Multifunctional 3D printed porous GelMA/xanthan gum based dressing with biofilm control and wound healing activity

Green Electrospun Poly(vinyl alcohol)/Gelatin-Based Nanofibrous Membrane by Incorporating 45S5 Bioglass Nanoparticles and Urea for Wound Dressing Applications: Characterization and In Vitro and In Vivo Evaluations

This study reports the fabrication and characterization of poly(vinyl alcohol) (PVA) and gelatin (Gel)-based nanofiber membranes cross-linked with citric acid (CA) by a green electrospinning method in which nano 45S5 bioglass (BG) and urea were incorporated. Various combinations of PVA, gelatin, and BG were prepared, and nanofiber membranes with average fiber diameters between 238 and 595 nm were fabricated. Morphological, chemical, and mechanical properties, porosity, swelling, water retention, and water vapor transmission rate of the fabricated membranes were evaluated. PVA:Gel (90:10), 15% CA, and 3% BG were determined as the optimum blend for nanofiber membrane fabrication via electrospinning. The membrane obtained using this blend was further functionalized with 10% w/w polymer urea coating by the electrospray method following the cross-linking. In vitro biocompatibility tests revealed that the fabricated membranes were all biocompatible except for the one that functionalized with urea. In vivo macroscopic and histopathological analysis results of PVA/Gel/BG and PVA/Gel/BG/Urea treated wounds indicated increased collagenization and vascularization and had an anti-inflammatory effect. Furthermore, careful examination of the in vivo macroscopic results of the PVA/Gel/BG/Urea membrane indicated its potential to decrease uneven scar formation. In conclusion, developed PVA/Gel/BG and PVA/Gel/BG/Urea electrospun membranes with multifunctional and biomimetic features may have the potential to be used as beneficial wound dressings.

A photocrosslinkable and hemostatic bilayer wound dressing based on gelatin methacrylate hydrogel and polyvinyl alcohol foam for skin regeneration

The enormous potential of multifunctional bilayer wound dressings in various medical interventions for wound healing has led to decades of exploration into this field of medicine. However, it is usually difficult to synthesize a single hydrogel with all the required capabilities simultaneously. This paper proposes a bilayer model with an outer layer intended for hydrogel wound treatment. By adding gelatin methacrylate (GelMA) and tannic acid (TA) to the hydrogel composition and using polyvinyl alcohol-carboxymethyl chitosan (PVA-CMCs) foam layer as supports, a photocrosslinkable hydrogel with an optimal formulation was created. The hydrogels were then examined using a range of analytical procedures, including mechanical testing, rheology, chemical characterization, and in vitro and in vivo tests. The resulting bilayer wound dressing has many desirable properties, namely uniform adhesion and quick crosslinking by UV light. When used against Gram-positive and Gram-negative bacterial strains, bilayer wound dressings demonstrated broad antibacterial efficacy. In bilayer wound dressings with GelMA and TA, better wound healing was observed. Those without these elements showed less effectiveness in healing wounds. Additionally, encouraging collagen production and reducing wound infection has a major therapeutic impact on wounds. The results of this study could have a significant impact on the development of better-performing wound dressings.

Recent advances in harnessing biological macromolecules for wound management: A review

Wound dressings (WDs) are an essential component of wound management and serve as an artificial barrier to isolate the injured site from the external environment, thereby helping to prevent exogenous infections and supporting healing. However, maintaining a moist wound environment, providing protection from infection, good biocompatibility, and allowing for gas exchange, remain a challenge in device design. Functional wound dressings (FWDs) prepared from hybrid biological macromolecule-based materials can enhance efficacy of these systems for skin wound management. This review aims to provide an overview of the state-of-the-art FWDs within the field of wound management, with a specific focus on hybrid biomaterials, techniques, and applications developed over the past five years. In addition, we highlight the incorporation of biological macromolecules in WDs, the emergence of smart WDs, and discuss the existing challenges and future prospects for the development of advanced WDs.

