Multifunctional capacity of CoMnFe-LDH/LDO activated peroxymonosulfate for p-arsanilic acid removal and inorganic arsenic immobilization: Performance and surface-bound radical mechanism

Synergistic Oxygen Vacancy and Dual-Electron Centers for Enhancing Peroxymonosulfate Activation by Fe─Mn─Mg LDH/BC: Insights into the Key Roles of Magnesium

Enhancing singlet oxygen (1O2)-dominated nonradical oxidation with higher selectivity and longer lifetime is crucial for efficient antibiotic degradation. Herein, Fe/Mn/Mg layered double hydroxides (FeMnMg-LDH) modified rice husk biochar composites (BC/FeMMgx-LDH, x = 1, 2, and 3) are prepared to activate peroxymonosulfate (PMS) for sulfamethazine (SMT) removal. Increasing Mg content in FeMnMg-LDH enhances catalytic efficiency, achieving 99.2% SMT removal (50 mg L-1) within 30 min with BC/FeMMg3-LDH/PMS. 1O2 is identified as the primary active species, with its dominance increasing as Mg content rises. High Mg content induces lattice strain and structural disorder in LDH by atom intercalation in the octahedron, creating abundant oxygen vacancies (Vo) and surface M─OH groups. These Vo amplify the Fe─Mg polarization effect and promote the formation of electron-rich Fe centers. Simultaneously, the elevated d-band center at the Mn site develops electron-donating centers, facilitating short-range electron transfer to Vo and the electron-rich Fe center, boosting high local electron density. This process enhances PMS activation and 1O2 regulation. Moreover, the neutral pH microenvironment constructed by Mg, hydroxyl and interlayer carbonates supports stable 1O2 generation and broad pH applicability. This study offers new insights into the Mg-induced structural effects in BC/FeMMgx-LDH and the development of efficient 1O2-dominated PMS catalysts.

Iron scrap derived nano zero-valent iron/biochar activated persulfate for p-arsanilic acid decontamination with coexisting microplastics

P-arsanilic acid (AA) has received widespread attention because of its conversion to more toxic inorganic arsenic compounds (arsenate and arsenite) in the natural ecosystems. Its removal process and mechanisms with co-existence of microplastics remain unkown. In this study, biochar loaded with nano zero-valent iron (nZVI) particles (ISBC) was prepared by using iron scrap obtained from a steel works and wood chips collected from a wood processing plant. The advanced oxidation system of sodium persulfate (PDS) activated by ISBC was applied for AA degradation and inorganic arsenic control in aqueous media. More than 99% of the AA was completely degraded by the ISBC/PDS system, and the As(III) on AA was almost completely oxidized to As(V) and finally removed by ISBC. HCO3- inhibited the removal of AA by the ISBC/PDS system, while Cl- had a dual effect that showing inhibition at low concentrations yet promotion at high concentrations. The effect of microplastics on the degradation of AA by the ISBC/PDS system was further investigated due to the potential for combined microplastic and organic arsenic contamination in rural/remote areas. Microplastics were found to have little effect on AA degradation in the ISBC/PDS system, while affect the transport of inorganic arsenic generated from AA degradation. Overall, this study provides new insights and methods for efficient removal of p-arsanilic acid from water with coexisting microplastics.

Self-assembed Fe-doped tobacco straw rich in lignin biochar towards efficient activation of peroxymonosulfate for sulfonamide elimination: Characterization, experimental study, and theoretical calculation

