Accessible Eco-Friendly Method for Wastewater Removal of the Azo Dye Reactive Black 5 by Reusable Protonated Chitosan-Deep Eutectic Solvent Beads

A novel approach to enhance the utilization of low-cost and sustainable chitosan for wastewater remediation is presented in this investigation. The study centers around the modification of chitosan beads using a deep eutectic solvent composed of choline chloride and urea at a molar ratio of 1:2, followed by treatment with sulfuric acid using an impregnation accessible methodology. The effectiveness of the modified chitosan beads as an adsorbent was evaluated by studying the removal of the azo dye Reactive Black 5 (RB5) from aqueous solutions. Remarkably, the modified chitosan beads demonstrated a substantial increase in adsorption efficiency, achieving excellent removal of RB5 within the concentration range of 25-250 mg/L, ultimately leading to complete elimination. Several key parameters influencing the adsorption process were investigated, including initial RB5 concentration, adsorbent dosage, contact time, temperature, and pH. Quantitative analysis revealed that the pseudo-second-order kinetic model provided the best fit for the experimental data at lower dye concentrations, while the intraparticle diffusion model showed superior performance at higher RB5 concentration ranges (150-250 mg/L). The experimental data were successfully explained by the Langmuir isotherm model, and the maximum adsorption capacities were found to be 116.78 mg/g at 298 K and 379.90 mg/g at 318 K. Desorption studies demonstrated that approximately 41.7% of the dye could be successfully desorbed in a single cycle. Moreover, the regenerated adsorbent exhibited highly efficient RB5 removal (80.0-87.6%) for at least five consecutive uses. The outstanding adsorption properties of the modified chitosan beads can be attributed to the increased porosity, surface area, and swelling behavior resulting from the acidic treatment in combination with the DES modification. These findings establish the modified chitosan beads as a stable, versatile, and reusable eco-friendly adsorbent with high potential for industrial implementation.

Natural Polysaccharide-Based Hydrogels Used for Dye Removal

Removal of contaminants from discharge water is vital and demands urgent assistance with the goal to keep clean water. Adsorption is one of the most common, efficient, and low-priced methods used in water treatment. Various polysaccharide-based gels have been used as efficient dye adsorbents from wastewater. This review summarizes cutting-edge research of the last decade of different hydrogels based on natural polysaccharides (chitin, chitosan, cellulose, starch, pullulan, and dextran) concerning their dye adsorption efficiency. Beyond their natural abundance, attributes of polysaccharides such as biocompatibility, biodegradability, and low cost make them not only efficient, but also environmentally sustainable candidates for water purification. The synthesis and dye removal performance together with the effect of diverse factors on gels retaining ability, kinetic, and isotherm models encountered in adsorption studies, are introduced. Thermodynamic parameters, sorbent recycling capacity along with conclusions and future prospects are also presented.

Rapid, Massive, and Green Synthesis of Polyoxometalate-Based Metal-Organic Frameworks to Fabricate POMOF/PAN Nanofiber Membranes for Selective Filtration of Cationic Dyes

Developing high-efficiency membrane materials for the rapid removal of organic dyes is crucial but remains a challenge. Polyoxometalates (POMs) clusters with anionic structures are promising candidates for the removal of cationic dyes via electrostatic interactions. However, their shortcomings, such as their solubility and inability to be mass-produced, hinder their application in water pollution treatment. Here, we propose a simple and green strategy utilizing the room temperature stirring method to mass produce nanoscale polyoxometalate-based metal-organic frameworks (POMOFs) with porous rhomboid-shaped dodecahedral and hexagonal prism structures. The products were labeled as POMOF1 (POMOF-PW12) and POMOF2 (POMOF-PMo12). Subsequently, a series of x wt% POMOF1/PAN (x = 0, 3, 5, and 10) nanofiber membranes (NFMs) were prepared using electrospinning technology, where polyacrylonitrile (PAN) acts as a "glue" molecule facilitating the bonding of POMOF1 nanoparticles. The as-prepared samples were comprehensively characterized and exhibited obvious water stability, as well as rapid selective adsorption filtration performance towards cationic dyes. The 5 wt% POMOF1/PAN NFM possessed the highest removal efficiency of 96.7% for RhB, 95.8% for MB, and 86.4% for CV dyes, which realized the selective separation over 95% of positively charged dyes from the mixed solution. The adsorption mechanism was explained using FT-IR, SEM, Zeta potential, and adsorption kinetics model, which proved that separation was determined via electrostatic interaction, hydrogen bonding, and π-π interactions. Moreover, the POMOF1/PAN membrane presented an outstanding recoverable and stable removal rate after four cycles. This study provides a new direction for the systematic design and manufacture of membrane separation materials with outstanding properties for contaminant removal.

Bimetallic Organic Gel for Effective Methyl Orange Dye Adsorption

A bimetallic organic gel (MOG-Fe/Al) was synthesized through the solvothermal method. The gel state of the product obtained under optimized gel formation conditions is sufficient to carry 2 g of weight for a long time. Scanning electron microscopy (SEM), X-ray diffraction (XRD), Fourier transform infrared (FT-IR) spectroscopy, Brunauer-Emmett-Teller (BET) technique, and X-ray photoelectron spectroscopy (XPS) analysis confirmed the structures and morphologies of the synthesized materials. MOG-Fe/Al, with good stability, excellent durability, and wide applicability, exhibited efficient MO adsorption capacity as high as 335.88 mg/g at 25 °C. Adsorption-influencing factors including solution pH, contact time, and temperature were investigated. The adsorption performance of the bimetallic organic gel was better than that of the monometallic organic gels (MOG-Fe and MOG-Al), and its adsorption processes were in accordance with the pseudo-second-order kinetic and Langmuir isothermal models. The excellent adsorption capacity of the MOG-Fe/Al is due to its surface structure, pore volume, π-π interactions, hydrogen bonds, and electrostatic interactions.

An Updated Overview of Magnetic Composites for Water Decontamination

Water contamination by harmful organic and inorganic compounds seriously burdens human health and aquatic life. A series of conventional water purification methods can be employed, yet they come with certain disadvantages, including resulting sludge or solid waste, incomplete treatment process, and high costs. To overcome these limitations, attention has been drawn to nanotechnology for fabricating better-performing adsorbents for contaminant removal. In particular, magnetic nanostructures hold promise for water decontamination applications, benefiting from easy removal from aqueous solutions. In this respect, numerous researchers worldwide have reported incorporating magnetic particles into many composite materials. Therefore, this review aims to present the newest advancements in the field of magnetic composites for water decontamination, describing the appealing properties of a series of base materials and including the results of the most recent studies. In more detail, carbon-, polymer-, hydrogel-, aerogel-, silica-, clay-, biochar-, metal-organic framework-, and covalent organic framework-based magnetic composites are overviewed, which have displayed promising adsorption capacity for industrial pollutants.

Hierarchical Porous Activated Carbon from Wheat Bran Agro-Waste: Applications in Carbon Dioxide Capture, Dye Removal, Oxygen and Hydrogen Evolution Reactions

This work reports an efficient method for facile synthesis of hierarchically porous carbon (WB-AC) utilizing wheat bran waste. Obtained carbon showed 2.47 mmol g-1 CO2 capture capacity with good CO2 /N2 selectivity and 27.35 to 29.90 kJ mol-1 isosteric heat of adsorption. Rapid removal of MO dye was observed with a capacity of ~555 mg g-1 . Moreover, WB-AC demonstrated a good OER activity with 0.35 V low overpotential at 5 mA cm-2 and a Tafel slope of 115 mV dec-1 . It also exhibited high electrocatalytic HER activity with 57 mV overpotential at 10 mA cm-2 and a Tafel slope of 82.6 mV dec-1 . The large SSA (757 m2  g-1 ) and total pore volume (0.3696 cm3  g-1 ) result from N2 activation contributing to selective CO2 uptake, high and rapid dye removal capacity and superior electrochemical activity (OER/HER), suggesting the use of WB-AC as cost effective adsorbent and metal free electrocatalyst.

