Optical detection and recovery of Yb(III) from waste sample using novel sensor ensemble nanomaterials

Assessment of rare earth elements variations in five water systems in Beijing: Distribution, geochemical features, and fractionation patterns

This study investigates the distribution of rare earth elements (REEs) within the Beijing water system, specifically examining the Yongding, Chaobai, Beiyun, Jiyun, and Daqing rivers. Results indicate that the Beiyun River exhibits the highest REE concentrations, ranging from 35.95 to 59.78 μg/mL, while the Daqing River shows the lowest concentrations, ranging from 15.79 to 17.48 μg/mL. LREEs (La to Nd) predominate with a total concentration of 23.501 μg/mL, leading to a notable LREE/HREE ratio of 7.901. Positive Ce anomalies (0.70-1.11) and strong positive Eu anomalies (1.38-2.49) were observed. The study suggests that the Beijing water system's REEs may originate from geological and anthropogenic sources, such as mining and industrial activities in neighboring regions, including Inner Mongolia. These findings underscore the importance of ongoing monitoring and effective water management strategies to address REE-related environmental concerns.

Assessment of heavy metals accumulation by vegetables irrigated with different stages of textile wastewater for evaluation of food and health risk

Wastewater irrigation for vegetable cultivation is greatly concerned about the presence of toxic metals in irrigated soil and vegetables which causes possible threats to human health. This study aimed to ascertain the accumulation of heavy metals (HMs) in edible parts of vegetables irrigated with different stages of textile dyeing wastewater (TDW). Bio-concentration factor (BCF), Estimated daily intake (EDI), and target hazard quotient (THQ) were computed to estimate human health risks and speculate the hazard index (HI) of adults and children with the consumption of HMs contaminated vegetables at recommended doses. Five vegetables (red amaranth, Indian spinach, cauliflower, tomato, and radish) in a pot experiment were irrigated with groundwater (T1) and seven stages of TDW (T2∼T8) following a randomized complete block design (RCBD) with three replications. Among the TDW stages, T8, T7, T4, and T5 exhibited elevated BCF, EDI, THQ, and HI due to a rising trend in the accumulation of Pb, Cd, Cr, and Ni heavy metals in the edible portion of the red amaranth, followed by radish, Indian spinach, cauliflower, and tomato. The general patterns of heavy metal (HM) accumulation, regarded as vital nutrients for plants, were detected in the following sequence: Zn > Mn/Cu > Fe. Conversely, toxic metals were found to be Cd/Cr > Ni > Pb, regardless of the type of vegetables. Principal Component Analysis (PCA) identified T8, T7, and T4 of TDW as the primary contributors to the accumulation of heavy metals in the vegetables examined. Furthermore, the analysis of the heavy metals revealed that the BCF, THQ, and HI values for all studied metals were below 1, except for Pb. This suggests that the present consumption rates of different leafy and non-leafy vegetables, whether consumed individually or together, provide a low risk in terms of heavy metal exposure. Nevertheless, the consumption of T8, T7, and T4 irrigated vegetables, specifically Indian spinach alone or in combination with red amaranth and radish, by both adults and children, at the recommended rate, was found to pose potential health risks. On the other hand, T2, T3, and T6 irrigated vegetables were deemed safe for consumption. These findings indicated that the practice of irrigating the vegetables with T8, T7, and T4 stages of TDW has resulted in a significant buildup of heavy metals in the soils and edible parts of vegetables which are posing health risks to adults and children. Hence, it is imperative to discharge the T8, T7, and T4 stages of TDW after ETP to prevent the contamination of vegetables and mitigate potential health risks.

Environmental and economic assessments of industry-level medical waste disposal technologies - A case study of ten Chinese megacities

Medical waste (MW) is exploding due to the COVID-19 pandemic, posing a significant environmental threat, and leading to the urgent requirement for affordable and environmentally friendly MW disposal technologies. Prior research on individual MW disposal plants is region-specific, applying these results to other regions may introduce bias. In this study, major MW disposal technologies in China, i.e., incineration technologies (pyrolysis incineration and rotary kiln incineration), and sterilization technologies (steam sterilization, microwave sterilization, and chemical disinfection) with residue landfill or incineration were analyzed from an industry-level perspective via life cycle assessment (LCA), life cycle costing (LCC) and net present value (NPV) methods. Life cycle inventories and economic cost data for 4-5 typical companies were selected from 128 distinct enterprises and academic sources for each technology. LCA results show that microwave sterilization with residue incineration has the lowest environmental impact, emitting only 480 kg CO2 eq. LCC and NPV analyses indicate that steam sterilization with landfilling is the most economical, yielding revenues of 1,210 CNY/t and breaking even in the first year. Conversely, pyrolysis and rotary kiln incineration break even between the 4th and 5th years. Greenhouse gas emissions from the MW disposal in ten cities with the largest MW production in 2020 increased by 7% over 2019 to 43,800 tons and other pollutants increased by 6% to 12%. Economically, Shanghai exhibits the highest cost-effectiveness, while Nanjing delivers the lowest. It can be observed that the adoption of optimal environmental technologies has resulted in a diminution of greenhouse gas emissions by 279,000 tons and energy conservation of 1.76 billion MJ.

