Characterization of titanium dioxide nanoparticle removal in simulated drinking water treatment processes

Ti-containing NPs in raw water and their removal with conventional treatments in four water treatment plants in Taiwan

The ingestion of Ti-containing nanoparticles from drinking water has emerged as a concern in recent years. This study therefore aimed to characterize Ti-containing nanoparticles in water samples collected from four water treatment plants in Taiwan and to explore the challenges associated with measuring them at low levels using single particle-inductively coupled plasma mass spectrometry. Additionally, the study sought to identify the most effective processes for the removal of Ti-containing nanoparticles. For each water treatment plant, two water samples were collected from raw water, sedimentation effluent, filtration effluent, and finished water, respectively. Results revealed that Ti-containing nanoparticles in raw water, with levels at 8.69 μg/L and 296.8 × 103 particles/L, were removed by approximately 35% and 98%, respectively, in terms of mass concentration and particle number concentration, primarily through flocculation and sedimentation processes. The largest most frequent nanoparticle size in raw water (112.0 ± 2.8 nm) was effectively reduced to 62.0 ± 0.7 nm in finished water, while nanoparticles in the size range of 50-70 nm showed limited changes. Anthracite was identified as a necessary component in the filter beds to further improve removal efficiency at the filtration unit. Moreover, the most frequent sizes of Ti-containing nanoparticles were found to be influenced by salinity. Insights into the challenges associated with measuring low-level Ti-containing nanoparticles in aqueous samples provide valuable information for future research and management of water treatment processes, thereby safeguarding human health.

Stability, aggregation, and sedimentation behaviors of typical nano metal oxide particles in aqueous environment

The wide use of nano metal oxide particles (NMOPs) brings about their inevitable release into the water environment, affecting the environment and human health. Therefore, the stability, aggregation, and sedimentation process of four typical NMOPs (ZnO NPs, CeO₂ NPs, TiO₂ NPs, and CuO NPs) were investigated in artificial water and real municipal sewage to reveal their complicated behavior. Results showed that NMOPs aggregated at the pH of zero-charge point, and their hydrodynamic diameters and aggregation rates could reach the maximum values. The hydrodynamic diameters and aggregation rates of ZnO NPs, CeO₂ NPs, TiO₂ NPs, and CuO NPs at the zero-charge point were 617, 1760, 870, 1502 nm, and 31.7, 1158.1, 48.3, 115.7 nm/min, respectively. In addition, the dissolution of NMOPs led to the sedimentation rates under acidic conditions being much lower than those under neutral and alkaline conditions. The aggregation and sedimentation performance of NMOPs were affected by not only pH but also ionic strength (IS) and species. The aggregation rates of NMOPs increased with the increase of IS (0-10 mM), and the maximum aggregation rate of CeO₂ NPs was 470.1 nm/min (pH = 7 and CaCl₂ = 10 mM). According to Coulomb's law, divalent cations (Mg²⁺, Ca²⁺) were more competitively adsorbed on the surface of NMOPs than monovalent cations (K⁺, Na⁺), which increased the zeta potential and aggregation rate of NMOPs. Furthermore, the NMOPs were easier to aggregate in municipal sewage because of the homogeneous aggregation between nanoparticles and heterogeneous aggregation with natural colloids. The total interaction energy between NMOPs was calculated by the classical Derjaguin-Landau-Verwey-Overbeek (DLVO) theoretical formula, which was consistent with the experimental results.

Occurrence of titanium dioxide nanoparticle in Taihu Lake (China) and its removal at a full-scale drinking water treatment plant

The occurrence of titanium dioxide nanoparticle (TNP), an emerging contaminant, in Taihu Lake of China was investigated. Ti was present at a concentration of 224 ± 59 μg/L in the water samples collected from a water source in east Taihu Lake. Approximately 0.19% of the Ti-containing matter was at the nano-scale. Scanning Electron Microscope analysis verified the existence of Ti-containing components, such as TiOx and FeTiOx. Furthermore, Ti K-edge X-ray absorption near-edge structure spectroscopy was used to detect the phase composition of nano-scaled Ti-containing matter. The spectra showed the three characteristic peaks of TiO2 in the samples, suggesting the occurrence of TNP in Taihu Lake. A least-squares linear combination fitting analysis indicated that the TNP concentration in the water source was ~0.77 μg/L in water and ~0.85 μg/g-dry in sediment. The removal performance of the TNP at a full-scale conventional drinking water treatment plant indicated that ~61% of TNP was removed via coagulation/sediment, sand filtration, and disinfection/clear water reservoir. The coagulation/sediment process accounted for approximately 70% of the total removed TNP. The finished water contained ~ 0.30 μg/L TNP. This study is the first that reported the presence and transport of TNP in a full-scale drinking water treatment system.

