Removal of tetracycline from livestock wastewater by positive single pulse current electrocoagulation: Mechanism, toxicity assessment and cost evaluation

Anodic oxidation by electrical power pulses for alachlor degradation

This article explores the benefits of electrochemical oxidation in pulsed mode, using potential, current, and power pulses. While potential and current pulse electrochemical technology has been previously studied for wastewater treatment, no study has included power pulses until now. The objective of this work is to highlight the advantages of power pulses by applying this pulse type to the electrochemical oxidation of a probe molecule, alachlor. For this aim, the influence of operating parameters and the comparison of the different pulse modes were investigated and compared to the results obtained with the electrochemical oxidation of alachlor in continuous mode. The study shows that the best results were obtained with the power pulse electrochemical oxidation with 100% alachlor degradation after 180 min and a mineralisation yield of 38.3% after 240 min. These results were better than those reported in the literature for treatments with continuous current input using platinum electrodes. This new technique could be an effective and efficient way to treat contaminated water and reduce the pressure on freshwater reserves.

Electrocoagulation of landfill leachate: Transforming a hazardous residue into a source of irrigation water

Electrocoagulation of landfill leachate has been widely investigated, however, only few reports include the reuse of the treated water. In this work, treated leachate is evaluated as irrigation water. The main obstacle is the high Sodium Absorption Ratio (SAR=Na+/(Ca2++Mg2+)/2. Reducing this indicator involves decreasing Na+ and increasing Mg2+ or Ca2+. Sodium concentration reduction is difficult by electrochemical methods (E0 = -2.71 V); Ca2+ increasing is not feasible as it precipitates. Hence, the use of different Al-Mg anodes was tested tending to increase Mg2+ concentration in the treated water The alloy 88%wtAl-12%wtMg was able to remove 52.9% of COD, 98.1% of turbidity, 97.9% of color, obtaining a SAR of 8.2 meq·L-1, total hardness (TH) of 64.2 meq·L-1 and a soluble sodium percentage (SSP) of 75.8 meq·L-1. This was achieved by working at a current density of 15 mA cm-2, a treatment time of 15 min and a pH 5.0. The phytotoxicity of the treated leachate was evaluated by the germination index using Lactuca Sativa L., reaching a value of 83.2%, which is considered excellent for irrigation water. During growth, 3-4 primary leaves were observed in seedings after 21 days, similar to when potable water was used. The results demonstrate that electrocoagulation is an adequate treatment technique for the reuse of landfill leachate if appropriated materials are used as anodes working in well selected operational variables.

Fabrication and optimization of bioelectrochemical system using tetracycline-degrading bacterial strains for antibiotic wastewater treatment

In this study, a microbial fuel cell was constructed using Raoultella sp. XY-1 to efficiently degrade tetracycline (TC) and assess the effectiveness of the electrochemical system. The degradation rate reached 83.2 ± 1.8 % during the 7-day period, in which the system contained 30 mg/L TC, and the degradation pathway and intermediates were identified. Low concentrations of TC enhanced anodic biofilm power production, while high concentrations of TC decreased the electrochemical activity of the biofilm, extracellular polymeric substances, and enzymatic activities associated with electron transfer. Introducing electrogenic bacteria improved power generation efficiency. A three-strain hybrid system was fabricated using Castellaniella sp. A3, Castellaniella sp. A5 and Raoultella sp. XY-1, leading to the enhanced TC degradation rate of 90.4 % and the increased maximum output voltage from 200 to 265 mV. This study presents a strategy utilizing tetracycline-degrading bacteria as bioanodes for TC removal, while incorporating electrogenic bacteria to enhance electricity generation.

Defluoridation by positive single-pulse current electrocoagulation from photovoltaic wastewater: Energy consumption assessment and mechanism analysis

