A molecularly imprinted electrochemical BPA sensor based on multi-walled carbon nanotubes modified by CdTe quantum dots for the detection of bisphenol A

A Facile Electrode Modification Approach Based on Metal-Free Carbonaceous Carbon Black/Carbon Nanofibers for Electrochemical Sensing of Bisphenol A in Food

Bisphenol A (BPA) is a typical environmental estrogen that is distributed worldwide and has the potential to pose a hazard to the ecological environment and human health. The development of an efficient and sensitive sensing strategy for the monitoring of BPA residues is of paramount importance. A novel electrochemical sensor based on carbon black and carbon nanofibers composite (CB/f-CNF)-assisted signal amplification has been successfully constructed for the amperometric detection of BPA in foods. Herein, the hybrid CB/f-CNF was prepared using a simple one-step ultrasonication method, and exhibited good electron transfer capability and excellent catalytic properties, which can be attributed to the large surface area of carbon black and the strong enhancement of the conductivity and porosity of carbon nanofibers, which promote a faster electron transfer process on the electrode surface. Under the optimized conditions, the proposed CB/f-CNF/GCE sensor exhibited a wide linear response range (0.4-50.0 × 10-6 mol/L) with a low limit of detection of 5.9 × 10-8 mol/L for BPA quantification. Recovery tests were conducted on canned peaches and boxed milk, yielding satisfactory recoveries of 86.0-102.6%. Furthermore, the developed method was employed for the rapid and sensitive detection of BPA in canned meat and packaged milk, demonstrating comparable accuracy to the HPLC method. This work presents an efficient signal amplification strategy through the utilization of carbon/carbon nanocomposite sensitization technology.

Advances on chalcogenide quantum dots-based sensors for environmental pollutants monitoring

Water contamination represents a significant ecological impact with global consequences, contributing to water scarcity worldwide. The presence of several pollutants, including heavy metals, pharmaceuticals, pesticides, and pathogens, in water resources underscores a pressing global concern, prompting the European Union (EU) to establish a Water Watch List to monitor the level of these substances. Nowadays, the standard methods used to detect and quantify these contaminants are mainly liquid or gas chromatography coupled with mass spectrometry (LC/GC-MS). While these methodologies offer precision and accuracy, they require expensive equipment and experienced technicians, and cannot be used on the field. In this context, chalcogenide quantum dots (QDs)-based sensors have emerged as promising, user-friendly, practical, and portable tools for environmental monitoring. QDs are semiconductor nanocrystals that possess excellent properties, and have demonstrated versatility across various sensor types, such as fluorescent, electrochemical, plasmonic, and colorimetric ones. This review summarizes recent advances (2019-2023) in the use of chalcogenide QDs for environmental sensing, highlighting the development of sensors capable of detect efficiently heavy metals, anions, pharmaceuticals, pesticides, endocrine disrupting compounds, organic dyes, toxic gases, nitroaromatics, and pathogens.

Target-regulated photoactivities of CdS/Ni-MOF heterojunction with [Ru(bpy)2dppz]2+ intercalator: a bisphenol A photoelectrochemical aptasensor

Bisphenol A (BPA), an important endocrine disrupting compound, has infiltrated human daily lives through electronic devices, food containers, and children's toys. Developing of novel BPA assay methods with high sensitivity holds tremendous importance in valuing the pollution state. Here, we constructed an ultrasensitive photoelectrochemical (PEC) aptasensor for BPA determination by regulating photoactivities of CdS/Ni-based metal-organic framework (CdS/Ni-MOF) with [Ru(bpy)2dppz]2+ sensitizer. CdS/Ni-MOF spheres exhibited excellent photocatalytic performance, serving as a potential sensing platform for the construction of target recognition process. [Ru(bpy)2dppz]2+ were embedded into DNA double-stranded structure, functioning as sensitizer for modulating the signal response of the developed PEC aptasensor. The proposed PEC sensor exhibited outstanding analytical performances, including a wide linear range (0.1 to 1000.0 nM), low detection limit (0.026 nM, at 3σ/m), excellent selectivity, and high stability. This work provides a perspective for the design of ideal photosensitive materials and signal amplification strategies and extends their application in environment analysis.

