Effect of molecular weight on the shear-induced crystallization of poly(lactic acid)

The Effects of Nucleating Agents and Processing on the Crystallization and Mechanical Properties of Polylactic Acid: A Review

Polylactic acid (PLA) is a biobased, biodegradable, non-toxic polymer widely considered for replacing traditional petroleum-based polymer materials. Being a semi-crystalline material, PLA has great potential in many fields, such as medical implants, drug delivery systems, etc. However, the slow crystallization rate of PLA limited the application and efficient fabrication of highly crystallized PLA products. This review paper investigated and summarized the influence of formulation, compounding, and processing on PLA's crystallization behaviors and mechanical performances. The paper reviewed the literature from different studies regarding the impact of these factors on critical crystallization parameters, such as the degree of crystallinity, crystallization rate, crystalline morphology, and mechanical properties, such as tensile strength, modulus, elongation, and impact resistance. Understanding the impact of the factors on crystallization and mechanical properties is critical for PLA processing technology innovations to meet the requirements of various applications of PLA.

Enhancement in Crystallizability of Poly(L-Lactide) Using Stereocomplex-Polylactide Powder as a Nucleating Agent

High-molecular-weight poly(L-lactide) (HMW-PLLA) is a promising candidate for use as a bioplastic because of its biodegradability and compostability. However, the applications of HMW-PLLA have been limited due to its poor crystallizability. In this work, stereocomplex polylactide (scPLA) powder was prepared by precipitation of a low-molecular-weight poly(L-lactide)/poly(D-lactide) (LMW-PLLA/LMW-PDLA) blend solution and investigated for use as a fully-biodegradable nucleating agent for HMW-PLLA compared to LMW-PLLA powder. The obtained LMW-PLLA and scPLA powders with a nearly spherical shape showed complete homo- and stereocomplex crystallites, respectively. HMW-PLLA/LMW-PLLA powder and HMW-PLLA/scPLA powder blends were prepared by melt blending. The LMW-PLLA powder was homogeneously melted in the HMW-PLLA matrices, whereas the scPLA powder had good phase compatibility and was well-dispersed in the HMW-PLLA matrices, as detected by scanning electron microscopy (SEM). It was shown that the enthalpies of crystallization (ΔHc) upon cooling scans for HMW-PLLA largely increased and the half crystallization time (t1/2) dramatically decreased as the scPLA powder content increased; however, the LMW-PLLA powder did not exhibit the same behavior, as determined by differential scanning calorimetry (DSC). The crystallinity content of the HMW-PLLA/scPLA powder blends significantly increased as the scPLA powder content increased, as determined by DSC and X-ray diffractometry (XRD). In conclusion, the fully biodegradable scPLA powder showed good potential for use as an effective nucleating agent to improve the crystallization properties of the HMW-PLLA bioplastic.

Self-Assembly of Lipid Mixtures in Solutions: Structures, Dynamics Processes and Mechanical Properties

The self-assembly of lipid mixtures in aqueous solution was investigated by dissipative particle dynamics simulation. Two types of lipid molecules were modelled, where three mixed structures, i.e., the membrane, perforated membrane and vesicle, were determined in the self-assembly processes. Phase behaviour was investigated by using the phase diagrams based on the tail chain lengths for the two types of lipids. Several parameters, such as chain number and average radius of gyration, were employed to explore the structural formations of the membrane and perforated membrane in the dynamic processes. Interface tension was used to demonstrate the mechanical properties of the membrane and perforated membrane in the equilibrium state and dynamics processes. Results help us to understand the self-assembly mechanism of the biomolecule mixtures, which has a potential application for designing the lipid molecule-based bio-membranes in solutions.

The Role of Structure in Polymer Rheology: Review

The review is devoted to the analysis of the current state of understanding relationships among the deformation-induced structure transformations, observed rheological properties, and the occurrence of non-linear effects for polymer liquids (melts, solutions, and composites). Three levels of non-linearity are the base for consideration. The first one concerns changes in the relaxation spectra of viscoelastic liquids, which are responsible for weak non-linear phenomena. The second one refers to the strong non-linearity corresponding to such changes in the structure of a medium that leads to the emergence of a new relaxation state of a matter. Finally, the third one describes the deformation-induced changes in the phase state and/or the occurring of bifurcations and instability in flow and reflects the thermodynamic non-linear behavior. From a structure point of view, a common cause of the non-linear effects is the orientation of macromolecules and changes in intermolecular interaction, while a dominant factor in describing fluid dynamics of polymer liquids is their elasticity. The modern understanding of thixotropic effects, yielding viscoplastic materials, deformation-induced phase transition, and the experimental observations, demonstrating direct correlations between the structure and rheology of polymer liquids, are the main objects for discussion. All these topics are reviewed and discussed mainly on the basis of the latest five-year publications.

