Biocompatibility assessment of graphene oxide-hydroxyapatite coating applied on TiO2 nanotubes by ultrasound-assisted pulse electrodeposition

Incorporating mesoporous SiO2-HA particles into chitosan/hydroxyapatite scaffolds: A comprehensive evaluation of bioactivity and biocompatibility

In this work, composite scaffolds with various composition ratios of chitosan (CS), hydroxyapatite (HA), and mesoporous SiO2 particles co-synthesized with hydroxyapatite (SiO2-HA) were fabricated via the freeze-drying method for bone tissue engineering applications. Morphological studies showed that adding mesoporous particles resulted in a structure with a more uniformly porous geometry, subsequently leading to reduced biodegradation rates and water absorption in the scaffolds. The bioactivity results showed the introduction of mesoporous particles notably enhanced the coverage of the scaffold surface with apatite films. Moreover, biocompatibility assessments using sarcoma osteogenic cell line (SAOS-2) highlighted mesoporous particles' positive impact on cell adhesion and growth. The fluorescence images showed spindle-shaped cells with a greater number and normal cell nuclei for the scaffolds containing mesoporous SiO2-HA particles. The MTT cytotoxicity results indicated that the scaffolds containing mesoporous particles showed approximately 25 % higher cell survival more than single chitosan-based ones. What is more, the mesoporous-containing scaffolds occurred to have the best alkaline phosphatase test (ALP) activity among all scaffolds. It is important to add that CS/HA/mesoporous SiO2-HA scaffolds including SAOS-2 cells showed no sign of either early or late apoptosis. These findings affirm the potential of CS/HA/mesoporous SiO2-HA scaffolds as promising implants for bone tissue engineering.

Braided scaffolds with polypyrrole/polydopamine/hydroxyapatite coatings with electrical conductivity and osteogenic properties for bone tissue engineering

When impaired bones are grafted with bone scaffolds, the behaviors of osteoblast are dependent on the implant materials and surface morphology. To this end, we modulated the surface morphology of scaffolds that promote cell growth. In this study, ice-template and spraying method methods are employed to coat different proportions of PDA and PPy over the PLA/PVA weaving scaffolds, after which HA is Coated over via the electrochemical deposition, forming weaving scaffolds with electrically conductive PDA/PPy/HA coating. The test results indicate that with a PPy/PDA concentration ratio is 30, the PPy particles are more uniformly distributed on the fiber surface. The scaffolds are wrapped in a HA coating layer with a high purity, and calcium and phosphorus elements are evenly dispersed with a Ca/P ratio being 1.69. Owing to the synergistic effect between PDA and PPy coating, the scaffolds demonstrate excellent electrochemical stability and electrochemical activity. The biological activity of the scaffold increased to 274.66% under electrical stimulation. The new thinking proposed by this study extends the worth of applying textile structure to the medical field, the application of which highly increases the prospect of bone tissue engineering.

Tetracalcium phosphate/polycaprolactone composite scaffold: Mechanical reinforcement, biodegradability regulation and bioactivity induction

Polycaprolactone (PCL) is considered a potential biomaterial due to its good biocompatibility, but its slow degradability and insufficient mechanical properties limit its wide application in bone tissue engineering. Tetracalcium phosphate's (TTCP) good degradability and inherent high stiffness are expected to compensate for the aforementioned defects of PCL and endow it with good biological activity. This goal of this study was to obtain bioactive PCL composite scaffolds with tuneable degradation properties and good mechanical strength via selective laser sintering technology (SLS). Composite porous scaffolds with TTCP contents of 0%, 5%, 10%, 15%, 20%, and 25% were prepared, and the experimental results showed that the addition of TTCP significantly improved the mechanical properties of the scaffold. Notably, the tensile strength of the composite scaffold with 20% TTCP content reached 15.2 MPa, which was 2.9 times that of pure PCL, and the best flexural strength was found in the scaffold with 15% TTCP content (4.7 MPa). More importantly, the introduced TTCP not only achieved the effective pH regulation of the soaking solution and the promotion of biodegradation, but also provided the scaffold with good bioactivity and biocompatibility.

