Effects of the exposure to ultrafine particles on heart rate in a healthy population

Ambient ultrafine particle (PM0.1): Sources, characteristics, measurements and exposure implications on human health

The problem of ultrafine particles (UFPs; PM_0.1) has been prevalent since the past decades. In addition to become easily inhaled by human respiratory system due to their ultrafine diameter (<100 nm), ambient UFPs possess various physicochemical properties which make it more toxic. These properties vary based on the emission source profile. The current development of UFPs studies is hindered by the problem of expensive instruments and the inexistence of standardized measurement method. This review provides detailed insights on ambient UFPs sources, physicochemical properties, measurements, and estimation models development. Implications on health impacts due to short-term and long-term exposure of ambient UFPs are also presented alongside the development progress of potentially low-cost UFPs sensors which can be used for future UFPs studies references. Current challenge and future outlook of ambient UFPs research are also discussed in this review. Based on the review results, ambient UFPs may originate from primary and secondary sources which include anthropogenic and natural activities. In addition to that, it is confirmed from various chemical content analysis that UFPs carry heavy metals, PAHs, BCs which are toxic in its nature. Measurement of ambient UFPs may be performed through stationary and mobile methods for environmental profiling and exposure assessment purposes. UFPs PNC estimation model (LUR) developed from measurement data could be deployed to support future epidemiological study of ambient UFPs. Low-cost sensors such as bipolar ion and ionization sensor from common smoke detector device may be further developed as affordable instrument to monitor ambient UFPs. Recent studies indicate that short-term exposure of UFPs can be associated with HRV change and increased cardiopulmonary effects. On the other hand, long-term UFPs exposure have positive association with COPD, CVD, CHF, pre-term birth, asthma, and also acute myocardial infarction cases.

Ultrafine Particles Issued from Gasoline-Fuels and Biofuel Surrogates Combustion: A Comparative Study of the Physicochemical and In Vitro Toxicological Effects

Gasoline emissions contain high levels of pollutants, including particulate matter (PM), which are associated with several health outcomes. Moreover, due to the depletion of fossil fuels, biofuels represent an attractive alternative, particularly second-generation biofuels (B2G) derived from lignocellulosic biomass. Unfortunately, compared to the abundant literature on diesel and gasoline emissions, relatively few studies are devoted to alternative fuels and their health effects. This study aimed to compare the adverse effects of gasoline and B2G emissions on human bronchial epithelial cells. We characterized the emissions generated by propane combustion (CAST1), gasoline Surrogate, and B2G consisting of Surrogate blended with anisole (10%) (S+10A) or ethanol (10%) (S+10E). To study the cellular effects, BEAS-2B cells were cultured at air-liquid interface for seven days and exposed to different emissions. Cell viability, oxidative stress, inflammation, and xenobiotic metabolism were measured. mRNA expression analysis was significantly modified by the Surrogate S+10A and S+10E emissions, especially CYP1A1 and CYP1B1. Inflammation markers, IL-6 and IL-8, were mainly downregulated doubtless due to the PAHs content on PM. Overall, these results demonstrated that ultrafine particles generated from biofuels Surrogates had a toxic effect at least similar to that observed with a gasoline substitute (Surrogate), involving probably different toxicity pathways.

Human exposure to aerosol from indoor gas stove cooking and the resulting nervous system responses

Our knowledge of the effects of exposure to indoor ultrafine particles (sub-100 nm, #/cm³ ) on human brain activity is very limited. The effects of cooking ultrafine particles (UFP) on healthy adults were assessed using an electroencephalograph (EEGs) for brain response. Peak ultrafine particle concentrations were approximately 3 × 10⁵ particle/cm^3, and the average level was 1.64 × 10⁵ particle/cm³ . The average particle number emission rate (S) and the average number decay rate (a+k) for chicken frying in brain experiments were calculated to be 2.82 × 10¹² (SD = 1.83 × 10¹² , R²  = 0.91, p = 0.0013) particles/min, 0.47 (SD = 0.30, R²  = 0.90, p < 0.0001) min^-1 , respectively. EEGs were recorded before and during cooking (14 min) and 30 min after the cooking sessions. The brain fast-wave band (beta) decreased during exposure, similar to people with neurodegenerative diseases. It subsequently increased to its pre-exposure condition for 70% of the study participants after 30 min. The brain slow-wave band to fast-wave band ratio (theta/beta ratio) increased during and after exposure, similar to observed behavior in early-stage Alzheimer's disease (AD) patients. The brain then tended to return to its normal condition within 30 min following the exposure. This study suggests that chronically exposed people to high concentrations of cooking aerosol might progress toward AD.

