TiO2 nanofiltration membranes prepared by molecular layer deposition for water purification

Incorporation of Ag-ZnO Nanoparticles into PVDF Membrane Formulation to Enhance Dye Retention, Permeability, and Antibacterial Properties

Ultrafiltration is essential for wastewater treatment, but it faces challenges such as selectivity, control, and fouling reduction. Incorporating nanoparticles into membranes enhances retention, boosts permeability, and limits fouling, improving overall performance. This study explores the properties of PVDF/Ag-ZnO composite membranes, highlighting the influence of silver-doped zinc oxide nanoparticles on membrane structure, performance, and antimicrobial effect. The non-solvent-induced phase separation (NIPS) method successfully led to the preparation of composite membranes; this method used different doses of silver-doped zinc oxide (Ag-ZnO) nanoparticles with Poly(vinylidene fluoride) (PVDF). Scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), and water contact angle measurements were used to validate the influence of nanoparticles on the composite membrane (PVDF/Ag-ZnO) structure. Conversely, morphology (porosity, surface rigorosity), hydrophilicity, and permeability were analyzed through contact angle, image analysis, and flux measurement. In addition, the membranes were tested for antimicrobial activity against E. coli. Membrane performance shows that the incorporation of 20% w/w Ag-ZnO resulted in improved water permeability, which was about 2.73 times higher than that of a pure PVDF membrane (192.2 L·m-2·h-1·bar-1). The membrane porosity showed a linear increase with the number of NPs. The resultant asymmetric membrane was altered to increase the number of pores on the top surface by 61% and the cross-sectional pore surface by 663%. Furthermore, a high antibacterial activity of Ag-ZnO 20% was shown.

Ceramic Nanofiltration Membranes: Creating Nanopores by Calcination of Atmospheric-Pressure Molecular Layer Deposition Grown Titanicone Layers

Ceramic membrane technology, whether applied as a stand-alone separation technology or in combination with energy-intensive approaches like distillation, is a promising solution for lower energy alternatives with minimal carbon footprints. To improve the separation of solutes in the nanofiltration range from industrial wastewater streams, ceramic nanofiltration (NF) membranes with reproducible sub-nanometre pore sizes are required. To achieve this, the emerging technique of molecular layer deposition (MLD) is employed to develop ceramic NF membranes, and its efficiency and versatility make it a powerful tool for preparing uniform nanoscale high-porosity membranes. Our work, which involved vapor-phase titanium tetrachloride as a precursor and ethylene glycol as a co-reactant, followed by calcination in air at 350 °C, resulted in NF membranes with pore sizes (radii) around ~0.8 ± 0.1 nm and a demineralized water permeability of 13 ± 1 L·m-2·h-1·bar-1.The high-water flux with >90% rejection of polyethylene glycol molecules with a molecular size larger than 380 ± 6 Dalton indicates the efficiency of the MLD technique in membrane functionalization and size-selective separation processes, and its potential for industrial applications.

Interface Engineering by Molecular Layer Deposition on Polymer Membrane for Selective Ion Transport

Molecular layer deposition (MLD) of ethylene glycol-alucone (EG-alucone) on the Nafion cation exchange membrane is investigated to understand its impact on the morphology of the composite and consequent enhancement of ion transport selectivity. X-ray photoelectron spectroscopy, scanning electron microscopy, Density functional theory, and Doppler broadening positron annihilation spectroscopy are comprehensively employed to examine the morphology of the composite, particularly the engineered interface between EG-alucone and Nafion. These studies reveal the diffusion and subsequent reaction of the Lewis-acidic trimethyl aluminum precursor with the polymer substrate during MLD. The Al─F bond, thus formed, modifies the well-defined microstructures of Nafion and creates a distinct hybrid region with size-based exclusion properties. Post-MLD hydration partially converts the deposited EG-alucone to alumina, reshaping the surface morphology and potentially forming a conformal top layer. The positively charged nature of this top layer, along with the steric sieving effect at the EG-alucone-polymer interface, contribute to the observed improvement in monovalent ion selectivity (Cs+/Na+ = 1.99 ± 0.08 & Cs+/Ba2+ = 1.50 ± 0.05) without significantly compromising membrane conductivity. A three-layer model of the composite membrane, supported by electrochemical impedance spectroscopy and radiotracer-based transport measurements, elucidates the structure-property relationship responsible for the observed selective ion transport.