The presence of fluoride ions (F-) in photovoltaic (PV) wastewater significantly affects the integrity of the ecological environment. In contrast to direct current electrocoagulation (DC-EC), positive single-pulse electrocoagulation (PSPC-EC) shows a significant reduction in both the formation of passivation films on electrodes and the consumption of electrical energy. Under the experimental conditions of an Al-Al-Al-Al electrode combination, an electrode spacing of 1.0 cm, a NaCl concentration of 0.05 mol L-1, an initial pH of 5.6, an initial F- concentration of 5 mg L-1, a current density of 5 A m-2, a pulse frequency of 500 Hz, and a 40 % duty cycle, the achieved equilibrium F- removal efficiencies were 84.0 % for DC-EC and 88.0 % for PSPC-EC, respectively, accompanied by power consumption of 0.0198 kWh·mg-1 and 0.0073 kWh·mg-1. The flocs produced in the PSPC-EC process were characterized using scanning electron microscopy, X-ray diffraction, Fourier transform infrared spectroscopy, and X-ray photoelectron spectroscopy and it is revealed that the F- removal mechanisms in the PSPC-EC process include co-precipitation, hydrogen bond complexation, and ion exchange. When the actual PV wastewater was finally subjected to treatment under the optimal PSPC-EC conditions, the F- concentration in the wastewater was reduced from 4.6 mg L-1 to 1.4 mg L-1. This paper provides both a theoretical framework and a technological basis for the application of PSPC-EC in the advanced treatment of PV wastewater.

Reduction of organic matter containing benzimidazole and toxicity in real livestock wastewater through advanced oxidation processes

Livestock wastewater (LWW) has a complex characteristic of high organic matter content, metals, nutrients, and pharmaceutical compounds. Advanced oxidation processes (AOP) are a potential option for treating this wastewater. This study evaluated real LWW and the performance of UV/H2O2 and UV/peroxymonosulfate (UV/PMS) for its treatment. The experiments were conducted in a UV photoreactor (16 mW/m2, λ = 254 nm). The oxidant agents (Ox) tested were H2O2 and PMS, each at low, medium, and high TOC/Ox molar ratios. A pretreatment based on chemical precipitation was implemented. Annually, the LWW showed total organic carbon (TOC) values of 859 ± 13.37 mg/L, 168.85 ± 1.62 mg/L of total Kjeldahl nitrogen (TKN), and toxicity of 96% v/v. In the dry season, albendazole (ABZ) (95.3 ± 35.16 mg/L), Cu (4.3 ± 0.23 mg/L), Fe (3.8 ± 0.38 mg/L), and suspended solids (SS) (1015 ± 586.9 mg/L) were identified, so pretreatment was implemented. The UV/PMS process with the lowest molar ratio [TOC/Ox 1:0.75] removed significantly lower TOC concentrations (p < 0.05), but toxicity decreased entirely. The study of mineralization and toxicity provided insight into the changes in LWW during treatment with AOP. Furthermore, it contributed to establishing the technical basis for implementing efficient treatment processes.

Ecotoxicological risk assessment on coagulation-flocculation in water/wastewater treatment: a systematic review

It is undeniable that removal efficiency is the main factor in coagulation-flocculation (C-F) process for wastewater treatment. However, as far as environmental safety is concerned, the ecotoxicological aspect of the C-F process needs to be examined further. In this study, a systematic review was performed based on publications related to the toxicity research in C-F technology for wastewater treatment. Through a series of screening steps, available toxicity studies were categorized into four themes, namely acute toxicity, phytotoxicity, cytotoxicity, and genotoxicity, which comprised 48 articles. A compilation of the methodologies executed for each theme was also outlined. The findings show that conventional metallic coagulants (e.g., alum, iron chloride, and iron sulfate) were less toxic when tested on test species such as Daphnia magna (water flea), Lattuca sativa (lettuce), and animal cells compared to synthetic polymers. Natural coagulants such as chitosan or Moringa oleifera were less toxic compared to metallic coagulants; however, inconsistent results were observed. Moreover, an advanced C-F (electrocoagulation) as well as integration between C-F and Fenton, adsorption, and photocatalytic does not significantly change the toxicological profile of the system. It was found that diverse coagulants and flocculants, species sensitivity, complexity in toxicity testing, and dynamic environmental conditions were some key challenges faced in this field. Finally, it was expected that advances in technology, interdisciplinary collaboration, and a growing awareness of environmental sustainability will drive efforts to develop more effective and eco-friendly coagulants and flocculants, improve toxicity testing methodologies, and enhance the overall efficiency and safety of water and wastewater treatment processes.

