Rapid adsorption of dyes from aqueous solutions by modified lignin derived superparamagnetic composites

Preparation of economical and reusable novel multi-chemically modified lignin-based adsorbent for efficient adsorption of lead ions

In this work, through sequential demethylation, amination and esterification, a novel multi-chemically modified lignin-based adsorbent (NMCL) was developed to remove lead ions (Pb2+) from wastewater. These modifications significantly enhanced lignin's reactivity and introduced diverse active sites, thereby improving its adsorption performances. The adsorption studies revealed that NMCL's adsorption followed the Langmuir isotherm model and Pseudo-second-order kinetics, confirming a monolayer chemical adsorption process. Thermodynamic analysis indicated the whole process was spontaneous, entropy-driven and endothermic. NMCL demonstrated exceptional adsorption capacity (334.8 mg/g) and high selectivity and reusability, retaining 92 % efficiency after ten cycles. In addition, the related adsorption mechanism studies highlight the potential of NMCL for wastewater treatment via mechanisms involving electrostatic attraction and coordination with -NH2 and -CSS groups. This study offers a novel idea on the high value utilization of lignin and provides a new method for the removal of Pb2+ from wastewater.

Superparamagnetic composites of lignin regenerated from ionic liquid solutions for the efficient and selective removal of cationic dyes

Magnetic lignin nanoparticles (MLNs) were prepared by inducing their self-assembly through lignin regeneration in the [N-methyl-2-pyrrolidone][C1-C4 carboxylic acid] ionic liquids ([NMP]ILs), which are low-cost protic ionic liquid. [NMP]ILs are self-assembling solvent that can enhance the adsorption capacity of MLNs to a greater degree than tetrahydrofuran or H2O. Additionally, the anion types of [NMP]IL greatly influence the physiochemical properties of MLNs. The MLNs prepared through self-assembly with [NMP][formate] (MLN/[NMP][For]) exhibited a higher maximum adsorption capacity (134.53 mg/g) than the [NMP]ILs of C2-C4 carboxylate anions. MLN/[NMP][For] demonstrated stable adsorption within a pH range of 6-10 or at high salt concentrations (0.01-0.5 mol/L), retaining over 80 % of its regeneration efficiency after 5 cycles. In addition, MLN/[NMP][For] selectively removed cationic dyes in mixed binary anionic-cationic dye solutions. This work demonstrated the feasibility of preparing magnetic biosorbents with good selectivity and stability though regeneration and by adjusting the anions of ionic liquids.

Lignin: A valuable and promising bio-based absorbent for dye removal applications

The importance of environmental issues and the existence of humans have led to the recognition of environmental concerns as the main risk to modern life. Notably, one major concern for protecting and managing the environment and human health is the presence of dyes in wastewater. Therefore, before discharging wastewater into mainstream water, it is crucial to remove dyes. Among all lignocellulosic materials, lignin is a highly fragrant biopolymer. Its abundant availability, complex structure, and numerous functional moieties, including hydroxyl, carboxyl, and phenolic, are used in different chemicals and applications. Based on this, lignin is a very useful green material for adsorption, specifically in removing both heavy metals and organic pollutants from wastewater. This article describes the use of lignin-based adsorbents as a recent breakthrough in the removal of dye from aqueous solutions. On the other hand, the review intends to encourage readers to study both established and novel avenues in lignin-based dye removal materials.

Eco-friendly regeneration of lignin with acidic deep eutectic solvent for adsorption of pollutant dyes for water cleanup

In this study, a simple and eco-friendly method was used to treat alkaline lignin with an acidic deep eutectic solvent (DES) to obtain regenerated lignin for the efficient adsorption of pollutant dyes from aqueous environment. Based on the yield and adsorption capacity of the sorbent for these dyes, conditions such as the type and concentration of DES component, solid-to-liquid ratio, reaction time, and temperature were optimized. By characterizing and comparing alkali lignin with regenerated lignin, a series of reactions were demonstrated to occur during the DES treatment process. The performance and mechanism of methylene blue and rhodamine B adsorption on regenerated lignin were studied systematically, and the maximum adsorbed amounts were 348.29 and 551.05 mg/g at 323 K, respectively. This study provides a new strategy for the green preparation of functionalized lignin and its use in the water pollutant treatment.