In this study, biochars derived from different crop straws rich in lignin were prepared and used to adsorb the transition metal Fe3+ from wastewater. Among these biochars, ball-milled tobacco straw biochar (BTBC) exhibited a greater adsorption capacity. Subsequently, BTBC saturated with Fe3+ was pyrolysed to prepare self-assembled Fe-doped BTBC (Fe@BTBC), which exhibited excellent catalytic ability for peroxymonosulfate (PMS). The degradation rate of sulfadiazine (SDZ) in Fe@BTBC/PMS system was 92.4 % within 60 min. Solution pH and co-existing HCO3- and CO32- were the undeniable environmental factors influencing the degradation rate/efficiency of sulfonamides (SAs). Characterization analysis showed that abundant defects, oxygenated groups of -OH/C=O, and grafted Fe(II) on Fe@BTBC were the main catalytic sites. Surface-bound radicals and 1O2 were the primary contributors for SAs oxidation, and SO4•- and •OH were additional participants. Five degradation pathways were proposed based on intermediate authentication and density functional theory (DFT) calculations, and pathway II was speculated to be the primary pathway. In addition, the Fe@BTBC/PMS system exhibited excellent detoxification capacity for SAs, as the toxicity of the intermediates was lower than that of SAs. Additionally, the Fe@BTBC/PMS system could efficiently remove SAs from real waters, and Fe@BTBC exhibited favourable security over a wide pH range.

The morphology and structure of zero-valent iron nanosheets promote the activation of persulfate for degradation of ciprofloxacin

Herein, a biochar-supported zero-valent iron (ZVI) nanosheet catalyst (Fe@BC2-2) for the activation of persulfate to degrade ciprofloxacin (CIP) was prepared using industrial kraft lignin and Fenton sludge as carbon and iron sources, respectively. Fe@BC2-2 showed considerably better CIP degradation efficiency (96.9% at 20 mg L-1) than traditional catalysts. Furthermore, Fe@BC2-2 exhibited CIP degradation efficiency above 96% in a wide pH range (3-11) and high resistance to interference from various inorganic anions and humic acid even under real water body conditions. The Fe@BC2-2 catalyst showed good magnetic separation performance and maintained high CIP degradation efficiency (87.0%) after five degradation-regeneration cycles. CIP degradation was facilitated by ZVI nanosheets along with functional groups and defects on the surface of the biochar. As determined through radical-quenching experiments, both radical and non-radical pathways contributed to the degradation of CIP, with the non-radical pathway being dominant, especially with singlet oxygen (1O2) as the active species. The degradation pathway of CIP was inferred through the analysis of intermediate products, which showed lower toxicity than CIP. This work not only proposes a strategy for the utilization of traditional kraft pulping lignin and Fenton sludge but also presents an innovative catalyst for the degradation of antibiotics.

Promoting effect of oxygen vacancies in CuZnOx-2/peroxymonosulfate system on the p-arsanilic acid degradation and secondary arsenic species immobilization

Combining chemical oxidation and adsorption is highly desirable but challenging to remove organoarsenic compounds for water purification. Herein, we prepared a Zn-doped CuO (CuZnOx-2) catalyst by incorporating Zn atoms into the CuO lattice, which results in abundant surface oxygen vacancies (OVs) and modulates the electronic structure of Cu-OVs-Zn sites for PMS activation to degrade p-arsanilic acid (p-ASA) and adsorb the secondary arsenic species simultaneously. The elevated d-band centers for Cu upward to the Fermi level can significantly strengthen the adsorption of PMS, p-ASA, and the generated arsenic species. The OVs cause the charge redistribution to form electron-rich centers, which accelerate the electron transfer from Cu-OVs-Zn sites to adsorbed PMS, facilitating the cleavage of peroxide bond to produce SO4•-, •OH. Furthermore, the PMS adsorbed on the local environment of OVs with different configurations can directly decompose to produce 1O2 without undergoing PMS → O2•- → 1O2 or O2 → O2•- → 1O2 processes. The evolution process of the main arsenic species in solution and catalyst surface with oxidation was clarified. The ultimate removal of the total As involves 20 % As(III), 60 % As(V), and 20 % organic arsenic intermediates via forming inner-sphere complexes or electrostatic interaction. This contribution provides a brand-new perspective for the remediation of organoarsenic pollution over designing highly active catalysts.