Highly efficient treatment of tetracycline using coupled electro-Fenton and electrocoagulation process: Mechanism and toxicity assessment

In this study, a novel carbon fiber brush (CFB) electrode was designed using carbon fiber filaments and conductive metals. It was used as the cathode to construct an efficient coupled electro-Fenton and electrocoagulation (EF-EC) process for tetracycline (TC) treatment. An optimal 97.9% removal rate of 10 mg L-1 TC was achieved within 20 min. The coupled process is less pH-dependent and more effective in treating TC compared to the traditional individual electro-Fenton (EF) or electrocoagulation (EC) process, achieving efficient TC removal under neutral pH conditions. The removal rate of 10 mg L-1 TC consistently remained above 92% at 20 min after ten cycle experiments using the same electrodes in a Fe-CFB system (92.7-97.9%), indicating excellent reusability and stability of the CFB cathode. Mechanism analysis showed both EF and EC processes were involved in the system. Radicals (such as •OH and SO4-•) generated by EF contributed to the degradation of TC, yielding nine intermediates. Coagulants (such as Fe(OH)3) generated by EC contributed to the removal of TC. Toxicity prediction results indicated that over half of the nine intermediates exhibited lower biotoxicity compared to TC. This study provides a feasible alternative cathode for the efficient treatment of TC using EF-EC process.

Tourmaline/pyrite dual mineral photocatalysis with a powerful surface electric field for efficient antibiotic removal

Pyrite (FeS2) has garnered attention due to its narrow bandgap, high light absorption, and low cost. However, the rapid recombination of charge carriers hinders its practical application. Surface electric field is a unique characteristic of tourmaline, which can induce effective separation of photo generated electrons and holes. This study successfully combined two directly mined natural minerals, tourmaline and pyrite, to form TFS. Characterization and experiments show that the surface electric field of tourmaline can significantly enhance the photocatalytic activity of TFS. Tetracycline (TC, 50 ppm) was degraded by 95% with 60 min, and the TFS reaction rate constant reached 0.0439 min-1, which is 6.1 times and 17.3 times higher than that of tourmaline and FeS2. Additionally, it significantly improved light absorption and charge carrier separation capabilities. After simulating various natural environmental factors, TFS demonstrated practicality. Considered analysis of active substances and detection revealed that h+ and 1O2 radicals are significant contributors, and the photocatalytic mechanism was proposed. Furthermore, the transformation pathways and toxicity of metabolites were studied. This research offers further inspiration and insights for improving photocatalytic material performance and the green governance environment of natural resources.

Electric field driven tourmaline/hematite dual mineral photocatalysis for efficient antibiotic removal

Hematite (Fe2O3) has garnered attention due to its stability, economic viability, and non-toxic nature. However, the rapid recombination of charge carriers hampers its practical application. On the other hand, tourmaline's inherent surface electric field facilitates the rapid separation of photogenerated electrons and holes. In this study, two directly mined natural minerals, tourmaline and hematite (TFO), were successfully combined. Characterization and experiments indicate that the pronounced enhancement of photocatalytic activity in Fe2O3 is attributed to the electric field effect on the surface of tourmaline. TFO successfully removes 93% of tetracycline (TC, 50 ppm) within 60 min. The reaction rate constant for TFO composite material (0.0410 min-1) is 8.5 times that of tourmaline (0.0048 min-1) and 14.1 times that of hematite (0.0029 min-1). Simultaneously, it markedly improves light absorption and charge carrier separation capabilities. Through simulations of various natural environmental factors, TFO demonstrates excellent practicality. Analyzing and detecting active species revealed the involvement of four types of active species, with ·OH radicals making the most significant contribution. The photocatalytic mechanism was proposed. Furthermore, the degradation pathway of tetracycline and the toxicity of its metabolites were investigated. This work provides additional inspirations and insights for photocatalytic materials performance enhancement and natural resources green governance environment.

Non-thermal technologies for broiler litter processing: Microbial safety, chemical composition, nutritional value, and fermentation parameters in vitro

BACKGROUND

Annually, a massive amount of broiler litter (BL) is produced in the world, which causes soil and surface water pollution due to its high nitrogen content and microbial count. While ruminants can use this non-protein nitrogen (NPN) source for microbial protein synthesis. This issue becomes more critical when protein sources are unavailable or very expensive. One of the sources of NPN is BL which is produced at a considerable amount in the world yearly.

