Engineered nanomaterials and their surface functionalization for the removal of heavy metals: A review

Three-Dimensional Porous Artemia Cyst Shell Biochar-Supported Iron Oxide Nanoparticles for Efficient Removal of Chromium from Wastewater

Chromium-containing wastewater poses severe threats to ecosystems and human health due to the high toxicity of hexavalent chromium (Cr(VI)). Although iron oxide nanoparticles (IONPs) show promise for Cr(VI) removal, their practical application is hindered by challenges in recovery and reuse. Herein, a novel three-dimensional porous nanocomposite, Artemia cyst shell biochar-supported iron oxide nanoparticles (ACSC@ IONP), was synthesized via synchronous pyrolysis of Fe3+-impregnated Artemia cyst shells (ACSs) and in situ reduction of iron. The optimized composite C@Fe-3, prepared with 1 mol/L Fe3+ and pyrolyzed at 450 °C for 5 h, exhibited rapid removal equilibrium within 5-10 min for both Cr(VI) and total chromium (Cr(total)), attributed to synergistic reduction of Cr(VI) to Cr(III) and adsorption of Cr(VI) and Cr(III). The maximum Cr(total) adsorption capacity was 110.1 mg/g at pH 2, as determined by the Sips isothermal model for heterogeneous adsorption. Competitive experiments demonstrated robust selectivity for Cr(VI) removal even under a 64-fold excess of competing anions, with an interference order of SO42- > NO3- > Cl-. Remarkably, C@Fe-3 retained 65% Cr(VI) removal efficiency after four adsorption-desorption cycles. This study provides a scalable and eco-friendly strategy for fabricating reusable adsorbents with dual functionality for chromium remediation.

Adsorption of heavy metals from wastewater using reduced graphene oxide@titanate hybrids in batch and fixed bed systems

Wastewater contaminated by heavy metal ions poses serious threats to the ecosystem, needing to be well disposed of. In this study, reduced graphene oxide@titanate hybrids (rGOTHs) are synthesized to efficiently remove heavy metals from wastewater in batch and fixed bed systems. The size of prepared rGOTHs is large as hundreds of microns, which is beneficial for separation and application in batch and fixed bed system. In the batch studies, rGOTHs exhibits the fast adsorption rate and high adsorption capacity towards heavy metals, in which the adsorption kinetic and isothermal are best fitted to Pseudo-second-order kinetic model and Langmuir model, respectively. The maximum adsorption capacities of rGOTHs for Pb(II), Cd(II) and Cu(II) are 530.5, 201 and 130.5 mg/g at 298 K and pH 5, respectively. In addition, the exhausted adsorbent can be easily regenerated in alkaline hydrothermal process and the high removal efficiency is almost reserved after six cycles. Moreover, rGOTHs presents higher selective adsorption towards Pb(II) than other ions. Adsorption mechanisms are revealed to be ions exchange, electrostatic interaction, and coordination. In the fixed bed experiments, the effective treatment volume of rGOTHs-loaded column reaches to 2760 BV (15.45 L) for single Pb(II) polluted battery manufactory wastewater and 2280 BV (12.76 L) for multiple heavy metal polluted estuary effluent, before Pb(II) concentration exceeds the discharge limit of 1 mg/L. Our study demonstrates the great potential of rGOTHs to be applied in practical treatment of wastewater contaminated by heavy metal ions.

Conservative mechanism through various rapeseed (Brassica napus L.) varieties respond to heavy metal (Cadmium, Lead, Arsenic) stress

Introduction

Heavy metal soil pollution is a global issue that can be efficiently tackled through the process of phytoremediation. The use of rapeseed in the phytoremediation of heavy metal-contaminated agricultural land shows great potential. Nevertheless, its ability to tolerate heavy metal stress at the molecular level remains unclear.

Methods

Here, with 7-day seedlings as raw materials, we investigated physiological and biochemical indexes, analyzed the transcriptome sequencing for different treated materials (control, 50×, and 100×), combined with the results of transcriptome and proteome sequencing of the near-isogenic lines (F338 and F335) to reveal the response mechanism to heavy metal stress. Due to oxidative stress response caused by heavy metal stress, there are heavy effects on the emergence of rapeseeds and the growth of seedlings. Although rapeseed can alleviate oxidative stress by enhancing the enzyme activity, especially peroxidase in the oxidation system, this process has its limits. Rapeseed plants activate antioxidase, transport enzymes, and biological regulation to cope with heavy metal stress. Among these responses, peroxidase, ABC transporters, and abscisic acid are particularly significant in this process.

Results and discussion

Based on this study, we identified a breeding material with high adsorption capacity for heavy metals, which contributed to the research on resistance breeding in rapeseed. The results of this study may be useful to alleviate heavy metal soil pollution and tackle edible oil shortages in China.

Recent advances in heavy metals uptake by tailored silica-based adsorbents

In the last decade, numerous designed adsorbent materials like metal-organic frameworks (MOFs), covalent organic frameworks (COF), carbon nanotubes (CNTs), etc. have been developed and investigated for metal ions extraction applications in the contaminated aquatic environment. These materials are facing the problems associated with large-scale production, cost, stability, and reusable. Conventional adsorption like carbon and silica is still valuable and is in use for industrial applications. In the last decade, silica has gone through a lot of alteration and modification to enhance its efficiency for heavy metal adsorption. In this review, the tailoring of the silica properties by surface functionalization or developing new hybrid composites for the scavenging of the heavy have been summarized. Silica functionalization with various organic functional groups, composites like silica/polymers, silica/metal oxide, silica aerogels, etc., has been explored. Moreover, interpretations of the effective metal uptake mechanisms associated with metal ions adsorption onto silica adsorbents are also investigated. Overall, the review offers comprehensive insights into the interface between metal ions and silica-based materials.

Silica-Based Composite Sorbents for Heavy Metal Ions Removal from Aqueous Solutions

Weak polyelectrolyte chains are versatile polymeric materials due to the large number of functional groups that can be used in different environmental applications. Herein, one weak polycation (polyethyleneimine, PEI) and two polyanions (poly(acrylic acid), PAA, and poly(sodium methacrylate), PMAA) were directly deposited through precipitation of an inter-polyelectrolyte coacervate onto the silica surface (IS), followed by glutaraldehyde (GA) crosslinking and extraction of polyanions chains. Four core-shell composites based on silica were synthesized and tested for adsorption of lead (Pb2+) and nickel (Ni2+) as model pollutants in batch sorption experiments on the laboratory scale. The sorbed/desorbed amounts depended on the crosslinking degree of the composite shell, as well as on the type of anionic polyelectrolyte. After multiple loading/release cycles of the heavy metal ions, the maximum sorption capacities were situated between 5-10 mg Pb2+/g composite and 1-6 mg Ni2+/g composite. The strong crosslinked composites (r = 1.0) exhibited higher amounts of heavy metal ions (Me2+) sorbed than the less crosslinked ones, with less PEI on the surface but with more flexible chains being more efficient than more PEI with less flexible chains. Core-shell composites based on silica and weak polyelectrolytes could act as sorbent materials, which may be used in water or wastewater treatment.

