Preparation and characterisation of poly(lactide-co-glycolide) (PLGA) and PLGA/Bioglass® composite tubular foam scaffolds for tissue engineering applications

Tunable Release of Calcium from Chitosan-Coated Bioglass

Bioglass presents a standard biomaterial for regeneration of hard tissues in orthopedics and dentistry. The notable osteo-inductive properties of bioglass are largely due to the release of calcium ions from it. However, this release is not easily controllable and can often be excessive, especially during the initial interaction of the biomaterial with the surrounding tissues. Consequently, this excessive release can deplete the calcium content of the bioglass, ultimately reducing its overall bioactivity. In this study, we have tested if applying biopolymer chitosan coatings of different thicknesses would be able to mitigate and regulate the calcium ion release from monodisperse bioglass nanoparticles. Calcium release was assessed for four different chitosan coating thicknesses at different time points over the period of 28 days using a fluorescence quencher. Expectedly, chitosan-coated particles released less calcium as the concentration of chitosan in the coating solution increased, presumably due to the increased thickness of the chitosan coating around the bioglass particles. The mechanism of release remained constant for each coating thickness, corresponding to anomalous, non-Fickian diffusion, but the degree of anomalousness increased with the deposition of chitosan. Zeta potential testing showed an expected increase in the positive double layer charge following the deposition of the chitosan coating due to the surface exposure of the amine groups of chitosan. Less intuitively, the zeta potential became less positive as thickness of the chitosan coating increased, attesting to the lower density of the surface charges within thicker coatings than within the thinner ones. Overall, the findings of this study demonstrate that chitosan coating efficiently prevents the early release of calcium from bioglass. This coating procedure also allows for the tuning of the calcium release kinetics by controlling the chitosan concentration in the parent solution.

Oxygen-Deficient Bioceramics: Combination of Diagnosis, Therapy, and Regeneration

The journey of ceramics in medicine has been synchronized with an evolution from the first generation-alumina, zirconia, etc.-to the third -3D scaffolds. There is an up-and-coming member called oxygen-deficient or colored bioceramics, which have recently found their way through biomedical applications. The oxygen vacancy steers the light absorption toward visible and near infrared regions, making the colored bioceramics multifunctional-therapeutic, diagnostic, and regenerative. Oxygen-deficient bioceramics are capable of turning light into heat and reactive oxygen species for photothermal and photodynamic therapies, respectively, and concomitantly yield infrared and photoacoustic images. Different types of oxygen-deficient bioceramics have been recently developed through various synthesis routes. Some of them like TiO2- x , MoO3- x , and WOx have been more investigated for biomedical applications, whereas the rest have yet to be scrutinized. The most prominent advantage of these bioceramics over the other biomaterials is their multifunctionality endowed with a change in the microstructure. There are some challenges ahead of this category discussed at the end of the present review. By shedding light on this recently born bioceramics subcategory, it is believed that the field will undergo a big step further as these platforms are naturally multifunctional.

Safe-by-Design Antibacterial Peroxide-Substituted Biomimetic Apatites: Proof of Concept in Tropical Dentistry

Bone infections are a key health challenge with dramatic consequences for affected patients. In dentistry, periodontitis is a medically compromised condition for efficient dental care and bone grafting, the success of which depends on whether the surgical site is infected or not. Present treatments involve antibiotics associated with massive bacterial resistance effects, urging for the development of alternative antibacterial strategies. In this work, we established a safe-by-design bone substitute approach by combining bone-like apatite to peroxide ions close to natural in vivo oxygenated species aimed at fighting pathogens. In parallel, bone-like apatites doped with Ag⁺ or co-doped Ag⁺/peroxide were also prepared for comparative purposes. The compounds were thoroughly characterized by chemical titrations, FTIR, XRD, SEM, and EDX analyses. All doped apatites demonstrated significant antibacterial properties toward four major pathogenic bacteria involved in periodontitis and bone infection, namely Porphyromonas gingivalis (P. gingivalis), Aggregatibacter actinomycetemcomitans (A. actinomycetemcomitans), Fusobacterium nucleatum (F. nucleatum), and S. aureus. By way of complementary tests to assess protein adsorption, osteoblast cell adhesion, viability and IC₅₀ values, the samples were also shown to be highly biocompatible. In particular, peroxidated apatite was the safest material tested, with the lowest IC₅₀ value toward osteoblast cells. We then demonstrated the possibility to associate such doped apatites with two biocompatible polymers, namely gelatin and poly(lactic-co-glycolic) acid PLGA, to prepare, respectively, composite 2D membranes and 3D scaffolds. The spatial distribution of the apatite particles and polymers was scrutinized by SEM and µCT analyses, and their relevance to the field of bone regeneration was underlined. Such bio-inspired antibacterial apatite compounds, whether pure or associated with (bio)polymers are thus promising candidates in dentistry and orthopedics while providing an alternative to antibiotherapy.