OBJECTIVES

This aim of this research was to conduct a survey of non-thermal technologies such as electrocoagulation (EC), ultraviolet (UV) radiation, and ultrasound (US) waves on the microbial safety and nutritional value of BL samples as a protein source in ruminant diets.

MATERIALS AND METHODS

The methodology of this study was based on the use of an EC device with 24 V for 60 min, UV-C light radiation (249 nm) for 1 and 10 min, and US waves with a frequency of 28 kHz for 5, 10 and 15 min to process BL samples compared with shade-dried samples. Chemical composition and nutritional values of processed samples were determined by gas production technique and measurement of fermentation parameters in vitro.

RESULTS

Based on the results, microbial safety increased in the samples processed with the US (15 min). The EC method had the best performance in reducing the number of fungi and mould. However, none of the methods could remove total bacteria and fungi. Digestibility of BL was similar in shade-dried, EC, and US (10 min) treatments. In general, the use of EC and US15 without having adverse effects on gas production caused a decrease in the concentration of ammonia nitrogen. In contrast, it caused a decrease in neutral detergent fibre (NDF) in the investigated substrate.

CONCLUSIONS

In general, it can be concluded that the use of US5 and EC methods without having a negative effect on the parameters of gas production and fermentation in vitro, while reducing NDF, causes a significant reduction in the microbial load, pathogens, yeast, and mould. Therefore, it is suggested to use these two methods to improve feed digestibility for other protein and feed sources.

Response surface methodology for process optimization in livestock wastewater treatment: A review

With increasing demand for meat and dairy products, the volume of wastewater generated from the livestock industry has become a significant environmental concern. The treatment of livestock wastewater (LWW) is a challenging process that involves removing nutrients, organic matter, pathogens, and other pollutants from livestock manure and urine. In response to this challenge, researchers have developed and investigated different biological, physical, and chemical treatment technologies that perform better upon optimization. Optimization of LWW handling processes can help improve the efficacy and sustainability of treatment systems as well as minimize environmental impacts and associated costs. Response surface methodology (RSM) as an optimization approach can effectively optimize operational parameters that affect process performance. This review article summarizes the main steps of RSM, recent applications of RSM in LWW treatment, highlights the advantages and limitations of this technique, and provides recommendations for future research and practice, including its cost-effectiveness, accuracy, and ability to improve treatment efficiency.

Insights into antibiotic and heavy metal resistance interactions in Escherichia coli isolated from livestock manure and fertilized soil

Heavy metal and antibiotic-resistant bacteria from livestock feces are ecological and public health problems. However, the distribution and relationships of antibiotic resistance genes (ARGs), heavy metal resistance genes (HMRGs), and virulence factors (VFs) and their transmission mechanisms remain unclear. Therefore, we investigated the resistance of Escherichia coli, the prevalence of its ARGs, HMRGs, and VFs, and their transmission mechanisms in livestock fresh feces (FF), composted feces (CF), and fertilized soil (FS). In total, 99.54% (n = 221) and 91.44% (n = 203) of E. coli were resistant to at least one antibiotic and one heavy metal, respectively. Additionally, 72.52% (n = 161) were multi-drug resistant (MDR), of which Cu-resistant E. coli accounted for 72.67% (117/161). More than 99.34% (88/89) of E. coli carried multidrug ARGs, VFs, and the Cu resistance genes cueO and cusABCRFS. The Cu resistance genes cueO and cusABCRFS were mainly located on chromosomes, and cueO and cusF were positively associated with HMRGs, ARGs, and VFs. The Cu resistance genes pcoABCDRS were located on the plasmid pLKYL-P02 flanked by ARGs in PF18C from FF group and on chromosomes flanked by HMRGs in SAXZ1-1 from FS group. These results improved our understanding of bacterial multidrug and heavy metal resistance in the environment.