Hybrid magnetic CoFe2O4@γ-Fe2O3@CTAB nanocomposites as efficient and reusable adsorbents for Remazol Brilliant Blue R dye

The main goal of the present survey was to elaborate, characterize and evaluate the efficiency of ferrite-based nanoparticles modified with cetyltrimethylammonium bromide (CTAB) as potential magnetic nanoadsorbents to remove Remazol Brilliant Blue R (RBBR) from water. It is proposed an innovative nanomaterial architecture based on highly magnetic and chemically stable core@shell nanoparticles covered by an adsorptive surface layer of CTAB (CoFe2O4@γ-Fe2O3@CTAB). Samples of two different mean sizes (7.5 and 14.6 nm) were synthesized using a hydrothermal coprecipitation followed by surface treatment and functionalization. Batch tests were performed to evaluate the influence of contact time, temperature, pH, shaking rate, presence of interferents and mean size on the performance of the proposed nanomaterials. The kinetics of the adsorption process followed the pseudo-second-order model with an equilibrium time of 20 min. The adsorption capacity was estimated by the Langmuir isotherm model and was found to be 56.3 mg/g (smaller size) and 45.6 mg/g (larger size) at pH = 3 and a shaking rate of 400 rpm. The process was spontaneous, exothermic, and showed increased randomness. Sulphate ions negatively impacted the removal of RBBR. The best performance of the nanoadsorbent based on smaller mean sizes can be correlated to its larger surface area. Regeneration and readsorption tests showed that the nanoadsorbents retain more than 80% of their original removal capacity, therefore they can be effectively recycled and reused.

From Water for Water: PEDOT:PSS-Chitosan Beads for Sustainable Dyes Adsorption

This study investigates the viability of developing chitosan-based hydrogels derived from waste shrimp shells for the removal of methylene blue and methyl orange, thereby transforming food waste into advanced materials for environmental remediation. Despite chitosan-based adsorbents being conventionally considered ideal for the removal of negative pollutants, through targeted functionalization with poly(3,4-ethylenedioxythiophene): polystyrene sulfonate (PEDOT:PSS) at varying concentrations, we successfully enhance the hydrogels' efficacy in also adsorbing positively charged adsorbates. Specifically, the incorporation of PEDOT:PSS at a concentration of 10% v/v emerges as a critical factor in facilitating the robust adsorption of dyes. In the case of the anionic dye methyl orange (MO, 10-5 M), the percentage of removed dye passed from 47% (for beads made of only chitosan) to 66% (for beads made of chitosan-PEDOT:PSS 10%), while, in the case of the cationic dye methylene blue (MB, 10-5 M), the percentage of removed dye passed from 52 to 100%. At the basis of this enhancement, there is an adsorption mechanism resulting from the interplay between electrostatic forces and π-π interactions. Furthermore, the synthesized functionalized hydrogels exhibit remarkable stability and reusability (at least five consecutive cycles) in the case of MB, paving the way for the development of cost-effective and sustainable adsorbents. This study highlights the potential of repurposing waste materials for environmental benefits, introducing an innovative approach to address the challenges regarding water pollution.

The Effect of Silver Nanoparticles/Titanium Dioxide in Poly(acrylic acid-co-acrylamide)-Modified, Deproteinized, Natural Rubber Composites on Dye Removal

This work aims to enhance the dye-removal performance of prepared poly(acrylic acid-co-acrylamide)-modified, deproteinized, natural rubber ((PAA-co-PAM)-DPNR) through incorporation with silver nanoparticles/titanium dioxide. The (PAA-co-PAM)-DPNR was prepared by emulsion-graft copolymerization with a grafting efficiency of 10.20 ± 2.33 to 54.26 ± 1.55%. The composites based on (PAA-co-PAM)-DPNR comprising silver nanoparticles and titanium dioxide ((PAA-co-PAM)-DPNR/Ag-TiO2) were then prepared by latex compounding using the fixed concentration of AgNO3 (0.5 phr) and varying concentrations of TiO2 at 1.0, 2.5, and 5.0 phr. The formation of silver nanoparticles was obtained by heat and applied pressure. The composites had a porous morphology as they allowed water to diffuse in their structure, allowing the high specific area to interact with dye molecules. The incorporation of silver nanoparticles/titanium dioxide improved the compressive modulus from 1.015 ± 0.062 to 2.283 ± 0.043 KPa. The (PAA-co-PAM)-DPNR/Ag-TiO2 composite with 5.0 phr of TiO2 had a maximum adsorption capacity of 206.42 mg/g, which increased by 2.02-fold compared to (PAA-co-PAM)-DPNR. The behavior of dye removal was assessed with the pseudo-second-order kinetic model and Langmuir isotherm adsorption model. These composites can maintain their removal efficiency above 90% for up to five cycles. Thus, these composites could have the potential for dye-removal applications.

Highly Sustainable Dyes Adsorption in Wastewater Using Textile Filters Fabricated by UV Irradiation

Vast amounts of dyeing wastewater released from the textile industry can not only cause water pollution but also have negative effects on the human body, such as skin irritation and respiratory diseases. Dye adsorption technology is necessary for the treatment of wastewater discharged from the dyeing industry and for environmental improvement. However, to remove dyeing wastewater, more energy and solvents are used to fabricate adsorbents, or excessive energy is used to filter dyeing wastewater out, resulting in more environmental pollution. Therefore, it is necessary to develop a method of filtering dyeing wastewater in a more environmentally friendly manner by minimizing the use of solvents and energy. In this study, we modified the surface of a textile substrate through UV irradiation to create a monomer capable of facilely bonding with dyes. Employing the UV photografting method, we were able to produce a dye adsorption filter in a more environmentally friendly manner, minimizing solvent usage and heat energy consumption required for absorbent synthesis. At a monomer concentration of 10%, the fabricated filter exhibited a dye removal efficiency of 97.34% after 24 h, all without the need for a pressure treatment or temperature increase. Moreover, it displayed an adsorption capacity of approximately 77.88 mg per 1 g of filter material.

Production of biochar from Melia azedarach seeds for the crystal violet dye removal from water: combining of hydrothermal carbonization and pyrolysis

Biochar has shown large potential in water treatment because of its low cost, good textural properties, and high reusability. In this study, two porous biochars were developed from the Melia azedarach seeds via direct pyrolysis process (B-700) and through hydrothermal carbonization followed with pyrolysis (HB-700). They were characterized by morphology, structural characteristics, and surface features and used to adsorb the crystal violet (CV) dye in water environment. Results of the isotherm approaches demonstrated that the removal capacity of these biochars reached 119.4 mg/g for B-700, and 209 mg/g for HB-700 (at 45°C). Also, the Avrami model best fitted the kinetic data. The electrostatic attraction was regarded as one of the adsorptions mechanisms of CV dye. The regeneration tests reveal that both B-700 and HB-700 are good reusable adsorbents. Finally, findings of the study showed that the hydrothermal carbonization method that precede the pyrolysis process can improve significantly the adsorption capacity of the produced biochar.

Decolorization of Textile Azo Dye via Solid-State Fermented Wheat Bran by Lasiodiplodia sp. YZH1

Textile dyes are one of the major water pollutants released into water in various ways, posing serious hazards for both aquatic organisms and human beings. Bioremediation is a significantly promising technique for dye decolorization. In the present study, the fungal strain Lasiodiplodia sp. was isolated from the fruiting bodies of Schizophyllum for the first time. The isolated fungal strain was examined for laccase enzyme production under solid-state fermentation conditions with wheat bran (WB) using ABTS and 2,6-Dimethoxyphenol (DMP) as substrates, then the fermented wheat bran (FWB) was evaluated as a biosorbent for Congo red dye adsorption from aqueous solutions in comparison with unfermented wheat bran. A Box-Behnken design was used to optimize the dye removal by FWB and to analyze the interaction effects between three factors: fermentation duration, pH, and dye concentration. Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), and scanning electron microscopy (SEM) were applied to study the changes in the physical and chemical characteristics of wheat bran before and after fermentation. An additional experiment was conducted to investigate the ability of the Lasiodiplodia sp. YZH1 to remove Congo red in the dye-containing liquid culture. The results showed that laccase was produced throughout the cultivation, reaching peak activities of ∼6.2 and 22.3 U/mL for ABTS and DMP, respectively, on the fourth day of cultivation. FWB removed 89.8% of the dye (100 mg L-1) from the aqueous solution after 12 h of contact, whereas WB removed only 77.5%. Based on the Box-Behnken design results, FWB achieved 93.08% dye removal percentage under the conditions of 6 days of fermentation, pH 8.5, and 150 mg L-1 of the dye concentration after 24 h. The fungal strain removed 95.3% of 150 mg L-1 of the dye concentration after 8 days of inoculation in the dye-containing liquid culture. These findings indicate that this strain is a worthy candidate for dye removal from environmental effluents.

