Phosphorus-doped g-C3N4 integrated photocatalytic membrane reactor for wastewater treatment

Hybrid combination of advanced oxidation process with membrane technology for wastewater treatment: gains and problems

Over the past few decades, significant efforts have been dedicated to advancing technologies for the removal of micropollutants from water. Achieving complete pure water with a single treatment process is challenging and nearly impossible. One promising approach among various alternatives is adopting hybrid technology, which is considered as a win-win technology. It utilizes the advantages of each technique, resulting in the enhancement of wastewater treatment. This pioneering idea is designed to significantly enhance water quality, addressing real-world implementation hurdles, and offer a promising solution to the worldwide issue of water scarcity. This review assesses the merits and drawbacks of the hybrid photocatalytic membrane technology employed in wastewater treatment. Notably, this hybrid process not only improves the membrane filtration capacity and permeates water quality but also enhances the antifouling performance of the membrane. However, it is crucial to acknowledge potential drawbacks, such as membrane structure degradation and photocatalytic activity loss in nanoparticles during the operation period. While improvements in wastewater treatment efficiency are evident, there remains ample room for further enhancements. The review summarizes the future directions and challenges of implementing such an integrated system.

Improving selectivity and antifouling properties of a PES hollow fibre membrane with a photo-enzyme for the removal of ciprofloxacin and sulfamethoxazole

A multifunctional hollow fibre was prepared by the modification of polyethersulfone (PES) with laccase (Lac) and phosphorus-doped graphitic carbon nitride (P-gC3N4) for the removal of ciprofloxacin and sulfamethoxazole. The properties and structure elucidation of the prepared membranes were evaluated using contact angle analysis, Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), correlative light electron microscopy (CLEM), atomic force microscopy (AFM), tensile strength, water-intake capacity, and pure water flux. The modified multifunctional hollow fibre membranes showed increased root mean square surface roughness from 50 nm for neat PES to 104 nm, which contributed to the significantly higher water flux of 90 L.m-2h-1 compared to 54 L.m-2h-1 for pristine PES. The hydrophilicity also improved after modification as the contact angle reduced from 72° ± 1.01° to 42° ± 2.26°. The modified hollow fibre membranes showed an enhanced removal of ciprofloxacin (77%) and sulfamethoxazole (80%). Moreover, antifouling properties towards bovine serum albumin were 89% for FRR, 7% for Rr, 9% for Rir and 17% for Rt. Regeneration studies showed that the multifunctional hollow fibre membrane obtained a high removal percentage of 79% towards sulfamethoxazole after five cycles. Hence, this work proposes a new system that can be successfully utilized in the treatment of emerging pharmaceutical pollutants in water.

Optimization and reusability of photocatalytic g-C3N4/W-TiO2/PVDF membranes for degradation of sulfamethazine

Pharmaceuticals and personal care products (PPCPs) are prevalent emerging pollutants in the aquatic environment. The photocatalysis process has proven high efficiency in degrading PPCPs; however, the fate and repercussions of photocatalyst residuals are a major concern. To avoid that, we developed a composite from graphitic carbon nitride/tungsten doped with titanium dioxide (g-C3N4/W-TiO2) and loaded it on polyvinylidene fluoride (PVDF) membranes by the phase-inversion method. X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), transmission electron microscopy (TEM), and other different analyses implied the successful synthesis of g-C3N4/W-TiO2 composite and coating on PVDF membranes. A Box-Behnken design (BBD) was used to optimize the operational parameters, including pH, g-C3N4 ratio in the composite, and initial SMZ concentration by the response surface methodology (RSM). The highest SMZ degradation percentage was 98.60% after 240 min of irradiation. Liquid chromatography with tandem mass spectrometry (LC-MS/MS) along with suspect screening was used to identify the intermediate transformation products and propose the SMZ degradation pathway. The loss in membrane activity after five cycles of photocatalytic degradation was about 18%. According to the current study, the photocatalytic membrane g-C3N4/W-TiO2/PVDF is promising for removing sulfonamide antibiotics from wastewater.

A critical review on non-metal doped g-C3N4 based photocatalyst for organic pollutant remediation with sustainability assessment by life cycle analysis

Photocatalysis is recognized to be one of the most promising ways to address energy and environmental issues by utilizing visible light. Graphitic carbon nitride (g-C3N4), with a moderate band gap (∼2.7 eV) has been the flashpoint in environmental photocatalysis as it can work better under visible light, can be synthesized by a facile synthesis process using low-cost materials, thermally and chemically stable. Still the photocatalytic performance of g-C3N4 is not satisfactory because of certain limitations such as insufficient visible light absorption capacity, low electron-hole separation efficiency, high recombination rate, poor surface area. Introduction of doping, band structure engineering, defecting and designing of heterojunction, composites etc. were investigated to amplify its applications. Among all these modifications, elemental doping is a suitable and successful alternative for the enhancement of the photocatalytic activity by changing the optical and electronic properties. This review emphasizes on advancement and trends of elemental doping and its application on photocatalytic organic pollutant remediation in aqueous medium. The fundamental photocatalytic activity of heterogeneous photocatalysis and specifically g-C3N4-based photocatalysis have been discussed. The benfits of non-metal doping, enhanced photocatalytic performance by doping element, mechanism invloved in doping, advantages of co-doping has been explained. Mono, bi, and tri non-metal doped g-C3N4 and their application for the removal of organic pollutants from water medium by visible light photocatalysis has been summerized. Life cycle assessment (LCA) of photocatalytic system has been highlighted. Future research should focus on the large-scale application of the photocatalysis process considering the economic aspects. A rigorous life cycle assessment for deploying the non-metal doped g-C3N4-based photocatalysis technology for successful commercial application is recommended.

