional printing. This is a first comprehensive review of patient-specific three-dimensional printing in both pediatric medical and surgical disciplines, incorporating previously described classification schema to create one unifying paradigm. Understanding these applications is important since three-dimensional printing addresses challenges that are uniquely pediatric including compact anatomy, unique congenital variants, greater procedural risk, and growth over time. We identified four classifications of patient-specific use: teaching, developing, procedural, and material uses. By classifying these applications, this review promotes understanding and incorporation of this expanding technology to improve the pediatric care.

Three-dimensional printing in a patient with pulmonary artery pseudoaneurysm and complex congenital heart disease-A case report

3D-printing is a powerful tool in patients with complex anatomy undergoing cardiac surgery.

Three-Dimensional Printing, Virtual Reality and Mixed Reality for Pulmonary Atresia: Early Surgical Outcomes Evaluation

BACKGROUND

Single-stage unifocalisation for pulmonary atresia (PA) with ventricular septal defect (VSD) and major aortopulmonary collateral arteries (MAPCA) requires a high degree of three-dimensional (3D) anatomical imagination. A previous study has reported the application of a 3D-printed heart model with virtual reality (VR) or mixed reality (MR). However, few studies have evaluated the surgical outcomes of the 3D model with VR or MR in PA/VSD patients.

METHODS

Three-dimensional (3D) heart models of five selected PA/VSD patients were derived from traditional imageology of their hearts. Using VR glasses, the 3D models were also visualised in the operating room. Both the 3D-printed heart models and preoperative evaluation by VR were used in the five selected patients for surgical simulation and better anatomical understanding. Mixed reality holograms were used as perioperative assistive tools. Surgical outcomes were assessed, including in-hospital and early follow-up clinical data.

RESULTS

The use of these three new technologies had favourable feedback from the surgeons on intraoperative judgment. There were no in-hospital or early deaths. No reintervention was required until the last follow-up. Three (3) patients developed postoperative complications: one had right bundle branch block and ST-segment change, one had chest drainage >7 days (>40 mL/day) and one had pneumonia.

CONCLUSION

The preoperative application of a 3D-printed heart model with VR or MR helped in aligning the surgical field. These technologies improved the understanding of complicated cardiac anatomy and achieved acceptable surgical outcomes as guiding surgical planning.

3D printing tissue-mimicking materials for realistic transseptal puncture models

Applications of additive manufacturing (commonly referred to as 3D printing) in direct fabrication of models for pre-surgical planning, functional testing, and medical training are on the rise. However, one current limitation to the accuracy of models for cardiovascular procedural training is a lack of printable materials that accurately mimic human tissue. Most of the available elastomeric materials lack mechanical properties representative of human tissues. To address the gap, the authors explore the multi-material capability of material jetting additive manufacturing to combine non-curing and photo-curing inks to achieve material properties that more closely replicate human tissues. The authors explore the impact of relative material concentration on tissue-relevant properties from puncture and tensile testing under submerged conditions. Further, the authors demonstrate the ability to mimic the mechanical properties of the fossa ovalis, which proves beneficial for accurately simulating transseptal punctures. A fossa ovalis mimic was printed and assembled within a full patient-specific heart model for validation, where it exhibited accuracy in both mechanical properties and geometry. The explored material combination provides the opportunity to fabricate future medical models that are more realistic and better suited for pre-surgical planning and medical student training. This will ultimately guide safer, more efficient practices.

Medical three-dimensional printing opens up new opportunities in cardiology and cardiac surgery

Advanced percutaneous and surgical procedures in structural and congenital heart disease require precise pre-procedural planning and continuous quality control. Although current imaging modalities and post-processing software assists with peri-procedural guidance, their capabilities for spatial conceptualization remain limited in two- and three-dimensional representations. In contrast, 3D printing offers not only improved visualization for procedural planning, but provides substantial information on the accuracy of surgical reconstruction and device implantations. Peri-procedural 3D printing has the potential to set standards of quality assurance and individualized healthcare in cardiovascular medicine and surgery. Nowadays, a variety of clinical applications are available showing how accurate 3D computer reformatting and physical 3D printouts of native anatomy, embedded pathology, and implants are and how they may assist in the development of innovative therapies. Accurate imaging of pathology including target region for intervention, its anatomic features and spatial relation to the surrounding structures is critical for selecting optimal approach and evaluation of procedural results. This review describes clinical applications of 3D printing, outlines current limitations, and highlights future implications for quality control, advanced medical education and training.