High surface area activated carbon from a pineapple (ananas comosus) crown via microwave-ZnCl2 activation for crystal violet and methylene blue dye removal: adsorption optimization and mechanism

In this investigation, microwave irradiation assisted by ZnCl2 was used to transform pineapple crown (PN) waste into mesoporous activated carbon (PNAC). Complementary techniques were employed to examine the physicochemical characteristics of PNAC, including BET, FTIR, SEM-EDX, XRD, and pH at the point-of-zero-charge (pHpzc). PNAC is mesoporous adsorbent with a surface area of 1070 m2/g. The statistical optimization for the adsorption process of two model cationic dyes (methylene blue: MB and, crystal violet: CV) was conducted using the response surface methodology-Box-Behnken design (RSM-BBD). The parameters include solution pH (4-10), contact time (2-12) min, and PNAC dosage (0.02-0.1 g/100 mL). The Freundlich and Langmuir models adequately described the dye adsorption isotherm results for the MB and CV systems, whereas the pseudo-second order kinetic model accounted for the time dependent adsorption results. The maximum adsorption capacity (qmax) for PNAC with the two tested dyes are listed: 263.9 mg/g for CV and 274.8 mg/g for MB. The unique adsorption mechanism of MB and CV dyes by PNAC implicates multiple contributions to the adsorption process such as pore filling, electrostatic forces, H-bonding, and π-π interactions. This study illustrates the possibility of transforming PN into activated carbon (PNAC) with the potential to remove two cationic dyes from aqueous media.

The mechanism of self-assembly of lignin in deep eutectic solvent based on sulfamic acid and urea through molecular dynamics simulation

Due to the diversity of industrial lignin sources and the complexity of its structure, its application as a high-value material is limited. Lignin nanoparticles (LNPs) have emerged as a hotspot for research due to their advantages of high specific surface area and high dispersion and the solvent transfer method is commonly used for the preparation of LNPs. In this paper, LNPs were prepared by solvent transfer method using DES based on sulfamic acid and urea (S/U DES) as solvent and water as anti-solvent. To explore the internal mechanism of the self-assembly of nanoparticles, a theoretical model of the solvent system and model lignin compound was constructed with the assistance of quantum chemistry and molecular dynamics theories. Through classical molecular dynamics (MD) simulations, the interaction energy, radius of gyration (ROG), solvent accessible surface area (SASS), radial and spatial distribution function (RDFs/SDFs), hydrogen bonding, and the morphology changes were analyzed to reveal the internal mechanism of self-assembly of model lignin compounds in S/U DES. This study is useful in revealing the mechanism of interaction between lignin and DES, as well as providing a benchmark for the green and efficient preparation of lignin nanoparticles.

Highly Sustainable Dyes Adsorption in Wastewater Using Textile Filters Fabricated by UV Irradiation

Vast amounts of dyeing wastewater released from the textile industry can not only cause water pollution but also have negative effects on the human body, such as skin irritation and respiratory diseases. Dye adsorption technology is necessary for the treatment of wastewater discharged from the dyeing industry and for environmental improvement. However, to remove dyeing wastewater, more energy and solvents are used to fabricate adsorbents, or excessive energy is used to filter dyeing wastewater out, resulting in more environmental pollution. Therefore, it is necessary to develop a method of filtering dyeing wastewater in a more environmentally friendly manner by minimizing the use of solvents and energy. In this study, we modified the surface of a textile substrate through UV irradiation to create a monomer capable of facilely bonding with dyes. Employing the UV photografting method, we were able to produce a dye adsorption filter in a more environmentally friendly manner, minimizing solvent usage and heat energy consumption required for absorbent synthesis. At a monomer concentration of 10%, the fabricated filter exhibited a dye removal efficiency of 97.34% after 24 h, all without the need for a pressure treatment or temperature increase. Moreover, it displayed an adsorption capacity of approximately 77.88 mg per 1 g of filter material.

