Peroxymonosulfate-based cleaning technology for metal oxide-coated ceramic ultrafiltration membrane polluted by Alcian Blue 8GX dye: Radical and non-radical oxidation cleaning mechanism

Development of inorganic and mixed matrix membranes for application in toxic dyes-contaminated industrial effluents with in-situ treatments

Dyes are the most ubiquitous organic pollutants in industrial effluents. They are highly toxic to both plants and animals; thus, their removal is paramount to the sustainability of ecosystem. However, they have shown resistance to photolysis and various biological, physical, and chemical wastewater remediation processes. Membrane removal technology has been vital for the filtration/separation of the dyes. In comparison to polymeric membranes, inorganic and mixed matrix (MM) membranes have shown potentials to the removal of dyes. The inorganic and MM membranes are particularly effective due to their high porosity, enhanced stability, improved permeability, higher enhanced selectivity and good stability and resistance to harsh chemical and thermal conditions. They have shown prospects in filtration/separation, adsorption, and catalytic degradation of the dyes. This review highlighted the advantages of the inorganic and MM membranes for the various removal techniques for the treatments of the dyes. Methods for the membranes production have been reviewed. Their application for the filtration/separation and adsorption have been critically analyzed. Their application as support for advanced oxidation processes such as persulfate, photo-Fenton and photocatalytic degradations have been highlighted. The mechanisms underscoring the efficiency of the processes have been cited. Lastly, comments were given on the prospects and challenges of both inorganic and MM membranes towards removal of the dyes from industrial effluents.

Tempospatially Confined Catalytic Membranes for Advanced Water Remediation

The application of homogeneous catalysts in water remediation is limited by their excessive chemical and energy input, weak regenerability, and potential leaching. Heterogeneous catalytic membranes (CMs) offer a new approach to facilitate efficient, selective, and continuous pollutant degradation. Thus, integrating membranes and continuous filtration with heterogeneous advanced oxidation processes (AOPs) can promote thermodynamic and kinetic mass transfers in spatially confined intrapores and facilitate diffusion-reaction processes. Despite the remarkable advantages of heterogeneous CMs, their engineering application is practically restricted due to the fuzzy design criteria for specific applications. Herein, the recent advances in CMs for advanced water remediation are critically reviewed and the design flow for tempospatially confined CMs is proposed. Further, state-of-the-art CM materials and their catalytic mechanisms are reviewed, after which the tempospatial confinement mechanisms comprising the nanoconfinement effect, interface effect, and kinetic mass transfer are emphasized, thus clarifying their roles in the construction and performance optimization of CMs. Additionally, the fabrication methods for CMs based on their catalysts and pore sizes are summarized and an overview of their application and performance evaluations is presented. Finally, future directions for CMs in materials research and water treatment, are presented.

Size-Dependent Catalysis in Fenton-like Chemistry: From Nanoparticles to Single Atoms

State-of-the-art Fenton-like reactions are crucial in advanced oxidation processes (AOPs) for water purification. This review explores the latest advancements in heterogeneous metal-based catalysts within AOPs, covering nanoparticles (NPs), single-atom catalysts (SACs), and ultra-small atom clusters. A distinct connection between the physical properties of these catalysts, such as size, degree of unsaturation, electronic structure, and oxidation state, and their impacts on catalytic behavior and efficacy in Fenton-like reactions. In-depth comparative analysis of metal NPs and SACs is conducted focusing on how particle size variations and metal-support interactions affect oxidation species and pathways. The review highlights the cutting-edge characterization techniques and theoretical calculations, indispensable for deciphering the complex electronic and structural characteristics of active sites in downsized metal particles. Additionally, the review underscores innovative strategies for immobilizing these catalysts onto membrane surfaces, offering a solution to the inherent challenges of powdered catalysts. Recent advances in pilot-scale or engineering applications of Fenton-like-based devices are also summarized for the first time. The paper concludes by charting new research directions, emphasizing advanced catalyst design, precise identification of reactive oxygen species, and in-depth mechanistic studies. These efforts aim to enhance the application potential of nanotechnology-based AOPs in real-world wastewater treatment.