CRISPR-Cas12a powered hybrid nanoparticle for extracellular vesicle aggregation and in-situ microRNA detection

Efficient extracellular vesicle (EV) enrichment and timely internal RNA detection for cancer diagnostics are highly desirable and remain a challenge. Here, we report a rapid EV aggregation induced in-situ microRNA detection technology based on cationic lipid-polymer hybrid nanoparticles encapsulating cascade system of catalytic hairpin assembly and CRISPR-Cas12a (CLHN-CCC), allowing for EV enrichment in three-dimensional space and in-situ detection of internal microRNAs in one step within 30 min. The enrichment efficiency (>90%) of CLHN-CCC is demonstrated in artificial EVs, cell-secreted EVs and serum EVs, which is 5-fold higher than that of traditional ultracentrifugation. The sensitive detection of artificial EVs and internal miR-1290 was achieved with the limit of detection of 10 particles/μL and 0.07 amol, respectively. After lyophilization, CLHN-CCC shows no obvious loss of performance within 6 months, making it much more robust and user friendly. This technique could sensitively (sensitivity = 92.9%) and selectively (selectivity = 85.7%) identify low amount miR-1290 in serum EVs, distinguishing early-stage pancreatic cancer patients from healthy subjects, showing high potential for clinical applications.

Changes in microcystin concentration in Lake Taihu, 13 years (2007-2020) after the 2007 drinking water crisis

Since the 2007 water crisis occurred in Lake Taihu, substantial measures have been taken to restore the lake. This study evaluates the effectiveness of these restoration activities. We examined the physicochemical parameters and the distribution of microcystin and Microcystis in both the water column and sediment during the bloom period of May 2020 to October 2020. The mean value of extracellular and intracellular microcystin content was 0.12 μg L-1 and 16.26 μg L-1, respectively. The mean value of microcystin in sediment was 172.02 ng g-1 and peaked in August. The concentration in the water and sediment was significantly lower than the historical average concentration. The abundance of toxigenic Microcystis and total Microcystis in the water column ranged from 2.61 × 102 to 2.25 × 109 copies·L-1 and 8.28 × 105 to 2.76 × 109 copies·L-1, respectively. The proportion of toxic Microcystis in the sediment ranging from 31.2% to 19.12%. The highest and lowest region was Meiliang Bay and Grass-algae type zone, respectively. The copy number of the 16S rRNA gene was 1-4 orders of magnitude higher than that of mcyA gene in populations of Microcystis, indicating that non-toxic Microcystis was the dominant form in the majority of the lake. The abundance of toxic Microcystis in the water column was positively correlated with total phosphorus, PO43--P and pH, while the water temperature played distinct role to the distribution of toxic Microcystis in sediment. Our research indicated phosphorus remains a key factor influencing the toxic Microcystis and microcystins in the water column. pH played distinct roles in the distribution of microcystins in sediment and water column. The increasing water temperature is a threat. Explicit management actions and policies, which take into account nutrient concentrations, pH, and increasing temperatures, are necessary to understand and control the distribution of microcystin and Microcystis in Lake Taihu.

Advancing the development of nanocomposite adsorbent through zinc-doped nickel ferrite-pinecone biochar for removal of chromium (VI) from wastewater