Carbon-Doped TiO2 Nanofiltration Membranes Prepared by Interfacial Reaction of Glycerol with TiCl4 Vapor

In the pursuit of developing advanced nanofiltration membranes with high permeation flux for organic solvents, a TiO2 nanofilm was synthesized via a vapor-liquid interfacial reaction on a flat-sheet α-Al2O3 ceramic support. This process involves the reaction of glycerol, an organic precursor with a structure featuring 1,2-diol and 1,3-diol groups, with TiCl4 vapor to form organometallic hybrid films. Subsequent calcination in air at 250 °C transforms these hybrid films into carbon-doped titanium oxide nanofilms. The unique structure of glycerol plays a crucial role in determining the properties of the resulting nanopores, which exhibit high solvent permeance and effective solute rejection. The synthesized carbon-doped TiO2 nanofiltration membranes demonstrated impressive performance, achieving a pure methanol permeability as high as 90.9 L·m-2·h -1·bar-1. Moreover, these membranes exhibited a rejection rate of 93.2% for Congo Red in a methanol solution, underscoring their efficacy in separating solutes from solvents. The rigidity of the nanopores within these nanofilms, when supported on ceramic materials, confers high chemical stability even in the presence of polar solvents. This robustness makes the carbon-doped TiO2 nanofilms suitable for applications in the purification and recovery of organic solvents.

Ultra-Stable Inorganic Mesoporous Membranes for Water Purification

Thin, supported inorganic mesoporous membranes are used for the removal of salts, small molecules (PFAS, dyes, and polyanions) and particulate species (oil droplets) from aqueous sources with high flux and selectivity. Nanofiltration membranes can reject simple salts with 80-100% selectivity through a space charge mechanism. Rejection by size selectivity can be near 100% since the membranes can have a very narrow size distribution. Mesoporous membranes have received particular interest due to their (potential) stability under operational conditions and during defouling operations. More recently, membranes with extreme stability became interesting with the advent of in situ fouling mitigation by means of ultrasound emitted from within the membrane structure. For this reason, we explored the stability of available and new membranes with accelerated lifetime tests in aqueous solutions at various temperatures and pH values. Of the available ceria, titania, and magnetite membranes, none were actually stable under all test conditions. In earlier work, it was established that mesoporous alumina membranes have very poor stability. A new nanofiltration membrane was made of cubic zirconia membranes that exhibited near-perfect stability. A new ultrafiltration membrane was made of amorphous silica that was fully stable in ultrapure water at 80 °C. This work provides details of membrane synthesis, stability characterization and data and their interpretation.

Self-cleaning and photodegradle PVDF separation membranes modified with self-assembled TiO2-g-CS/CNTs particle

This work obtained separation membranes with UV-cleaning performance by adding TiO2-g-CS/CNTs photocatalyst to the PVDF. The positively charged chitosan (CS) and negatively charged carboxylic carbon nanotube (CNTs-COOH) can be self-assembled into the bilayer structure on the surface of TiO2 particles through electrostatic attraction. The presence of many hydrophilic groups in CS and CNTs-COOH significantly improves the hydrophilicity of TiO2-g-CS/CNTs-PVDF membrane, and helps TiO2 to be uniformly dispersed on the upper surface. TiO2-g-CS/CNTs promote the change of pore structure and expand the flux of the modified membrane to 4.5 times that of pure PVDF. Zeta potential demonstrates that the TiO2-g-CS particles successfully attracted CNTs in the PVDF matrix, and the membrane surface was still positively charged. Thus, the combined effect of the positively charged TiO2-g-CS and the highly adsorbed CNTs enhanced the retention of the contaminants. More importantly, there is a charge transfer between the grafted CS and TiO2 interface to obtain a broader light absorption band. The excitation carriers provided by CNTs significantly contribute to the photocatalytic performance after transfer between TiO2 and CS; thus, TiO2-g-CS/CNTs-PVDF produces higher photocatalytic activity for dye molecules (degradation rate > 97 %).

Ceramic thin-film composite membranes with tunable subnanometer pores for molecular sieving

Ceramic membranes are a promising alternative to polymeric membranes for selective separations, given their ability to operate under harsh chemical conditions. However, current fabrication technologies fail to construct ceramic membranes suitable for selective molecular separations. Herein, we demonstrate a molecular-level design of ceramic thin-film composite membranes with tunable subnanometer pores for precise molecular sieving. Through burning off the distributed carbonaceous species of varied dimensions within hybrid aluminum oxide films, we created membranes with tunable molecular sieving. Specifically, the membranes created with methanol showed exceptional selectivity toward monovalent and divalent salts. We attribute this observed selectivity to the dehydration of the large divalent ions within the subnanometer pores. As a comparison, smaller monovalent ions can rapidly permeate with an intact hydration shell. Lastly, the flux of neutral solutes through each fabricated aluminum oxide membrane was measured for the demonstration of tunable separation capability. Overall, our work provides the scientific basis for the design of ceramic membranes with subnanometer pores for molecular sieving using atomic layer deposition.

