Development of a microfluidic-chip system for liquid–phase microextraction based on two immiscible organic solvents for the extraction and preconcentration of some hormonal drugs

Applying a microfluidic device to improve the Ca2+ separation performance of the liquid-liquid extraction process

This study investigates the application of extraction solvent in a new microfluidic apparatus to separate calcium ions (Ca²⁺). Indeed, a serpentine microfluidic device has been utilized to separate calcium ions. The flow regime map shows that it is possible to completely separate organic and aqueous phases using the serpentine microfluidic device. The suggested microfluidic device reaches the extraction efficiency of 24.59% at 4.2 s of the residence time. This research also employs the Box-Behnken design (BBD) strategy in the response surface methodology (RSM) for performing the modeling and optimization of the suggested extraction process using the recorded experimental data. Flow rate and pH of the aquatic phase as well as Dicyclohexano-18-crown-6 (DC18C6) concentration are those independent features engaged in the model derivation task. The optimum values of pH 6.34, the DC18C6 concentration of 0.015 M, and the flow rate = 20 µl/min have been achieved for the aquatic phase. The results indicated that the extraction efficiency of Ca²⁺ is 63.6%, and microfluidic extraction is 24.59% in this optimum condition. It is also observed that the microfluidic extraction percentage and experimental efficiency achieved by the suggested serpentine microchannel are higher than the previous separation ranges reported in the literature.

Intensified decontamination of amoxicillin drug wastewater assisted by liquid-phase micro extraction method

The presence of pharmaceutical pollutants, including antibiotic contaminants in the environment is one of the most important issues in the world today. We focused on elimination of amoxicillin (AMX) from aqueous media in micro Channel Y-Y shaped. The kinetic studies showed that the reaction kinetic was very fast and extraction equilibrium is attained within 20 s. Key operational parameters such as feed concentration, pH of aqueous solution, and extractant concentration and residence time were optimized. The maximum rate of AMX removal was determined 98.2%. Overall volumetric mass transfer coefficient of amoxicillin kLα, is perused to specify the mass transfer performance. Much higher amoxicillin kLα values acquired in the micro process compare with conventional extraction approved the amoxicillin is easily extracted with a higher ratio at micro-flow. The studies demonstrated that the micro solvent extraction process has considerable potential for environmentally friendly and would be a promising method for wastewater treatment of complex systems.Highlights On-chip liquid-phase microextraction coupled with UV-VIS was introduced.Extraction percentage of 98.2% was obtained using MDEHPA under best conditions.Microfluidic shows the considerable potential for environmentally friendly and amoxicillin removal from aqueous media.

Developments of Microextraction (Extraction) Procedures for Sample Preparation of Antidepressants in Biological and Water Samples, a Review

Antidepressants are an important class of drugs to treat various types of depression. The determination of antidepressants is crucial in biological samples to control adverse effects in humans and study pharmacokinetics and bioavailability. Direct measurement of antidepressants in biological and water samples is a considerable challenge for analysts due to their low concentration, the high matrix effects of real samples, and the presence of metabolites of these drugs in biological samples. The challenge leads to using sample preparation processes as a critical step in determining antidepressants. Extraction and microextraction procedures have been widely utilized as sample preparation procedures for these drugs. The purposes of extraction or microextraction methods for antidepressant medications are to preconcentrate the analyte, reduce the matrix effects, increase the selectivity of the procedures, and convert the sample to a suitable format for introducing it into detection systems. In the review, the various extraction and microextraction methods of these drugs in biological, real water, and wastewater samples were investigated. The theory of each technique was briefly addressed to understand the features and factors affecting each method. The extraction and microextraction methods were classified based on their application for antidepressants, and the advantages and disadvantages of each technique were reviewed. The new developments to overcome the limitations of each procedure were discussed. The investigation indicated the number of applications of liquid-phase microextraction for extracting antidepressants has been almost equal to that of solid-phase microextraction.

Green microfluidic liquid-phase microextraction of polar and non-polar acids from urine

In this work, hippuric acid (log P = 0.5), anthranilic acid (log P = 1.3), ketoprofen (log P = 3.6), and naproxen (log P = 3.0) were simultaneously extracted by a green microfluidic device based on the principles of liquid-phase microextraction (LPME). Different deep eutectic solvents (DESs) were investigated as supported liquid membrane (SLM), and a mixture of camphor and menthol as eutectic solvents in the molar ratio 1:1 was found to be highly efficient for the simultaneous extraction of non-polar and polar acidic drugs. LPME was conducted for 6 min per sample. Urine sample was delivered to the system at 1 μL min^-1, and target analytes were extracted exhaustively (75-100% recovery) across the DES SLM, and into pure aqueous phosphate buffer pH 11.0 delivered as acceptor at 1 μL min^-1. The acceptor was analyzed with liquid chromatography-UV detection. Interestingly, the DES enabled extraction of both the polar and non-polar model analytes at the same time; all chemicals were green and non-hazardous, and the chemical waste was less than 1 mg per sample.

Application of Microfluidic Chip Technology in Food Safety Sensing

Food safety analysis is an important procedure to control food contamination and supervision. It is urgently needed to construct effective methods for on-site, fast, accurate and popular food safety sensing. Among them, microfluidic chip technology exhibits distinguish advantages in detection, including less sample consumption, fast detection, simple operation, multi-functional integration, small size, multiplex detection and portability. In this review, we introduce the classification, material, processing and application of the microfluidic chip in food safety sensing, in order to provide a good guide for food safety monitoring.