Leather and textile industrial effluents are the main disseminating routes for chromium contamination of water bodies, causing adverse impacts on public and environmental health. The attempt to remediate chromium through conventional wastewater treatment methods is inefficient. Therefore, this study aims to synthesize zinc-doped nickel ferrite pinecone biochar (Zn-NiF@PBC) nanocomposite for the removal of chromium from wastewater systems. The Zn-NiF@PBC nanocomposite was synthesized via the co-precipitation method. The properties of zinc-doped nickel ferrite (Zn-NiF) were effectively modified by blending with biochar at 1, 5, 10, and 15 % (w/w) which was successfully embedded with Zn-Ni ferrite nanoparticles. This was characterized and confirmed by typical adsorbent properties such as a high surface area of 104 m2/g, conducive pore volume of 0.117 cm3/g and pore size of 3.41 nm (BET), interactive multi-functional groups (FTIR), surface charge determination (pHpzc,), crystalline structure (XRD) and very rough surface morphology (SEM). The maximum chromium adsorption was found to be 95 % at the specific experimental condition of pH 3, adsorbent dose 1 g/50 mL, contact time 120 min, and initial chromium concentration 100 mg/L. The adsorption experimental data was best fitted with the Langmuir isotherm at R2 0.98 indicating the adsorption process was homogeneous and monolayer whereas the kinetics adsorption was resembling the second-order kinetic at R2 0.99. Moreover, the adsorption thermodynamics was spontaneous, endothermic, and increased the change in entropy. Finally, the regeneration of Zn-NiF@PBC was found to be effective up to five 5 cycles but gradually degrading in terms of removal efficiency after 3 cycles. In general, Zn-NiF@PBC can remediate chromium from wastewater with huge potential for scale-up and extend to other pollutants clear-up.

Preparation of chitosan-iron oxide modified sludge-based biochar for effective removal of tetracycline from water: performance and mechanism

The release of antibiotics has attracted wide attention due to their abuse and discharge. How to remove these emerging contaminants is an urgent need to be solved. In the present study, sludge-based biochar combining chitosan and iron oxide was prepared via municipal sewage sludge. The novel biochar modified with chitosan and iron oxide exhibited satisfying performance in eliminating antibiotics from water. The application of modified biochar combined with activated persulfate (PS) showed a remarkable removal efficiency of 96.98% for tetracycline (TC). Analysis of the surface characteristics of the modified biochar showed the presence of structural defects, dispersed iron oxides, abundant functional groups, a porous structure, and a relatively stable crystal structure. These characteristics attributed significant importance to facilitating the degradation of TC. A series of experimental conditions including preparation temperature (600-900 ℃), reaction temperature (15-45 ℃), contaminant concentration (30-180 mg/L), adsorbent usage (0.1-1 g/L), pH (2-10), and persulfate addition concentration (1-5 mmol) were conducted. The results revealed that the highest removal efficiency was achieved at 96.98% under the conditions of TC concentration at 30 mg/L, reaction temperature at 35 ℃, pH of 4, adsorbent addition amount of 0.6 g/L, and PS concentration of 2 mmol, respectively. Three degradation pathways and seven intermediate products of TC were proposed. Therefore, our study provides a promising approach for developing effective removal of antibiotic pollutants.

Co-exposure of heavy metals in rice and corn reveals a probabilistic health risk in Guizhou Province, China

The adverse effects of heavy metals have arousing concern in the high geological background area, especially in southwestern Guizhou, China. However, the pollution status of heavy metals are still unclear when exposed to rice and corn in Guizhou province. Therefore, the concentration, pollution level, spatial distribution, and probabilistic health risks of Ni, Cr, Pb, Cu, and Zn are estimated in rice and corn. A total of 241 samples (117 for rice and 124 for corn) were collected from Guizhou province and measured by a method of inductively coupled plasma-mass spectrometry (ICP-MS). The results showed that rice and corn were contaminated with Ni and Cr. High concentrations of Ni were presented in the southeast of rice. It indicated that 22.0 % of rice samples were contaminated with Ni. HI values for children and adults exceeded 1.0 in rice and corn, suggesting that humans might be subject to probabilistic non-carcinogenic risks. FTCR demonstrated that rice and corn might cause probabilistic carcinogenic risks to children and adults, which were both greatly higher than 1.0 × 10-4. Moreover, the contributions of Ni to the HI and FTCR were the highest for adults and children. Therefore, more attention should be paid to the exposure of heavy metals in rice and corn, especially in Ni. The results would provide a novel prospective for pollution control and be helpful for environmental regulation.

Nano-Structural Superwetting Surfaces for Highly Reliable On-Site Detection of Bisphenol A

In the domain of big data geographic screening for environmental pollutants, the expeditious dissemination of testing results to environmental investigation professionals is pivotal in facilitating comprehensive analysis and the implementation of more efficacious strategies for managing environmental issues. However, this endeavor can prove to be particularly arduous when conducting examinations in remote, resource-scarce rural areas and field environments, where deficient infrastructure often emerges as the principal impediment to unimpeded environmental monitoring. Therefore, the development of a reliable and portable monitoring strategy with the ability to analyze large amounts of data is highly required. Here, a deep-learning (DL)-assisted portable sensing strategy was developed based on thermal and pH dual-responsive nano-structural superwetting surfaces, for highly reliable, quick, and field monitoring of environmental pollutants. In our experiment, bisphenol A (BPA) was selected as the representative pollute. The achieved limit of detection, attaining a remarkably low value of 1.05 μM, unequivocally adhered to stringent international testing standards for evaluating the migration of BPA in thermal paper. Based on a DL image classification algorithm, highly precise predictions regarding the migration of BPA concentration were achieved, with an accuracy rate exceeding 99%. Furthermore, it successfully facilitated automated and exceedingly reliable monitoring of the migration of BPA from thermal paper within the principal provinces of thermal paper production in China. This strategy engenders the potential to establish correlations between environmental pollutant concentrations in specific regions and the prevalence of certain human ailments.