Adsorption efficiency of chitosan/clinoptilolite (CS/CZ) composite for effective removal of Cd+2 and Cr+6 ions from wastewater effluents of dairy cattle farms

The wastewater effluent is responsible for the major ecological impact of the dairy sectors. To avoid the negative consequences of heavy metal pollution on the ecosystem, creative, affordable, and efficient treatment methods are now required before the effluent flows into the surrounding area. This study was aimed at assessing the effectiveness of three different adsorbents for Cd+2 and Cr+6 ions from wastewater effluents of dairy farms, including chitosan (CS), clinoptilolite zeolite (CZ), and chitosan/clinoptilolite zeolite (CS/CZ) composite. The adsorption kinetics of the CS/CZ composite were established using the effects of the key variables (pH, agitation speed, adsorbent concentrations, and contact durations). The removal (%) and adsorption capacities, qe (mg/g), were calculated using the data from the adsorption kinetics. Wastewater samples (n = 60) were collected from the wastewater effluents of five farms. Cd+2 and Cr+6 ion concentrations in all collected samples were determined. Following the CS/CZ composite creation, it was characterized using scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (X-RD), and Fourier-transform infrared spectrum (FT-IR). The CS/CZ composite had an adsorption capacity of 92.4 and 96.5 mg/g for both Cd+2 and Cr+6 ions at a concentration of 2.0 g/100 ml, respectively, while the CZ adsorption capacities for the two ions were 87.5 mg/g and 61.0 mg/g, respectively, at 4.0 g/100 ml concentration. The CS was achieved at 55.56 mg/g and 33.3 mg/g, respectively, at the same concentration. The efficiency of heavy metal removal was enhanced by increasing adsorbent concentration, agitation speed, and contact duration. Using CS/CZ composite at 2.0 g/100 ml concentration, 180 min of contact time, and 300 rpm agitation speed, the greatest removal efficiencies for Cd+2 and Cr+6 ions (96.43 and 98.75%, respectively) were demonstrated.

Increasing the sensitivity and accuracy of detecting exosomes as biomarkers for cancer monitoring using optical nanobiosensors

The advancement of nanoscience and material design in recent times has facilitated the creation of point-of-care devices for cancer diagnosis and biomolecule sensing. Exosomes (EXOs) facilitate the transfer of bioactive molecules between cancer cells and diverse cells in the local and distant microenvironments, thereby contributing to cancer progression and metastasis. Specifically, EXOs derived from cancer are likely to function as biomarkers for early cancer detection due to the genetic or signaling alterations they transport as payload within the cancer cells of origin. It has been verified that EXOs circulate steadily in bodily secretions and contain a variety of information that indicates the progression of the tumor. However, acquiring molecular information and interactions regarding EXOs has presented significant technical challenges due to their nanoscale nature and high heterogeneity. Colorimetry, surface plasmon resonance (SPR), fluorescence, and Raman scattering are examples of optical techniques utilized to quantify cancer exosomal biomarkers, including lipids, proteins, RNA, and DNA. Many optically active nanoparticles (NPs), predominantly carbon-based, inorganic, organic, and composite-based nanomaterials, have been employed in biosensing technology. The exceptional physical properties exhibited by nanomaterials, including carbon NPs, noble metal NPs, and magnetic NPs, have facilitated significant progress in the development of optical nanobiosensors intended for the detection of EXOs originating from tumors. Following a summary of the biogenesis, biological functions, and biomarker value of known EXOs, this article provides an update on the detection methodologies currently under investigation. In conclusion, we propose some potential enhancements to optical biosensors utilized in detecting EXO, utilizing various NP materials such as silicon NPs, graphene oxide (GO), metal NPs, and quantum dots (QDs).

Agriculture and environmental management through nanotechnology: Eco-friendly nanomaterial synthesis for soil-plant systems, food safety, and sustainability

Through the advancement of nanotechnology, agricultural and food systems are undergoing strategic enhancements, offering innovative solutions to complex problems. This scholarly essay thoroughly examines nanotechnological innovations and their implications within these critical industries. Traditional practices are undergoing radical transformation as nanomaterials emerge as novel agents in roles traditionally filled by fertilizers, pesticides, and biosensors. Micronutrient management and preservation techniques are further enhanced, indicating a shift towards more nutrient-dense and longevity-oriented food production. Nanoparticles (NPs), with their unique physicochemical properties, such as an extraordinary surface-to-volume ratio, find applications in healthcare, diagnostics, agriculture, and other fields. However, concerns about their potential overuse and bioaccumulation raise unanswered questions about their health effects. Molecule-to-molecule interactions and physicochemical dynamics create pathways through which nanoparticles cause toxicity. The combination of nanotechnology and environmental sustainability principles leads to the examination of green nanoparticle synthesis. The discourse extends to how nanomaterials penetrate biological systems, their applications, toxicological effects, and dissemination routes. Additionally, this examination delves into the ecological consequences of nanomaterial contamination in natural ecosystems. Employing robust risk assessment methodologies, including the risk allocation framework, is recommended to address potential dangers associated with nanotechnology integration. Establishing standardized, universally accepted guidelines for evaluating nanomaterial toxicity and protocols for nano-waste disposal is urged to ensure responsible stewardship of this transformative technology. In conclusion, the article summarizes global trends, persistent challenges, and emerging regulatory strategies shaping nanotechnology in agriculture and food science. Sustained, in-depth research is crucial to fully benefit from nanotechnology prospects for sustainable agriculture and food systems.

Adsorption of Co2+ and Cr3+ in Industrial Wastewater by Magnesium Silicate Nanomaterials

In this paper, two flower-like magnesium silicate nanomaterials were prepared. These and another two commercial magnesium silicate materials were characterized using a scanning electron microscope, the N2 adsorption-desorption method, and other methods. The structure-activity relationship between the adsorption performance of these four magnesium silicate materials and their specific surface area, pore size distribution, and pore structure was compared. The results showed that the 3-FMS modified by sodium dodecyl sulfonate (SDS) had the largest specific surface area and pore size, the best adsorption performance, and the largest experimental equilibrium adsorption capacity (qe,exp) for Co2+, reaching 190.01 mg/g, and Cr3+, reaching 208.89 mg/g. The adsorption behavior of the four materials for Co2+ and Cr3+ both fitted the pseudo-second-order kinetic model and Langmuir adsorption model, indicating that chemical monolayer uniform adsorption was the dominant adsorption process. Among them, the theoretical adsorption capacity (qm) of 3-FMS was the highest, reaching 207.62 mg/g for Co2+ and 230.85 mg/g for Cr3+. Through further research, it was found that the four materials mainly removed Co2+ and Cr3+ through electrostatic adsorption, surface metal ions (Mg2+), and acidic groups (-OH and -SO3H) exchanging with ions in solution. The adsorption performance of two self-made flower-like magnesium silicate materials for Co2+ and Cr3+ was superior to that of two commercial magnesium silicates.