Potential hazards associated with interactions between diesel exhaust particulate matter and pulmonary surfactant

Long term exposure to diesel exhaust particulate matter (DEPM) can induce numerous adverse health effects to the respiratory system. Understanding the interaction between DEPM and pulmonary surfactant (PS) can be an essential step toward preliminary evaluation of the impact of DEPM on pulmonary health. Herein, DEPM was explored for its interaction with 1,2-dipalmitoyl-sn-glycerol-3-phosphocholine (DPPC), the major component of PS. The results indicated that the surface pressure-area (π-A) isotherms of DPPC monolayers shifted toward lower molecular areas and the compression modulus (C_S^-1) reduced in the presence of DEPM. Atomic force microscopy image showed that DEPM can disrupt the ultrastructure of DPPC monolayers along with the direction of lateral compression. In addition, DPPC can in turn condition the surface properties of DEPM, permitting its agglomeration in aqueous media, which was attributed to the adsorption of DEPM to DPPC. Furthermore, the particle-bound polycyclic aromatic hydrocarbons (PAHs) could be desorbed from DEPM by the solubilization of DPPC and it was positively correlated with the hydrophobicity of PAHs. These findings revealed the toxicity of DEPM-associated PAHs and the role of DPPC in facilitating the removal of the inhaled particles, which can provide a new insight into the potential hazards of airborne particles on lung health.

Effects of interactions between humic acid and heavy metal ions on the aggregation of TiO2 nanoparticles in water environment

Nanoparticles (NPs), heavy metal and natural organic matter (NOM) may simultaneously exist in the aquatic environment, where they will affect the behavior of each other and may enhance their toxicities. Studies on the influences of interactions between NOM and heavy metal ions on the behavior of NPs are scarce. In this study, combined effects of Pb²⁺ and HA on the aggregation behavior of TiO₂ NPs in water environment were investigated by Dynamic light scattering (DLS) and Nanoparticle tracking analysis (NTA). The results illustrated that interactions between Pb²⁺ and HA could case the aggregation of TiO₂ NPs obviously. The concurrence of Pb²⁺ and HA resulted in decreased critical coagulation concentration (CCC) and increased attachment efficiencies. Meanwhile, we found that the addition sequences of HA and heavy metal clearly influenced the aggregation kinetics of TiO₂ NPs. At different addition sequences, the complex reaction between Pb²⁺ and HA changed the surface charge of TiO₂ NPs, and caused the different aggregation behavior which depended on the complex locations and complex sites. Furthermore, the excitation-emission-matrix (EEM) fluorescence spectra was used to verify the significant effects of the complex interactions between Pb²⁺ and HA on the aggregation of TiO₂ NPs. Our results would be significant for interpreting TiO₂ behavior in the complicated water system. The complexation between Pb²⁺ and HA promoted the aggregation of TiO₂ NPs, meanwhile, complex locations and complex sites played an important role.

A review on the interactions between engineered nanoparticles with extracellular and intracellular polymeric substances from wastewater treatment aggregates

Engineered nanoparticles (ENPs) will inevitably enter wastewater treatment plants (WWTPs) due to their widespread application; thus, it is necessary to study the migration and transformation of nanoparticles in sewage treatment systems. Extracellular polymeric substances (EPSs) such as polysaccharides, proteins, nucleic acids, humic acids and other polymers are polymers released by microorganisms under certain conditions. Intracellular polymeric substances (IPSs) are microbial substances contained in the body with compositions similar to those of extracellular polymers. In this review, we summarize the characteristics of EPSs and IPSs from sewage-collecting microbial aggregates containing pure bacteria, activated sludge, granular sludge and biofilms. We also further investigate the dissolution, adsorption, aggregation, deposition, oxidation and other chemical transformation processes of nanoparticles, such as metals, metal oxides, and nonmetallic oxides. In particular, the review deeply analyzes the migration and transformation mechanisms of nanoparticles in EPS and IPS matrices, including physical, chemical, biological interactions mechanisms. Moreover, various factors, such as ionic strength, ionic valence, pH, light, oxidation-reduction potential and dissolved oxygen, influencing the interaction mechanisms are discussed. In recent years, studies on the interactions between EPSs/IPSs and nanoparticles have gradually increased, but the mechanisms of these interactions are seldom explored. Therefore, developing a systematic understanding of the migration and transformation mechanisms of ENPs is significant.