Preparation and Characterization of New and Low-Cost Ceramic Flat Membranes Based on Zeolite-Clay for the Removal of Indigo Blue Dye Molecules

Composite flat membranes were prepared using a dry uniaxial pressing process. The effect of the sintering temperature (850-950 °C) and smectite proportion (10-50 wt.%) on membrane properties, such as microstructure, mechanical strength, water permeability, and treatment performances, was explored. It was observed that increasing the sintering temperature and adding higher amounts of smectite increased the mechanical strength and shrinkage. Therefore, 850 °C was chosen as the optimum sintering temperature because the composite membranes had a very low shrinkage that did not exceed 5% with high mechanical strength, above 23 MPa. The study of smectite addition (10-50 wt.%) showed that the pore size and water permeability were significantly reduced from 0.98 to 0.75 µm and from 623 to 371 L·h-1·m-2·bar-1, respectively. Furthermore, the application of the used membranes in the treatment of indigo blue (IB) solutions exhibited an almost total turbidity removal. While the removal of color and COD decreased from 95% to 76%, respectively, they decreased from 95% to 52% when the amount of smectite increased. To verify the treated water's low toxicity, a germination test was performed. It has been shown that the total germination of linseed grains irrigated by MS10-Z90 membrane permeate was identical to that irrigated with distilled water. Finally, based on its promising properties, its excellent separation efficiency, and its low energy consumption, the MS10-Z90 (10 wt.% smectite and 90 wt.% zeolite) sintered at 850 °C could be recommended for the treatment of colored industrial wastewater.

Microbial synthesis of titanium dioxide nanoparticles and their importance in wastewater treatment and antimicrobial activities: a review

Nanotechnology (NT) and nanoparticles (NPs) have left a huge impact on every field of science today, but they have shown tremendous importance in the fields of cosmetics and environmental cleanup. NPs with photocatalytic effects have shown positive responses in wastewater treatment, cosmetics, and the biomedical field. The chemically synthesized TiO2 nanoparticles (TiO2 NPs) utilize hazardous chemicals to obtain the desired-shaped TiO2. So, microbial-based synthesis of TiO2 NPs has gained popularity due to its eco-friendly nature, biocompatibility, etc. Being NPs, TiO2 NPs have a high surface area-to-volume ratio in addition to their photocatalytic degradation nature. In the present review, the authors have emphasized the microbial (algae, bacterial, fungi, and virus-mediated) synthesis of TiO2 NPs. Furthermore, authors have exhibited the importance of TiO2 NPs in the food sector, automobile, aerospace, medical, and environmental cleanup.

Adsorption of methyl orange on low-cost adsorbent natural materials and modified natural materials: a review

Recently a large number of extensive studies have amassed that describe the removal of dyes from water and wastewater using natural adsorbents and modified materials. Methyl orange dye is found in wastewater streams from various industries that include textiles, plastics, printing and paper among other sources. This article reviews methyl orange adsorption onto natural and modified materials. Despite many techniques available, adsorption stands out for efficient water and wastewater treatment for its ease of operation, flexibility and large-scale removal of colorants. It also has a significant potential for regeneration recovery and recycling of adsorbents in comparison to other water treatment methods. The adsorbents described herein were classified into five categories based on their chemical composition: bio-sorbents, activated carbon, biochar, clays and minerals, and composites. In this review article, we want to demonstrate the capacity of natural and modified materials for dye adsorption which can yield significant improvements to the adsorption capacity of dyes such as methyl orange. In addition, the effect of critical variables including contact time, initial methyl orange concentration, dosage of adsorbent, pH, temperature and mechanism on the adsorption efficiency will be covered as part of this literature review.

Fabrication of ZnO/ZnAl2O4/Au Nanoarrays through DC Electrodeposition Utilizing Nanoporous Anodic Alumina Membranes for Environmental Application

In this study, anodic aluminum oxide membranes (AAOMs) and Au-coated AAOMs (AAOM/Au) with pore diameters of 55 nm and inter-pore spacing of 100 nm are used to develop ZnO/AAOM and ZnO/ZnAl2O4/Au nanoarrays of different morphologies. The effects of the electrodeposition current, time, barrier layer, and Au coating on the morphology of the resultant nanostructures were investigated using field emission scanning electron microscopy. Energy dispersive X-ray and X-ray diffraction were used to analyze the structural parameters and elemental composition of the ZnO/ZnAl2O4/Au nanoarray, and the Kirkendall effect was confirmed. The developed ZnO/ZnAl2O4/Au electrode was applied to remove organic dyes from aqueous solutions, including methylene blue (MB) and methyl orange (MO). Using a 3 cm2 ZnO/ZnAl2O4/Au sample, the 100% dye removal for 20 ppm MB and MO dyes at pH 7 and 25 °C was achieved after approximately 50 and 180 min, respectively. According to the kinetics analysis, the pseudo-second-order model controls the dye adsorption onto the sample surface. AAOM/Au and ZnO/ZnAl2O4/Au nanoarrays are also used as pH sensor electrodes. The sensing capability of AAOM/Au showed Nernstian behavior with a sensitivity of 65.1 mV/pH (R2 = 0.99) in a wide pH range of 2-9 and a detection limit of pH 12.6, whereas the ZnO/ZnAl2O4/Au electrode showed a slope of 40.1 ± 1.6 mV/pH (R2 = 0.996) in a pH range of 2-6. The electrode's behavior was more consistent with non-Nernstian behavior over the whole pH range under investigation. The sensitivity equation was given by V(mV) = 482.6 + 372.6 e-0.2095 pH at 25 °C with R2 = 1.0, which could be explained in terms of changes in the surface charge during protonation and deprotonation.

Adsorption of Methylene Blue Dye by Cetyltrimethylammonium Bromide Intercalated Polyaniline-Functionalized Montmorillonite Clay Nanocomposite: Kinetics, Isotherms, and Mechanism Study

In this study, new adsorbents were prepared by modifying a montmorillonite clay (Mt) with cethyltrimethyl ammonium bromide (CTAB) to form CTAB-Mt, followed by a second modification process with polyaniline (PAni) to form PAni@CTAB-Mt by in situ polymerization of aniline. X-ray diffraction (XRD), X-ray fluorescence spectroscopy (XRF), X-ray photoelectron spectroscopy (XPS), thermogravimetric analysis (TGA), transmission electron microscopy (TEM), cyclic voltammetry (CV) and the Brunauer-Emmett-Teller (BET) technique were used to characterize the samples. These adsorbents were used in a batch process to remove methylene blue (MB) from aqueous solution. Factors investigated included initial pH of the solution, contact time and temperature. The adsorption data fit the Freundlich isotherm better than the Langmuir and Temkin isotherms. The maximum adsorption capacities (qeq) obtained were 108.82 mg·g-1, 71.20 mg·g-1 and 57.36 mg·g-1 for PAni@CTAB-Mt, CTAB-Mt and Mt, respectively. The enhanced adsorption capability of the hybrid material is due to increase in surface area and pore volume of the PAni@CTAB-Mt adsorbent. The adsorption results were found to fit well with the pseudo-second-order kinetics model, with highest correlation coefficient (R2) values of 0.954, 0.942 and 0.958 for Mt, CTAB-Mt and PAni@CTAB-Mt adsorbents, respectively. The pH and temperature had a significant effect on the adsorption process, and the negative values of ΔG suggest that the adsorption process was spontaneous and feasible. The desorption and reusability experiment indicated that PAni@CTAB-Mt has the potential to be a reusable adsorbent for MB removal.

Versatile CO2-responsive Sponges Decorated with ZIF-8 for Bidirectional Separation of Oil/Water and Controllable Removal of Dyes

The complex wastewater containing water-soluble dyes and water-insoluble oils has given rise to significant environmental concerns that demand urgent remediation. Herein, a novel "smart" multifunctional sponge (ZIF-8@PMS) stepwise decorated with ZIF-8 nanoparticles and CO2-responsive copolymer (poly(2-(diethylamino) ethyl methacrylate-co-3-(trimethoxysilyl)propyl acrylate-co-stearyl methacrylate) was successfully prepared for CO2 controllable oil/water separation and dyes removal. The results revealed that the sponge coated with CO2-responsive copolymer for three cycles (ZIF-8@PMS-3) exhibited optimal comprehensive properties. The ZIF-8@PMS-3 had excellent compressive-resilient characteristics and chemical stability. As expected, it displayed tunable wettability and charged state under the regulation of CO2. Based on these features, ZIF-8@PMS-3 presented highly efficient removal of oil and dyes, even for the dye-containing oil/water emulsions, via a synergistic combination of adsorption and separation methods. The adsorption capacity for oil and various organic solvents ranged from 21.3 to 50 g g-1. The maximum adsorption capacities toward anionic dyes: methyl orange with 1205.89 mg g-1 and methyl blue with 880.00 mg g-1 in the presence of CO2 through electrostatic interaction. In the absence of CO2, it achieved maximum adsorption capacities for cationic dyes, including malachite green with 1246.15 mg g-1 and rhodamine B with 203 mg g-1, primarily driven by π-π interactions. According to distinct adsorption mechanisms, ZIF-8@PMS-3 could selectively adsorb either anionic or cationic dyes by exploiting CO2 as a trigger. Furthermore, the separation efficiencies for both types of oil/water emulsions surpassed 99.9%, with respective fluxes of 1566.99 L m-2 h-1 (water-in-oil emulsion) and 310.37 L m-2 h-1 (oil-in-water emulsion). Additionally, the as-prepared sponges exhibited remarkable antibacterial properties and exceptional recyclability. Therefore, the ZIF-8@PMS-3 holds substantial promise for potential applications in practical industrial wastewater treatment.