Taurine reduction associated with heart dysfunction after real-world PM2.5 exposure in aged mice

Ambient PM_2.5 has been proved to be an independent risk factor for cardiovascular diseases; however, little information is available on the age-dependent effects of PM_2.5 on the cardiovascular system and the underlying mechanisms following chronic exposure. In this study, multi-aged mice were exposed to PM_2.5 via the newly developed real-ambient PM_2.5 exposure system to investigate age-related effects on the heart after long-term exposure. First, the chemical and physical properties of PM_2.5 used in the exposure system were analyzed. The heart rate of conscious mice was recorded, and results showed that exposure of aged mice to PM_2.5 for 26 weeks significantly increased heart rate. Histological analysis and ELISA assays indicated that aged mice were more sensitive to PM_2.5 exposure in terms of inducing cardiac oxidative stress and inflammation. Furthermore, untargeted metabolomics revealed that taurine was involved with the PM_2.5-induced cardiac dysfunction. The reduced taurine concentration in the heart was examined by LC-MS and imaging mass spectrometry; it may be due to the increased p53 expression level, ROS and inflammatory cytokines. These results emphasize the age-dependent effects of PM_2.5 on the cardiovascular system and suggest that taurine may be the novel cardiac effect target for PM_2.5-induced heart dysfunction in the aged.

Response of the Cardiac Autonomic Control to Exposure to Nanoparticles and Noise: A Cross-Sectional Study of Airport Ground Staff

Airport activity causes the emission of particulate matter and noise, two environmental contaminants and potential health hazards, particularly for the personnel operating nearby taxiways. We explored the association between exposure to fine/ultrafine particles (UFPs) and noise with heart rate variability (HRV), an early indicator of cardiovascular autonomic response, among a sample of airport ground staff. Between May and June 2018, thirty-four male operators (mean age = 43 years and SD = 6.7) underwent personal monitoring of exposure to nanoparticles and noise, and HRV during their work activity. We conducted univariate and multivariate analysis to test the effect of UFP and noise exposure HRV. Total Lung Deposition Surface Area (LDSA) was significantly associated with a decrease in HRV Total Power and Triangular index (β = -0.038 p = 0.016 and β = -7.8 × 10-5, p = 0.042, respectively). Noise peak level showed an opposite effect, which was significant for Total Power (β = 153.03, p = 0.027), and for Triangular index (β = 0.362, p = 0.035). Further investigation is warranted to clarify the effect of the concurrent exposure to UFPs and noise on early changes of cardiac autonomic regulation.

Daily submicron particle doses received by populations living in different low- and middle-income countries

In the present study, the daily dose in terms of particle surface area received by citizens living in different low- and middle-income countries, characterized by different lifestyles, habits, and climates, was evaluated. The level of exposure to submicron particles and the dose received by the populations of Accra (Ghana), Cairo (Egypt), Florianopolis (Brazil), and Nur-Sultan (Kazakhstan) were analyzed. A direct exposure assessment approach was adopted to measure the submicron particle concentration levels of volunteers at a personal scale during their daily activities. Non-smoking adult volunteers performing non-industrial jobs were considered. Exposure data were combined with time-activity pattern data (characteristic of each population) and the inhalation rates to estimate the daily dose in terms of particle surface area. The received dose of the populations under investigation varied from 450 mm² (Florianopolis, Brazil) to 1300 mm² (Cairo, Egypt). This work highlights the different contributions of the microenvironments to the daily dose with respect to high-income western populations. It was evident that the contribution of the Cooking & Eating microenvironment to the total exposure (which was previously proven to be one of the main exposure routes for western populations) was only 8%-14% for low- and middle-income populations. In contrast, significant contributions were estimated for Outdoor day and Transport microenvironments (up to 20% for Cairo, Egypt) and the Sleeping & Resting microenvironment (up to 28% for Accra, Ghana), highlighting the effects of different site-specific lifestyles (e.g. time-activity patterns), habits, socioeconomic conditions, climates, and outdoor air quality.