New horizons on advanced nanoscale materials for Cultural Heritage conservation

Nanomaterials have permeated numerous scientific and technological fields, and have gained growing importance over the past decades also in the preservation of Cultural Heritage. After a critical overview of the main nanomaterials adopted in art preservation, we provide new insights into some highly relevant gels, which constitute valuable tools to selectively remove dirt or other unwanted layers from the surface of works of art. In particular, the recent "twin-chain" gels, obtained by phase separation of two different PVAs and freeze-thawing, were considered as the most performing gel systems for the cleaning of Cultural Heritage. Three factors are crucial in determining the final gel properties, i.e., pore size, pore connectivity, and surface roughness, which belong to the micro/nanodomain. The pore size is affected by the molecular weight of the phase-separating PVA polymer, while pore connectivity and tortuosity likely depend on interconnections formed during gelation. Tortuosity greatly impacts on cleaning capability, as the removal of matter at the gel-target interface increases with the uploaded fluid's residence time at the interface (higher tortuosity produces longer residence). The gels' surface roughness, adaptability and stickiness can also be controlled by modulating the porogen amount or adding different polymers to PVA. Finally, PVA can be partially replaced with different biopolymers yielding gels with enhanced sustainability and effective cleaning capability, where the selection of the biopolymer affects the gel porosity and effectiveness. These results shed new light on the effect of micro/nanoscale features on the cleaning performances of "twin-chain" and composite gels, opening new horizons for advanced and "green"/sustainable gel materials that can impact on fields even beyond art preservation, like drug-delivery, detergency, food industry, cosmetics and tissue engineering.

Impact of calcium ions at physiological concentrations on the adsorption behavior of proteins on silica nanoparticles

The adsorption of proteins on nanoparticles (NPs) largely decides the fate and bioeffects of NPs in vivo. However, bio-fluids are too complicated to directly study in them to reveal related mechanisms, and current studies on model systems often ignore some important biological factors, such as metal ions. Herein, we evaluate the effect of Ca2+ at physiological concentrations on the protein adsorption on negatively-charged silica NP (SNP50). It is found that Ca2+, as well as Mg2+ and several transition metal ions, significantly enhances the adsorption of negatively-charged proteins on SNP50. Moreover, the Ca2+-induced enhancement of protein adsorption leads to the reduced uptake of SNP50 by HeLa cells. A double-chelating mechanism is proposed for the enhanced adsorption of negatively-charged proteins by multivalent metal ions that can form 6 (or more) coordinate bonds, where the metal ions are chelated by both the surface groups of NPs and the surface residues of the adsorbed proteins. This mechanism is consistent with all experimental evidences from metal ions-induced changes of physicochemical properties of NPs to protein adsorption isotherms, and is validated with several model proteins as well as complicated serum. The findings highlight the importance of investigating the influences of physiological factors on the interaction between proteins and NPs.

Advancement in nanomaterials for environmental pollutants remediation: a systematic review on bibliometrics analysis, material types, synthesis pathways, and related mechanisms

Environmental pollution is a major issue that requires effective solutions. Nanomaterials (NMs) have emerged as promising candidates for pollution remediation due to their unique properties. This review paper provides a systematic analysis of the potential of NMs for environmental pollution remediation compared to conventional techniques. It elaborates on several aspects, including conventional and advanced techniques for removing pollutants, classification of NMs (organic, inorganic, and composite base). The efficiency of NMs in remediation of pollutants depends on their dispersion and retention, with each type of NM having different advantages and disadvantages. Various synthesis pathways for NMs, including traditional synthesis (chemical and physical) and biological synthesis pathways, mechanisms of reaction for pollutants removal using NMs, such as adsorption, filtration, disinfection, photocatalysis, and oxidation, also are evaluated. Additionally, this review presents suggestions for future investigation strategies to improve the efficacy of NMs in environmental remediation. The research so far provides strong evidence that NMs could effectively remove contaminants and may be valuable assets for various industrial purposes. However, further research and development are necessary to fully realize this potential, such as exploring new synthesis pathways and improving the dispersion and retention of NMs in the environment. Furthermore, there is a need to compare the efficacy of different types of NMs for remediating specific pollutants. Overall, this review highlights the immense potential of NMs for mitigating environmental pollutants and calls for more research in this direction.

Optimal synthesis of dolochar derived faujasite zeolite X for highly effective Cd(II) removal

Cadmium-induced water pollution is a major environmental issue because of its persistent nature and adverse ecological impacts. Adsorption is a highly favored method due to its versatility and high efficacy in cadmium removal. Hence, the present work aims to develop a low-cost, highly effective adsorbent-dolochar-derived nanoporous zeolite to easily and effectively purify Cd(II) polluted water. The work focuses on the Cd(II) batch adsorption study using the optimal hydrothermal synthesis of a crystalline faujasite Zeolite X (ZX) from dolochar. The synthesis parameters were optimized using Response Surface Methodology, specifically Box Behnken Design (RSM-BBD), to maximize the crystallinity percentage. Variables such as initial Cd(II) concentration, solution pH, dosage, time, and temperature were studied for the Cd(II) batch adsorption study. The optimum conditions for synthesizing ZX include NaOH/Dolochar, crystallization temperature, and crystallization time of 1.375, 100 °C, and 11 h, respectively. The resultant XRD structure exhibited an average crystal size and crystallinity of 0.79 μm and 87.231 %, respectively. The average pore size, micropore volume, micropore area, and total surface area were 3.316 nm, 0.311 cc. g-1, 567.226 m2 g-1, and 583.117 m2 g-1, respectively. The maximum removal was accomplished with optimum conditions of 0.25 g.L-1 dosage, 80 min, at 313.15 K, and 6.5 pH. Adsorption isotherm results agreed with those hypothesized by Freundlich isotherm, with a maximum adsorption capacity of 714.285 mg g-1, and the pseudo-second-order kinetic model describes the adsorption kinetics well. The relevance of the results highlights the importance of using this dolochar-derived nanoporous zeolite as an adsorbent to effectively treat Cd(II) containing wastewater.

Performance and cell toxicity studies for the use of graphene oxide-bimetallic oxide hybrids in the absorptive removal of Pb(II) from wastewater: fixed-bed column study with regeneration

The current study involves the removal of Pb(II) ions from an aqueous solution using GO/Mn-Fe hybrids in a fixed bed column study. The capability of the hybrid in the Pb removal was examined using a continuous flow fixed bed column which revealed that the hybrid had the maximum adsorption capacity of 172.768 mg/g at a flow rate of 2 mL/min, bed height of 1 cm, and influent concentration of 200 mg/L. The breakthrough curves obtained from the experiments were examined using three different models, i.e., Bohart-Adams model, Thomas Model, and Yoon-Nelson model, wherein all the models showed high correlation coefficient values. Three consecutive adsorption-desorption cycles in the column yielded regeneration efficiencies of 91.71%, 88.31%, and 85.41%. The column life factor indicated that the fixed bed would have enough capacity to avoid a zero breakthrough time for up to 9 cycles, implying that GO/Mn-Fe could be used as a cheap and efficient adsorbent in the removal of Pb(II) from contaminated water. The adsorption mechanism was postulated based on the characterization of the spent adsorbent by FTIR and SEM. The phenomenon of the adsorption process can be described in accordance with the surface complex formation theory, which suggests that an increase in pH decreases the competition between metal ions and protons, favoring metal ion adsorption. The toxicity of the synthesized hybrid was evaluated on HeLa cells and compared to the toxicity of GO. Increasing the concentration of GO/Mn-Fe hybrid from 50 to 250 g/mL resulted in a decrease in cell viability from 91.90 to 56.52%, whereas increasing the concentration of GO resulted in a decrease in cell viability from 61.59 to 37.19%. The study clearly demonstrates the use of GO/Mn-Fe hybrid as an adsorbent for efficient sequestration of Pb(II) ions with lower environmental toxicity.