Dimensional Accuracy and Clinical Value of 3D Printed Models in Congenital Heart Disease: A Systematic Review and Meta-Analysis

The aim of this paper is to summarize and evaluate results from existing studies on accuracy and clinical value of three-dimensional printed heart models (3DPHM) for determining whether 3D printing can significantly improve on how the congenital heart disease (CHD) is managed in current clinical practice. Proquest, Google Scholar, Scopus, PubMed, and Medline were searched for relevant studies until April 2019. Two independent reviewers performed manual data extraction and assessed the risk of bias of the studies using the tools published on National Institutes of Health (NIH) website. The following data were extracted from the studies: author, year of publication, study design, imaging modality, segmentation software, utility of 3DPHM, CHD types, and dimensional accuracy. R software was used for the meta-analysis. Twenty-four articles met the inclusion criteria and were included in the systematic review. However, only 7 studies met the statistical requirements and were eligible for meta-analysis. Cochran's Q test demonstrated significant variation among the studies for both of the meta-analyses of accuracy of 3DPHM and the utility of 3DPHM in medical education. Analysis of all included studies reported the mean deviation between the 3DPHM and the medical images is not significant, implying that 3DPHM are highly accurate. As for the utility of the 3DPHM, it is reported in all relevant studies that the 3DPHM improve the learning experience and satisfaction among the users, and play a critical role in facilitating surgical planning of complex CHD cases. 3DPHM have the potential to enhance communication in medical practice, however their clinical value remains debatable. More studies are required to yield a more meaningful meta-analysis.

Three-dimensional printed surgical templates for fresh cadaveric osteochondral allograft surgery with dimension verification by multivariate computed tomography analysis

BACKGROUND

The fit of the allograft is a particular concern in fresh cadaveric osteochondral allograft (FOCA) surgery. Digital design and fabrication were utilized in conjunction with traditional surgery to enable efficient discovery and reproduction of appropriately dimensioned allograft.

METHODS

A patient with large osteochondral defects in the lateral femoral condyle was to undergo FOCA surgery. A digital virtual operation was performed, based on computed tomography (CT) images of the patient. Polyamide saw templates were manufactured using a selective laser sintering process, and gypsum powder was used to manufacture preoperative and intraoperative medical models with binder jetting process. The design dimensions were verified numerically by determining the intactness of the section surface and allograft volume based on four independent measurements of the initial design, and an automated design optimization strategy was postulated. For the surgery, a lateral longitudinal approach was employed.

RESULTS

The virtual operation allowed an efficient design of the saw templates. Their shape and dimensions were verified with a numerical CT analysis method. The allograft dimensions (medial-lateral/superior-inferior/anterior-posterior) were approximately 40/28.5/24 mm, respectively, with the anterosuperior corner diagonally removed, yielding a section volume of approximately 16.5 cm³. These manually chosen dimensions were reminiscent of the corresponding computationally optimized values.

CONCLUSIONS

Use of computer-aided design in virtual operation planning and three-dimensional printing in the fabrication of designed templates allowed for an efficient FOCA procedure and accurate allograft fitting. The numerical optimization method allowed for a semiautomated design process, which could in turn be realized also with surgical navigation or robotic surgery methods.

Living the heart in three dimensions: applications of 3D printing in CHD

Advances in biomedical engineering have led to three-dimensional (3D)-printed models being used for a broad range of different applications. Teaching medical personnel, communicating with patients and relatives, planning complex heart surgery, or designing new techniques for repair of CHD via cardiac catheterisation are now options available using patient-specific 3D-printed models. The management of CHD can be challenging owing to the wide spectrum of morphological conditions and the differences between patients. Direct visualisation and manipulation of the patients' individual anatomy has opened new horizons in personalised treatment, providing the possibility of performing the whole procedure in vitro beforehand, thus anticipating complications and possible outcomes. In this review, we discuss the workflow to implement 3D printing in clinical practice, the imaging modalities used for anatomical segmentation, the applications of this emerging technique in patients with structural heart disease, and its limitations and future directions.

Personalized Three-Dimensional Printed Models in Congenital Heart Disease

Patient-specific three-dimensional (3D) printed models have been increasingly used in cardiology and cardiac surgery, in particular, showing great value in the domain of congenital heart disease (CHD). CHD is characterized by complex cardiac anomalies with disease variations between individuals; thus, it is difficult to obtain comprehensive spatial conceptualization of the cardiac structures based on the current imaging visualizations. 3D printed models derived from patient's cardiac imaging data overcome this limitation by creating personalized 3D heart models, which not only improve spatial visualization, but also assist preoperative planning and simulation of cardiac procedures, serve as a useful tool in medical education and training, and improve doctor-patient communication. This review article provides an overall view of the clinical applications and usefulness of 3D printed models in CHD. Current limitations and future research directions of 3D printed heart models are highlighted.

3D-Printed Models for Surgical Planning in Complex Congenital Heart Diseases: A Systematic Review

Background: 3D technology support is an emerging technology in the field of congenital heart diseases (CHD). The goals of 3D printings or models is mainly a better analysis of complex anatomies to optimize the surgical repair or intervention planning. Method: We performed a systematic review to evaluate the accuracy and reliability of CHD modelization and 3D printing, as well as the proof of concept of the benefit of 3D printing in planning interventions. Results: Correlation studies showed good results with anatomical measurements. This technique can therefore be considered reliable with the limit of the operator's subjectivity in modelizing the defect. In cases series, the benefits of the 3D technology have been shown for describing the vessels anatomy and guiding the surgical approach. For intra-cardiac complex anatomy, 3D models have been shown helpful for the planification of intracardiac repair. However, there is still lack of evidence based approach for the usefulness of 3D models in CHD in changing outcomes after surgery or interventional procedures due to the difficulty to design a prospective study with comprehensive and clinically meaningful end-points. Conclusion: 3D technology can be used to improve the understanding of anatomy of complex CHD and to guide surgical strategy. However, there is a need to design clinical studies to identify the place of this approach in the current clinical practice.