Pharmaceutical applications and requirements of resins for printing by digital light processing (DLP)

The digital light processing (DLP) printer has proven to be effective in biomedical and pharmaceutical applications, as its printing method does not induce shear and a strong temperature on the resin. In addition, the DLP printer has good resolution and print quality, which makes it possible to print complex structures with a customized shape, being used for various purposes ranging from jewelry application to biomedical and pharmaceutical areas. The big disadvantage of DLP is the lack of a biocompatible and non-toxic resin on the market. To overcome this limitation, an ideal resin for biomedical and pharmaceutical use is needed. The resin must have appropriate properties, so that the desired format is printed when with a determined wavelength is applied. Thus, the aim of this work is to bring the basic characteristics of the resins used by this printing method and the minimum requirements to start printing by DLP for pharmaceutical and biomedical applications. The DLP method has proven to be effective in obtaining pharmaceutical devices such as drug delivery systems. Furthermore, this technology allows the printing of devices of ideal size, shape and dosage, providing the patient with personalized treatment.

Gelatin Methacryloyl (GelMA)-Based Biomaterial Inks: Process Science for 3D/4D Printing and Current Status

Tissue engineering for injured tissue replacement and regeneration has been a subject of investigation over the last 30 years, and there has been considerable interest in using additive manufacturing to achieve these goals. Despite such efforts, many key questions remain unanswered, particularly in the area of biomaterial selection for these applications as well as quantitative understanding of the process science. The strategic utilization of biological macromolecules provides a versatile approach to meet diverse requirements in 3D printing, such as printability, buildability, and biocompatibility. These molecules play a pivotal role in both physical and chemical cross-linking processes throughout the biofabrication, contributing significantly to the overall success of the 3D printing process. Among the several bioprintable materials, gelatin methacryloyl (GelMA) has been widely utilized for diverse tissue engineering applications, with some degree of success. In this context, this review will discuss the key bioengineering approaches to identify the gelation and cross-linking strategies that are appropriate to control the rheology, printability, and buildability of biomaterial inks. This review will focus on the GelMA as the structural (scaffold) biomaterial for different tissues and as a potential carrier vehicle for the transport of living cells as well as their maintenance and viability in the physiological system. Recognizing the importance of printability toward shape fidelity and biophysical properties, a major focus in this review has been to discuss the qualitative and quantitative impact of the key factors, including microrheological, viscoelastic, gelation, shear thinning properties of biomaterial inks, and printing parameters, in particular, reference to 3D extrusion printing of GelMA-based biomaterial inks. Specifically, we emphasize the different possibilities to regulate mechanical, swelling, biodegradation, and cellular functionalities of GelMA-based bio(material) inks, by hybridization techniques, including different synthetic and natural biopolymers, inorganic nanofillers, and microcarriers. At the close, the potential possibility of the integration of experimental data sets and artificial intelligence/machine learning approaches is emphasized to predict the printability, shape fidelity, or biophysical properties of GelMA bio(material) inks for clinically relevant tissues.

Gelatin/Polyacrylamide-Based Antimicrobial and Self-Healing Hydrogel Film for Wound Healing Application

In this study, a self-healing, adhesive, and superabsorbent film made of gelatin, poly(acrylamide), and boric acid (GelAA) was successfully synthesized using a free radical reaction mechanism. The optimized film showed a remarkable 2865 ± 42% water absorptivity and also exhibited excellent self-healing behavior. The GelAA films were further loaded with silver nanoclusters (AgNCs) and ursodeoxycholic acid (UDC) (loading efficiency = 10%) to develop UDC/Ag/GelAA films. The loading of AgNCs in UDC/Ag/GelAA films helped in exhibiting 99.99 ± 0.01% antibacterial activity against both Gram-positive and Gram-negative bacteria, making them very effective against bacterial infections. Additionally, UDC/Ag/GelAA films had 77.19 ± 0.52% porosity and showed 90% of UDC release in 30 h, which helps in improving the cell proliferation. Our research provides an easy but highly effective process for synthesizing a hydrogel film, which is an intriguing choice for wound healing applications without the use of antibiotics.

