PEG modified column MIL-101(Cr)/PVA cryogel as a sorbent in stir bar solid phase extraction for determination of non-steroidal anti-inflammatory drugs in water samples

Natural deep eutectic solvent-functionalized mesoporous graphitic carbon nitride-reinforced electrospun nanofiber: a promising sorbent in miniaturized on-chip thin film micro-solid-phase extraction prior to liquid chromatography-tandem mass spectrometry for measuring NSAIDs in saliva

To meet the needs of developing efficient extractive materials alongside the evolution of miniaturized sorbent-based sample preparation techniques, a mesoporous structure of g-C3N4 doped with sulfur as a heteroatom was achieved utilizing a bubble template approach while avoiding the severe conditions of other methods. In an effort to increase the number of adsorption sites, the resultant exfoliated structure was then modified with thymol-coumarin NADES as a natural sorbent modifier, followed by introduction into a nylon 6 polymer via an electrospinning process. X-ray diffraction (XRD), Fourier transform infrared (FT-IR) spectroscopy, field-emission scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), and Brunauer-Emmett-Teller (BET) surface area analysis validated S-doped g-C3N4 and composite production. The prepared electrospun fiber nanocomposite, entailing satisfactory processability, was then successfully utilized as a sorbent in on-chip thin film micro-solid-phase extraction of non-steroidal anti-inflammatory drugs (NSAIDs) from saliva samples prior to liquid chromatography-tandem mass spectrometry (LC-MS/MS) analysis. Utilizing a chip device, a thin film μ-SPE coupled with LC-MS/MS analysis yielded promising outcomes with reduced sample solution and organic solvents while extending lifetime of a thin film sorbent. The DES-modified S-doped g-C3N4 amount in electrospun was optimized, along with adsorption and desorption variables. Under optimal conditions, selected NSAIDs were found to have a linear range of 0.05-100.0 ng mL-1 with an R2 ≥ 0.997. The detection limits were ranged between 0.02 and 0.2 ng mL-1. The intra-day and inter-day precisions obtained were less than 6.0%. Relative recoveries were between 93.3 and 111.4%.

Non-steroidal anti-inflammatory drugs (NSAIDs) in the environment: Updates on pretreatment and determination methods

Non-steroidal anti-inflammatory drugs (NSAIDs) are widely used in human and animal health care to reduce persistent inflammation, pain and fever because of their anti-inflammatory, analgesic and antipyretic effects. However, the improper discharge and disposal make it becomes a major contaminant in the environment, which poses a big threat to the ecosystem. For this reason, accurate, sensitive, effective, green, and economic techniques are urgently required and have been rapidly developed in recent years. This review summarizes the advancement of sample preparation technologies for NSAIDs involving solid-phase extraction, solid-phase microextraction, liquid-phase microextraction, QuEChERS, and matrix solid-phase dispersion. Meanwhile, we overview and compare analytical technologies for NSAIDs, including liquid chromatography-based methods, gas chromatography-based methods, capillary electrophoresis, and sensors, particularly the development of liquid chromatography-based methods. Furthermore, we focus on their progress and conduct a comparison between their advantages and disadvantages.

Preparation of a single and reusable biopolymer-based film for the extraction and preconcentration of anti-inflammatory drugs from environmental water samples

One of the main goals of green chemistry is to reduce the use of toxic materials and the generation of hazardous waste, both during method development and in the synthesis of the materials used. Thus, a biodegradable, single and reusable material composed of agarose and multi-walled carbon nanotubes was proposed. The film preparation was carefully optimized in order to obtain a one-piece sorbent, with high extraction efficiency and the possibility of reuse. The film was tested in the simultaneous extraction and preconcentration of three non-steroidal anti-inflammatory drugs (ketorolac, ketoprofen and piroxicam) from environmental water samples. The optimal extraction parameters were as follows: isopropyl alcohol as the activation solvent, a sample pH value of 3.0, extraction time of 30 min, 2.00 mL of acetonitrile as the eluent, an elution time of 5 minutes, and a sample volume of 250.00 mL. Under these conditions, the film was reusable 50 times without losing its extraction capacity significantly. HPLC with a photodiode array detector was used for the separation and determination. The method presented a linear range between 0.10 and 1.2 μg L^-1, good sensitivity with limits of detection between 0.0075 and 0.0089 μg L^-1, and quantification between 0.025 and 0.030 μg L^-1. In addition, low RSD values (0.46-3.13%) were obtained demonstrating satisfactory precision. Stream water samples were analyzed, and recoveries between 82.0 and 109.0% were obtained.