Multifarious applications of bioactive glasses in soft tissue engineering

Tissue engineering (TE), a new paradigm in regenerative medicine, repairs and restores the diseased or damaged tissues and eliminates drawbacks associated with autografts and allografts. In this context, many biomaterials have been developed for regenerating tissues and are considered revolutionary in TE due to their flexibility, biocompatibility, and biodegradability. One such well-documented biomaterial is bioactive glasses (BGs), known for their osteoconductive and osteogenic potential and their abundant orthopedic and dental clinical applications. However, in the last few decades, the soft tissue regenerative potential of BGs has demonstrated great promise. Therefore, this review comprehensively covers the biological application of BGs in the repair and regeneration of tissues outside the skeleton system. BGs promote neovascularization, which is crucial to encourage host tissue integration with the implanted construct, making them suitable biomaterial scaffolds for TE. Moreover, they heal acute and chronic wounds and also have been reported to restore the injured superficial intestinal mucosa, aiding in gastroduodenal regeneration. In addition, BGs promote regeneration of the tissues with minimal renewal capacity like the heart and lungs. Besides, the peripheral nerve and musculoskeletal reparative properties of BGs are also reported. These results show promising soft tissue regenerative potential of BGs under preclinical settings without posing significant adverse effects. Albeit, there is limited bench-to-bedside clinical translation of elucidative research on BGs as they require rigorous pharmacological evaluations using standardized animal models for assessing biomolecular downstream pathways.

Building Scaffolds for Tubular Tissue Engineering

Hollow organs and tissue systems drive various functions in the body. Many of these hollow or tubular systems, such as vasculature, the intestines, and the trachea, are common targets for tissue engineering, given their relevance to numerous diseases and body functions. As the field of tissue engineering has developed, numerous benchtop models have been produced as platforms for basic science and drug testing. Production of tubular scaffolds for different tissue engineering applications possesses many commonalities, such as the necessity for producing an intact tubular opening and for formation of semi-permeable epithelia or endothelia. As such, the field has converged on a series of manufacturing techniques for producing these structures. In this review, we discuss some of the most common tissue engineered applications within the context of tubular tissues and the methods by which these structures can be produced. We provide an overview of the general structure and anatomy for these tissue systems along with a series of general design criteria for tubular tissue engineering. We categorize methods for manufacturing tubular scaffolds as follows: casting, electrospinning, rolling, 3D printing, and decellularization. We discuss state-of-the-art models within the context of vascular, intestinal, and tracheal tissue engineering. Finally, we conclude with a discussion of the future for these fields.

Bioactive Glasses: A Promising Therapeutic Ion Release Strategy for Enhancing Wound Healing

The morbidity, mortality, and burden of burn victims and patients with severe diabetic wounds are still high, which leads to an extensively growing demand for novel treatments with high clinical efficacy. Biomaterial-based wound treatment approaches have progressed over time from simple cotton wool dressings to advanced skin substitutes containing cells and growth factors; however, no wound care approach is yet completely satisfying. Bioactive glasses are materials with potential in many areas that exhibit unique features in biomedical applications. Today, bioactive glasses are not only amorphous solid structures that can be used as a substitute in hard tissue but also are promising materials for soft tissue regeneration and wound healing applications. Biologically active elements such as Ag, B, Ca, Ce, Co, Cu, Ga, Mg, Se, Sr, and Zn can be incorporated in glass networks; hence, the superiority of these multifunctional materials over current materials results from their ability to release multiple therapeutic ions in the wound environment, which target different stages of the wound healing process. Bioactive glasses and their dissolution products have high potency for inducing angiogenesis and exerting several biological impacts on cell functions, which are involved in wound healing and some other features that are valuable in wound healing applications, namely hemostatic and antibacterial properties. In this review, we focus on skin structure, the dynamic process of wound healing in injured skin, and existing wound care approaches. The basic concepts of bioactive glasses are reviewed to better understand the relationship between glass structure and its properties. We illustrate the active role of bioactive glasses in wound repair and regeneration. Finally, research studies that have used bioactive glasses in wound healing applications are summarized and the future trends in this field are elaborated.

