Coracoid bone block fixation with cortical buttons: An alternative to screw fixation?

Non-screw glenoid augmentation constructs for shoulder instability with bone loss: A biomechanical assessment of static and elastic cerclage constructs

Purpose

This study aims to compare the biomechanical performance of elastic and static suture-based cerclage systems to traditional screw constructs in the setting of modeled glenoid bony augmentation.

Methods

Biomechanical testing was conducted on polyurethane cellular foam blocks modeling a 20 % glenoid defect repaired with a coracoid graft. Constructs consisted of an elastic suture-based cerclage, static suture-based cerclage, and a two-screw construct. Biomechanical testing was performed on material testing system, using a 7-phase, 100 cycle per phase, 1Hz, sinusoidal cyclic loading protocol, following a stair-step pattern in load control. Failure for cyclic loading was assessed at 0.8 mm linear displacement. The absolute end level for load-to-failure was 7.0 mm.

Results

Static suture-based cerclage failed at 5-50 N (Cycles 2 through 4), 2-screw constructs failed at 25-50 N (Cycle 4), and elastic suture-based cerclage failed at 100-200N (Cycles 6 and 7). Elastic cerclage exhibited superior performance compared to static cerclage beginning in Cycle 2 (p = 0.0440) and compared to SOC 2-screw construct beginning in Cycle 4 (p = 0.0118). 2-screw construct exhibited superior stability performance compared to static cerclage beginning in Cycle 3 (p = 0.0001). Elastic cerclage reached failure at 558.141 ± 4.508 N, while 2-screw construct and static cerclage reached failure at 422.009 ± 24.998 N and 366.770 ± 66.653 N, respectively. Elastic cerclage demonstrated superior biomechanical stability in load-at-failure performance to static cerclage (p < 0.0001) and the screw construct (p < 0.0001), while static cerclage demonstrated inferior biomechanical stability to the screw construct (p = 0.0343).

Conclusion

This biomechanical study comparing the performance of elastic cable and static suture tape cerclage fixation methods identified that the elastic cable cerclage exhibits a higher load-at-failure and less displacement under repetitive stress. In addition, elastic cable cerclage fixation exhibits greater strength and construct rigidity than traditional metal screw fixation.

Latarjet procedure: open with screws or arthroscopic with cortical buttons? A retrospective cohort comparison of outcomes and complications

BACKGROUND

The original Latarjet-Patte procedure is a reliable technique to treat traumatic anterior shoulder instability. However, attempts to reduce possible complications have led to the emergence of modified techniques. More prominent among them are the arthroscopic approach and the use of cortical buttons for coracoid fixation. To date, limited research is available directly comparing the simultaneous use of these 2 modifications to the original Latarjet-Patte technique. The purpose of this article is to compare clinical and radiologic outcomes and complications between open Latarjet with screws and arthroscopic Latarjet with cortical buttons for traumatic anterior shoulder instability.

METHODS

A multicenter retrospective cohort study was performed of medical records and imaging studies of 2 groups of patients, with 2 years of follow-up, who underwent either one of 2 variations of the Latarjet procedure: open approach with screws (open-screw group) or arthroscopic approach with cortical buttons (scope-button group). Group homogenization was ensured by statistical comparison of 14 baseline independent variables as well as multiple regression analysis to assess confounding factors. The primary outcome was the Rowe score at 24 months after surgery, for which the minimal clinically important difference of 9.7 points was used. Secondary outcomes were recurrence of instability, graft positioning, the Rowe score at other points in time, and complications.

RESULTS

Thirty-eight patients were evaluated in the open-screw group and 44 in the scope-button group, with a 24-month follow-up. All but 1 patient in each group achieved the minimal clinically important difference from pre- to postoperative Rowe score. The Rowe score did not differ between groups during any of the assessment times. There was no difference regarding graft vertical (P = .620) or horizontal (P = .280) positioning. There was 1 recurrence in each group: a dislocation in the open-screw group (P = .463) and a subluxation in the scope-button group (P > .999). Other complications happened exclusively in the scope-button group: neuropraxia (n = 1; P > .999), infection (n = 2; P > .999), graft fracture (n = 1; P > .999), and graft migration (n = 2; P > .999). Multiple regression analysis did not observe influence from any of the potential confounding factors on the final results.

CONCLUSION

At early follow-up, arthroscopic Latarjet with cortical buttons yielded comparably good clinical and radiologic results to the conventional open Latarjet with screws.

Evaluating a simple modified button approach in acromio-clavicular joint injury: Case report

INTRODUCTION AND IMPORTANCE

Shoulder stability is crucial, and appropriate therapy is essential for improving patient outcomes following an injury.

CASE PRESENTATION

A 30-year-old male was admitted to the clinic after lifting heavy objects at the fitness center. The physical examination reveals a decreased range of motion (ROM) and impaired flexion and external rotation of the shoulder joint. The left shoulder X-ray shows moderate soft tissue swelling without discontinuities of the bone, although elevation of the distal clavicle is prominent. After a comprehensive examination, the patient was diagnosed with an acromioclavicular (AC) joint injury.

CLINICAL DISCUSSION

We use a mini-open surgical method called a Simple Modified Button Technique (SMB) to maintain shoulder function. The Visual Analog Scale (VAS) and Oxford Shoulder Score (OSS) were measured to evaluate the patient's outcome.

CONCLUSION

The SMB procedure could adequately treat AC joint injuries. Measurement tools such as VAS and OSS have shown promising results. Adequate treatment will appropriately manage prolonged pain in AC joint injuries.

Bone formation of the coracoid bone graft after the Bristow procedure assessed using three-dimensional computed tomography

BACKGROUND

The Bristow procedure has been shown to be a reliable method to prevent recurrent anterior shoulder instability by compensating for glenoid bone loss and producing the sling effect. The degree of postoperative morphological change in the coracoid bone graft is speculated to influence glenohumeral joint stability; however, the details of these changes after the Bristow procedure remain unknown. This study was performed to quantify the postoperative change in the coracoid bone graft volume as assessed by three-dimensional computed tomography (3D-CT).

METHODS

The Bristow procedure was performed on 17 shoulders in 17 patients from August 2018 to January 2020. All patients were men, and their mean age at surgery was 17.9 years. The mean follow-up duration was 21.4 months. Within the first week after the operation (Time 0) and at the final follow-up, 3D-CT was used to determine the total coracoid bone graft volume. The clinical outcomes were evaluated using the Japanese Orthopaedic Association (JOA) shoulder score, the University of California Los Angeles (UCLA) shoulder score, and the Western Ontario Shoulder Instability Index (WOSI).

RESULTS

The mean volume of the total coracoid bone graft was 1.26 ± 0.29 cm3 at Time 0 and 1.90 ± 0.36 cm3 at the final follow-up (p < 0.0001). The mean JOA score, UCLA score, and WOSI were significantly better at the final follow-up than preoperatively (p < 0.001). No postoperative infection, neurovascular injury, or recurrent instability of the glenohumeral joint occurred.

CONCLUSIONS

In the Bristow procedure, the volume of the total coracoid bone graft as shown by 3D-CT was significantly greater at the final follow-up than at Time 0, and bone formation of the coracoid bone graft was found after the Bristow procedure.

Improvement of coracoid process union rates: a comparative study of conventional open and arthroscopic-assisted Bristow procedures for treating anterior shoulder instability in rugby players

BACKGROUND

The Bristow coracoid transfer procedure is a reliable technique for treating anterior shoulder instability in patients with large glenoid bone loss or those involved in collision sports. However, its success is marred by its inferior bone union rate of the coracoid process as compared to the Latarjet procedure. This study aimed to evaluate whether arthroscopic confirmation of the secured coracoid fixation during the Bristow procedure improves the bone union rate and clinical outcomes as compared to the open procedure.

METHODS

We retrospectively reviewed 104 rugby players (n = 111 shoulders) who underwent an open (n = 66 shoulders) or arthroscopy (AS)-assisted (n = 45 shoulders) Bristow procedure at our center from 2007 to April 2019. In the AS-assisted group, the screw fixation and coracoid stability and contact were confirmed under arthroscopic visualization. Graft union was evaluated through computed tomography at 3 months, 6 months, and 1 year postoperatively. Patient-reported outcome measures were assessed based on the American Shoulder and Elbow Surgeons score, Rowe score, and satisfaction rate. Recurrence, the rate of return to play (RTP), and the frequency of pain after RTP were also assessed.

RESULTS

The mean follow-up period was 73.5 (range: 45-160) months for the open group and 32.3 (range: 24-56) months for the AS-assisted group. In the former, the rates of bone union were 50%, 72.7%, and 88.9% at 3 months, 6 months, and 1 year, respectively. In contrast, the AS-assisted group had significantly greater bone union rates-88.9%, 93.3%, and 95.6% at 3 months, 6 months, and 1 year, respectively. Both groups showed significant improvement in the American Shoulder and Elbow Surgeons and Rowe scores compared to preoperative values as well as high satisfaction rates (open: 92%; AS-assisted: 95.7%). There were no statistically significant differences in the recurrence and RTP rates as well as the frequency of pain after RTP between the 2 groups.

CONCLUSION

The AS-assisted procedure allows early and high bone healing without compromising the clinical outcomes.

Promising clinical effect of arthroscopic autologous iliac bone grafting with suture anchor binding fixation for recurrent anterior shoulder instability

Background

To evaluate the clinical efficacy of arthroscopic autologous iliac bone grafting with suture anchor binding fixation combined with a Bankart repair for recurrent anterior shoulder dislocation with a significant anterior glenoid defect.

Methods

Patients with recurrent anterior shoulder dislocation with an anterior glenoid defect area greater than 20% admitted to our department from March 2019 to March 2022 were prospectively enrolled. Arthroscopic autologous iliac bone grafting with suture anchor binding fixation combined with a Bankart repair was performed. Computed tomography (CT) images were captured preoperatively, immediately after surgery, and at 3, 6, and 12 months postoperatively to evaluate the glenoid defect area, graft area, and graft healing. Shoulder function was assessed using the Instability Severity Index, Oxford Shoulder Instability, and Rowe scores recorded preoperatively and at the final follow-up. The shoulder range of motion, shoulder stability test, surgery-related complications, subluxation/dislocation, and revision surgery were also evaluated.

