A novel composite hydrogel for solar evaporation enhancement at air-water interface

Recent Advances of Bio-Based Hydrogel Derived Interfacial Evaporator for Sustainable Water and Collaborative Energy Storage Applications

Solar interfacial evaporation strategy (SIES) has shown great potential to deal with water scarcity and energy crisis. Biobased hydrogel derived interfacial evaporator can realize efficient evaporation due to the unique structure- properties relationship. As such, increasing studies have focused on water treatment or even potential accompanying advanced energy storage applications with respect of efficiency and mechanism of bio-based hydrogel derived interfacial evaporation from microscale to molecular scale. In this review, the interrelationship between efficient interfacial evaporator and bio-based hydrogel is first presented. Then, special attention is paid on the inherent molecular characteristics of the biopolymer related to the up-to-date studies of promising biopolymers derived interfacial evaporator with the objective to showcase the unique superiority of biopolymer. In addition, the applications of the bio-based hydrogels are highlighted concerning the aspects including water desalination, water decontamination atmospheric water harvesting, energy storage and conversion. Finally, the challenges and future perspectives are given to unveil the bottleneck of the biobased hydrogel derived SIES in sustainable water and other energy storage applications.

Hofmeister Effect-Assisted Facile Fabrication of Self-Assembled Poly(Vinyl Alcohol)/Graphite Composite Sponge-Like Hydrogel for Solar Steam Generation

The use of hydrogel-based interfacial solar evaporators for desalination is a green, sustainable, and extremely concerned freshwater acquisition strategy. However, developing evaporators that are easy to manufacture, cheap, and have excellent porous structures still remains a considerable challenge. This work proposes a novel strategy for preparing a self-assembling sponge-like poly(vinyl alcohol)/graphite composite hydrogel based on the Hofmeister effect for the first time. The sponge-like hydrogel interfacial solar evaporator (PGCNG) is successfully obtained after combining with graphite. The whole process is environmental-friendly and of low-carbon free of freezing process. The PGCNG can be conventionally dried and stored. PGCNG shows impressive water storage performance and water transmission capacity, excellent steam generation performance and salt resistance. PGCNG has a high evaporation rate of 3.5 kg m-2 h-1 under 1 kW m-2 h-1 solar irradiation and PGCNG demonstrates stable evaporation performance over both 10 h of continuous brine evaporation and 30 cycles of brine evaporation. Its excellent performance and simple, scalable preparation strategy make it a valuable material for practical interface solar seawater desalination devices.

Superabsorbent ZnO/rubber-based hydrogel composite for removal and photocatalytic degradation of methylene blue

A superabsorbent hydrogel was prepared by the free-radical copolymerization of natural rubber (NR) latex with poly(acrylic acid) (PAA) at NR loadings up to 50 wt%. An NR/PAA hydrogel containing 40 wt% of NR (NR-40) had a water absorption capacity of 214 g/g (21,400 %) of its dry weight. The compressive modulus increased 512 % and sample integrity was improved due to the physical entanglement of NR chains. NR-40 hydrogel removed 97 % of methylene blue (MB) from the aqueous solution in 1 h (at initial concentrations of 10-1000 mg/L) and produced a maximum removal of 1191 mg MB/g of hydrogel at an initial MB concentration of 4500 mg/L. The adsorption of MB was an endothermic process. Fourier transform infrared spectroscopy indicated that hydrogen bonding and electrostatic interaction drove the process. After the in-situ incorporation of ZnO into NR-40, absorbed energy from sunlight generated active species that could photocatalytically degrade adsorbed MB in the hydrogel matrix. The scavenger tests indicated that superoxide radical anions and hydroxyl radicals were the main species for this process. The hydrogel composite material showed good stability and could be regenerated and reused over 10 cycles, degrading >80 % of the adsorbed dye. This novel natural-based hydrogel provides double functions of adsorption and photodegradation of toxic dyes without the requirement of chemicals and a separation process.