Poloxamer 407 Combined with Polyvinylpyrrolidone To Prepare a High-Performance Poly(ether sulfone) Ultrafiltration Membrane

At present, the design and fabrication of polymer membranes with high permeability and good retention ability are still huge challenges. In this study, the commercial Poloxamer 407 (Pluronic F127) is selected as a multifunctional additive, and polyvinylpyrrolidone is used as a pore-forming agent to modify the poly(ether sulfone) membrane by liquid-liquid phase conversion technology to prepare an ultrafiltration membrane with excellent performance. The hydrophobic poly(propylene oxide) segment in Poloxamer 407 guarantees that this copolymer can be firmly anchored to the poly(ether sulfone) matrix, and the hydrophilic poly(ethylene oxide) segments in Poloxamer 407 impart a stronger hydrophilic nature to the modified membrane surface. Therefore, the permeability and hydrophilicity of the modified membrane are significantly improved and the modified membrane also has good stability. When the amount of Poloxamer 407 added to the casting solution reached 0.6 g, the water flux of the modified membrane was as high as 368 L m-2 h-1, and the rejection rate of bovine serum albumin was close to 98%. In the test to isolate organic small molecule dyes, the retention rate of the modified membrane to Congo red is 94.27%. In addition, the modified membrane shows an excellent water flux recovery rate and antifouling ability. It performs well in subsequent cycle tests and long-term membrane life tests and can be used repeatedly. Our work has resulted in poly(ether sulfone) membranes with good performance, which show great potential in the treatment of biomedical wastewater and the removal of industrial organic dye wastewater, it provides ideas for the development and application of amphiphilic polymer materials.

Carbon-doped metal oxide interfacial nanofilms for ultrafast and precise separation of molecules

Membranes with molecular-sized, high-density nanopores, which are stable under industrially relevant conditions, are needed to decrease energy consumption for separations. Interfacial polymerization has demonstrated its potential for large-scale production of organic membranes, such as polyamide desalination membranes. We report an analogous ultrafast interfacial process to generate inorganic, nanoporous carbon-doped metal oxide (CDTO) nanofilms for precise molecular separation. For a given pore size, these nanofilms have 2 to 10 times higher pore density (assuming the same tortuosity) than reported and commercial organic solvent nanofiltration membranes, yielding ultra-high solvent permeance, even if they are thicker. Owing to exceptional mechanical, chemical, and thermal stabilities, CDTO nanofilms with designable, rigid nanopores exhibited long-term stable and efficient organic separation under harsh conditions.

Membrane Fabrication and Modification by Atomic Layer Deposition: Processes and Applications in Water Treatment and Gas Separation

Membrane-based separation processes are part of most water purification plants worldwide. Industrial separation applications, primarily water purification and gas separation, can be improved with novel membranes or modification to existing ones. Atomic layer deposition (ALD) is an emerging technique that is proposed to upgrade certain kinds of membranes independent of their chemistry and morphology. ALD deposits thin, defect-free, angstrom-scale, and uniform coating layers on a substrate's surface by reacting with gaseous precursors. The surface-modifying effects of ALD are described in the present review, followed by a description of various types of inorganic and organic barrier films and how these can be used in combination with ALD. The role of ALD in membrane fabrication and modification is categorized into different membrane-based groups according to the treated medium, i.e., water or gas. In all membrane types, the ALD-based direct deposition of inorganic materials, mainly metal oxides, on the membrane surface can improve antifouling, selectivity, permeability, and hydrophilicity. Therefore, the ALD technique can broaden the applications of membranes to the treatment of emerging contaminants in water and air. Finally, the advancement, limitations, and challenges of ALD-based membrane fabrication and modification are compared to provide a comprehensive guideline for developing next-generation membranes with improved filtration and separation performance.

Polymeric membranes functionalized with nanomaterials (MP@NMs): A review of advances in pesticide removal

The excessive contamination of drinking water sources by pesticides has a pernicious impact on human health and the environment since only 0.1% of pesticides is utilized effectively to control the and the rest is deposited in the environment. Filtration by polymeric membranes has become a promising technique to deal with this problem; however, the scientific community, in the need to find better pesticide retention results, has begun to meddle in the functionalization of polymeric membranes. Given the great variety of membrane, polymer, and nanomaterial synthesis methods present in the market, the possibilities of obtaining membranes that adjust to different variables and characteristics related to a certain pesticide are relatively extensive, so it is expected that this technology will represent one of the main pesticide removal strategies in the future. In this direction, this review focused on, - the main characteristics of the nanomaterials and their impact on pristine polymeric membranes; - the removal performance of functionalized membranes; and - the main mechanisms by which membranes can retain pesticides. Based on these insights, the functionalized polymeric membranes can be considered as a promising technology in the removal of pesticides since the removal performance of this technology against pesticide showed a significant increase. Obtaining membranes that adjust to different variables and characteristics related to a certain pesticide are relatively extensive, so it is expected that functionalized membrane technology will represent one of the main pesticide removal strategies in the future.