Chalcopyrite functionalized ceramic membrane for micropollutants removal and membrane fouling control via peroxymonosulfate activation: The synergy of nanoconfinement effect and interface interaction

This work developed a novel chalcopyrite (CuFeS2) incorporated catalytic ceramic membrane (CFSCM), and comprehensively evaluated the oxidation-filtration efficiency and mechanism of CFSCM/peroxymonosulfate (PMS) for organics removal and membrane fouling mitigation. Results showed that PMS activation was more efficient in the confined membrane pore structure. The CFSCM50/PMS filtration achieved almost complete removal of 4-Hydroxybenzoic acid (4-HBA) under the following conditions: pH = 6.0, CPMS = 0.5 mM, and C4-HBA = 10 mg/L. Meanwhile, the membrane showed good stability after multiple uses. During the reaction, SO4•- and •OH were generated in the CFSCM50/PMS system, and SO4•- was considered to be the dominant reactive species for pollutant removal. The roles of copper, iron, and sulfur species, as well as the possible catalytic mechanism were also clarified. Besides, the CFSCM50/PMS catalytic filtration exhibited excellent antifouling properties against NOM with reduced reversible and irreversible fouling resistances. The Extended Derjaguin-Landau-Verwey-Overbeek (XDLVO) theory analysis showed an increased in repulsive energy at the membrane-foulant interface in the CFSCM50/PMS system. Membrane fouling model analysis indicated that standard blocking was the dominant fouling pattern for CFSCM50/PMS filtration. Overall, this work demonstrates an efficient catalytic filtration process for foulants removal and outlines the synergy of catalytic oxidation and interface interaction.

Preparation, performance and mechanism of metal oxide modified catalytic ceramic membranes for wastewater treatment

Catalytic ceramic membranes (CMs) integrated with different metal oxides were designed and fabricated by an impregnation-sintering method. The characterization results indicated that the metal oxides (Co₃O₄, MnO₂, Fe₂O₃ and CuO) were uniformly anchored around the Al₂O₃ particles of the membrane basal materials, which could provide a large number of active sites throughout the membrane for the activation of peroxymonosulfate (PMS). The performance of the CMs/PMS system was evaluated by filtrating a phenol solution under different operating conditions. All the four catalytic CMs showed desirable phenol removal efficiency and the performance was in order of CoCM, MnCM, FeCM and CuCM. Moreover, the low metal ion leaching and high catalytic activity even after the 6th run revealed the good stability and reusability of the catalytic CMs. Quenching experiments and electron paramagnetic resonance (EPR) measurements were conducted to discuss the mechanism of PMS activation in the CMs/PMS system. The reactive oxygen species (ROS) were supposed to be SO₄˙^- and ¹O₂ in the CoCM/PMS system, ¹O₂ and O₂˙^- in the MnCM/PMS system, SO₄˙^- and ·OH in the FeCM/PMS system, and SO₄˙^- in the CuCM/PMS system, respectively. The comparative study on the performance and mechanism of the four CMs provides a better understanding of the integrated PMS-CMs behaviors.

Removal of Bisphenol A via peroxymonosulfate activation over graphite carbon nitride supported NiCx nanoclusters catalyst: Synergistic oxidation of high-valent nickel-oxo species and singlet oxygen

In this work, a g-C₃N₄ supported NiCx nanoclusters catalyst (NiCx-CN) was developed, and its performance in activating peroxymonosulfate (PMS) was evaluated. Mechanism investigation stated that although singlet oxygen (¹O₂) was formed in the catalytic process, its contribution to BPA elimination was weeny. Interestingly, through the experiment with dimethyl sulfoxide as the probe, it was considered that the high-valent nickel-oxo species (Ni^&+=O), generated after the interaction of NiCx-CN and PMS, was the dominating reactive oxygen species (ROS). Theoretical calculations (DFT) implied that NiCx-CN might lose electrons to generate high-valent Ni, which was consistent with the detection of Ni³⁺ on the surface of the used NiCx-CN. Besides, the prepared NiCx-CN showed advantages in resisting the interference of inorganic anions. Meanwhile, three BPA degradation routes had been proposed based on the transformation intermediates. This study will establish a new protocol for PMS activation using heterogeneous Ni-based catalysts to efficiently degrade organic pollutants via a nonradical mechanism.

The novel strategy of designing perovskite fiber membrane as reactor for catalytic oxidation

Negative impacts of wastewater contamination include harm to the environment, people, plants, and animals. Metal-based heterogeneous catalysts, particularly transition metal oxide catalysts, are a therapeutic option. However, they have limited reusability and cause secondary contaminations through metal leaching. In this work, a new membrane catalyst made of perovskite-type fiber was created and tested to remove methylene blue from wastewater. These innovative 3D perovskite ceramic catalysts work well in the breakdown of pollutants and dramatically lessen possible secondary contaminations caused by metal leaching from catalysts.