Investigating the effect of type of fish and different cooking methods on the residual amount of polycyclic aromatic hydrocarbons (PAHs) in some Iranian fish: A health risk assessment

The aim of this study was to assess the level of PAHs and associated health risks in different types of fish cooked with different methods, using the MSPE-GC/MS technique (magnetic solid phase extraction with gas chromatography/mass spectrometry). The limits of detection (LODs), limits of quantification (LOQs) and recovery percentages ranged from 0.1 to 0.63 μg/kg, 0.3-1.89 μg/kg, and 93.7 to 102.6%, respectively. The results showed that the mean of ƩPAHs in all samples was 20.31 ± 6.60 µg/kg. Additionally, PAH4 and BaP levels in all samples were 4.58 ± 1.40 and 1.08 ± 0.36 µg/kg, respectively, which were below the European Union (EU) standard level (12 and 2 µg/kg, respectively). The results showed that among 5 types of fish, starry sturgeon had highest average total PAHs (13.24 ± 1.84 µg/kg), while Caspian Sea sprat had the lowest average total PAHs (1.24 ± 0.8 µg/kg). In terms of cooking methods (charcoal-grilled fish, fried fish and oven-grilled fish), charcoal-grilled fish had the highest average total PAH level at 25.41 ± 7.31 µg/kg, while the lowest average total PAH was found in the raw fish sample at 16.44 ± 4.63 µg/kg. The Monte Carlo Simulation was used to determine the 95% ILCRs (Incremental Lifetime Cancer Risk) due to ingestion of fish. The results showed that the ILCR for adults was 2.85E-9, while for children it was 1.32E-8. Therefore, based on these findings, it can be concluded that the consumption of fish cooked with different methods does not pose a risk to human health in terms of the amount of PAHs (ILCR < 1 × 10-4).

Current trends in the detection and removal of heavy metal ions using functional materials

The shortage of freshwater resources caused by heavy metal pollution is an acute global issue, which has a great impact on environmental protection and human health. Therefore, the exploitation of new strategies for designing and synthesizing green, efficient, and economical materials for the detection and removal of heavy metal ions is crucial. Among the various methods for the detection and removal of heavy ions, advanced functional systems including nanomaterials, polymers, porous materials, and biomaterials have attracted considerable attention over the past several years due to their capabilities of real-time detection, excellent removal efficiency, anti-interference, quick response, high selectivity, and low limit of detection. In this tutorial review, we review the general design principles underlying the aforementioned functional materials, and in particular highlight the fundamental mechanisms and specific examples of detecting and removing heavy metal ions. Additionally, the methods which enhance water purification quality using these functional materials have been reviewed, also current challenges and opportunities in this exciting field have been highlighted, including the fabrication, subsequent treatment, and potential future applications of such functional materials. We envision that this tutorial review will provide invaluable guidance for the design of functional materials tailored towards the detection and removal of heavy metals, thereby expediting the development of high-performance materials and fostering the development of more efficient approaches to water pollution remediation.

High-efficiency foam fractionation of anthocyanin from perilla leaves using surfactant-free active Al2O3 nanoparticle as collector and frother: Performance and mechanism

Anthocyanin (ACN) is a natural pigment with significant industrial applications. However, foam fractionation of ACN from perilla leaves extract presents theoretical challenges due to its limited surface activity and foaming capacity. This work developed a surfactant-free active Al₂O₃ nanoparticle (ANP) as a collector and frother, which was modified with adipic acid (AA). The ANP-AA efficiently collected ACN through the electrostatic interaction, condensation reaction, and hydrogen bonding, with a Langmuir maximum capacity of 129.62 mg/g. Moreover, ANP-AA could form a stable foam layer by irreversibly adsorbing on the gas-liquid interface, reducing surface tension, and alleviating liquid drainage. Under the appropriate conditions of ANP-AA 400 mg/L and pH 5.0, we achieved a high ACN recovery of 95.68% with an enrichment ratio of 29.87 after ultrasound-assisted extraction of ACN from perilla leaves. Additionally, the recovered ACN displayed promising antioxidant properties. These findings hold significant importance in the food, colorant, and pharmaceutical industries.