Results

A total of 32 patients were included in the study, with an average follow-up time of 18.3 ± 6.3 months, when the graft healing rate was shown to be 100%. The area ratio of the graft to the glenoid was 37.6% ± 10.5% (range, 23.5%-44.1%) determined by an enface-view three-dimensional CT performed immediately after surgery, and 29.2 ± 8.2% (range, 19.6%-38.7%) at 12 months postoperatively. At the final follow-up, the glenoid defect had improved from 28.7 ± 6.4% (range, 20.5%-40.6%) before surgery to -10.2 ± 4.7% (range, -13.8% to 6.1%). The preoperative Rowe and Oxford scores were 56.4 ± 8.5 and 34.7 ± 7.1 respectively, which improved to 94.3 ± 6.7 and 15.3 ± 3.2 at the final follow-up (p < .001). All patients had no limited shoulder joint activity, no re-dislocation or revision surgery, and no neurovascular injury.

Conclusions

For recurrent anterior shoulder dislocation with an anterior glenoid defect area greater than 20%, arthroscopic autologous iliac bone grafting with suture anchor fixation combined with a Bankart repair produced a promising clinical effect. A significant shoulder function score was achieved, as was a 100% bone healing rate and ideal glenoid reconstruction without major complications. Thus, this technique may be considered an alternative to the classic Latarjet approach to treat recurrent anterior shoulder dislocation with an anterior glenoid defect area greater than 20%.

Level of Evidence

IV.

Association of the Inlay Structure Used in the Modified Bristow Procedure With Accelerated Bone Union: Comparing the Cuistow and Modified Bristow Procedures

Background

The Chinese unique inlay Bristow (Cuistow) procedure is a modified Bristow surgery in which an inlay (mortise-and-tenon) structure is added to the contact surface between the coracoid tip and the glenoid. Patients who have undergone the Cuistow procedure have had satisfying clinical performance and excellent postoperative bone healing rates (96.1%).

Purpose

To compare the clinical and radiographic outcomes after the arthroscopic Cuistow procedure and the arthroscopic Bristow procedure.

Study Design

Cohort study; Level of evidence, 3.

Methods

A total of 91 patients who underwent either the Cuistow or Bristow procedure between January 2017 and March 2018 were selected, and 69 patients (70 shoulders; 35 in the Cuistow group and 35 in the Bristow group) were included. Clinical assessment at minimum 24 months postoperatively, including the visual analog scale for pain and instability, American Shoulder and Elbow Surgeons score, Rowe score, subjective shoulder value score, and active range of motion, was completed by independent observers and compared with values collected preoperatively. Assessment with 3-dimensional computed tomography scans was performed preoperatively; immediately after the operation; at 3, 6, and 12 months postoperatively; and at the final follow-up.

Results

A total of 69 patients (70 shoulders) were included, with a mean follow-up duration of 34.41 ± 5.99 months (range, 24-50 months). Both groups saw significant improvement in visual analog scale for pain and instability, American Shoulder and Elbow Surgeons, Rowe, and subjective shoulder value scores at the final follow-up compared with the preoperative values (P < .001 for all), with no significant between-group differences on any clinical outcomes at the final follow-up. The 3-month postoperative graft union rate on computed tomography was significantly higher in the Cuistow group compared with the Bristow group (82.9% vs 51.4%, respectively, P = .003), although the graft union rate at the final follow-up was not significantly different (94.3% vs 85.7%, respectively; P = .449).

Conclusion

Patients receiving the Cuistow procedure had equivalent clinical outcomes and a significantly higher bone union rate at 3 months postoperatively than those in the Bristow group. The inlay structure used in the Cuistow procedure was found to be associated with accelerated bone union.

The Arthroscopically Guided Bristow-Latarjet Procedure With Cortical Button Fixation: A Minimum 10-Year Follow-up

BACKGROUND

Despite improved visualization, the use of arthroscopic surgery to perform the Latarjet procedure has not decreased the rates of complications and glenohumeral osteoarthritis (OA) in the long term. Many of the reported complications are related to the use of screws for bone block fixation with freehand drilling.

PURPOSE

To evaluate the long-term (at a minimum 10-year follow-up) clinical and radiological outcomes of the arthroscopic Bristow-Latarjet procedure using a posterior guided drilling technique and suture button for coracoid bone graft fixation.

STUDY DESIGN

Case series; Level of evidence, 4.

METHODS

Consecutive patients who underwent the arthroscopic Bristow-Latarjet procedure with suture button fixation between 2011 and 2013 were reviewed by 2 independent evaluators. Complications and revision surgery were recorded, and we evaluated patient-reported outcomes including subjective scores, recurrence of shoulder instability (dislocation or subluxation), range of motion limitations, and return to sports. Patients had radiographs taken at least 10 years after surgery to assess glenohumeral OA according to the Samilson-Prieto classification system and computed tomography scans to assess bone block positioning and healing.

RESULTS

A total of 65 consecutive patients (68 shoulders) with a mean follow-up of 135 months (range, 120-156 months) were included. The mean age at the time of surgery was 25 ± 8 years; 7 patients had previous failed Bankart repair. At follow-up, 94% (64/68) of the shoulders had no recurrence of instability. The 4 cases of instability recurrence were traumatic and occurred at 3 weeks (a fall), 4 months, 2 years, and 7 years after surgery. No hardware failures, coracoid fractures, or neurological complications were observed. Overall, 61 patients (94%) were still participating in sports, with 44 (68%) at the same or higher level. Range of motion showed nonsignificant restrictions in external rotation with the arm at the side (7° ± 9°) and with the arm at 90° of abduction (9° ± 10°) compared with the contralateral side. Additionally, 11 shoulders (16%) had some residual anterior apprehension on clinical examination. At last follow-up, 77% (47/61) of the shoulders had no OA development or progression. Previous failed Bankart repair was a risk factor for the development of OA. Patients with OA had significantly lower Subjective Shoulder Value scores (79% vs 91%, respectively; P = .01) and decreased external rotation with the arm at the side (40° vs 65°, respectively; P = .001) compared with patients with no or little OA.

CONCLUSION

The arthroscopically guided Bristow-Latarjet procedure with suture button fixation is a safe and durable surgical treatment method for recurrent anterior shoulder instability, allowing a high rate of return to sports without significant motion restrictions and no or little OA in the long term.

Does the use of a tensioning device improve stability for suture fixation of glenoid bone constructs? A biomechanical analysis

Purpose

The purpose of this study is to quantify the difference in biomechanical stability of suture button (SB) and suture tape cerclage (STC) constructs with hand tensioning versus device tensioning of anterior glenoid augmentation bone grafts in an anterior glenoid bone loss model.

Methods

Artificial bone blocks with a density of 15 lb/ft3 (240.3 kg/m3) were used as models for glenoid fixation with bone graft. The biomechanical stability of SB and STC tensioned by hand was compared to those tensioned by a device. Average displacement (mm) following application of various forces (50, 100, 150, and 200 N) during a 7-phase, 100-cycle, stairstep cyclic loading protocol was recorded.

Results

Both SB and STC fixation displayed significantly lower construct displacement at all tested forces when tensioned with a device versus hand (p < 0.001). Device-tensioned SB and STC were comparable in construct stability at forces below 100N. However, at forces above 100 N, device-tensioned SB exhibited significantly less displacement than device-tensioned STC.

Discussion

Using a tensioning device for SB or STC fixation of a coracoid graft model results in less displacement and improved stability compared to hand tensioning. Biomechanically, a tensioning device enhances the stability of suture fixation in glenoid bone graft constructs.

Suture Button Congruent Arc Latarjet Procedure in the Treatment of Recurrent Anterior Shoulder Instability With Glenoid Bone Loss Greater Than 25

It is generally believed that glenoid bone loss (GBL) greater than 25% can be defined as a massive GBL. For this type of recurrent anterior shoulder instability, the traditional Latarjet technique is usually inadequate to restore the GBL. Although the congruent arc Latarjet technique is able to reconstruct a wider glenoid defect with good clinical outcomes, this technique had not been widely applied due to the limited bone width of the coracoid graft and high rate of coracoid osteotomy and screw fixation-related complications. The emerging suture button flexible fixation technique has been proven to achieve good clinical outcomes and is technically friendly. It can significantly reduce the requirements for large coracoid graft bone mass, and the Latarjet procedure's application scope is expanded. We introduce the suture button congruent arc Latarjet technique for treatment of massive GBL in this Technical Note.

Sutures, Screws, Buttons, and Anchors: A Review of Current Bone Graft Fixation Devices for Glenoid Bone Loss in the Unstable Shoulder

PURPOSE OF REVIEW

Anterior shoulder instability is associated with concomitant injury to several stabilizing structures of the shoulder, including glenoid bone loss. While instability is most common in young athletes and patients with predisposing conditions of hyperlaxity, recurrent shoulder instability can occur throughout various age ranges and may lead to longer term effects including pain and shoulder arthritis. Glenoid bone loss exceeding certain thresholds is generally treated by glenoid reconstruction via bone block augmentation to adequately stabilize the glenohumeral joint. These procedures increase the width of the articular surface on which the humeral head can translate before dislocation and, based on the procedure performed, provide a sling effect via the conjoined tendon, and increase tension to support the anterior capsule. The purpose of this review is to summarize the available literature regarding bone block fixation techniques.

RECENT DEVELOPMENTS

Various fixation techniques have been utilized to secure bone block transfers. Though screw fixation has traditionally been used for bone block fixation, suture buttons, suture anchors, and all-suture techniques have been utilized in attempts to avoid complications associated with the use of screws. Biomechanical studies report variable force-resistance, displacement, and mode of failure when comparing screw to suture button-based fixation of glenoid bone blocks. Clinical and radiographic studies have shown these novel suture-based techniques to be comparable, and in some cases advantageous, to traditional screw fixation techniques. While screw fixation has long been the standard of care in glenoid bone block procedures, it is associated with high complication rates, leading surgeons to endeavor toward new fixation techniques. In available biomechanical studies, screw fixation has consistently demonstrated high maximal load-to-failure and displacement with cyclic loading. Studies have reported similar clinical and radiographic outcomes in both screw and suture-based fixation methods, with evidence of reduced bone resorption with suture fixation. While suture button fixation is associated with a higher rate of recurrent instability, overall complication rates are low. Future research should address biomechanical shortcomings of suture-based fixation techniques and continue to assess long-term follow-up of patients treated with each fixation method.

Screw Fixation for the Latarjet Procedure May Reduce Risk of Recurrent Instability but Increases Reoperation Rate Compared to Suture-Button Fixation: A Systematic Review

PURPOSE

To perform a systematic review to compare clinical outcomes, complications, and reoperation rates of patients undergoing the Latarjet procedure with screw vs suture-button fixation.