Polysaccharide-based antibacterial coating technologies

To tackle antimicrobial resistance, a global threat identified by the United Nations, is a common cause of healthcare-associated infections (HAI) and is responsible for significant costs on healthcare systems, a substantial amount of research has been devoted to developing polysaccharide-based strategies that prevent bacterial attachment and biofilm formation on surfaces. Polysaccharides are essential building blocks for life and an abundant renewable resource that have attracted much attention due to their intrinsic remarkable biological potential antibacterial activities. If converted into efficient antibacterial coatings that could be applied to a broad range of surfaces and applications, polysaccharide-based coatings could have a significant potential global impact. However, the ultimate success of polysaccharide-based antibacterial materials will be determined by their potential for use in manufacturing processes that are scalable, versatile, and affordable. Therefore, in this review we focus on recent advances in polysaccharide-based antibacterial coatings from the perspective of fabrication methods. We first provide an overview of strategies for designing polysaccharide-based antimicrobial formulations and methods to assess the antibacterial properties of coatings. Recent advances on manufacturing polysaccharide-based coatings using some of the most common polysaccharides and fabrication methods are then detailed, followed by a critical comparative overview of associated challenges and opportunities for future developments. STATEMENT OF SIGNIFICANCE: Our review presents a timely perspective by being the first review in the field to focus on advances on polysaccharide-based antibacterial coatings from the perspective of fabrication methods along with an overview of strategies for designing polysaccharide-based antimicrobial formulations, methods to assess the antibacterial properties of coatings as well as a critical comparative overview of associated challenges and opportunities for future developments. Meanwhile this work is specifically targeted at an audience focused on featuring critical information and guidelines for developing polysaccharide-based coatings. Including such a complementary work in the journal could lead to further developments on polysaccharide antibacterial applications.

3D-Printed Chitosan-Based Hydrogels Loaded with Levofloxacin for Tissue Engineering Applications

Herein, we demonstrate the feasibility of a three-dimensional printed chitosan (CS)-poly(vinyl alcohol) (PVA)-gelatin (Gel) hydrogel incorporating the antimicrobial drug levofloxacin (LEV) as a potential tissue engineering scaffold. Hydrogels were prepared by physically cross-linking the polymers, and the printability of the prepared hydrogels was determined. The hydrogel with 3% w/v of CS, 3% w/v of PVA, and 2% w/v of Gel presented the best printability, producing smooth and uniform scaffolds. The integrity of 3D-printed scaffolds was improved via a neutralization process since after testing three different neutralized agents, i.e., NH3 vapors, EtOH/NaOH, and KOH solutions. It was proved that the CS/PVA/Gel hydrogel was formed by hydrogen bonds and remained amorphous in the 3D-printed structures. Drug loading studies confirmed the successful incorporation of LEV, and its in vitro release continued for 48 h. The cytotoxicity/cytocompatibility tests showed that all prepared scaffolds were cytocompatible.

Biofouling in Membrane Bioreactors-Mitigation and Current Status: a Review

Biological fouling as termed biofouling is caused by varied living organisms and is difficult to eliminate from the environment thus becoming a major issue during membrane bioreactors. Biofouling in membrane bioreactors (MBRs) is a crucial problem in increasing liquid pressure due to reduced pore diameter, clogging of the membrane pores, and alteration of the chemical composition of the water which greatly limits the growth of MBRs. Thus, membrane biofouling and/or microbial biofilms is a hot research topic to improve the market competitiveness of the MBR technology. Though several antibiofouling strategies (addition of bioflocculant or sponge into MBRs) came to light, biological approaches are sustainable and more practicable. Among the biological approaches, quorum sensing-based biofouling control (so-called quorum quenching) is an interesting and promising tool in combating biofouling issues in the MBRs. Several review articles have been published in the area of membrane biofouling and mitigation approaches. However, there is no single source of information about biofouling and/or biofilm formation in different environmental settings and respective problems, antibiofilm strategies and current status, quorum quenching, and its futurity. Thus, the objectives of the present review were to provide latest insights on mechanism of membrane biofouling, quorum sensing molecules, biofilm-associated problems in different environmental setting and antibiofilm strategies, special emphasis on quorum quenching, and its futurity in the biofilm/biofouling control. We believe that these insights greatly help in the better understanding of biofouling and aid in the development of sustainable antibiofouling strategies.