Cross-Linked Networks of 1,6-Hexanedithiol with Gold Nanoparticles to Improve Permeation Flux of Polyethersulfone Membrane

It is a great challenge to design and prepare polymeric membranes with excellent permeability and good rejection. In this study, a modifier of gold nanoparticles for crosslinking and self-assembly by 1,6-hexanedithiol is fabricated and used to modify the polyethersulfone membrane as an additive, which forms a uniform porous membrane by liquid-liquid phase conversion technology. The morphology of the membrane is investigated by scanning electron microscopy (SEM), the change of the hydrophilicity of the membrane surface after modification is measured by the contact angle goniometer, and the performance of the fabricated membrane is measured by evaluating the pure water flux and the rejection ratio of bovine serum albumin. The results indicate that the permeability of the modified membrane has a significant improvement. When the mass fraction of the modifying agent is 5 wt%, the water flux of the modified membrane reaches up to 131.6 L m^-2 h^-1, and has a good rejection ratio to bovine serum albumin. In short, this work plays an important role in improving the flux of the membrane and maintaining good separation performance.

Role of titanium and organic precursors in molecular layer deposition of "titanicone" hybrid materials

The development of hybrid inorganic-organic films with well-controlled properties is important for many applications. Molecular layer deposition (MLD) allows the deposition of these hybrid films using sequential, self-limiting reactions, similar to atomic layer deposition (ALD). In this paper, we use first principles density functional theory (DFT) to investigate the growth mechanism of titanium-containing hybrid organic-inorganic MLD films, known as "titanicones". We investigate in detail the chemistry between the most common Ti precursors, namely titanium tetrachloride (TiCl₄) and tetrakis(dimethylamido)titanium (Ti(DMA)₄), and ethylene glycol (EG) and glycerol (GL) as the organic precursors. We analyse the impact of the substrate on the initial MLD reactions in titanicone film growth using three different surface models: anatase TiO₂, rutile TiO₂ and Al₂O₃. Calculated energetics show that while TiCl₄ is reactive towards the anatase and rutile TiO₂ surfaces, it is not reactive towards the Al₂O₃ surface. Ti(DMA)₄ is reactive towards all surfaces. This is attributed to the stronger Ti-Cl bonds in TiCl₄ compared to Ti-N bonds in Ti(DMA)₄. Ti(DMA)₄ also shows high reactivity to the organics compared to TiCl₄. Double reactions of EG and GL with the TiCl₃ species from TiCl₄ and TiDMA species from Ti(DMA)₄ are also explored to better understand the origin of the different thicknesses of EG-titanicone and GL-titanicone films observed in experimental work. We find that EG and GL coupled with TiCl₄ can orient in a flat lying configuration on anatase while on rutile, the preferred orientation is upright. When combined with Ti(DMA)₄, EG and GL prefer the flat lying configuration on all surfaces. This work shows that the choice of the surface and the metallic precursor has a major impact on the behaviour of organic species. DFT findings provide motivation to develop a low temperature rutile TiO₂/titanicone film suggesting that the desired film growth could be achieved.

Polyelectrolytes as Building Blocks for Next-Generation Membranes with Advanced Functionalities

The global society is in a transition, where dealing with climate change and water scarcity are important challenges. More efficient separations of chemical species are essential to reduce energy consumption and to provide more reliable access to clean water. Here, membranes with advanced functionalities that go beyond standard separation properties can play a key role. This includes relevant functionalities, such as stimuli-responsiveness, fouling control, stability, specific selectivity, sustainability, and antimicrobial activity. Polyelectrolytes and their complexes are an especially promising system to provide advanced membrane functionalities. Here, we have reviewed recent work where advanced membrane properties stem directly from the material properties provided by polyelectrolytes. This work highlights the versatility of polyelectrolyte-based membrane modifications, where polyelectrolytes are not only applied as single layers, including brushes, but also as more complex polyelectrolyte multilayers on both porous membrane supports and dense membranes. Moreover, free-standing membranes can also be produced completely from aqueous polyelectrolyte solutions allowing much more sustainable approaches to membrane fabrication. The Review demonstrates the promise that polyelectrolytes and their complexes hold for next-generation membranes with advanced properties, while it also provides a clear outlook on the future of this promising field.

Preparation of Ordered Anodic Porous Alumina with Single-Nanometer-Order-Size Holes by Atomic Layer Deposition

Ordered anodic porous alumina with controlled-size holes on the order of a single-nanometer scale was obtained by the atomic layer deposition (ALD) of Al₂O₃ or TiO₂. The thin metal oxide layers of uniform thickness were formed successfully on the inner wall of the hole of the ordered anodic porous alumina with high aspect ratios by ALD. The hole diameter of the ordered anodic porous alumina could be controlled precisely by adjusting the number of cycles of ALD. The obtained anodic porous alumina with an ordered hole arrangement of reduced holes will be applied to various application fields requiring uniform-sized holes on the order of a single-nanometer scale, such as the starting material for preparing various types of quantum effect devices.