METHODS

A systematic review was performed by searching PubMed, the Cochrane Library, and Embase to identify clinical studies directly comparing screw vs suture-button fixation for the Latarjet procedure. The search terms used were shoulder screw suture button. Patients were evaluated based on reoperation rate, complication rate, recurrent instability, radiologic outcomes, and patient-reported outcomes. Graft and screw position were assessed via computed tomography.

RESULTS

Seven studies (1 Level II, 6 Level III) met inclusion criteria, with 845 patients undergoing the Latarjet procedure with screw fixation (screw group) and 279 patients with suture-button fixation (suture-button group). Mean patient age ranged from 21.2 to 29.6 years. Mean follow-up time ranged from 6.0 to 40.8 months. The recurrent instability rate ranged from 0% to 2.5% in the screw group and 0% to 8.3% in the suture-button group. The reoperation rate ranged from 0% to 7.7% in the screw group compared to 0% to 1.9% in the suture-button group. One study reported significantly lower visual analog scale pain scores in the suture-button group compared with the screw group (1.5 vs 1.2, P = .003). No other studies reported significant differences in any patient-reported outcomes. There was no significant difference in horizontal or vertical graft position, graft union rate, or complication rate between groups in any study.

CONCLUSIONS

The Latarjet procedure with screw fixation may result in a lower risk of recurrent instability compared to suture-button fixation, although screw fixation may also have a higher reoperation rate due to hardware-related complications.

LEVEL OF EVIDENCE

Level III, systematic review of Level II to III studies.

Suture Button Fixation in Latarjet Has Similar Load to Failure and Clinical Outcomes but Lower Bone Resorption Compared With Screw Fixation: A Systematic Review

PURPOSE

To compare the 2 Latarjet fixation techniques-screw fixation (SF) versus suture button (SB) -for clinical, biomechanical, and radiologic outcomes.

METHODS

A systematic review was conducted in accordance with Preferred Reporting Items for Systematic and Meta-Analyses guidelines using MEDLINE and Embase databases and was prospectively registered on PROSPERO. Only comparative clinical and biomechanical studies of Latarjet with SF and SB were included. Studies were appraised using the Methodical Index for Non-Randomised Studies (MINORS) tool.

RESULTS

Eleven studies met eligible criteria: 7 clinical studies (SB, n = 279; SF, n = 845) and 4 biomechanical. In total, 80.9% (SB) and 84.2% (SF) of patients were male. Follow-up ranged from 6 to 63.6 months. The overall recurrent instability rate for SB ranged from 0 to 8.3% and for SF ranged from 0 to 2.75%. Only one study demonstrated a greater recurrent instability rate with SB (P = .02). Overall SB complication rates ranged from 0 to 12.5% and SF ranged from 0 to 27%. Two studies reported greater complications and reoperations with SF related to hardware. Summary forest plots from 4 studies showed no significant difference in Walch Duplay score (mean difference, range -5.00 to 1.20 [95% confidence interval {CI} -12.13 to 8.56], I2 inconsistency = 0%), Rowe score (mean difference, range -2.00 to 4.00 [95% CI -7.37 to 7.66], I2 inconsistency = 45%), and VAS for pain (mean difference, range -0.10 to 0.60 [95% CI -0.72 to 1.33], I2 inconsistency = 0%). There was no statistically significant difference between SB and SF in the postoperative range of motion. Radiologically, there was no significant difference in graft positioning and union at final follow-up, but graft resorption was greater in SF (range 25.2%-47.6%) compared with SB (range 10.1%-18.5%). Biomechanical studies showed no significant difference in maximum load to failure (SB, range 184-266 N vs SF, range 148-288 N).

CONCLUSIONS

Clinically, SB fixation demonstrated similar functional outcome and range of motion when compared with SF, with the potential benefit of lower rates of graft resorption and hardware-related complications. Biomechanically there was no difference in maximum load to failure.

LEVEL OF EVIDENCE

Level III, systematic review of Level III and biomechanical studies.

Current Trends and Outcomes for Open vs. Arthroscopic Latarjet

PURPOSE OF REVIEW

This paper aims to analyze and compare the existing research on open and arthroscopic Latarjet procedures for treating anterior shoulder instability. The review will assess different factors such as graft positioning, functional outcomes, complications, and return-to-play rates for both approaches. The study's primary goal is to establish which technique yields superior outcomes.

RECENT FINDINGS

Recent studies have suggested that arthroscopic Latarjet surgery can produce outcomes similar to open surgery regarding functional scores and patient satisfaction. Some research indicates that arthroscopy may even provide slightly better results. Both techniques have similar complication rates, but arthroscopy requires a longer learning curve and operating time. It is crucial to ensure the proper placement of the graft, and some studies suggest that arthroscopy may be better at achieving accurate positioning. Both open and arthroscopic Latarjet procedures are equally effective in treating shoulder instability. While arthroscopy offers a faster recovery time and causes less soft tissue damage, it requires surgeons to undergo a steeper learning curve. The optimal graft position for both techniques is still debated. More long-term data is needed to establish superiority. Future research should compare approaches in larger cohorts and identify outcome-affecting factors to improve the treatment of shoulder instability. Both techniques are promising, but arthroscopy may be a better option as the procedure evolves into a less invasive reconstruction.

Editorial Commentary: Suture Button Fixation for the Latarjet Procedure Is Superior to Screw Fixation

An increasing body of evidence suggests that suture button fixation is comparable with screw fixation in Latarjet and potentially associated with reduced graft resorption. Suture button fixation may facilitate performing the Latarjet procedure, particularly when done in an arthroscopic manner. The use of suture button fixation technique theoretically facilitates improved positioning of the graft on the glenoid, as it frees the surgeon from the potential of the soft-tissue envelope to impact positioning of the graft, which can occur with screw-based guides. The bone graft can be shuttled into an optimal position and then tensioned with relative ease in comparison with screw-based techniques. Suture button fixation results in lower complication rates compared with screw fixation; almost one third of the screw fixation complications are hardware-related, and screw fixation results in a high rate of hardware removal. Moreover, the arthroscopic Latarjet suture button literature is published by experienced surgeons. Arthroscopic Latarjet has a significant learning curve, reducing the translatability of studies that report superior findings with any one technique. The generalizability of results reminds us that evidence-based medicine should be practiced through the lens of not only patient preferences, but also through an honest appraisal of a surgeon's own ability.

Faster strength recovery and better strength ratio with arthroscopic Latarjet compared to the open technique: An observational study

INTRODUCTION

The arthroscopic bone block has shown reliability and reproducibility regarding functional scores and shoulder mobility compared to the open bone block technique. The recovery of muscle strength, especially the strength ratio external rotator/internal rotator (ER/IR), is crucial to recovering satisfactory function. This ratio should be as near to 1 as possible, meaning a good strength balance. Little is known about the difference in strength recovery between the open and arthroscopic techniques.

HYPOTHESIS

Arthroscopic Latarjet reduces surgical stress and improves the strength recovery and strength ratio.

OBJECTIVES

To compare arthroscopic and open Latarjet procedures for shoulder muscle strength and functional outcomes.

MATERIAL AND METHODS

It was an observational longitudinal and prospective cohort follow-up. Two groups of patients were accessible for comparison: 35 in an arthroscopy group and 38 in an open group. The main outcome was the muscle strength of shoulder muscles measured with a dynamometer and expressed in Newton (N) at day 21 (D21), D45, D90, D180, and D365 in the operated and contralateral shoulders. The measurements were made for the pectoralis major, the three deltoid fascicles, and the subscapularis. The shoulder ER/IR strength ratio was calculated. Other variables were the range of motion (ROM), the Walch-Duplay (WD), the Western Ontario Shoulder Instability score (WOSI), and the Visual Analogic Scale for pain assessment. The strength, ROM, and functional scores were compared between open and arthroscopy with linear mixed models.

RESULTS

The median strengths at 52 weeks were significantly higher than at 3 weeks (P<10-4): anterior deltoid (AD) 8N (Q1:7, Q3: 9) versus 4N (Q1:2, Q3: 5), lateral deltoid (LD) 9N (Q1:9, Q3: 11) versus 6N (Q1:4, Q3: 7), posterior deltoid (PD) 14N (Q1:12, Q3: 15) versus 9N (Q1:8, Q3: 10), subscapularis 10N (Q1:9, Q3: 12) versus 7N (Q1:5, Q3: 8), and pectoralis major (PM) 11N (Q1:9, Q3: 12) versus 7N (Q1:5, Q3: 10). The overall strengths were lower in the open group compared to the arthroscopy group: AD -2.1N (CI95%[-3.1--1.2], p=0.0005), LD -1.3N (CI95% [-2.4--0.15], p=0.03), PD -0.35N (CI95% [-1-0.9], p=0.52), subscapularis -2.1N (CI95% [-3.3--0.7], p=0.006), and PM -1.4N (CI95% [-2.2--0.02], p=0.03). The ER/IR ratio was stable throughout the follow-up for both the operated and contralateral shoulders (p>0.5). The overall mean ratio was 1.3 (median 1.2, Q1: 1, Q3:1.45) for the operated shoulder and 1.1 (median 1, Q1: 0.9, Q3:1.3) for the contralateral shoulder (p=0.0004). The average ER/IR ratio was 0.27 points higher in the open group (CI95% [0.1-0.46], p=0.003). The ROM was similar between the two groups, and there was no correlation between the ER/IR ratio and the ROM (p>0.5). The VAS < 3 weeks and WD > 12 weeks were significantly poorer in the open group: +0.61 (CI95% [0.03-1.16] p=0.02), and -7.3 points (CI95% [-13--0.01], p=0.05), on average, respectively.

CONCLUSION

The patients in the arthroscopy group had a better ER/IR strength ratio (closer to 1) and better WOSI after 12 weeks. The strength and the ROM were not correlated with each other.

LEVEL OF EVIDENCE

III.

Comparison of Return to Sports and Competition After the Arthroscopic Bristow-Latarjet Procedure Versus Arthroscopic Bankart Repair in Adolescents With Recurrent Anterior Shoulder Instability

BACKGROUND

The use of isolated soft tissue repair versus bone block stabilization for the treatment of recurrent anterior shoulder instability in adolescents has no scientific evidence.

PURPOSE

To compare the clinical outcomes of adolescent patients who underwent isolated arthroscopic Bankart (iB) repair with those who underwent the arthroscopic Bristow-Latarjet procedure in addition to Bankart (BLB) repair.

STUDY DESIGN

Cohort study; Level of evidence, 3.