Application of cellulose nanocrystals in water treatment membranes: A review

Nanomaterials have brought great changes to human society, and development has gradually shifted the focus to environmentally friendly applications. Cellulose nanocrystals (CNCs) are new one-dimensional nanomaterials that exhibit environmental friendliness and ensure the biological safety of water environment. CNCs have excellent physical and chemical properties, such as simple preparation process, nanoscale size, high specific surface area, high mechanical strength, good biocompatibility, high hydrophilicity and antifouling ability. Because of these characteristics, CNCs are widely used in ultrafiltration membranes, nanofiltration membranes and reverse osmosis membranes to solve the problems hindering development of membrane technology, such as insufficient interception and separation efficiency, low mechanical strength and poor antifouling performance. This review summarizes recent developments and uses of CNCs in water treatment membranes and discusses the challenges and development prospects of CNCs materials from the perspectives of ecological safety and human health by comparing them with traditional one-dimensional nanomaterials.

Peracetic acid integrated catalytic ceramic membrane filtration for enhanced membrane fouling control: Performance evaluation and mechanism analysis

Endowing ceramic membrane (CM) catalytic reactivity can enhance membrane fouling control in the aid of in situ oxidation process. Peracetic acid (PAA) oxidant holds great prospect to integrate with CM for membrane fouling control, owing to the prominent advantages of high oxidation efficacy and easy activation. Herein, this study, for the first time, presented a PAA/CM catalytic filtration system achieving highly-efficient protein fouling alleviation. A FeOCl functionalized CM (FeOCl-CM) was synthesized, possessing high hydrophilicity, low surface roughness, and highly-efficient activation towards PAA oxidation. Using bovine serum albumin (BSA) as the model protein foulant, the PAA/FeOCl-CM catalytic filtration notably alleviated fouling occurring in both membrane pores and surface, and halved the flux reduction degree as compared with the conventional CM filtration. The PAA/FeOCl-CM catalytic oxidation allows quick and complete disintegration of BSA particles, via the breakage of the amide I and II bands and the ring opening of the aromatic amino acids (e.g., Tryptophan, Tyrosine). In-depth investigation revealed that the in situ generated ^•OH and ¹O₂ were the key reactive species towards BSA degradation during catalytic filtration, while the organic radical oxidation and the direct electron transfer pathway from BSA to PAA via FeOCl-CM played minor roles. Overall, our findings highlight a new PAA/CM catalytic filtration strategy for achieving highly-efficient membrane fouling control and provide an understanding of the integrated PAA catalytic oxidation - membrane filtration behaviors.

The pH dependent surface charging and points of zero charge. IX. Update

of the points of zero charge (PZC) and isoelectric points (IEP) of various materials published in the recent literature and of older results overlooked in the previous compilations. The roles of experimental conditions, especially of the temperature, of the nature and concentration of supporting electrolyte, and of the type of apparatus are emphasized. The newest results are compared with the zero points reported in previous reviews. Most recent studies were carried out with materials whose pH dependent surface charging is already well-documented, and the newest results are consistent with the older literature. Isoelectric points of Gd(OH)₃, Sm(OH)₃, and TeO₂ have been reported for the first time in the recent literature.

Reversible filtration redox of methylene blue in dimethylsulfoxide by manganese oxide loaded carbonaceous nanofibrous membrane through Fenton-like oxidation

The reversible redox of methylene blue in organic solvents was highly attractive, yet was rarely reported. In this study, we realized the continuous filtration redox of methylene blue (MB) in dimethylsulfoxide (DMSO) through Fenton-like oxidization by using MnO₂ loaded carbonaceous nanofibrous membrane (cPAN-MnO₂). The carbonaceous nanofibrous membrane (cPAN) was fabricated through electrospun of polyacrylonitrile and subsequent carbonization. The obtained cPAN nanofibrous membrane showed excellent stability in polar DMSO. MnO₂ can be readily coated on cPAN nanofibers through an in situ redox reaction between cPAN and potassium permanganate. The fabricated cPAN-MnO₂ membrane exhibited instantaneous reduction property towards MB in DMSO during a gravity-driven continuous filtration process. Interestingly, MB reduction was initiated by a typical Fenton-like oxidization, where hydroxyl radicals were firstly generated from hydrogen peroxide catalyzed by MnO₂ in DMSO. Then hydroxyl radicals attacked DMSO to further produce methyl radicals, which resulted in the reduction of MB. In addition, MB reduction process in DMSO was reversible. Our study provides a novel strategy for continuous redox of MB in polar organic solvent and might give new ideas for MB applications.