The Perspective and Challenge of Nanomaterials in Oil and Gas Wastewater Treatment

Oil and gas wastewater refers to the waste stream produced in special production activities such as drilling and fracturing. This kind of wastewater has the following characteristics: high salinity, high chromaticity, toxic and harmful substances, poor biodegradability, and a difficulty to treat. Interestingly, nanomaterials show great potential in water treatment technology because of their small size, large surface area, and high surface energy. When nanotechnology is combined with membrane treatment materials, nanofiber membranes with a controllable pore size and high porosity can be prepared, which provides more possibilities for oil–water separation. In this review, the important applications of nanomaterials in wastewater treatment, including membrane separation technology and photocatalysis technology, are summarized. Membrane separation technology is mainly manifested in ultrafiltration (UF), nanofiltration (NF), and reverse osmosis (RO). It also focuses on the application of semiconductor photocatalysis technology induced by TiO₂ in the degradation of oil and gas wastewater. Finally, the development trends of nanomaterials in oil and gas wastewater treatment are prospected.

Nanoparticles functionalized ceramic membranes: fabrication, surface modification, and performance

Membrane technologies are used intensively for desalination and wastewater treatment. Water filtration using ceramic membranes exhibited high performance compared with polymeric membranes due to various properties such as high resistance to fouling, permeability, rejection rate, and chemical stability. Recently, the performance of nanocomposite ceramic membranes was improved due to the development in nanotechnology. This article focusses on the development of porous ceramic membranes and nanomaterial functionalized ceramic membranes for water filtration applications. At the beginning, various fabrication methods of ceramic membranes were described, and the effect of surface modification techniques on the membrane intrinsic properties was reviewed. Then, the performance of nanoparticles functionalized ceramic membranes was evaluated in terms of physicochemical properties, rejection rate, and water permeability. This work can help new entrants and established researchers to become familiar with the current challenges and developments of nanoparticle-incorporated ceramic membranes for water filtration applications.

Runge-Kutta Numerical Method Followed by Richardson's Extrapolation for Efficient Ion Rejection Reassessment of a Novel Defect-Free Synthesized Nanofiltration Membrane

A defect-free, loose, and strong layer consisting of zirconium (Zr) nanoparticles (NPs) has been successfully established on a polyacrylonitrile (PAN) ultrafiltration substrate by an in-situ formation process. The resulting organic–inorganic nanofiltration (NF) membrane, NF-PANZr, has been accurately characterized not only with regard to its properties but also its structure by the atomic force microscopy, field emission scanning electron microscopy, and energy dispersive spectroscopy. A sophisticated computing model consisting of the Runge–Kutta method followed by Richardson extrapolation was applied in this investigation to solve the extended Nernst–Planck equations, which govern the solute particles’ transport across the active layer of NF-PANZr. A smart, adaptive step-size routine is chosen for this simple and robust method, also known as RK4 (fourth-order Runge–Kutta). The NF-PANZr membrane was less performant toward monovalent ions, and its rejection rate for multivalent ions reached 99.3%. The water flux of the NF-PANZr membrane was as high as 58 L · m⁻² · h⁻¹. Richardson’s extrapolation was then used to get a better approximation of Cl⁻ and Mg²⁺ rejection, the relative errors were, respectively, 0.09% and 0.01% for Cl⁻ and Mg²⁺. While waiting for the rise and expansion of machine learning in the prediction of rejection performance, we strongly recommend the development of better NF models and further validation of existing ones.

Euler’s Numerical Method for Ions Rejection Reassessment of a Defect-Free Synthesized Nanofiltration Membrane with Ultrathin Titania Film as the Selective Layer

Titanium (Ti) nanoparticles (NPs) were successfully seeded on the platform of a polyacrylonitrile (PAN) ultrafiltration (UF) membrane previously coated with bio-glue (a co-deposition of dopamine hydrochloric bicarbonate buffer having undergone pyrocatechol deprotonation). The tools in vogue, especially field emission scanning electron microscopy (FESEM), energy dispersive spectroscopy (EDS), and atomic force microscopy (AFM), have made it possible to fully characterize the structure of the new organic-inorganic nanofiltration (NF) membrane, namely NF_PAN_Ti. A soft computing model has been applied to make commonplace the complex and implicit extended Nernst–Planck equations that govern the transport of ions through NF membranes. Euler’s numerical method was applied with a small step-size and the results obtained were very interesting. The filtration velocity approach of GUEROUT-ELFORD-FERRY helped to estimate the average pore size of NF_PAN_Ti to rp = 0.538 nm. A six-day test carried out on NF_PAN_Ti demonstrated its long-term stability and showed a steady-rejection rate of 89.3% of MgCl2 salt and permeate flux of 56 L·m−2·h−1. The Euler’ numerical method corroborated perfectly the experimental findings since the relative error was found to be very low at 0.33% for Cl− and 0.09% for Mg2+ (RE << 0.1). These practical prediction tools may henceforth help in the choice and calibration of next-generation NF membranes’ synthesis.