The applications of 3D printing in wound healing: the external delivery of stem cells and antibiosis

As the global number of chronic wound patients rises, the financial burden and social pressure on patients increase daily. Stem cells have emerged as promising tissue engineering seed cells due to their enriched sources, multidirectional differentiation ability, and high proliferation rate. However, delivering them in vitro for the treatment of skin injury is still challenging. In addition, bacteria from the wound site and the environment can significantly impact wound healing. In the last decade, 3D bioprinting has dramatically enriched cell delivery systems. The produced scaffolds by this technique can be precisely localized within cells and perform antibacterial actions. In this review, we summarized the 3D bioprinting-based external delivery of stem cells and their antibiosis to improve wound healing.

Combinational System of Lipid-Based Nanocarriers and Biodegradable Polymers for Wound Healing: An Updated Review

Skin wounds have imposed serious socioeconomic burdens on healthcare providers and patients. There are just more than 25,000 burn injury-related deaths reported each year. Conventional treatments do not often allow the re-establishment of the function of affected regions and structures, resulting in dehydration and wound infections. Many nanocarriers, such as lipid-based systems or biobased and biodegradable polymers and their associated platforms, are favorable in wound healing due to their ability to promote cell adhesion and migration, thus improving wound healing and reducing scarring. Hence, many researchers have focused on developing new wound dressings based on such compounds with desirable effects. However, when applied in wound healing, some problems occur, such as the high cost of public health, novel treatments emphasizing reduced healthcare costs, and increasing quality of treatment outcomes. The integrated hybrid systems of lipid-based nanocarriers (LNCs) and polymer-based systems can be promising as the solution for the above problems in the wound healing process. Furthermore, novel drug delivery systems showed more effective release of therapeutic agents, suitable mimicking of the physiological environment, and improvement in the function of the single system. This review highlights recent advances in lipid-based systems and the role of lipid-based carriers and biodegradable polymers in wound healing.

3D Printing as a Technological Strategy for the Personalized Treatment of Wound Healing

Wound healing is a dynamic process which involves stages of hemostasis, inflammation, proliferation and remodeling. Any error in this process results in abnormal wound healing, generating financial burdens for health systems and even affecting the physical and mental health of the patient. Traditional dressings do not meet the complexities of ideal treatment in all types of wounds. For this reason, in the last decades, different materials for drug delivery and for the treatment of wounds have been proposed reaching novel level of standards, such as 3D printing techniques. The use of natural or synthetic polymers, and the correct design of these printed products loaded with cells and/or combined with active compounds, can generate an effective system for the treatment of wounds, improving the healing process and generating customized dressings according to the patient needs. This manuscript provides a comprehensive review of different types of 3D printing techniques, as well as its use in wound healing and its different stages, including the advantages and limitations of additive manufacturing and future perspectives.

3D Printing Technologies in Personalized Medicine, Nanomedicines, and Biopharmaceuticals