Miniaturized sample preparation methods for saliva analysis

Saliva, as the first body fluid encountering with the exogenous materials, has good correlation with blood and plays an important role in bioanalysis. However, saliva has not been studied as much as the other biological fluids mainly due to restricted access to its large volumes. In recent years, there is a growing interest for saliva analysis owing to the emergence of miniaturized sample preparation methods. The purpose of this paper is to review all microextraction methods and their principles of operation. In the following, we examine the methods used to analyze saliva up to now and discuss the potential of the other microextraction methods for saliva analysis to encourage research groups for more focus on this important subject area.

Application of microfluidic chip technology in pharmaceutical analysis: A review

The development of pharmaceutical analytical methods represents one of the most significant aspects of drug development. Recent advances in microfabrication and microfluidics could provide new approaches for drug analysis, including drug screening, active testing and the study of metabolism. Microfluidic chip technologies, such as lab-on-a-chip technology, three-dimensional (3D) cell culture, organs-on-chip and droplet techniques, have all been developed rapidly. Microfluidic chips coupled with various kinds of detection techniques are suitable for the high-throughput screening, detection and mechanistic study of drugs. This review highlights the latest (2010–2018) microfluidic technology for drug analysis and discusses the potential future development in this field.

Local surface modification at precise position using a chemical pen

Push-pull cannula system, which was first proposed by Gaddum, has grown to be an important method for the perfusion of brain and region-selective surface treatment. However, reported push-pull cannula systems only concerned on single reagent applications. Microfluidic system was then an exciting tool for multi-reagent treatment on substrate in closed microchannels. Nowadays, it is still a challenge to apply online mixing and reaction for surface pattern in an open environment. Here, we present a novel method using a chemical pen that enables region-selective online chemical reactions for the micro-surface modification/patterning. We utilized this method to fabricate labeling protein array using an online labeling strategy. Moreover, the device was applied for local modification of biomaterials surface by using a three-component reaction at precise position. This tool was the first demonstration of design to perform online reaction of two different reagents on a real solid sample in an open environment. It was demonstrated a useful method for protein array fabrication with online labeled protein.

Fabricating and Characterizing the Microfluidic Solid Phase Extraction Module Coupling with Integrated ESI Emitters

Microfluidic chips coupling with mass spectrometry (MS) will be of great significance to the development of relevant instruments involving chemical and bio-chemical analysis, drug detection, food and environmental applications and so on. In our previous works, we proposed two types of microfluidic electrospray ionization (ESI) chip coupling with MS: the two-phase flow focusing (FF) ESI microfluidic chip and the corner-integrated ESI emitter, respectively. However the pretreatment module integrated with these ESI emitters is still a challenging problem. In this paper, we concentrated on integrating the solid phase micro-extraction (SPME) module with our previous proposed on-chip ESI emitters; the fabrication processes of such SPME module are fully compatible with our previous proposed ESI emitters based on the multi-layer soft lithography. We optimized the structure of the integrated chip and characterized its performance using standard samples. Furthermore, we verified its abilities of salt removal, extraction of multiple analytes and separation through on-chip elution using mimic biological urine spiked with different drugs. The results indicated that our proposed integrated module with ESI emitters is practical and effective for real biological sample pretreatment and MS detection.

Novel generation of deep eutectic solvent as an acceptor phase in three-phase hollow fiber liquid phase microextraction for extraction and preconcentration of steroidal hormones from biological fluids

In this study, a novel generation of deep eutectic solvents (DESs) was used as an acceptor phase in three-phase hollow fiber liquid phase microextraction (HF-LPME) based on two immiscible organic phases. It was compared with other common DESs for extraction and preconcentration of dydrogesterone (DYD) and cyproterone acetate (CPA) from urine and plasma samples. The extracted analytes were analyzed by high performance liquid chromatography with UV-vis detector (HPLC-UV). This phosphonium based DES due to low volatility, low price and multifunctionality introduced itself as worthy next generation of acceptor phase in HF-LPME. The factors affected on extraction efficiency of the analytes were investigated and optimized. The performance of the proposed method was studied in terms of linear ranges (LRs from 1 to 500µgL^-1 with R² ≥ 0.9946), precision (RSD% ≤ 6.3) and limits of detection (LODs in the range of 0.5-2µgL^-1). Under the optimized conditions, preconcentration factors in the range of 187-428 were obtained. Finally, the method was applied to the analysis of DYD and CPA in human urine and plasma samples and desirable results were obtained.

Pre-concentration by liquid intake by paper (P-CLIP): a new technique for large volumes and digital microfluidics

Microfluidic platforms are an attractive option for incorporating complex fluid handling into low-cost and rapid diagnostic tests. A persistent challenge for microfluidics, however, is the mismatch in the "world-to-chip" interface - it is challenging to detect analytes present at low concentrations in systems that can only handle small volumes of sample. Here we describe a new technique termed pre-concentration by liquid intake by paper (P-CLIP) that addresses this mismatch, allowing digital microfluidics to interface with volumes on the order of hundreds of microliters. In P-CLIP, a virtual microchannel is generated to pass a large volume through the device; analytes captured on magnetic particles can be isolated and then resuspended into smaller volumes for further processing and analysis. We characterize this method and demonstrate its utility with an immunoassay for Plasmodium falciparum lactate dehydrogenase, a malaria biomarker, and propose that the P-CLIP strategy may be useful for a wide range of applications that are currently limited by low-abundance analytes.