Tuning the Ion-Selectivity of Thin-Film Composite Nanofiltration Membranes by Molecular Layer Deposition of Alucone

This work addresses a key challenge of tailoring the ion selectivity of a thin-film composite nanofiltration membrane to a specific application, such as water softening, without altering the water permeability. We modified the active surface of a commercial NF270 membrane by molecular layer deposition (MLD) of ethylene glycol-Al (EG-alucone). With increasing deposition cycles, we found that the MLD precursors first infiltrated and deposited in the active layer of NF270, then inflated the active layer, and finally deposited on the surface as a distinct EG-alucone layer. The deposition process changed the morphology of the membrane active layer and decreased the overall density of its fixed negative charge by embedding the positively charged EG-alucone. Filtration experiments revealed that these modifications affected the ion separation properties of the membrane without significantly hindering the water permeability. Specifically, the permeation of Na⁺ increased relative to that of Mg²⁺, as indicated by the permselectivity of Na⁺ salts over Mg²⁺ salts. The changes in permselectivities with an increasing number of MLD cycles were rationalized using the dielectric, steric, and electrostatic ion exclusion mechanisms, which are related to the membrane material, pore size, and fixed charge, respectively. These relations open a path for the rational design of nanofiltration membranes with tailored selectivity by tuning the properties of the MLD layer. Filtration results of natural brackish groundwater using the MLD modified membranes agreed with the single salt experiments. As a result, water hardness was 26% lower for the permeate obtained using the MLD-modified membranes, which were found stable even during a 24 h filtration run. These results highlight the practical potential of this approach in enhancing water softening efficiency.

The toolbox of porous anodic aluminum oxide–based nanocomposites: from preparation to application

Anodic aluminum oxide (AAO) templates have been intensively investigated during the past decades and have meanwhile been widely applied through both sacrificial and non-sacrificial pathways. In numerous non-sacrificial applications, the AAO membrane is maintained as part of the obtained composite materials; hence, the template structure and topography determine to a great extent the potential applications. Through-hole isotropic AAO features nanochannels that promote transfer of matter, while anisotropic AAO with barrier layer exhibits nanocavities suitable as independent and homogenous containers. By combining the two kinds of AAO membranes with diverse organic and inorganic materials through physical interactions or chemical bonds, AAO composites are designed and applied in versatile fields such as catalysis, drug release platform, separation membrane, optical appliances, sensors, cell culture, energy, and electronic devices. Therefore, within this review, a perspective on exhilarating prospect for complementary advancement on AAO composites both in preparation and application is provided.

First principles study of reactions in alucone growth: the role of the organic precursor

Organic-inorganic hybrid materials are a unique class of materials with properties driven by the organic and inorganic components, making them useful for flexible devices. Molecular layer deposition (MLD) offers novel pathways for the fabrication of such hybrids by using inorganic metal precursors and the vast range of organic molecules with tunable properties. To investigate and understand the mechanism of growth a combination of theoretical and experimental data is needed. In this contribution, we present a first principles investigation of the molecular mechanism of the growth of hybrid organic-inorganic thin films of aluminium alkoxides, known as "alucones" grown by MLD. We explore the interactions between precursors by analyzing the MLD reaction products of the alumina surface terminated with Al(CH3) groups after the trimethyl aluminium pulse; this yields monomethyl-Al2O3 (Al-CH3-Al2O3) and dimethyl-Al2O3 (Al(CH3)2-Al2O3) terminated surfaces. The organic precursors are ethylene glycol (EG), diethylene glycol (DEG), triethylene glycol (TEG) and tetraethylene glycol (FEG). A detailed comparison with alucones grown with ethylene glycol (EG) and glycerol (GL) precursors is presented to assist the interpretation of experimental findings regarding the differences in the hybrid films grown by EG and GL. The results show that Al-O formation with release of methane is favorable for all precursors. EG and GL can lie flat and create so-called double reactions through the reaction of the two terminal hydroxyl groups with the surface fragments. This phenomenon removes active hydroxyl sites for EG. However, for GL the third hydroxyl group is available and growth can proceed. This analysis shows the origin of differences in thickness of alucones found for EG and GL.

Ceramic nanocomposite membranes and membrane fouling: A review

Membrane technologies have broad applications in the removal of contaminants from drinking water and wastewater. In recent decades, ceramic membrane has made rapid progress in industrial/municipal wastewater treatment and drinking water treatment owing to their advantageous properties over conventional polymeric membrane. The beneficial characteristics of ceramic membranes include fouling resistance, high permeability, good recoverability, chemical stability, and long life time, which have found applications with the recent innovations in both fabrication methods and nanotechnology. Therefore, ceramic membranes hold great promise for potential applications in water treatment. This paper mainly reviews the progress in the research and development of ceramic membranes, with key focus on porous ceramic membranes and nanomaterial-functionalized ceramic membranes for nanofiltration or catalysis. The current state of the available ceramic membranes in industry and academia, and their potential advantages, limitations and applications are reviewed. The last section of the review focuses on ceramic membrane fouling and the efforts towards ceramic membrane fouling mitigation. The advances in ceramic membrane technologies have rarely been widely reviewed before, therefore, this review could be served as a guide for the new entrants to the field, as well to the established researchers.