Monolithic 3D structural-substrate SERS sensing platform for ultrasensitive and highly-specific analysis of trace bisphenol A

Constructing advanced substrates with excellent features is promising for sensitive surface-enhanced Raman spectroscopy (SERS) detection. Here a novel capillary monolithic 3D structural-substrate SERS platform with Au@cDNA@Ag@Cyanine 3-aptamer nanoparticles (Au@cDNA@Ag@Cy3-Apt NPs) was fabricated for rapid, highly specific profiling of ultra-trace Bisphenol A (BPA). The proposed SERS platform combined both in-capillary SERS and aptamer-affinity recognition strategies, in which the superior SERS properties of Au-Ag NPs, aptamer selectivity, and the advantages of capillary monolith were integrated. A 3D hierarchically porous network was constructed in the monolithic column, which was endowed with rich hotspots for SERS, rapid sample permeation, and better analysis efficiency than most plane-shaped SERS modes. By varying the amount of Ag+ precursor, the Ag-shell thickness on SERS was finely tuned to guarantee Cy3 label in proximity to the plasmonic surface. Based on the biorecognition of aptamer, the selective identification of BPA occurred and exhibited a significant change in SERS intensity without obvious interference. As a result, the monolithic SERS platform featured facile operation, excellent specificity, and rapid analysis (10 min, much less than the solution-based or planar substrate SERS modes). Ultra-high sensitivity and robust reproducibility for BPA analysis was achieved with a low limit of detection (LOD) at 9.12 × 10-4 ng/L. The feasibility of this SERS platform for monitoring BPA in water and milk samples was also validated. This work lights a new access to capillary monolithic SERS-sensing platform for ultrasensitive and specific analysis of BPA.

Advances in optical and electrochemical sensing of bisphenol a (BPA) utilizing microfluidic Technology: A mini perspective

Continuous exposure to toxic pollutants highlights the need for sensitive detection technologies that can be rapidly applied in the current world for quick screening of real samples. Bisphenol A (BPA) is one of the most common environmental contaminants, and it has the potential to harm both the environment and human health, notably causing reproductive disorders, cancer, heart disease, infertility, mental disorders, etc. Thus, significant attention has been paid to the detection of BPA and microplastics to promote food safety, environmental health, and human health on a sustainable earth. Among the current technologies, microfluidic based systems have garnered a lot of interest as future diagnostic tools for healthcare applications. Microfluidic devices can be deployed for quick screening and real-time monitoring, with inherent advantages like portability, miniaturisation, highly sensing tool and ease of integration with various detection systems. Optical and electrochemical sensors are two major analytical tools found in almost all microfluidic-based devices for ultrasensitive BPA and microplastics determination. In this review, we have evaluated and discussed microfluidic-based detection methods for BPA and microplastics.

An Overview to Molecularly Imprinted Electrochemical Sensors for the Detection of Bisphenol A

Bisphenol A (BPA) is an industrial chemical used extensively in plastics and resins. However, its endocrine-disrupting properties pose risks to human health and the environment. Thus, accurate and rapid detection of BPA is crucial for exposure monitoring and risk mitigation. Molecularly imprinted electrochemical sensors (MIES) have emerged as a promising tool for BPA detection due to their high selectivity, sensitivity, affordability, and portability. This review provides a comprehensive overview of recent advances in MIES for BPA detection. We discuss the operating principles, fabrication strategies, materials, and methods used in MIES. Key findings show that MIES demonstrate detection limits comparable or superior to conventional methods like HPLC and GC-MS. Selectivity studies reveal excellent discrimination between BPA and structural analogs. Recent innovations in nanomaterials, novel monomers, and fabrication techniques have enhanced sensitivity, selectivity, and stability. However, limitations exist in reproducibility, selectivity, and stability. While challenges remain, MIES provide a low-cost portable detection method suitable for on-site BPA monitoring in diverse sectors. Further optimization of sensor fabrication and characterization will enable the immense potential of MIES for field-based BPA detection.