METHODS

A total of 60 shoulders in adolescents (aged 13-18 years) were reviewed with a minimum 2 years' follow-up: iB repair (n = 36) and arthroscopic Bankart repair with an additional Bristow-Latarjet procedure (BLB; n = 24). The characteristics of the patients in each group in terms of age at the first instability episode, age at surgery, hyperlaxity, participation in at-risk sports, and Instability Severity Index Score were comparable. The mean follow-up was longer in the iB group (7.7 vs 4.1 years, respectively), whereas the rates of patients engaged in competition and those with glenoid lesions were higher in the BLB group. The primary outcome measures were failure, defined as the recurrence of instability (clinical dislocation or subluxation), and return to sports. The mean follow-up was 6.2 years (range, 2-16 years).

RESULTS

At the last follow-up, the rate of recurrence was significantly higher in the iB group, with 22% (8/36) failures, than in the BLB group, with 8% (2/24) instability recurrences (P < .05). The rate of return to sports at the same level was significantly higher after the BLB repair than after iB repair (79% vs 47%, respectively; P < .001). No statistical difference was found in patient-reported outcome scores between treatment groups (P > .05). Although failures occurred early after the BLB repair, 88% of failures after iB repair occurred after 2 years. On multivariate analysis, adolescents in the iB group with >3 episodes of preoperative dislocation and shoulder hyperlaxity (external rotation >90°) had a 60% recurrence rate (P < .005).

CONCLUSION

Adolescent patients undergoing the BLB repair had a lower rate of recurrent instability and higher rates of return to sports and competition than those undergoing iB repair. Patients with shoulder hyperlaxity (external rotation >90°) and >3 dislocations had an unacceptable failure rate of 60% after iB repair.

Primary bone graft stability after Latarjet surgery: biomechanical evaluation of a fixation technique with metal-free all-suture cerclage vs. cortical screws

BACKGROUND

To reduce hardware-related complications in coracoid graft fixation to the anterior aspect of the glenoid, a metal-free Latarjet technique was recently introduced. The aim of this study was to compare the primary stability of a classic Latarjet procedure with 2 metal screws to a novel metal-free, all-suture cerclage method. It is hypothesized that fixation of the coracoid graft with 2 malleolar screws will provide higher primary stability compared with an all-suture cerclage technique.

METHODS

This biomechanical in vitro study was conducted on 12 fresh-frozen cadaveric shoulders (6 matched pairs) with a mean donor age of 80 years (range, 67-89 years). Coracoid graft fixation was performed using a recently introduced all-suture cerclage technique (group A) or a classic Latarjet technique with two 4.5-mm malleolar screws (group B). The conjoint tendon was loaded with a static force of 10 N to simulate the sling effect. Graft loading with a probe head consisted of 6 ascending load levels (10-50 N, 10-100 N, 10-150 N, 10-200 N, 10-250 N, and 10-300 N) with 100 cycles each at 1 Hz. Relative motion of the bone graft to the glenoid was measured using an optic 3-dimensional system.

RESULTS

While loading the conjoint tendon with 10 N, no difference in mean displacement of the bone-graft was found between both groups (P = .144). During cyclic loading, a significant difference in relative displacement for both groups was already detected in load level 1 (group A: 2398.8 μm vs. group B: 125.7 μm; P = .024), and this trend continued with the following load levels (P < .05).

DISCUSSION AND CONCLUSION

The study demonstrated that the innovative metal-free, all-suture cerclage fixation technique results in higher micromotion than the classic coracoid graft fixation with 2 malleolar screws. According to the present biomechanical investigation, shoulders treated with a metal-free all-suture cerclage technique might need adapted rehabilitation protocols to protect the construct and allow for graft healing.

Suspensory fixation for bone transfer procedures in shoulder instability is superior to screws in an angled construct: a biomechanical analysis

Background

The Latarjet procedure is a common bony augmentation procedure for anterior shoulder instability. Historically, screw fixation is used to secure the coracoid graft to the anterior glenoid surface; however, malpositioning of the graft leads to oblique screw insertion that contributes to complications. Suture buttons (SBs) are a more recent fixation technique that have not been studied alongside standard screw fixation in the context of biomechanical models of angulated fixation. This study aims to compare the biomechanical strength of single and double, screw and SB fixation at various levels of angulation.

Methods

Testing was performed using polyurethane models from Sawbones. The graft piece was secured with screw fixation (Arthrex, Naples, FL, USA) or suspensory button (ABS Tightrope, Arthrex, Naples, FL, USA). Single or double constructs of screws and SBs were affixed at 0°, 15°, and 30° angles to the face of the glenoid component. An aluminum testing jig held the samples securely while a materials testing system applied loads. Five constructs were used for each condition and assessed load to failure testing.

Results

For single fixation constructs, suspensory buttons were 60% stronger than screws at 0° (P < .001), and 52% stronger at 15° (P = .004); however, at 30°, both were comparable (P = .180). Interestingly, single suspensory button at 15° was equivalent to a single screw at 0° (P = .310). For double fixation, suspensory buttons (DT) were 32% stronger than screws at 0° (P < .001) and 35% stronger than screws at 15° (P < .001). Both double fixation methods were comparable at 30° (P = .061). Suspensory buttons at 15° and 30° were equivalent to double screws at 0 (P = .280) and 15° (P = .772), respectively.

Conclusion

These measurements indicate that the suspensory button has a significantly higher load to failure capacity over the screw fixation technique, perpendicularly and with up to 15° of angulation. These analyses also indicate that the suspensory button fixation offers superior strength even when positioned more obliquely than the screw fixation. Therefore, suspensory button fixation may confer more strength while offering greater margin for error when positioning the graft.

Isolated Primary Latarjet Procedures for Anterior Shoulder Instability Results in High Rates of Graft Resorption and Glenohumeral Degenerative Changes With Low Rates of Failure at a Minimum 2-Year Follow-Up: A Systematic Review

PURPOSE

To evaluate the incidence of postoperative complications after an isolated primary Latarjet procedure for anterior shoulder instability at a minimum 2-year follow-up.

METHODS

A systematic review was performed in accordance with 2020 PRISMA guidelines. EMBASE, Scopus, and PubMed databases were queried from database inception through September 2022. The literature search was limited to human clinical studies reporting on postoperative complications and adverse events after a primary Latarjet procedure with a minimum 2-year follow-up. Risk of bias was measured using the Newcastle-Ottawa Scale.

RESULTS

Twenty-two studies, consisting of 1,797 patients (n = 1,816 shoulders), with a mean age of 24 years were identified. The overall postoperative complication rate ranged from 0% to 25.7%, with the most common complication being persistent shoulder pain (range: 0%-25.7%). Radiological changes included graft resorption (range: 7.5%-100%) and glenohumeral degenerative changes (range: 0%-52.5%). Recurrent instability following surgery was documented in 0% to 35% of shoulders, while the incidence of bone block fractures ranged from 0% to 6% of cases. Postoperative nonunion, infection, and hematomas had a reported incidence rate ranging from 0% to 16.7%, 0% to 2.6%, and 0% to 4.4%, respectively. Overall, 0% to 7.5% of surgeries were reported failures, and 0% to 11.1% of shoulders required reoperation, with a revision rate ranging from 0% to 7.7%.

CONCLUSIONS

The incidence of complications following the primary Latarjet procedure for shoulder instability was variable, ranging from 0% to 25.7%. High rates of graft resorption, degenerative changes, and nonunion were present while failure and revision rates remained low at a minimum 2-year follow-up.

LEVEL OF EVIDENCE

Level III, systematic review of Level I-III studies.

The Arthroscopic Bristow Procedure Is Superior to the Arthroscopic Latarjet Procedure in Return to Sports but Inferior in Graft Healing: A Comparative Study With 3.4-Year Follow-Up

PURPOSE

To compare clinical and computed tomography outcomes between the arthroscopic Latarjet procedure and the arthroscopic Bristow procedure.

METHODS

Patients who underwent arthroscopic Latarjet or Bristow procedures with at least 2 years of follow-up were retrospectively reviewed. Thirty-eight shoulders were included in the Latarjet group, and 34 were included in the Bristow group. Recurrence of dislocation, clinical scores, rate of return to sports (RTS), and computed tomography assessment findings (position of transferred coracoid, graft healing, graft absorption, and glenohumeral degenerative osteoarthritis [OA]) were obtained at final follow-up.

RESULTS

No recurrent dislocation occurred in either group, and no significant differences in clinical scores were found between the 2 procedures, with a mean follow-up period of 3.4 years. The operative time in the Bristow group was significantly shorter than that in the Latarjet group (P < .001). The transferred coracoid had healed in 94.7% of the patients in the Latarjet group and 85.3% in the Bristow group at final follow-up (P = .01). No significant difference in graft absorption or the degree of glenohumeral OA was detected between the 2 groups. However, moderate to severe OA only occurred in the Latarjet group at final follow-up (4 of 38 shoulders, 10.5%). The postoperative external rotation angle and level of RTS favored the Latarjet procedure (P = .030 and P = .034, respectively).

CONCLUSIONS

Both the arthroscopic Latarjet and arthroscopic Bristow procedures led to good clinical scores with no new dislocation episodes. The Bristow group showed significantly less graft healing than the Latarjet group. However, the arthroscopic Bristow procedure took less operative time and showed a lower rate of early moderate to severe glenohumeral OA, better range of motion, and a higher rate of RTS.

LEVEL OF EVIDENCE

Level III, retrospective comparative therapeutic trial.

A Systematic Review of Screw and Suture Button Glenoid Augmentation Constructs

Background

Glenohumeral dislocations often lead to glenoid bone loss and recurrent instability, warranting bony augmentation. While numerous biomechanical studies have investigated fixation methods to secure a graft to the glenoid, a review of available constructs has yet to be performed.

Purpose

To synthesize the literature and compare the biomechanics of screw and suture button constructs for anterior glenoid bony augmentation.

Study Design

Systematic review.

Methods

A systematic review was conducted in accordance with the PRISMA (Preferred Reporting Items for Systematic Reviews and Meta-Analyses) guidelines. There were 2 independent reviewers who performed a literature search using the PubMed, Embase, and Google Scholar databases of studies published between 1950 and 2020. Studies were included that compared the biomechanical outcomes of fixation for the treatment of anterior shoulder instability with glenoid bone loss.

Results

Overall, 13 of the 363 studies screened met the inclusion criteria. The included studies measured the biomechanical strength of screws or suture buttons on a cadaveric or synthetic Latarjet construct. Screws and suture buttons were biomechanically similar, as both constructs exhibited comparable loads at failure and final displacement. Screw type (diameter, threading, or composition) did not significantly affect construct strength, and double-screw fixation was superior to single-screw fixation. Additionally, 2 screws augmented with a small plate had a higher load at failure than screws that were not augmented. Unicortical double-screw fixation was inferior to bicortical double-screw fixation, although construct strength did not significantly decrease if 1 of these screws was unicortical. Further, 2 screws inserted at 15° off axis experienced significantly higher graft displacement and lower ultimate failure loads than those inserted at 0° parallel to the glenoid.