Interactions between silver nanoparticles and other metal nanoparticles under environmentally relevant conditions: A review

Global production of engineered nanoparticles (ENPs) continues to increase due to the demand of enabling properties in consumer products and industrial applications. Release of individual or aggregates of ENPs have been shown to interact with one another subsequently resulting in adverse biological effects. This review focuses on silver nanoparticles (AgNPs), which are currently used in numerous applications, including but not limited to antibacterial action. Consequently, the release of AgNPs into the aquatic environment, the dissociation into ions, the binding to organic matter, reactions with other metal-based materials, and disruption of normal biological and ecological processes at the cellular level are all potential negative effects of AgNPs usage. The potential sources of AgNPs includes leaching of intact particles from consumer products, disposal of waste from industrial processes, intentional release into contaminated waters, and the natural formation of AgNPs in surface and ground water. Formation of natural AgNPs is greatly influenced by different chemical parameters including: pH, oxygen levels, and the presence of organic matter, which results in AgNPs that are stable for several months. Both engineered and natural AgNPs can interact with metal and metal oxide particles/nanoparticles. However, information on the chemical and toxicological interactions between AgNPs and other nanoparticles is limited. We have presented current knowledge on the interactions of AgNPs with gold nanoparticles (AuNPs) and titanium dioxide nanoparticles (TiO₂ NPs). The interaction between AgNPs and AuNPs result in stable bimetallic Ag-Au alloy NPs. Whereas the interaction of AgNPs with TiO₂ NPs under dark and light conditions results in the release of Ag⁺ ions, which may be subsequently converted back into AgNPs and adsorb on TiO₂ NPs. The potential chemical mechanisms and toxic effects of AgNPs with AuNPs and TiO₂ NPs are discussed within this review and show that further investigation is warranted.

Review of analytical studies on TiO2 nanoparticles and particle aggregation, coagulation, flocculation, sedimentation, stabilization

Titanium dioxide (TiO₂) nanoparticles (NPs) have been widely used in industrial and consumer products. Comprehensive and accurate detection, characterization, and quantification of TiO₂ NPs are important for understanding the specific property, behavior, fate, and potential risk of TiO₂ NPs in natural and engineered environments. This review provides a summary of recent analytical studies of TiO₂ NPs and their aggregation, coagulation, flocculation, sedimentation, stabilization under a wide range of conditions and processes. Much attention is paid on sample preparation prior to an analytical procedure, analysis of particle size, morphology, structure, state, chemical composition, surface properties, etc., via measurements of light scattering and zeta potential, microscopy, spectroscopy, and related techniques. Recently, some advanced techniques have also been explored to characterize TiO₂ NPs and their behaviors in the environment. Many issues must be considered including distinction between engineered TiO₂ NPs and their naturally occurring counterparts, lack of reference materials, interlaboratory comparison, when analyzing low concentrations of TiO₂ NPs and their behaviors in complex matrices. No "ideal" technique has emerged as each technique has its own merits, biases, and limitations. Multi-method approach is highlighted to provide in-depth information. Improvements of analytical method for determination of TiO₂ NPs have been recommended to be together with exposure modelers and ecotoxicologists for maximum individual and mutual benefit. Future work should focus on developing analytical technology with the advantages of being reliable, sensitive, selective, reproducible, and capable of in situ detection in complicated sample system.

Secondary Particle Formation during the Nonaqueous Synthesis of Metal Oxide Nanocrystals

This study aims to elucidate the aggregation and agglomeration behavior of TiO₂ and ZrO₂ nanoparticles during the nonaqueous synthesis. We found that zirconia nanoparticles immediately form spherical-like aggregates after nucleation with a homogeneous size of 200 nm, which can be related to the metastable state of the nuclei and the reduction of surface free energy. These aggregates further agglomerate, following a diffusion-limited colloid agglomeration mechanism that is additionally supported by the high fractal dimension of the resulting agglomerates. In contrast, TiO₂ nanoparticles randomly orient and follow a reaction-limited colloid agglomeration mechanism that leads to a dense network of particles throughout the entire reaction volume. We performed in situ laser light transmission measurements and showed that particle formation starts earlier than previously reported. A complex population balance equation model was developed that is able to simulate particle aggregation as well as agglomeration, which eventually allowed us to distinguish between both phenomena. Hence, we were able to investigate the respective agglomeration kinetics with great agreement to our experimental data.