The recent research progress in the application of the nanozyme-hydrogel composite system for drug delivery

Hydrogels, comprising 3D hydrophilic polymer networks, have emerged as promising biomaterial candidates for emulating the structure of biological tissues and delivering drugs through topical administration with good biocompatibility. Nanozymes can catalyze endogenous biomolecules, thereby initiating or inhibiting in vivo biological processes. A nanozyme-hydrogel composite inherits the biological functions of hydrogels and nanozymes, where the nanozyme serves as the catalytic core and the hydrogel forms the structural scaffold. Moreover, the composite can concentrate nanozymes in targeted lesions and catalyze the binding of a specific group of substrates, resulting in pathological microenvironment remodeling and drug-penetrating barrier impairment. The composite also shields nanozymes to prevent burst release during catalytic production and reduce related toxicity. Currently, the application of these composites has been extended to antibacterial, anti-inflammatory, anticancer, and tissue repair applications. In this review, we elucidate the preparation methods for nanozyme-hydrogel composites, provide compelling evidence of their advantages in drug delivery and provide a comprehensive overview of their biological application.

Efficiently photocatalysis activation of peroxymonosulfate by bimetallic metal-organic frameworks Mn-MIL-53(Fe) for ibuprofen degradation: Synergistic efficiency, mechanism and degradation pathways

In this study, a UV-driven photocatalytic activation of peroxymonosulfate (PMS) system was constructed using bimetallic metal-organic frameworks to degrade pharmaceuticals and personal care products (PPCPs). Mn-MIL-53(Fe) was successfully synthesised by adjusting the doping ratio of Mn using solvothermal method. The removal of ibuprofen (IBP) by UV/Mn-MIL-53(Fe)/PMS process was as high as 79.7% in 30 min with a Mn doping ratio of 1.0 (molar ratio of Mn to Fe), and the reaction rate constant was 26.9% higher than undoped. Mn-MIL-53(Fe) had been systematically characterized in terms of its physical structure, microscopic morphology, surface functional groups and photoelectric properties. The mechanism investigation revealed that the cycling of Mn and Fe accelerated the rate of electron transfer in the system, which significantly increased the activation efficacy of PMS to generate more hydroxyl and sulfate radicals for IBP degradation. A total of 13 transformation products were detected during the degradation of IBP by the UV/Mn-MIL-53(Fe)/PMS process. Theoretical calculations were used to predict the sites on the IBP molecule that were vulnerable to attack, and four possible degradation pathways were deduced. The excellent stability and efficient catalytic properties of Mn-MIL-53(Fe) provided a promising solution to the problem of water treatment contaminated with PPCPs.

Singlet oxygen dominant-activation by hollow structural cobalt-based MOF/peroxymonosulfate system for micropollutant removal

Despite the keen interest in potentially using the metal-organic framework (MOF) in advanced oxidation processes (AOPs), their application for environmental abatement and the corresponding degradation mechanisms have remained largely elusive. This study explores the use of cobalt-based MOF (CoMOF) for peroxymonosulfate (PMS) activation to remove tetracycline (TC) from water resources. Under optimal conditions, the given catalytic system could achieve a TC removal of 83.3%. Radical quenching tests and EPR analysis revealed that SO4•-, HO•, •O2-, and 1O2 could participate in the catalytic degradation, but the discernible removal mechanism was mainly ascribed to the nonradical pathway induced by 1O2. At only 5 mg/L of CoMOF, the performance of the catalytic system was superior to that of PMS alone for different types of micropollutants. The CoMOF/PMS system could also reliably deal with typical anions in water, such as Cl-, SO42-, HCO3-, and PO43-. The MOF catalyst could last for four cycles with a minor decrease in reactivity of ∼30%. However, the removal performance decreased markedly when aromatic natural organic matter (NOM) were present in the water bodies, and the effectiveness was lower in alkaline or acidic environments. Our work offers insights into the catalytic degradation of CoMOF/PMS applied in contaminated water remediation and serves as a baseline for fabricating an efficient MOF with enhanced catalytic performance and stability.