The impact on heart rate and blood pressure following exposure to ultrafine particles from cooking using an electric stove

Cooking is a major source of indoor particulate matter (PM), especially ultrafine particles (UFPs). Long-term exposure to fine and ultrafine particles (UFPs) has been associated with adverse human health effects. Toxicological studies have demonstrated that exposure to PM_2.5 (particles with aerodynamic diameter smaller than 2.5 μm) may result in increased blood pressure (BP). Some clinical studies have shown that acute exposure to PM_2.5 causes changes in systolic (SBP) and diastolic blood pressure (DBP), depending on the source of particles. Studies assessing the effect of exposure to cooking PM on BP and heart rate (HR) using electric or gas stoves are not well represented in the literature. The aim of this investigation was to perform controlled studies to quantify the exposure of 50 healthy volunteer participants to fine and ultrafine particles emitted from a low-emissions recipe for frying ground beef on an electric stove. The BP and heart rate (HR) of the volunteers were monitored during exposure and after the exposure (2 h post-exposure). Maximum UFP and PM_2.5 concentrations were 6.5 × 10⁴ particles/cm³ and 0.017 mg/m³, respectively. Exposure to UFPs from frying was associated with statistically significant increases in the SBP. The lack of food and drink during the 2 h post-cooking period was also associated with a statistically significant reduction in SBP. No statistically significant changes in DBP were observed. Physiological factors, including heat stress over the stove, movements and anxiety, could be responsible for an elevation in HR at the early stages of the experiments with a subsequent drop in HR after 90 min post-cooking, when study participants were relaxed in a living room.

Influence of methodology on the estimation of the particle surface area dose received by a population in all-day activities

In everyday life, people are exposed to different concentrations of airborne particles depending on the microenvironment where they perform their different activities. Such exposure can lead to high sub-micron particle doses. The received dose depends on particle concentration to which people are exposed (typically expressed in terms of number or surface area), time spent in each activity or microenvironment (time activity pattern) and amount of air inhaled (inhalation rate). To estimate an actual value of the received dose, all these parameters should be measured under real-life conditions; in fact, the concentrations should be measured on a personal scale (i.e. through a direct exposure assessment), whereas time activity patterns and inhalation rates specific to the activity performed should be considered. The difficulties in obtaining direct measurements of these parameters usually lead to adopt time activity patterns and inhalation rates already available in scientific literature for typical populations, and local outdoor particle concentrations measured with fixed monitoring stations and extrapolated for all the other microenvironments. To overcome these limitations, we propose a full-field method for estimating the received dose of a population sample, in which all the parameters (concentration levels, time activity patterns and inhalation rates) are measured under real-life conditions (also including the inhalation rates, that were evaluated on the basis of the measured heart rates). Specifically, 34 volunteers were continuously monitored for seven days and the data of sub-micron particle concentrations, activities performed, and inhalation rates were recorded. The received dose was calculated with the proposed method and compared with those obtained from different simplified methodologies that consider typical data of particle concentrations, time activity patterns and inhalation rates obtained from literature. The results show that, depending on the methodology used, the differences in the received daily dose can be significant, with a general underestimation of the most simplified method.

Personal black carbon and ultrafine particles exposures among high school students in urban China

Air pollution is a major public health challenge in the highly urbanized megacities of China. However, knowledge on exposure to ambient unregulated air pollutants such as black carbon (BC) and ultrafine particles (UFP) among the Chinese population, especially among urban high school students who may have highly variable time-activity patterns, is scarce. To address this, the personal exposures to BC and UFP of high school students (aged 17 to 18) in Chengdu, China were measured at 1-min intervals via portable samplers. Monitoring lasted for 2 consecutive 24-h periods with days classified as "school days" or "non-school days". Time-activity diaries and measurements were combined to explore spatial, temporal, and behavioral factors that contribute to different exposure profiles. The overall geometric means of BC and UFP were 3.60 μg/m³ and 1.83 × 10⁴p/cm³, respectively with notable spatiotemporal variation in exposures observed. In general, the household and transport microenvironments were the predominant contributors to total BC (74.5%) and UFP (36.5%) exposure. However, the outdoor public microenvironment was found to have significantly higher overall average levels of BC than the household and transport microenvironments (p < 0.001) while also presenting the greatest exposure dose intensity (EDI - a measure of exposure in a microenvironment in proportion to time spent in that environment) of 4.79. The largest overall average level of UFP occurred in the indoor public microenvironment followed by transport. The outdoor public microenvironment also presented the greatest EDI of UFP (4.17). This study shows notable spatiotemporal variety in exposure patterns and will inform future exposure and population health studies. The high EDI outdoors may mean that health positive activities, such as exercise, may be being undermined by ambient pollution.