Antimicrobial Bilayer Nanocomposites Based on the Incorporation of As-Synthetized Hollow Zinc Oxide Nanotubes

An antimicrobial polymeric bilayer structure based on the application of an acrylic coating containing hollow zinc oxide nanotubes over a polymeric substrate was developed in this work. Firstly, zinc oxide nanotubes (ZnO_NT) were obtained by an atomic layer deposition (ALD) process over electrospun polyvinyl alcohol nanofibers followed by polymer removal through calcination with the purpose of obtaining antimicrobial nanostructures with a high specific area. Parameters of electrospinning, ALD, and calcination processes were set in order to obtain successfully hollow zinc oxide nanotubes. Morphological studies through scanning electron microscopy (SEM) and transmission electron microscopy (TEM) microscopies confirmed the morphological structure of ZnO_NT with an average diameter of 180 nm and thickness of approximately 60 nm. Thermal and X-ray diffraction (XRD) analyses provided evidence that calcination completely removed the polymer, resulting in a crystalline hexagonal wurtzite structure. Subsequently, ZnO_NT were incorporated into a polymeric coating over a polyethylene extruded film at two concentrations: 0.5 and 1 wt. % with respect to the polymer weight. An antimicrobial analysis of developed antimicrobial materials was performed following JIS Z2801 against Staphylococcus aureus and Escherichia coli. When compared to active materials containing commercial ZnO nanoparticles, materials containing ZnO_NT presented higher microbial inhibition principally against Gram-negative bacteria, whose reduction was total for films containing 1 wt. % ZnO_NT. Antiviral studies were also performed, but these materials did not present significant viral reduction.

ZnO Microfiltration Membranes for Desalination by a Vacuum Flow-Through Evaporation Method

ZnO was deposited on macroporous α-alumina membranes via atomic layer deposition (ALD) to improve water flux by increasing their hydrophilicity and reducing mass transfer resistance through membrane pore channels. The deposition of ZnO was systemically performed for 4-128 cycles of ALD at 170 °C. Analysis of membrane surface by contact angles (CA) measurements revealed that the hydrophilicity of the ZnO ALD membrane was enhanced with increasing the number of ALD cycles. It was observed that a vacuum-assisted 'flow-through' evaporation method had significantly higher efficacy in comparison to conventional desalination methods. By using the vacuum-assisted 'flow-through' technique, the water flux of the ZnO ALD membrane (~170 L m^-2 h^-1) was obtained, which is higher than uncoated pristine membranes (92 L m^-2 h^-1). It was also found that ZnO ALD membranes substantially improved water flux while keeping excellent salt rejection rate (>99.9%). Ultrasonic membrane cleaning had considerable effect on reducing the membrane fouling.

Fundamental fouling mechanisms of dissolved organic matter fractions and their implications on the surface modifications of ceramic nanofiltration membranes: insights from a laboratory scale application

This work reports on the fundamental factors influencing inter-foulant and foulant-membrane interactions during simulated dissolved organic matter removal using ceramic nanofiltration. Fouling tests were performed using sodium alginate (SAL), humic acid (HA) and bovine serum albumin (BSA) as model foulants. Fouling potentials of each foulant and their mixtures were investigated using feed solutions containing fixed concentrations of K⁺, Na⁺, Mg²⁺ and Ca²⁺ with a total ionic strength of 10 mM. The impact of modification by atomic layer deposition on fouling mitigation was also assessed. The flux decline in the first 100 min for single foulants was 4.16 × 10^-2, 2.69 × 10^-2 and 1.60 × 10^-2 Lm^-2 for SAL, HA and BSA, respectively. These results demonstrated that for the single foulants, deposition on the membrane surface in the early stages of filtration was primarily governed by membrane-foulant interactions. Interestingly, cake filtration was the least fouling mechanism in feed solutions composed of BSA and SAL (R² = 0.519, 0.374 for BSA + SAL and BSA + SAL + HA, respectively) and the most favorable fouling mechanism of feed solution which included HA and SAL (R² = 0.972). The water contact angle dropped from 58^o to 35° after coating, thus improving its anti-fouling properties.

Novel Submerged Photocatalytic Membrane Reactor for Treatment of Olive Mill Wastewaters

A new hybrid photocatalytic membrane reactor that can easily be scaled-up was designed, assembled and used to test photocatalytic membranes developed using the sol–gel technique. Extremely high removals of total suspended solids, chemical oxygen demand, total organic carbon, phenolic and volatile compounds were obtained when the hybrid photocatalytic membrane reactor was used to treat olive mill wastewaters. The submerged photocatalytic membrane reactor proposed and the modified membranes represent a step forward towards the development of new advanced treatment technology able to cope with several water and wastewater contaminants.