Phenanthrene sorption studies on coffee waste- and diatomaceous earth-based adsorbents, and adsorbent regeneration with cold atmospheric plasma

Phenanthrene (PHE) is a polycyclic aromatic hydrocarbon categorized as a high priority organic pollutant being toxic for the ecosystem and human health, and its sorption on natural organic or inorganic substances seems a well-promising method for its removal from water streams. The goals of the present work are (i) to assess the capacity of low-cost adsorbents fabricated by treating coffee wastes and diatomaceous earth to remove PHE from water; (ii) to elucidate the role of the pore structure on PHE sorption dynamics; and (iii) to assess the potential to regenerate adsorbents loaded with PHE, by using the novel technology of cold atmospheric plasma (CAP). Diatomaceous earth (DE) and DE pre-treated with sodium hydroxide (NaOH) or phosphoric acid (H₃PO₄) were chosen as inorganic adsorbents. Coffee waste (CW) and activated carbons (AC) produced from its pyrolysis at 800 °C (CWAC), either untreated (CWAC-800) or pre-treated with NaOH (CWAC-NaOH-800) and H₃PO₄ (CWAC-H₃PO₄-800), were chosen as organic adsorbents. The adsorbents were characterized with nitrogen adsorption-desorption isotherms, attenuated total reflectance-Fourier transform infrared spectroscopy, Raman spectroscopy, scanning electron microscopy, and mercury intrusion porosimetry. Based on the PHE sorption capacity and pore structure/surface characteristics, the CWAC-NaOH-800 was chosen as the most efficient adsorbent for further equilibrium and kinetic sorption studies. The multi-compartment model was used to describe the PHE sorption dynamics in CWAC-NaOH-800 by accounting for the pore/surface diffusion and instantaneous sorption. The CWAC-NaOH-800 exhibited remarkable values for (i) the specific surface area (S_BET = 676.5 m²/g) and meso- and micro-pore volume determined by nitrogen sorption (V_LN2 = 0.415 cm³/g); (ii) the macro- and meso-pore volume determined by mercury intrusion porosimetry (V_MIP = 3.134 cm³/g); and (iii) the maximum PHE sorption capacity (q_max = 142 mg/g). The percentage of adsorbent recovery after its regeneration with CAP was found to be ~ 35%. From the simulation of sorption dynamics, it was found that at early times, the sorption kinetics is governed by the film diffusion towards the external surface of grains, but at late times, most of the adsorbed mass is transferred primarily to meso-/macro-pores via diffusion, and secondarily to micro-porosity via surface diffusion. Based on the adsorbent characteristics, effect of pH on sorption efficiency, and numerical analysis of sorption dynamics, it was concluded that probably the dominant adsorption mechanism is the π-π interactions between hydrophobic PHE aromatic rings and CWAC-NaOH-800 graphene layers. The high PHE removal efficiency of CWAC-NaOH-800, the successful interpretation of sorption dynamics with the multi-compartment model, and the potential to regenerate PHE-loaded adsorbents with the green and economic technology of CAP motivate a strategy for testing CWACs towards the adsorption of other PAHs, application of adsorbents to real wastewaters, and scaling-up to pilot units.

Alkali-oxygen cooking coupled with ultrasonic etching for directly defibrillation of bagasse parenchyma cells into cellulose nanofibrils

A scheme combining alkali‑oxygen cooking and ultrasonic etching cleaning was developed for the short range preparation of CNF from bagasse pith, which has a soft tissue structure and is rich in parenchyma cells. This scheme expands the utilization path of sugar waste sucrose pulp. The effect of NaOH, O₂, macromolecular carbohydrates, and lignin on subsequent ultrasonic etching was analyzed, and it was found that the degree of alkali‑oxygen cooking was positively correlated with the difficulty of subsequent ultrasonic etching. The mechanism of ultrasonic nano-crystallization was found to be the bidirectional etching mode from the edge and surface cracks of the cell fragments by ultrasonic microjet in the microtopography of CNF. The optimum preparation scheme was obtained under the condition of 28 % NaOH content and 0.5 MPa O₂, which solves the problem of low-value utilization of bagasse pith and environmental pollution, providing a new possibility for the source of CNF.