Boosting the photocatalytic activity of g-C3N4 via loading bio-synthesized Ag0 nanoparticles and imidazole modification for the degradation and mineralization of fluconazole

The emergence of fluorinated organic compounds in the pharmaceutical, agrochemical, and textile industries has led to a potential increase in the environmental issues and health problems. Herein, a modified heterojunction of bio-synthesized Ag nanoparticles (Ag0 NPs) immobilized on imidazole-modified graphite carbon nitride (Im/g-C3N4) as a suitable support (Ag0/Im/g-C3N4) was hydrothermally synthesized and studied for the photocatalytic removal of the most widely used antifungal organo-fluorine compound-fluconazole (FCZ). The optical properties were thoroughly investigated in the present study, and it was observed that the proposed modification to g-C3N4 has led to the shifting of conduction and valance band edge position (for g-C3N4, -0.73 and 1.54 eV and for ICA, -1.14 and 1.28 eV), narrowing of band gap energies, i.e., 2.01 eV, and reduced charge recombination rate. The external and internal surface morphologies were scrutinized through FE-SEM and HR-TEM analyses. Functionalities and potential crystallinity were investigated using FTIR and XRD techniques. The elemental state and composition of the composite were analyzed via XPS. The obtained results substantiate the intended modifications in the ICA composite. The photocatalyst Ag0/Im/g-C3N4 (ICA) was able to degrade 95.74% of FCZ with a high degradation rate (k1) of 0.0289 min-1 within 2-h of the solar illumination experiment. The overall degradation process was observed to be governed by a pseudo-first-order kinetic model. Detailed parameters such as effects of ions, pH (optimized pH 4, highest degradation rate k1 =0.039 min-1), dissolved organic matter (DOM), and optimization of catalysts dosage were studied. The major reactive oxygen species (ROS) was identified as super-oxide radicals (O2●-). The HR-MS and COD-TOC analysis were used to evaluate the degradation and mineralization of FCZ forced by ICA catalysts. The ICA catalyst was found to be stable and reusable for up to five cycles suggesting towards its potential towards the mitigation of environmental pollutants.

Optimization of Electron Transport Pathway: A Novel Strategy to Solve the Photocorrosion of Ag-Based Photocatalysts

Although Ag-containing photocatalysts exhibit excellent photocatalytic ability, they present great challenges owing to their photocorrosion and ease of reduction. Herein, an electron acceptor platform of Ag2O/La(OH)3/polyacrylonitrile (PAN) fiber was constructed using a heterojunction strategy and electrospinning technology to develop a novel photocatalytic membrane with a redesigned electron transport pathway. Computational and experimental results demonstrate that the optimized electron transport pathway included intercrystal electron transfer induced by the La-O bond between Ag2O and La(OH)3 as well as electron transfer between the catalyst crystal and electrophilic PAN membrane interface. In addition, the photocatalytic performance of the Ag2O/La(OH)3 membrane for tetracycline (TC) removal was still above 97% after five photocatalytic reaction cycles. Furthermore, the carrier life was greatly extended. Mechanistic study revealed that photogenerated holes on the Ag2O/La(OH)3 membrane were the main reactive species in TC degradation. Overall, this study proposes a novel electron transport pathway strategy that effectively solves the problems of photocatalyst photocorrosion and structural instability.

Impact of nitrogen doping on triazole-based graphitic carbon Nitride-TiO2 (P25) S-scheme heterojunction for improved photocatalytic hydrogen production

Establishing an S-scheme heterojunction is a promising method for increasing the photocatalytic activity of synthetic materials. In this study, nitrogen-doped g-C3N5/TiO2 S-scheme photocatalysts have been synthesized and examined for photocatalytic hydrogen production using thermal decomposition methods. Nitrogen-doped g-C3N5/TiO2 composites performed better than pure nitrogen-doped g-C3N5 and TiO2 alone. Using experiments and density functional theory (DFT) calculations, nitrogen (N) doping was identified as being introduced by replacing the carbon (C) atoms in the matrix of g-C3N5. In addition to its narrow band gap, N-doped g-C3N5 showed efficient carrier separation and charge transfer, resulting in the enhanced absorption of visible light and photocatalytic activity. DFT, XPS, optical property characteristics, and PL spectra confirmed these findings, which were attributed to the successful nitrogen doping, and the composite was proven to be a potential candidate for photocatalytic hydrogen generation under light irradiation. The quantity of H2 produced from the nitrogen-doped g-C3N5/TiO2 composite for 3 hours (3515.1 μmol g-1) was about three times that of N-doped g-C3N5. The H2 production percentage of the nitrogen-doped g-C3N5/TiO2 catalyst with Pt as the cocatalyst was improved by nearly ten times as compared to N-doped g-C3N5/TiO2 without a cocatalyst. Herein, we report the successful preparation of the N-doped g-C3N5/TiO2 S-scheme heterojunction and highlight a simple and efficient catalyst for energy storage requirements and environmental monitoring.