Recent Advances in High-Rate Solar-Driven Interfacial Evaporation

Recent advances in solar-driven interfacial evaporation (SDIE) have led to high evaporation rates that open promising avenues for practical utilization in freshwater production and industrial application for pollutant and nutrient concentration, and resource recovery. Breakthroughs in overcoming the theoretical limitation of 2D interfacial evaporation have allowed for developing systems with high evaporation rates. This study presents a comprehensive review of various evaporator designs that have achieved pure evaporation rates beyond 4 kg m-2 h-1, including structural and material designs allowing for rapid evaporation, passive 3D designs, and systems coupled with alternative energy sources of wind and joule heating. The operational mechanisms for each design are outlined together with discussion on the current benefits and areas for improvement. The overarching challenges encountered by SDIE concerning the feasibility of direct integration into contemporary practical settings are assessed, and issues relating to sustaining elevated evaporation rates under diverse environmental conditions are addressed.

Highly porous hydrogels for efficient solar water evaporation

Solar energy is a plentiful renewable resource on Earth, with versatile applications in both domestic and industrial settings, particularly in solar steam generation (SSG). However, current SSG processes encounter challenges such as low efficiency and the requirement for extremely high concentrations of solar irradiation. Interfacial evaporation technology has emerged as a solution to these issues, offering improved solar performance compared to conventional SSG processes. Nonetheless, its implementation introduces additional complexities and costs to system construction. In this study, we present the development of hydrophilic, three-dimensional network-structured hydrogels with high porosity and swelling ratio using a facile fabrication technique. We systematically varied the mixing ratios of four key ingredients (polyethylene glycol diacrylate, PEGDA; polyethylene glycol methyl-ether acrylate, PEGMA; phosphate-buffered saline, PBS; and 2-hydroxy-2-methylpropiophenone, PI) to control the mean pore size and swelling ratio of the hydrogel. Additionally, plasmonic gold nanoparticles were incorporated into the hydrogel using a novel methodology to enhance solar light absorption and subsequent evaporation efficiency. The resulting material exhibited a remarkable solar efficiency of 77% and an evaporation rate of 1.6 kg m-2 h-1 under standard solar illumination (one sun), comparable to those of state-of-the-art SSG devices. This high efficiency can be attributed to the synergistic effects of the hydrogel's unique composition and nanoparticle concentration. These findings offer a promising avenue for the development of highly efficient solar-powered evaporation applications.

A PAM hydrogel surface-coated hydroponic bamboo evaporator with efficient thermal utilization for solar evaporation

Solar-driven interfacial water purification emerges as a sustainable technology for seawater desalination and wastewater treatment to address the challenge of water scarcity. Currently, the energy losses via radiation and convection to surrounding environment minimize its energy efficiency. Therefore, it is necessary to develop strategies to minimize the heat losses for efficient water purification. Here, a novel evaporator was developed through the in situ gelation of PAM hydrogel on the surface carbonized hydroponic bamboo (PSC) to promote energy efficiency. The inherent porous and layered network structures of bamboo, in synergy with the functional hydration capacity of PAM hydrogel, facilitated adequate water transportation, while reducing evaporation enthalpy. The PAM hydrogel firmly covered on the photothermal layer surface effectively minimized the radiation and convection heat losses, while further harvesting those thermal energy that would otherwise dissipate into the surrounding environment. The reduced thermal conductivity of PSC served as a thermal insulator as well, obstructing heat transfer to bulk water and thus diminishing conduction losses. Consequently, the rational designed PSC could efficiently convert solar energy to purified water, leading to the evaporation of 2.09 kg m-2 h-1, the energy efficiency of 87.6 % under one sun irradiation, and yielding 9.6 kg m-2 fresh water over 11 h outdoor operation. Moreover, the PSC also performs excellent salt rejection, and long-term stability at outdoor experiment. These results demonstrated high and stable solar evaporation performance could be achieved if turning heat losses into a way of extra energy extraction to further enhance the evaporation performance. This strategy appears to be a promising strategy for effective thermal energy management and practical application.