Cellulose-supported bioadsorbent from natural hemp fiber for removal of anionic dyes from aqueous solution

The aim of this study is to prepare an eco-friendly bioadsorbent by graft copolymerization and modification from hemp fiber including bio-macromolecules such as cellulose, hemicellulose and lignin for anionic dyes adsorption from aqueous solutions, and to investigate adsorptive properties. The prepared cellulose-supported bioadsorbent (TEPA-(GMA-g-HF)) was characterized in detail using SEM-EDX, STEM, FTIR, XRD, TGA and BET techniques and calculating the point of zero charge. It was used as an adsorbent to remove three different anionic dyes, Remazol Brilliant Blue R (RBBR), Reactive Red 120 (RR120) and Reactive yellow 160 (RY160) from the aqueous medium. The effects of adsorbent amount, pH, initial dye concentration, time and temperature on the adsorption were investigated. From the results, it was determined that the adsorption of all three dyes to the developed fibrous bioadsorbent was more compatible with the pseudo-second-order kinetic and the Langmuir isotherm model. It was found that the adsorption capacity increased with increasing temperature, and the adsorption capacity at 298 K was 91.70 mg/g for RBBR, 83.33 for RY160 and 76.34 mg/g for RR120, respectively. Dye removal efficiencies were provided as approximately 100 % at acidic pHs. This high removal efficiency has also achieved in the dense matrix medium, and even after five consecutive reused.

A combined experimental and modeling approach to elucidate the adsorption mechanism for sustainable water treatment via In2S3-anchored chitosan

A novel Chitosan/Indium sulfide (CS/In2S3) nanocomposite was created by co-precipitating Chitosan and InCl3 in solution, resulting in In2S3 agglomeration on the Chitosan matrix with a remarkable pore diameter of 170.384 Å, and characterized it for the physical and chemical properties. Under optimal conditions (pH = 7, time = 60 min, catalyst dosage = 0.24 g L-1, and dye concentration = 100 mg L-1), the synthesized nanocomposite demonstrated remarkable adsorption capabilities for Victoria Blue (VB), attaining a removal efficiency of 90.81%. The Sips adsorption isotherm best matched the adsorption process, which followed pseudo-second-order kinetics. With a rate constant of 6.357 × 10-3 g mg-1 min-1, the highest adsorption capacity (qm) was found to be 683.34 mg g-1. Statistical physics modeling (SPM) of the adsorption process revealed multi-interaction and multi-molecular adsorption of VB on the CS/In2S3 surface. The nanocomposite demonstrated improved stability and recyclability, indicating the possibility for low-cost, reusable wastewater dye removal adsorbents. These results have the potential to have practical applications in environmental remediation.

Biosorption of a common micropollutant (methylene blue) from a water environment by chemically activated biomass of a widely available plant species (Pyracantha coccinea M. J. Roemer)

Recently, to protect the health of aquatic life and, indirectly, all living things, biomass-based substances have been increasingly applied as biosorbent materials to remove micropollutant agents from an aquatic environment. However, these studies are under development, and the search for more successful materials continues. Here, the biosorption of a common micropollutant, methylene blue, from an aquatic environment was investigated using the chemically activated biomass of a widely available plant species, Pyracantha coccinea M. J. Roemer. The biosorption efficiency of the biosorbent material was improved by optimizing the experimental conditions, including the contact time, micropollutant load, pH, and biosorbent material amount, and the highest performance was observed at t = 360 mins, C0 = 15 mg L-1, pH = 8 and m = 10 mg. The pseudo-second-order kinetics model and Freundlich isotherm model were in good agreement with the experimentally obtained results. The thermodynamic study suggested that the micropollutant biosorption was a favorable, spontaneous, and physical process. The micropollutant-biosorbent interaction mechanism was presented using SEM and FTIR studies. The maximum Langmuir biosorption capacity of the biosorbent was determined to be 156.674 mg g-1. The activation operation more than doubled the biosorption potential of the biosorbent material. Thus, the present study showed that the chemically activated plant biomass-based material could be a promising biosorbent for the effective removal of the micropollutant from water environment.