Photocatalytic hydrogel film assisted forward osmosis (PFO) for water treatment: Sustainable performance and contaminant control

The integration of catalytic oxidation with forward osmosis (FO) holds promising potential to address two crucial challenges encountered by FO: fouling and unsustainable performance, but suitable approaches are still rare. Herein, we have successfully developed a photocatalysis-assisted forward osmosis (PFO) system. In the PFO, a self-made porous carbon nitride doped functional carbon nanotube photocatalytic hydrogel film (PCN@CNTM) was engaged in the FO process in an inventive way by simply sticking to the commercial FO membrane surface, preventing damage to the membrane from the catalyst's direct insertion and delaying the assault from the oxidation groups. PFO allowed organic pollutants to decompose in the feed solution (90%) and on the membrane surface, regulating the water chemical potential and giving the FO membrane antifouling properties. This resulted in sustainable water flux (11.8 LMH) with no significant membrane fouling in PFO, whereas in FO alone there was a significant fouling and flux drop (from 12.73 to 7.23 LMH in 4 h). Moreover, the expensive FO membrane was protected while the hydrogel film can be replaced on demand. The PFO exemplifies the concept of synergistic technology integration, presenting a new perspective on harnessing the strengths of distinct technologies in a mutually beneficial manner.

Simultaneously Achieving Fast Intramolecular Charge Transfer and Mass Transport in Holey D-π-A Organic Conjugated Polymers for Highly Efficient Photocatalytic Pollutant Degradation

Simultaneously realizing efficient intramolecular charge transfer and mass transport in metal-free polymer photocatalysts is critical but challenging for environmental remediation. Herein, we develop a simple strategy to construct holey polymeric carbon nitride (PCN)-based donor-π-acceptor organic conjugated polymers via copolymerizing urea with 5-bromo-2-thiophenecarboxaldehyde (PCN-5B2T D-π-A OCPs). The resultant PCN-5B2T D-π-A OCPs extended the π-conjugate structure and introduced abundant micro-, meso-, and macro-pores, which greatly promoted intramolecular charge transfer, light absorption, and mass transport and thus significantly enhanced the photocatalytic performance in pollutant degradation. The apparent rate constant of the optimized PCN-5B2T D-π-A OCP for 2-mercaptobenzothiazole (2-MBT) removal is ∼10 times higher than that of the pure PCN. Density functional theory calculations reveal that the photogenerated electrons in PCN-5B2T D-π-A OCPs are much easier to transfer from the donor tertiary amine group to the benzene π-bridge and then to the acceptor imine group, while 2-MBT is more easily adsorbed on π-bridge and reacts with the photogenerated holes. A Fukui function calculation on the intermediates of 2-MBT predicted the real-time changing of actual reaction sites during the entire degradation process. Additionally, computational fluid dynamics further verified the rapid mass transport in holey PCN-5B2T D-π-A OCPs. These results demonstrate a novel concept toward highly efficient photocatalysis for environmental remediation by improving both intramolecular charge transfer and mass transport.

Photocatalysts for a sustainable future: Innovations in large-scale environmental and energy applications

The growing environmental and energy crises have prompted researchers to seek new solutions, including large-scale photocatalytic environmental remediation and the production of solar hydrogen using photocatalytic materials. To achieve this goal, scientists have developed numerous photocatalysts with high efficiency and stability. However, the large-scale application of photocatalytic systems under real-world conditions is still limited. These limitations arise at every step, including the large-scale synthesis and deposition of photocatalyst particles on a solid support, and the development of an optimal design with high mass transfer and efficient photon absorption. The purpose of this article is to provide a detailed description of the primary challenges and potential solutions encountered in scaling up photocatalytic systems for use in large-scale water and air purification and solar hydrogen production. Additionally, based on a review of current pilot developments, we draw conclusions and make comparisons regarding the main operating parameters that affect performance, as well as propose strategies for future research.

An Overview of Photocatalytic Membrane Degradation Development

Environmental pollution has become a worldwide issue. Rapid industrial and agricultural practices have increased organic contaminants in water supplies. Hence, many strategies have been developed to address this concern. In order to supply clean water for various applications, high-performance treatment technology is required to effectively remove organic and inorganic contaminants. Utilizing photocatalytic membrane reactors (PMRs) has shown promise as a viable alternative process in the water and wastewater industry due to its efficiency, low cost, simplicity, and low environmental impact. PMRs are commonly categorized into two main categories: those with the photocatalyst suspended in solution and those with the photocatalyst immobilized in/on a membrane. Herein, the working and fouling mechanisms in PMRs membranes are investigated; the interplay of fouling and photocatalytic activity and the development of fouling prevention strategies are elucidated; and the significance of photocatalysis in membrane fouling mechanisms such as pore plugging and cake layering is thoroughly explored.

Photoinduced Absorption Spectroscopy of Photoelectrocatalytic Methylene Blue Oxidation on Titania and Hematite: The Thermodynamic and Kinetic Impacts on Reaction Pathways

Photoelectrochemical oxidation of methylene blue is investigated, with particular focus on the difference in kinetics and thermodynamics of decoloration and mineralization employing photoinduced absorption spectroscopy. Hematite and titania photoanodes are used for the comparison of both reactions, which is determined to be associated with the depth of the valence band (3.2 vs 2.5 V for titania and hematite, respectively). Methylene blue is mineralized by the titania photoanode, however it is only oxidized to small fragments by hematite. Such difference is related to the valence band potential that provides the thermodynamic driving force for photogenerated holes in both materials. In addition, the kinetic competition of water oxidation is found to occur on titania by controlling the pH of the electrolyte. In the pH 14 electrolyte, mineralization of methylene blue is suppressed due to the faster and dominant kinetics of water oxidation, in contrast to the complete mineralization in the near neutral electrolyte where water oxidation kinetics are modest. These results clearly address the importance considering both thermodynamic and kinetic challenges of methylene blue oxidation, which has been thought to be an easy molecule to oxidize, as the model reaction in the application of photo(electro)catalysis using metal oxides.