Advancing bioinks for 3D bioprinting using reactive fillers: A review

The growing demand for personalized implants and tissue scaffolds requires advanced biomaterials and processing strategies for the fabrication of three-dimensional (3D) structures mimicking the complexity of the extracellular matrix. During the last years, biofabrication approaches like 3D printing of cell-laden (soft) hydrogels have been gaining increasing attention to design such 3D functional environments which resemble natural tissues (and organs). However, often these polymeric hydrogels show poor stability and low printing fidelity and hence various approaches in terms of multi-material mixtures are being developed to enhance pre- and post-printing features as well as cytocompatibility and post-printing cellular development. Additionally, bioactive properties improve the binding to the surrounding (host) tissue at the implantation site. In this review we focus on the state-of-the-art of a particular type of heterogeneous bioinks, which are composed of polymeric hydrogels incorporating inorganic bioactive fillers. Such systems include isotropic and anisotropic silicates like bioactive glasses and nanoclays or calcium-phosphates like hydroxyapatite (HAp), which provide in-situ crosslinking effects and add extra functionality to the matrix, for example mineralization capability. The present review paper discusses in detail such bioactive composite bioink systems based on the available literature, revealing that a great variety has been developed with substantially improved bioprinting characteristics, in comparison to the pure hydrogel counterparts, and enabling high viability of printed cells. The analysis of the results of the published studies demonstrates that bioactive fillers are a promising addition to hydrogels to print stable 3D constructs for regeneration of tissues. Progress and challenges of the development and applications of such composite bioink approaches are discussed and avenues for future research in the field are presented. STATEMENT OF SIGNIFICANCE: Biofabrication, involving the processing of biocompatible hydrogels including cells (bioinks), is being increasingly applied for developing complex tissue and organ mimicking structures. A variety of multi-material bioinks is being investigated to bioprint 3D constructs showing shape stability and long-term biological performance. Composite hydrogel bioinks incorporating inorganic bioreactive fillers for 3D bioprinting are the subject of this review paper. Results reported in the literature highlight the effect of bioactive fillers on bioink properties, printability and on cell behavior during and after printing and provide important information for optimizing the design of future bioinks for biofabrication, exploiting the extra functionalities provided by inorganic fillers. Further functionalization with drugs/growth factors can target enhanced printability and local drug release for more specialized biomedical therapies.

Fabrication of fibrillated and interconnected porous poly(ε-caprolactone) vascular tissue engineering scaffolds by microcellular foaming and polymer leaching

This paper provides a method combining eco-friendly supercritical CO₂ microcellular foaming and polymer leaching to fabricate small-diameter vascular tissue engineering scaffolds.

Recent advances and future perspectives of sol–gel derived porous bioactive glasses: a review

Sol–gel derived bioactive glasses have been extensively explored as a promising and highly porous scaffold materials for bone tissue regeneration applications owing to their exceptional osteoconductivity, osteostimulation and degradation rates.

A comprehensive review of biodegradable synthetic polymer-ceramic composites and their manufacture for biomedical applications

The application of various materials in biomedical procedures has recently experienced rapid growth. One area that is currently receiving significant attention from the scientific community is the treatment of a number of different types of bone-related diseases and disorders by using biodegradable polymer-ceramic composites. Biomaterials, the most common materials used to repair or replace damaged parts of the human body, can be categorized into three major groups: metals, ceramics, and polymers. Composites can be manufactured by combining two or more materials to achieve enhanced biocompatibility and biomechanical properties for specific applications. Biomaterials must display suitable properties for their applications, about strength, durability, and biological influence. Metals and their alloys such as titanium, stainless steel, and cobalt-based alloys have been widely investigated for implant-device applications because of their excellent mechanical properties. However, these materials may also manifest biological issues such as toxicity, poor tissue adhesion and stress shielding effect due to their high elastic modulus. To mitigate these issues, hydroxyapatite (HA) coatings have been used on metals because their chemical composition is similar to that of bone and teeth. Recently, a wide range of synthetic polymers such as poly (l-lactic acid) and poly (l-lactide-co-glycolide) have been studied for different biomedical applications, owing to their promising biocompatibility and biodegradability. This article gives an overview of synthetic polymer-ceramic composites with a particular emphasis on calcium phosphate group and their potential applications in tissue engineering. It is hoped that synthetic polymer-ceramic composites such as PLLA/HA and PCL/HA will provide advantages such as eliminating the stress shielding effect and the consequent need for revision surgery.

Electrospun F18 Bioactive Glass/PCL-Poly (ε-caprolactone)-Membrane for Guided Tissue Regeneration

Barrier membranes that are used for guided tissue regeneration (GTR) therapy usually lack bioactivity and the capability to promote new bone tissue formation. However, the incorporation of an osteogenic agent into polymeric membranes seems to be the most assertive strategy to enhance their regenerative potential. Here, the manufacturing of composite electrospun membranes made of poly (ε-caprolactone) (PCL) and particles of a novel bioactive glass composition (F18) is described. The membranes were mechanically and biologically tested with tensile strength tests and tissue culture with MG-63 osteoblast-like cell line, respectively. The PCL-F18 composite membranes demonstrated no increased cytotoxicity and an enhanced osteogenic potential when compared to pure PCL membranes. Moreover, the addition of the bioactive phase increased the membrane tensile strength. These preliminary results suggested that these new membranes can be a strong candidate for small bone injuries treatment by GTR technique.