Sensitivity and reusability of a simple microbial fuel cell-based sensor for detecting bisphenol A in wastewater

Polycarbonate plastic processing wastewater contains high concentrations of bisphenol A (BPA), requiring a real-time technology to monitor wastewater containing BPA. Since the activity of electrogenic microorganisms on the anode surface of the microbial fuel cell (MFC) sensor is inhibited by exposure to contaminants, the toxicity of contaminants in wastewater can be determined by observing the variation in voltage output from the MFC sensor. The simple MFC sensor that is developed in this work exhibited a significant decrease in voltage output in BPA-containing wastewater concentration of 5-100 mg/L. Sensitivity analysis revealed that the voltage change (ΔV) was strongly correlated with the BPA concentration, with R² as high as 0.97. This study was the first to investigate the number of repeated uses of the MFC sensor, using sodium acetate as the regeneration solution for the MFC sensor, leading to a successful recovery of detection performance. However, as the number of uses increased (up to the third or fourth use), the ΔV of the MFC sensor for BPA gradually decreased and the sensitivity decreased significantly from 0.238 mV/mg/L to 0.027 mV/mg/L. In the low BPA concentration range (≦20 mg/L), the MFC sensor can be reused up to 5 times, demonstrating that the proposed MFC sensor can be reused. Microorganisms contribute to the power generation of the MFC sensor, which can be exploited in the detection of pollutants, enabling the determination of wastewater toxicity and providing early warnings of thereof. Conventional MFC sensors are complex and lack the ability to explore repeated use, so they are not easily applied to actual wastewater detection. The proposed MFC sensor has many advantages such as simplicity, rapid detection, and reusability, solving the problem of the high cost of using disposable MFC sensors and making them feasible for practical use.

A novel bimetallic MOFs combined with gold nanoflakes in electrochemical sensor for measuring bisphenol A

In this paper, a novel bimetallic Fe-Cu metal-organic framework combined with 1,3,5-benzenetricarboxylic acid (Fe-Cu-BTC) are synthesized using hydrothermal reaction. The bimetallic Fe-Cu-BTC with high BET (1504 cm³ g^-1) and high Langmuir surface area (1831 cm³ g^-1) is composited by gold nanoparticles to improve the conductivity and to develop their synergistic effect. A novel bisphenol A (BPA) sensor was prepared by dropcasting Fe-Cu-BTC on glassy carbon electrodes (GCE) followed by AuNPs electrodeposition. The Fe-Cu-BTC framework were characterized by X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy studies (TEM), FT-IR, BET measurements and EDX spectra. Cyclic voltammetry (CV) and differential pulse voltammetry (DPV) were carried out for surveying the electrochemical properties of the sensors and for the quantification of BPA. Two linear ranges of BPA concentrations 0.1-1.0 μM and 1.0-18 μM with 18 nM limit of detection were obtained. The developed sensor was used to measure the concentration of BPA in samples extracted from rain coat with the recovery ranging from 85.70 to 103.23%.

Emerging electrochemical techniques for identifying and removing micro/nanoplastics in urban waters

The ubiquitous micro/nanoplastics (MPs/NPs) in urban waters are priority pollutants due to their toxic effects on living organisms. Currently, great efforts have been made to realize a plastic-free urban water system, and the identification and removal of MPs/NPs are two primary issues. Among diverse methods, emerging electrochemical techniques have gained growing interests owing to their facile implementation, high efficiency, eco-compatibility, onsite operation, etc. Herein, recent progress in the electrochemical identification and removal of MPs/NPs in urban waters are comprehensively reviewed. The electrochemical sensing of MPs/NPs and their released pollutants (e.g., bisphenol A (BPA)) has been analyzed, and the sensing principles and the featured electrochemical devices/electrodes are examined. Afterwards, recent applications of electrochemical methods (i.e., electrocoagulation, electroadsorption, electrokinetic separation and electrochemical degradation) in MPs/NPs removal are discussed in detail. The influences of critical parameters (e.g., plastics' property, current density and electrolyte) in the electrochemical identification and removal of MPs/NPs are also analyzed. Finally, the current challenges and prospects in electrochemical sensing and removal of MPs/NPs in urban waters are elaborated. This review would advance efficient electrochemical technologies for future MPs/NPs pollutions management in urban waters.