Additive manufacturing applications in cardiology: A review

BACKGROUND

Additive manufacturing (AM) has emerged as a serious planning, strategy, and education tool in cardiovascular medicine. This review describes and illustrates the application, development and associated limitation of additive manufacturing in the field of cardiology by studying research papers on AM in medicine/cardiology.

METHODS

Relevant research papers till August 2018 were identified through Scopus and examined for strength, benefits, limitation, contribution and future potential of AM. With the help of the existing literature & bibliometric analysis, different applications of AM in cardiology are investigated.

RESULTS

AM creates an accurate three-dimensional anatomical model to explain, understand and prepare for complex medical procedures. A prior study of patient's 3D heart model can help doctors understand the anatomy of the individual patient, which may also be used create training modules for institutions and surgeons for medical training.

CONCLUSION

AM has the potential to be of immense help to the cardiologists and cardiac surgeons for intervention and surgical planning, monitoring and analysis. Additive manufacturing creates a 3D model of the heart of a specific patient in lesser time and cost. This technology is used to create and analyse 3D model before starting actual surgery on the patient. It can improve the treatment outcomes for patients, besides saving their lives. Paper summarised additive manufacturing applications particularly in the area of cardiology, especially manufacturing of a patient-specific artificial heart or its component. Model printed by this technology reduces risk, improves the quality of diagnosis and preoperative planning and also enhanced team communication. In cardiology, patient data of heart varies from patient to patient, so AM technologies efficiently produce 3D models, through converting the predesigned virtual model into a tangible object. Companies explore additive manufacturing for commercial medical applications.

Radiological Society of North America (RSNA) 3D printing Special Interest Group (SIG): guidelines for medical 3D printing and appropriateness for clinical scenarios

Medical three-dimensional (3D) printing has expanded dramatically over the past three decades with growth in both facility adoption and the variety of medical applications. Consideration for each step required to create accurate 3D printed models from medical imaging data impacts patient care and management. In this paper, a writing group representing the Radiological Society of North America Special Interest Group on 3D Printing (SIG) provides recommendations that have been vetted and voted on by the SIG active membership. This body of work includes appropriate clinical use of anatomic models 3D printed for diagnostic use in the care of patients with specific medical conditions. The recommendations provide guidance for approaches and tools in medical 3D printing, from image acquisition, segmentation of the desired anatomy intended for 3D printing, creation of a 3D-printable model, and post-processing of 3D printed anatomic models for patient care.

3D printing for preoperative planning and surgical training: a review

Surgeons typically rely on their past training and experiences as well as visual aids from medical imaging techniques such as magnetic resonance imaging (MRI) or computed tomography (CT) for the planning of surgical processes. Often, due to the anatomical complexity of the surgery site, two dimensional or virtual images are not sufficient to successfully convey the structural details. For such scenarios, a 3D printed model of the patient's anatomy enables personalized preoperative planning. This paper reviews critical aspects of 3D printing for preoperative planning and surgical training, starting with an overview of the process-flow and 3D printing techniques, followed by their applications spanning across multiple organ systems in the human body. State of the art in these technologies are described along with a discussion of current limitations and future opportunities.

The Role of Three-Dimensional Printing in Contemporary Vascular and Endovascular Surgery: A Systematic Review

BACKGROUND

Three-dimensional (3D) printing, also known as rapid prototyping or additive manufacturing, is a novel adjunct in the medical field. The aim of this systematic review is to evaluate the role of 3D printing technology in the field of contemporary vascular surgery in terms of its technical aspect, practicability, and clinical outcome.

METHODS

A systematic search of literatures published from January 1, 1980 to July 15, 2017 was identified from the EMBASE, MEDLINE, and Cochrane library database with reference to the Preferred Reporting Items for Systematic Reviews and Meta-Analyses guideline. The predefined selection inclusion criterion was clinical application of 3D printing technology in vascular surgery of large and small vessel pathology.

RESULTS

Forty-two articles were included in this systematic review, including 2 retrospective cohorts and 1 prospective case control study. 3D printing was mostly applied to abdominal aortic aneurysm (n = 20) and thoracic aorta pathology (n = 8), other vessels included celiac, splenic, carotid, subclavian, femoral artery, and portal vein (n = 10). The most commonly quoted materials were acrylonitrile-butadiene-styrene (n = 2), polylactic acid (n = 4), polyurethane resin (n = 3) and nylon (n = 3). The cost per replica ranged from USD $4-2,360. Cost for a commercial printer was around USD $2,210-50,000.

CONCLUSION

3D printing was recognized and gradually incorporated as a useful adjunct in the field of vascular and endovascular surgery. The production of an accurate anatomic patient-specific replica was shown to bring significant impact in patient management in terms of anatomic understanding, procedural planning, and intraoperative navigation, education, and academic research as well as patient communication. Further analysis on cost-effectiveness was indicated to guide decisions on applicability of such promising technology on a routine basis.

