Osteogenesis and angiogenesis properties of dental pulp cell on novel injectable tricalcium phosphate cement by silica doped

3D-printed polycaprolactone/tricalcium silicate scaffolds modified with decellularized bone ECM-oxidized alginate for bone tissue engineering

The treatment of large craniofacial bone defects requires more advanced and effective strategies than bone grafts since such defects are challenging and cannot heal without intervention. In this regard, 3D printing offers promising solutions through the fabrication of scaffolds with the required shape, porosity, and various biomaterials suitable for specific tissues. In this study, 3D-printed polycaprolactone (PCL)-based scaffolds containing up to 30 % tricalcium silicate (TCS) were fabricated and then modified by incorporation of decellularized bone matrix- oxidized sodium alginate (DBM-OA). The results showed that the addition of 20 % TCS increased compressive modulus by 4.5-fold, yield strength by 12-fold, and toughness by 15-fold compared to pure PCL. In addition, the samples containing TCS revealed the formation of crystalline phases with a Ca/P ratio near that of hydroxyapatite (1.67). Cellular experiment results demonstrated that TCS have improved the biocompatibility of PCL-based scaffolds. On day 7, the scaffolds modified with DBM and 20 % TCS exhibited 8-fold enhancement of ALP activity of placenta-derived mesenchymal stem/stromal cells (P-MSCs) compared to pure PCL scaffolds. The present study's results suggest that the incorporation of TCS and DBM-OA into the PCL-based scaffold improves its mechanical behavior, bioactivity, biocompatibility, and promotes mineralization and early osteogenic activity.

Effect of silicon-doped calcium phosphate cement on angiogenesis based on controlled macrophage polarization

Vascularization is an important early indicator of osteogenesis involving biomaterials. Bone repair and new bone formation are associated with extensive neovascularization. Silicon-based biomaterials have attracted widespread attention due to their rapid vascularization. Although calcium phosphate cement (CPC) is a mature substitute for bone, the application of CPC is limited by its slow degradation and insufficient promotion of neovascularization. Calcium silicate (CS) has been shown to stimulate vascular endothelial proliferation. Thus, CS may be added to CPC (CPC-CS) to improve the biocompatibility and neovascularization of CPC. In the early phase of bone repair (the inflammatory phase), macrophages accumulate around the biomaterial and exert both anti- and pro-inflammatory effects. However, the effect of CPC-CS on macrophage polarization is not known, and it is not clear whether the effect on neovascularization is mediated through macrophage polarization. In the present study, we explored whether silicon-mediated macrophage polarization contributes to vascularization by evaluating the CPC-CS-mediated changes in the immuno-environment under different silicate ion contents both in vivo and in vitro. We found that the silicon released from CPC-CS can promote macrophage polarization into the M2 phenotype and rapid endothelial neovascularization during bone repair. Dramatic neovascularization and osteogenesis were observed in mouse calvarial bone defects implanted with CPC-CS containing 60% CS. These findings suggest that CPC-CS is a novel biomaterial that can modulate immune response, promote endothelial proliferation, and facilitate neovascularization and osteogenesis. Thus, CPC-CS shows potential as a bone substitute material.

Biocompatibility of a HA/β-TCP/C Scaffold as a Pulp-Capping Agent for Vital Pulp Treatment: An In Vivo Study in Rat Molars

Bioceramic materials possess desirable biological properties, highlighting their non-reactivity and osteoconductivity. Their use has been extended in vital pulp treatment. The purpose of this study was to evaluate and compare the effects of beta-tricalcium phosphate (β-TCP), hydroxyapatite (HA), and collagen (C) scaffold with mineral trioxide aggregate (MTA) on the vital pulp of rat molars. Thirty-two molars of Sprague–Dawley rats underwent direct pulp capping with β-TCP/HA/C (n = 16) and MTA (n = 16). After 30 days, the following parameters were evaluated in the tested samples: the degree of pulp inflammation and pulp vitality, the presence of reparative dentin, the homogeneity of the odontoblastic layer, and the presence of pulp fibrosis. No statistically significant differences were observed between HA/β-TCP/C and MTA in terms of the degree of inflammation (p = 0.124). Significant differences were found in reparative dentin formation between the treatment groups (p = 0.0005). Dentin bridge formation was observed in the MTA-treated group. The local action of HA/β-TCP/C is similar to that of MTA when used as an agent for pulp vital treatment in terms of absence of inflammation and maintenance of pulp vitality, although there are significant differences between both materials regarding the formation of dentin bridges.