Development and Upscaling of SiO2@TiO2 Core-Shell Nanoparticles for Methylene Blue Removal

SiO2@TiO2 core-shell nanoparticles were successfully synthesized via a simple, reproducible, and low-cost method and tested for methylene blue adsorption and UV photodegradation, with a view to their application in wastewater treatment. The monodisperse SiO2 core was obtained by the classical Stöber method and then coated with a thin layer of TiO2, followed by calcination or hydrothermal treatments. The properties of SiO2@TiO2 core-shell NPs resulted from the synergy between the photocatalytic properties of TiO2 and the adsorptive properties of SiO2. The synthesized NPs were characterized using FT-IR spectroscopy, HR-TEM, FE-SEM, and EDS. Zeta potential, specific surface area, and porosity were also determined. The results show that the synthesized SiO2@TiO2 NPs that are hydrothermally treated have similar behaviors and properties regardless of the hydrothermal treatment type and synthesis scale and better performance compared to the SiO2@TiO2 calcined and TiO2 reference samples. The generation of reactive species was determined by EPR, and the photocatalytic activity was evaluated by the methylene blue (MB) removal in aqueous solution under UV light. Hydrothermally treated SiO2@TiO2 showed the highest adsorption capacity and photocatalytic removal of almost 100% of MB after 15 min in UV light, 55 and 89% higher compared to SiO2 and TiO2 reference samples, respectively, while the SiO2@TiO2 calcined sample showed 80%. It was also observed that the SiO2-containing samples showed a considerable adsorption capacity compared to the TiO2 reference sample, which improved the MB removal. These results demonstrate the efficient synergy effect between SiO2 and TiO2, which enhances both the adsorption and photocatalytic properties of the nanomaterial. A possible photocatalytic mechanism was also proposed. Also noteworthy is that the performance of the upscaled HT1 sample was similar to one of the lab-scale synthesized samples, demonstrating the potentiality of this synthesis methodology in producing candidate nanomaterials for the removal of contaminants from wastewater.

Valorization of Glucose-Derived Humin as a Low-Cost, Green, Reusable Adsorbent for Dye Removal, and Modeling the Process

Glucose can be isomerized into fructose and dehydrated into key platform biochemicals, following the "bio-refinery concept". However, this process generates black and intractable substances called humin, which possess a polymeric furanic-type structure. In this study, glucose-derived humin (GDH) was obtained by reacting D-glucose with an allylamine catalyst in a deep eutectic solvent medium, followed by a carbonization step. GDH was used as a low-cost, green, and reusable adsorbent for removing cationic methylene blue (MB) dye from water. The morphology of carbonized GDH differs from pristine GDH. The removal efficiencies of MB dye using pristine GDH and carbonized GDH were 52% and 97%, respectively. Temperature measurements indicated an exothermic process following pseudo-first-order kinetics, with adsorption behavior described by the Langmuir isotherm. The optimum parameters were predicted using the response surface methodology and found to be a reaction time of 600 min, an initial dye concentration of 50 ppm, and a GDH weight of 0.11 g with 98.7% desirability. The MB dye removal rate optimized through this model was 96.85%, which was in good agreement with the experimentally obtained value (92.49%). After 10 cycles, the MB removal rate remained above 80%, showcasing the potential for GDH reuse and cost-effective wastewater treatment.

Efficient Removal of Carcinogenic Azo Dyes from Water Using Iron(II) Clathrochelate Derived Metalorganic Copolymers Made from a Copper-Catalyzed [4 + 2] Cyclobenzannulation Reaction

A novel synthetic strategy is disclosed to prepare a new class of metalorganic copolymers that contain iron(II) clathrochelate building blocks by employing a mild and cost-effective copper-catalyzed [4 + 2] cyclobenzannulation reaction, using three specially designed diethynyl iron(II) clathrochelate synthons. The target copolymers CBP1-3 were isolated in high purity and excellent yields as proven by their structural and photophysical characterization, namely, Fourier transform infrared (FTIR), X-ray photoelectron spectroscopy (XPS) and UV-VIS absorption and emission spectroscopies. The thermogravimetric analysis (TGA) of CBP1-3 revealed an excellent chemical stability. Investigation of the adsorption properties of the target copolymers towards the carcinogenic methyl red dye from aqueous solution revealed a quantitative uptake in 30 min. Isothermal adsorption studies disclosed that methyl red uptake from aqueous solution followed the Langmuir model for all of the target copolymers, reaching a maximum adsorption capacity (q_m) of 431 mg g^-. Kinetic investigation revealed that the adsorption followed pseudo-first-order with an equilibrium adsorption capacity (q_e,cal) of 79.35 mg g^- and whose sorption property was sustained even after its reuse several times.

Novel Electrospun Composite Membranes Based on Polyhydroxybutyrate and Poly(vinyl formate) Loaded with Protonated Montmorillonite for Organic Dye Removal: Kinetic and Isotherm Studies

The use of biodegradable polyesters derived from green sources and their combination with natural abundantly layered aluminosilicate clay, e.g., natural montmorillonite, meets the requirements for the development of new sustainable, disposable, and biodegradable organic dye sorbent materials. In this regard, novel electrospun composite fibers, based on poly β-hydroxybutyrate (PHB) and in situ synthesized poly(vinyl formate) (PVF), loaded with protonated montmorillonite (MMT-H) were prepared via electrospinning in the presence of formic acid, a volatile solvent for polymers and a protonating agent for the pristine MMT-Na. The morphology and structure of electrospun composite fibers were investigated through SEM, TEM, AFM, FT-IR, and XRD analyses. The contact angle (CA) measurements showed increased hydrophilicity of the composite fibers incorporated with MMT-H. The electrospun fibrous mats were evaluated as membranes for removing cationic (methylene blue) and anionic (Congo red) dyes. PHB/MMT 20% and PVF/MMT 30% showed significant performance in dye removal compared with the other matrices. PHB/MMT 20% was the best electrospun mat for adsorbing Congo red. The PVF/MMT 30% fibrous membrane exhibited the optimum activity for the adsorption of methylene blue and Congo red dyes.

Investigation of the removal kinetics, thermodynamics and adsorption mechanism of anionic textile dye, Remazol Red RB, with powder pumice, a sustainable adsorbent from waste water

Excessive growth and abnormal use of dyes and water in the textile industry cause serious environmental problems, especially with excessive pollution of water bodies. Adsorption is an attractive, feasible, low-cost, highly efficient and sustainable technique in terms of green chemistry for the removal of pollutants from water. This study aims to investigate the removal kinetics, thermodynamics and adsorption mechanism of Remazol Red RB, which was chosen as a representative anionic reactive dye, from synthetic wastewater using powdered pumice, taking into account various experimental parameters such as initial dye concentration, adsorption time, temperature and pH. Moreover, to support the proposed adsorption mechanism, before and after adsorption of the samples, the Fourier transform infrared spectrophotometer (FTIR) spectra, X-ray powder diffraction (XRD) diffractograms and High resolution transmission electron microscopy (HRTEM) images were also taken and used. The results show that powder pumice can be an efficient adsorbent for anionic dye removal with a relatively high adsorption capacity of 38.90 mg/g, and it is very effective in 30-60 min in mild conditions. The experimental data showed a high agreement with the pseudo-second-order kinetic model and the Freundlich adsorption isotherm equation. In addition, thermodynamically, the process exhibited exothermic nature and standard isosteric enthalpy and entropy changes of -4.93 kJ/mol and 16.11 J/mol. K were calculated. It was determined that the adsorption mechanism was predominantly based on T-shaped pi-pi interactions and had physical characteristics.

Incorporation of graphene oxide nanosheets into polyethersulfone membranes to improve their separation performance and antifouling characteristics for Congo red removal

Due to worldwide shortage of water sources and, on the other hand, producing a huge amount of contaminated industrial wastewater, there is an urgent need to provide proper treatment processes such as fast-growing membrane ones. In this study, some nanocomposite nanofilter membranes, as a promising solution for this goal, were fabricated by incorporation of graphene oxide (GO) nanosheets into polyethersulfone (PES) membrane matrix and polyvinylpyrrolidone (PVP) via the method of non-solvent-induced phase separation (NIPS) to dedicate them higher separation performance and a higher antifouling tendency. The produced GO nanosheets and the prepared membranes' structure were evaluated by field-emission scanning electron microscopy (FESEM), X-ray diffraction (XRD), and atomic force microscopy (AFM) analysis. Then, the separation performance and antifouling characteristics of the prepared pristine and nanocomposite membranes were evaluated at 3 bar, 27°C, and Congo red (CR) dye concentrations of 50, 100, and 200 ppm. The observations revealed that the incorporation of GO nanosheets into the polymer matrix of PES-PVP increases the permeation flux, rejection of CR, and flux recovery ratio (FRR) to the maximum values of 276.4 L/m² .h, 99.5%, and 92.4%, respectively, at 0.4 wt.% loading of GO nanosheets as an optimum filler loading. PRACTITIONER POINTS: Graphene oxide nanosheets were prepared and uniformly incorporated in the polyethersulfone porous membrane. The nanocomposite membranes revealed higher separation performance, that is, permeation flux and dye rejection as 282.5 L/m² .h and 99.5% at 0.4 wt.% loading of GO nanosheets. Flux recovery ratio of the nanocomposite membrane, as their antifouling character, also increased as 92.4%, as the GO nanosheets were incorporated by 0.4 wt.%.