High-performance, stable CoNi LDH@Ni foam composite membrane with innovative peroxymonosulfate activation for 2,4-dichlorophenol destruction

In this study, the cobalt-nickel layered double hydroxides (CoNi LDH) were synthesized with a variety of Co/Ni mass ratio, as CoxNiy LDHs. In comparison, Co1Ni3 LDH presented the best peroxymonosulfate (PMS) activation efficiency for 2,4-dichlorophenol removal. Meanwhile, CoNi LDH@Nickel foam (CoNi LDH@NF) composite membrane was constructed for enhancing the stability of catalytic performance. Herein, CoNi LDH@NF-PMS system exerted high degradation efficiency of 99.22% within 90 min for 2,4-DCP when [PMS]0 = 0.4 g/L, Co1Ni3 LDH@NF = 2 cm × 2 cm (0.2 g/L), reaction temperature = 298 K. For the surface morphology and structure of the catalyst, it was demonstrated that the CoNi LDH@NF composite membrane possessed abundant cavity structure, good specific surface area and sufficient active sites. Importantly, ·OH, SO4·- and 1O2 played the primary role in the CoNi LDH@NF-PMS system for 2,4-DCP decomposition, which revealed the PMS activation mechanism in CoNi LDH@NF-PMS system. Hence, this study eliminated the stability and adaptability of CoNi LDH@NF composite membrane, proposing a new theoretical basis of PMS heterogeneous catalysts selection.

MXene-supported MIL-88A(Fe) as persulfate activator for removal of tetracycline

The poor conductivity, poor stability, and agglomeration of iron-based metal organic framework MIL-88A(Fe) limit its application as persulfate (PS) activator in water purification. Herein, MXene-supported MIL-88A(Fe) composites (M88A/MX) were synthesized to enhance its adsorption and catalytic capability for tetracycline (TC) removal. Scanning electron microscope (SEM), X-ray diffractometer (XRD), Fourier transform infrared spectrometer (FT-IR), and X-ray photoelectron spectroscopy (XPS) were used to characterize prepared materials, confirming the successful attachment of MIL-88A(Fe) to the surface of MXene. M88A/MX-0.2 composites, prepared with 0.2 g MXene addition, exhibit optimal degradation efficiency, reaching 98% under conditions of 0.2 g/L M88A/MX-0.2, 1.0 mM PS, 20 ppm TC, and pH 5. The degradation rate constants of M88A/MX-0.2 were 0.03217 min-1, which was much higher than that of MIL-88A(Fe) (0.00159 min-1) and MXene (0.00626 min-1). The removal effects of reaction parameters, such as dosage of M88A/MX-0.2 and PS; initial solution pH; and the presence of the common co-existing constituents (humic acid and the inorganic anions) were investigated in detail. Additionally, the reuse of M88A/MX-0.2 showed that the composites had good cycling stability by recurrent experiments. The results of electron paramagnetic resonance (EPR) and quenching experiments indicated that ·OH, ·SO4-, and ·O2- were involved in the M88A/MX-0.2/PS system where persulfate oxidation process was activated with prepared M88A/MX-0.2. In addition, the intermediates of photocatalytic degradation were determined by HPLC-MS, and the possible degradation pathways of the target molecules were inferred. This study offered a new avenue for sulfate-based degradation of Fe-based metal organic framework.