Conclusion

Suture buttons provided comparable strength to screws and offer an effective alternative to reduce screw-related complications. Augmentation with a small plate may clinically enhance construct strength and decrease complications through the dispersion of force loads over a greater surface area. Differences in screw type did not appear to alter construct strength, provided that screws were placed parallel to the articular surface and were bicortical.

Bristow-Latarjet Surgery: A Current Overview in Brazil

Objective  To provide a current overview of the Bristow-Latarjet surgery in Brazil. Materials and Methods  This cross-sectional study was based on an electronic questionnaire with 26 items, which was sent to active members of the Brazilian Society of Shoulder and Elbow Surgery (Sociedade Brasileira de Cirurgia do Ombro e Cotovelo, SBCOC, in Portuguese). The questionnaire addressed training, surgical technique, complications, and postoperative management. Results  We sent the questionnaire to 845 specialists from April 20 to May 12, 2021, and 310 of them answered i in full. During their specialization, most specialists participated in up to ten Bristow-Latarjet procedures. The most frequent complication was graft fracture, while the most common technical difficulty was screw positioning. In total, 50.6% and 73.9% reported having experienced intraoperative and postoperative complications respectively; 57.1% declared performing subscapularis suture; 99.7% indicated postoperative immobilization; and 61.9% considered graft consolidation fundamental. Conclusion  Most specialists participated in up to ten Bristow-Latarjet procedures during the specialization, but 13.5% of them graduated without participating in the surgery. The most frequent complication was graft fracture. The most common technical difficulty was screw positioning. Most participants prefer postoperative immobilization since they believe graft consolidation is essential to resume the practiced of sports. The highest complication rate occurred with specialists who have obtained their titles 11 to 15 years ago. In Brazil, the Southeast region is the largest producer of specialists and has the highest concentration of these professionals.

Recurrent Anterior Shoulder Instability Treated Using the Arthroscopic Bankart-Latarjet Technique: Experience of a Peripheral Hospital

The arthroscopic Bankart-Latarjet procedure is used in the surgical management of anterior shoulder instability. This technique is mainly performed in referral centers due to its high technicity. This study aimed to evaluate surgical outcomes in a peripheral hospital center. This is a retrospective study of patients treated for recurrent anterior shoulder instability. The clinical scores (Walch-Duplay, Rowe, and Western Ontario Shoulder Instability Index (WOSI)) were assessed preoperatively and at 12 months after surgery. The consolidation and the position of the bone block were evaluated at 6 months using a CT scan. Between 2016 and 2020, 40 patients had been operated on (mean age: 28.5 ± 7.9 years). During a mean follow-up of 29.5 ± 11.6 months, we noted only one complication, a case of fracture of the callus of a consolidated bone block. No recurrence of instability was recorded. The Walch-Duplay score increased from 17.8 to 94.6, the Rowe score from 24.9 to 96.8, and the WOSI score decreased from 52.1% to 6.9%. The bone block was consolidated in 35 patients (87.5%), and a flush position with the anterior edge of the glenoid was noted for all patients. At one year, 67.0% of the patients practicing sport had returned to sports. The arthroscopic Bankart-Latarjet technique was a reliable procedure in the hands of an experienced shoulder surgeon, even in a peripheral hospital center.

Arthroscopic Remnant Coracoid Autograft for Revision of the Failed Latarjet Procedure With Persistent Glenoid Bone Loss

Recurrence of anterior instability after a Latarjet procedure with persistent glenoid bone loss can be related to coracoid bone block resorption, migration, or malposition. Multiple options are available to address anterior glenoid bone loss, including autograft bone transfers (such as iliac crest graft, distal clavicle autograft) or allografts (distal tibia allograft). Here, we present the use of the remnant coracoid process as an option for consideration in the treatment of glenoid bone loss after failed Latarjet procedure with persistent glenoid bone loss. The remnant coracoid autograft is harvested and transferred inside the glenohumeral joint, through the rotator interval, and fixed using cortical buttons. This arthroscopic procedure includes using 1) glenoid and coracoid drilling guides to optimize graft positioning and making the procedure more reproducible and safer and 2) a suture tensioning device to provide intraoperative graft compression and ensure bone graft healing.

Arthroscopic Distal Clavicle Bone Block Technique for Anteroinferior Instability With Critical Bone Loss

Arthroscopic distal clavicle autograft represents a locally available source of autograft for bone block augmentation in patients with anterior shoulder instability with glenoid bone loss. Anatomic and biomechanical studies have supported distal clavicle autograft use as comparable to coracoid graft with regard to restoration of glenoid articular surface, with the theoretical advantage of minimizing complications associated with coracoid transfer procedures, such as neurologic injury and coracoid fracture. The current technique describes a modification of those previously described, including a mini-open approach for distal clavicle autograft harvest, orientation of the distal clavicle with the medial clavicle graft against the glenoid (congruent arc), an all-arthroscopic technique of graft passage, and graft placement and fixation using specialized drill guides and four suture buttons to reproducibly place and secure the graft with final capsulolabral advancement over the graft to render it extra-articular.

Open Versus Arthroscopic Latarjet for Recurrent Anterior Shoulder Instability: A Systematic Review and Meta-analysis

Background

The open Latarjet (OL) procedure and arthroscopic Latarjet (AL) procedure are able to treat recurrent anterior shoulder instability (RASI) with high success rates.

Purpose

To evaluate the clinical efficacy and postoperative revisions and complications between the OL and AL procedures in the treatment of RASI.

Study Design

Systematic review; Level of evidence, 3.

Methods

MEDLINE, Embase, and the Cochrane Library were searched to retrieve and include cohort studies comparing the OL and AL procedures for RASI. Clinical outcomes were compared, and results were reported as odds ratios (ORs) or mean differences (MDs) with 95% CIs.

Results

Eleven clinical trials with 1217 patients were included. There were no differences between the procedures in pain score, Rowe score, Walch-Duplay score, external rotation, persistent apprehension, instability, recurrence, revisions attributed to recurrent instability, overall complications, wound infection, hematoma, graft complications, screw-related complications, or osteoarthritis. When compared with the OL procedure, the AL procedure had a significantly lower nonunion rate (OR, 9.92; 95% CI, 1.71 to 57.71; P = .01); however, the AL procedure had a longer operation time (MD, -24.49; 95% CI, -48.44 to -0.54; P = .05), lower Western Ontario Shoulder Instability Index score (MD, 97.27; 95% CI, 21.91 to 172.63; P = .01), higher revision rate (OR, 0.39; 95% CI, 0.16 to 0.95; P = .04), and greater screw deviation (MD, -6.41; 95% CI, -10.25 to -2.57; P = .001).

Conclusion

For most outcome measures, no difference was seen between the OL and AL procedures. The AL procedure had a lower Western Ontario Shoulder Instability Index score and a higher revision rate and appeared to have a significant learning curve. However, the AL procedure resulted in a lower nonunion rate.

The Arthroscopic Trillat Procedure Is a Valuable and Durable Treatment Option for Recurrent Anterior Instability Associated With Massive Irreparable Cuff Tears

PURPOSE

The purpose of the present study is to report the mid- and long-term clinical and radiologic outcomes of the arthroscopic Trillat for the treatment of recurrent anterior instability in patients with chronic massive irreparable rotator cuff tears (MIRCTs) and maintained active shoulder motion where reverse shoulder arthroplasty (RSA) is not indicated.

METHODS

Twenty-one consecutive patients (mean age 61 years) were identified and retrospectively reviewed. All patients had recurrent anterior dislocations and conserved active forward elevation and active external rotation. The MIRCTs included a retracted (stage 3) supraspinatus tear in 14%, a supra- and infraspinatus tear in 76.5%, and a 3-tendon tear in 14%. A closed-wedge osteotomy of the coracoid was performed, and the coracoid was fixed above the subscapularis with a cannulated screw (10 cases) or suture buttons (11 cases). We followed patients with x-rays and computed tomography scan at 6 months, along with Subjective Shoulder Value, visual analog scale, Walch, Constant, and Rowe scores. The mean clinical and radiographic follow-up was 58 months (24-145 months).

RESULTS

Overall, 96% (20/21) of the patients had a stable and functional shoulder and were satisfied with the procedure; no patient lost active shoulder motion. The Subjective Shoulder Value increased from 44% (10%-75%) to 94% (80%-100%), P < .001. The Constant and Rowe scores improved from 60 (25-81) to 81 (66-96) and from 54 (35 to 65) to 92 (70-100), respectively (P < .001). Among the 13 patients practicing sports before surgery, 10 (77%) went back to sports. At last follow-up, only 1 patient was revised to RSA.

CONCLUSIONS

The arthroscopic Trillat procedure is a valuable and durable option for the treatment of recurrent anterior dislocations in older patients with chronic MIRCTs and conserved active shoulder motion.

LEVEL OF EVIDENCE

Level IV, therapeutic case series.

Open Latarjet with Metal-Free Cerclage Fixation

Despite multiple modifications, the Latarjet is still the most popular procedure for recurrent anterior shoulder instability with glenoid bone loss. Partial or subtotal resorption of the graft is common, potentially leading to hardware prominence and risk of anterior soft-tissue impingement. To minimize the technical difficulties and morbidity associated with metallic implants, a coracoid and conjoint tendon transfer with a mini-open approach using Cerclage tape suture is described, as an alternative for the Latarjet procedure typically performed with metal screws and plates.

Arthroscopic double-button Latarjet osteolysis and remodeling at 1-year follow-up

HYPOTHESIS

The aim of this study was to evaluate the osteolysis rate, graft remodeling, and risk factors for osteolysis at the 1-year threshold after an arthroscopic Latarjet procedure with double-button fixation.

METHOD

In this multicenter, retrospective study, postoperative computed tomography scans obtained after an arthroscopic Latarjet procedure with double-button fixation to treat anterior shoulder instability were analyzed at 15 days and at 3, 6, and 12 months. Graft volume, dimensions, and morphologic remodeling were analyzed.