Single-shot multi-channel plasmonic real-time polymerase chain reaction for multi-target point-of-care testing

Plasmonic nucleic acid amplification tests demand high-throughput and multi-target detection of infectious diseases as well as short turnaround time and small size for point-of-care molecular diagnostics. Here, we report a multi-channel plasmonic real-time reverse-transcription polymerase chain reaction (mpRT-qPCR) assay for ultrafast and on-chip multi-target detection. The mpRT-qPCR system features two pairs of plasmonic thermocyclers for rapid nanostructure-driven amplification and microlens array fluorescence microscopes for in situ multi-color fluorescence quantification. Each channel shows a physical dimension of 32 mm, 75 mm, and 25 mm in width, length, and thickness. The ultrathin microscopes simultaneously capture four different fluorescence images from two PCR chambers of a single cartridge at a single shot exposure per PCR cycle of four different excitation light sources. The experimental results demonstrate a single assay result of high-throughput amplification and multi-target quantification for RNA-dependent RNA polymerase, nucleocapsid, and human ribonuclease P genes in SARS-CoV-2 RNA detection. The mpRT-PCR increases the number of tests four times over the single RT-PCR and exhibits a short detection time of 15 min for the four RT-PCR reactions. This point-of-care molecular diagnostic platform can reduce false negative results in clinical applications of virus detection and decentralize healthcare facilities with limited infrastructure.

Copper biosorption by Bacillus pumilus OQ931870 and Bacillus subtilis OQ931871 isolated from Wadi Nakheil, Red Sea, Egypt

BACKGROUND

Despite being necessary, copper is a toxic heavy metal that, at high concentrations, harms the life system. The parameters that affect the bioreduction and biosorption of copper are highly copper-resistant bacteria.

RESULTS

In this work, the ability of the bacterial biomass, isolated from black shale, Wadi Nakheil, Red Sea, Egypt, for Cu2+ attachment, was investigated. Two Cu2+ resistance Bacillus species were isolated; Bacillus pumilus OQ931870 and Bacillus subtilis OQ931871. The most tolerant bacterial isolate to Cu2+ was B. pumilus. Different factors on Cu2+ biosorption were analyzed to estimate the maximum conditions for Cu biosorption. The qmax for Cu2+ by B. pumilus and B. subtilis determined from the Langmuir adsorption isotherm was 11.876 and 19.88 mg. g-1, respectively. According to r2, the biosorption equilibrium isotherms close-fitting with Langmuir and Freundlich model isotherm. Temkin isotherm fitted better to the equilibrium data of B. pumilus and B. subtilis adsorption. Additionally, the Dubinin-Radushkevich (D-R) isotherm suggested that adsorption mechanism of Cu2+ is predominately physisorption.

CONCLUSION

Therefore, the present work indicated that the biomass of two bacterial strains is an effective adsorbent for Cu2+ removal from aqueous solutions.

Biogenesis, Isolation, and Detection of Exosomes and Their Potential in Therapeutics and Diagnostics

The increasing research and rapid developments in the field of exosomes provide insights into their role and significance in human health. Exosomes derived from various sources, such as mesenchymal stem cells, cardiac cells, and tumor cells, to name a few, can be potential therapeutic agents for the treatment of diseases and could also serve as biomarkers for the early detection of diseases. Cellular components of exosomes, several proteins, lipids, and miRNAs hold promise as novel biomarkers for the detection of various diseases. The structure of exosomes enables them as drug delivery vehicles. Since exosomes exhibit potential therapeutic applications, their efficient isolation from complex biological/clinical samples and precise real-time analysis becomes significant. With the advent of microfluidics, nano-biosensors are being designed to capture exosomes efficiently and rapidly. Herein, we have summarized the history, biogenesis, characteristics, functions, and applications of exosomes, along with the isolation, detection, and quantification techniques. The implications of surface modifications to enhance specificity have been outlined. The review also sheds light on the engineered nanoplatforms being developed for exosome detection and capture.

Synthesizing sulfhydryl-functionalized biochar for effectively removing mercury ions from contaminated water

Biochar is regarded as an effective adsorbent for heavy metal pollution treatment, and functional optimization is still needed to improve its performance. We created raw biochar (BC and BP) from corn straw and pine sawdust, which were modified to produce sulfhydryl-modified biochar (MBC and MBP). Isothermal adsorption experiments and adsorption kinetics experiments as well as the related model fitting were performed to evaluate the adsorption performance of biochar on Hg(II). According to the results of the Langmuir model fitting, the maximum adsorption capacities of sulfhydryl-modified biochar were 193.05 mg/g (MBC) and 178.04 mg/g (MBP), respectively, which were approximately 1.6 times higher than the raw biochar. The results showed that adding sulfhydryl groups to biochar can improve its adsorption performance. The prompt effect resulted from the sulfhydryl modification providing additional functional groups and enhanced chemisorption and physical adsorption properties.

Synthesis of iron oxide nanoparticles mediated by Camellia sinensis var. Assamica for Cr(VI) adsorption and detoxification

Environment-benign synthesis of nanoparticles (NPs) are of great importance. Plant-based polyphenols (PPs) are electron donor analytes for the synthesis of metal and metal oxide NPs. This work produced and investigated iron oxide nanoparticles (IONPs) from PPs of tea leaves of Camellia sinensis var. assamica for Cr(VI) removal. The conditions for IONPs synthesis were using RSM CCD and found to be optimum at a time of 48 min, temperature of 26 °C, and iron precursors/leaves extract ratio (v/v) of 0.36. Further, these synthesized IONPs at a dosage of 0.75 g/L, temperature of 25 °C, and pH 2 achieved a maximum of 96% Cr(VI) removal from 40 mg/L of Cr(VI) concentration. The exothermic adsorption process followed the pseudo-second-order model, and Langmuir isotherm estimated a remarkable maximum adsorption capacity (Q_m) of 1272 mg g^-1 of IONPs. The proposed mechanistic for Cr(VI) removal and detoxification involved adsorption and its reduction to Cr(III), followed by Cr(III)/Fe(III) co-precipitation.

Fast Microwave-Assisted Synthesis, Calcination and Functionalization of a Silica Mesoporous Nanomaterial: UVM-7

We report here, for the first time, the use of a solid state microwave source for the synthesis, calcination and functionalization of a UVM-7 based hybrid mesoporous silica material. The synthesis of the UVM-7 material is obtained in 2 min at low power (50 W) by the combination of a microwave irradiation and the atrane route. Moreover, it has been successfully calcined and functionalized in just 13 and 4 min respectively with microwave assisted procedures. A total synthesis comprising each individually optimized step, can be executed in only 4 h including work-up, by contrast to a typical synthesis that comprises several days. Savings higher than one order or magnitude are obtained in time and energy. Our example is a proof of concept of the potential use of solid state microwave generators for the ultrafast on-command preparation of hybrid nanomaterials due to their accurate control and accelerating properties.