A review of the degradation of antibiotic contaminants using advanced oxidation processes: modification and application of layered double hydroxides based materials

In recent years, the treatment of organic pollutants has become a global concern due to the threat to human health posed by emerging contaminants, especially antibiotic contamination. Advanced oxidation processes (AOPs) can solve the organic pollution problem well, which have been identified as a promising solution for the treatment of hard-to-handle organic compounds including antibiotic contaminants. Layered double hydroxides (LDHs) are excellent catalysts because of their flexible tunability, favorable thermal stability, abundant active sites, and facile exchangeability of intercalated anions. This paper conducted a systematic review of LDHs-based materials used for common antibiotic removal by three significant AOP technologies, such as photocatalysis, the Fenton-like processes, and peroxymonosulfate catalysis. The degradation effects studied in various studies were reviewed, and the mechanisms were discussed in detail based on the type of AOPs. Finally, the challenges and the application trends of AOPs that may arise were prospected. The aim of this study is to suggest ways to provide practical guidance for the screening and improvement of LDH materials and the rational selection of AOPs to achieve efficient antibiotic degradation. This could lead to the development of more efficient and environmentally friendly materials and processes for degrading antibiotics, with significant implications for our ecological conservation by addressing water pollution.

Enhanced electron transfer for activation of peroxymonosulfate via MoS2 modified iron-based perovskite

The increasing use of fluoroquinolone antibiotics, which are found in various environmental media, is a constant threat to ecological safety and human health. In this paper, SrFeO3@MoS2 heterogeneous catalyst was prepared to activate peroxymonosulfate (PMS) for the degradation of levofloxacin (LVO). The characteristics of SrFeO3@MoS2 samples were studied and the optimum conditions for the removal of LVO by SrFeO3@MoS2/PMS system were investigated. The removal of LVO by the SrFeO3@MoS2-0.3/PMS system could reach 96.06% within 20 min of reaction. The effect of inorganic anions (SO42-, Cl-, NO3- and H2PO4-) commonly found in actual water bodies on catalytic reaction was explored. The reusability investigation revealed that the catalyst could still remove 88.06% of LVO within 20 min after four cycles. Moreover, SO4•-, •OH and 1O2 were identified by Electron Paramagnetic Resonance (EPR) tests and scavenger experiments, where the SO4•- and •OH were dominant reactive species. Combining with the XPS characterisation, the activation mechanism of SrFeO3@MoS2-0.3/PMS was proposed, and the oxygen vacancies and transition metals on the sample surface were active sites of PMS activation. Furthermore, the possible degradation pathways of LVO were well-established based on the detected intermediates.

Peroxymonosulfate activation by CuMn-LDH for the degradation of bisphenol A: Effect, mechanism, and pathway

The remediation of water contaminated with bisphenol A (BPA) has gained significant attention. In this study, a hydrothermal composite activator of Cu3Mn-LDH containing coexisting phases of cupric nitrate (Cu(NO3)2) and manganous nitrate (Mn(NO3)2) was synthesized. Advanced oxidation processes were employed as an effective approach for BPA degradation, utilizing Cu3Mn-LDH as the catalyst to activate peroxymonosulfate (PMS). The synthesis of the Cu3Mn-LDH material was characterized using X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), and transmission electron microscopy (TEM). According to the characterization data and screening experiments, Cu3Mn-LDH was selected as the best experimental material. Cu3Mn-LDH exhibits remarkable catalytic ability with PMS, demonstrating good degradation efficiency of BPA under neutral and alkaline conditions. With a PMS dosage of 0.25 g·L-1 and Cu3Mn-LDH dosage of 0.10 g·L-1, 10 mg·L-1 BPA (approximately 17.5 μM) can be completely degraded within 40 min, of which the TOC removal reached 95%. The reactive oxygen species present in the reaction system were analyzed by quenching experiments and EPR. Results showed that sulfate free radicals (SO4•-), hydroxyl free radicals (•OH), superoxide free radicals (•O2-), and nonfree radical mono-oxygen were generated, while mono-oxygen played a key role in degrading BPA. Cu3Mn-LDH exhibits excellent reproducibility, as it can still completely degrade BPA even after four consecutive cycles. The degradation intermediates of BPA were detected by GCMS, and the possible degradation pathways were reasonably predicted. This experiment proposes a nonradical degradation mechanism for BPA and analyzes the degradation pathways. It provides a new perspective for the treatment of organic pollutants in water.