Composite Nanocoatings of Biomedical Magnesium Alloy Implants: Advantages, Mechanisms, and Design Strategies

The rapid degradation of magnesium (Mg) alloy implants erodes mechanical performance and interfacial bioactivity, thereby limiting their clinical utility. Surface modification is among the solutions to improve corrosion resistance and bioefficacy of Mg alloys. Novel composite coatings that incorporate nanostructures create new opportunities for their expanded use. Particle size dominance and impermeability may increase corrosion resistance and thereby prolong implant service time. Nanoparticles with specific biological effects may be released into the peri-implant microenvironment during the degradation of coatings to promote healing. Composite nanocoatings provide nanoscale surfaces to promote cell adhesion and proliferation. Nanoparticles may activate cellular signaling pathways, while those with porous or core-shell structures may carry antibacterial or immunomodulatory drugs. Composite nanocoatings may promote vascular reendothelialization and osteogenesis, attenuate inflammation, and inhibit bacterial growth, thus increasing their applicability in complex clinical microenvironments such as those of atherosclerosis and open fractures. This review combines the physicochemical properties and biological efficiency of Mg-based alloy biomedical implants to summarize the advantages of composite nanocoatings, analyzes their mechanisms of action, and proposes design and construction strategies, with the purpose of providing a reference for promoting the clinical application of Mg alloy implants and to further the design of nanocoatings.

Electrostatic Repulsive Features of Free-Standing Titanium Dioxide Nanotube-Based Membranes in Biofiltration Applications

This study presents the electrostatic repulsive features of electrochemically fabricated titanium dioxide nanotube (NT)-based membranes with different surface nanomorphologies in cross-flow biofiltration applications while maintaining a creatinine clearance above 90%. Although membranes exhibit antifouling behavior, their blood protein rejection can still be improved. Due to the electrostatically negative charge of the hexafluorotitanate moiety, the fabricated biocompatible, superhydrophilic, free-standing, and amorphous ceramic nanomembranes showed that about 20% of negatively charged 66 kDa blood albumin was rejected by the membrane with ∼100 nm pores. As the nanomorphology of the membrane was shifted from NTs to nanowires by varying fabrication parameters, pure water flux and bovine serum albumin (BSA) rejection performance were reduced, and the membrane did not lose its antifouling behavior. Herein, nanomembranes with different surface nanomorphologies were fabricated by a multi-step anodic oxidation process and characterized by scanning electron microscopy, atomic force microscopy, water contact angle analysis, X-ray diffraction, and energy-dispersive X-ray spectroscopy. The membrane performance of samples was measured in 3D printed polyethylene terephthalate glycol flow cells replicating implantable artificial kidney models to determine their blood toxin removal and protein loss features. In collected urine mimicking samples, creatinine clearances and BSA rejections were measured by the spectrophotometric Jaffe method and high-performance liquid chromatography.

Graphene oxide reinforced SrHAP composite as a drug carrier in bone regeneration

Strontium substituted HAP (SrHAP), with a 10 mol% substitution, was mineralized on increasing weight percentages of graphene oxide (2, 4 and 6). The GS composites were comprehensively characterized for drug delivery in bone reconstruction. The formation of SrHAP was verified by XRD and FT-IR results. The apatite crystallization was influenced by graphene oxide content and strontium. The EDS results confirmed the presence of strontium and HR-SEM depicted rod shape apatite, of length between 58 and 135 nm, uniformly embedded on graphene oxide. The reinforcement of graphene oxide increased the surface area, porosity, microhardness (upto 0.59 GPa), protein adsorption (upto 18.16 μg/mg), water uptake and degradation properties. Also, the increase in graphene oxide fraction significantly enhanced the curcumin encapsulation efficiency (upto 80.16%) and the drug release was considerably retarded over SrHAP. The in vitro studies using human osteoblast-like MG-63 cells demonstrated that curcumin-loaded composite was biocompatible and promoted proliferation, differentiation and matrix mineralization. The results highlight the combinational therapy of osteogenic ion (strontium) and osteogenic drug (curcumin) as a promising platform in bone tissue engineering.