Investigation on the Performance of CO2 Absorption in Ceramic Hollow-Fiber Gas/Liquid Membrane Contactors

The absorption efficiencies of CO₂ in ceramic hollow-fiber membrane contactors using monoethanolamine (MEA) absorbent under both cocurrent- and countercurrent-flow operations were investigated theoretically and experimentally; various MEA absorbent flow rates, CO₂ feed flow rates, and inlet CO₂ concentrations were used as parameters. Theoretical predictions of the CO₂ absorption flux were analyzed by developing the mathematical formulations based on Happel's free surface model in terms of mass transfer resistances in series. The experiments of the CO₂ absorption were conducted by using alumina (Al₂O₃) hollow-fiber membranes to confirm the accuracy of the theoretical predictions. The simplified expression of the Sherwood number was formulated to calculate the mass transfer coefficient of the CO₂ absorption incorporating experimental data. The data were obtained numerically using the fourth-order Runge-Kutta method to predict the concentration distribution and absorption rate enhancement under various fiber packing configurations accomplished by the CO₂/N₂ stream passing through the fiber cells. The operations of the hollow-fiber membrane contactor encapsulating N = 7 fiber cells and N = 19 fiber cells of different packing densities were fabricated in this work to examine the device performance. The accuracy derivation between experimental results and theoretical predictions for cocurrent- and countercurrent-flow operations were 1.31×10-2≤E≤4.35×10-2 and 3.90×10-3≤E≤2.43×10-2, respectively. A maximum of 965.5% CO₂ absorption rate enhancement was found in the module with embedding multiple fiber cells compared with that in the device with inserting single-fiber cell. Implementing more fiber cells offers an inexpensive method of improving the absorption efficiency, and thus the operations of the ceramic hollow-fiber membrane contactor with implementing more fiber cells propose a low-priced design to improve the absorption rate enhancement. The higher overall CO₂ absorption rate was achieved in countercurrent-flow operations than that in cocurrent-flow operations.

Phosphorous- and Boron-Doped Graphene-Based Nanomaterials for Energy-Related Applications

Doping is a great strategy for tuning the characteristics of graphene-based nanomaterials. Phosphorous has a higher electronegativity as compared to carbon, whereas boron can induce p-type conductivity in graphene. This review provides insight into the different synthesis routes of phosphorous- and boron-doped graphene along with their applications in supercapacitors, lithium- ions batteries, and cells such as solar and fuel cells. The two major approaches for the synthesis, viz. direct and post-treatment methods, are discussed in detail. The former synthetic strategies include ball milling and chemical vapor discharge approaches, whereas self-assembly, thermal annealing, arc-discharge, wet chemical, and electrochemical erosion are representative post-treatment methods. The latter techniques keep the original graphene structure via more surface doping than substitutional doping. As a result, it is possible to preserve the features of the graphene while offering a straightforward handling technique that is more stable and controllable than direct techniques. This review also explains the latest progress in the prospective uses of graphene doped with phosphorous and boron for electronic devices, i.e., fuel and solar cells, supercapacitors, and batteries. Their novel energy-related applications will continue to be a promising area of study.

Synthesis and applications of graphitic carbon nitride (g-C3N4) based membranes for wastewater treatment: A critical review

Semiconducting membrane combined with nanomaterials is an auspicious combination that may successfully eliminate diverse waste products from water while consuming little energy and reducing pollution. Creating an inexpensive, steady, flexible, and diversified business material for membrane production is a critical challenge in membrane technology development. Because of its unusual structure and high catalytic activity, graphitic carbon nitride (g-C3N4) has come out as a viable material for membranes. Furthermore, their great durability, high permanency under challenging environments, and long-term use without decrease in flux are significant advantages. The advanced material techniques used to manage the molecular assembly of g-C3N4 for separation membrane were detailed in this review work. The progress in using g-C3N4-based membranes for water treatment has been detailed in this presentation. The review delivers an updated description of g-C3N4 based membranes and their separation functions and new ideas for future enhancements/adjustments to address their weaknesses in real-world situations. Finally, the ongoing problems and promising future research directions for g-C3N4-based membranes are discussed.

Removal of tetracycline from wastewater using g-C3N4 based photocatalysts: A review

Tetracycline is currently one of the most consumed antibiotics for human therapy, veterinary purpose, and agricultural activities. Tetracycline worldwide consumption is expected to rise by about more than 30% by 2030. The persistence of tetracycline has necessitated implementing and adopting strategies to protect aquatic systems and the environment from noxious pollutants. Here, graphitic carbon nitride-based photocatalytic technology is considered because of higher visible light photocatalytic activity, low cost, and non-toxicity. Thus, this review highlights the recent progress in the photocatalytic degradation of tetracycline using g-C₃N₄-based photocatalysts. Additionally, properties, worldwide consumption, occurrence, and environmental impacts of tetracycline are comprehensively addressed. Studies proved the occurrence of tetracycline in all water matrices across the world with a maximum concentration of 54 μg/L. Among different g-C₃N₄-based materials, heterojunctions exhibited the maximum photocatalytic degradation of 100% with the reusability of 5 cycles. The photocatalytic membranes are found to be feasible due to easiness in recovery and better reusability. Limitations of g-C₃N₄-based wastewater treatment technology and efficient solutions are also emphasized in detail.