Effective Adsorption and Removal of Doxorubicin from Aqueous Solutions Using Mesostructured Silica Nanospheres: Box-Behnken Design Optimization and Adsorption Performance Evaluation

The aim of this study is to evaluate the efficacy of mesoporous silica nanospheres as an adsorbent to remove doxorubicin (DOX) from aqueous solution. The surface and structural properties of mesoporous silica nanospheres were investigated using BET, SEM, XRD, TEM, ζ potential, and point of zero charge analysis. To optimize DOX removal from aqueous solution, a Box-Behnken surface statistical design (BBD) with four times factors, four levels, and response surface modeling (RSM) was used. A high amount of adsorptivity from DOX (804.84 mg/g) was successfully done under the following conditions: mesoporous silica nanospheres dose = 0.02 g/25 mL; pH = 6; shaking speed = 200 rpm; and adsorption time = 100 min. The study of isotherms demonstrated how well the Langmuir equation and the experimental data matched. According to thermodynamic characteristics, the adsorption of DOX on mesoporous silica nanospheres was endothermic and spontaneous. The increase in solution temperature also aided in the removal of DOX. The kinetic study showed that the model suited the pseudo-second-order. The suggested adsorption method could recycle mesoporous silica nanospheres five times, with a modest reduction in its ability for adsorption. The most important feature of our adsorbent is that it can be recycled five times without losing its efficiency.

Tailoring abundant active-oxygen sites of Prussian blue analogues-derived adsorbents for highly efficient Yb(III) capture

The removal of rare earth elements in mineral processing wastewater is highly desirable but still challenging. In this study, three bimetallic Prussian blue analogues (PBA) and six corresponding oxides are prepared by co-precipitation and calcination methods, and then utilized to adsorb aqueous Yb(III) solution. The results of XRD, SEM, BET, and XPS indicate the successful synthesis of all the adsorbents. Among them, three PBA-oxide samples (PBO-800) exhibit the superior adsorption capacities (˃250 mg/g). The adsorption processes of Yb(III) are in accordance with the pseudo-second-order kinetic model and Langmuir model, simultaneously showing the spontaneous and endothermic thermodynamics. Moreover, PBO-800 can be reused after alkaline solution regeneration with less than 10% degradation after five consecutive adsorption-desorption cycles. More importantly, PBO-800 exhibits the impressive separation selectivity of Yb(III) and most light rare earth ions (e.g., 5.51 of Yb/La, 4.03 of Yb/Pr), as well as the selectivity of Yb(III) and alkali metal ions (e.g., 300.5 of Yb/Na, 256.2 of Yb/Ca). According to the characterization analysis and DFT calculation, the adsorption mechanism of Yb(III) by PBO-800 is mainly attributed to the strong interaction between the abundant active-oxygen sites and Yb(III), and the significant electrostatic attraction.

Enhanced Adsorption and Evaluation of Tetracycline Removal in an Aquatic System by Modified Silica Nanotubes

In the present study, a nanocomposite adsorbent based on mesoporous silica nanotubes (MSNTs) loaded with 3-aminopropyltriethoxysilane (3-APTES@MSNTs) was synthesized. The nanocomposite was employed as an effective adsorbent for the adsorption of tetracycline (TC) antibiotics from aqueous media. It has an 848.80 mg/g maximal TC adsorption capability. The structure and properties of 3-APTES@MSNT nanoadsorbent were detected by TEM, XRD, SEM, FTIR, and N₂ adsorption-desorption isotherms. The later analysis suggested that the 3-APTES@MSNT nanoadsorbent has abundant surface functional groups, effective pore size distribution, a larger pore volume, and a relatively higher surface area. Furthermore, the influence of key adsorption parameters, including ambient temperature, ionic strength, initial TC concentration, contact time, initial pH, coexisting ions, and adsorbent dosage, had also been investigated. The 3-APTES@MSNT nanoadsorbent's ability to adsorb the TC molecules was found to be more compatible with Langmuir isothermal and pseudo-second-order kinetic models. Moreover, research on temperature profiles pointed to the process' endothermic character. In combination with the characterization findings, it was logically concluded that the 3-APTES@MSNT nanoadsorbent's primary adsorption processes involved interaction, electrostatic interaction, hydrogen bonding interaction, and the pore-fling effect. The synthesized 3-APTES@MSNT nanoadsorbent has an interestingly high recyclability of >84.6 percent up to the fifth cycle. The 3-APTES@MSNT nanoadsorbent, therefore, showed promise for TC removal and environmental cleanup.