Influence of Magnesium Content on the Physico-Chemical Properties of Hydroxyapatite Electrochemically Deposited on a Nanostructured Titanium Surface

The aim of this research was to obtain hydroxyapatite (HAp)-based coatings doped with different concentrations of Mg on a Ti nanostructured surface through electrochemical techniques and to evaluate the influence of Mg content on the properties of HAp. The undoped and doped HAp-based coatings were electrochemically deposited in galvanostatic pulsed mode on titania nanotubes with a diameter of ~72 nm, being designed to enhance the adhesion of the HAp coatings to the Ti substrate. The obtained materials were investigated by Scanning Electron Microscopy (SEM), Energy Dispersive Spectroscopy (EDS), X-Ray Diffraction (XRD), and Fourier-Transform Infra-Red spectroscopy (FTIR). The adhesion of the coatings to the substrate was also evaluated with the help of the “tape-test” and the micro-scratch test. The morphology (SEM) of all the coatings is made of very thin and narrow ribbon-like crystals, with some alterations with respect to the Mg amount in the coatings. Thus, a concentration of 1 mM of Mg in the electrolyte leads to wider and thicker ribbon-like crystals, while a concentration of 1.5 mM in the electrolyte generated a morphology that resembles the undoped HAp. Both phase composition (XRD) and chemical bonds (FTIR) analysis proved the formation of HAp in all coatings. Moreover, according to XRD, all coatings have a strong orientation toward the (002) plane. Irrespective of the Mg content, all coatings registered an average roughness between approx. 500 and 600 nm, while the coating thickness increased after addition of Mg, from a value of 9.6 μm, for the undoped HAp, to 11.3 μm and ~13.7 μm for H/Mg1 and H/Mg2, respectively. In terms of adhesion, it was shown that the coatings a H/Mg2 had a poorer adhesion when compared to H/Mg1 and the undoped HAp (H), which registered similar adhesion, indicating that a concentration of 1.5 mM of Mg in the electrolyte reduces the adhesion of the Hap-based coatings to the nanostructured surface. The obtained results indicated that Mg concentrations up to 1 mM in the electrolyte can enhance the properties of HAp-based coatings electrochemically deposited on a nanostructured surface, while even a slightly higher concentration of 1.5 mM can negatively impact the characteristics of HAp coatings.

Graphene oxide encapsulated forsterite scaffolds to improve mechanical properties and antibacterial behavior

It is very desirable to have good antibacterial properties and mechanical properties at the same time for bone scaffolds. Graphene oxide (GO) can increase the mechanical properties and antibacterial performance, while forsterite (Mg2SiO4) as the matrix can increase forsterite/GO scaffolds' biological activity for bone tissue engineering. Interconnected porous forsterite scaffolds were developed by space holder processes for bone tissue engineering in this research. The forsterite/GO scaffolds had a porosity of 76-78% with pore size of 300-450 μm. The mechanism of the mechanical strengthening, antibacterial activity, and cellular function of the forsterite/GO scaffold was evaluated. The findings show that the compressive strength of forsterite/1wt.% GO scaffold (2.4±0.1 MPa) was significantly increased, in comparison to forsterite scaffolds without GO (1.4±0.1 MPa). Validation of the samples' bioactivity was attained by forming a hydroxyapatite (HAp) layer on the forsterite/GO surface within in vitro immersion test. The results of cell viability demonstrated that synthesized forsterite scaffolds with low GO did not show cytotoxicity and enhanced cell proliferation. Antibacterial tests showed that the antibacterial influence of forsterite/GO scaffold was strongly correlated with GO concentration from 0.5 to 2 wt.%. The scaffold encapsulated with 2wt.% GO had the great antibacterial performance with bacterial inhibition rate around 90%. As results show, the produced forsterite/1wt.% GO can be an attractive option for bone tissue engineering.

Electrochemical Deposition of Hydroxyapatite on Stainless Steel Coated with Tantalum/Tantalum Nitride Using Simulated Body Fluid as an Electrolytic Medium

In the present work the electrochemical deposition of hydroxyapatite using simulated body fluid (SBF) as an electrolytic medium was carried out on Ta and Ta/TaN coatings on BIOLINE stainless steel SS316LVM (SS). The electrochemical deposition performed on each substrate for 3000 and 6000 s, at different potentials were determined from cyclic voltammetry. The best conditions found were −1.4 V for bare SS and −1.7 V for Ta/TaN coating. The structural characterization was carried out by SEM, FTIR, XRD, and contact angle measurements. The electrochemical characterization was done by electrochemical impedance (EIS), which allowed us to know the capacitive and resistive character of the substrates. The substrate (Ta/TaN)/SS at −1.7 V 6000 s presented the largest formation of a nonstoichiometric hydroxyapatite with a uniform distribution on the substrate, implying that Ta–OH is formed on the tantalum metallic surface, due to formation of the passivation layer of tantalum oxide. These groups attract Ca2+ ions and PO43− ions absorbed on the surface will form the precursors of the apatite crystals that finally transform to hydroxyapatite. The electrodeposition of HAp the double layer Ta/TaN resulted in a more uniform and denser layer than SS alone.