3D printing technologies enable medicine customization adapted to patients' needs. There are several 3D printing techniques available, but majority of dosage forms and medical devices are printed using nozzle-based extrusion, laser-writing systems, and powder binder jetting. 3D printing has been demonstrated for a broad range of applications in development and targeting solid, semi-solid, and locally applied or implanted medicines. 3D-printed solid dosage forms allow the combination of one or more drugs within the same solid dosage form to improve patient compliance, facilitate deglutition, tailor the release profile, or fabricate new medicines for which no dosage form is available. Sustained-release 3D-printed implants, stents, and medical devices have been used mainly for joint replacement therapies, medical prostheses, and cardiovascular applications. Locally applied medicines, such as wound dressing, microneedles, and medicated contact lenses, have also been manufactured using 3D printing techniques. The challenge is to select the 3D printing technique most suitable for each application and the type of pharmaceutical ink that should be developed that possesses the required physicochemical and biological performance. The integration of biopharmaceuticals and nanotechnology-based drugs along with 3D printing ("nanoprinting") brings printed personalized nanomedicines within the most innovative perspectives for the coming years. Continuous manufacturing through the use of 3D-printed microfluidic chips facilitates their translation into clinical practice.

The 3D printed conductive grooved topography hydrogel combined with electrical stimulation for synergistically enhancing wound healing of dermal fibroblast cells

Patients with extensive cutaneous damage resulting from poor wound healing often have other comorbidities such as diabetes that may lead to impaired skin functions and scar formation. Many recent studies have shown that the application of electrical stimulation (ES) to cutaneous lesions significantly improves skin regeneration via activation of AKT intracellular signaling cascades and secretion of regeneration-related growth factors. In this study, we fabricated varying concentrations of gelatin-methacrylate (GelMa) hydrogels with poly(3,4-ethylenedioxythiophene) (PEDOT): polystyrene sulfonate (PSS), which is a conductive material commonly used in tissue engineering due to its efficiency among conductive thermo-elastic materials. The results showed successful modification of PEDOT:PSS with GelMa while retaining the original structural characteristics of the GelMa hydrogels. In addition, the incorporation of PEDOT:PSS increased the interactions between both the materials, thus leading to enhanced mechanical strength, improved swelling ratio, and decreased hydrophilicity of the scaffolds. Our GelMa/PEDOT:PSS scaffolds were designed to have micro-grooves on the surfaces of the scaffolds for the purpose of directional guiding. In addition, our scaffolds were shown to have excellent electrical conductivity, thus leading to enhanced cellular proliferation and directional migration and orientation of human dermal fibroblasts. In vivo studies revealed that the GelMa/PEDOT:PSS scaffolds with electrical stimulation were able to induce full skin thickness regeneration, as seen from the various stainings. These results indicate the potential of GelMa/PEDOT:PSS as an electro-conductive biomaterial for future skin regeneration applications.

Mechanically Tough and Regenerable Antibacterial Nanofibrillated Cellulose-Based Aerogels for Oil/Water Separation

Nanofibrillated cellulose (NFC)-based aerogels have been widely used for various applications. However, the disadvantages of poor structural stability, low mechanical toughness, and easy contamination by bacteria hinder their large-scale application. In this work, 3-(3'-acrylicacidpropylester)-5,5-dimethyl hydantoin (APDMH) was grafted on oxidized NFC (ONC) to prepare antibacterial poly(APDMH)-g-ONC (PAC). PAC and poly(ethyleneimine) (PEI) were chemically cross-linked using 3-glycidoxypropyltrimethox (GPTMS), aiming at constructing a PAC-g-PEI aerogel with multiple network structures. The mechanical behaviors of composite aerogel and oil/water separation performances under different conditions were investigated. PAC-g-PEI aerogel exhibits outstanding fatigue resistance (>50 cycles of compression) and superior elasticity (96.76% height recovery after five compression-release cycles at 50% strain). The obtained superhydrophilic and underwater-oleophobic properties endow the aerogel with excellent oil/water separation performances, achieving a satisfactory separation efficiency of over 99% and flux of over 9500 L·m^-2·h^-1. Furthermore, the chlorinated aerogel of PAC-g-PEI-Cl shows highly efficient and rechargeable antibacterial properties, can inactivate 6.72-log Escherichia coli and 6.60-log Staphylococcus aureus within 10 min, and can still kill all inoculated bacteria after 50 cycles. In addition, PAC-g-PEI-Cl aerogel can inhibit biofilm formation, making it a promising candidate for highly efficient oil/water separation applications in diverse harsh conditions.