Innovative interventional catheterization techniques for congenital heart disease

Since 1929, when the first cardiac catheterization was safely performed in a human by Dr. Werner Forssmann (on himself), there has been a rapid progression of cardiac catheterization techniques and technologies. Today, these advances allow us to treat a wide variety of patients with congenital heart disease using minimally invasive techniques; from fetus to infants to adults, and from simple to complex congenital cardiac lesions. In this article, we will explore some of the exciting advances in cardiac catheterization for the treatment of congenital heart disease, including transcatheter valve implantation, hybrid procedures, biodegradable technologies, and magnetic resonance imaging (MRI)-guided catheterization. Additionally, we will discuss innovations in imaging in the catheterization laboratory, including 3D rotational angiography (3DRA), fusion imaging, and 3D printing, which help to make innovative interventional approaches possible.

3D Printing is a Transformative Technology in Congenital Heart Disease

Survival in congenital heart disease has steadily improved since 1938, when Dr. Robert Gross successfully ligated for the first time a patent ductus arteriosus in a 7-year-old child. To continue the gains made over the past 80 years, transformative changes with broad impact are needed in management of congenital heart disease. Three-dimensional printing is an emerging technology that is fundamentally affecting patient care, research, trainee education, and interactions among medical teams, patients, and caregivers. This paper first reviews key clinical cases where the technology has affected patient care. It then discusses 3-dimensional printing in trainee education. Thereafter, the role of this technology in communication with multidisciplinary teams, patients, and caregivers is described. Finally, the paper reviews translational technologies on the horizon that promise to take this nascent field even further.

Feasibility and Validity of Printing 3D Heart Models from Rotational Angiography

Rotational angiography (RA) has proven to be an excellent method for evaluating congenital disease (CHD) in the cardiac cath lab, permitting acquisition of 3D datasets with superior spatial resolution. This technique has not been routinely implemented for 3D printing in CHD. We describe our case series of models printed from RA and validate our technique. All patients with models printed from RA were selected. RA acquisitions from a Toshiba Infinix-I system were postprocessed and printed with a Stratasys Eden 260. Two independent observers measured 5-10 points of interest on both the RA and the 3D model. Bland Altman plot was used to compare the measurements on rotational angiography to the printed model. Models were printed from RA in 5 patients (age 2 months-1 year). Diagnoses included (a) coronary artery aneurysm, (b) Glenn shunt, (c) coarctation of the aorta, (d) tetralogy of Fallot with MAPCAs, and (e) pulmonary artery stenosis. There was no significant measurement difference between RA and the printed model (r = 0.990, p < 0.01, Bland Altman p = 0.987). There was also no significant inter-observer variability. The MAPCAs model was referenced by the surgeon intraoperatively and was accurate. Rotational angiography can generate highly accurate 3D models in congenital heart disease, including in small vascular structures. These models can be extremely useful in patient evaluation and management.

3D Modelling and Printing Technology to Produce Patient-Specific 3D Models

BACKGROUND

A comprehensive knowledge of mitral valve (MV) anatomy is crucial in the assessment of MV disease. While the use of three-dimensional (3D) modelling and printing in MV assessment has undergone early clinical evaluation, the precision and usefulness of this technology requires further investigation. This study aimed to assess and validate 3D modelling and printing technology to produce patient-specific 3D MV models.

METHODS

A prototype method for MV 3D modelling and printing was developed from computed tomography (CT) scans of a plastinated human heart. Mitral valve models were printed using four 3D printing methods and validated to assess precision. Cardiac CT and 3D echocardiography imaging data of four MV disease patients was used to produce patient-specific 3D printed models, and 40 cardiac health professionals (CHPs) were surveyed on the perceived value and potential uses of 3D models in a clinical setting.

RESULTS

The prototype method demonstrated submillimetre precision for all four 3D printing methods used, and statistical analysis showed a significant difference (p<0.05) in precision between these methods. Patient-specific 3D printed models, particularly using multiple print materials, were considered useful by CHPs for preoperative planning, as well as other applications such as teaching and training.

CONCLUSIONS

This study suggests that, with further advances in 3D modelling and printing technology, patient-specific 3D MV models could serve as a useful clinical tool. The findings also highlight the potential of this technology to be applied in a variety of medical areas within both clinical and educational settings.

3D printing from cardiovascular CT: a practical guide and review

Current cardiovascular imaging techniques allow anatomical relationships and pathological conditions to be captured in three dimensions. Three-dimensional (3D) printing, or rapid prototyping, has also become readily available and made it possible to transform virtual reconstructions into physical 3D models. This technology has been utilised to demonstrate cardiovascular anatomy and disease in clinical, research and educational settings. In particular, 3D models have been generated from cardiovascular computed tomography (CT) imaging data for purposes such as surgical planning and teaching. This review summarises applications, limitations and practical steps required to create a 3D printed model from cardiovascular CT.