Silver Nanoparticles for Waste Water Management

Rapidly increasing industrialisation has human needs, but the consequences have added to the environmental harm. The pollution caused by several industries, including the dye industries, generates a large volume of wastewater containing dyes and hazardous chemicals that drains industrial effluents. The growing demand for readily available water, as well as the problem of polluted organic waste in reservoirs and streams, is a critical challenge for proper and sustainable development. Remediation has resulted in the need for an appropriate alternative to clear up the implications. Nanotechnology is an efficient and effective path to improve wastewater treatment/remediation. The effective surface properties and chemical activity of nanoparticles give them a better chance to remove or degrade the dye material from wastewater treatment. AgNPs (silver nanoparticles) are an efficient nanoparticle for the treatment of dye effluent that have been explored in many studies. The antimicrobial activity of AgNPs against several pathogens is well-recognised in the health and agriculture sectors. This review article summarises the applications of nanosilver-based particles in the dye removal/degradation process, effective water management strategies, and the field of agriculture.

Application of Unsupervised Learning for the Evaluation of Aerogels' Efficiency towards Dye Removal-A Principal Component Analysis (PCA) Approach

Water scarcity is a growing global issue, particularly in areas with limited freshwater sources, urging for sustainable water management practices to insure equitable access for all people. One way to address this problem is to implement advanced methods for treating existing contaminated water to offer more clean water. Adsorption through membranes technology is an important water treatment technique, and nanocellulose (NC)-, chitosan (CS)-, and graphene (G)- based aerogels are considered good adsorbents. To estimate the efficiency of dye removal for the mentioned aerogels, we intend to use an unsupervised machine learning approach known as "Principal Component Analysis". PCA showed that the chitosan-based ones have the lowest regeneration efficiencies, along with a moderate number of regenerations. NC2, NC9, and G5 are preferred where there is high adsorption energy to the membrane, and high porosities could be tolerated, but this allows lower removal efficiencies of dye contaminants. NC3, NC5, NC6, and NC11 have high removal efficiencies even with low porosities and surface area. In brief, PCA presents a powerful tool to unravel the efficiency of aerogels towards dye removal. Hence, several conditions need to be considered when employing or even manufacturing the investigated aerogels.

Chitosan/lemon residues activated carbon efficiently removal of acid red 18 from aqueous solutions: batch study, isotherm and kinetics

In this research, chitosan-decorated activated carbon (AC-CS) was proposed. The AC was cross-linked with glutaraldehyde to prepare an adsorbent (AC-CS). The AC-CS has a rough surface. Adding the AC-CS directly to the dye solution can achieve simple and convenient removal of anionic azo dyes acid red 18 (AR-18). In the dye solution, the AC-CS was used as an adsorbent. The effects of pH, contact time, temperature, initial concentration of AR-18 and the AC-CS dosage on the adsorption efficiency were investigated. Full kinetic and isotherm analyses were also undertaken. In addition, the reusability of the AC-CS was evaluated, and the results showed that the removal rate of AR18 after regeneration remained relatively stable, above 90%. This experiment has shown that AC-CS is a promising anionic azo dye adsorbent.

Fabrication and Characterization of Functional Biobased Membranes from Postconsumer Cotton Fabrics and Palm Waste for the Removal of Dyes

Textile industries currently face vast challenges for the active removal of colored wastewater. Indeed, sustainable, recyclable, and green approaches are still lacking to achieve this aim. Thus, the present study explored the utilization of highly functional, green, recyclable, fully bio-based, and cost-effective composite membranes from post-consumer cotton fabrics and palm waste for wastewater treatment purposes. Highly functional cellulose nanofibers (CNF) were produced from waste cotton fabrics and filter paper using an acid hydrolysis technique. The yield of nanofibers extracted from waste cotton fabrics and filter paper was 76.74 and 54.50%, respectively. The physical, chemical, and structural properties of nanofibers were studied using various advanced analytical techniques. The properties of isolated nanofibers were almost similar and comparable to those of commercial nanofibers. The surface charge densities were -94.0, -80.7, and -90.6 mV for the nanofibers of palm waste, cotton fibers, and filter paper, respectively. After membrane fabrication using vacuum and hot-pressing techniques, the characteristics of the membrane were analyzed. The results showed that the average pore size of the palm-waste membrane was 1.185 nm, while it was 1.875 nm for membrane from waste cotton fibers and filter paper. Congo red and methylene blue dyes were used as model solutions to understand the behavior of available functional groups and the surface ζ-potential of the membrane frameworks' interaction. The membrane made from palm waste had the highest dye removal efficiency, and it was 23% for Congo red and 44% for methylene blue. This study provides insights into the challenges associated with the use of postconsumer textile and agricultural waste, which can be potentially used in high-performance liquid filtration devices for a more sustainable society.

Graphene-Oxide-Grafted Natural Phosphate Support as a Low-Cost Ceramic Membrane for the Removal of Anionic Dyes from Simulated Textile Effluent

A novel natural phosphate/graphene oxide (GO) composite membrane was successfully fabricated using two steps: (i) silane chemical grafting and (ii) dip-coating of a GO solution. First, the low-cost disk ceramic support used in this work was fabricated out of Moroccan natural phosphate, and its properties were thoroughly characterized. The optimized ceramic support was sintered at 1100 °C following a specific heat treatment based on thermogravimetric analysis (TGA) and differential thermal analysis (DTA); it exhibited a permeability of 953.33 L/h·m²·bar, a porosity of 24.55%, an average pore size of 2.45 μm and a flexural strength of 22.46 MPa. The morphology analysis using SEM showed that the GO layer was homogenously coated on the crack-free Moroccan phosphate support with a thickness of 2.8 μm. The Fourier transform infrared spectrometer (FT-IR) results showed that modification with silane could improve the interfacial adhesion between the GO membrane and the ceramic support. After coating with GO on the surface, the water permeability was reduced to 31.93 L/h·m²·bar (i.e., by a factor of 142). The prepared GO/ceramic composite membrane exhibited good efficiency in the rejection of a toxic azo dye Congo Red (CR) (95.2%) and for a simulated dye effluent (87.6%) under industrial conditions. The multi-cycle filtration tests showed that the rejection rate of CR dye remained almost the same for four cycles. Finally, the flux recovery was also studied. After 1 h of water cleaning, the permeate flux recovered, increased significantly, and then remained stable.

Chitosan-Bead-Encapsulated Polystyrene Sulfonate for Adsorption of Methylene Blue and Regeneration Studies: Batch and Continuous Approaches

Textile industrialization causes water pollution due to the discharge of industrial effluents into the environment. To reduce the impact of industrial effluent, it must be treated in wastewater treatment plants before discharge into rivers. Among all wastewater treatment approaches, the adsorption process is one method to remove pollutants from wastewater, but it has some limitations in term of reusability and ionic selective adsorption properties. In this study, we prepared cationic poly (styrene sulfonate) (PSS)-incorporated anionic chitosan beads synthesized using the oil-water emulsion coagulation method. The produced beads were characterized using FESEM and FTIR analysis. In batch adsorption studies, the PSS-incorporated chitosan beads exhibited monolayer adsorption processes, that is, exothermic processes that occur spontaneously at low temperatures, which were analyzed based on the adsorption isotherms, adsorption kinetics, and thermodynamics model fittings. The presence of PSS enables cationic methylene blue dye to adsorb to the anionic chitosan structure via electrostatic interaction between the sulfonic group and the dye molecule. The maximum adsorption capacity of PSS-incorporated chitosan beads achieved 42.21 mg/g, as calculated from the Langmuir adsorption isotherm. Finally, the PSS-incorporated chitosan beads demonstrated good regeneration with different types of reagents, especially using sodium hydroxide as a regeneration reagent. With the use of sodium hydroxide regeneration of this adsorbent material, a continuous adsorption setup also demonstrated that PSS-incorporated chitosan beads can be reused for methylene blue adsorption for up to three cycle processes.