Solar-powered simultaneous highly efficient seawater desalination and highly specific target extraction with smart DNA hydrogels

Obtaining freshwater and important minerals from seawater with solar power facilitates the sustainable development of human society. Hydrogels have demonstrated great solar-powered water evaporation potential, but highly efficient and specific target extraction remains to be expanded. Here, we report the simultaneous highly efficient seawater desalination and specific extraction of uranium with smart DNA hydrogels. The DNA hydrogel greatly promoted the evaporation of water, with the water evaporation rate reached a high level of 3.54 kilograms per square meter per hour (1 kilowatt per square meter). Simultaneously, uranyl-specific DNA hydrogel exhibited a high capture capacity of 5.7 milligrams per gram for uranium from natural seawater due to the rapid ion transport driven by the solar powered interfacial evaporation and the high selectivity (10.4 times over vanadium). With programmable functions and easy-to-use devices, the system is expected to play a role in future seawater treatment.

Tough, durable and saline-tolerant CNT@Gel-nacre nanocomposite for interfacial solar steam generation

Solar-driven interfacial evaporation materials based on nanocomposite hydrogels have emerged for seawater desalination. Nevertheless, the issue of mechanical degradation derived from the swelling behavior of hydrogel is often seriously underestimated, which strongly hinders the practical application for long-term solar vapor generation, especially in high-salinity brine. Herein, a novel CNT@Gel-nacre with enhanced capillary pumping design has been proposed and fabricated for tough and durable solar-driven evaporator through uniformly doping carbon nanotubes (CNTs) into the tough gel-nacre. Particularly, the salting out process gives rise to volume shrinkage and phase separation of polymer chains, endowing the nanocomposite hydrogel with significantly enhanced mechanical properties while simultaneously rendering more compact microchannels for water transportation, boosting the capillary pumping. Based on this unique design, the gel-nacre nanocomposite exhibits outstanding mechanical performances (13.41 MPa strength, 55.60 MJ m-3 toughness), especially mechanical durability in high salinity brine for long-term service. Furthermore, excellent water evaporation rate of 1.31 kg m-2h-1 and conversion efficiency of 93.5% in 3.5 wt% sodium chloride solution, as well as stable cycling without salt accumulation can be achieved. This work demonstrates an effective strategy for achieving solar-driven evaporator with superior mechanical properties and durability even in brine environment, showing huge potentials in long-term seawater desalination.

Fabrication of ATP/PEG/MnO2NWs composite for solar steam generation with high conversion efficiency

Solar steam generation is widely used in seawater desalination because of its high efficiency and environmental protection. However, using low-cost materials to produce efficient solar evaporators is a severe challenge. In this study, a porous carbon material was prepared by combining Attapulgite (ATP), Polyethylene glycol (PEG) and Manganese dioxide nanowires (MnO₂NWs) composite, through freeze-drying and high-temperature carbonization. The prepared CAPM aerogel shows a three-dimensional porous structure, which has high evaporation properties in pure water and simulated seawater. Under 1 sun simulated illumination, the pure water evaporation is 1.4574 kg m^-2h^-1 and the corresponding energy conversion efficiency is 85.94%. The prepared CAPM aerogel showed excellent durability and salt tolerance in 20%Nacl solution, indicating that the CAPM has excellent desalinization performance. In addition, CAPM aerogel has and exhibits super hydrophilic properties, which can transfer water molecules quickly. Due to the advantages of low cost, simple preparation method, and high solar energy conversion efficiency, the CAPM has excellent potential as a photothermal material for solar energy generation.

Optical-Concentrating Solar Distillation Based on Three-Dimensional Copper Foam Cubes Coated with CuS Nanoparticles and Agarose Gel

Solar distillation by interfacial evaporation is a promising method for relieving the freshwater crisis. However, the solar-to-water generation rate inside an enclosed system is usually lower than the solar-to-vapor evaporation rate in an open system due to the lower mass transfer rate. In this work, we demonstrate high rate solar distillation based on a three-dimensional copper foam (CF) cube, which offers five surfaces for absorbing direct and reflected sunlight to achieve optical concentration. The CF surface was first oxidized into black CuO and then dip-coated with a mixture of CuS nanoparticles (CuSNPs) and agarose gel (AG) for enhancing near-infrared (NIR) absorption and water transport. The open interconnected pores within the CF cube provide a large surface area for evaporation and steam escape. In an open space, the CuSNPs/AG-coated oxidized CF cube with the five surfaces illuminated by sunlight can achieve the solar-to-vapor evaporation rate equal to 5.83 kg m^-2 h^-1. When the same CF cube was placed in an enclosed distillation chamber with the five chamber surfaces illuminated by sunlight, the solar-to-water generation rate is equal to 4.14 kg m^-2 h^-1, which is 5.34 times higher than the case with only the top chamber surface illuminated. Lastly, when real seawater was used for distillation, although the solar-to-water generation rate was decreased by about 30%, the distillation efficiency was consistent after repeated cycles and no obvious salt accumulation was observed on the light absorbing surface. This work presents an efficient and reliable method of optical concentration for enhancing the solar distillation rate in an enclosed system.