Rapid degradation and detoxification of metronidazole using calcium sulfite activated by CoCu two-dimensional layered bimetallic hydroxides: Performance, mechanism, and degradation pathway

In this study, cobalt copper-layered double hydroxides (CoCu-LDHs) were prepared by coprecipitation as catalysts to activate CaSO3 for metronidazole (MNZ) degradation. This is the first report on layered double hydroxides activating sulfite for the degradation of organic pollutants. Meanwhile, to address the issue of self-quenching reactions readily occurring in conventional sulfite advanced oxidation systems and resulting in low oxidant efficiency, CaSO3 with slightly soluble in water was used instead of commonly used Na2SO3, to improve the limitations of traditional systems. The results showed that in the CoCu-LDHs/CaSO3 system, the degradation rate of MNZ reached 98.7% within 5 min, representing a 23.0% increase compared to the CoCu-LDHs/Na2SO3 system. Owing to the excellent catalytic performance exhibited by CoCu-LDHs, characterizations including XRD, FTIR, SEM, TEM, BET and XPS were carried out to investigate this further. The results confirmed the successful synthesis of CoCu-LDH, and the activation mechanism study revealed that Co and Cu were considered to the main elements in activating CaSO3, demonstrating good synergistic effects. In addition, the oxygen vacancies on the catalyst surface also played a positive role in generating radicals and promoting electron transfer. Subsequently, the effects of Co/Cu ratio, catalyst dosage, oxidant concentration, pollutant concentration, pH and coexisting substances on MNZ degradation were investigated. Additionally, based on the LC-MS analysis of degradation products and toxicity tests, MNZ was transformed into different intermediates with low toxicity through four pathways, eventually mineralizing into inorganic small molecules. After six cycles, the MNZ degradation rate still reached 82.1%, exhibiting excellent stability and recyclability. In general, this study provides new ideas for activating sulfite, while providing theoretical support for subsequent research on sulfite advanced oxidation system.

Improving sewage sludge dewaterability via heterogeneous activation of persulfate by Fe-Al layered double hydroxide: Role of generated SO4-•

In this study, Fe-Al layered double hydroxide (Fe-Al LDH) was prepared and applied to activate persulfate to condition sewage sludge and improve its dewaterability. The results showed that Fe-Al LDH activated persulfate to generate a large amount of free radicals, which attacked extracellular polymeric substances and reduced their content, disrupted microbial cells, released bound water, decreased sludge particle size, increased sludge zeta potential, and improved sludge dewaterability. After sewage sludge was conditioned with Fe-Al LDH (0.20 g/g total solids (TS)) and persulfate (0.10 g/g TS) for 30 min, the capillary suction time of the sludge dropped from 52.0 s to 16.3 s, while the moisture content of the sludge cake decreased from 93.2% to 68.5%. The dominant active free radical produced by the Fe-Al LDH-activated persulfate was SO₄^-•. The maximum Fe³⁺ leaching of the conditioned sludge was only 102.67 ± 4.45 mg/L, thus effectively alleviating the secondary pollution of Fe³⁺. The leaching rate of 2.37% was significantly lower than that of the sludge homogeneously activated with Fe²⁺ (738.4 ± 26.07 mg/L and 71.00%).