Recent Advances in g-C3 N4 -Based Photocatalysts for Pollutant Degradation and Bacterial Disinfection: Design Strategies, Mechanisms, and Applications

Emerging photocatalytic technology promises to provide an effective solution to the global energy crisis and environmental pollution. Graphite carbon nitride (g-C₃ N₄ ) has gained extensive attention in the scientific community due to its excellent physical and chemical properties, attractive electronic band structure, and low cost. In this paper, research progress in design strategies for g-C₃ N₄ -based photocatalysts in the past five years is reviewed from the perspectives of nanostructure construction, element doping, and heterostructure construction. To clarify the relationship between application requirements and structural design, variations in the morphology, electronic energy band structure, light absorption capacity, as well as interfacial charge transfer caused by various modification strategies are discussed in detail. The recent applications of g-C₃ N₄ -based photocatalysts for pollutant degradation and bacterial disinfection are reviewed, as well as the antimicrobial activity and degradation mechanisms. Finally, current challenges and future development directions for the practical application of g-C₃ N₄ -based photocatalysts are tentatively discussed.

Photocatalytic membrane reactors for produced water treatment and reuse: Fundamentals, affecting factors, rational design, and evaluation metrics

Treatment and reuse of produced water (PW), the largest wastewater stream generated during oil and gas production, provides a promising option to address the increasing clean water demands. High-performance treatment technologies are needed to efficiently remove the organic and inorganic contaminants in PW for fit-for-purpose applications. Photocatalytic membrane reactor (PMR) is an emerging green technology for removal of organic pollutants, photoreduction of heavy metals, photo-inactivation of bacteria, and resource recovery. This study critically reviewed the mechanisms of photocatalysis and membrane processes in PMR, factors affecting PMR performance, rational design, and evaluation metrics for PW treatment. Specifically, PW characteristics, photocatalysts properties, membranes applied, and operating conditions are of utmost importance for rational design and reliable operation of PMR. PW pretreatment to remove oil and grease, colloidal and suspended solids is necessary to reduce membrane fouling and ensure optimal PMR performance. The metrics to evaluate PMR performance were developed including light utilization, exergetic efficiency, water recovery, product water improvement, lifetime of the photocatalyst, and costs. This review also presented the research gaps and outlook for future research.

Semiconducting graphitic carbon nitride integrated membranes for sustainable production of clean water: A review

Semiconducting membranes integrated with nanomaterials have placed themselves in new emerging researches tremendously for seawater desalination, oil-water separation, disinfection, removal of inorganic as well as organic pollutants. Howbeit, only nanoparticles unified membranes show quite a lot lags in their performance, although some of these particles associated with the demerits of high cost. In contrast, graphitic carbon nitride incorporated membranes offered improved aforementioned properties corresponding to absolute essential qualities such as cost-effective, environmentally friendly, easy-to-operate, green manufacturing, anti-fouling, and low energy consumption. Moreover, their high mechanical strength, high stability against harsh environment and long-term utilization without flux reduction are strong plus. Even though there are some undeniable downsides of these membranes in real world applications as bulk synthesis, consistent dispersion of graphitic carbon nitride, low photocatalytic efficiency etc. Accordingly, in the present article, these frailties of the membranes having graphitic carbon nitride as a filler and their respective synthesis procedures and properties are discussed. A comprehensive analysis over the application of semiconducting graphitic carbon nitride incorporated membranes with and without special surface modification; and exploration of the future challenges and difficulties associated to these membranes are also reviewed. Consequently, the current article provides brief overview about graphitic carbon nitride integrated composite membranes as well as their applications, and it finished up with new thoughts of further improvements/modifications to overcome their shortcomings in actual environmental conditions.

A review on graphitic carbon nitride (g-C3N4) based hybrid membranes for water and wastewater treatment

Graphitic carbon nitride (g-C₃N₄) has gained enormous attention for water and wastewater treatment. Compared with g-C₃N₄ nanopowders, g-C₃N₄ based hybrid membranes have demonstrated great potential for its superior practicability. This review outlines the preparation and characterization of g-C₃N₄ based hybrid membranes and presents their representative applications in water and wastewater treatment (e.g., removal of organic dyes, phenolic compounds, pharmaceuticals, salt ions, heavy metals, and oils). Meanwhile, g-C₃N₄ based films for the removal of contaminants through photocatalytic degradation is also summarized. In addition, the corresponding mechanisms and relevant findings are discussed. Finally, the challenges and research needs in the future and application of g-C₃N₄ based hybrid membranes are highlighted.