A novel and capable supported phenylazophenylenediamine-based nano-adsorbent for removal of the Pb, Cd, and Ni ions from aqueous solutions

Herein, we report the synthesis and characterization of chrysoidine (4-phenylazo-m-phenylenediamine) grafted on magnetic nanoparticles (Fe₃O₄@SiO₂@CPTMS@PhAzPhDA = FeSiPAPDA) as a novel and versatile adsorbent used for the satisfactory removal of Pb, Ni, and Cd ions from contaminated water via the formation of their complexes. The Freundlich, Langmuir, Temkin, and Redlich-Patterson isotherm models were studied to reveal the adsorption capability of the adsorbent and were found out that the Langmuir model is more compatible with the nano-adsorbent behavior. Moreover, according to the ICP tests as well as based on the Langmuir isotherm, the maximum adsorption capacity of the FeSiPAPDA-based adsorbent for the Pb ions (97.58) is more than that of Cd (78.59) and Ni ions (64.03).

Life Cycle Assessment as Support Tool for Development of Novel Polyelectrolyte Materials Used for Wastewater Treatment

This life cycle assessment (LCA) study focused on comparing the environmental performances of two types of synthesis strategies for polyethyleneimine (PEI) coated silica particles (organic/inorganic composites). The classic layer-by-layer and the new approach (one-pot coacervate deposition) were the two synthesis routes that were tested for cadmium ions removal from aqueous solutions by adsorption in equilibrium conditions. Data from the laboratory scale experiments for materials synthesis, testing, and regeneration, were then fed into a life cycle assessment study so that the types and values of environmental impacts associated with these processes could be calculated. Additionally, three eco-design strategies based on material substitution were investigated. The results point out that the one-pot coacervate synthesis route has considerably lower environmental impacts than the layer-by-layer technique. From an LCA methodology point of view, it is important to consider material technical performances when defining the functional unit. From a wider perspective, this research is important as it demonstrates the usefulness of LCA and scenario analysis as environmental support tools for material developers because they highlight environmental hotspots and point out the environmental improvement possibilities from the very early stages of material development.

Engineering the Performance and Stability of Molybdenum Disulfide for Heavy Metal Removal

Molybdenum disulfide (MoS₂) has recently emerged as one of the most promising water nano-based adsorbent materials for heavy metal removal with the potential to provide an alternative to conventional water decontamination technologies. In this study, we demonstrate the trade-off between mercuric removal capacity and overall MoS₂ adsorbent stability, both driven by MoS₂ synthesis parameters. A bottom-up hydrothermal synthesis setup at various growth temperatures was employed to grow flower-like MoS₂ films onto planar alumina supports. A thorough material characterization suggests that an increase in growth temperature from 150 to 210 °C results in higher MoS₂ crystallinity. Interestingly, elevated growth temperatures resulted in poor mercuric removal (525 mg g^-1, K = 2.2 × 10^-3 h^-1), yet showed enhanced chemical stability (i.e., minimal molybdenum leaching during exposure to mercury). On the other hand, low growth temperatures produce amorphous supported MoS₂, exhibiting superb mercuric removal capabilities (5158 mg g^-1, K = 36.1 × 10^-3 h^-1) but displaying poor stability, resulting in substantial byproduct molybdate leaching. Mercuric removal by crystalline MoS₂ was accomplished by adsorption and electrostatic attraction-based removal mechanisms, whereas redox reactions and HgS crystallization-based removal mechanisms were more dominant when using amorphous MoS₂ for mercury removal. Overall, our study provides essential insights into the delicate balance between MoS₂ mercuric removal capabilities and MoS₂ degradation, both related to material synthesis growth conditions. Employment of nano-enabled water treatments in general, and MoS₂ for heavy metal removal in particular, requires us to better understand these important fundamental trade-off behaviors to achieve sustainable, effective, and responsible implementation of nanotechnologies in large scale systems.

Enhanced production of biosurfactant by Bacillus subtilis RSL2 in semicontinuous bioreactor utilizing molasses as a sole substrate

The growth-associated metabolites are produced during the exponential phase; however, this phase terminates due to substrate depletion or product inhibition. In the present study, a semicontinuous mode with a fill-and-draw strategy was applied to extend the exponential phase of the biosurfactant production to overcome the product inhibition and in turn, enhance the yield. Bioreactor studies were performed in batch mode, followed by the semicontinuous operation. A potential biosurfactant producer Bacillus subtilis RSL2 was used in this study at the previously optimized conditions of pH 6.6, temperature 41 °C and 5% (w/v) of molasses. A better mass transfer was achieved in the bioreactor as compared to the shake flask study. In the batch bioreactor study, 90% of sugar was utilized with simultaneous 13.7 g L^-1 of biosurfactant production. The sugar utilization was further improved to > 98% in the case of semicontinuous operation employing a fill-and-draw strategy. The exponential phase got extended up to 18 days and a total of 13 L of media was fed in the semicontinuous operation of 21 days as compared to 1.5 L of working volume in the batch reactor. The biosurfactant yield was enhanced by 1.5 folds and was found to be 0.97 g g^-1. The produced biosurfactant was identified as a lipopeptide. The interfacial properties of the biosurfactant along with colloidal and thermal stability have been investigated. The critical micelle concentration of the produced biosurfactant was 70 mg L^-1. The present study highlighted the efficient utilization of molasses for the production of biosurfactant, an alternative metabolite, in a semicontinuous mode of bioreactor.

Removal of Pb2+, CrT, and Hg2+ Ions from Aqueous Solutions Using Amino-Functionalized Magnetic Nanoparticles

In this paper, a circular economy approach with the adsorption and desorption of heavy metal (HM) ions—i.e., lead (Pb2+), chromium (CrT), and mercury (Hg2+)—from aqueous solutions was studied. Specific and selective binding of HM ions was performed on stabilized and amino-functionalized iron oxide magnetic nanoparticles (γ-Fe2O3@NH2 NPs) from an aqueous solution at pH 4 and 7. For this purpose, γ-Fe2O3@NH2 NPs were characterized by thermogravimetric analysis (TGA), Fourier-transform infrared spectroscopy (FTIR), specific surface area (BET), transmission electron microscopy (TEM), EDXS, and zeta potential measurements (ζ). The effects of different adsorbent amounts (mads = 20/45/90 mg) and the type of anions (NO3−, Cl−, SO42−) on adsorption efficiency were also tested. The desorption was performed with 0.1 M HNO3. The results showed improvement of adsorption efficiency for CrT, Pb2+, and Hg2+ ions at pH 7 by 45 mg of g-Fe2O3@NH2 NPs, and the sequence was as follows: CrT > Hg2+ > Pb2+, with adsorption capacities of 90.4 mg/g, 85.6 mg/g, and 83.6 mg/g, respectively. The desorption results showed the possibility for the reuse of γ-Fe2O3@NH2 NPs with HNO3, as the desorption efficiency was 100% for Hg2+ ions, 96.7% for CrT, and 91.3% for Pb2+.