Progress in Niobium Oxide-Containing Coatings for Biomedical Applications: A Critical Review

Typically, pure niobium oxide coatings are deposited on metallic substrates, such as commercially pure Ti, Ti6Al4 V alloys, stainless steels, niobium, TiNb alloy, and Mg alloys using techniques such as sputter deposition, sol-gel deposition, anodizing, and wet plasma electrolytic oxidation. The relative advantages and limitations of these coating techniques are considered, with particular emphasis on biomedical applications. The properties of a wide range of pure and modified niobium oxide coatings are illustrated, including their thickness, morphology, microstructure, elemental composition, phase composition, surface roughness and hardness. The corrosion resistance, tribological characteristics and cell viability/proliferation of the coatings are illustrated using data from electrochemical, wear resistance and biological cell culture measurements. Critical R&D needs for the development of improved future niobium oxide coatings, in the laboratory and in practice, are highlighted.

Surface Modification of Biomedical Ti and Ti Alloys: A Review on Current Advances

Ti is widely used as a material for orthopedic implants. As rapid and effective osseointegration is a key factor for the successful application of implants, biologically inert Ti materials start to show inherent limitations, such as poor surface cell adhesion, bioactivity, and bone-growth-inducing capabilities. Surface modification can be an efficient and effective approach to addressing the biocompatibility, mechanical, and functionality issues of the various Ti implant materials. In this study, we have overviewed more than 140 papers to summarize the recent progress in the surface modification of Ti implants by physical and/or chemical modification approaches, aiming at optimizing their wear resistance, biocompatibility, and antimicrobial properties. As an advanced manufacturing technology for Ti and Ti alloys, additive manufacturing was particularly addressed in this review. We also provide an outlook for future research directions in this field as a contribution to the development of advanced Ti implants for biomedical applications.

The Early Adhesion Effects of Human Gingival Fibroblasts on Bovine Serum Albumin Loaded Hydrogenated Titanium Nanotube Surface

The soft tissue sealing at the transmucal portion of implants is vital for the long-term stability of implants. Hydrogenated titanium nanotubes (H₂-TNTs) as implant surface treatments were proved to promote the adhesion of human gingival fibroblasts (HGFs) and have broad usage as drug delivery systems. Bovine serum albumin (BSA) as the most abundant albumin in body fluid was crucial for cell adhesion and was demonstrated as a normal loading protein. As the first protein arriving on the surface of the implant, albumin plays an important role in initial adhesion of soft tissue cells, it is also a common carrier, transferring and loading different endogenous and exogenous substances, ions, drugs, and other small molecules. The aim of the present work was to investigate whether BSA-loaded H₂-TNTs could promote the early adhesion of HGFs; H₂-TNTs were obtained by hydrogenated anodized titanium dioxide nanotubes (TNTs) in thermal treatment, and BSA was loaded in the nanotubes by vacuum drying; our results showed that the superhydrophilicity of H₂-TNTs is conducive to the loading of BSA. In both hydrogenated titanium nanotubes and non-hydrogenated titanium nanotubes, a high rate of release was observed over the first hour, followed by a period of slow and sustained release; however, BSA-loading inhibits the early adhesion of human gingival fibroblasts, and H₂-TNTs has the best promoting effect on cell adhesion. With the release of BSA after 4 h, the inhibitory effect of BSA on cell adhesion was weakened.

Understanding and optimizing the antibacterial functions of anodized nano-engineered titanium implants