Exposure to Submicron Particles and Estimation of the Dose Received by Children in School and Non-School Environments

In the present study, the daily dose in terms of submicron particle surface area received by children attending schools located in three different areas (rural, suburban, and urban), characterized by different outdoor concentrations, was evaluated. For this purpose, the exposure to submicron particle concentration levels of the children were measured through a direct exposure assessment approach. In particular, measurements of particle number and lung-deposited surface area concentrations at “personal scale” of 60 children were performed through a handheld particle counter to obtain exposure data in the different microenvironments they resided. Such data were combined with the time–activity pattern data, characteristics of each child, and inhalation rates (related to the activity performed) to obtain the total daily dose in terms of particle surface area. The highest daily dose was estimated for children attending the schools located in the urban and suburban areas (>1000 mm2), whereas the lowest value was estimated for children attending the school located in a rural area (646 mm2). Non-school indoor environments were recognized as the most influential in terms of children’s exposure and, thus, of received dose (>70%), whereas school environments contribute not significantly to the children daily dose, with dose fractions of 15–19% for schools located in urban and suburban areas and just 6% for the rural one. Therefore, the study clearly demonstrates that, whatever the school location, the children daily dose cannot be determined on the basis of the exposures in outdoor or school environments, but a direct assessment able to investigate the exposure of children during indoor environment is essential.

Effect of ventilation strategies and air purifiers on the children's exposure to airborne particles and gaseous pollutants in school gyms

Indoor school gyms are environments characterized by high concentrations of different airborne particulate and gaseous pollutants. In particular, like other naturally-ventilated school environments, in addition to indoor pollutants children can be exposed to sub-micron particles and gaseous pollutants emitted by outdoor sources and penetrating the building envelope; moreover, high concentrations of super-micron particles can be reached due to the resuspension phenomena related to the physical activity performed therein. The present paper aims to evaluate the effect of different ventilation methods (natural ventilation, manual airing) and the use of air purifiers in reducing the indoor concentrations of different airborne particles and gaseous pollutants in school gyms. To this end, an experimental campaign was performed in two naturally-ventilated school gyms in Barcelona (Spain) of different volumes and different distance to major urban roads. Indoor and outdoor measurements of particle number, black carbon and PM_1-10 concentrations were performed as well as indoor measurements of CO₂ and NO₂ concentrations. The study revealed that the use of air purifiers with windows kept closed (natural ventilation) can lead to a significant reduction in terms of indoor-to-outdoor concentration ratios. In the smaller gym (air changes per hour of the purifiers, ACH, equal to 9.2 h^-1) the I/O ratios were reduced by 93% and 95% in terms of particle number and PM_1-10, respectively; whereas in the larger school gym (ACH = 1.7 h^-1) the corresponding reductions were 70% and 84%. For manual airing scenarios, the effect of the air purifiers on outdoor-generated sub-micron particles is reduced; in particular, for low ACH values (i.e. ACH = 1.7 h^-1), the reduction is quite negligible (6%).

Application of a Quartz Crystal Microbalance to Measure the Mass Concentration of Combustion Particle Suspensions

Researchers studying the biological effects of combustion particles typically rely on suspending particles in de-ionized (DI) water, buffer, and/or media prior to in vitro or in vivo experiments. However, the hydrophobic nature of combustion particles makes it difficult to obtain well-suspended, evenly dispersed mixtures, which also makes it difficult to obtain equivalent dosing and endpoint comparisons. This study explored the use of a quartz crystal microbalance (QCM) to measure the mass concentration of combustion particle suspensions. It compared the QCM mass concentration to that estimated by placing a known mass of combustion particles in DI water. It also evaluated the effect of drop volume and combustion particle type on QCM measurements. The results showed that QCM is a promising direct method for measuring suspended combustion particle mass concentrations, and it is particularly effective for quantifying concentrations of difficult-to-suspend particles and for combustion particles placed in polystyrene containers, which can lead to substantial particle losses.