Synthesis of graphitic carbon nitride/cadmium sulfide core-shell nanofibers for enhanced photocatalysis

The synthesis of graphitic carbon nitride/cadmium sulfide core-shell nanofibers has been studied for the improved photodegradation of methylene blue (MB) dye. The enhancement in photocatalytic activity in g-C₃N₄@CdS core-shell nanostructures has been increased by controlling the thickness of the CdS shell. Additionally, the favorable bandgap, suitable band positions, and high thermal stability played an important role to enhance the photodegradation rate of catalysts. g-C₃N₄@CdS core-shell nanofiber arrays were synthesized by using a simple two-step process. g-C₃N₄ nanofiber (gcnf) was synthesized by using a simple polycondensation method and followed by a surface modification step for the deposition of CdS nanoparticles. The characterization of core-shell nanofibers and their photocatalytic activity was examined by powder X-ray diffraction, UV-Vis spectrophotometer, FESEM, EDS, and TEM microscopy. g-C₃N₄@CdS core-shell nanofibers (gcnf/CdS, 0.38; gcnf/CdS, 0.19; and gcnf/CdS, 0.09) showed enhanced photocatalytic degradation efficiency of ~ 98% in 40, 50, and 70 min, respectively. Pristine g-C₃N₄ nanofibers and CdS nanoparticles displayed the photodegradation efficiency of ~ 98% in 100 and 170 min, respectively. gcnf/CdS, 0.38 core-shell nanofibers (0.38 M of citric acid), offered the highest photodegradation rate of 0.0624 min^-1, which is ~ 2.5- and 3-fold higher than pristine g-C₃N₄ nanofibers and CdS nanoparticles, respectively. The increase in the photodegradation rate of the g-C₃N₄@CdS core-shell nanostructure is due to the synergetic effect of g-C₃N₄ and CdS. Thus, the present work highlights the enhanced photocatalytic activity and stability of g-C₃N₄@CdS core-shell nanofibers and found to be useful in energy harvesting and environmental remediation applications.

Recent Status and Prospects on Thermochemical Heat Storage Processes and Applications

Recent contributions to thermochemical heat storage (TCHS) technology have been reviewed and have revealed that there are four main branches whose mastery could significantly contribute to the field. These are the control of the processes to store or release heat, a perfect understanding and designing of the materials used for each storage process, the good sizing of the reactor, and the mastery of the whole system connected to design an efficient system. The above-mentioned fields constitute a very complex area of investigation, and most of the works focus on one of the branches to deepen their research. For this purpose, significant contributions have been and continue to be made. However, the technology is still not mature, and, up to now, no definitive, efficient, autonomous, practical, and commercial TCHS device is available. This paper highlights several issues that impede the maturity of the technology. These are the limited number of research works dedicated to the topic, the simulation results that are too illusory and impossible to implement in real prototypes, the incomplete analysis of the proposed works (simulation works without experimentation or experimentations without prior simulation study), and the endless problem of heat and mass transfer limitation. This paper provides insights and recommendations to better analyze and solve the problems that still challenge the technology.

Influence of Phosphorus Doping on Triazole-Based g-C3N5 Nanosheets for Enhanced Photoelectrochemical and Photocatalytic Performance

Triazole-based g-C₃N₅, a potential catalyst, has received little attention over the years. We prepared phosphorus-doped g-C₃N₅ with one triazole and two triazine units for the first time to investigate its photoelectrochemical (PEC) and photocatalytic properties. The doping states and crystalline structures of the samples were determined using X-ray techniques, namely, X-ray diffraction, X-ray photoelectron spectroscopy, and X-ray absorption fine structure analysis. Our results suggested that the phosphorus was substituted into carbon sites form P-N/P═N bonds with four coordination, which contribute P 2p level donor states in the band gap to enhance light absorption and reduce charge separation. Therefore, P-doped g-C₃N₅ exhibited higher PEC current density and better photocatalytic efficiency toward the degradation of rhodamine B dye or tetracycline under light irradiation compared to the undoped g-C₃N₅ sample. However, excess phosphorus doping resulted in the formation of impurities and disrupted the triazine and triazole units, reducing the PEC and photocatalytic efficiency. In summary, P-doped g-C₃N₅ was successfully prepared in the present study and represents a promising, facile, and effective catalyst for energy applications and environmental remediation.

Reversible filtration redox of methylene blue in dimethylsulfoxide by manganese oxide loaded carbonaceous nanofibrous membrane through Fenton-like oxidation

The reversible redox of methylene blue in organic solvents was highly attractive, yet was rarely reported. In this study, we realized the continuous filtration redox of methylene blue (MB) in dimethylsulfoxide (DMSO) through Fenton-like oxidization by using MnO₂ loaded carbonaceous nanofibrous membrane (cPAN-MnO₂). The carbonaceous nanofibrous membrane (cPAN) was fabricated through electrospun of polyacrylonitrile and subsequent carbonization. The obtained cPAN nanofibrous membrane showed excellent stability in polar DMSO. MnO₂ can be readily coated on cPAN nanofibers through an in situ redox reaction between cPAN and potassium permanganate. The fabricated cPAN-MnO₂ membrane exhibited instantaneous reduction property towards MB in DMSO during a gravity-driven continuous filtration process. Interestingly, MB reduction was initiated by a typical Fenton-like oxidization, where hydroxyl radicals were firstly generated from hydrogen peroxide catalyzed by MnO₂ in DMSO. Then hydroxyl radicals attacked DMSO to further produce methyl radicals, which resulted in the reduction of MB. In addition, MB reduction process in DMSO was reversible. Our study provides a novel strategy for continuous redox of MB in polar organic solvent and might give new ideas for MB applications.