Nanoscale surface modification of titanium-based orthopaedic and dental implants is routinely applied to augment bioactivity, however, as is the case with other cells, bacterial adhesion is increased on nano-rough surfaces. Electrochemically anodized Ti implants with titania nanotubes (TNTs) have been proposed as an ideal implant surface with desirable bioactivity and local drug release functions to target various conditions. However, a comprehensive state of the art overview of why and how such TNTs-Ti implants acquire antibacterial functions, and an in-depth knowledge of how topography, chemistry and local elution of potent antibiotic agents influence such functions has not been reported. This review discusses and details the application of nano-engineered Ti implants modified with TNTs for maximum local antibacterial functions, deciphering the interdependence of various characteristics and the fine-tuning of different parameters to minimize cytotoxicity. An ideal implant surface should cater simultaneously to ossoeintegration (and soft-tissue integration for dental implants), immunomodulation and antibacterial functions. We also evaluate the effectiveness and challenges associated with such synergistic functions from modified TNTs-implants. Particular focus is placed on the metallic and semi-metallic modification of TNTs towards enabling bactericidal properties, which is often dose dependent. Additionally, there are concerns over the cytotoxicity of these therapies. In that light, research challenges in this domain and expectations from the next generation of customizable antibacterial TNTs implants towards clinical translation are critically evaluated. STATEMENT OF SIGNIFICANCE: One of the major causes of titanium orthopaedic/dental implant failure is bacterial colonization and infection, which results in complete implant failure and the need for revision surgery and re-implantation. Using advanced nanotechnology, controlled nanotopographies have been fabricated on Ti implants, for instance anodized nanotubes, which can accommodate and locally elute potent antibiotic agents. In this pioneering review, we shine light on the topographical, chemical and therapeutic aspects of antibacterial nanotubes towards achieving desirable tailored antibacterial efficacy without cytotoxicity concerns. This interdisciplinary review will appeal to researchers from the wider scientific community interested in biomaterials science, structure and function, and will provide an improved understanding of controlling bacterial infection around nano-engineered implants, aimed at bridging the gap between research and clinics.

Electrodeposited Hydroxyapatite-Based Biocoatings: Recent Progress and Future Challenges

Hydroxyapatite has become an important coating material for bioimplants, following the introduction of synthetic HAp in the 1950s. The HAp coatings require controlled surface roughness/porosity, adequate corrosion resistance and need to show favorable tribological behavior. The deposition rate must be sufficiently fast and the coating technique needs to be applied at different scales on substrates having a diverse structure, composition, size, and shape. A detailed overview of dry and wet coating methods is given. The benefits of electrodeposition include controlled thickness and morphology, ability to coat a wide range of component size/shape and ease of industrial processing. Pulsed current and potential techniques have provided denser and more uniform coatings on different metallic materials/implants. The mechanism of HAp electrodeposition is considered and the effect of operational variables on deposit properties is highlighted. The most recent progress in the field is critically reviewed. Developments in mineral substituted and included particle, composite HAp coatings, including those reinforced by metallic, ceramic and polymeric particles; carbon nanotubes, modified graphenes, chitosan, and heparin, are considered in detail. Technical challenges which deserve further research are identified and a forward look in the field of the electrodeposited HAp coatings is taken.

Polyvinyl Alcohol/Graphene Oxide Interlayer for Enhancing Adhesive Performance of HA Coating on C/C Composites Prepared by Hydrothermal Electrodeposition/Hydrothermal Treatment

Hydroxyapatite (HA) coatings directly deposited by hydrothermal electrochemical technology (HET) onto carbon/carbon (C/C) composites exhibited a catastrophic failure occurring at the interface of the HA and C/C. To overcome this problem, a polyvinyl alcohol (PVA)/graphene oxide (GO) interlayer (P/G interlayer) was applied on the (NH₄)₂S₂O₈-pretreated C/C substrate (named P/G-C/C) by using a dipping method. Subsequently, a calcium phosphate coating was deposited on P/G-C/C, shortened as M-P/G-C/C, by HET, and then converted into HA coating (abbreviated as HA-P/G-C/C) through posthydrothermal treatment. For comparison, HA coating was prepared onto C/C without a P/G interlayer through the same process, which was denoted as HA-C/C. The composition, microstructure, and morphology of the samples were characterized by X-ray diffractometry (XRD), energy-dispersive spectroscopy (EDS), scanning electron microscopy (SEM), Raman spectra, Fourier transform infrared (FTIR), and X-ray photoelectron spectroscopy (XPS). The adhesive performance of the coatings on C/C was measured by a scratch test. Finally, an in vitro bioactivity of the coatings was evaluated in a simulated body fluid solution at 37 °C. Results showed no apparent differences in the morphology and phase of the posttreated coatings, both of which are composed of a dense structure containing needle-like HA crystals. However, the HA-P/G-C/C sample possessed a higher Ca/P ratio and denser interface, thereby exhibiting higher adhesive performance and better bioactivity. The adhesive strength of the HA-P/G coating was observed at a critical load of 41.04 N, which increased by 29.3% relative to the HA coating. Moreover, the failure site was on the HA-P/G coating rather than at the interface. The enhanced adhesive performance was ascribed to the PVA/GO-repairing pits on C/C and PVA and GO toughening effects on the HA coating. In vitro and in vivo tests revealed no statistical significance for the two HA-coated C/C samples, although the HA-P/G coating exhibited better bioactivity, inducing the growth of bonelike apatite than the HA coating.