Thermal Oxide Layer Enhances Crystallinity and Mechanical Properties for Plasma-Sprayed Hydroxyapatite Biomedical Coatings

The stability of plasma-sprayed hydroxyapatite (HA) coatings on metallic implants in vivo remains a significant challenge for load-bearing orthopedic implants despite their excellent mechanical and osteoconductive properties. This study focuses on oxide layer formation on the surface of Ti6Al4V samples through furnace heating at 600, 700, and 800 °C for 10 min for optimization of the most effective oxide layer to increase plasma coating crystallinity and improve plasma coating bond strength with the metal surface. The 800 °C heat treatment shows an effective oxide layer which increases coating crystallinity from 64 to 75% and coating adhesive bond strength from 25.9 ± 2.3 to 30.7 ± 1.1 MPa, while simultaneously reducing the dissolution rate of HA coatings. The addition of biologically relevant dopants, MgO and SiO2, show negligible effects on crystallinity and adhesive bond strength on plasma-sprayed HA coatings and additionally show an enhancement effect on osteoblast proliferation and differentiation. Moreover, the inclusion of these additivess shows an increase in osteogenesis in a rat distal femur model after 6 and 10 weeks of implantation. Overall, this study provides a direct solution to improve the crystallinity, adhesive bond strength, and osteogenic properties of plasma-sprayed HA coatings on orthopedic implants that is more manufacturable and translational from research to an industrial scale.

Improving osteogenesis of calcium phosphate bone cement by incorporating with lysine: An in vitro study

Calcium phosphate bone cement (CPC) has attracted extensive interests from surgeons and material scientists. However, its actual application is still limited because of its poor osteogenesis. In this work, lysine, one of the essential components of proteins, was incorporated into the CPC to improve its osteogenesis ability. Effects of lysine on the phase, morphology, physicochemical properties, protein adsorption, lysine release and cytocompatibility of CPC were investigated. Results showed that lysine had no significant influence on the phase and morphology of the hydrated cements, but evidently raised the compressive strength, apparent porosity and setting time of the cements in a content-dependent manner of lysine. In contrast to the control, the lysine-incorporated CPCs had notably enhanced in vitro osteogenesis capability. It was supposed to be synergistically attributed to the improvements of fibronectin (FN) anchoring and bone mesenchymal stem cells (BMSCs) adhesion on the hydrated cements as well as the sustained release of bioactive amino acid molecules. Hence, lysine was expected to be applied as a novel bioactive admixture in the development of CPC with the improved osteogenesis ability and physicochemical properties for numerous orthopedic applications.

Enhancing the biological activity of vaterite-containing β-dicalcium silicate cement by silane coupling agent for biomaterials

Vaterite-containing β-dicalcium silicate powder (A-V-C₂S) was successfully grafting modified by 3-aminopropyltriethoxysilane (APTES) through reflux agitation. The purpose of this work is to fix the amino groups on the vaterite-containing β-dicalcium silicate (V-C₂S) powder's surface, which makes the powder's surface with positive charge, and further enhanced the combination with those negatively charged bioactive molecules or drugs to improve the performance of biomaterials. XRD and FT-IR analysis indicated that N-H groups were successfully grafted onto the surface of the V-C₂S sample on the basis of vaterite existence through the process of first grafting then carbonation. Moreover, the best grafting modification that refluxing at 70 °C for 12 h was determined through the quantitative analysis of N-H groups on V-C₂S powder's surface. The A-V-C₂S sample showed a better apatite formation ability after it was soaked in stimulated body fluid (SBF), indicating that good apatite mineralization. Moreover, the A-V-C₂S sample with weak alkali in implanting position could stimulate the attachment, proliferation and improve the activity of MC3T3-E1 cells. Experimental results demonstrated that, A-V-C₂S was expected to be a new biomaterial as bone repairing substitute.