Entirely environment-friendly polylactide composites with outstanding heat resistance and superior mechanical performance fabricated by spunbond technology: Exploring the role of nanofibrillated stereocomplex polylactide crystals

This study aims at investigating the manufacturing and characterization of all-polylactide composites prepared by melt spunbond spinning technology. To do so, a series of asymmetric stereocomplex polylactide (SC-PLA) blends (PLLA 95 wt%/PDLA 5 wt%) was melt spun. To examine the impact of molecular structure of PDLA, the blends of linear PLLA, and low and high molecular weight as well as branched PDLAs, were subjected to a single step spunbond process. DSC thermograms of the samples showed two melting temperatures at around 170 °C and 210 °C, which were attributed to the melting of homo and stereocomplex crystals, respectively. The samples were spun at 190 °C, between the homo and stereocomplex crystals' melting temperatures, and at 230 °C, above the stereocomplex crystals' melting temperature. Morphology images showed the formation of fibers in the range of 40-50 μm. Shear rheological measurements revealed that the spun SC-PLA samples had a substantially higher viscosity and storage modulus in the low frequency region, and higher shear thinning behavior, compared to the non-spun samples. Extensional rheology measurements also showed that the spun samples demonstrated strain hardening behavior. Substantial enhancement of rheological properties was noted for the samples containing the branched and high molecular weight PDLA spun at 230 °C. After etching, the spun samples at 190 °C exhibited small spherical crystals with diameters in the range of 80-90 nm, whereas comparatively thin fibers in the size range of 60-70 nm were observed for the samples spun at 230 °C. Remarkable enhancements up to 100% and 60% was noted for the tensile modulus and strength, respectively, of the spun SC-PLA samples. The spun fibers also demonstrated a considerable reduction in boiling water and hot air shrinkage. The distinctive role of nanofibrillated stereocomplex crystals as a rheology modifier and a crystallization nucleating agent makes PLA more sustainable and paves the way for the fabricated all-PLA composites in applications requiring high heat resistance and superior mechanical performance. The present study unequivocally indicates a huge potential for the sustainable entirely all-PLA products manufactured by fiber in fiber and, indeed, unfolds unknown opportunities for PLA-based merchandises in future.

Asymmetric Lipid Membranes under Shear Flows: A Dissipative Particle Dynamics Study

We investigate the phase behavior of the asymmetric lipid membranes under shear flows, using the dissipative particle dynamics simulation. Two cases, the weak and strong shear flows, are considered for the asymmetric lipid microstructures. Three typical asymmetric structures, the membranes, tubes, and vesicle, are included in the phase diagrams, where the effect of two different types of lipid chain length on the formation of asymmetric membranes is evaluated. The dynamic processes are demonstrated for the asymmetric membranes by calculating the average radius of gyration and shape factor. The result indicates that different shear flows will affect the shape of the second type of lipid molecules; the shape of the first type of lipid molecules is more stable than that of the second type of lipid molecules. The mechanical properties are investigated for the asymmetric membranes by analyzing the interface tension. The results reveal an absolute pressure at the junctions of different types of particles under the weak shear flow; the other positions are almost in a state of no pressure; there is almost no pressure inside the asymmetric lipid membrane structure under the strong shear flow. The findings will help us to understand the potential applications of asymmetric lipid microstructures in the biological and medical fields.

Effect of Molar Mass on Critical Specific Work of Flow for Shear-Induced Crystal Nucleation in Poly (l-Lactic Acid)

The concept of specific work of flow has been applied for the analysis of critical shearing conditions for the formation of crystal nuclei in poly (l-lactic acid) (PLLA). Systematic variation in both time and rate of shearing the melt in a parallel-plate rheometer revealed that these parameters are interconvertible regarding the shear-induced formation of crystal nuclei; that is, low shear rate can be compensated for by increasing the shear time and vice versa. This result supports the view that critical shearing conditions can be expressed by a single quantity, providing additional options for tailoring polymer processing routes when enhanced nuclei formation is desired/unwanted. Analysis of PLLA of different mass-average molar masses of 70, 90, 120, and 576 kDa confirmed improved shear-induced crystal nucleation for materials of higher molar mass, with critical specific works of flow, above which shear-induced nuclei formation occurs, of 550, 60, 25, and 5 kPa, respectively.

Self-assembly of phospholipid molecules in solutions under shear flows: Microstructures and phase diagrams

Shear-induced microstructures and their phase diagrams were investigated for phospholipid molecules in aqueous solution by dissipative particle dynamic simulation. Self-assembled microstructures, including spherical and cylindrical micelles, spherical vesicles, lamellae, undulated lamellae, perforated lamellae, and continuous networks, were observed under various shear flows and phospholipid concentrations, where the spatial inhomogeneity and symmetry were analysed. A series of phase diagrams were constructed based on the chain lengths under various phospholipid concentrations. The phase distributions showed that the structures with spherical symmetry could be shear-induced to structures with cylindrical symmetry in the dilute solutions. In the semi-concentrated solutions, the lamellae were located in most spaces under zero shear flows, which could be shear-induced into undulated lamellae and then into cylindrical micelles. For the concentrated solutions, the strong shear flows oriented the directions of multilayer lamellae and phase transitions appeared between several cylindrical network structures. These observations on shear-induced microstructures and their distributions revealed a promising approach that could be used to design bio-microstructures based on phospholipid molecules under shear flows.

Replication of Micro- and Nanofeatures in Injection Molding of Two PLA Grades with Rapid Surface-Temperature Modulation

The production by injection molding of polymeric components having micro- and nanometrical surfaces is a complex task. Generally, the accurate replication of micro- and nanometrical features on the polymeric surface during the injection-molding process is prevented by of the low mold temperature adopted to reduce cooling time. In this work, we adopt a system that allows fast heating of the cavity surface during the time the melt reaches the cavity, and fast cooling after heater deactivation. A nickel insert with micro- and nanofeatures in relief is located on the cavity surface. Replication accuracy is analyzed by Atomic Force Microscopy under different injection-molding conditions. Two grades of polylactic acid with different viscosity have been adopted. The results indicate that the higher the cavity surface temperature is, the higher the replication accuracy is. The viscosity has a significant effect only in the replication of the microfeatures, whereas its effect results are negligible in the replication of nanofeatures, thus suggesting that the interfacial phenomena are more important for replication at a nanometric scale. The evolution of the crystallinity degree on the surface also results in a key factor on the replication of nanofeatures.