Clinical application of three-dimensional printing to the management of complex univentricular hearts with abnormal systemic or pulmonary venous drainage

In recent years, three-dimensional printing has demonstrated reliable reproducibility of several organs including hearts with complex congenital cardiac anomalies. This represents the next step in advanced image processing and can be used to plan surgical repair. In this study, we describe three children with complex univentricular hearts and abnormal systemic or pulmonary venous drainage, in whom three-dimensional printed models based on CT data assisted with preoperative planning. For two children, after group discussion and examination of the models, a decision was made not to proceed with surgery. We extend the current clinical experience with three-dimensional printed modelling and discuss the benefits of such models in the setting of managing complex surgical problems in children with univentricular circulation and abnormal systemic or pulmonary venous drainage.

3D Printing and 3D Bioprinting in Pediatrics

Additive manufacturing, commonly referred to as 3D printing, is a technology that builds three-dimensional structures and components layer by layer. Bioprinting is the use of 3D printing technology to fabricate tissue constructs for regenerative medicine from cell-laden bio-inks. 3D printing and bioprinting have huge potential in revolutionizing the field of tissue engineering and regenerative medicine. This paper reviews the application of 3D printing and bioprinting in the field of pediatrics.

Use of 3D models of vascular rings and slings to improve resident education

OBJECTIVE

Three-dimensional (3D) printing is a manufacturing method by which an object is created in an additive process, and can be used with medical imaging data to generate accurate physical reproductions of organs and tissues for a variety of applications. We hypothesized that using 3D printed models of congenital cardiovascular lesions to supplement an educational lecture would improve learners' scores on a board-style examination.

DESIGN AND INTERVENTION

Patients with normal and abnormal aortic arches were selected and anonymized to generate 3D printed models. A cohort of pediatric and combined pediatric/emergency medicine residents were then randomized to intervention and control groups. Each participant was given a subjective survey and an objective board-style pretest. Each group received the same 20-minutes lecture on vascular rings and slings. During the intervention group's lecture, 3D printed physical models of each lesion were distributed for inspection. After each lecture, both groups completed the same subjective survey and objective board-style test to assess their comfort with and postlecture knowledge of vascular rings.

RESULTS

There were no differences in the basic demographics of the two groups. After the lectures, both groups' subjective comfort levels increased. Both groups' scores on the objective test improved, but the intervention group scored higher on the posttest.

CONCLUSIONS

This study demonstrated a measurable gain in knowledge about vascular rings and pulmonary artery slings with the addition of 3D printed models of the defects. Future applications of this teaching modality could extend to other congenital cardiac lesions and different learners.

Precise treatment of aortic aneurysm by three-dimensional printing and simulation before endovascular intervention

In this study, three-dimensional printing (3Dp) models and simulation surgeries (SSs) were applied in two challenging aortic cases. The first was an abdominal aortic aneurysm with a complex neck, and the second was a thoracic aortic dissection aneurysm (TADA) with an angled arch. In order to avoid unpredictable obstacles and difficulties, we made optimal surgical plans by using 3D models and virtual simulations. Based on preoperative evaluation system, the surgical plans seemed more reasonable and time-saving.

A systematic review of 3-D printing in cardiovascular and cerebrovascular diseases

Objective:

The application of 3-D printing has been increasingly used in medicine, with research showing many applications in cardiovascular disease. This systematic review analyzes those studies published about the applications of 3-D printed, patient-specific models in cardiovascular and cerebrovascular diseases.

Methods:

A search of PubMed/Medline and Scopus databases was performed to identify studies investigating the 3-D printing in cardiovascular and cerebrovascular diseases. Only studies based on patient’s medical images were eligible for review, while reports on in vitro phantom or review articles were excluded.

Results:

A total of 48 studies met selection criteria for inclusion in the review. A range of patient-specific 3-D printed models of different cardiovascular and cerebrovascular diseases were generated in these studies with most of them being developed using cardiac CT and MRI data, less commonly with 3-D invasive angiographic or echocardiographic images. The review of these studies showed high accuracy of 3-D printed, patient-specific models to represent complex anatomy of the cardiovascular and cerebrovascular system and depict various abnormalities, especially congenital heart diseases and valvular pathologies. Further, 3-D printing can serve as a useful education tool for both parents and clinicians, and a valuable tool for pre-surgical planning and simulation.

Conclusion:

This systematic review shows that 3-D printed models based on medical imaging modalities can accurately replicate complex anatomical structures and pathologies of the cardiovascular and cerebrovascular system. 3-D printing is a useful tool for both education and surgical planning in these diseases.

Applications of 3D printing in cardiovascular diseases

3D-printed models fabricated from CT, MRI, or echocardiography data provide the advantage of haptic feedback, direct manipulation, and enhanced understanding of cardiovascular anatomy and underlying pathologies. Reported applications of cardiovascular 3D printing span from diagnostic assistance and optimization of management algorithms in complex cardiovascular diseases, to planning and simulating surgical and interventional procedures. The technology has been used in practically the entire range of structural, valvular, and congenital heart diseases, and the added-value of 3D printing is established. Patient-specific implants and custom-made devices can be designed, produced, and tested, thus opening new horizons in personalized patient care and cardiovascular research. Physicians and trainees can better elucidate anatomical abnormalities with the use of 3D-printed models, and communication with patients is markedly improved. Cardiovascular 3D bioprinting and molecular 3D printing, although currently not translated into clinical practice, hold revolutionary potential. 3D printing is expected to have a broad influence in cardiovascular care, and will prove pivotal for the future generation of cardiovascular imagers and care providers. In this Review, we summarize the cardiovascular 3D printing workflow, from image acquisition to the generation of a hand-held model, and discuss the cardiovascular applications and the current status and future perspectives of cardiovascular 3D printing.