RESULTS

Twenty-seven patients were included (mean age, 26 years). At 1 year, osteolysis occurred in 19 of 27 patients (70%). The volume initially decreased until 6 months' follow-up (-35%; range, -75% to +26%) and then increased until our last follow-up. At 1 year, the graft volume decreased by 17% (range, -61% to +56%) compared with the immediate postoperative volume. In multivariate analysis, the rate of osteolysis was inversely associated with an unhealed graft at 3 months (P = .02; β coefficient = -44.50 [95% confidence interval, -81 to -8]). The maximal height of the graft significantly grew 0.2 cm (range, -55 to +124 mm) (P = .015). In the sagittal plane, osteolysis occurred in the superior part in 100% of patients (27 of 27) whereas bone formation occurred in the inferior part. In the axial plane, osteolysis occurred in the anterior part whereas bone formation occurred in the posterior part. In the articular part, the observed remodeling was aimed to obtain a new anatomic and congruent glenoid.

CONCLUSIONS

At 1 year after an arthroscopic Latarjet procedure with double-button fixation, osteolysis occurred in 70% of patients. The rate of osteolysis was 17% of the initial volume. Osteolysis occurred mainly during the first 6 months, in the anterior and superior parts. Remodeling led to a circular anatomic glenoid. This osteolysis did not cause any recurrence of instability or require revision surgery.

Use of Cannulated Screws for Primary Latarjet Procedures

Background

Rapid consolidation of the bone block is paramount for the success of the Latarjet procedure. Noncannulated screws have shown satisfactory long-term bone block fusion, while cannulated screws are challenged with inferior mechanical properties and fusion rates.

Purpose

To report outcomes of the Latarjet procedure using cannulated screws, notably bone block fusion and complication rates at 3 months, as well as clinical scores and return to sports at minimum 2 years postoperatively.

Study Design

Case series; Level of evidence, 4.

Methods

We reviewed the records of 124 consecutive patients (124 shoulders) who underwent primary Latarjet procedures using cannulated screws between 2015 and 2018. All patients underwent clinical examination at 3 months postoperatively, including range of motion and radiographs to assess graft fusion. The Walch-Duplay score, Rowe score, Subjective Shoulder Value, and visual analog scale for pain were collected at a minimum follow-up of 2 years.

Results

Overall, 9 patients (7%) required reoperation: 7 (6%) had screw removal for unexplained residual pain, 1 (0.8%) had lavage for deep infection, and 1 (0.8%) had evacuation to treat a hematoma. Furthermore, 3 patients (2.4%) had recurrent instability, none of whom underwent reoperation. At 3-month follow-up, all 124 shoulders showed complete radiographic graft fusion, and at 40 ± 11 months (mean ± SD; range, 24-64 months), 88% of patients had returned to sport (109/124), the Walch-Duplay score was 86 ± 14, Rowe was 84 ± 15, Subjective Shoulder Value was 88 ± 11, and visual analog scale for pain was 1 ± 1.

Conclusion

The clinical relevance of these findings is that 4.5-mm cannulated screws are safe and effective for primary Latarjet procedures and grant adequate graft healing, with low recurrence of instability and a high rate of return to sports.

Tensioning device increases coracoid bone block healing rates in arthroscopic Latarjet procedure with suture-button fixation

BACKGROUND

There is growing interest in using suture buttons for coracoid fixation to avoid the complications associated with screws during the Latarjet procedure. However, achieving bone block healing is critical for successful shoulder stabilization and return to sport. The purpose of this study was to assess and compare the healing rates and positioning of the coracoid bone block fixed with cortical suture buttons that were either manually tensioned (using a knot pusher) or mechanically tensioned (using a tensioning device) during arthroscopic Latarjet procedures.

METHODS

This prospective, nonrandomized, comparative study enrolled 69 consecutive patients (mean age, 27 years) who underwent an arthroscopic guided Latarjet procedure with suture-button fixation. Hand tensioning was performed in the first 34 shoulders, whereas the next 35 shoulders underwent mechanical tensioning. Twelve patients (17%) had a history of failed Bankart stabilization. The characteristics of the patients in each group in terms of age, sex, type of sport, bone loss, number of previous failed surgical procedures, smoking, and length of follow-up were comparable. Intraoperatively, the tensioning device was set at 100 N successively 3 times until complete immobilization of the bone block was confirmed, as assessed with a probe. The primary outcome measure was coracoid bone block union and position on computed tomography scan images at 6 months' follow-up. Secondary outcome measures included functional outcome scores, shoulder stability, return to sports, and complications at last follow-up.

RESULTS

Overall, the rate of bone block healing was 74% (25 of 34 patients) in the hand-tensioning group and 94% (33 of 35 patients) in the mechanical tensioning group (P = .043). Smoking was an independent risk factor associated with nonunion (P < .001) in each group. Patient age, size of the preoperative glenoid bone defect (<20% or >20%), and a history of surgery were not found to have any influence. The tensioning modality did not affect the bone block position, which was subequatorial in 92% of the cases and flush with the glenoid rim in 92%. At a mean of 34 months of follow-up (range, 24-62 months), 96% of the patients (65 of 69) had a stable shoulder and 87% returned to sports. At final follow-up, no significant difference in clinical scores was noted between the groups; no neurologic or hardware complications were observed.

CONCLUSION

Mechanical tensioning achieves significantly higher healing rates than hand tensioning during the arthroscopic Latarjet procedure with suture-button fixation. The use of a suture-tensioning device is a key step to the suture-button fixation technique during arthroscopic Latarjet procedures. By making the suture-button construct rigid, the tensioning device transforms the initially flexible suture into a "rigid fixation", similar to a bolt (or a rivet).

LUtarjet-limit unique coracoid osteotomy Latarjet (With video)

Background

The Latarjet procedure is an effective technique for the treatment of recurrent anterior shoulder dislocation with glenoid bone loss. However, the inevitable destruction of the coracoacromial arch may result in humeral head translation. The aim of the study is to introduce a modified Latarjet technique with coracoacromial arch preservation as well as its short term clinical outcomes.

Methods

We propose a novel individualized flexible arthroscopic suture button fixation Latarjet technique called `LUtarjet' with video. Precise measurements of the coracoid process, glenoid deficiency and osteotomy plane were made preoperatively. Only three arthroscopic portals were needed and limit unique coracoid osteotomy was performed with coracoacromial arch preservation. The mini window splitting of the subscapularis was performed from the posterior to the anterior direction and the split window was as small as 8–10 mm in length.

Results

A total of 27 patients (25.6 ± 5.4 years) were included in the study. The average surgical duration was 55.6 ± 6.3 min and the mean follow-up time was 8.1 ± 1.5 months. The functional score was significantly improved at the last follow-up. Radiologic evidence showed that the bone graft healing was placed in the desired position. No complications were found.

Conclusions

We present a fast, easy, accurate, safe arthroscopic ‘LUtarjet’ technique called FEAST that can simplify the arthroscopic Latarjet process and achieve a satisfactory bone graft position and satisfactory short-term clinical outcomes.

Level of evidence

IV, case series.

Open Bristow Versus Open Latarjet for Anterior Shoulder Instability in Rugby Players: Radiological and Clinical Outcomes

Background:

Coracoid transfer is a reliable method for managing anterior shoulder instability in athletes who play contact sports; however, differences between the Bristow and Latarjet procedures are unclear.

Purpose:

To compare clinical outcomes and rates of bone union and bone resorption of the coracoid process between the open Bristow and open Latarjet procedures in rugby players.

Study Design:

Cohort study; Level of evidence, 3.

Methods:

Rugby players who underwent an open Bristow or an open Latarjet procedure were retrospectively reviewed for anterior shoulder instability, and 66 shoulders in the Bristow group and 35 in the Latarjet group were included. Graft union and resorption were evaluated using computed tomography at 3 months to 1 year postoperatively. Patient-reported outcome measures (American Shoulder and Elbow Surgeons score, Rowe score, and satisfaction rate) were obtained at a mean follow-up of 74 months (range, 45-160 months) for Bristow and 64 months (range, 50-76 months) for Latarjet procedures. Recurrence and the rate of return to play (RTP), frequency of pain after RTP, and retirement rate after RTP were also assessed.

Results:

In 97.1% of the Latarjet procedure cases, bone union of the coracoid was achieved at 3 months postoperatively; however, bone union was achieved in only 72.7% of the Bristow procedure cases at 6 months postoperatively. Bone resorption of the coracoid process occurred in 6.1% of shoulders after the Bristow procedure, whereas 100% of shoulders showed bone resorption after the Latarjet procedure. No statistical differences were found in outcome scores between the 2 procedures. Subluxation and persistent pain after returning to sports were identified at a significantly higher rate in the Latarjet group (5 shoulders [14%] and 9 shoulders [26%], respectively) than in the Bristow group (2 shoulders [3%] and 2 shoulders [3%]) (P = .0471 and P = .001, respectively).

Conclusion:

The Latarjet procedure had an advantage in the early and high rate of bone union but was at a disadvantage in bone resorption compared with the Bristow procedure. Subluxation and pain after returning to sports were more frequent in patients who underwent the open Latarjet procedure than in those who underwent the open Bristow procedure.

Arthroscopic Technique for Distal Tibial Allograft Bone Augmentation With Suture Anchor Fixation for Anterior Shoulder Instability

Recurrent instability associated with glenoid bone loss is a commonly encountered problem after anterior shoulder dislocation. Surgical management with bony augmentation can be achieved with several allograft or autograft options. Fixation strategies also vary, including screw, suture button, or suture anchor fixation. Concerns exist regarding screw fixation because of the technical difficulty of a medial portal establishment, as well as the potential for graft osteolysis. Suture button fixation for osteochondral graft fixation has been previously described. However, no description of graft fixation using suture anchors exists. We describe an arthroscopic technique for glenoid augmentation using distal tibial allograft with suture anchor fixation.

Distal Clavicle Autograft Fixed with Buttons for the Management of Shoulder Instability with Glenoid Defect: A Case Report

CASE

In this case report, we presented the case of a 39-year-old male lawyer who presented to our tertiary care clinic with recurrent instability of his right shoulder and significant glenoid bone loss. This patient was treated with arthroscopic glenoid bone augmentation with his distal clavicle fixed with arthroscopic suture buttons.

CONCLUSION

Use of a distal clavicle autograft with arthroscopic fixation using buttons is a novel and promising solution for the management of patients with shoulder instability and associated glenoid bone loss.

A review of bone grafting techniques for glenoid reconstruction

BACKGROUND

Traumatic anterior shoulder dislocations can cause bony defects of the anterior glenoid rim and are often associated with recurrent shoulder instability. For large glenoid defects of 20-30% without a mobile bony fragment, glenoid reconstruction with bone grafts is often recommended. This review describes two broad categories of glenoid reconstruction procedures found in literature: coracoid transfers involving the Bristow and Latarjet procedures, and free bone grafting techniques.