Drawing on Membrane Photocatalysis for Fouling Mitigation

Photocatalysis is an effective and environmentally friendly approach for degrading organic pollutants, particularly in scenarios where sunlight can be utilized as the energy source. Opportunities are emerging to apply materials and methods from photocatalytic pollutant degradation to address the challenge of fouling. Membrane fouling, attributed to organic foulants, is a prevalent problem for all membrane-based technologies and represents a major deleterious impact on membrane performance. Integration of tactics developed in photocatalysis more broadly to membranes reveals new strategies for membrane fouling control-an approach taken by an increasing number of researchers. This review summarizes key developments in photocatalytic materials and methods in water treatment and presents recent progress in the development of processes for photocatalytic alleviation of membrane fouling, including photocatalyst design and modification strategies aimed at enhancing photocatalytic efficiency, as well as different configurations of photocatalysis-membrane systems (PMS). Perspectives on future research and development opportunities for photocatalytic membrane fouling control are also provided.

Solar Light-Irradiated Photocatalytic Degradation of Model Dyes and Industrial Dyes by a Magnetic CoFe2O4-gC3N4 S-Scheme Heterojunction Photocatalyst

Magnetic CoFe₂O₄-gC₃N₄ nanocomposites were successfully synthesized, and their photocatalytic activities toward the decomposition of model synthetic dyes (e.g., methylene blue, methyl orange, and Congo red) in the presence of H₂O₂ were evaluated under simulated solar light irradiation. The 50CoFe₂O₄-50gC₃N₄ nanocomposite exhibited the highest catalytic activity. The catalytic activity of 50CoFe₂O₄-50gC₃N₄ toward the photodegradation of some industrially used dyes (such as Drimaren Turquoise CL-B p, Drimaren Yellow CL-2R p, and Drimaren Red CL-5B p) was also examined, and the catalyst exhibited its capability to decompose the industrial dyes completely. An aqueous mixture of these dyes was prepared to mimic the dye-containing wastewater, which was fully photodegraded within 30 min. 50CoFe₂O₄-50gC₃N₄ also exhibited facile magnetic separability from the reaction mixture after the accomplishment of photocatalysis reaction and stable performance after five cycles. The high photocatalytic efficiency to degrade several dyes, including dyes used in textile industries, under solar light irradiation makes 50CoFe₂O₄-50gC₃N₄ a promising photocatalyst for the treatment of dye-containing wastewater discharged from industries.

Construction of Charring-Functional Polyheptanazine towards Improvements in Flame Retardants of Polyurethane

Nitrogen-containing flame retardants have been extensively applied due to their low toxicity and smoke-suppression properties; however, their poor charring ability restricts their applications. Herein, a representative nitrogen-containing flame retardant, polyheptanazine, was investigated. Two novel, cost-effective phosphorus-doped polyheptazine (PCN) and cobalt-anchored PCN (Co@PCN) flame retardants were synthesized via a thermal condensation method. The X-ray photoelectron spectroscopy (XPS) results indicated effective doping of P into triazine. Then, flame-retardant particles were introduced into thermoplastic polyurethane (TPU) using a melt-blending approach. The introduction of 3 wt% PCN and Co@PCN could remarkably suppress peak heat release rate (pHRR) (48.5% and 40.0%), peak smoke production rate (pSPR) (25.5% and 21.8%), and increasing residues (10.18 wt%→17.04 wt% and 14.08 wt%). Improvements in charring stability and flame retardancy were ascribed to the formation of P-N bonds and P=N bonds in triazine rings, which promoted the retention of P in the condensed phase, which produced additional high-quality residues.

Effective Decolorization of Rhodamine B by a Ti Foam-Based Photocatalytic Membrane Reactor

In this study, a Ti foam-based photocatalytic membrane reactor (PMR) was constructed for rhodamine B (RhB) wastewater decolorization. Ti foam was chosen as a membrane and visible-light-driven C₃N₄ was chosen as a photocatalyst. The results showed that the decolorization efficiency could be up to 100% with a flow rate of 6.93 mL/min when the PMR was applied in the treatment of a 30 mg/L RhB solution and the concentration of C₃N₄ was 1 g/L. pH played an important role in the decolorization performance of the PMR. Alkalinity was not conducive to the decolorization of RhB in the PMR, which was mainly due to the property that RhB was difficult to dissolve in an alkaline solution. Membrane fouling was mainly caused by a C₃N₄ photocatalyst, while the effect of RhB on membrane fouling was negligible. Membrane fouling could be retarded when the PMR was applied for RhB treatment under visible-light irradiation, which was because of photoinduced hydrophilicity of C₃N₄. The membrane flux could be restored to its initial values after simple ultrasonic cleaning and backwashing. This was due to the large difference between the pore size of Ti foam and the particle size of C₃N₄ and the super hydrophilicity of Ti foam and C₃N₄.

Visible-Light Photocatalysts and Their Perspectives for Building Photocatalytic Membrane Reactors for Various Liquid Phase Chemical Conversions

Photocatalytic organic synthesis/conversions and water treatment under visible light are a challenging task to use renewable energy in chemical transformations. In this review a brief overview on the mainly employed visible light photocatalysts and a discussion on the problems and advantages of Vis-light versus UV-light irradiation is reported. Visible light photocatalysts in the photocatalytic conversion of CO2, conversion of acetophenone to phenylethanol, hydrogenation of nitro compounds, oxidation of cyclohexane, synthesis of vanillin and phenol, as well as hydrogen production and water treatment are discussed. Some applications of these photocatalysts in photocatalytic membrane reactors (PMRs) for carrying out organic synthesis, conversion and/or degradation of organic pollutants are reported. The described cases show that PMRs represent a promising green technology that could shift on applications of industrial interest using visible light (from Sun) active photocatalysts.