Antimicrobial Agents Based on Metal Complexes: Present Situation and Future Prospects

The rise in antimicrobial resistance is a cause of serious concern since the ages. Therefore, a dire need to explore new antimicrobial entities that can combat against the increasing threat of antibiotic resistance is realized. Studies have shown that the activity of the strongest antibiotics has reduced drastically against many microbes such as microfungi and bacteria (Gram-positive and Gram-negative). A ray of hope, however, was witnessed in early 1940s with the development of new drug discovery and use of metal complexes as antibiotics. Many new metal-based drugs were developed from the metal complexes which are potentially active against a number of ailments such as cancer, malaria, and neurodegenerative diseases. Therefore, this review is an attempt to describe the present scenario and future development of metal complexes as antibiotics against wide array of microbes.

The highly efficient simultaneous removal of Pb2+ and methylene blue induced by the release of endogenous active sites of montmorillonite

The inherent periodic structure of montmorillonite limits the adsorption capacity of its endogenous active units such as Si-O tetrahedron and Al-O octahedron for pollutants. The high-intensity ultrasound method was used to release these active units and the layer-by-layer assembly was adopted to prepare carbon@chitosan@montmorillointe microsphere adsorbent (C@CS@Mt) to give full play to the adsorption capacity of montmorillonite. The montmorillonite nanosheet exhibited good hole-making ability, resulting in high surface area, pore volume and pore diameter of microspheres. Benefitting from the release of active sites in Si-O tetrahedron and Al-O octahedron of montmorillonite nanosheets, the adsorption capacity of C@CS@Mt was significantly improved. The maximum adsorption capacities of Pb²⁺ and methylene blue (MB) reached 884.19 mg·g^-1 and 326.21 mg·g^-1, respectively. The simultaneous adsorption experiments indicated that the occupation of active sites by Pb²⁺ caused the observed decrease of MB adsorption capacity. The theoretical calculations indicated that Pb was preferentially adsorbed by active adsorption units due to strong electron donating ability in comparison to MB. As an active unit, Si-O tetrahedron exhibited stronger adsorption capacity for cationic dyes than Al-O octahedron due to both the large electronegativity and lower adsorption binding energy.

Development of Adsorptive Materials for Selective Removal of Toxic Metals in Wastewater: A Review

Removal of toxic metals is essential to achieving sustainability in wastewater purification. The achievement of efficient treatment at a low cost can be seriously challenging. Adsorption methods have been successfully demonstrated for possession of capability in the achievement of the desirable sustainable wastewater treatment. This review provides insights into important conventional and unconventional materials for toxic metal removal from wastewater through the adsorption process. The importance of the role due to the application of nanomaterials such as metal oxides nanoparticle, carbon nanomaterials, and associated nanocomposite were presented. Besides, the principles of adsorption, classes of the adsorbent materials, as well as the mechanisms involved in the adsorption phenomena were discussed.

Novel GO/Fe-Mn hybrid for the adsorptive removal of Pb(II) ions from aqueous solution and the spent adsorbent disposability in cement mix: compressive properties and leachability study for circular economy benefits

GO/Fe-Mn hybrids were prepared by a single-pot chemical precipitation method and were characterized using FTIR, XRD, Raman, zeta potential, and FESEM, which confirmed the impregnation of Fe/Mn onto GO sheets. The synthesized hybrids were successively applied in removing the Pb(II) ions from aqueous solution and later utilizing the spent adsorbent to increase the properties of cement. The adsorption capability of the synthesized hybrid was seen in a set of batch studies to find out that about 15 min of contact time was required to remove 99% of the contaminant at a pH of 5 ± 0.2 and a dose of 0.83 g/L. The mechanism of the adsorption process for the synthesized hybrid was well described by Elovich kinetic model with an R² of 0.99 and Langmuir isotherm model, also with an R² of 0.99. The desorption studies conducted using 0.1 M HCl solution showed significant stability of the hybrid with a drop of 12% in the removal efficiency of Pb after up to five adsorption-desorption cycles. This points to an efficient adsorbent having potential for economical use. Later, the spent adsorbent was mixed with cement at ratios of 0.05%, 0.1%, and 0.5%, and compressive strength tests were performed, which showed an increase in the strength by 7.62%, 16.11%, and 26.82% at 28 days of curing time. The TCLP and SPLP tests performed on the hybrid and cement-spent adsorbent mix showed all the leaching parameters were well within the permissible limits. This development shows the potential for the use of spent adsorbent in a circular economy model.

A critical and recent developments on adsorption technique for removal of heavy metals from wastewater-A review

This review provides a quantitative description of the nano-adsorbent processing and its viability against wastewater detoxification by extracting heavy metal ions. The impact of nano-adsorbent functionalities on specific essential attributes such as the surface area, segregation, and adsorption capacity were comprehensively evaluated. A detailed analysis has been presented on the characteristics of nanomaterials through their limited resistance to adsorb some heavy metal ions. Experimental variables such as the adsorbent dosage, pH, substrate concentration, response duration, temperature, and electrostatic force that influence the uptake of metal ions have been studied. Besides, separate models for the adsorption kinetics and isothermal adsorption have been investigated to understand the mechanism behind adsorption. Here, we reviewed the different adsorbent materials with nano-based techniques for the removal of heavy metals from wastewater and especially highlighted the nano adsorption technique. The influencing factors such as pH, temperature, dosage time, sorbent dosage, adsorption capacities, ion concentration, and mechanisms related to the removal of heavy metals by nano composites are highlighted. Lastly, the application potentials and challenges of nano adsorption for environmental remediation are discussed. This critical review would benefit engineers, chemists, and environmental scientists involved in the utilization of nanomaterials for wastewater treatment.

Covalent and Non-covalent Functionalized Nanomaterials for Environmental Restoration

Nanotechnology has emerged as an extraordinary and rapidly developing discipline of science. It has remolded the fate of the whole world by providing diverse horizons in different fields. Nanomaterials are appealing because of their incredibly small size and large surface area. Apart from the naturally occurring nanomaterials, synthetic nanomaterials are being prepared on large scales with different sizes and properties. Such nanomaterials are being utilized as an innovative and green approach in multiple fields. To expand the applications and enhance the properties of the nanomaterials, their functionalization and engineering are being performed on a massive scale. The functionalization helps to add to the existing useful properties of the nanomaterials, hence broadening the scope of their utilization. A large class of covalent and non-covalent functionalized nanomaterials (FNMs) including carbons, metal oxides, quantum dots, and composites of these materials with other organic or inorganic materials are being synthesized and used for environmental remediation applications including wastewater treatment. This review summarizes recent advances in the synthesis, reporting techniques, and applications of FNMs in adsorptive and photocatalytic removal of pollutants from wastewater. Future prospects are also examined, along with suggestions for attaining massive benefits in the areas of FNMs.

Natural and Engineered Nanomaterials for the Identification of Heavy Metal Ions—A Review

In recent years, there has been much interest in developing advanced and innovative approaches for sensing applications in various fields, including agriculture and environmental remediation. The development of novel sensors for detecting heavy metals using nanomaterials has emerged as a rapidly developing research area due to its high availability and sustainability. This review emphasized the naturally derived and engineered nanomaterials that have the potential to be applied as sensing reagents to interact with metal ions or as reducing and stabilizing agents to synthesize metallic nanoparticles for the detection of heavy metal ions. This review also focused on the recent advancement of nanotechnology-based detection methods using naturally derived and engineered materials, with a summary of their sensitivity and selectivity towards heavy metals. This review paper covers the pros and cons of sensing applications with recent research published from 2015 to 2022.