Magnetic Solid-Phase Extraction Based on Magnetite-Multiwalled Carbon Nanotubes of Non-Steroidal Anti-Inflammatories from Water Followed by LC-ESI-MS/MS

An analytical method based on liquid chromatography-electrospray ionization-tandem mass spectrometry detection (LC-ESI-MS/MS) has been developed for the determination of pharmaceutical compounds in water samples. Five non-steroidal anti-inflammatory drugs (NSAIDs) namely Naproxen, Ketoprofen, Piroxicam, Diflunisal and Celecoxib were investigated. Magnetic solid phase extraction (MSPE) was used for sample pre concentration of water samples and magnetic carbon nanotubes (Fe3O4-MWCNTs) were considered as solid phase extraction sorbent. Important parameters influencing the extraction efficiency such as nature and volume of eluent, sample pH and adsorbent mass were optimized. The developed MSPE method involved 75 mg of Fe3O4-MWCNTs sorbent, 5 mL of water sample at pH = 4 and 5 mL of 10% ammonia in methanol in the elution step. Under the optimized extraction conditions, linearity, detection and quantification limits and reproducibility were evaluated. The proposed method was successfully applied to the analysis of NSAIDs in surface waters, and mean recoveries of all the NSAIDs were above 90% with relative standard deviations < 17%. The detection and quantification limits were comprised between 0.05-3.6 ng.mL-1 and 0.2-11.9 ng.mL-1, respectively.

Vortex-assisted supramolecular solvent dispersive liquid–liquid microextraction of ketoprofen and naproxen from environmental water before chromatographic analysis: response surface methodology optimisation

A microextraction procedure that is rapid and simple to extract and preconcentrate ketoprofen and naproxen is proposed. An environmentally friendly supramolecular solvent was applied as an extraction solvent and proved to be efficient in the extraction of ketoprofen and naproxen from environmental water. The design of experiment approach was used to screen, optimize significant parameters, and determine optimum experimental conditions. Under optimized experimental conditions, the vortex-assisted supramolecular solvent dispersive liquid–liquid microextraction provided a good linearity (0.57–700 µg L−1), low limits of detection (0.17–0.24 µg L−1) and extraction reproducibility below 9%. The high percentage relative recoveries (93.6–101.4%) indicated that the method is not affected by matrix. The practical applicability of the method was assessed by analysing ketoprofen and naproxen in river water and effluent wastewater samples. Both analytes were found in effluent wastewater.

Advances in Metal-Organic Frameworks MIL-101(Cr)

MIL-101(Cr) is one of the most well-studied chromium-based metal-organic frameworks, which consists of metal chromium ion and terephthalic acid ligand. It has an ultra-high specific surface area, large pore size, good thermal/chemical/water stability, and contains unsaturated Lewis acid sites in its structure. Due to the physicochemical properties and structural characteristics, MIL-101(Cr) has a wide range of applications in aqueous phase adsorption, gas storage and separation, and catalysis. In this review, the latest synthesis of MIL-101(Cr) and its research progress in adsorption and catalysis are reviewed.