Multifunctional hydrogels for wound dressings using xanthan gum and polyacrylamide

Developing advanced dressings that integrate multiple functions is one of the major challenges in current clinical wound treatment. In this study, Xanthan gum (XG) and polyacrylamide (PAAm) materials were used to prepare hydrogel dressings by one-pot method. With the combination of the PAAm network and the XG network, the PAAm-XG hydrogels showed the tensile strength of 0.36 MPa and the stretchability as large as 2078 %. The prepared PAAm-XG hydrogels had excellent water uptake efficiency with the swelling ratio of 1200 %. Besides, the developed dressings possessed outstanding biocompatibility, universal adhesion and self-healing ability. More importantly, the PAAm-XG hydrogels can be successfully loaded with Cefixime and human recombinant epidermal growth factor, and these loaded hydrogels released these bioactive molecules in sustained ways. As a result, both E. coli and S. aureus bacteria were inactivated after contacting with the Cefixime-loaded hydrogels for 24 h. Furthermore, in vivo data demonstrated that the PAAm-XG hydrogel dressings significantly accelerated the wound healing in a mouse model. All of these indicate that the multifunctional PAAm-XG hydrogels are promising candidates for wound treatment.

Controlled and Sequential Delivery of Stromal Derived Factor-1 α (SDF-1α) and Magnesium Ions from Bifunctional Hydrogel for Bone Regeneration

Bone healing is a complex process that requires the participation of cells and bioactive factors. Stromal derived factor-1 α (SDF-1α) and magnesium ions (Mg²⁺) both are significant bioactive factors for cell recruitment and osteogenesis during bone regeneration. Thus, a bifunctional hydrogel containing a sequential delivery system is fabricated to improve osteogenesis. During sequential delivery of the hydrogel, SDF-1α is predominantly released at the early stage of bone mesenchymal stem cells (BMSCs) recruitment, while Mg²⁺ are constantly delivered at a later stage to improve osteogenic differentiation of recruited cells. In addition, due to the early release of SDF-1α, the hydrogel showed strong BMSCs recruitment and proliferation activity. Mg²⁺ can not only induce up-regulation of osteogenic gene expression in vitro, but also promote bone tissue and angiogenesis in vivo. Taken together, the injection of xanthan gum-polydopamine crosslinked hydrogel co-loading SDF-1α and Mg²⁺ (XPMS hydrogel) provides a novel strategy to repair bone defects.

Investigation of 3D-printed chitosan-xanthan gum patches

In this study, using a new polymer combination of Chitosan(CH)/Xanthan Gum(XG) has been exhibited for wound dressing implementation by the 3D-Printing method, which was fabricated due to its biocompatible, biodegradable, improved mechanical strength, low degradation rate, and hydrophilic nature to develop cell-mimicking, cell adhesion, proliferation, and differentiation. Different concentrations of XG were added to the CH solution as 0.25, 0.50, 0.75, 1, and 2 wt% respectively in the formic acid/distilled water (1.5:8.5) solution and rheologically characterized to evaluate their printability. The results demonstrated that high mechanical strength, hydrophilic properties, and slow degradation rate were observed with the presence and increment of XG concentration within the 3D-Printed patches. Moreover, in vitro cell culture research was conducted by seeding NIH 3T3 fibroblast cells on the patches, proving the cell proliferation rate, viability, and adhesion. Finally, 1% XG and 4% CH containing 3D-Printed patches were great potential for wound dressing applications.

The 3D Bioprinted Scaffolds for Wound Healing

Skin tissue engineering and regeneration aim at repairing defective skin injuries and progress in wound healing. Until now, even though several developments are made in this field, it is still challenging to face the complexity of the tissue with current methods of fabrication. In this review, short, state-of-the-art on developments made in skin tissue engineering using 3D bioprinting as a new tool are described. The current bioprinting methods and a summary of bioink formulations, parameters, and properties are discussed. Finally, a representative number of examples and advances made in the field together with limitations and future needs are provided.