Efficient Removal of Basic Fuchsin from Synthetic Medical Wastewater and Competitive Adsorption in the Mixture

The Ziehl-Neelsen stain is a mixture of Basic Fuchsin (BF), phenol (Ph), and methylene blue. It is used to stain the cell walls of Mycobacterium species. In this study, Basic Fuchsin was efficiently removed from synthetic wastewater using natural clay of Gankawa (GC) from Sulaimanyah city, and the effect of the presence of high concentrations of phenol in the adsorption mixture is demonstrated. In addition, X-ray diffraction (XRD), X-ray fluorescence (XRF), N2 gas adsorption analyzer, and field-emission scanning electron microscopy (FESEM) were used to characterize the natural clay. The clay was found to be mostly calcite, with a minor percentage of smectite, and contaminated with low percentages of illite. The adsorption kinetics show a relatively fast equilibration time (60-70 minutes). A second-order pseudokinetic model better fits the experimental kinetic data. The effect of the initial pH of the solution mixture was negligible at the experimental concentration range of the study. Freundlich and Langmuir’s adsorption isotherm models were applied to the equilibrium experimental data using nonlinear regression curve fitting. Both kinetics and isotherm studies point to a chemical adsorption mechanism for the process. For adsorption in the mixture, phenol molecules were found to compete with BF molecules for the active adsorption sites, while a synergetic effect of BF exists on phenol adsorption. As a naturally abundant cheap material, GC shows a superior adsorption capacity toward BF (287.0 mg g-1) over all natural materials and most of the synthetic or modified materials found in the literature.

Efficient Removal of Ciprofloxacin from Contaminated Water via Polystyrene Anion Exchange Resin with Nanoconfined Zero-Valent Iron

Ciprofloxacin (CIP), an important emerging contaminant, has been frequently detected in water, and its efficient removal has become an issue of great concern. In this study, a nanocomposite material nZVI/PA was synthesized by impregnating nanoscale zero-valent iron (nZVI) inside a millimeter-sized porous host (polystyrene-based anion exchange resin (PA)) for CIP removal. The nZVI/PA composite was characterized by field emission scanning electron microscopy coupled with energy-dispersive X-ray, transmission electron microscopy, X-ray diffraction, as well as X-ray photoelectron spectroscopy, and it was confirmed that nZVI was uniformly dispersed in PA with a small particle size. Furthermore, several key factors were investigated including initial solution pH, initial CIP concentration, co-existing ions, organic ligands, and dissolved oxygen. The experimental results indicated that the nZVI/PA composites exhibited a high removal efficiency for CIP under the conditions of initial pH 5.0, and initial CIP concentration 50 mg L^-1 at 25 °C, with the maximum removal rate of CIP reaching 98.5%. Moreover, the nZVI/PA composites exhibited high efficiency even after five cycles. Furthermore, quenching tests and electron spin resonance (ESR) confirmed that CIP degradation was attributed to hydroxyl (·OH) and superoxide radicals (⋅O2-). Finally, the main degradation products of CIP were analyzed, and degradation pathways including the hydroxylation of the quinolone ring, the cleavage of the piperazine ring, and defluorination were proposed. These results are valuable for evaluating the practical application of nZVI/PA composites for the removal of CIP and other fluoroquinolone antibiotics.

An Experimental Investigation of the Mechanical Behavior and Particle Crushing Characteristic of Volcanic Soil

Volcanic soil is a special soil that is well-known for its distinctive texture, vesicular nature, and particle fragility. The fragility characteristic of volcanic soil is the main factor affecting the foundation stability in road engineering. This study focuses on the mechanical properties and particle crushing characteristics of volcanic soil retrieved from Northeast China. A series of triaxial consolidation and drainage shear tests are performed on volcanic coarse-grained soil (5 mm > d > 0.075 mm) under different initial relative densities and effective confining pressures. Results show the peak friction angle of volcanic soil significantly decreases with the increase of confining pressure. The particle crushing degree of volcanic soil increases with the increase of confining pressure, particle size, and relative density. The relative breakage rate of the same particle size group has a good linear relationship with a fractal dimension. Moreover, for the same particle size, the relationship between plastic work and relative breakage rate can be fitted by a power function, which is not significantly affected by relative density or effective confining pressure. From an engineering view, in addition to increasing the compaction degree of volcanic soil, volcanic soil with fine particles used as a roadbed filler can significantly reduce the deformation of the roadbed and improve the bearing capacity of the foundation.