Template Method for Synthesizing Hierarchically Porous MIL-101(Cr) for Efficient Removal of Large Molecular Dye

As one of the most important prototypical chromium-based MOFs, MIL-101(Cr) is well-studied and widely employed in various scientific fields. However, due to its small capture window sizes and curved internal apertures, its application in large molecular removal is quite limited, and given its high stability and high synthetic temperature (>200 °C), it is difficult to achieve hierarchically porous MIL-101(Cr). In our study, hierarchically porous MIL-101(Cr) involving a high macro-/meso-/micropores ratio was designed and synthesized using acetic acid as an additive and silicon dioxide (SiO2) nanoparticles as a template. The optimal hierarchically porous MIL-101(Cr) (A-4) possessed a high specific surface area (2693 m2 g−1) and an abundant macro-/mesoporous structure with the addition of SiO2 of 200 mg. Compared with the control sample (A-0) with a less macro-/mesoporous structure, A-4 showed good adsorption properties for both coomassie brilliant blue R-250 (CBB, 82.1 mg g−1) and methylene blue (MB, 34.3 mg g−1) dyes, which were 1.36 times and 9.37 times higher than those of A-0. Moreover, A-4 also had good recyclability, and the removal rate of CBB was still higher than 85% after five cycles of adsorption.

A hierarchical porous composite magnetic sorbent of reduced graphene oxide embedded in polyvinyl alcohol cryogel for solvent assisted-solid phase extraction of polycyclic aromatic hydrocarbons

A hierarchical porous composite magnetic sorbent was fabricated and applied to the dispersive solvent assisted-solid phase extraction of five polycyclic aromatic hydrocarbons. A sorbent was first prepared by incorporating graphene oxide, calcium carbonate and magnetite nanoparticles into a polyvinyl alcohol cryogel. The graphene oxide was converted to reduced graphene oxide using ascorbic acid and a hierarchical porous structure was produced by reacting hydrochloric acid with incorporated calcium carbonate to generate carbon dioxide bubbles which created a second network. Before extracting the target analytes, extraction solvent was introduced into the hierarchical pore network of the sorbent. The extraction was based on the partition between the analytes and introduced extraction solvent and the adsorption of analytes on reduced graphene oxide. The extraction efficiency was enhanced through π-π and hydrophobic interactions between polycyclic aromatic hydrocarbons and reduced graphene oxide and extraction solvent. The extracted polycyclic aromatic hydrocarbons were determined using HPLC coupled with fluorescence detector. The developed method was applied to extract polycyclic aromatic hydrocarbons in disposable diaper, coffee and tea samples and recoveries from 84.5 to 99.4% were achieved with relative standard deviations below 7%. The developed sorbent exhibited good reproducibility and can be reused for ten cycles. This article is protected by copyright. All rights reserved.

Synthesis of highly porous three-dimensional PVA/GO/ZIF-67 cryogel for the simultaneous treatment of waters contaminated with cadmium (II) and lead (II) heavy metal ions

In this research, PVA/GO/ZIF-67 cryogel as a highly porous three-dimensional polymeric adsorbent was synthesized by freeze-drying method and applied for the simultaneous removal of Cd2+ and Pb2+ ions from contaminated...

Vortex-assisted solid-phase extraction based on metal-organic framework/chitosan-functionalized hydrophilic sponge column for determination of triazine herbicides in environmental water by liquid chromatography-tandem mass spectrometry

In the presented work, MIL-101(Cr) and chitosan were directly embedded on the skeleton of melamine sponge material using a simple and environmentally friendly method. Chitosan acts not only as an adhesive during the preparation of functionalized sponges, but also as an adsorption adjuvant in herbicide detection. Unlike other polymers, chitosan has excellent hydrophilicity and contains numerous adsorption sites; thus, it enables the sponge material to be used for determination of contaminants in an aqueous phase. Scanning electron microscopic (SEM) analysis showed that the coating material was uniformly distributed on the skeleton of melamine sponge. The prepared material was used as a sorbent in a vortex-assisted solid-phase extraction and combined with high performance liquid phase tandem mass spectrometry for the extraction and trace determination of six triazines in water samples (Atraton, Desmetryn, Prometon, Ametryn, Prometryn and Dimethametryn). Several parameters that affect the extraction efficiencies were investigated. Under the optimal conditions (MIL-101(Cr) loading, 150 mg; sample pH, 7; salt concentration, 0%; adsorption time, 3 min; desorption solvent, 1.5 mL acetonitrile; desorption time, 4 min), the proposed method was successfully used in the determination of trace triazines in five real water samples (drinking water, tap water, lake waters and river water), satisfactory recoveries were obtained in the range of 78.9%-118.6%. The limits of detection of the proposed method in detecting triazine herbicides in spiked water samples ranged from 0.014 to 0.045 ng mL^-1.