Efficient and Fast Removal of Aqueous Tungstate by an Iron-Based LDH Delaminated in L-Asparagine

High concentrations of tungstate in aqueous systems pose a severe threat to the environment and human health. This study explored the potential of iron-based LDHs to remove tungstate from water. To improve its tungstate uptake capacity, environment-friendly L-asparagine was used to delaminate iron-based LDH synthesized via a coprecipitation method. The successful delamination was proved by AFM, revealing that the thickness of the obtained nanoparticles was approximately 1–2 times that of a single LDH layer. XRD, TEM, and XPS analyses confirmed that the delaminated LDHs were amorphous and ultrathin and had surface defects within their nanosheets that acted as active sites, leading to a very fast tungstate sorption rate and superior tungstate uptake capacity. Notably, the original layered structure of the L-asparagine-treated LDH was recovered upon its reaction with tungstate-bearing solutions, and therefore, the high availability of aqueous tungstate to the interlayer regions during the structural restoration of the delaminated iron-based LDH contributed to its excellent capability of tungstate removal as well. In addition, the tungstate uptake by the delaminated iron-based LDH was not affected substantially by the presence of coexisting anions, implying that the strong inner-sphere complexation between the tungstate and LDH layers with defects (i.e., Fe-O bonds) was the primary mechanism responsible for the tungstate removal. The delamination process described in this paper was validated to be an effective way to enhance the immobilization of tungstate by iron-based LDHs without inducing secondary pollutions, and delaminated iron-based LDHs are promising to be used extensively in the practice of treating tungstate-rich waters.

O, N-doped porous biochar by air oxidation for enhancing heavy metal removal: The role of O, N functional groups

Oxygen- and nitrogen-doped porous oxidized biochar (O,N-doped OBC) was fabricated in this study. Biochar (BC) can be enriched in surface functional groups (O and N) and the porosity can be improved by a simple, convenient and green procedure. BC was oxidized at 200 °C in an air atmosphere with quality control via oxidation time changes. As the oxidation time increased, the O and N contents and porosity of the materials improved. After 1.5 h of oxidation, the O and N contents of O,N-doped OBC-1.5 were 54.4% and 3.9%, higher than those of BC, which were 33.4% and 1.8%, respectively. The specific surface area and pore volume of O,N-doped OBC-1.5 were 88.5 m² g^-1 and 0.07 cm³ g^-1, respectively, which were greater than those of BC. The improved surface functionality and porosity resulted in an increased heavy metal removal efficiency. As a result, the maximum adsorption capacity of Cu(II) by O,N-doped OBC was 23.32 mg L^-1, which was twofold higher than that of pristine BC. Additionally, for a multiple ion solution, O,N-doped OBC-1.5 showed a greater adsorption behavior toward Cu(II) than Zn(II) and Ni(II). In a batch experiment, the concentration of Cu(II) decreased 92.3% after 90 min. In a filtration experiment, the O,N-doped OBC-based filter achieved a Cu(II) removal capacity of 12.90 mg g^-1 and breakthrough time after 250 min. Importantly, the chemical mechanism was mainly governed by monolayer adsorption of Cu(II) onto a homogeneous surface of O,N-doped OBC-1.5. Surface complexation and electrostatic attraction were considered to be the chemical mechanisms governing the adsorption process.

Low-temperature synthesis of functionalized activated carbon from blackboard (Alstonia scholaris) with improved selectivity for 2-methylpyridine removal: batch and column analyses

Coal tar industry has been reported to discharge 2-methylpyridine (2Mp) in concentrations up to 150 mg L^-1. For removal of 2Mp, activated carbon was synthesized from blackboard tree ground bark (BA) by the novel technique of prior cooling (which helped decrease heat generation and volatile gas emission). The material was successfully functionalized with carboxylic group which enhanced 2Mp uptake. Batch sorption of 2Mp was carried out on both BA and carboxyl functionalized BA (CFA). Acetonitrile-water (55:45) was used as eluent in uHPLC quantification of 2Mp. Interaction mechanism of 2Mp with both sorbents was studied by using characterization techniques (SEM, FTIR and EDS). Carboxyl groups present on CFA were found to interact with 2Mp molecules, leading to their removal from synthetic solution. Carboxylation helped in lowering the intrinsic moisture content of the sorbent. Proton leaching from carboxyl groups of CFA was found to be negligible. Specific surface areas for CFA and BA were found as 211.15 m² g^-1 and 156.32 m² g^-1, respectively. Batch experimentation showed that CFA had twice the adsorption capacity compared to BA (27.0 and 15.5 mg g^-1, respectively). Pseudo-second-order kinetics and Langmuir isotherm-based equilibria were observed. Intraparticle diffusion was the rate-limiting step. Top-down fixed bed studies were performed using a 2-cm-diameter column by varying flow rate, bed depth and 2Mp concentration, respectively. The Thomas model could successfully emulate the steep slopes of the breakthrough curves, implying good sorbent saturation.

Detection and Prediction of HMS from Drinking Water by Analysing the Adsorbents from Residuals Using Deep Learning

Contamination HM is an important issue associated with the environment, and it requires suitable steps for the reduction of HMs in water at an acceptable ratio. With modern technologies, this could be possible by enabling the carbon adsorbents to adsorb the pollutions via deep learning strategies. In this paper, we develop a model on detection and prediction of presence of HMs from drinking water by analysing the adsorbents from residuals using deep learning. The study uses dense neural networks or DenseNets to analyse the microscopic images of the residual adsorbents. The study initially preprocesses and extracts features using standardised procedure. The DenseNets are used finally for detection purpose, and it is trained and tested with standard set of microscopic images. The experimental results are conducted to test the efficacy of the deep learning model on detecting the HM composition. The results of simulation show that the proposed deep learning model achieves 95% higher rate of detecting the HM composition from the adsorption residuals than other methods.

Sorption based easy-to-use low-cost filters derived from invasive weed biomass for dye contaminated water cleanup

Today, the development of functional nanostructured materials with specified morphologies utilizing environmentally friendly techniques is a very appealing topic in materials chemistry. Much emphasis has recently been paid to the utilization of biomass to make functional carbonaceous materials of varying forms, specifically carbon helices, with greater implications for the environment, economy, and society. A metal-catalyzed chemical vapour deposition technique has been developed for the fabrication of such carbon helices from nonrenewable hydrocarbons. Also, functionalization approaches were seen to necessitate high temperatures, hazardous gases, and multi-step processes. Herein, we have synthesized tendril-like functional carbon helices (HTCs) from toxic bio-weed, Parthenium hysterophorus as the carbon source by a greener solvothermal method employing deep eutectic solvent (DES) as both soft template and catalyst. Further, for the first time by taking advantage of the in-built chemical functionalities, HTCs were physically activated in an inert atmosphere at 900 °C (AHC) and functionalized with manganese oxide at room temperature by employing DES. Furthermore, the materials were characterized using FE-SEM, EDX, FT-IR, XRD, and BET analysis, where a surface area of 313.12 m2 g-1 was achieved with a robust removal of 99.68% of methylene blue (MB) dye with a flux rate of 7432.71 LMH in a simulated continuous flow system. The obtained material was also evaluated for its specificity towards contaminant removal from an aqueous medium. Thus, Mn3O4/AHC membranes exhibited great promise as an easy-to-use filter for organic contaminant cleanup, with about 91% rejection of MB even at the end of the 10th cycle, indicating its potential.