A review of antibiotics in surface water and their removal by advanced electrocoagulation technologies

The overuse and misuse of antibiotics have posed a serious threat to environment and human health, and even given rise to antibiotic resistance genes (ARGs). Antibiotics are ubiquitous in surface water worldwide with concentrations ranging from ng/L to μg/L level, being widely detected in rivers, lakes, seawater, and even drinking water. To address this thorny issue, numerous advanced technologies have been implemented to remove antibiotics. Advanced electrocoagulation (AEC) technologies, known as the combination of EC and other technologies capable of generating •OH in situ, have garnered considerable attention owing to their advances and high efficiency. This critical review investigated >120 relevant publications from the last few years (2017-2023) for the global distribution of commonly used antibiotics in surface water and their removal by various AEC technologies. Significant AEC technologies, such as combined electro-Fenton and EC (EF-EC) and combined electro-oxidation and EC (EO-EC), were reviewed. Their mechanism and characteristics were detailed. The major research results on removing antibiotics or the application potentials were elaborately described and discussed. Finally, the application trends of AEC technologies, as well as the challenges that may arise were prospected. The recommendations for controlling global antibiotic contamination in surface water were shared.

Purification mechanism of microbial metabolism in kitchen-oil wastewater enhanced by cationic vacancies on γ-Al2O3

The use of catalyst materials to mediate the enhancement of microbial degradation in wastewater is a new economic and energy saving breakthrough in water treatment technology. In this study, γ-Al2O3, which is commonly used as catalyst/carrier, is used as biological filler to treat kitchen-oil wastewater with low biodegradability, and the COD removal rate is about 50 %. It is found that the complexation of cationic vacancies on Al2O3 surface with extracellular polymeric substance (EPS) secreted by microorganisms in wastewater lead to the polarization of electron distribution on biofilm. The efficient degrading bacteria are enriched on reaction interface and obtain electrons to maintain electron dynamic balance by enhancing the transmembrane metabolism of pollutants. The aluminum vacancies on Al2O3 surface accelerate the microbial degradation of pollutants. The cationic vacancies in the structure of catalyst accelerate the acquisition of exogenous electrons by microorganisms without the addition of external energy, which provides a new idea for catalytic fillers to enhance wastewater degradation.

Impacts of draw solutes on the fate of tetracycline in an osmotic membrane bioreactor: Role of the combination between membrane fouling and microorganisms

Osmotic membrane bioreactors (OMBRs) are considered a suitable technology for treating wastewater containing tetracycline due to their high rejection and biodegradation efficiency. However, the impact of membrane fouling layer (i.e., chemical composition, microbial composition, and formation) on the filtration and biodegradation of tetracycline is still unclear. Herein, the effects of draw solute concentration and type on the formation of a membrane fouling layer for tetracycline filtration and its relationship with microbial activity were investigated. The results showed that over 99% of tetracycline was retained on the feed side by membrane rejection, and the fouling layer played an important role in tetracycline filtration. Specifically, membrane foulants resulted in a more hydrophilic membrane facilitating tetracycline filtration, while the tetracycline-degrading genera from the fouled membrane promoted tetracycline degradation. The structure equation model showed that tetracycline filtration dominated by electrostatic repulsion between tetracycline and the fouled membrane was more important than tetracycline degradation for tetracycline removal (path coefficient of 0.655 vs. 0.395). This study provided insights into the combined effect of membrane foulants and microorganisms on tetracycline removal.

Facile design of surface electric field driven tourmaline/g-C3N4 layered stacked photocatalysts with enhanced photocatalytic activity for antibiotic removal

In the field of photocatalysis, Graphitic carbon nitride (g-C₃N₄) has received a lot of attention for its superior functionality and benefits. However, it suffers from the fatal defect of low charge separation efficiency, which is well addressed by tourmaline's self-contained surface electric field. In this work, tourmaline/g-C₃N₄ (T/CN) composites were successfully synthesized. Due to its surface electric field effect, tourmaline and g-C₃N₄ are stacked on top of each other. It makes its specific surface area increase greatly and more active sites are exposed. Additionally, the rapid separation of photogenerated electron holes under the action of electric field promotes the photocatalytic reaction. T/CN exhibited excellent photocatalytic performance under visible light, with 99.9% Tetracycline (TC 50 mg L^-1) removal after 30 min. Compared to tourmaline (0.0160 min^-1) and g-C₃N₄ (0.0230 min^-1), the T/CN composite's reaction rate constant (0.1754 min^-1) was 11.0 and 7.6 times higher. A series of characterizations also determined the structural properties and catalytic performance of the T/CN composites, which were found to have a larger specific surface area, narrower band gap, and higher charge separation efficiency compared to the monomer. In addition, the toxicity of tetracycline intermediates and their degradative pathways were investigated, and the toxicity of the intermediates was found to be reduced. Given the quenching experiments and active substance determination, it was also found that h⁺ and ·O₂^- play a major role. This work provides more inspiration for photocatalytic material performance research as well as green innovation for environmental management.