Catalytic oxidation activation of peroxymonosulfate over Fe-Co bimetallic oxides for flurbiprofen degradation

In this research, FeCo₂O₄ nanomaterial was successfully synthesized by a typical sol-gel method and conducted as an effective agent for peroxymonosulfate (PMS) activation to eliminate antibiotics flurbiprofen (FLU), a strong nonsteroidal drug. FeCo₂O₄ nanomaterial was characterized by XRD, TEM, SEM, and XPS. Various characterization results proved that FeCo₂O₄ held stable spinel structure. The interfering factors including initial pH, PMS concentration, catalyst dosage, inorganic anions, and humic acid on FLU removal were also discussed. The conclusion was that the removal efficiency of FLU reached 98.2% within 120 min after adding FeCo₂O₄ (0.4 g L^-1) and PMS (3 mM). The optimal pH for FLU degradation was the initial pH of 6.5; too acidic or alkaline was not conductive to the degradation. The existence of HA and Cl^- restrained the degradation of FLU, and HCO₃^- promoted the removal, while the influence of NO₃^- and SO₄^2- could not be considered. The radical scavenging experiment confirmed that ^•OH, O₂^•-, and SO₄^•- participated in FLU removal and SO₄^•- functioned a leading role. FeCo₂O₄ showed high efficiency for PMS activation in pH range of 3.0 to 10.0. After the fourth cycle operation, the FLU removal rate exceeded 76.9%, and the Co leaching rate was low during the catalytic reaction. This study shows that FeCo₂O₄ nanomaterial is an efficient and environment-friendly catalyst, which can be applied for PMS activation to remove organic pollutants in water.

Emerging Phosphate-Functionalized Co3O4/Kaolinite Composites for Enhanced Activation of Peroxymonosulfate

The Fenton-like reaction, as one of the most efficient strategies to generate radical species for the degradation of environmental pollutants, has attracted considerable attention. However, engineering low-cost catalysts with excellent activity by phosphate surface functionalization has seldom been used for the activation of peroxymonosulfate (PMS). Herein, emerging phosphate-functionalized Co₃O₄/kaolinite (P-Co₃O₄/Kaol) catalysts have been prepared by hydrothermal and phosphorization. Kaolinite nanoclay with rich hydroxyl groups plays a vital role in realizing phosphate functionalization. The results indicate that P-Co₃O₄/Kaol shows superior catalytic performance and excellent stability to the degradation of Orange II, which could be attributed to the existence of phosphate that promotes the adsorption of PMS and the electron transfer of Co²⁺/Co³⁺ cycles. Furthermore, the ^•OH radical was identified as the dominating reactive species for the degradation of Orange II compared to the SO₄^•- radical. This work could offer a novel preparation strategy for emerging functionalized nanoclay-based catalysts for effective pollutant degradation.

A Multifunctional Cascade Bioreactor Based on a Layered Double Oxides Composite Hydrogel for Synergetic Tumor Chemodynamic/Starvation/Photothermal Therapy

The field of nanomedicine-catalyzed tumor therapy has achieved a lot of progress; however, overcoming the limitations of the tumor microenvironment (TME) to achieve the desired therapeutic effect remains a major challenge. In this study, a nanocomposite hydrogel (GH@LDO) platform combining the nanozyme CoMnFe-layered double oxides (CoMnFe-LDO) and natural enzyme glucose oxidase (GOX) was engineered to remodel the TME to enhance tumor catalytic therapy. The CoMnFe-LDO is a nanozyme that can convert endogenous H₂O₂ into reactive oxygen species (ROS) and O₂ to achieve chemodynamic therapy (CDT) and alleviate the hypoxic microenvironment. Meanwhile, GOX can catalyze the conversion of glucose and O₂ to gluconic acid and H₂O₂, which not only represses the ATP production of tumor cells to achieve starvation therapy (ST), but also decreases the pH value of TME and supplies extra H₂O₂ to enhance the CDT effect. Furthermore, this well-designed CoMnFe-LDO possessed a high photothermal conversion efficiency (66.63%), which could promote the generation of ROS to enhance the CDT effect and achieve photothermal therapy (PTT) under near-infrared light irradiation. The GH@LDO hydrogel cascade reaction overcomes the limitation of the TME and achieves satisfactory CDT/ST/PTT synergetic effects in vitro and in vivo. This work provides a new strategy for remodeling the TME using nanomedicine to achieve precise tumor cascaded catalytic therapy. STATEMENT OF SIGNIFICANCE: At present, the focus of tumor therapy has begun to shift from monotherapy to combination therapy for improving the overall therapeutic effect. In this study, we synthesized a CoMnFe-layered double oxide (CoMnFe-LDO) nanozyme composed of multiple transition metal oxides, which demonstrated improved peroxidase and oxidase activities as well as favorable photothermal conversion capability. The CoMnFe-LDO nanozyme was compounded with an injectable GH hydrogel crosslinked by glucose oxidase (GOX) and peroxidase (HRP). This nanocomposite hydrogel overcame the limitations of weak acidity, H₂O₂, and O₂ levels in the tumor microenvironment (TME) and achieved synergetic chemodynamic therapy (CDT), starvation therapy (ST), and photothermal therapy (PTT) effects based on the cascaded catalytic actions of CoMnFe-LDO and GOX to H₂O₂ and glucose.