The Performance and Mechanism of a Mg-Al Double-Layer Oxide in Chloride ion Removal from an Aqueous Solution

The increasing threat of chloride ions (Cl-) has led researchers to explore efficient removal technologies. Sewage treatment with a double-layer hydroxide/oxide (LDH/LDO) is receiving increasing attention. In this work, Mg-Al LDO adsorbents were produced by the calcination of the Mg-Al LDH precursor, which was constituted by improved coprecipitation. The influence of calcination temperature, calcination time, adsorbent dosage, Cl- initial concentration, contact time, and adsorption temperature on Cl- elimination was investigated systematically. The experimental results showed that a better porous structure endowed the Mg-Al LDO with outstanding adsorption properties for Cl-. The adsorption process was well matched to the pseudo-second-order kinetics model and the Freundlich model. Under optimal conditions, more than 97% of the Cl- could be eliminated. Moreover, the removal efficiency was greater than 90% even after 11 adsorption-desorption cycles. It was found that the electrostatic interaction between Cl- and the positively charged Mg-Al LDO laminate, coupled with the reconstruction of the layer structure, was what dominated the Cl- removal process.

Efficacious bioremediation of heavy metals and radionuclides from wastewater employing aquatic macro- and microphytes

Cytotoxic, mutagenic, and carcinogenic contaminants, such as heavy metals and radionuclides, have become an alarming environmental concern globally, especially for developed and developing nations. Moreover, inefficient prevalent wastewater treatment technologies combined with increased industrial activity and modernization has led to increase in the concentration of toxic metals and radioactive components in the natural water bodies. However, for the improvement of ecosystem of rivers, lakes, and other water sources different physicochemical methods such as membrane filtration, reverse osmosis, activated carbon adsorption, electrocoagulation, and other electrochemical treatment are employed, which are uneconomical and insufficient for the complete abatement of these emerging pollutants. Therefore, the application of bioremediation employing aquatic macrophytes and microphytes have gained considerable importance owing to the benefits of cost-effectiveness, eco-friendly, and higher energy efficiency. Thus, the present review aims to enlighten the readers on the potential application of algae, cyanobacteria, plant, and other aquatic micro- and macrophytes for the elimination of carcinogenic metals and radioactive isotopes from wastewater. Additionally, the use of transgenic plants, genetically modified species, algal-bacterial symbiosis for the enhancement of removal efficiency of mutagenic contaminants are also highlighted. Furthermore, species selection based on robustness, mechanism of different pathways for heavy metal and radionuclide detoxification are elucidated in this review article.

Alginate-based nano-adsorbent materials - Bioinspired solution to mitigate hazardous environmental pollutants

Population growth and industrialization is associated with the elevation of hazardous pollutants, including heavy metals, biomedical wastes, personal-care products, endocrine-disrupters, pharmaceutically active compounds, and colorants in the environment. The scientific focus has been devoted to developing novel adsorbents to mitigate hazardous pollutants by constructing hybrids of different polymers and nano-structured materials for improved workability and physicochemical attributes. Recently, much attention has been devoted to nanomaterials in environmental remediation, owning to their exceptional characteristics including novel electrical/chemical features, quantum size effects, tunable functionalization, high scalability, and surface-area-to-volume ratio. Target-specific designing of nanocomposites impart high functionality. The cost-effective and eco-friendly synthesis of bioadsorbent materials is increasing for the removal of hazardous pollutants. Due to biocompatible, biodegradable, and eco-friendly nature, sodium alginate has been widely reported for the preparation of bioadsorbent materials to remove different inorganic/organic pollutants. In this review, the potentialities of alginate-based nanocomposites have been described for environmental remediation purposes. Different nanomaterials, including silica, metallic oxide, graphene oxide, hybrid inorganic-organic, non-magnetic-magnetic, carbon nanorods, nanotubes, polymeric nanocarriers, and several other materials have been described in combination with alginate biopolymer for environmental remediation.

Polymeric Nanocomposites for Environmental and Industrial Applications

Polymeric nanocomposites (PNC) have an outstanding potential for various applications as the integrated structure of the PNCs exhibits properties that none of its component materials individually possess. Moreover, it is possible to fabricate PNCs into desired shapes and sizes, which would enable controlling their properties, such as their surface area, magnetic behavior, optical properties, and catalytic activity. The low cost and light weight of PNCs have further contributed to their potential in various environmental and industrial applications. Stimuli-responsive nanocomposites are a subgroup of PNCs having a minimum of one promising chemical and physical property that may be controlled by or follow a stimulus response. Such outstanding properties and behaviors have extended the scope of application of these nanocomposites. The present review discusses the various methods of preparation available for PNCs, including in situ synthesis, solution mixing, melt blending, and electrospinning. In addition, various environmental and industrial applications of PNCs, including those in the fields of water treatment, electromagnetic shielding in aerospace applications, sensor devices, and food packaging, are outlined.

A critical review on various remediation approaches for heavy metal contaminants removal from contaminated soils

Heavy metal pollution remains a global environmental challenge that poses a significant threat to human life. Various methods have been explored to eliminate heavy metal pollutants from the environment. However, most methods are constrained by high expenses, processing duration, geological problems, and political issues. The immobilization of metals, phytoextraction, and biological methods have proven practical in treating metal contaminants from the soil. This review focuses on the general status of heavy metal contamination of soils, including the excessive heavy metal concentrations in crops. The assessment of the recent advanced technologies and future challenges were reviewed. Molecular and genetic mechanisms that allow microbes and plants to collect and tolerate heavy metals were elaborated. Tremendous efforts to remediate contaminated soils have generated several challenges, including the need for remediation methodologies, degrees of soil contamination, site conditions, widespread adoptions and various possibilities occurring at different stages of remediation are discussed in detail.

SBA-15 obtained from rice husk ashes wet-impregnated with metals (Al, Co, Ni) as efficient catalysts for 1,4-dihydropyridine three-component reaction

A fully characterized mesoporous silica prepared from industrial waste was impregnated with metals and applied as a green heterogeneous catalyst.

Engineered Nanomaterials in Soil: Their Impact on Soil Microbiome and Plant Health

A staggering number of nanomaterials-based products are being engineered and produced commercially. Many of these engineered nanomaterials (ENMs) are finally disposed into the soil through various routes in enormous quantities. Nanomaterials are also being specially tailored for their use in agriculture as nano-fertilizers, nano-pesticides, and nano-based biosensors, which is leading to their accumulation in the soil. The presence of ENMs considerably affects the soil microbiome, including the abundance and diversity of microbes. In addition, they also influence crucial microbial processes, such as nitrogen fixation, mineralization, and plant growth promoting activities. ENMs conduct in soil is typically dependent on various properties of ENMs and soil. Among nanoparticles, silver and zinc oxide have been extensively prepared and studied owing to their excellent industrial properties and well-known antimicrobial activities. Therefore, at this stage, it is imperative to understand how these ENMs influence the soil microbiome and related processes. These investigations will provide necessary information to regulate the applications of ENMs for sustainable agriculture and may help in increasing agrarian production. Therefore, this review discusses several such issues.