A functional lignin for heavy metal ions adsorption and wound care dressing

Recently, the application of lignin activation by demethylation to improve reactivity and enrich multiple functions has intensively attracted attention. However, it is still challenge up to now due to the low reactivity and complexity of lignin structure. Here, an effective demethylation way was explored by microwave-assisted method for substantially enhancing the hydroxyl (-OH) content and retaining the structure of lignin. Then, the optimum demethylated lignin was used to removal heavy metal ions and promote wound healing, respectively. In detail, for microwave-assisted demethylated poplar lignin (M-DPOL), the contents of phenolic (Ar-OH) and total hydroxyl (Tot-OH) groups reached the maximum for 60 min at 90 °C in DMF with 7.38 and 9.13 mmol/g, respectively. After demethylation, with this M-DPOL as lignin-based adsorbent, the maximum adsorption capacity (Qmax) for Pb2+ ions reached 104.16 mg/g. Based on the isotherm, kinetic and thermodynamic models analyses, the chemisorption occurred in monolayer on the surface of M-DPOL, and all adsorption processes were endothermic and spontaneous. Meanwhile, M-DPOL as a wound dressing had excellent antioxidant property, outstanding bactericidal activity and remarkable biocompatibility, suggesting that it did not interfere with cell proliferation. Besides, the wounded rats treated with M-DPOL significantly promoted its formation of re-epithelialization and wound healing of full-thickness skin defects. Overall, microwave-assisted method of demethylated lignin can offer great advantages for heavy metal ions removal and wound care dressing, which facilitates high value application of lignin.

Designed synthesis of multifunctional lignin-based adsorbent for efficient heavy metal ions removal and electromagnetic wave absorption

Multifunctional lignin-based adsorbents, which have shown great application prospect, have attracted widespread attention. Herein, a series of multifunctional lignin-based magnetic recyclable adsorbents were prepared from carboxymethylated lignin (CL), which was rich in carboxyl group (-COOH). After optimizing the mass ratio of CL to Fe₃O₄, the prepared CL/Fe₃O₄ (3:1) adsorbent showed efficient adsorption capacities for heavy metal ions. The kinetic and isotherm nonlinear fitting studies revealed that the adsorption process followed the second-order kinetic and Langmuir models, and the maximum adsorption capacities (Q_max) of CL/Fe₃O₄ (3:1) magnetic recyclable adsorbent for Pb²⁺, Cu²⁺ and Ni²⁺ ions reached 189.85, 124.43 and 106.97 mg/g, respectively. Meanwhile, after 6 cycles, the adsorption capacities of CL/Fe₃O₄ (3:1) for Pb²⁺, Cu²⁺ and Ni²⁺ ions could keep at 87.4 %, 83.4 % and 82.3 %, respectively. In addition, CL/Fe₃O₄ (3:1) also exhibited excellent electromagnetic wave absorption (EMWA) performance with a reflection loss (RL) of -28.65 dB at 6.96 GHz under the thickness of 4.5 mm, and its effective absorption bandwidth (EAB) achieved 2.24 GHz (6.08-8.32 GHz). In short, the prepared multifunctional CL/Fe₃O₄ (3:1) magnetic recyclable adsorbent with outstanding adsorption capacity for heavy metal ions and superior EMWA capability opens a new avenue for the diversified utilization of lignin and lignin-based adsorbent.

Influence of structure and functional group of modified kraft lignin on adsorption behavior of dye

Utilization of kraft lignin to produce bio-based adsorptive material for effective dye adsorption from industrial wastewater is essential to fulfilling the significant environmental protection needs. Lignin is the most abundant byproduct material with a chemical structure containing various functional groups. However, the complicated chemical structure makes it somewhat hydrophobic and incompatible, which limits its direct application as an adsorption material. Chemical modification is a common way to enhance lignin properties. In this work, the kraft lignin was modified through direct amination using Mannich reaction and oxidization followed by amination as new route of lignin modification. The prepared lignins, including aminated lignin (AL), oxidized lignin (OL), and aminated-oxidized lignin (AOL), as well as unmodified kraft lignin, were analyzed by Fourier transform infrared spectroscopy (FT-IR), thermogravimetric analysis (TGA), scanning electron microscope (SEM), X-ray photoelectron spectroscopy (XPS), elemental analysis and ¹H-nuclear magnetic resonance measurements (¹HNMR). The adsorption behaviors of modified lignins for the malachite green in aqueous solution were investigated well and discussed, as well as the adsorption kinetics and thermodynamic equations. Compared with other aminated lignin (AL), the AOL displayed a high adsorption capacity of 99.1 % dye removal, due to its more effective functional groups. The change in structure and functional groups on the lignin molecules during oxidation and amination had no effect on its adsorption mechanisms. The adsorption process of malachite green on different kinds of lignin belongs to endothermic chemical adsorption, which mainly consists of monolayer adsorption. The modification of lignin through oxidation followed by amination process, afforded kraft lignin a broad potential application in the field of wastewater treatment.