R S, Lim HW, Lee SJ. Conversion of Hazardous Diesel Soot Particles into a Novel Highly Efficient 3D Hydrogel for Solar Desalination and Wastewater Purification

Diesel particulate matter (DPM) generated as vehicular exhaust is one of the main sources of atmospheric soot. These soot particles have been known to cause adverse health problems in humans and cause acute environmental problems. Despite great efforts for minimizing soot production, research on the disposal and recycling of inevitable diesel soot is scarce. However, DPM consists mainly of carbonaceous soot (DS) that can be easily utilized as a photothermal material for solar desalination. Recently, interfacial solar steam generation using three-dimensional (3D) structures has gained extensive attention. 3D-structured hydrogels have exhibited incredible performance in solar desalination owing to their tunable physicochemical properties, hydrophilicity, intrinsic heat localization, and excellent water transport capability. Herein, a novel DS-incorporated 3D polyvinyl alcohol (PVA)-based hydrogel is proposed for highly efficient solar desalination. The polymer network incorporated with purified DS (DSH) achieved an excellent evaporation rate of 3.01 kg m-2 h-1 under 1 sun illumination due to its vertically aligned water channels, hydrophilicity, and intrinsic porous structure. In addition, the DSH-PVA hydrogel could generate desalinated water efficiently (2.5 kg m-2 h-1) with anti-salt fouling properties. The present results would motivate the utilization and recycling of waste materials like DS as photothermal materials for efficient, low-cost, and sustainable solar desalination.

Highly Efficient and Salt-Rejecting Poly(vinyl alcohol) Hydrogels with Excellent Mechanical Strength for Solar Desalination

Interfacial solar steam generation (ISSG)-based solar desalination has recently emerged as a promising solution to tackle the global issue of fresh water scarcity. However, the energy-intensive process of conventional vapor generation techniques limits its practical applications. Hydrogels with three-dimensional (3D) structures have been reported to alleviate this energy demand, but their applications in sustainable solar desalination are hindered by their poor mechanical stability. Herein, we propose a 3D poly(vinyl alcohol) (PVA)-based hydrogel with excellent mechanical strength for effective solar desalination. The dual polymer network hydrogel (PVA-agar) incorporated with multi-walled carbon nanotubes (MWCNTs) achieved a noticeable evaporation rate of 3.1 kg m^-2 h^-1 under 1 sun irradiation, owing to its broadband light absorption, intrinsic water channels, and microporous structure that help reduce the latent heat of vaporization. More importantly, the application of kosmotropic ammonium sulfate ions was found to greatly improve the mechanical strength of the hydrogels using a facile Hofmeister-assisted soaking method. Finally, the PVA-agar-MWCNT hydrogel was able to desalinate seawater efficiently (2.5 kg m^-2 h^-1) with self-cleaning capability of salt crystals. The salinity level of the desalinated water was also comparable to drinking clean water. The present results would pave the way for fabricating mechanically strong, hydrophilic, and highly efficient hydrogels for effective and sustainable solar desalination.

Quantifying the trade-off between stiffness and permeability in hydrogels

Hydrogels have a distinct combination of mechanical and water-transport behaviors. As hydrogels stiffen when they de-swell, they become less permeable. Here, we combine de Gennes' semi-dilute polymer theory with the Kozeny-Carman equation to develop a simple, succinct scaling law describing the relationship between mechanical stiffness and hydraulic permeability where permeability scales with stiffness to the -8/9 power. We find a remarkably close agreement between the scaling law and experimental results across four different polymer families with varied crosslinkings. This inverse relationship establishes a fundamental trade-off between permeability and stiffness.