3D-printing techniques in a medical setting: a systematic literature review

BACKGROUND

Three-dimensional (3D) printing has numerous applications and has gained much interest in the medical world. The constantly improving quality of 3D-printing applications has contributed to their increased use on patients. This paper summarizes the literature on surgical 3D-printing applications used on patients, with a focus on reported clinical and economic outcomes.

METHODS

Three major literature databases were screened for case series (more than three cases described in the same study) and trials of surgical applications of 3D printing in humans.

RESULTS

227 surgical papers were analyzed and summarized using an evidence table. The papers described the use of 3D printing for surgical guides, anatomical models, and custom implants. 3D printing is used in multiple surgical domains, such as orthopedics, maxillofacial surgery, cranial surgery, and spinal surgery. In general, the advantages of 3D-printed parts are said to include reduced surgical time, improved medical outcome, and decreased radiation exposure. The costs of printing and additional scans generally increase the overall cost of the procedure.

CONCLUSION

3D printing is well integrated in surgical practice and research. Applications vary from anatomical models mainly intended for surgical planning to surgical guides and implants. Our research suggests that there are several advantages to 3D-printed applications, but that further research is needed to determine whether the increased intervention costs can be balanced with the observable advantages of this new technology. There is a need for a formal cost-effectiveness analysis.

Three-dimensional printed models in congenital heart disease

The purpose of this article is to discuss technical considerations and current applications of three-dimensional (3D) printing in congenital heart disease (CHD). CHD represent an attractive field for the application of 3D printed models, with consistent progress made in the past decade. Current 3D models are able to reproduce complex cardiac and extra-cardiac anatomy including small details with very limited range of errors (<1 mm), so this tool could be of value in the planning of surgical or percutaneous treatments for selected cases of CHD. However, the steps involved in the building of 3D models, consisting of image acquisition and selection, segmentation, and printing are highly operator dependent. Current 3D models may be rigid or flexible, but unable to reproduce the physiologic variations during the cardiac cycle. Furthermore, high costs and long average segmentation and printing times (18-24 h) limit a more extensive use. There is a need for better standardization of the procedure employed for collection of the images, the segmentation methods and processes, the phase of cardiac cycle used, and in the materials employed for printing. More studies are necessary to evaluate the diagnostic accuracy and cost-effectiveness of 3D printed models in congenital cardiac care.

3D printing in medicine of congenital heart diseases

Congenital heart diseases causing significant hemodynamic and functional consequences require surgical repair. Understanding of the precise surgical anatomy is often challenging and can be inadequate or wrong. Modern high resolution imaging techniques and 3D printing technology allow 3D printing of the replicas of the patient’s heart for precise understanding of the complex anatomy, hands-on simulation of surgical and interventional procedures, and morphology teaching of the medical professionals and patients. CT or MR images obtained with ECG-gating and breath-holding or respiration navigation are best suited for 3D printing. 3D echocardiograms are not ideal but can be used for printing limited areas of interest such as cardiac valves and ventricular septum. Although the print materials still require optimization for representation of cardiovascular tissues and valves, the surgeons find the models suitable for practicing closure of the septal defects, application of the baffles within the ventricles, reconstructing the aortic arch, and arterial switch procedure. Hands-on surgical training (HOST) on models may soon become a mandatory component of congenital heart disease surgery program. 3D printing will expand its utilization with further improvement of the use of echocardiographic data and image fusion algorithm across multiple imaging modalities and development of new printing materials. Bioprinting of implants such as stents, patches and artificial valves and tissue engineering of a part of or whole heart using the patient’s own cells will open the door to a new era of personalized medicine.

Three-dimensional Physical Modeling: Applications and Experience at Mayo Clinic

Radiologists will be at the center of the rapid technologic expansion of three-dimensional (3D) printing of medical models, as accurate models depend on well-planned, high-quality imaging studies. This article outlines the available technology and the processes necessary to create 3D models from the radiologist's perspective. We review the published medical literature regarding the use of 3D models in various surgical practices and share our experience in creating a hospital-based three-dimensional printing laboratory to aid in the planning of complex surgeries.