Electrodeposited Biocoatings, Their Properties and Fabrication Technologies: A Review

Coatings deposited under an electric field are applied for the surface modification of biomaterials. This review is aimed to characterize the state-of-art in this area with an emphasis on the advantages and disadvantages of used methods, process determinants, and properties of coatings. Over 170 articles, published mainly during the last ten years, were chosen, and reviewed as the most representative. The most recent developments of metallic, ceramic, polymer, and composite electrodeposited coatings are described focusing on their microstructure and properties. The direct cathodic electrodeposition, pulse cathodic deposition, electrophoretic deposition, plasma electrochemical oxidation in electrolytes rich in phosphates and calcium ions, electro-spark, and electro-discharge methods are characterized. The effects of electrolyte composition, potential and current, pH, and temperature are discussed. The review demonstrates that the most popular are direct and pulse cathodic electrodeposition and electrophoretic deposition. The research is mainly aimed to introduce new coatings rather than to investigate the effects of process parameters on the properties of deposits. So far tests aim to enhance bioactivity, mechanical strength and adhesion, antibacterial efficiency, and to a lesser extent the corrosion resistance.

Enhanced Human Gingival Fibroblast Response and Reduced Porphyromonas gingivalis Adhesion with Titania Nanotubes

Successful dental implants rely on stable osseointegration and soft-tissue integration. Titania nanotubes (TNTs) with a diameter of 100 nm could increase the mesenchymal stem cell response and simultaneously decrease Staphylococcus aureus adhesion. However, the interactions between the modified surface and surrounding soft tissues are still unknown. In the present study, we fully investigated the biological behavior of human gingival fibroblasts (HGFs) and the adhesion of Porphyromonas gingivalis (P. gingivalis). TNTs were synthesized on titanium (Ti) surfaces by electrochemical anodization at 10, 30, and 60 V, and the products were denoted as NT10, NT30, and NT60, respectively. NT10 (diameter: 30 nm) and NT30 (diameter: 100 nm) could enhance the HGF functions, such as cell attachment and proliferation and extracellular matrix- (ECM-) related gene expressions, with the latter showing higher enhancement. NT60 (diameter: 200 nm) clearly impaired cell adhesion and proliferation and ECM-related gene expressions. Bacterial adhesion on the TNTs decreased and reached the lowest value on NT30. Therefore, NT30 without pharmaceuticals can be used to substantially enhance the HGF response and reduce P. gingivalis adhesion to the utmost, thus demonstrating significant potential in the transgingival part of dental implants.

Effect of Ta2O5 content on the osseointegration and cytotoxicity behaviors in hydroxyapatite-Ta2O5 coatings applied by EPD on superelastic NiTi alloys

In the present study, the different contents of tantalum pentoxide (Ta₂O₅: 10, 15, 20 and 30 wt%) nanoparticles were introduced into the natural hydroxyapatite (nHA) coating structure on NiTi substrate through electrophoretic deposition (EPD) method. The phase compositions of coatings were perused before and after the sintering at 800 °C for 1 h by XRD. The incorporation of 30wt%Ta₂O₅ into nHA matrix induced the formation of undesirable soluble Ca₃(PO₄)₂ phase in composite coating. The FESEM images showed that the density of continuous nHA coating increased by compositing with Ta₂O₅. The maximum adhesion strength of 28.3 ± 0.7 MPa accomplished from the nHA-20 wt%Ta₂O₅ composite coating. The Ni ions concentration measurement results from the passivated-NiTi with nHA and nHA-(10, 15 and 20)wt%Ta₂O₅ coatings during 30 days of immersion in PBS clarified the positive role of Ta₂O₅ in decreasing the Ni leaching due to the lowering the open porosities of nHA structure. The biological response of the coating surfaces was assessed in vitro by cell culturing and MTS assay. By considering the morphology and density of adsorbed cells on each coating, the improved biocompatibility of nHA coating in the presence of Ta₂O₅ was justified by scrutinizing the surface roughness, wettability and charge. The highest cell attachment and proliferation on nHA-20 wt%Ta₂O₅ coating was related to owning the lowest roughness, wetting angle of 34^o ± 0.5 and the highest negative surface charge density. Also, the concentration of the highest negative charge density on nHA-20 wt%Ta₂O₅ coating surface in the SBF solution caused to the enhancement of the amount of the apatite nuclei through providing more sites to calcium absorption.