Preparation of Amphiphilic Chitosan-Loaded Bentonite Adsorbent and Its Performance in Removing Organic Matter from Coking Wastewater

An amphiphilic chitosan-loaded bentonite adsorbent (C18CTS-BT) was prepared for the efficient removal of organic matter from coking wastewater. The structure and surface morphology of adsorbents were characterized by FT-IR, XRD, and SEM. The removal of those organics by C18CTS-BT was investigated by comparing the adsorption performances of C18CTS-BT with bentonite (BT) and chitosan-loaded bentonite (CTS-BT). The results showed that compared with BT and CTS-BT, C18CTS-BT showed the performance advantages of having a low dosage, wide pH range, and short adsorption equilibrium time. The optimized treatment process was as follows: the adsorbent dosage was 1.5 g·L^-1, the adsorption time was 60 min, and the pH of the system was 7.0. The chemical oxygen demand (COD) of the coking wastewater treated with BT, CTS-BT, and C18CTS-BT decreased from 342 mg·L^-1 in the raw water to 264 mg·L^-1, 218 mg·L^-1, and 146 mg·L^-1, corresponding to COD removal rates of 22.81%, 36.26%, and 57.31%, respectively. The results of GC-MS analysis also confirmed that C18CTS-BT could remove most of the organic compounds in coking wastewater, especially long-chain alkanes and their derivatives. The hydrophobic modification of the adsorbent material can effectively improve the removal performance of organic compounds from coking wastewater.

Effects of direct sulfonation on the catalytic activity and recyclability of novel lignin-based solid acid catalysts from agri-food waste

Catalytic systems derived from lignin are emerging as quite efficient and profitable materials in many catalyzed transformations. However, these catalysts have been predominantly synthesized by carbonization. Alternatively, we prepared direct sulfonation lignin (DSL) and compared it to the carbonized-sulfonated lignin (CSL) catalyst, aiming to reveal the effects of direct functionalization of lignin on its catalytic performance and to simplify its preparation. Both catalysts were well characterized by several physicochemical techniques, and their catalytic activities were assessed by catalyzed esterification. Using CSL, the yield reached 94.11 % under the optimal conditions (60 °C, 4 h and 50 mg loading), while DSL yielded 93.97 % with only 2 h under the same conditions, which is attributed to the abundant catalytic active sites in DSL (0.62 mmol/g of SO₃H against 0.39 mmol/g for CSL). Furthermore, the activation energies were found to be 21 and 16 kJ mol^-1 for CSL and DSL, respectively, suggesting that esterification can occur with less energy input using DSL. Reusability showed that leaching of SO₃H groups and mass loss are inherently responsible for deactivation. However, both lignin-based catalysts show good stability and can be reused for 4 successive cycles. Direct lignin functionalization can be an alternative to conventional catalyst processing.

A new type of calcium-rich biochars derived from spent mushroom substrates and their efficient adsorption properties for cationic dyes

Adsorption is commonly accepted as a most promising strategy in dye wastewater treatment, and the widespread use of adsorption emphasizes the need to explore low-cost but excellent adsorbents. Herein, a low-cost adsorbent (calcium-rich biochar) was developed, which was directly pyrolyzed from spent mushroom substate without any modification. This study evaluated the potential application of two calcium-rich biochars (GSBC and LSBC) derived from spent substrates of Ganoderma lucidum and Lentinus edodes, respectively. The effects of pyrolysis temperature on the calcium-rich biochars characteristics and their adsorption mechanism for cationic dyes (Malachite Green oxalate (MG) and Safranine T (ST)) were studied systematically. The increase in pyrolysis temperature from 350 to 750 °C led to an increase in both biochar ash, Ca content, and specific surface area, which made high-temperature biochars (GS750 and LS750) the superior adsorbents for cationic dyes. Batch adsorption results showed LS750 was more efficient to adsorb dyes than GS750 attributed to its higher Ca content and larger specific surface area. According to the Langmuir model, LS750 had high adsorption capacities of 9,388.04 and 3,871.48 mg g⁻¹ for Malachite green and ST, respectively. The adsorption mechanism of dye MG could be attributed to pore filling, hydrogen bonding, electrostatic interaction, ion exchange, and π-π stacking, while ST adsorption mainly involved pore filling, electrostatic interaction, ion exchange, and π-π stacking. Attributed to their excellent adsorption performance, cheap source, and good reusability, biochars obtained from SMSs were very promising in dyeing wastewater treatment.