Porous Particle-Reinforced Bioactive Gelatin Scaffold for Large Segmental Bone Defect Repairing

Large segmental bone defect repairing remains a big challenge in clinics, and synthetic bone grafts suitable for this purpose are still highly demanded. In this article, hydrophilic composite scaffolds (bioactive hollow particle (BHP)-gel scaffold) composed of bioactive hollow nanoparticles and cross-linked gelatin have been developed. The bioactive nanoparticles have a porous structure as well as high specific surface area; thus, they interact strongly with gelatin to overcome the swelling problem that a hydrophilic polymer scaffold will usually face. With this combination, these BHP-gel scaffolds showed porous structure and mechanical properties similar to those of the cancellous bone. They also showed excellent bioactivity and cell growth promotion performance in vitro. The best of them, namely, 10BHP-gel scaffold, was evaluated in vivo on a rat femur model, where it was found that the 5 mm segmental bone defect almost healed with new bone tissue formed in 12 weeks and the scaffold itself degraded at the same time. Thus, 10BHP-gel scaffold may become a potential bone graft for large segmental bone defect healing in the future.

Potential of Bioactive Glasses for Cardiac and Pulmonary Tissue Engineering

Repair and regeneration of disorders affecting cardiac and pulmonary tissues through tissue-engineering-based approaches is currently of particular interest. On this matter, different families of bioactive glasses (BGs) have recently been given much consideration with respect to treating refractory diseases of these tissues, such as myocardial infarction. The inherent properties of BGs, including their ability to bond to hard and soft tissues, to stimulate angiogenesis, and to elicit antimicrobial effects, along with their excellent biocompatibility, support these newly proposed strategies. Moreover, BGs can also act as a bioactive reinforcing phase to finely tune the mechanical properties of polymer-based constructs used to repair the damaged cardiac and pulmonary tissues. In the present study, we evaluated the potential of different forms of BGs, alone or in combination with other materials (e.g., polymers), in regards to repair and regenerate injured tissues of cardiac and pulmonary systems.

Adipose derived delivery vehicle for encapsulated adipogenic factors

Hydrogels derived from adipose tissue extracellular matrix (AdECM) have shown potential in the ability to generate new adipose tissue in vivo. To further enhance adipogenesis, a composite adipose derived delivery system (CADDS) containing single- and double-walled dexamethasone encapsulated microspheres (SW and DW Dex MS) has been developed. Previously, our laboratory has published the use of Dex MS as an additive to enhance adipogenesis and angiogenesis in adipose tissue grafts. In the current work, AdECM and CADDS are extensively characterized, in addition to conducting in vitro cell culture analysis. Study results indicate the AdECM used for the CADDS has minimal cellular and lipid content allowing for gelation of its collagen structure under physiological conditions. Adipose-derived stem cell (ASC) culture studies confirmed biocompatibility with the CADDS, and adipogenesis was increased in experimental groups containing the hydrogel scaffold. In vitro studies of AdECM hydrogel containing microspheres demonstrated a controlled release of dexamethasone from SW and DW formulations. The delivery of Dex MS via an injectable hydrogel scaffold combines two biologically responsive components to develop a minimally, invasive, off-the-shelf biomaterial for adipose tissue engineering.

STATEMENT OF SIGNIFICANCE

Scientists and doctors have yet to develop an off-the-shelf product for patients with soft tissue defects. Recently, the use of adipose derived extracellular matrix (adECM) to generate new adipose tissue in vivo has shown great promise but individually, adECM still has limitations in terms of volume and consistency. The current work introduces a novel composite off-the-shelf construct comprised of an adECM-based hydrogel and dexamethasone encapsulated microspheres (Dex MS). The hydrogel construct serves not only as an injectable protein-rich scaffold but also a delivery system for the Dex MS for non-invasive application to the defect site. The methods and results presented are a progressive step forward in the field of adipose tissue engineering.

An injectable hydroxyapatite/poly(lactide-co-glycolide) composite reinforced by micro/nano-hybrid poly(glycolide) fibers for bone repair

Porous nanocomposite of hydroxyapatite/poly(lactide-co-glycolide) (HA/PLGA) is conventionally used in bone tissue engineering but seldom in load-bearing orthopedic applications due to poor mechanical property. This study aimed to fabricate an injectable ternary composite by incorporating different contents of poly(glycolide) (PGA) fibers (0, 30, 50 and 70wt%) into the nanocomposite HA/PLGA matrix as reinforcing fillers for bone tissue repair. The fibers were obtained from melt-spinning and fiber diameter ranged from 70nm to 191μm. The injectability, mechanical strength, solidification rate and cytotoxicity of injectable composites were characterized. All composites achieved the acceptable injectability under an injection force of 100N. The mechanical properties of composites were gradually enhanced by increasing PGA fiber contents. The compression strength of composite with 70wt% content of PGA fibers was up to 31.1MPa, which was four times stronger than that of composite without PGA fibers. In the solidification rate analysis, the compression strength of composites with 50 or 70wt% PGA fibers in immersion time of only 45min was similar to that of composite without fibers in immersion time of 4-5h. The MTT test showed that exceeding 70% cells could survive in the fourfold dilution of extract, and its cytotoxicity focused on the first 4h after immersing. This study have revealed that the PGA fiber-reinforced HA/PLGA composite is a promising candidate for orthopedic applications.