METHODS

An electronic search of MEDLINE and PubMed was conducted to find original articles that described glenoid reconstruction techniques or modifications to existing techniques.

RESULTS

Coracoid transfers involve the Bristow and Latarjet procedures. Modifications to these procedures such as arthroscopic execution, method of graft attachment and orientation have been described. Free bone grafts have been obtained from the iliac crest, distal tibia, acromion, distal clavicle and femoral condyle.

CONCLUSION

Both coracoid transfers and free bone grafting procedures are options for reconstructing large bony defects of the anterior glenoid rim and have had similar clinical outcomes. Free bone grafts may offer greater flexibility in graft shaping and choice of graft size depending on the bone stock chosen. Novel developments tend towards minimising invasiveness using arthroscopic approaches and examining alternative non-rigid graft fixation techniques.

Clinical and Radiographic Outcomes After Arthroscopic Inlay Bristow Surgery With Screw Versus Suture Button Fixation: A Comparative Study of 117 Patients With 3.3-Year Follow-up

Background:

Some studies have advocated the use of suture button fixation during Bristow-Latarjet surgery to reduce complications associated with screw fixation. However, data comparing these fixation methods are relatively incomplete.

Purpose:

To investigate the efficacy of modified arthroscopic Bristow-Latarjet surgery and compare the clinical and radiographic outcomes using screw versus suture button fixation.

Study Design:

Cohort study; Level of evidence, 3.

Methods:

We evaluated 136 patients with traumatic anterior shoulder instability who underwent the modified arthroscopic Bristow-Latarjet surgery between June 2015 and February 2018. Of these patients, 117 who met the inclusion criteria were enrolled at a mean follow-up of 3.3 ± 0.7 years. Shoulders were separated into 2 groups based on fixation technique: screw fixation (group A; n = 63) or suture button fixation (group B; n = 54). Computed tomography imaging findings and clinical results were assessed preoperatively; immediately after operation; and postoperatively at 3 months, 6 months, 1 year, and final follow-up.

Results:

There were no significant differences between the groups in terms of postoperative clinical scores, the level of return to sports, range of motion, graft position, or reoperation rates. Bone healing was observed in 97.4% of the cases overall (114/117), with 98.4% bone union in group A and 96.3% in group B at final follow-up. Bone absorption was more common in group A (n = 30; 47.6%) compared with group B (n = 10; 18.5%) (P = .003). There were no hardware-related complications in group B, compared with 7.9% of patients in group A (P = .034). One patient in group B had a recurrent dislocation due to an unexpected event, and there were no recurrent dislocations in group A.

Conclusion:

After the modified arthroscopic Bristow-Latarjet procedure, both suture button and screw fixation methods demonstrated high bony healing rates and low risk of recurrence. Less coracoid graft resorption and no hardware-related complications were seen with suture button fixation.

Metal-Free Fixation for Free Bone-Block Reconstruction of Chronic Anteroinferior Shoulder Instability

Background

Anterior shoulder instability is common and may cause a considerable effect on quality of life. For cases with glenoid bone loss, there is still a controversial discussion regarding the optimal treatment. Most of the recent methods are using metal implants to attach the needed graft to the glenoid with reported disadvantages such as metal impingement, damage to the humeral head, cartilage destruction, and premature arthritis.

Indications

(1) Erosion-type defects with significant bone loss (>15%-20%); (2) chronic fragment-type defects if the size of the fragment is not large enough for an anatomical reconstruction; and (3) non-reconstructible, multifragmented acute fragment type of lesions.

Technique Description

After placing the patient in a lateral decubitus position and fixing the arm in a traction devise, 3 arthroscopic entries are established: a posterior portal, an anterosuperior portal, and an anteroinferior portal. A harvested tricortical iliac crest bone graft is provided with 2 drilling holes which match the drilling holes through the glenoid. The tapes are then placed from the posterior to the anterior side of the glenoid, and then the graft is passed from the anterior to the posterior side, thus compressing the cancellous side of the bone block onto the glenoid defect. A following interconnection of the sutures creates a continuous loop. The end of the tapes was loaded into a pretied racking hitch knot system, which creates sliding knots between the 2 pair of tapes, whereon the knots can be reduced to the glenoid in a symmetrical fashion. Finally, the reconstruction of the anterosuperior labrum can be done, to cover the bone block with enough soft tissue.

Results

First short-term results show radiographic consolidation after 3 months and an increased median glenoid estimated surface area at 12 months. The functional scores showed good outcomes, and there were no serious complications reported.

Discussion/Conclusion

The presented arthroscopic reconstruction of the glenoid using a tricortical bone graft and high-strength fiber tapes provides a metal-free technique which results in a high primary stability of the construct and should therefore be considered when treating anterior shoulder instability with significant bone loss.

[Arthroscopic Pushlock anchor fixation with iliac creast bone autograft in the treatment of recurrent anterior shoulder instability with critical bone defect]

OBJECTIVE

To evaluate the effectiveness of arthroscopic Pushlock anchor fixation with iliac creast bone autograft in the treatment of recurrent anterior shoulder instability with critical bone defect.

METHODS

The clinical data of 80 patients with recurrent anterior shoulder instability with critical bone defect treated by arthroscopic Pushlock anchor fixation with iliac creast bone autograft between January 2016 and January 2019 were retrospectively analyzed. The patients were all male; they were 18-45 years old at the surgery, with an average of 25 years old. The disease duration ranged from 3 months to 5 years, with an average of 2 years. The shoulder joint dislocated 3-50 times, with an average of 8 times. X-ray films, MRI, CT scans and three-dimensional reconstruction of the shoulder were performed before operation. The area of the anterior glenoid defect was 25%-45%, with an average of 27.3%. The shoulder mobility (forward flexion and external rotation in abduction at 90°), the Constant-Murley score, and the Rowe score were used to evaluate the shoulder function before operation and at last follow-up.

RESULTS

Patients were followed up 1-3 years, with an average of 2 years. No shoulder dislocation occurred again during follow-up. All partial graft absorption occurred after operation, CT scan showed that the graft absorption ratio was less than 30% at 1 week and 3 months after operation. CT three-dimensional reconstruction at 1 year after operation showed that all grafts had healed to the glenoid. The anterior glenoid bone defect was less than 5% (from 0 to 5%, with an average of 3.2%). At last follow-up, the shoulder mobility (forward flexion and external rotation in abduction at 90°), the Constant-Murley score, and the Rowe score significantly improved when compared with preoperative ones ( P<0.05). The shoulder mobility of external rotation in abduction at 90° of the affected side limited when compared with the healthy side [(6.7±5.1)°].

CONCLUSION

Arthroscopic Pushlock anchor fixation with iliac creast bone autograft has a good effectiveness in the treatment of recurrent anterior shoulder instability with critical bone defect. The method is relatively simple and the learning curve is short.

Factors affecting biomechanical strength of Latarjet constructs: A systematic review and meta-regression

BACKGROUND

The Latarjet procedure reduces recurrent glenohumeral instability but has potential hardware and graft complications. The procedure has been modified to use various screw types as well as suture buttons. Biomechanical studies have evaluated the effect of these implants on construct strength. With varying results it is unclear whether there is an optimal implant to use.

METHODS

We conducted a systematic review of human cadaveric biomechanical studies evaluating Latarjet ultimate failure load. Two independent reviewers screened articles and included them after full text review. Additional factors including implants used, graft orientation, cortices engaged, drill diameter, and screw characteristics were recorded. Meta-regression was performed on the 145 specimens from eight studies that met inclusion criteria.

RESULTS

Screw fixation resulted in a 396.8 N (95% CI, 149.8-643.7) N higher ultimate failure load against shear stresses than suture buttons (p = 0.002). There were no differences between implants for ultimate failure load against tensile forces. Tensile strength was significantly affected by drill diameter with each millimeter of increase reducing the mean ultimate failure load by 127.4 N (95% CI, 41.2-213.6) N (p = 0.004).

CONCLUSIONS

These results suggest that using screw fixation and minimizing drill diameter can obtain the maximum ultimate failure load against both shear and tensile forces in a Latarjet construct.

Arthroscopic Latarjet: 2 or 4 Cortical Buttons for Coracoid Fixation? A Case-Control Comparative Study

BACKGROUND

While 2 screws are traditionally used for coracoid bone block fixation, no gold standard technique has yet been established when using cortical buttons.

PURPOSE

To compare anatomic and clinical outcomes of the arthroscopic Latarjet procedure using either 2 or 4 buttons for coracoid bone block fixation.

STUDY DESIGN

Cohort study; Level of evidence, 3.

METHODS

A total of 23 patients with 4-button fixation (group 4B) were matched for age at surgery, sex, and follow-up to 46 patients who had 2-button fixation (group 2B). All patients underwent guided arthroscopic Latarjet (using coracoid and glenoid guides), and a tensioning device was used to rigidify the suture button construct and get intraoperative bone block compression. The primary outcome was assessment of bone block positioning and healing using computed tomography scans performed at 2 weeks and at least 6 months after surgery. The mean ± standard deviation follow-up was 49 ± 7 months (range, 24-64 months).

RESULTS

The bone block healing rate was similar in both groups: 91% in group 4B versus 95.5% in group 2B. The transferred coracoid was flush to the glenoid surface in 21 patients (91%) in group 4B and 44 patients (96%) in group 2B (P = .6); it was under the equator in 22 patients (96%) in group 4B and 44 patients (96%) in group 2B (P≥ .99). There was no secondary bone block displacement; the rate of bone block resorption was similar between the groups: 28% in group 4B and 23% in group 2B (P = .71). Patient-reported outcomes, return to sports, and satisfaction were also similar between the groups. The operating time was significantly longer in group 4B (95 vs 75 minutes; P = .009).

CONCLUSION

A 4-button fixation technique did not demonstrate any anatomic or clinical advantages when compared with a 2-button fixation technique, while making the procedure more complex and lengthening the operating time by 20 minutes. A 2-button fixation is simple, safe, and sufficient to solidly fix the transferred coracoid bone block. The use of drill guides allows accurate graft placement, while the use of a tensioning device to rigidify the suture button construct provides high rates of bone block healing with both techniques (>90%).

The Bristow-Latarjet procedure for revision of failed arthroscopic Bankart: a retrospective case series of 59 consecutive patients

BACKGROUND

Recurrence of anterior instability after arthroscopic Bankart prevents return to sports and remains a surgical challenge. We aim to assess clinical and radiologic outcomes after coracoid bone-block performed either open or under arthroscopy, for the management of failed arthroscopic Bankart PATIENTS AND METHODS: Fifty-nine consecutive patients with anterior instability recurrence after arthroscopic Bankart were revised with a Bristow or Latarjet procedure performed either open (25 cases) or under arthroscopy (34 cases). Patients were reviewed for clinical and radiologic examination at a minimum 2-year follow-up. Glenohumeral bony lesions were evaluated preoperatively with computed tomographic scans. Postoperative bone-block position, union, and postinstability arthritis were also evaluated.