Novel vaterite-containing tricalcium silicate bone cement by surface functionalization using 3-aminopropyltriethoxysilane: setting behavior, in vitro bioactivity and cytocompatibility

A novel vaterite-containing tricalcium silicate (V-C₃S) was grafted by 3-aminopropyltriethoxysilane (APTES), and the amino groups have been successfully fixed on the vaterite-containing tricalcium silicate powder's surface (after grafting the amino group, V-C₃S was named A-V-C₃S). The setting behavior, mechanical properties, porosity, weight loss and anti-washout properties of the tricalcium silicate (C₃S), V-C₃S and A-V-C₃S bone cement were systematically investigated. The in vitro induction of hydroxyapatite (HAp) formation of C₃S, V-C₃S and A-V-C₃S bone cement was confirmed by x-ray diffraction, Fourier-transform infrared spectroscopy and scanning electron microscopy. The cell viability, cell proliferation and cell attachment were investigated to assess the effects of bone cement on MC3T3-E1 cells. Results showed that the setting time of A-V-C₃S bone cement can meet the requirements of a clinical test, with improved anti-washout properties and an appropriate degradation rate. The pH value of the soaking solution was obviously decreased by surface modification. Besides, the morphology and fluorescence photograph results revealed that the A-V-C₃S bone cement showed an enhanced biocompatibility effect on the proliferation and attachment of MC3T3-E1 cells. The A-V-C₃S bone cement was expected to be a potential bone-substitute material.

Repair of rat calvarial defects using Si-doped hydroxyapatite scaffolds loaded with a bone morphogenetic protein-2-related peptide

Tissue engineering promises therapies ideal for treating conventional large bone injuries and defects. In the present study, we developed a novel Si-HA scaffold loaded with a synthetic BMP-2-related peptide, P28, and tested its ability to repair a critical-sized calvarial defect. We created a calvarial defect (5 mm in diameter) in the parietal bone of 32 rats and implanted one of the following biomaterials: No implant (control), Si-HA, P28/Si-HA, or rhBMP-2/Si-HA. As assessed by micro CT imaging and histological evaluations, the P28/Si-HA scaffold promoted bone recovery to a similar degree as the rhBMP-2/Si-HA scaffold. In addition, both P28/Si-HA and rhBMP-2/Si-HA promoted recovery better than Si-HA alone. The novel P28/Si-HA scaffold might represent a promising biomaterial for future bone tissue engineering applications. © 2016 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 34:1874-1882, 2016.

Fabrication and characterization of polycaprolactone and tricalcium phosphate composites for tissue engineering applications

Background/purpose

β-Tricalcium phosphate (β-TCP) is an osteoconductive material which has been used for clinical purposes for several years, as is polycaprolactone (PCL), which has already been approved for a number of medical and drug delivery devices. In this study we have incorporated various concentrations of β-TCP into PCL with the aim of developing an injectable, mechanically strong, and biodegradable material which can be used for medical purposes without organic solvents.

Materials and methods

This study assesses the physical and chemical properties of this material, evaluates the in vitro bioactivity of the PCL/β-TCP composites, and analyzes cell proliferation and osteogenic differentiation when using human bone marrow mesenchymal stem cells (hBMSCs).

Results

The results show that weight losses of approximately 5.3%, 12.1%, 18.6%, and 25.2%, were observed for the TCP0, TCP10, TCP30, and TCP50 composites after immersion in simulated body fluid for 12 weeks, respectively, indicating significant differences (P < 0.05). In addition, PCL/β-TCP composites tend to have lower contact angles (47 ± 1.5° and 58 ± 1.7° for TCP50 and TCP30, respectively) than pure PCL (85 ± 1.3°), which are generally more hydrophilic. After 7 days, a significant (22% and 34%, respectively) increase (P < 0.05) in alkaline phosphatase level was measured for TCP30 and TCP50 in comparison with the pure PCL.