Removal of Methylene Blue from Water Using Magnetic GTL-Derived Biosolids: Study of Adsorption Isotherms and Kinetic Models

Global waste production is significantly rising with the increase in population. Efforts are being made to utilize waste in meaningful ways and increase its economic value. This research makes one such effort by utilizing gas-to-liquid (GTL)-derived biosolids, a significant waste produced from the wastewater treatment process. To understand the surface properties, the biosolid waste (BS) that is activated directly using potassium carbonate, labelled as KBS, has been characterized using scanning electron microscopy and energy dispersive X-ray spectroscopy (SEM-EDS), X-ray photoelectron spectroscopy (XPS), X-ray powder diffraction (XRD), and Brunauer-Emmett-Teller (BET). The characterization shows that the surface area of BS increased from 0.010 to 156 m²/g upon activation. The EDS and XPS results show an increase in the metal content after activation (especially iron); additionally, XRD revealed the presence of magnetite and potassium iron oxide upon activation. Furthermore, the magnetic field was recorded to be 0.1 mT using a tesla meter. The magnetic properties present in the activated carbon show potential for pollutant removal. Adsorption studies of methylene blue using KBS show a maximum adsorption capacity of 59.27 mg/g; the adsorption process is rapid and reaches equilibrium after 9 h. Modelling using seven different isotherm and kinetic models reveals the best fit for the Langmuir-Freundlich and Diffusion-chemisorptionmodels, respectively. Additional thermodynamic calculations conclude the adsorption system to be exothermic, spontaneous, and favoring physisorption.

Removal of Brilliant Green Dye from Water Using Ficus benghalensis Tree Leaves as an Efficient Biosorbent

The presence of dyes in water stream is a major environmental problem that affects aquatic and human life negatively. Therefore, it is essential to remove dye from wastewater before its discharge into the water bodies. In this study, Banyan (Ficus benghalensis, F. benghalensis) tree leaves, a low-cost biosorbent, were used to remove brilliant green (BG), a cationic dye, from an aqueous solution. Batch model experiments were carried out by varying operational parameters, such as initial concentration of dye solution, contact time, adsorbent dose, and pH of the solution, to obtain optimum conditions for removing BG dye. Under optimum conditions, maximum percent removal of 97.3% and adsorption capacity (Qe) value of 19.5 mg/g were achieved (at pH 8, adsorbent dose 0.05 g, dye concentration 50 ppm, and 60 min contact time). The Langmuir and Freundlich adsorption isotherms were applied to the experimental data. The linear fit value, R² of Freundlich adsorption isotherm, was 0.93, indicating its best fit to our experimental data. A kinetic study was also carried out by implementing the pseudo-first-order and pseudo-second-order kinetic models. The adsorption of BG on the selected biosorbent follows pseudo-second-order kinetics (R² = 0.99), indicating that transfer of internal and external mass co-occurs. This study surfaces the excellent adsorption capacity of Banyan tree leaves to remove cationic BG dye from aqueous solutions, including tap water, river water, and filtered river water. Therefore, the selected biosorbent is a cost-effective and easily accessible approach for removing toxic dyes from industrial effluents and wastewater.

Design of a new polyethersulfone nanofiltration membrane with anti-fouling properties using supported protic ionic liquid modification for dye/salt removal

Facile techniques to fabricate the nanofiltration membranes with ideal molecular sieving is one of the most interesting subjects in membrane separation technology. In this study, the application of modified graphene oxide (GO) with triethylenetetramine (TETA), CuFe₂ O₄ , and acetic acid (AC) (supported GO-TETA-CuFe₂ O₄ @AC) as a supported protic ionic liquid (PIL) modifier for polyethersulfone (PES) membrane was evaluated to approve the improvement of anti-fouling properties and wastewater rejection of the fabricated membranes. To enhance the key properties of graphene oxide, it was modified by hydrophilic nanomaterials (TETA-CuFe₂ O₄ ). High flux and promising flux recovery ratio (up to 95% compared to the unmodified membrane) can be observed in the modified membranes. The modified membranes by GO-TETA-CuFe₂ O₄ @AC were studied at optimum concentrations (0.5 wt.%) for salt rejection and different dyes. The obtained data indicated that the modified membranes by GO-TETA-CuFe₂ O₄ @AC indicated higher salt removal (up to 97% for BaCl₂ than the unmodified membrane), which was related to the efficient modification. The obtained pure water flux (PWF) for bare and optimal modified membrane from 13.11 to 27.87 kg/m² ·h, respectively. To exact evaluate the effect of membrane modification on performance examination, the modified membranes were evaluated for chlorine resistance testing. This study aimed to develop cost-effective nanofiltration (NF) membranes with high anti-fouling properties and to determine the maximum filtration capacity of in-time dyes and salts in effluents. PRACTITIONER POINTS: A GO-TETA-CuFe2O4 mixed matrix membrane was prepared for removal of salts and dyes. The effect of GO-TETA-CuFe2O4 enhanced the hydrophilicity and porosity. The membrane exhibited superior antifouling properties and ions rejection.

Starch Biocryogel for Removal of Methylene Blue by Batch Adsorption

A green monolithic starch cryogel was prepared and applied for the removal of methylene blue (MB) using a batch system. The influence of various experimental parameters on MB adsorption was investigated. High removal efficiency (81.58 ± 0.59%) and adsorption capacity (34.84 mg g^-1) were achieved. The Langmuir model better fitted the experimental data (determination coefficient (R²) = 0.9838) than the Freundlich one (R² = 0.8542), while the kinetics of MB adsorption on the cryogel followed a pseudo-second-order model. The adsorption process was spontaneous and endothermic with an activation energy of 37.8 kJ mol^-1 that indicated physical adsorption. The starch cryogel was used for MB removal from a wastewater sample collected from a local Batik production community enterprise in Phuket, Thailand, and a removal efficiency of 75.6% was achieved, indicating that it has a high potential as a green adsorbent for MB removal.

NIR light-propelled bullet-shaped carbon hollow nanomotors with controllable shell thickness for the enhanced dye removal

Materials with asymmetric nanostructures have attracted tremendous research attention due to their unique structural characteristics, excellent physicochemical properties, and promising prospects. However, it is still difficult to design and fabricate bullet-shaped nanostructure due to its structural complexity. Herein, for the first time, we successfully constructed NIR light-propelled bullet-shaped hollow carbon nanomotors (BHCNs) with an open mouth on the bottom of nano-bullet for the enhanced dye removal, by employing bullet-shaped silica nanoparticles (B-SiO₂ NPs) as a hard template. BHCNs were formed by the growth of polydopamine (PDA) layer on the heterogeneous surface of B-SiO₂ NPs, followed by the carbonization of PDA and subsequent selective etching of SiO₂. The shell thickness of BHCNs was able to be facilely controlled from ≈ 14 to 30 nm by tuning the added amount of dopamine. The combination of streamlined bullet-shaped nanostructure with good photothermal conversion efficiency of carbon materials facilitated the generation of asymmetric thermal gradient field around itself, thus driving the motion of BHCNs by self-thermophoresis. Noteworthily, the diffusion coefficient (De) and velocity of BCHNs with shell thickness of 15 nm (BHCNs-15) reached to 43.8 μm⋅cm^-2 and 11.4 μm⋅s^-1, respectively, under the illumination of 808 nm NIR laser with the power density of 1.5 W⋅cm^-2. The NIR laser propulsion caused BCHNs-15 to enhance the removal efficiency (53.4% vs. 25.4%) of methylene blue (MB) as a typical dye because the faster velocity could produce the higher micromixing role between carbon adsorbent and MB. Such a smart design of the streamlined nanomotors may provide a promising potential in environmental treatment, biomedical and biosensing applications.

Synthesis of Cellulose Nanocrystals/HKUST-1 Composites and Their Applications: Crystal Violet Removal and Doxorubicin Loading

This study developed a novel composite material containing cellulose nanocrystals (CNCs) and HKUST-1. Here, the addition of CNCs was used to enhance the characteristics of HKUST-1 in terms of surface area, adsorption ability, and functional groups. Here, the fabrication of CNCs@HKUST-1 composites was carried out by adding CNCs into the fabrication process of HKUST-1. The addition of CNCs provides additional functional groups on the surface of composite material which can be used to attach other organic compounds, such as in waste management and drug delivery systems. Here, CNCs@HKUST-1 composites were tested as a material for crystal violet (CV) removal and doxorubicin (DOX) loading. The removal capacity of CNCs@HKUST-1 composite towards CV molecules reached 1182.25 ± 27.74 mg/g, while the loading capacity for DOX drugs was around 1514.94 ± 11.67 mg/g. Both applications showed that CNCs@HKUST-1 composite had higher adsorption capacity and ability compared to its precursor materials, i.e., CNCs and HKUST-1.