Hybrid nanofibrous aerogels for all-in-one solar-driven interfacial evaporation

Solar-driven interfacial evaporation is an emerging technology to obtain fresh water using solar energy. However, the complicated system and the corresponding fabrication process severely restrict its large-scale and cost-effective production. Herein, an all-in-one solar-driven interfacial evaporator was fabricated via a hybrid nanofibrous aerogel of aramid nanofibers (ANFs), carbon nanotubes (CNTs), and gold nanoparticles (AuNPs). Assisted by the reprotonation of the ANFs, CNTs are assembled into the nanofibrous network for through-body light-to-heat activity, and AuNPs are set on the surface layer to enhance solar absorption. The aerogel also features low thermal conductivity to suppress heat losses and high capillary action to wick and confine water within the aerogels. Benefitting from the synergistic effect, the aerogel shows a high evaporation rate of 1.53 kg m^-2h^-1 and an evaporation efficiency of 91.3% under 1 sun irradiation. Simultaneously, the evaporator demonstrates high purification capacity for wastewaters with dyes and heavy metal ions. The integrated structure design and facile fabrication process would make the hybrid nanofibrous aerogel-based all-in-one evaporators promising for cost-effective and large-scale application under ambient solar irradiance.

Magnetic nanostructure and biomolecule synergistically promoted Suaeda-inspired self-healing hydrogel composite for seawater evaporation

Multifunctional hydrogels with excellent comprehensive performance are essential prerequisite for the implementation of effective water resources technology with high efficiency and low energy consumption. Inspired by the water purification and self-healing properties of natural plants, and based on the synergy of photothermal and biological effects, high photothermal Fe₃O₄ nanoparticles and natural polyhydroxy oligomeric proanthocyanidin (OPC) are introduced into a water-active polyvinyl alcohol (PVA) hydrogel. Two new bio-hydrogels of PVA/Fe₃O₄/graphite and PVA/OPC with self-healing and stretchable properties are proposed and designed. The obtained hydrogels exhibit reversible covalent cross-linked water-promoted healing (chemically) and photothermal melting/recrystallization healing (physically). The double-layered hydrogel composite demonstrates a dual response function (sunlight and near-infrared light), along with water purification properties. It is prepared through a water spray triggered self-healing process. The ultimate fracture strain of the photothermal layer and purification layer hydrogel was more than 1000% and 400% respectively after self-healing.After 48 h of hydrogel composite adsorption, the color of a methylene blue solution faded, and the absorption peak at 664 nm decreased. In addition, this research adopts a phased evaporation method to concentrate local energy and provide power for seawater evaporation. The evaporation efficiency of seawater induced by near-infrared (NIR) light was up to 3.15 kg m^-2 h^-1, whereas that under sunlight was 1.25 kg m^-2 h^-1. Selection of the evaporation excitation light source allowed control of the evaporation efficiency. The proposed technology is expected to be widely applicable to the staged evaporation of seawater as well as water purification.

An anti-oil-fouling superhydrophilic composite aerogel for solar saline alkali water desalination

An anti-oil-fouling superhydrophilic composite aerogel (ASG) with a rough surface and macroporous structure is prepared for the solar desalination of oil-in-water emulsion and saline alkali water.

Reduced Red Mud as the Solar Absorber for Solar-Driven Water Evaporation and Vapor-Electricity Generation

The emergent solar-driven water evaporation technology provides a reassuring scheme for red mud (RM) utilization in environment and materials science. With fewer restrictions on raw materials, wide availability of sheer quantity, and high complexity in chemical composition, the RM may be a promising candidate for solar absorbers. Here, we developed a novel solar absorber with reduced RM. It features favorable light absorption and photothermal conversion ability using biomass pyrolysis. When added to the polyvinyl alcohol and chitosan gel substrate, the light absorptance can reach 94.65%, while the corresponding evaporation rate is as high as 2.185 kg m^-2 h^-1 under an illumination density of 1 kW m^-2. We further demonstrated its potential as an efficient solar absorber in the solar-driven water evaporation and the thermoelectric device to realize the stable and efficient coproduction of vapor and electricity.