A novel sensor for the selective monitoring of trace ytterbium ions using an agarose-based optical membrane

A novel highly selective sensitive optical sensor was prepared via the chemical immobilization of β-2-hydroxybenzyl-5-bromo-2-hydroxyazastyrene (HBBHAS) on an epoxy-activated agarose membrane pieces. The absorbance variation of the immobilized azastyrene film on agarose upon the addition of 1.5 × 10⁻⁵ M aqueous solutions of La³⁺, Y³⁺, Al³⁺, Sc³⁺, Sm³⁺, Eu³⁺, Lu³⁺, Fe³⁺, Ce³⁺, Cr³⁺, S₂O₃²⁻, Tb³⁺, Mn²⁺ and KIO₃ revealed substantially higher changes for the Yb³⁺ ion compared to the other considered ions. Thus, using HBBHAS as an appropriate ionophore, a selective optical sensor for Yb³⁺ was prepared via its chemical immobilization on a transparent agarose membrane. The effects of pH, reagent concentration, and time duration of the reaction of immobilizing the reagent were examined. A distinct change in the maximum absorbance of the reagent was established on contact of the sensing membrane with Yb³⁺ ions at pH = 4.25. For the membrane sensor, a linear relationship was observed between the variation in membrane absorbance (ΔA) at 424 nm and Yb³⁺ concentrations in the range of 4.75 × 10⁻⁵ to 6.20 × 10⁻¹⁰ M with a detection limit of 1.9 × 10⁻¹⁰ M for Yb³⁺. The effects of some potentially interfering ions on the assessment of Yb³⁺ were analyzed, and no substantial interference was found. The sensor showed a short response time and decent durability with no reagent leaching. The recovery of Yb³⁺ ions from the sensor material was performed using 0.3 M HNO₃ and its response was reversible and reproducible with RSD ≥ 1.95%. This study reports a non-toxic, economical, stable, accurate, easy-to-use, and novel optical sensor material to assess Yb³⁺ in synthetic and environmental water samples.

The immobilized optical sensor preparation and its measurement procedure.

Functionalized layered double hydroxides composite bio-adsorbent for efficient copper(II) ion encapsulation from wastewater

In this study, naturally abundant and inexpensive bamboo was used to make cheaper activated charcoal for efficient encapsulation of toxic copper (Cu(II)) ion from wastewater. The functionalized bamboo charcoal-Layered double hydroxides (BC-LDHs) composite bio-adsorbent was prepared using co-precipitation method. The composite bio-adsorbent was exploited to eliminate Cu(II) ion with high sensitivity and selectivity from contaminated water. The adsorption parameters including the effect of pH, contact time, adsorbent dose, and effect of initial concentration were optimized in systematic way and the adsorption kinetics and isotherms were investigated for potential use in real sample treatment. The physicochemical properties and morphological structure of the adsorbent were examined using X-ray Diffraction, Scanning Electronic Microscopy, Fourier Transform Infrared Spectroscopy and Thermogravimetric Analysis to understand the Cu(II) ion adsorption mechanism. The adsorption results revealed that the BC-LDH could remove almost 100% of Cu(II) ion from aqueous solution at pH range between 3.0 and 6.0 within 30 min. The maximum monolayer adsorption capacity was determined to be 85.47 mg/g based on the Langmuir isotherm. The adsorption equilibrium data were well-fitted by the Langmuir isotherm model (R² = 0.998) and the experimental kinetic data were supported by the pseudo-second order model (R² = 0.999). The BC-LDH could be reused without losing its adsorption performance in several cycles after successful regeneration with 0.10 M HCl. The Cu(II) ion removal mechanism was postulated with intercalated ion exchange, surface precipitation and interaction between BC-LDH and surface functionalities. Therefore, the highly functional BC-LDH composite could be a promising adsorbent for efficient Cu(II) ion removal from wastewater.

Novel micro-structured carbon-based adsorbents for notorious arsenic removal from wastewater

The contamination of groundwater by arsenic (As) in Bangladesh is the biggest impairing of a population, with a large number of peoples affected. Specifically, groundwater of Gangetic Delta is alarmingly contaminated with arsenic. Similar, perilous circumstances exist in many other countries and consequently, there is a dire need to develop cost-effective decentralized filtration unit utilizing low-cost adsorbents for eliminating arsenic from water. Morphological synthesis of carbon with unique spherical, nanorod, and massive nanostructures were achieved by solvothermal method. Owing to their intrinsic adsorption properties and different nanostructures, these nanostructures were employed as adsorption of arsenic in aqueous solution, with the purpose to better understanding the morphological effect in adsorption. It clearly demonstrated that carbon with nanorods morphology exhibited an excellent adsorption activity of arsenite (about 82%) at pH 3, remarkably superior to the two with solid sphere and massive microstructures, because of its larger specific surface area, enhanced acid strength and improved adsorption capacity. Furthermore, we discovered that iron hydroxide radicals and energy-induced contact point formation in nanorods are the responsible for the high adsorption of As in aqueous solution. Thus, our work provides insides into the microstructure-dependent capability of different carbon for As adsorption applications.