Investigation of Citrus reticulata peels as an efficient and low-cost adsorbent for the removal of safranin orange dye

Safranin orange (SO) is a cationic dye widely used in industrial sectors. It becomes a threat to the aquatic ecosystem once it reaches water resources, directly affecting photosynthetic activity and dissolved oxygen rate. In view of this scenario and considering the large production of agro-industrial waste, which provides significant disposal costs and environmental impacts, the agricultural by-products such as mandarin peels (MP) are being used as biosorbent materials. Thus, this work proposed the use of MP for SO adsorption. The material was characterized by SEM, zeta potential, and FTIR analysis, in which it was possible to verify heterogeneous porous morphology, predominantly negative surface, and organic functional groups that facilitate adsorption. The results were promising, wherein the maximum adsorption capacity was 464 mg g^-1 (318 K), 0.4 g L^-1 adsorbent concentration, 120 min equilibrium time and removal percentage of 84.75%. The experimental data showed a better fit to the Langmuir and pseudo-second order mathematical models. The thermodynamic analysis inferred spontaneous, endothermic, and reversible character for SO adsorption onto MP. The main proposed adsorptive mechanisms were hydrogen bonds, π-interactions, and electrostatic interactions. In addition, the reuse of MP showed good efficiency since the adsorption capacity was maintained above 50% after four cycles (from 77.90 to 41.55 mg g^-1). Moreover, when evaluating the effect of pH and ionic strength, it verified that the adsorption efficiency was not reduced. Therefore, when compared with other materials, the versatility and potential applicability of MP as a low-cost adsorbent for wastewater treatment is notable.

Cellulose Nanofibers Derived Surface Coating in Enhancing the Dye Removal with Cellulosic Ultrafiltration Membrane

Commercially available ultrafiltration membranes were coated with cellulose nanofibers (CNFs) produced from softwood pulp by a two-step process: a non-derivatizing DES treatment and a simple mechanical treatment (high-speed homogenization and sonification). The CNFs coating aimed at enhancement of the removal of methylene blue (MB) from water and was investigated at different concentrations of the coating, quantified in grams of CNFs per square meter of the membrane (1.3, 6.5, 13, and 19.5 g/m²). The pure water permeability (PWP) was unaffected up to the concentration of 6.5 g/m² but the dye retention increased approximately 2.5-fold. Even higher improvement of MB removal, about 4-fold, was observed when 19.5 g/m² were used, however, the pure water permeability also decreased by about 30%. In addition, it was proved that the coating can be removed and created again several times which shows that the concept could be used to improve the retention of organic compounds when high permeability membranes are used.

Metal Oxide Hydrogel Composites for Remediation of Dye-Contaminated Wastewater: Principal Component Analysis

Water pollution is caused by multiple factors, such as industrial dye wastewater. Dye-contaminated water can be treated using hydrogels as adsorbent materials. Recently, composite hydrogels containing metal oxide nanoparticles (MONPs) have been used extensively in wastewater remediation. In this study, we use a statistical and artificial intelligence method, based on principal component analysis (PCA) with different applied parameters, to evaluate the adsorption efficiency of 27 different MONP composite hydrogels for wastewater dye treatment. PCA showed that the hydrogel composites CTS@Fe3O4, PAAm/TiO2, and PEGDMA-rGO/Fe3O4@cellulose should be used in situations involving high pH, time to reach equilibrium, and adsorption capacity. However, as the composites PAAm-co-AAc/TiO2, PVPA/Fe3O4@SiO2, PMOA/ATP/Fe3O4, and PVPA/Fe3O4@SiO2, are preferred when all physical and chemical properties investigated have low magnitudes. To conclude, PCA is a strong method for highlighting the essential factors affecting hydrogel composite selection for dye-contaminated water treatment.

Recent Advances in the Removal of Organic Dyes from Aqueous Media with Conducting Polymers, Polyaniline and Polypyrrole, and Their Composites

Water pollution by organic dyes, and its remediation, is an important environmental issue associated with ever-increasing scientific interest. Conducting polymers have recently come to the forefront as advanced agents for removing dye. The present review reports on the progress represented by the literature published in 2020–2022 on the application of conducting polymers and their composites in the removal of dyes from aqueous media. Two composites, incorporating the most important polymers, polyaniline, and polypyrrole, have been used as efficient dye adsorbents or photocatalysts of dye decomposition. The recent application trends are outlined, and future uses also exploiting the electrical and electrochemical properties of conducting polymers are offered.

Serratula coronata L. Mediated Synthesis of ZnO Nanoparticles and Their Application for the Removal of Alizarin Yellow R by Photocatalytic Degradation and Adsorption

In this study, the potential of biogenic zinc oxide nanoparticles (ZnO NPs) in the removal of alizarin yellow R (AY) from aqueous solutions by photocatalytic degradation, as well as adsorption, was investigated. The synthesized ZnO NPs were prepared by the simple wet-combustion method using the plant extract of Serratula coronata L. as a reducing and stabilizing agent and characterized by powder X-ray diffraction, scanning electron microscopy, energy dispersive X-ray and X-ray photoelectron spectroscopy. Photocatalytic degradation of AY was monitored by UV-visible spectroscopy and the effects of parameters, such as light source type (UV-, visible- and sunlight), incubation time, pH, catalyst dosage and temperature on degradation were investigated. It was demonstrated that the source of light plays an important role in the efficiency of the reaction and the UV-assisted degradation of AY was the most effective, compared to the others. The degradation reaction of AY was found to follow the Langmuir-Hinshelwood mechanism and a pseudo-first-order kinetic model. The degradation kinetics of AY accelerated with increasing temperature, and the lowest activation energy (E_a) was calculated as 3.4 kJ/mol for the UV-light irradiation system, while the E_a values were 4.18 and 7.37 kJ/mol for visible light and sunlight, respectively. The dye removal by the adsorption process was also affected by several parameters, such as pH, sorbent amount and contact time. The data obtained in the kinetics study fit the pseudo-second-order equation best model and the rate constant was calculated as 0.001 g/mg·min. The isotherm analysis indicated that the equilibrium data fit well with the Freundlich isotherm model. The maximum adsorption capacity of AY on biogenic ZnO NPs was 5.34 mg/g.

Adsorption of Safranin-O dye by copper oxide nanoparticles synthesized from Punica granatum leaf extract

The development of new technologies for water and wastewater treatment is a growing need due to the occurrence of micropollutants, such as dyes, in water resources. In this sense, green-synthesized nanoparticles are being extensively studied, due to their low cost, non-toxicity, and high efficiency in adsorption processes. Thus, the present study reports the green synthesis of copper oxide nanoparticles (CuO-NP), obtained from pomegranate (Punica granatum) leaf extract, employed for the removal of Safranin-O (SO) dye. CuO-NP was characterized by physicochemical analysis. These analyzes suggested that the redox process occurred efficiently. Also, the material presented interesting elements for the removal of cationic dyes such as negative surface charge, high specific surface area, and predominance of mesopores. The kinetic data fitted the pseudo-second-order model, reaching equilibrium in 480 min. The equilibrium study resulted in a maximum adsorption capacity of 189.54 mg g^-1 at 298 K and the experimental data best fitted the Langmuir model. The effect of pH and ionic strength did not present significant changes, which demonstrates an advantage of this adsorbent over other materials. The regeneration study allowed to verify the possibility of reuse CuO-NP, since after 4 cycles the adsorption capacity was 44% of the initial value. Considering the results found, CuO-NP has a high potential for applicability in the treatment of water contaminated by dyes.

Comparative Study of Three Dyes' Adsorption onto Activated Carbon from Chenopodium quinoa Willd and Quillaja saponaria

The present study shows porous activated carbon obtained from Chenopodium quinoa Willd and Quillaja saponaria and their use as potential adsorbents to remove three types of dyes from aqueous solutions. The adsorption results were compared with commercial charcoal to check their efficiency. All porous carbon materials were activated using carbon dioxide and steam and fully characterized. Moreover, the steam-activated samples exhibited a high total pore volume with a BET surface area of around 800 m2 g−1. Batch adsorption experiments showed that commercial charcoal is the charcoal that offered the best adsorption efficiency for tartrazine and sunset yellow FCF. However, in the case of crystal violet, all activated carbons obtained from Chenopodium quinoa Willd and Quillaja saponaria showed the best captures, outperforming commercial charcoal. Molecular dockings of the dyes on the commercial charcoal surface were performed using AutoDock Vina. The kinetic results of the three isotherm’s models for the present data follow the order: Langmuir~Freundlich > Temkin.