A novel photothermal, self-healing and anti-reflection water evaporation membrane

For the solar water evaporation system, there are no reports on the self-healing support, which is crucial for the sustainable use of solar evaporation membrane. In this work, a self-healing hydrogel is prepared via free radical copolymerization with covalent cross-linking and coordination cross-linking and is used as a photothermal water evaporation support. The photothermal material is then introduced into the hydrogel by physically doping acetylene carbon black. At the same time, inverted micro-pyramids are fabricated on the surface of the hydrogel by soft imprint to increase the utilization efficiency of incident light. The water evaporation rate of the composite membrane can reach 1.58 kg m-2 h-1, and the breaking elongation is 1580%. It can self-heal after it is completely broken, and can still be stretched 3 times its original length. The design of this self-healing photothermal membrane will provide a new idea for its application in a harsh outdoor environment.

A Bioinspired Elastic Hydrogel for Solar-Driven Water Purification

The global demand for clean and safe water will continue to grow well into the 21st century. Moving forward, the lack of access to clean water, which threatens human health and strains precious energy resources, will worsen as the climate changes. Therefore, future innovations that produce potable water from contaminated sources must be sustainable. Inspired by nature, a solar absorber gel (SAG) is developed to purify water from contaminated sources using only natural sunlight. The SAG is composed of an elastic thermoresponsive poly(N-isopropylacrylamide) (PNIPAm) hydrogel, a photothermal polydopamine (PDA) layer, and a sodium alginate (SA) network. Production of the SAG is facile; all processing is aqueous-based and occurs at room temperature. Remarkably, the SAG can purify water from various harmful reservoirs containing small molecules, oils, metals, and pathogens, using only sunlight. The SAG relies on solar energy to drive a hydrophilic/hydrophobic phase transformation at the lower critical solution temperature. Since the purification mechanism does not require water evaporation, an energy-intensive process, the passive solar water-purification rate is the highest reported. This discovery can be transformative in the sustainable production of clean water to improve the quality of human life.

Enhanced Steam Temperature Enabled by a Simple Three-Tier Solar Evaporation Device

Interfacial water evaporation technology by using solar energy provides one of the promising pathways for freshwater shortage management. However, current research mainly focuses on the improvement of evaporation efficiency by macro or microregulations, ignoring the steam temperature, which is a manifestation of the quality of water. Herein not only is a high-rate solar evaporation achieved but also steam temperature is enhanced by a simple three-tier (wet absorber-air gap-dry absorber) device. In a routine interfacial evaporation test, the evaporator achieves a stable evaporation rate up to 2.15 kg m-2 h-1 under one sun, demonstrating a competitive evaporation rate compared with other reports. With the three-tier device, the steam temperature can increase 33.7%, 41.13%, and 47% without dry absorber under one sun, two sun, and three sun illumination, respectively. At the same time, the steam temperature can be as high as 95.5 °C under three sun intensities. This work provides the possibility of using a simple three-tier device for high-temperature steam generation without extra energy input, which contributes to an idea for future research on the production high-quality water.

High-efficiency solar evaporator prepared by one-step carbon nanotubes loading on cotton fabric toward water purification

Solar-driven photothermal conversion devices are proved to promising in fresh water generation, but often hindered due to complex manufacturing processes, low efficiency and poor reusability. Herein, we proposed a one-step carboxylated multi-walled carbon nanotube (MWCNTs-COOH) loading on the cotton fabric (CF), and assembled a jellyfish-shaped solar evaporator in which the evaporation layer acted as the body and cotton yarns (CYs) as the tentacles used for water transportation. The jellyfish-shaped solar evaporator has the advantages of separating the evaporation layer from bulk water, thereby effectively prevents heat dissipation and improves evaporation efficiency. The assembled evaporator exhibited an evaporation rate of 1.18kgm^-2h^-1 and a high energy conversion efficiency of 86.01% under 1.0 sun illumination (1.0kWm^-2). This simple preparation, high efficiency and excellent reusability jellyfish-shaped solar evaporator is expected to be used efficiently under natural light conditions, and has great application prospects for remote areas that lack fresh water supplies.

Multilayer graphite nano-sheet composite hydrogel for solar desalination systems with floatability and recyclability

The application of carbon-based nanomaterials with high photothermal conversion efficiencies in solar desalination has the advantages of economy, environmental protection, availability and sustainability.