Amine-functionalized magnetic activated carbon as an adsorbent for preconcentration and determination of acidic drugs in environmental water samples using HPLC-DAD

In the present study, a convenient and highly effective method was developed for the quantification of acidic drugs in wastewater and river water samples. Ultrasonic-assisted magnetic solid phase extraction employing magnetic waste tyre-based activated carbon nanocomposite functionalized with [3-(2-aminoethylamino)propyl]trimethoxysilane as a cost-effective and efficient adsorbent was used for the extraction and preconcentration of acidic drugs (naproxen [NAP], ketoprofen (KET) and diclofenac [DIC]). The quantification of target analytes was achieved by high‐performance liquid chromatography with diode array detector. Under optimum conditions, the detection limit, quantification limit and relative standard deviation obtained for the analytes of interest ranged from 0.38 to 0.76, 1.26 to 2.54 µg L−1 and 2.02 to 4.06%, respectively. The applicability of the developed method was assessed by the spike recovery tests and the relative recoveries proved that the method is reliable for the determination of acidic drugs in wastewater. Thereafter, the method was applied successfully for the determination of NAP, KET and DIC in river water, influent and effluent wastewater.

A flower-like hybrid material composed of Fe3O4, graphene oxide and CdSe nanodots for magnetic solid phase extraction of ibuprofen prior to its quantification by HPLC detection

A flower-like Fe₃O₄/GO/CdSe nanodot magnetic hybrid material was produced and applied to magnetic solid-phase extraction of ibuprofen from pharmaceuticals, water, and urine samples. The material was characterized by X-ray diffraction, Raman spectroscopy and field emission scanning electron microscopy and SEM-EDX. The pH value, volume of sample solution, amount of sorbent, type and volume of elution solvent and extraction time were optimized. Following elution with acetone, ibuprofen was quantified by HPLC-DAD detection. The recoveries of ibuprofen from spiked real samples ranged between 87 and 109%, and the intra-day and inter-day relative standard deviations from 1.25 to 3.02%. The limit of detection, limit of quantification and preconcentration factor are 0.36 ng·mL^-1,1.20 ng·mL^-1 and 150, respectively. Graphical abstract Schematic representation of the combination of flower-like Fe₃O₄/GO/CdSe nanodot-based magnetic solid phase extraction (MSPE) and high-performance liquid chromatography (HPLC) procedure for the extraction and analysis of ibuprofen in pharmaceuticals, water, and urine samples.

Metal–Organic Frameworks as Key Materials for Solid-Phase Microextraction Devices—A Review

Metal–organic frameworks (MOFs) have attracted recently considerable attention in analytical sample preparation, particularly when used as novel sorbent materials in solid-phase microextraction (SPME). MOFs are highly ordered porous crystalline structures, full of cavities. They are formed by inorganic centers (metal ion atoms or metal clusters) and organic linkers connected by covalent coordination bonds. Depending on the ratio of such precursors and the synthetic conditions, the characteristics of the resulting MOF vary significantly, thus drifting into a countless number of interesting materials with unique properties. Among astonishing features of MOFs, their high chemical and thermal stability, easy tuneability, simple synthesis, and impressive surface area (which is the highest known), are the most attractive characteristics that makes them outstanding materials in SPME. This review offers an overview on the current state of the use of MOFs in different SPME configurations, in all cases covering extraction devices coated with (or incorporating) MOFs, with particular emphases in their preparation.