The use of nanoscaffolds and dendrimers in tissue engineering

To avoid tissue rejection during organ transplantation, research has focused on the use of tissue engineering to regenerate required tissues or organs for patients. The biomedical applications of hyperbranched, multivalent, structurally uniform, biocompatible dendrimers in tissue engineering include the mimicking of natural extracellular matrices (ECMs) in the 3D microenvironment. Dendrimers are unimolecular architects that can incorporate a variety of biological and/or chemical substances in a 3D architecture to actively support the scaffold microenvironment during cell growth. Here, we review the use of dendritic delivery systems in tissue engineering. We discuss the available literature, highlighting the 3D architecture and preparation of these nanoscaffolds, and also review challenges to, and advances in, the use dendrimers in tissue engineering. Advances in the manufacturing of dendritic nanoparticles and scaffold architectures have resulted in the successful incorporation of dendritic scaffolds in tissue engineering.

Biomedical Applications of Biodegradable Polyesters

The focus in the field of biomedical engineering has shifted in recent years to biodegradable polymers and, in particular, polyesters. Dozens of polyester-based medical devices are commercially available, and every year more are introduced to the market. The mechanical performance and wide range of biodegradation properties of this class of polymers allow for high degrees of selectivity for targeted clinical applications. Recent research endeavors to expand the application of polymers have been driven by a need to target the general hydrophobic nature of polyesters and their limited cell motif sites. This review provides a comprehensive investigation into advanced strategies to modify polyesters and their clinical potential for future biomedical applications.

Physicochemical properties and biocompatibility of PZL/PLGA/bioglass composite scaffolds for bone tissue engineering

Foamy poly(N_ε-Cbz-l-lysine)/poly(lactic-co-glycolic acid)/bioglass composite scaffolds had appropriate physicochemical properties, good biomineralization ability, excellent cytocompatibility and histocompatibility, and desirable osteogenic ability.

Bioceramics and Scaffolds: A Winning Combination for Tissue Engineering

In the last few decades, we have assisted to a general increase of elder population worldwide associated with age-related pathologies. Therefore, there is the need for new biomaterials that can substitute damaged tissues, stimulate the body’s own regenerative mechanisms, and promote tissue healing. Porous templates referred to as “scaffolds” are thought to be required for three-dimensional tissue growth. Bioceramics, a special set of fully, partially, or non-crystalline ceramics (e.g., calcium phosphates, bioactive glasses, and glass–ceramics) that are designed for the repair and reconstruction of diseased parts of the body, have high potential as scaffold materials. Traditionally, bioceramics have been used to fill and restore bone and dental defects (repair of hard tissues). More recently, this category of biomaterials has also revealed promising applications in the field of soft-tissue engineering. Starting with an overview of the fundamental requirements for tissue engineering scaffolds, this article provides a detailed picture on recent developments of porous bioceramics and composites, including a summary of common fabrication technologies and a critical analysis of structure–property and structure–function relationships. Areas of future research are highlighted at the end of this review, with special attention to the development of multifunctional scaffolds exploiting therapeutic ion/drug release and emerging applications beyond hard tissue repair.

Improved dimensional stability with bioactive glass fibre skeleton in poly(lactide-co-glycolide) porous scaffolds for tissue engineering

Bone tissue engineering requires highly porous three-dimensional (3D) scaffolds with preferable osteoconductive properties, controlled degradation, and good dimensional stability. In this study, highly porous 3D poly(d,l-lactide-co-glycolide) (PLGA) - bioactive glass (BG) composites (PLGA/BG) were manufactured by combining highly porous 3D fibrous BG mesh skeleton with porous PLGA in a freeze-drying process. The 3D structure of the scaffolds was investigated as well as in vitro hydrolytic degradation for 10weeks. The effect of BG on the dimensional stability, scaffold composition, pore structure, and degradation behaviour of the scaffolds was evaluated. The composites showed superior pore structure as the BG fibres inhibited shrinkage of the scaffolds. The BG was also shown to buffer the acidic degradation products of PLGA. These results demonstrate the potential of these PLGA/BG composites for bone tissue engineering, but the ability of this kind of PLGA/BG composites to promote bone regeneration will be studied in forthcoming in vivo studies.