Conclusion

PCL/TCP is biocompatible with hBMSCs. It not only promotes proliferation of hBMSCs but also helps to differentiate reparative hard tissue. We suggest 50% (weight) PCL-containing β-TCP biocomposites as the best choice for hard tissue repair applications.

Macrophage-mediated osteogenesis activation in co-culture with osteoblast on calcium silicate cement

The use of calcium silicate (CS) cement holds great promise for bone substitute biomaterials. However, the effects of CS on osteoblast and macrophage cells are not fully understood. This study examines cell proliferation and differentiation of mono- or co-cultured MC3T3-E1 and Raw 264.7 cells on CS cement. Very few studies to date have looked at the effects of osteoblast and macrophages on biomaterial-regulated osteogenesis. In this study the proliferation and differentiation of MC3T3-E1, Raw 264.7 and co-cultured MC3T3-E1/Raw 264.7 on CS cements have been analyzed using a PrestoBlue kit and ELISA. In addition, the effect of macrophages on CS-coordinated osteogenesis of MC3T3-E1 has been investigated. Results show that MC3T3-E1, Raw 264.7 and co-cultured MC3T3-E1/Raw 264.7 adhere to and proliferate well on the CS cement. In a co-culture, the CS cements inhibit receptor activator of nuclear factor kappa B ligand expression of both genes and proteins in Raw 264.7 cells when compared to those grown in mono-cultured system. Ca deposition of MC3T3-E1 in the co-culture is higher than that of cells in a mono-culture. Bone morphogenetic protein 2 (BMP2) is also significantly up-regulated by the CS cement stimulation, indicating that macrophages may participate in the CS stimulated osteogenesis. Interestingly, when macrophage are cultured with BMP2 receptor-blocking MC3T3-E1 on the CS cements, the osteogenesis differentiation of the cells is significantly inhibited, indicating the important role of macrophages in biomaterial-induced osteogenesis via BMP2 receptors. It is assumed that it is an increase in the secretion of the BMP2 from the Raw 264.7 cell that is primarily involved in the promotion of the osteogenesis of the MC3T3-E1. These results provide valuable insights into both the mechanism of CS-stimulated osteogenesis, and strategies to optimize the evaluation system for the in vitro osteogenesis capacity of bone substitute biomaterials.

Preparation of the fast setting and degrading Ca-Si-Mg cement with both odontogenesis and angiogenesis differentiation of human periodontal ligament cells

Develop a fast setting and controllable degrading magnesium-calcium silicate cement (Mg-CS) by sol-gel, and establish a mechanism using Mg ions to stimulate human periodontal ligament cells (hPDLs) are two purposes of this study. We have used the diametral tensile strength measurement to obtain the mechanical strength and stability of Mg-CS cement; in addition, the cement degradation properties is realized by measuring the releasing amount of Si and Mg ions in the simulated body fluid. The other cell characteristics of hPDLs, such as proliferation, differentiation and mineralization were examined while hPDLs were cultured on specimen surfaces. This study found out the degradation rate of Mg-CS cements depends on the Mg content in CS. Regarding in vitro bioactivity; the CS cements were covered with abundant clusters of apatite spherulites after immersion of 24h, while less apatite spherulites were formatted on the Mg-rich cement surfaces. In addition, the authors also explored the effects of Mg ions on the odontogenesis and angiogenesis differentiation of hPDLs in comparison with CS cement. The proliferation, alkaline phosphatase, odontogenesis-related genes (DSPP and DMP-1), and angiogenesis-related protein (vWF and ang-1) secretion of hPDLs were significantly stimulated when the Mg content of the specimen was increased. The results in this study suggest that Mg-CS materials with this modified composition could stimulate hPDLs behavior and can be good bioceramics for bone substitutes and hard tissue regeneration applications as they stimulate odontogenesis/angiogenesis.