Thiourea-Isocyanate-Based Covalent Organic Frameworks with Tunable Surface Charge and Surface Area for Methylene Blue and Methyl Orange Removal from Aqueous Media

A thiourea hexamethylene diisocyanate covalent organic framework (TH COF) was synthesized by adjusting the surface charge and surface area. The surface charge value of TH COF, −3.8 ± 0.5 mV, can be changed to −29.1 ± 0.4 mV by treatment with NaOH (dp-TH) and 17.1 ± 1.0 mV by treatment with HCl (p-TH). Additionally, the surface area of TH COF was 39.3 m2/g, whereas the surface area of dp-TH COF and p-TH COF structures were measured as 41.4 m2/g and 42.5 m2/g, respectively. However, the COF structure had a better adsorption capability with acid and base treatments, e.g., dp-TH COF absorbed 5.5 ± 0.3 mg/g methylene blue (MB) dye, and p-TH COF absorbed 25.9 ± 1.4 mg/g methyl orange (MO) dye from 100 mL 25 ppm aqueous dye solutions, thereby increasing the MB and MO absorption amounts of the TH COF structure. Furthermore, by calculating the distribution, selectivity, and relative selectivity coefficients, the absorption capacity order was determined as dp-TH > TH > p-TH COFs for the MB dye, whereas it was p-TH > TH > dp-TH COFs for the MO dye. Finally, the reusability of dp-TH COF for MB absorption and p-TH COF for MO absorption were investigated. After five repeated uses, dp-TH COF retained 64.6 ± 3.7% of its absorption ability, whereas p-TH COF preserved 79.7 ± 3.2% of its absorption ability relative to the initial absorption amount.

Solid leather wastes as adsorbents for cationic and anionic dye removal

The removal of anionic and cationic dyes from aqueous solutions was investigated by different leather shavings, which are solid wastes generated in the leather industry. Wet-blue leather shavings (WB), vegetable-tanned leather shavings (VT), pickled hide (not tanned) shavings (PIC) and wet-white leather (pre-tanned) shavings (WW) were used. The cationic dye was Basic Red 2 and the anionic dye was Acid Brown 414. Point of zero charge, functional groups, shrinkage temperature and adsorbent surface area were characterized. The point of zero charge was 4.0, 6.0, 3.9 and 4.1 for WB, VT, PIC and WW, respectively. The specific surface area showed low values which was expected for this type of material. Tanning agent influence was verified through shrinkage temperature analysis of leather shavings. Main functional groups of the acid dye and the collagen structure of the solid wastes were determined. The tests with Basic Red 2 solutions showed only VT had a considerable removal for this cationic dye (96.7%). The tests with Acid Brown 414 were carried out with different contact times and adsorbent mass. Results showed high efficiency of WW and PIC, whose percentages of dye removal were above 96% at contact time of 30 min and above 90% using 20 mg of adsorbent. In this way, the final dye removal was 98.1% and 98.3% for contact time tests and 97.7% and 98% for adsorbent mass tests for WW and PIC, respectively. These results highlight the promising use of leather shavings as alternative adsorbents for the treatment of wastewater containing dyes.

Rapid Removal of Acid Red 88 by Zeolite/Chitosan Hydrogel in Aqueous Solution

In the present study, we developed a new adsorbent product with zeolite crosslinked chitosan (ZL–CH hydrogel) to remove acid red 88 (AR88) in an aqueous solution. The effects of several factors, such as the comparison of ZL–CH hydrogel and the absence of chitosan, pH, adsorbent dosage, initial AR88 concentration, contact time, and ion strength, were determined. Obtained results showed that ZL–CH hydrogel improved AR88 removal compared to the absence of chitosan, with an adsorption capacity of 332.48 mg/g in equilibrium time of 1 min, and adding ionic strength had no significant effect. However, with optimal conditions at pH 2.0, dry ZL–CH became hydrogel due to protonation of amino and hydroxyl groups through hydrogen bonds in the AR88 solution. Volume fraction and interaction force decreased with increasing porosity, leading to an increase in adsorption capacity and swelling ratio. Experimental data of the adsorption process showed the Freundlich isotherm model. The equilibrium for adsorption and swelling kinetics studies showed and fitted a pseudo-second-order model. NaOH was successful as a desorbing agent with 93.8%, and it followed the pseudo-second-order kinetics model. The recycling process indicates great potential for AR88 removal.

Trans-Cis Kinetic Study of Azobenzene-4,4'-dicarboxylic Acid and Aluminium and Zirconium Based Azobenzene-4,4'-dicarboxylate MOFs

Metal organic frameworks (MOFs) are porous hybrid crystalline materials that consist of organic linkers coordinated to metal centres. The trans–cis isomerisation kinetics of the azobenzene-4,4′-dicarboxylic acid (AZB(COOH)₂) precursor, as well as the Al³⁺ (Al-AZB)- and Zr⁴⁺ (Zr-AZB)-based MOFs with azobenzene-4,4′-dicarboxylate linkers, are presented. The photo-isomerization in the MOFs originates from singly bound azobenzene moieties on the surface of the MOF. The type of solvent used had a slight effect on the rate of isomerization and half-life, while the band gap energies were not significantly affected by the solvents. Photo-responsive MOFs can be classified as smart materials with possible applications in sensing, drug delivery, magnetism, and molecular recognition. In this study, the MOFs were applied in the dye adsorption of congo red (CR) in contaminated water. For both MOFs, the UV-irradiated cis isomer exhibited a slightly higher CR uptake than the ambient-light exposed trans isomer. Al-AZB displayed a dye adsorption capacity of over 95% for both the UV-irradiated and ambient light samples. The ambient light exposed Zr-AZB, and the UV irradiated Zr-AZB had 39.1% and 44.6% dye removal, respectively.

Degradation of methylene blue using Co-dopant of Mg and Se into hydroxyapatite composite

In this work, a comparative study of different Magnesium ions content was incorporated into hydroxyapatite (HAP) modified with selenite ions aiming to develop the degradation performance of methylene blue. Although the dopant metal (Mg²⁺ ) has a relatively low ratio, it makes a change in microstructure, morphology, surface area, external surface charge, particle size, and degradation performance. The effect of magnesium and selenium binary doping on microstructural and degradation of methylene blue has been evaluated. The external surface charge measured by zeta potential clarified that the highest negativity was -11.8 mV and it was accomplished in 1.0Mg/Se-HAP. Also, the roughness average grew from 36.8 nm reaching 59.2 nm upon the additional Mg (II). Moreover, TEM micrographs showed that compositions were formed in rod shapes. The process of degradation are optimized, showing effectiveness in methylene blue (MB) degradation of 62.4 % after 150 min of exposure to visible light. Electrostatic attraction and H-bonding and coordination have a vital role in the adsorption process. The recyclability of the as-prepared compositions exhibited that the effectiveness has been reduced to be about 54.2 % after five times of re-using.

Sustainable Development of Magnetic Chitosan Core-Shell Network for the Removal of Organic Dyes from Aqueous Solutions

The wide use of alizarin red S (ARS), a typical anthraquinone dye, has led to its continued accumulation in the aquatic environment, which causes mutagenic and carcinogenic effects on organisms. Therefore, this study focused on the removal of ARS dye by adsorption onto a magnetic chitosan core-shell network (MCN). The successful synthesis of the MCN was confirmed by ATR-FTIR, SEM, and EDX analysis. The influence of several parameters on the removal of ARS dye by the MCN revealed that the adsorption process reached equilibrium after 60 min, pH played a major role, and electrostatic interactions dominated for the ARS dye removal under acidic conditions. The adsorption data were described well by the Langmuir isotherm and a pseudo-second order kinetic model. In addition to the preferable adsorption of hydrophobic dissolved organic matter (DOM) fractions onto the MCN, the electrostatic repulsive forces between the previously adsorbed DOM onto MCN and ARS dye resulted in lower ARS dye removal. Furthermore, the MCN could easily be regenerated and reused for up to at least five cycles with more than 70% of its original efficiency. Most importantly, the spent MCN was pyrolytically converted into N-doped magnetic carbon and used as an adsorbent for various dyes, thus establishing a waste-free adsorption process.

Fabrication of recyclable magnetic biosorbent from eggshell membrane for efficient adsorption of dye

Magnetic eggshell membrane powder (MESM-P) were synthesized and used to remove Congo red (CR) dye from wastewater. The biosorption performance were evaluated at varying operating conditions, including initial pH, dye concentrations, contact time, and temperatures. Thekinetics studies revealed that the adsorption process can be better described by the pseudo-second-order model. The adsorption process conformed better to the Langmuir model with a maximum biosorption capacity of 1037.02 mg g^-1 _. An ethanol-water system was employed as a fast, effective and harmless desorptionsolvent for the regeneration of biosorbent. The system of 70% ethanol-30%water atpH 13 presented the maximum desorption efficiency up to 96.16%. The MESM-P could be easily regenerated and remained a high adsorption efficiency of 79.55% after ten reusing cycles. Therefore, the prepared MESM-P biosorbent could be a promising candidate for the removal of dye pollution from wastewater.