Enhanced purification of kitchen-oil wastewater driven synergistically by surface microelectric fields and microorganisms

The stable structure and toxic effect of refractory organic pollutants in wastewater lead to the problem of high energy consumption in water treatment technology. Herein, we propose a synergistic purification of refractory wastewater driven by microorganisms and surface microelectric fields (SMEF) over a dual-reaction-center (DRC) catalyst HCLL-S8-M prepared by an in situ growth method of carbon nitride on the Cu-Al₂O₃ surface. Characterization techniques demonstrate the successful construction of SMEF with strong electrostatic force over HCLL-S8-M based on cation-π interactions between metal copper ions and carbon nitride rings. With the catalyst as the core filler, an innovative fixed bed bioreactor is constructed to purify the actual kitchen-oil wastewater. The removal efficiency of the wastewater even with a very low biodegradability (BOD₅/COD = 0.33) can reach 60% after passing through this bioreactor. An innovative reaction mechanism is revealed for the first time that under the condition of a small amount of biodegradable organic matter, the SMEF induces the enrichment of electric active microorganisms (Desulfobulbus and Geobacter) in the wastewater, accelerates the interspecies electron transfer of intertrophic metabolism with the biodegradable bacteria through the extracellular electron transfer mechanism such as cytochrome C and self-secreted electron shuttle. The electrons of the refractory organic pollutants adsorbed on the surface of the catalyst are delocalized by the SMEF, which can be directly utilized by microorganisms through EPS conduction. The SMEF generated by electron polarization can maximize the utilization of pollutants and microorganisms in wastewater and further enhance degradation without adding any external energy, which is of great significance to the development of water self-purification technology.

Efficient removal of norfloxacin from water using batch airlift-electrocoagulation reactor: optimization and mechanisms analysis

In this study, we developed an airlift-electrocoagulation (AL-EC) reactor to remove norfloxacin (NOR) from water. Six parameters influencing NOR removal were investigated, and the possible removal mechanism was proposed based on flocs characterization and intermediates analysis. The performances for treating different antibiotics and removing NOR from 3 types of water were also evaluated. The best NOR removal efficiency was obtained with the iron anode and aluminum cathode combination, a current density of 2 mA cm-2, an initial pH of 7, a treatment time of 32 minutes and an air flow rate of 200 mL min-1, the supporting electrolyte type was NaCl, and the initial NOR concentration was 10 mg L-1. Flocs adsorption and electrochemical oxidation were the main ways to remove NOR from water. The average removal efficiency of the AL-EC reactor exceeded 60% of the different antibiotic concentrations in artificial and real water. The highest NOR removal rate reached 93.48% with an operating cost of 0.153 USD m-3. The present work offers a strategy for NOR removal from water with high efficiency and low cost, showing a huge potential for the application of the AL-EC in antibiotic contaminated water treatment.

Tetracycline removal from aqueous solution by electrooxidation using ruthenium-coated graphite anode

This paper reports the electrochemical oxidation treatment of 80 mL of acidic aqueous solutions with 0.2 mM of the drug tetracycline in 25 mM Na₂SO₄ using a lab-scale electrochemical cell. The performance of tetracycline removal with Ru-coated graphite by the chemical bath deposition (CBD) and raw graphite anode has been demonstrated. The effects of operating parameters were tested such as pH, applied current, supporting electrolyte concentration, and initial tetracycline concentration. The best tetracycline degradation was obtained with Ru-coated graphite anode due to its higher oxidation power, which allowed the complete degradation of refractory compounds. The modified surface structure of the Ru-coated graphite anode was characterized by scanning electron microscopy (SEM), atomic force microscopy (AFM), and energy-dispersive X-ray (EDX). The EO process with Ru-coated graphite anode allowed 93.8% tetracycline abatement after 100 min of electrolysis at an applied current of 100 mA. In all cases, tetracycline decay obeyed pseudo-first-order kinetics. The tetracycline removal performance of graphite electrodes with nano coating on graphite has offered a performing alternative. A Comparative study revealed that electrolysis with Ru-coated graphite acted as a better electrode material than raw graphite for the catalytic reaction.