Human Dental Pulp Cells Responses to Apatite Precipitation from Dicalcium Silicates

Unraveling the mechanisms behind the processes of cell attachment and the enhanced proliferation that occurs as a response to the presence of calcium silicate-based materials needs to be better understood so as to expand the applications of silicate-based materials. Ions in the environment may influence apatite precipitation and affect silicate ion release from silicate-based materials. Thus, the involvement of apatite precipitate in the regulation of cell behavior of human dental pulp cells (hDPCs) is also investigated in the present study, along with an investigation of the specific role of cell morphology and osteocalcin protein expression cultured on calcium silicate (CS) with different Dulbecco's modified Eagle's medium (DMEM). The microstructure and component of CS cement immersion in DMEM and P-free DMEM are analyzed. In addition, when hDPCs are cultured on CS with two DMEMs, we evaluate fibronectin (FN) and collagen type I (COL) secretion during the cell attachment stage. The facilitation of cell adhesion on CS has been confirmed and observed both by scanning with an electron microscope and using immunofluorescence imaging. The results indicate that CS is completely covered by an apatite layer with tiny spherical shapes on the surface in the DMEM, but not in the P-free DMEM. Compared to the P-free DMEM, the lower Ca ion in the DMEM may be attributed to the formation of the apatite on the surfaces of specimens as a result of consumption of the Ca ion from the DMEM. Similarly, the lower Si ion in the CS-soaked DMEM is attributed to the shielding effect of the apatite layer. The P-free DMEM group releases more Si ion increased COL and FN secretion, which promotes cell attachment more effectively than DMEM. This study provides new and important clues regarding the major effects of Si-induced cell behavior as well as the precipitated apatite-inhibited hDPC behavior on these materials.

Poly(Dopamine)-Assisted Immobilization of Xu Duan on 3D Printed Poly(Lactic Acid) Scaffolds to Up-Regulate Osteogenic and Angiogenic Markers of Bone Marrow Stem Cells

Three-dimensional printing is a versatile technique to generate large quantities of a wide variety of shapes and sizes of polymer. The aim of this study is to develop functionalized 3D printed poly(lactic acid) (PLA) scaffolds and use a mussel-inspired surface coating and Xu Duan (XD) immobilization to regulate cell adhesion, proliferation and differentiation of human bone-marrow mesenchymal stem cells (hBMSCs). We prepared PLA scaffolds and coated with polydopamine (PDA). The chemical composition and surface properties of PLA/PDA/XD were characterized by XPS. PLA/PDA/XD controlled hBMSCs' responses in several ways. Firstly, adhesion and proliferation of hBMSCs cultured on PLA/PDA/XD were significantly enhanced relative to those on PLA. In addition, the focal adhesion kinase (FAK) expression of cells was increased and promoted cell attachment depended on the XD content. In osteogenesis assay, the osteogenesis markers of hBMSCs cultured on PLA/PDA/XD were significantly higher than seen in those cultured on a pure PLA/PDA scaffolds. Moreover, hBMSCs cultured on PLA/PDA/XD showed up-regulation of the ang-1 and vWF proteins associated with angiogenic differentiation. Our results demonstrate that the bio-inspired coating synthetic PLA polymer can be used as a simple technique to render the surfaces of synthetic scaffolds active, thus enabling them to direct the specific responses of hBMSCs.

Poly(dopamine) coating of 3D printed poly(lactic acid) scaffolds for bone tissue engineering

3D printing is a versatile technique to generate large quantities of a wide variety of shapes and sizes of polymer. The aim of this study is to develop functionalized 3D printed poly(lactic acid) (PLA) scaffolds and use a mussel-inspired surface coating to regulate cell adhesion, proliferation and differentiation of human adipose-derived stem cells (hADSCs). We prepared PLA 3D scaffolds coated with polydopamine (PDA). The chemical composition and surface properties of PDA/PLA were characterized by XPS. PDA/PLA modulated hADSCs' responses in several ways. Firstly, adhesion and proliferation, and cell cycle of hADSCs cultured on PDA/PLA were significantly enhanced relative to those on PLA. In addition, the collagen I secreted from cells was increased and promoted cell attachment and cell cycle progression were depended on the PDA content. In osteogenesis assay, the ALP activity and osteocalcin of hADSCs cultured on PDA/PLA were significantly higher than seen in those cultured on pure PLA scaffolds. Moreover, hADSCs cultured on PDA/PLA showed up-regulation of the ang-1 and vWF proteins associated with angiogenic differentiation. Our results demonstrate that the bio-inspired coating synthetic PLA polymer can be used as a simple technique to render the surfaces of synthetic scaffolds active, thus enabling them to direct the specific responses of hADSCs.