Ultrasound Assisted Synthesis of Size-Controlled Aqueous Colloids for the Fabrication of Nanoporous Zirconia Membrane

Permeation and separation efficiency of ceramic membranes are strongly dependent on their nanoporous structures, especially on the pore size. In this work, ultrasound is employed to form the size-controlled ZrO2 nanoparticles, and a ceramic membrane is prepared with tunable pore size. Under the ultrasound treatment, H+ from water plays a key role in the synthesis process. The cavitation caused by ultrasound promotes the hydrolysis of the precursor in water, which produces a large number of H+. These H+ will react with precipitant added and generate cyclic tetrameric units. Excess H+ can peptize cyclic tetrameric units and form an electrical double layer, resulting in a stable sol. Unlike ultrasound treatment, precipitant will react directly with the precursor and generate precipitation if there is no ultrasound added. Moreover, cavitation is good for the dispersion of cyclic tetrameric units. The particle size of Zr-based colloidal sol can be tuned in the ranges of 1.5 to 120 nm by altering the molar ratio of precursor to precipitant, ultrasonic power density and radiation time. Meanwhile, ultrasonic power density and radiation time have effects on grain size and the crystalline transition temperature of particles which influence performance of the ceramic membrane. As a result, membranes exhibit high performance together with high permeability and desirable rejection. To develop such a simple and controllable method for tuning particle size is extremely important in the preparation of nanoporous ceramic membranes.

On the transformation of "zincone"-like into porous ZnO thin films from sub-saturated plasma enhanced atomic layer deposition

The synthesis of nanoporous ZnO thin films is achieved through annealing of zinc-alkoxide ("zincone"-like) layers obtained by plasma-enhanced atomic layer deposition (PE-ALD). The zincone-like layers are deposited through sub-saturated PE-ALD adopting diethylzinc and O₂ plasma with doses below self-limiting values. Nanoporous ZnO thin films were subsequently obtained by calcination of the zincone-like layers between 100-600 °C. Spectroscopic ellipsometry (SE) and X-ray diffraction (XRD) were adopted in situ during calcination to investigate the removal of carbon impurities, development of controlled porosity, and formation and growth of ZnO crystallites. The layers developed controlled nanoporosity in the range of 1-5%, with pore sizes between 0.27 and 2.00 nm as measured with ellipsometric porosimetry (EP), as a function of the plasma dose and post-annealing temperature. Moreover, the crystallinity and crystallite orientation could be tuned, ranging from a powder-like to a (100) preferential growth in the out-of-plane direction, as measured by synchrotron-radiation grazing incidence XRD. Calcination temperature ranges were identified in which pore formation and subsequent crystal growth occurred, giving insights in the manufacturing of nanoporous ZnO from Zn-based hybrid materials.

Mesoporous ZnO thin films obtained from molecular layer deposited “zincones”

The synthesis of MLD-derived mesoporous ZnO with 20% of porosity is demonstrated and studied by advanced in situ characterization techniques.

Atomic layer deposition for membrane interface engineering

In many applications, interfaces govern the performance of membranes. Structure, chemistry, electrostatics, and other properties of interfaces can dominate the selectivity, flux, fouling resistance, and other critical aspects of membrane functionality. Control over membrane interfacial properties, therefore, is a powerful means of tailoring performance. In this Minireview, we discuss the application of atomic layer deposition (ALD) and related techniques in the design of novel membrane interfaces. We discuss recent literature in which ALD is used to (1) modify the surface chemistry and interfacial properties of membranes, (2) tailor the pore sizes and separation characteristics of membranes, and (3) enable novel advanced functional membranes.

Molecular Layer Deposition-Modified 5A Zeolite for Highly Efficient CO2 Capture

Effective pore mouth size of 5A zeolite was engineered by depositing an ultrathin layer of microporous TiO₂ on its external surface and appropriate pore misalignment at the interface. As a result, a slightly bigger N₂ molecule (kinetic diameter: 0.364 nm) was effectively excluded, whereas CO₂ (kinetic diameter: 0.33 nm) adsorption was only influenced slightly. The prepared composite zeolite sorbents showed an ideal CO₂/N₂ adsorption selectivity as high as ∼70, a 4-fold increase over uncoated zeolite sorbents, while maintaining a high CO₂ adsorption capacity (1.62 mmol/g at 0.5 bar and 25 °C) and a fast CO₂ adsorption rate.

Modification of the Selectivity Properties of Tubular Ceramic Membranes after Alkaline Treatment

This work focuses on the selectivity modification of ceramic membranes after a mild alkaline treatment. Filtration of pure salt-water solutions was carried out with commercial titania membranes before and after the treatment. After treatment, the rejection of NaF significantly decreased, while the rejection of NaCl and NaBr increased. Additionally, NaI and Na₂SO₄ remained close to zero. Pore size and electrical charge being almost unchanged, only significant modifications in the dielectric effects can explain this modification of selectivity. Therefore, the surface chemistry and the interaction (nature and magnitude) with the solvent and with the species present in the solution appear to be modified by the alkaline treatment. This trend is also illustrated by discussing the electric and the dielectric properties that were numerically identified before and after treatment. The alkaline treatment significantly decreased the apparent dielectric constant of NaCl-water solution in the pore, highlighting the rejection of sodium chloride. Contrariwise, the modification of the surface chemistry increased the apparent dielectric constant of NaF-water solution by promoting fluoride transmission.