Electrophoretic Deposition of Gelatin/Hydroxyapatite Composite Coatings onto a Stainless Steel Substrate

Biodegradable polymers and bioactive ceramics are being combined in a variety of novel materials for tissue engineering scaffolds. These composite systems, which combine the useful mechanical properties of polymers with the bioactivity of ceramics, seem to be a promising choice for bone tissue engineering. In recent years, the use of biopolymers that gelate on cooling has received a lot of attention with regards to the production of laminates and coatings. In this work, we report the incorporation of hydroxyapatite (HA) into a gelatin coating on stainless steel substrate using colloidal processing technology. A titania (Ti) buffer layer prepared by dip coating was inserted to improve the bonding strength between the HA/gelatin layer and stainless steel substrate. The suspensions, composed of 1 vol% of HA and three different additions of gelatin, were formulated with a focus on rheological properties for codeposition of both phases by electrophoretic deposition (EPD). The composite coatings performed by EPD were investigated in terms of deposition efficiency and kinetics over different deposition times. The EPD process was performed at both ambient temperature and the gelling temperature of the suspension. While at room temperature no electrophoretic growth of the layers was observed, the thermal gelation of gelatin promotes the growth of a homogeneous, well-adherent coating.

Review and the state of the art: Sol-gel and melt quenched bioactive glasses for tissue engineering

Biomaterial development is currently the most active research area in the field of biomedical engineering. The bioglasses possess immense potential for being the ideal biomaterials due to their high adaptiveness to the biological environment as well as tunable properties. Bioglasses like 45S5 has shown great clinical success over the past 10 years. The bioglasses like 45S5 were prepared using melt-quenching techniques but recently porous bioactive glasses have been derived through sol-gel process. The synthesis route exhibits marked effect on the specific surface area, as well as degradability of the material. This article is an attempt to provide state of the art of the sol-gel and melt quenched bioactive bioglasses for tissue regeneration. Fabrication routes for bioglasses suitable for bone tissue engineering are highlighted and the effect of these fabrication techniques on the porosity, pore-volume, mechanical properties, cytocompatibilty and especially apatite layer formation on the surface of bioglasses is analyzed in detail. Drug delivery capability of bioglasses is addressed shortly along with the bioactivity of mesoporous glasses. © 2015 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 104B: 1248-1275, 2016.

Bioactive glasses beyond bone and teeth: emerging applications in contact with soft tissues

The applications of bioactive glasses (BGs) have to a great extent been related to the replacement, regeneration and repair of hard tissues, such as bone and teeth, and there is an extensive bibliography documenting the role of BGs as bone replacement materials and in bone tissue engineering applications. Interestingly, many of the biochemical reactions arising from the contact of BGs with bodily fluids, in particular the local increase in concentration of various ions at the glass-tissue interface, are also relevant to mechanisms involved in soft tissue regeneration. An increasing number of studies report on the application of BGs in contact with soft tissues, aiming at exploiting the well-known bioactive properties of BGs in soft tissue regeneration and wound healing. This review focuses on research, sometimes involving preliminary in vitro studies but also in vivo evidence, that demonstrates the suitability of BGs in contact with tissues outside the skeletal system, which includes studies investigating vascularization, wound healing and cardiac, lung, nerve, gastrointestinal, urinary tract and laryngeal tissue repair using BGs in various forms of particulates, fibers and nanoparticles with and without polymer components. Potentially active mechanisms of interaction of BGs and soft tissues based on the surface bioreactivity of BGs and on biomechanical stimuli affecting the soft tissue-BG collagenous bonding are discussed based on results in the literature.

Bioactive organic/inorganic hybrids with improved mechanical performance

New sol–gel functionalized poly-ethylene glycol (PEGM)/SiO₂–CaO hybrids were prepared with interpenetrating networks of silica and PEGM through the formation of Si–O–Si bonds.

Surface transformations of Bioglass 45S5 during scaffold synthesis for bone tissue engineering

In physiological fluid, a layer of hydroxycarbonate apatite, similar to bone mineral, develops on the surface of Bioglass 45S5. Collagen from the surrounding tissue is adsorbed on this layer that attracts osteoblasts, and favors bone regrowth. Bioglass is therefore an osteoinductive material. Still, due to its brittleness, the glass alone cannot be used to heal large bone defects. To overcome this issue, Bioglass is used to form a composite scaffold with poly(D,L-lactide) (PDLLA), a biodegradable polymer. The goal of this work is to understand Bioglass reactivity throughout scaffold fabrication via a low-temperature route, the solvent casting and particulate leaching technique. Changes in Bioglass (especially its surface) are susceptible to occur both while in contact with the processing fluids and potentially through a reaction with the surrounding polymeric matrix. Here we analyzed the surface changes of three different Bioglass samples: (i) as-received, (ii) treated in solutions that parallel those used in scaffold fabrication, and (iii) extracted from the scaffolds. We showed that extracted, just like treated, Bioglass deviates from the as-received, but to a larger extent. X-ray photoelectron and infrared spectroscopy support the theory that Bioglass surface was modified not just through contact with the solutions in scaffold fabrication, but upon an interaction with the polymeric matrix. The polymer network slows down the Na(+)/H(+) exchange between Bioglass and water used to leach salt particles to create pores within the scaffold. Changes in surface properties affect the bioactivity of Bioglass and thus of the composite scaffolds, and are therefore critical to identify.