The synergistic effects of Chinese herb and injectable calcium silicate/β-tricalcium phosphate composite on an osteogenic accelerator in vitro

This study investigates the physicochemical and biological effects of traditional Chinese medicines on the β-tricalcium phosphate (β-TCP)/calcium silicate (CS) composites of bone cells using human dental pulp cell. CS is an osteoconductive and bioactive material. For this research we have combined β-TCP and CS and check its effectiveness, a series of β-TCP/CS composites with different ratios of Xu Duan (XD) were prepared to make new bioactive and biodegradable biocomposites for bone repair. XD has been used in Traditional Chinese Medicine for hundreds of years as an antiosteoporosis, tonic and antiaging agent for the therapy of low back pain, traumatic hematoma, threatened abortion and bone fractures. Formation of bone-like apatite, the diametral tensile strength, and weight loss of composites were considered before and after immersion in simulated body fluid (SBF). In addition, we also examined the effects of XD released from β-TCP/CS composites and in vitro human dental pulp cell (hDPCs) and studied its behavior. The results show the XD-contained paste did not give any demixing when the weight ratio of XD increased to 5-10 % due to the filter-pressing effect during extrusion through the syringe. After immersion in SBF, the microstructure image showed a dense bone-like apatite layer covered on the β-TCP/CS/XD composites. In vitro cell experiments shows that the XD-rich composites promote human dental pulp cells (hDPCs) proliferation and differentiation. However, when the XD quantity in the composite is more than 5 %, the amount of cells and osteogenesis protein of hDPCs were stimulated by XD released from β-TCP/CS composites. The combination of XD in degradation of β-TCP and osteogenesis of CS gives strong reason to believe that these calcium-based composite cements may prove to be promising bone repair materials.

Effect of luteolin and apigenin on the expression of Oct-4, Sox2, and c-Myc in dental pulp cells with in vitro culture

Introduction. Dental pulp cells (DPCs) are promising cell source for dental tissue regeneration. Recently, small molecules which optimize microenvironment or activate the reprogramming network provide a new way to enhance the pluripotency. Two promising bioflavonoids luteolin and apigenin were reported to enhance reprogramming efficiency in mouse embryonic fibroblast (MEF). However, their effect and underlying mechanism in cell fate determination of human DPCs remain unclear. Methods. To elucidate the effect of luteolin and apigenin on the cell fate determination of DPCs, we explored the cell proliferation, cell cycle, senescence, apoptosis, expression of pluripotency markers Oct-4, Sox2, and c-Myc, and multilineage differentiation capability of DPCs with luteolin or apigenin treatment. Results. We demonstrated that luteolin and apigenin inhibited cell proliferation, arrested DPCs in G2/M and S phase, and upregulated PI value and apoptosis. Moreover, luteolin and apigenin increased telomerase activity, maintained DPCs in a presenescent state, and activated the expression of Oct-4, Sox2, and c-Myc at a dose- and time-dependent pattern in DPCs even at late passages, albeit repressed lineage-specific differentiation. Conclusions. Addition of luteolin and apigenin in the culture medium might provide an effective way to maintain DPCs in an undifferentiated stage and inhibit lineage-specific differentiation.

Stimulatory effects of the fast setting and suitable degrading Ca–Si–Mg cement on both cementogenesis and angiogenesis differentiation of human periodontal ligament cells

The purpose of this study is to develop a fast setting and suitable degrading Mg–calcium silicate cement (Mg–CS) and a mechanism using Mg ions to stimulate human periodontal ligament cells (hPDLCs).