The role of the current waveform in mitigating passivation and enhancing electrocoagulation performance: A critical review

Electrocoagulation (EC) can be an efficient alternative to existing water and wastewater treatment methods due to its eco-friendly nature, low footprint, and facile operation. However, the electrodes applied in the EC process suffer from passivation or fouling, an issue resulting from the buildup of poorly conducting materials on the electrode surface. Indeed, such passivation gives rise to various operational problems and restricts the practical implementation of EC on a large scale. Therefore, it has been suggested that using pulsed direct current (PDC), alternating pulse current (APC), and sinusoidal alternating current (AC) waveforms in EC as alternatives to conventional direct current (DC) can help mitigate passivation and alleviate its associated detrimental effects. This paper presents a critical review of the impact of the current waveform on the EC process towards the capabilities of the PDC, APC, and AC waveforms in de-passivation and performance enhancement while comparing them to the conventional DC. Additionally, current waveform parameters influencing the surface passivation of electrodes and process efficiency are elaborately discussed. Meanwhile, the performance of the EC process is evaluated under different current waveforms based on pollutant removal efficiency, energy consumption, electrode usage, sludge production, and operating cost. The proper current waveforms for treating various water and wastewater matrices are also explained. Finally, concluding remarks and outlooks for future research are provided.

Removal of ofloxacin from wastewater by chloride electrolyte electro-oxidation: Analysis of the role of active chlorine and operating costs

Electro-oxidation (EO) has received increasing attention as an efficient and green method for removing pollutants from wastewater. Chloride anions (Cl^-), which commonly exist in wastewater, can act as an electrolyte for the EO process. However, the role of reactive chlorine species (RCS) generated near electrodes is often underestimated. In this study, we generated hydroxyl radicals (OH) and RCS in a boron-doped diamond (BDD) electrode system and investigated its degradation mechanism for ofloxacin (OFX) removal. The findings suggested that OFX degradation was dominated by OH existing near the anode in solution, with RCS playing a supporting role. Based on the produced intermediates, we proposed an OFX decomposition pathway. The biological toxicities of the intermediates were evaluated through the ECOSAR and T.E.S.T. procedure. Nearly half of the intermediates are less toxic than the parent compound. After optimizing the operating parameters by the response surface methodology, 20 mg/L OFX was almost completely degraded after 10 min of reaction in 1.45 g/L NaCl with a current density (j) of 18 mA/cm², and the total organic carbon was decreased by 30.55 %. The energy consumption and current efficiency were 0.648 kW·h/g_TOC and 8.65 %, respectively. Comparing the operating costs of the proposed and other EO methods, our method emerged as a viable new treatment scheme for similar polluted wastewaters. This study aims to comprehensively understand the potential application value of BDD electrodes in the treatment of Cl^- containing organic wastewater.

Efficient removal of antibiotic in single and binary mixture of nickel by electrocoagulation process: Hydrogen generation and cost analysis

In discharged water, antibiotics and heavy metals frequently coexist, forming stable and recalcitrant complexes. Environmental concerns about how to efficiently treat this type of pollution are growing. Using Fe and Al electrodes, electrocoagulation (EC) was applied to remove tetracycline (TC) as a single pollutant as well as TC-nickel ions in a binary mixture from water. The effects of critical variables and the TC-Ni molar ratio (1:1, 1:2, and 2:1) were studied. The Fe electrode achieved 99.3% TC removal after 60 min in a single pollutant system containing 15 mgL^-1 of TC, while the Al electrode achieved 99.8% removal in 20 min at optimal conditions. The EC process demonstrated excellent electrodegradation efficiency towards TC-Ni complexes. When the TC to Ni²⁺ ratio was 1:1 and 1:2, respectively, TC elimination was 100% in 10 min and 99.6% in 20 min. We noted that a sufficient amount of Ni²⁺ could increase TC decomposition by electrocatalysis. The amount of hydrogen gas produced after treatment of a 0.2 L TC solution alone is 22.2-13.99 mol m^-3, whereas it was 27.2-40.8 mol m^-3 in the TC-Ni binary mixture, which can generate more than 35% of the electrical energy needed to power the EC system. To evaluate the generated sludge, FTIR analysis was performed.