Effect of testosterone incorporation on cell proliferation and differentiation for polymer-bioceramic composites

In the current study, we characterized the polycaprolactone (PCL), poly(lactic acid-co-glycolic acid) (PLGA), and biphasic calcium phosphate (BCP) composites coated with testosterone propionate (T) using Fourier transform infrared spectroscopy (FTIR) and powder X-ray diffraction (XRD). Osteoblastic cells were seeded with PCL/BCP, PCL/BCP/T, PLGA/PCL/BCP and PLGA/PCL/BCP/T scaffolds, and cell viability, proliferation, differentiation and adhesion were analyzed. The results of physic-chemical experiments showed no displacements or suppression of bands in the FTIR spectra of scaffolds. The XRD patterns of the scaffolds showed an amorphous profile. The osteoblastic cells viability and proliferation increased in the presence of composites with testosterone over 72 h, and were significantly greater when PLGA/PCL/BCP/T scaffold was tested against PCL/BCP/T. Furthermore alkaline phosphatase production was significantly greater in the same group. In conclusion, the PLGA/PCL/BCP scaffold with testosterone could be a promising option for bone tissue applications due to its biocompatibility and its stimulatory effect on cell proliferation.

Bioactive starch-based scaffolds and human adipose stem cells are a good combination for bone tissue engineering

Silicon is known to have an influence on calcium phosphate deposition and on the differentiation of bone precursor cells. This study explores the effect of the incorporation of silanol (Si-OH) groups into polymeric scaffolds on the osteogenic differentiation of human adipose stem cells (hASC) cultured under dynamic and static conditions. A blend of corn starch with polycaprolactone (30/70 wt.%, SPCL) was used to produce three-dimensional fibre meshes scaffolds by the wet-spinning technique, and a calcium silicate solution was used as a non-solvent to develop an in situ functionalization with Si-OH groups. In vitro assessment, using hASC, of functionalized and non-functionalized scaffolds was evaluated in either α-MEM or osteogenic medium under static and dynamic conditions (provided by a flow perfusion bioreactor). The functionalized materials, SPCL-Si, exhibit the capacity to sustain cell proliferation and induce their differentiation into the osteogenic lineage. The formation of mineralization nodules was observed in cells cultured on the SPCL-Si materials. Culturing under dynamic conditions using a flow perfusion bioreactor was shown to enhance the hASC proliferation and differentiation and a better distribution of cells within the material. The present work demonstrates the potential of these functionalized materials for future applications in bone tissue engineering. Additionally, these results highlight the simplicity, economic and reliable production process of those materials.

Progress and challenges in biomaterials used for bone tissue engineering: bioactive glasses and elastomeric composites

Driven by the increasing economic burden associated with bone injury and disease, biomaterial development for bone repair represents the most active research area in the field of tissue engineering. This article provides an update on recent advances in the development of bioactive biomaterials for bone regeneration. Special attention is paid to the recent developments of sintered Na-containing bioactive glasses, borate-based bioactive glasses, those doped with trace elements (such as Cu, Zn, and Sr), and novel elastomeric composites. Although bioactive glasses are not new to bone tissue engineering, their tunable mechanical properties, biodegradation rates, and ability to support bone and vascular tissue regeneration, as well as osteoblast differentiation from stem and progenitor cells, are superior to other bioceramics. Recent progresses on the development of borate bioactive glasses and trace element-doped bioactive glasses expand the repertoire of bioactive glasses. Although boride and other trace elements have beneficial effects on bone remodeling and/or associated angiogenesis, the risk of toxicity at high levels must be highly regarded in the design of new composition of bioactive biomaterials so that the release of these elements must be satisfactorily lower than their biologically safe levels. Elastomeric composites are superior to the more commonly used thermoplastic-matrix composites, owing to the well-defined elastic properties of elastomers which are ideal for the replacement of collagen, a key elastic protein within the bone tissue. Artificial bone matrix made from elastomeric composites can, therefore, offer both sound mechanical integrity and flexibility in the dynamic environment of injured bone.