Surface defective g-C3N4-xClx with unique spongy structure by polarization effect for enhanced photocatalytic removal of organic pollutants

Natural sponge is an ancient marine organism with a single lamellar structure, on which there are abundant porous channels to compose full-fledged spatial veins. Illumined by the natural spongy system, herein, the Cl doped surface defective graphite carbon nitride (g-C₃N_4-xCl_x) was constructed through microwave etching. In this process, microwave with HCl was employed to produce surface defects and peel bulk g-C₃N₄ to form natural spongy structured g-C₃N_4-xCl_x with three-dimensional networks. The spongy structure of the photocatalyst could provide abundant and unobstructed pathways for the transfer and separation of electron-hole pairs, and it was beneficial for photocatalytic reaction. The spongy defective g-C₃N_4-xCl_x achieved excellent degradation of diclofenac sodium (100%), bisphenol A (88.2%), phenol (85.7%) and methylene blue (97%) solution under simulated solar irradiation, respectively. The chlorine atoms were introduced into the g-C₃N₄ skeleton in microwave field with HCl, forming C-Cl bonds and surface polarization field, which could significantly accelerate the separation of photogenerated electrons and holes. As an efficient and universal approach, microwave etching can be generally used to create surface defects for most photocatalysts, which may have potential applications in environmental purification, energy conversion and photodynamic therapy.

2D Nanocomposite Membranes: Water Purification and Fouling Mitigation

In this study, the characteristics of different types of nanosheet membranes were reviewed in order to determine which possessed the optimum propensity for antifouling during water purification. Despite the tremendous amount of attention that nanosheets have received in recent years, their use to render membranes that are resistant to fouling has seldom been investigated. This work is the first to summarize the abilities of nanosheet membranes to alleviate the effect of organic and inorganic foulants during water treatment. In contrast to other publications, single nanosheets, or in combination with other nanomaterials, were considered to be nanostructures. Herein, a broad range of materials beyond graphene-based nanomaterials is discussed. The types of nanohybrid membranes considered in the present work include conventional mixed matrix membranes, stacked membranes, and thin-film nanocomposite membranes. These membranes combine the benefits of both inorganic and organic materials, and their respective drawbacks are addressed herein. The antifouling strategies of nanohybrid membranes were divided into passive and active categories. Nanosheets were employed in order to induce fouling resistance via increased hydrophilicity and photocatalysis. The antifouling properties that are displayed by two-dimensional (2D) nanocomposite membranes also are examined.

Mechanism of sonication time on structure and adsorption properties of 3D peanut shell/graphene oxide aerogel

A 3D pretreated peanut shell-supported graphene oxide (PPS/GO) aerogel has been facilely prepared through a brief sonication + freeze-shaping technique, avoiding the traditional application of hydrothermal method which suffered from high temperature and long reaction time as well as significant loss of oxygen-containing functional groups. It was then employed to efficient norfloxacin (NOR) removal from aqueous medium. The mechanism of sonication time on the structure and adsorption properties of as-obtained PPS/GO aerogels was emphatically discussed via combining instrumental analyses, batch adsorption experiments and density functional theory (DFT) calculations. Results showed that the 3D PPS/GO aerogel with a decrease in oxygen functional groups and an increase in sp²-derived sp³ hybridization regions was observed as sonication time provided in excess, causing the worse removal efficiency towards NOR. The resulting PPS/GO(5:1) aerogel obtained at sonication of 2 min and GO loading content of 200 mg/(PPS)g exhibited the optimal NOR adsorption capacity (pH 6.2, 228.83 mg g^-1). DFT calculations further identified that the sp³-hybridized areas in PPS/GO aerogel had much lower adsorption energy (ΔE, -6.69 kcal/mol) towards NOR as compared with that of sp²-hybridized zones (-12.45 kcal/mol). In addition, multiple interactions were involved in the adsorption of NOR by 3D PPS/GO aerogel, including electrostatic attraction, H-bonding, π-π conjugation and hydrophobic effect.

Application of Hybrid Membrane Processes Coupling Separation and Biological or Chemical Reaction in Advanced Wastewater Treatment

The rapid urbanization and water shortage impose an urgent need in improving sustainable water management without compromising the socioeconomic development all around the world. In this context, reclaimed wastewater has been recognized as a sustainable water management strategy since it represents an alternative water resource for non-potable or (indirect) potable use. The conventional wastewater remediation approaches for the removal of different emerging contaminants (pharmaceuticals, dyes, metal ions, etc.) are unable to remove/destroy them completely. Hybrid membrane processes (HMPs) are a powerful solution for removing emerging pollutants from wastewater. On this aspect, the present paper focused on HMPs obtained by the synergic coupling of biological and/or chemical reaction driven processes with membrane processes, giving a critical overview and particular emphasis on some case studies reported in the pertinent literature. By using these processes, a satisfactory quality of treated water can be achieved, permitting its sustainable reuse in the hydrologic cycle while minimizing environmental and economic impact.