Blood Pool Segmentation Results in Superior Virtual Cardiac Models than Myocardial Segmentation for 3D Printing

The method of cardiac magnetic resonance (CMR) three-dimensional (3D) image acquisition and post-processing which should be used to create optimal virtual models for 3D printing has not been studied systematically. Patients (n = 19) who had undergone CMR including both 3D balanced steady-state free precession (bSSFP) imaging and contrast-enhanced magnetic resonance angiography (MRA) were retrospectively identified. Post-processing for the creation of virtual 3D models involved using both myocardial (MS) and blood pool (BP) segmentation, resulting in four groups: Group 1-bSSFP/MS, Group 2-bSSFP/BP, Group 3-MRA/MS and Group 4-MRA/BP. The models created were assessed by two raters for overall quality (1-poor; 2-good; 3-excellent) and ability to identify predefined vessels (1-5: superior vena cava, inferior vena cava, main pulmonary artery, ascending aorta and at least one pulmonary vein). A total of 76 virtual models were created from 19 patient CMR datasets. The mean overall quality scores for Raters 1/2 were 1.63 ± 0.50/1.26 ± 0.45 for Group 1, 2.12 ± 0.50/2.26 ± 0.73 for Group 2, 1.74 ± 0.56/1.53 ± 0.61 for Group 3 and 2.26 ± 0.65/2.68 ± 0.48 for Group 4. The numbers of identified vessels for Raters 1/2 were 4.11 ± 1.32/4.05 ± 1.31 for Group 1, 4.90 ± 0.46/4.95 ± 0.23 for Group 2, 4.32 ± 1.00/4.47 ± 0.84 for Group 3 and 4.74 ± 0.56/4.63 ± 0.49 for Group 4. Models created using BP segmentation (Groups 2 and 4) received significantly higher ratings than those created using MS for both overall quality and number of vessels visualized (p < 0.05), regardless of the acquisition technique. There were no significant differences between Groups 1 and 3. The ratings for Raters 1 and 2 had good correlation for overall quality (ICC = 0.63) and excellent correlation for the total number of vessels visualized (ICC = 0.77). The intra-rater reliability was good for Rater A (ICC = 0.65). Three models were successfully printed on desktop 3D printers with good quality and accurate representation of the virtual 3D models. We recommend using BP segmentation with either MRA or bSSFP source datasets to create virtual 3D models for 3D printing. Desktop 3D printers can offer good quality printed models with accurate representation of anatomic detail.

Advantages and disadvantages of 3-dimensional printing in surgery: A systematic review

BACKGROUND

Three-dimensional (3D) printing is becoming increasingly important in medicine and especially in surgery. The aim of the present work was to identify the advantages and disadvantages of 3D printing applied in surgery.

METHODS

We conducted a systematic review of articles on 3D printing applications in surgery published between 2005 and 2015 and identified using a PubMed and EMBASE search. Studies dealing with bioprinting, dentistry, and limb prosthesis or those not conducted in a hospital setting were excluded.

RESULTS

A total of 158 studies met the inclusion criteria. Three-dimensional printing was used to produce anatomic models (n = 113, 71.5%), surgical guides and templates (n = 40, 25.3%), implants (n = 15, 9.5%) and molds (n = 10, 6.3%), and primarily in maxillofacial (n = 79, 50.0%) and orthopedic (n = 39, 24.7%) operations. The main advantages reported were the possibilities for preoperative planning (n = 77, 48.7%), the accuracy of the process used (n = 53, 33.5%), and the time saved in the operating room (n = 52, 32.9%); 34 studies (21.5%) stressed that the accuracy was not satisfactory. The time needed to prepare the object (n = 31, 19.6%) and the additional costs (n = 30, 19.0%) were also seen as important limitations for routine use of 3D printing.

CONCLUSION

The additional cost and the time needed to produce devices by current 3D technology still limit its widespread use in hospitals. The development of guidelines to improve the reporting of experience with 3D printing in surgery is highly desirable.

Application of Virtual Three-Dimensional Models for Simultaneous Visualization of Intracardiac Anatomic Relationships in Double Outlet Right Ventricle

Our goal was to construct three-dimensional (3D) virtual models to allow simultaneous visualization of the ventricles, ventricular septal defect (VSD) and great arteries in patients with complex intracardiac anatomy to aid in surgical planning. We also sought to correlate measurements from the source cardiac magnetic resonance (CMR) image dataset and the 3D model. Complicated ventriculo-arterial relationships in patients with complex conotruncal malformations make preoperative assessment of possible repair pathways difficult. Patients were chosen with double outlet right ventricle for the complexity of intracardiac anatomy and potential for better delineation of anatomic spatial relationships. Virtual 3D models were generated from CMR 3D datasets. Measurements were made on the source CMR as well as the 3D model for the following structures: aortic diameter in orthogonal planes, VSD diameter in orthogonal planes and long axis of right ventricle. A total of six patients were identified for inclusion. The path from the ventricles to each respective outflow tract and the location of the VSD with respect to each great vessel was visualized clearly in all patients. Measurements on the virtual model showed excellent correlation with the source CMR when all measurements were included by Pearson coefficient, r = 0.99 as well as for each individual structure. Construction of virtual 3D models in patients with complex conotruncal defects from 3D CMR datasets allows for simultaneous visualization of anatomic relationships relevant for surgical repair. The availability of these models may allow for a more informed preoperative evaluation in these patients.