Gallium containing glass polyalkenoate anti-cancerous bone cements: glass characterization and physical properties

A gallium (Ga) glass series (0.48SiO(2)-0.40ZnO-0.12CaO, with 0.08 mol% substitution for ZnO) was developed to formulate a Ga-containing Glass Polyalkenoate Cement (GPC) series. Network connectivity (NC) and X-ray Photoelectron Spectroscopy (XPS) was employed to investigate the role of Ga(3+) in the glass, where it is assumed to act as a network modifier. Ga-GPC series was formulated with E9 and E11 polyacrylic acid (PAA) at 50, 55 and 60 wt% additions. E11 working times (T(w)) ranged from 68 to 96 s (Lcon.) and 106 s for the Ga-GPCs (LGa-1 and LGa-2). Setting times (T(s)) ranged from 104 to 226 s (Lcon.) and 211 s for LGa-1 and LGa-2. Compression (σc) and biaxial flexural (σf) testing were conducted where Lcon. increased from 62 to 68 MPa, LGa-1 from 14 to 42 MPa and LGa-2 from 20 to 47 MPa in σc over 1-30 days. σf testing revealed that Lcon. increased from 29 to 42 MPa, LGa-1 from 7 to 32 MPa and LGa-2 from 12 to 36 MPa over 1-30 days.

Effect of Si and Fe doping on calcium phosphate glass fibre reinforced polycaprolactone bone analogous composites

Reinforcing biodegradable polymers with phosphate-based glass fibres (PGF) is of interest for bone repair and regeneration. In addition to increasing the mechanical properties, PGF can also release bioinorganics, as they are water soluble, a property that may be controllably translated into a fully degradable composite. Herein, the effect of Si and Fe on the solubility of calcium-containing phosphate-based glasses (PG) in the system (50P(2)O(5)-40CaO-(10-x)SiO(2)-xFe(2)O(3), where x=0, 5 and 10 mol.%) were investigated. On replacing SiO(2) with Fe(2)O(3), there was an increase in the glass transition temperature and density of the PG, suggesting greater crosslinking of the phosphate chains. This significantly reduced the dissolution rates of degradation and ion release. Two PG formulations, 50P(2)O(5)-40CaO-10Fe(2)O(3) (Fe10) and 50P(2)O(5)-40CaO-5Fe(2)O(3)-5SiO(2) (Fe5Si5), were melt drawn into fibres and randomly incorporated into polycaprolactone (PCL). Initially, the flexural strength and modulus significantly increased with PGF incorporation. In deionized water, PCL-Fe(5)Si(5) displayed a significantly greater weight loss and ion release compared with PCL-Fe10. In simulated body fluid, brushite was formed only on the surface of PCL-Fe(5)Si(5). Dynamic mechanical analysis in phosphate buffered saline (PBS) at 37°C revealed that the PCL-Fe10 storage modulus (E') was unchanged up to day 7, whereas the onset of PCL-Fe(5)Si(5)E' decrease occurred at day 4. At longer-term ageing in PBS, PCL-Fe(5)Si(5) flexural strength and modulus decreased significantly. MC3T3-E1 preosteoblasts seeded onto PCL-PGF grew up to day 7 in culture. PGF can be used to control the properties of biodegradable composites for potential application as bone fracture fixation devices.

Effect of phosphate-based glass fibre surface properties on thermally produced poly(lactic acid) matrix composites

Incorporation of soluble bioactive glass fibres into biodegradable polymers is an interesting approach for bone repair and regeneration. However, the glass composition and its surface properties significantly affect the nature of the fibre-matrix interface and composite properties. Herein, the effect of Si and Fe on the surface properties of calcium containing phosphate based glasses (PGs) in the system (50P(2)O(5)-40CaO-(10-x)SiO(2)-xFe(2)O(3), where x = 0, 5 and 10 mol.%) were investigated. Contact angle measurements revealed a higher surface energy, and surface polarity as well as increased hydrophilicity for Si doped PG which may account for the presence of surface hydroxyl groups. Two PG formulations, 50P(2)O(5)-40CaO-10Fe(2)O(3) (Fe10) and 50P(2)O(5)-40CaO-5Fe(2)O(3)-5SiO(2) (Fe5Si5), were melt drawn into fibres and randomly incorporated into poly(lactic acid) (PLA) produced by melt processing. The ageing in deionised water (DW), mechanical property changes in phosphate buffered saline (PBS) and cytocompatibility properties of these composites were investigated. In contrast to Fe10 and as a consequence of the higher surface energy and polarity of Fe5Si5, its incorporation into PLA led to increased inorganic/organic interaction indicated by a reduction in the carbonyl group of the matrix. PLA chain scission was confirmed by a greater reduction in its molecular weight in PLA-Fe5Si5 composites. In DW, the dissolution rate of PLA-Fe5Si5 was significantly higher than that of PLA-Fe10. Dissolution of the glass fibres resulted in the formation of channels within the matrix. Initial flexural strength was significantly increased through PGF incorporation. After PBS ageing, the reduction in mechanical properties was greater for PLA-Fe5Si5 compared to PLA-Fe10. MC3T3-E1 preosteoblasts seeded onto PG discs, PLA and PLA-PGF composites were evaluated for up to 7 days indicating that the materials were generally cytocompatible. In addition, cell alignment along the PGF orientation was observed showing cell preference towards PGF.