Reactive oxygen species and other biochemical and morphological biomarkers in the gills and kidneys of the Neotropical freshwater fish, Prochilodus lineatus, exposed to titanium dioxide (TiO2) nanoparticles

This study investigated the action of titanium dioxide nanoparticles (TiO₂-NPs), on the gills and kidneys of Neotropical freshwater fish, Prochilodus lineatus, with emphasis on reactive oxygen species (ROS) production, antioxidant responses, and morphological changes. Fish were exposed to 1, 5, 10, and 50 mg L^-1 nominal TiO₂-NPs suspended into water for 2 or 14 days. In gills, ROS decreased and glutathione (GSH) increased after 2 days, while ROS and GSH increased and superoxide dismutase activity decreased after 14 days. In kidneys, GSH and lipoperoxidation increased after 2 days and catalase activity decreased after 14 days. Common histopathologies in gills were epithelium hyperplasia, cellular hypertrophy, proliferation of mitochondria-rich cells (MRC), and lamellar stasis; in kidneys, there were cellular and nuclear hypertrophy, focal tubule degeneration, necrosis, and melanomacrophage (MM) proliferation. Although environmentally unlikely, high-dose exposures clarified biological effects of TiO₂-NPs, such as ROS formation and MRC responses in the gills, which may impair ionic balance. It was also found that MM are likely responsible for eliminating NPs in the kidney. These findings will help to regulate TiO₂-NP disposal, but longer-term studies are still needed.

Low risk posed by engineered and incidental nanoparticles in drinking water

Natural nanoparticles (NNPs) in rivers, lakes, oceans and ground water predate humans, but engineered nanoparticles (ENPs) are emerging as potential pollutants due to increasing regulatory and public perception concerns. This Review contrasts the sources, composition and potential occurrence of NNPs (for example, two-dimensional clays, multifunctional viruses and metal oxides) and ENPs in surface water, after centralized drinking water treatment, and in tap water. While analytical detection challenges exist, ENPs are currently orders of magnitude less common than NNPs in waters that flow into drinking water treatment plants. Because such plants are designed to remove small-sized NNPs, they are also very good at removing ENPs. Consequently, ENP concentrations in tap water are extremely low and pose low risk during ingestion. However, after leaving drinking water treatment plants, corrosion by-products released from distribution pipes or in-home premise plumbing can release incidental nanoparticles into tap water. The occurrence and toxicity of incidental nanoparticles, rather than ENPs, should therefore be the focus of future research.

Mitochondria-rich cells adjustments and ionic balance in the Neotropical fish Prochilodus lineatus exposed to titanium dioxide nanoparticles

Manufactured titanium dioxide nanoparticles (TiO₂-NP) have been intensely applied in numerous industrial products and may be a risk for aquatic systems as they are not completely removed from domestic and industrial wastes after water treatment. This study evaluated the osmo- and ionic balance, Na⁺/K⁺-ATPase, H⁺-ATPase and carbonic anhydrase activities and the mitochondria-rich cells (MRC) in the gills and kidney of the Neotropical fish Prochilodus lineatus after 2 (acute) and 14 (subchronic) days of exposure to nominal 0, 1, 5, 10 and 50 mg L^-1 TiO₂-NP. The nominal concentrations corresponded to 0.0, 0.6, 1.6, 2.7 and 18.1 mg L^-1 suspended TiO₂-NP, respectively, in the water column one hour after NP introduction and were maintained for at least 24 h. Acute exposure to TiO₂-NP decreased plasma osmolality and Ca²⁺ levels. Na⁺/K⁺-ATPase, H⁺-ATPase and carbonic anhydrase activities were inhibited in the gills, but not in the kidney. Total MRC density did not change in gills and kidneys. At gill surface, total MRC density decreased in fish exposed to 50 mg L^-1 TiO₂-NP and the total MRC fractional surface area unchanged although, there were some changes in the fractional area of MRC with apical microvilli (MRCm) and MRC with apical sponge-like structure (MRCs). MRCm was more abundant than MRCs. After subchronic exposure, there was no change in plasma osmolality, ionic balance and enzyme activities. Total gill MRC density increased in the filament epithelium and renal tubules. In the gills, MRC contacting water exhibited some adjustments. Total MRC and fractional surface area unchanged, but there was an increase of MRCs contacting water at gill surface after exposure to10 and 50 mg L^-1 TiO₂-NP. MRC proliferation in filament epithelium and in renal tubules as well as the increasing MRCs at gill surface may have contributed to avoid change in plasma osmolality, ionic balance and enzyme activities and suggested a cellular physiological and morphological response to restore and maintain osmotic and ionic homeostasis after subchronic exposure.

Remediation of water and wastewater by using engineered nanomaterials: A review

Nanotechnology is currently a fast-rising socioeconomic and political knowledge-based technology owing to the unique characteristics of its engineered nanomaterials. This branch of technology is useful for water and wastewater remediation. Many scientists and researchers have been conducting different studies and experiments on the applications of engineered nanomaterials at the local to international level. This review mainly aims to provide a current overview of existing knowledge on engineered nanomaterials and their applications in water and wastewater remediation. Furthermore, the present risks and challenges of nanotechnology are examined.