Applications of three-dimensional printing technology in the cardiovascular field

Three-dimensional (3-D) printing technology has rapidly developed in the last few decades. Meanwhile, the application of this technology has reached beyond the engineering field and expanded to almost all disciplines, including medicine. There has been much research on the medical applications of 3-D printing in neurosurgery, orthopedics, maxillofacial surgery, plastic surgery, tissue engineering, as well as other fields. Because of the complexity of the cardiovascular system, the application of this technology is limited and difficult, as compared to other disciplines, and thus there is much room for future development. Many of the difficulties associated with this technology must be overcome. Nonetheless, there is no doubt that 3-D printing technology will benefit patients with cardiovascular diseases in the near future.

3D-manufactured patient-specific models of congenital heart defects for communication in clinical practice: feasibility and acceptability

OBJECTIVES

To assess the communication potential of three-dimensional (3D) patient-specific models of congenital heart defects and their acceptability in clinical practice for cardiology consultations.

DESIGN

This was a questionnaire-based study in which participants were randomised into two groups: the 'model group' received a 3D model of the cardiac lesion(s) being discussed during their appointment, while the 'control group' had a routine visit.

SETTING

Outpatient clinic, cardiology follow-up visits.

PARTICIPANTS

103 parents of children with congenital heart disease were recruited (parental age: 43±8 years; patient age: 12±6 years). In order to have a 3D model made, patients needed to have a recent cardiac MRI examination; this was the crucial inclusion criterion.

INTERVENTIONS

Questionnaires were administered to the participants before and after the visits and an additional questionnaire was administered to the attending cardiologist.

MAIN OUTCOME MEASURES

Rating (1-10) for the liking of the 3D model, its usefulness and the clarity of the explanation received were recorded, as well as rating (1-10) of the parental understanding and their engagement according to the cardiologist. Furthermore, parental knowledge was assessed by asking them to mark diagrams, tick keywords and provide free text answers. The duration of consultations was recorded and parent feedback collected.

RESULTS

Parents and cardiologists both found the models to be very useful and helpful in engaging the parents in discussing congenital heart defects. Parental knowledge was not associated with their level of education (p=0.2) and did not improve following their visit. Consultations involving 3D models lasted on average 5 min longer (p=0.02).

CONCLUSIONS

Patient-specific models can enhance engagement with parents and improve communication between cardiologists and parents, potentially impacting on parent and patient psychological adjustment following treatment. However, in the short-term, parental understanding of their child's condition did not improve.

Three-dimensional printing in cardiac surgery and interventional cardiology: a single-centre experience

OBJECTIVES

In individual cases, routine preoperative imaging might not be sufficient for optimal planning of cardiovascular procedures. Three-dimensional printing (3D), a widely used technique to build life-like replicas of anatomical structures that has proven value in different medical disciplines, might overcome these shortcomings. However, data on 3D printing in cardiovascular medicine are limited to single reports. This stimulated us to present our single-centre experience with 3D printing models in cardiac surgery and interventional cardiology.

METHODS

Between the years 2006 and 2013, we fabricated 3D printing models using preoperative computed tomography or magnetic resonance imaging data in paediatric and adult cardiac surgery, as well as interventional cardiology. We present the 8 most representative cases.

RESULTS

The models were very helpful for perioperative planning and orientation, as well as simulation of procedures due to the exact and life-like illustration of the cardiovascular anatomy.

CONCLUSIONS

The fabrication of 3D printing models is feasible for perioperative planning and simulation in a variety of complex cases in paediatric and adult cardiac surgery, as well as in interventional cardiology. Further studies including more patients and providing more data are expected to demonstrate that the use of 3D printing may decrease morbidity and mortality of complex, non-routine procedures in cardiovascular medicine.

Three-dimensional printing for perioperative planning of complex aortic arch surgery

PURPOSE

In this study, we show the use of three-dimensional printing models for preoperative planning of surgery for patients with complex aortic arch anomalies.

DESCRIPTION

A 70-year-old man with an extensively arteriosclerotic aneurysm reaching from the ascending aorta to the descending aorta was referred to our center for complete aortic arch replacement. We visualized and reconstructed computed tomography data of the patient and fabricated a flexible three-dimensional model of the aortic arch including the aneurysm.

EVALUATION

This model was very helpful for the preoperative decision making and planning of the frozen elephant trunk procedure owing to the exact and lifelike illustration of the native aortic arch.

CONCLUSIONS

Three-dimensional models are helpful in preoperative planning and postoperative evaluation of frozen elephant trunk procedures in patients with complex aortic anatomy.

Three-dimensional printing model of anomalous bronchi before surgery

Lung surgeries in patients with bronchial variations have rarely been reported. Here, we describe the case of a patient along with lung cancer with variant anatomy of the right upper lobe bronchus. This variation was evaluated by three-dimensional multi-detector computed tomography angiography with bronchography and a three-dimensional printing model using rapid prototyping. The variant anterior segment bronchus (S3) of the right upper lobe arising from the middle lobe bronchus was confirmed before surgery using the printing model, which helped to determine the extent of resection required and facilitated the understanding of the patient's anatomy during surgery. A thoracoscopic anterior segmentectomy and middle lobectomy were performed. The printing model was useful for detecting and evaluating the variant bronchi.