Properties and Mechanism of Hydroxyapatite Coating Prepared by Electrodeposition on a Braid for Biodegradable Bone Scaffolds

Hydroxyapatite (HA) coating is successfully prepared by electrodeposition on the surface of polyvinyl alcohol (PVA)/polylactic acid (PLA) braid which serves as a potential biodegradable bone scaffold. The surface morphology, element composition, crystallinity and chemical bonds of HA coatings at various deposition times (60, 75, 90, 105 and 120 min) are characterized by scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDAX), X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR), respectively. Average Surface roughness (Ra) of HA coating is observed by confocal microscopy. The results reveal that the typical characteristic peaks of the FTIR spectrum confirm that HA coating is successfully prepared on the rugged surface of the PVA/PLA braid. The XRD results indicate that the crystallinity of HA can be improved by increasing deposition time. In the 90 min-deposition, hydroxyapatite has a dense and uniform coating morphology, Ca/P ratio of 1.7, roughness of 0.725 μm, which shows the best electrodeposition performance. The formation mechanism of granular and plate-like hydroxyapatite crystals is explained by the structural characteristics of a hydroxyapatite unit cell. This study provides a foundation for a bone scaffold braided by biodegradable fibers.

Novel hydroxyapatite/graphene oxide/collagen bioactive composite coating on Ti16Nb alloys by electrodeposition

A novel implant coating material containing graphene oxide (GO) and collagen (COL), and hydroxyapatite (HA) was fabricated with the aid of tannic acid by electrodeposition. The surface of Ti16Nb alloy was subjected to anodic oxidation, and then HA-GO coating was applied to Ti16Nb surface by cathodic method. Then, COL was deposited on the surface of the HA-GO coating by the biomimetic method. HA, HA-GO, HA-GO-COL coatings on the surface of the Ti16Nb alloy have increased the corrosion resistance by the formation of a barrier layer on the surface. For HA-GO-COL coating, the highest corrosion resistance is obtained due to the compactness and homogeneity of the coating structure. The contact angle of the bare Ti16Nb is approximately 65°, while the contact angle of the coated samples is close to 0°. Herein, the increased surface wettability is important for cell adhesion. The surface roughness of the uncoated Ti16Nb alloy was between 1 and 3 μm, while the surface roughness of the coated surfaces was measured between 20 and 110 μm. The contact between the bone and the implant has been improved. Graphene oxide-containing coatings have improved the antibacterial properties compared to the GO-free coating using S. aureus. The hardness and elastic modulus of the coatings were measured by the nanoindentation test, and the addition of GO and collagen to the HA coating resulted in an increase in strength. The addition of GO to the HA coating reduced the viability of 3 T3 fibroblast cells, whereas the addition of collagen to HA-GO coat increased the cell adhesion and viability.

Development of graphene oxide/calcium phosphate coating by pulse electrodeposition on anodized titanium: Biocorrosion and mechanical behavior

In this work, graphene oxide (GO) reinforcement was used to improve the strength and fracture toughness of the calcium phosphate (CaP) coating applied on the anodized titanium using pulse electrodeposition. Based on the results, the CaP coating consisted of mixed phases of octa-calcium phosphate (OCP), dicalcium phosphate dehydrate (DCPD) and hydroxyapatite (HAp); however, compositing of this coating with GO caused deposition of the pure HAp phase. Moreover, the nanohardness and Young's modulus of the CaP-GO coating increased over 52% and 41%, respectively, as compared to those measured for the GO-free coating. An improvement of about 16% in the adhesion strength of the CaP coating composited with GO to the anodized titanium was also arisen from improving integrity, crystallinity and decreasing the Young's modulus mismatch of this coating with titanium substrate. Finally, uniformity in the microstructure and more biostability of the CaP-GO coating led to its better protection against the corrosion of anodized titanium.