RESULTS

The mean follow-up was 89 months (24-193). The epidemiologic analysis showed that patients with failed arthroscopic Bankart were young (age <23 years), 58 (98%) were practicing sports, with contact/forced overhead sports (53%), often in competition (53%), had hyperlaxity (71%), and for the most part of them glenohumeral bone loss (88%). Their mean preoperative Instability Severity Index Score was 5.4 ± 2.2 points. After revision with Bristow-Latarjet procedure, 53 patients (91%) returned to sports, 37 (70%) to their previous sports activity, and 17 (46%) to their previous level. No patient suffered recurrent dislocation. Four patients (7%) had recurrent subluxations, all after open procedure; 8 patients (14.5%) had persistent anterior apprehension. A large and deep Hill-Sachs lesion was a risk factor for persistent anterior apprehension (P = .002) and lower level when returned to sports (P = .04). Ninety-two percent of bone-blocks were positioned flush with the glenoid anterior rim, with 84% of bone union. At last follow-up, 5% of patients had severe postinstability osteoarthritis (Samilson 4).

CONCLUSION

The Bristow-Latarjet, performed either open or under arthroscopy, is an efficient procedure to restore shoulder stability and allow returning to sports in patients with failed arthroscopic Bankart and glenoid bone loss. Patients with a large and deep Hill-Sachs lesion had more persistent anterior apprehension and a lower sports level.

Arthroscopic Distal Clavicular Autograft for Congruent Glenoid Reconstruction

Arthroscopic distal clavicular autograft (DCA) is effective in shoulder instability with glenoid bone loss. The original technique uses an osteochondral autograft, fixed with screws or suture anchors. We developed a modified procedure called "congruent arc DCA" characterized by (1) use of drilling guides to optimize graft positioning and make the all-arthroscopic procedure safer and reproducible; (2) rotation of the DCA of 90° to reach a congruent arc with its undersurface; (3) fixation of the graft with cortical buttons to simplify its intra-articular passage, avoid hardware problems, and facilitate possible revision surgery; and (4) intraoperative use of a suture tensioner to achieve satisfactory compression of the graft and increase its consolidation.

Modification of the Traditional Open Latarjet Technique with the Use of Sutures and Cortical Buttons Instead of Screws

In this article we describe a modification of the open Latarjet technique, using sutures and cortical buttons, for the fixation of the coracoid. The transfer of the coracoid to the anterior glenoid is a popular technique used for complex shoulder instability. The technique is proven to be effective with consistently good results but complications have been reported related to the screws used for the fixation of the coracoid. Recent studies confirm that the suture-button technique for the fixation of the coracoid is biomechanically comparable to the screw fixation. The proposed technique combines the advantages of the open approach and avoids the use of metal screws, potentially minimizing hardware-related complications.

Non-rigid fixation of the glenoid bone block for patients with recurrent anterior instability and major glenoid bone loss: A systematic review

BACKGROUND

New types of glenoid bone block fixation, involving suture buttons, suture anchors or even implant-free impaction of the graft, have been recently introduced. In contrast to screws which allow for a rigid fixation of the bone block, these alternative procedures provide a non-rigid type of fixation.

METHODS

Two reviewers independently conducted the search in a systematic way (according to the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) using the MEDLINE/PubMed database and the Cochrane Database of Systematic Reviews. These databases were queried with the terms "Latarjet" OR "Eden-Hybbinette" OR "bone block" AND "anterior" AND "shoulder" AND "instability."

RESULTS

Eight out of the 325 initial studies were finally chosen according to our inclusion-exclusion criteria. In total, 750 patients were included in this review. The overall anterior instability recurrence rate for patients treated with non-rigid fixation was 2.6%, while the overall rate of non-union or graft osteolysis was 5.4%.

CONCLUSIONS

Regardless of the graft type, bone block non-rigid fixation showed satisfactory clinical and functional outcomes for the treatment of anterior shoulder instability with substantial glenoid bone deficiency. Furthermore, non-rigid fixation resulted in adequate bone graft healing and osseous incorporation. Lastly, given the relative lack of data, further prospective controlled studies are required to assess bone block non-rigid fixation procedures in comparison with the traditional rigid (with screws) fixation techniques.

LEVEL

Systematic review, IV.

Excellent Clinical and Radiological Midterm Outcomes for the Management of Recurrent Anterior Shoulder Instability by All-Arthroscopic Modified Eden-Hybinette Procedure Using Iliac Crest Autograft and Double-Pair Button Fixation System: 3-Year Clinical Case Series With No Loss to Follow-Up

PURPOSE

To evaluate the clinical, functional, and radiological midterm outcomes of the all-arthroscopic modified Eden-Hybinette procedure in patients with recurrent anterior shoulder instability.

METHODS

A retrospective, single-center case series with prospectively collected data was conducted. The inclusion criterion was traumatic recurrent anterior shoulder instability with significant glenoid bone loss; patients with atraumatic or multidirectional instability were excluded. An all-arthroscopic modified Eden-Hybinette procedure using iliac crest autograft and double-pair button fixation was carried out. All patients were postoperatively assessed for recurrence and apprehension. Shoulder range of motion values and functional scores, including American Shoulder and Elbow Surgeons Score, Oxford instability, Rowe instability, and Walch-Dupplay, were recorded. Graft positions, healing, and absorption were evaluated with computed tomography. Comparisons of values were performed with paired t tests for normally distributed differences and with nonparametric Wilcoxon's signed rank test otherwise.

RESULTS

The final study cohort included 28 patients, mean age 36 ± 10 years, and mean follow-up period 43 ± 6 months (range 36 to 53). Median glenoid bone loss was 12.4% (range 8% to 33%). No recurrence occurred, no subjective shoulder instability was reported, and no major complications were documented through the last follow-up. Postoperative shoulder range of motion had no significant differences compared with the healthy side. All final postoperative functional scores significantly increased to show excellent results compared with preoperative values. All grafts were positioned and healed optimally, and none was completely reabsorbed.

CONCLUSIONS

The all-arthroscopic modified Eden-Hybinette procedure is safe, leading to excellent clinical and radiological midterm outcomes in patients with recurrent anterior shoulder instability. This technique restores glenoid bone defects and preserves the normal shoulder anatomy.

LEVEL OF EVIDENCE

IV, therapeutic, retrospective case series.

Arthroscopic double-button Latarjet: two-thirds of bone block healed at 90 days

PURPOSE

The aim of this study was to evaluate the union rate and risk factors for delayed union in the early postoperative period after an arthroscopic Latarjet with double-button fixation.

METHOD

In a retrospective study, postoperative CT scans at 3 months were analysed following an arthroscopic Latarjet with double-button fixation used to treat anterior shoulder instability. Healing of the bone block, its position in the sagittal and coronal planes, and the contact area graft/scapula were analysed.

RESULTS

Ninety-eight CT scans (98 patients) were included. The rate of healing at 3 months was 63/98 (64%) and four grafts clearly migrated. The position was perfectly flush to the glenoid rim in 67% and under the equator in 96%. The mean contact graft/scapula area was 135 mm 2 (4-420). In multivariate analysis, the risk of non-union at 3 months was associated with tobacco consumption (p = 0.001, aOR = 12.17 95% CI [2.62-56.49]), absence of preoperative glenoid bone defect (p = 0.003, aOR = 8.06 95% CI [2.06-31.56]), and a contact area graft/scapula less than 120 mm 2 (p = 0.010, aOR = 5.25 95% CI [1.50-18.40]). Among 31 non-united grafts, 93% definitively healed on CT scan at 1 year, leaving an overall rate of 93% of united grafts at last follow-up.

CONCLUSIONS

The rate of union at 3 months after an arthroscopic Latarjet with double-button fixation was 64%, reaching 93% at 1 year. This procedure should be carefully indicated in case of tobacco use or instability without glenoid bone defect, especially when the shoulder is exposed to high-energy trauma in the early phase after surgery.

Mechanical behavior of screw versus Endobutton for coracoid bone-block fixation

INTRODUCTION

Arthroscopic coracoid bone-block fixation by Endobutton was developed to avoid the complications associated with screwing. However, few studies have assessed the mechanical characteristics of the two. The aim of the present study was to assess and compare fixation rigidity by screw versus Endobutton. The study hypothesis was that rigidity is lower with Endobutton than with screws.

MATERIAL AND METHOD

3D print-outs of a glenoid and a coracoid process were obtained from CT scans of a patient showing anterior shoulder instability with significant bone defect. Four types of coracoid fixation were implemented: 1 or 2 4.5mm malleolar screws, and 1 or 2 Endobuttons. Three specimens per assembly were placed on a specific test bench. Lateromedial bone-block compression was exerted at 0.1mm/sec at 3 points: superior, central, inferior. The resultant force and bone-block displacement were recorded.

RESULTS

Mean fixation rigidity with 1 screw, 2 screws, 1 Endobutton and 2 Endobuttons was respectively 158N/mm (range, 133-179), 249N/mm (241-259), 10N/mm (5-13) and 14N/mm (13-15), with significant difference between the screw and Endobutton groups (p<0.001). Displacement was greater with 1 than 2 Endobuttons under superior or inferior force, while the difference was non-significant under central force (7.45 vs 6.93mm; p=0.53) CONCLUSIONS: Screw fixation showed greater rigidity, while the Endobutton assembly showed less tension, leading to greater bone-block mobilization. The interest of using two Endobuttons is to reduce displacement under polar pressure. the present biomechanical study confirmed the mechanical vulnerability of bone-blocks fixed by endobutton until consolidation is achieved.

LEVEL OF EVIDENCE

Biomechanical study.

Latarjet Cerclage: The Metal-Free Fixation

The Latarjet technique is a widely used technique for anterior shoulder instability with glenoid bone defects, irreparable capsuloligamentous lesion, or in patients at greater risk of recurrence. The use of this technique has been reported to obtain satisfactory clinical and biomechanical results. Although other methods exist, the coracoid process is typically fixed with 2 metal screws. Complications related to metal fixation are very frequently reported. In an attempt to avoid these complications, we developed this arthroscopically assisted metal-free Latarjet technique in which we fix a coracoid graft using four cerclage tapes to achieve a strong, stable fixation, thus mimicking a plate.