Enhancing mechanism of arsenic(iii) adsorption by MnO2-loaded calcined MgFe layered double hydroxide

The use of MnO2/MgFe-layered double hydroxide (MnO2/MgFe-LDH) and MnO2/MgFe-layered double oxide (MnO2/MgFe-LDO400 °C) for arsenic immobilization from the aqueous medium is the subject of this research. Fourier transform infrared spectroscopy, X-ray diffraction, X-ray photoelectron spectroscopy, scanning electron microscopy, and transmission electron microscopy were used to characterise MnO2/MgFe-LDH and MnO2/MgFe-LDO400 °C. Based on our developed method, MnO2 was spread on the clay composites' surfaces in the form of a chemical bond. The clay composite exhibited a good adsorption effect on arsenic. The experimental findings fit the pseudo-second-order model well, indicating that the chemisorption mechanism played a significant role in the adsorption process. Furthermore, the Freundlich model suited the adsorption isotherm data of all adsorbents well. The recycling experiment showed that MnO2/MgFe-LDH and MnO2/MgFe-LDO400 °C exhibited good stability and reusability. In summary, MnO2/MgFe-LDH and MnO2/MgFe-LDO400 °C are promising for developing processes for efficient control of the pollutant arsenic.

Efficient degradation of organic pollutants by activated peroxymonosulfate over TiO2@C decorated Mg-Fe layered double oxides: Degradation pathways and mechanism

To activate peroxymonosulfate (PMS) is an efficient way for decomposition of non-biodegradable organic pollutants. Herein, Mg-Fe layered double oxides decorated with Ti₃C₂ MXene-derived TiO₂@C (T/LDOs) were fabricated to efficiently activate PMS for the degradation of Rhodamine B (RhB), acid red 1 (AR1), methylene blue (MB), and tetracycline hydrochloride (TC). The T/LDOs catalyst could decompose 95.8% of RhB, 94.8% of AR1, 84.9% of MB within 10 min, and 82.4% of TC within 60 min. The degradation rate constant of RhB in the optimal T/LDOs/PMS system was approximately 2.5 and 15.7 times higher than that in the Mg-Fe LDOs/PMS system and Mg-Fe LDH/PMS system, respectively. Importantly, the T/LDOs exhibited a wide working pH range (3.1-11.0) and high stability with low metal ions leaching, indicating its potential practical applications. Quenching experiments and electronic spin resonance results confirmed that both ^•O₂^- and ¹O₂ were the dominant active species in the T/LDOs/PMS system. In addition, the possible degradation pathway of RhB in the 5%-T/LDOs/PMS system was proposed. Finally, the catalytic mechanism study revealed that the T/LDOs with abundant surface hydroxyl groups and a certain amount of TiO₂@C facilitated the electron transfer between ≡Fe^(Ⅲ)‒OH complex and HSO₅^-, boosting the generation of ^•O₂^- and ¹O₂. This study provides an insight into exploiting highly efficient catalysts for PMS activation towards the degradation of organic pollutants.