Sequential Ultrafiltration-Catalysis Membrane for Excellent Removal of Multiple Pollutants in Water

Clean water production calls for highly efficient and less energy-intensive technologies. Herein, a novel concept of a sequential ultrafiltration-catalysis membrane is developed by loading Co₃O₄/C@SiO₂ yolk-shell nanoreactors into the fingerlike channels of a polymeric ultrafiltration membrane. Such a sequenced structure design successfully integrates selective separation with peroxymonosulfate-based catalysis to prepare a functionalized molecular sieve membrane, which exhibits excellent decontamination performance toward multipollutants by filtering the water matrices containing humic acid (HA) and bisphenol A (BPA). In this study, 100% rejection of HA and 95% catalytic degradation of BPA were achieved under a low pressure of 0.14 MPa and an ultrahigh flux of 229 L m^-2 h^-1, corresponding to a retention time of 3.1 s. Notably, the removal performance of multiple pollutants essentially depends on the ordered arrangement of ultrafiltration and catalysis. Moreover, the flow-through process demonstrated significant enhancement of BPA degradation kinetics, which is 21.9 times higher than that of a conventional batch reactor. This study provides a novel strategy for excellent removal of multiple pollutants in water.

A stable and easily prepared copper oxide catalyst for degradation of organic pollutants by peroxymonosulfate activation

A direct one-step calcination preparation of CuO catalyst (CuO-3) using polyethylene glycol (PEG) as nonionic polymeric structure directing agent was developed for activation of peroxymonosulfate (PMS). The morphological and physicochemical properties of the CuO-3 were characterized and the catalytic activity for degradation of organic pollutants was evaluated. The resultant CuO-3 with significantly enhanced surface area exhibited excellent catalytic performance of phenolic organic pollutants degradation. The reaction mechanism of the PMS/CuO system was systematically investigated with a series of radical quenching tests and the analysis of electron paramagnetic resonance (EPR) spectroscopy. Quite different from traditional hydroxyl radicals (OH) and sulfate radical (SO₄^-) based advanced oxidation processes, singlet oxygen (¹O₂) was identified as the dominate reactive species responsible for the degradation of organic pollutants. Moreover, the main formation pathway of ¹O₂ was also investigated. The results indicated that the superoxide radical (O₂^-) was involved in the generation of ¹O₂ as a crucial precursor. Also, the PMS/CuO-3 system exhibited satisfactory stability and reusability under neutral conditions as well as high removal of organic pollutants in the presence of inorganic anions. This work not only provides a novel and stable preparation method for CuO catalyst, but also gives a deeper insight into the mechanisms of PMS activation by CuO.

Manganese oxide integrated catalytic ceramic membrane for degradation of organic pollutants using sulfate radicals

Membrane separation and advanced oxidation processes (AOPs) have been respectively demonstrated to be effective for a variety of water and/or wastewater treatments. Innovative integration of membrane with catalytic oxidation is thus expected to be more competing for more versatile applications. In this study, ceramic membranes (CMs) integrated with manganese oxide (MnO₂) were designed and fabricated via a simple one-step ball-milling method with a high temperature sintering. Functional membranes with different loadings of MnO₂ (1.67%, 3.33% and 6.67% of the total membrane mass) were then fabricated. The micro-structures and compositions of the catalytic membranes were investigated by a number of advanced characterisations. It was found that the MnO₂ nanocatalysts (10-20 nm) were distributed uniformly around the Al₂O₃ particles (500 nm) of the membrane basal material, and can provide a large amount of active sites for the peroxymonosulfate (PMS) activation which can be facilitated within the pores of the catalytic membrane. The catalytic degradation of 4-hydroxylbenzoic acid (HBA), which is induced by the sulfate radicals via PMS activation, was investigated in a cross-flow membrane unit. The degradation efficiency slightly increased with a higher MnO₂ loading. Moreover, even with the lowest loading of MnO₂ (1.67%), the effectiveness of HBA degradation was still prominent, shown by that a 98.9% HBA degradation was achieved at the permeated side within 30 min when the initial HBA concentration was 80 ppm. The stability and leaching tests revealed a good stability of the catalytic membrane even after the 6th run. Electron paramagnetic resonance (EPR) and quenching tests were used to investigate the mechanism of PMS activation and HBA degradation. Both sulfate radicals (SO₄^•-) and hydroxyl radicals (^•OH) were generated in the catalytic membrane process. Moreover, the contribution from non-radical process was also observed. This study provides a novel strategy for preparing a ceramic membrane with the function of catalytic degradation of organic pollutants, as well as outlining into future integration of separation and AOPs.