Towards Development of Molecularly Imprinted Electrochemical Sensors for Food and Drug Safety: Progress and Trends

Due to their advantages of good flexibility, low cost, simple operations, and small equipment size, electrochemical sensors have been commonly employed in food safety. However, when they are applied to detect various food or drug samples, their stability and specificity can be greatly influenced by the complex matrix. By combining electrochemical sensors with molecular imprinting techniques (MIT), they will be endowed with new functions of specific recognition and separation, which make them powerful tools in analytical fields. MIT-based electrochemical sensors (MIECs) require preparing or modifying molecularly imprinted polymers (MIPs) on the electrode surface. In this review, we explored different MIECs regarding the design, working principle and functions. Additionally, the applications of MIECs in food and drug safety were discussed, as well as the challenges and prospects for developing new electrochemical methods. The strengths and weaknesses of MIECs including low stability and electrode fouling are discussed to indicate the research direction for future electrochemical sensors.

Direct and Sensitive Electrochemical Detection of Bisphenol A in Complex Environmental Samples Using a Simple and Convenient Nanochannel-Modified Electrode

Rapid, convenient, and sensitive detection of Bisphenol A (BPA) in complex environmental samples without the need for tedious pre-treatment is crucial for assessing potential health risks. Herein, we present an electrochemical sensing platform using a simple nanochannel-modified electrode, which enables the direct and sensitive detection of BPA in complex samples. A vertically ordered mesoporous silica-nanochannel film (VMSF) with high-density nanochannels is rapidly and stably grown on the surface of a electrochemically activated glassy carbon electrode (p-GCE) by using the electrochemically assisted self-assembly (EASA) method. The high antifouling capability of the VMSF/p-GCE sensor is proven by investigating the electrochemical behavior of BPA in the presence of model coexisting interfering molecules including amylum, protein, surfactant, and humic acid. The VMSF/p-GCE sensor can sensitively detect BPA ranged from 50 to 1.0 μM and 1.0–10.0 μM, with low detection limits (15 nM). Owing to the electrocatalytic performance and high potential resolution of p-GCE, the sensor exhibits high selectivity for BPA detection in the presence of common environmental pollutants, including bisphenol S (BPS), catechol (CC), hydroquinone (HQ), and 4-nitrophenol (4-NP). In combination with the good antifouling property of the VMSF, direct detection of BPA in environmental water samples and soil leaching solution (SLS) is also realized without separation pretreatment. The developed VMSF/p-GCE sensor demonstrated advantages of simple structure, high sensitivity, good antifouling performance, and great potential in direct electroanalysis of endocrine-disrupting compounds in complex samples.

Electrochemical sensors based on carbon nanostructures for the analysis of bisphenol A-A review

Overuse of Bisphenol A (BPA), a proven endocrine disruptor, has become a serious public health problem across the world. It has the potential to harm both the environment and human health, notably reproductive disorders, heart disease, and diabetes. Accordingly, much attention has been paid to the detection of BPA to promote food safety and environmental health. Carbon based nanostructures have proven themselves well in a variety of applications, such as energy storage, catalysis and sensors, due to their remarkable properties. Therefore, researchers have recently focused on fabricating electrochemical BPA sensors based on carbon nanostructures due to their unique advantages, such as real-time monitoring, simplicity, high selectivity, high sensitivity and easy operation. The purpose of the current review was to summarize the recent findings on carbon nanostructures for electrochemically sensing the BPA, as well as relevant future prospects and ongoing challenges.

Application of Molecularly Imprinted Polymers in the Analysis of Waters and Wastewaters

The increase of the global population and shortage of renewable water resources urges the development of possible remedies to improve the quality and reusability of waste and contaminated water supplies. Different water pollutants, such as heavy metals, dyes, pesticides, endocrine disrupting compounds (EDCs), and pharmaceuticals, are produced through continuous technical and industrial developments that are emerging with the increasing population. Molecularly imprinted polymers (MIPs) represent a class of synthetic receptors that can be produced from different types of polymerization reactions between a target template and functional monomer(s), having functional groups specifically interacting with the template; such interactions can be tailored according to the purpose of designing the polymer and based on the nature of the target compounds. The removal of the template using suitable knocking out agents renders a recognition cavity that can specifically rebind to the target template which is the main mechanism of the applicability of MIPs in electrochemical sensors and as solid phase extraction sorbents. MIPs have unique properties in terms of stability, selectivity, and resistance to acids and bases besides being of low cost and simple to prepare; thus, they are excellent materials to be used for water analysis. The current review represents the different applications of MIPs in the past five years for the detection of different classes of water and wastewater contaminants and possible approaches for future applications.