Capillary gas chromatography-mass spectrometry: Current trends and perspectives

A Selective Gas Chromatography-Tandem Mass Spectrometry Method for Quantitation of Ethylene and Diethylene Glycol in Paediatric Syrups

Ethylene Glycol (EG) and diethylene Glycol (DEG) are two contaminants known to cause various human health problems. These glycols might be present in drug syrups that are based on glycerol, sorbitol, or polyethylene glycol. In late 2022, several batches of cough, antipyretics, and antihistamine syrups were reported to contain toxic levels of EG and DEG in multiple countries; this incident concerned the World Health Organization (WHO). From an analytical perspective, several methods of glycols analysis in pharmaceuticals have been reported in the literature, with the majority being dedicated to raw material analysis. This study aims to develop a selective method capable of evaluating a wide range of paediatric syrups in order to assess the safety of commercially available paediatric syrups currently distributed in the local market. This research introduces a method for determining glycols utilizing gas chromatography-tandem mass spectrometry (GC-MS/MS), which offers significantly higher selectivity than conventional single quadrupole gas chromatography-mass spectrometry (GC-MS). The developed method meets the current International Council for Harmonisation (ICH) guidelines for validation. The absence of any interfering peaks in both the unspiked sample of promethazine syrup and the reference standard solutions proved the method's selectivity. Furthermore, 2,2,2-trichloroethanol was used as an internal standard, and a new GC-MS/MS method was developed to analyze it. The calibration curves for EG and DEG were linear within the selected concentration range of 1-10 μg/mL. The detection limit for both EG and DEG was 400 ng/mL, while the quantification limit was 1 μg/mL. Recovery values for both EG and DEG met the accuracy acceptance criterion. Thus, the developed method proved to be efficient and accurate for determining EG and DEG levels in suspected contaminated syrups.

High Selectivity of A Novel Pillar[5]arene with Ester Units as a Gas Chromatographic Stationary Phase toward Aromatic Isomers

This work reports the first example of employing ester-functionalized pillar[5]arene (P5A-C10-OAc) stationary phase for gas chromatography (GC) separations. The as-fabricated P5A-C10-OAc column achieved improved column efficiency of 4270 plates/m and separation performance in contrast to the P5-C10-Br column. The P5A-C10-OAc column showed good separation performance for a wide range of analytes such as alkanes, bromoalkanes, ketones, fatty acid methyl esters, aldehydes, alcohols, halobenzenes, anilines, phenols, naphthalenes, and showed sharp and symmetrical peak shapes for analytes that are liable to peak-tailing in GC analysis. As testified by the challenging isomer mixtures (bromonitrobenzene, chloronitrobenzene, bromobenzaldehyde, chlorobenzaldehyde, nitrobenzaldehyde), the P5A-C10-OAc column exhibited comprehensively higher separation capability than the P5A-C10-Br, P5A-C10 and commercial HP-35 columns. This work demonstrates the great potential of pillararene-based stationary phases as a new type of stationary phases for GC separations.

Volatile Organic Compounds from Offspring of Stingless Bee Sacrificed in Hygienic Behavior Test

This study shows the profile of volatile organic compounds (VOCs) from pupae and larvae of Melipona quadrifasciata anthidioides Lepeletier subjected to three death induction techniques for hygienic behavior (HB) studies: freezing in liquid nitrogen (LN2), freezing in a freezer (FRZ) and piercing of offspring with an entomological pin (PIN). The VOCs from larvae and pupae were obtained through headspace solid-phase microextraction and characterized using gas chromatography coupled to mass spectrometry. In addition, an HB test was performed on the colonies. The main classes of VOCs were hydrocarbons, terpenes and alcohols. Multivariate analysis was applied and showed that there was a separation in the compound profiles between the different treatments. The HB test in the colonies showed that 24 hours after the application of the techniques, the bees removed more dead larvae in LN2 treatment (83.5 %), while after 48 hours more larvae were removed in the LN2 and FRZ treatments (92.3 %). When compared to pupae removal, larvae removal was significantly faster in LN2.

Contaminants of emerging concern: Silylation procedures, evaluation of the stability of silyl derivatives and associated measurement uncertainty

Analyte range of gas chromatography-mass spectrometry (GC-MS), widely used in environmental analysis, can be significantly broadened by derivatization. Silyl derivatives have improved volatility and thermal stability, chromatographic and mass spectrometric behaviors, and thus detection, structural elucidation and quantification. However, silylation use is often hindered by the stability of generated derivatives and the need to optimize silylation conditions. In this study, we optimized the derivatization conditions for 70 selected contaminants of emerging concern (CEC) using chemometrics approaches. N-methyl-N-(trimethylsilyl) trifluoroacetamide (MSTFA), N, O-bis(trimethylsilyl)trifluoroacetamide (BSTFA) and BSTFA + 1 % trimethylchlorosilane (TMCS) were investigated, among which the latter gave the best yield. CEC were grouped in three derivatization protocols: 60 °C/45 min, 70 °C/90 min, and 70 °C/45 min. The short- and long-term stability of the CEC-trimethylsilyl (TMS) derivatives, i.e. for 28 days and up to 20 weeks were examined in a solvent and artificial wastewater (AWW) extract at 25 °C, 4 °C and - 18 °C, and during repeated five freeze-thaw (F/T) cycles, at two concentration levels: 100 μg/L and 1000 μg/L. Except for TMS derivatives of shikimic acid (SHA), quinic acid (QA) and sulfanilamide (SFA), the remaining derivatized compounds were stable in solvent (EtAc) for 28 days. In AWW extract, TMS derivatives of citric acid (CA), 17β-estradiol (E2), estriol (E3) and 17α-ethinyl estradiol (EE2) were unstable at 25 °C and 4 °C. Within up to 20 weeks, only the TMS derivatives of CA, meso-erythritol (ERY) and bisphenol BP (BPBP) were unstable. The most significant hydrolytic breakdown was observed during repeated F/T cycles. After three cycles, ≤ 20 % of the initial concentration of six and nine CEC-TMS derivatives had degraded in solvent and AWW extracts, respectively. According to the deep statistical comparison (DSC) approach, the most prominent degradation was observed for TMS derivatives of E2, CA, 9-hydroxyfluorene (9-HF), estrone (E1) and trans-3'-hydroxycotinine (T3HC) in solvent; E2, CA, 9-HF, E3 and E1 in AWW extracts and ERY, E2, CA, 9-HF and E1 in both matrices. Finally, the sample concentration of CEC accounted for most of the measurement uncertainty (MU). Based on our findings, we recommend the derivatized samples to be stored at -18 °C for up to 20 weeks to ensure the stability of their TMS derivatives. Sample freezing and thawing of not more than twice is allowed to maintain ≥80 % of the initial CEC-TMS concentration.

Portable capillary LC for in-line UV monitoring and MS detection: Comparable sensitivity and much lower solvent consumption

Pharmaceutical development currently relies on quality separation methods from early discovery through to line-of-site manufacturing. There have been significant advancements made regarding the column particle packing, internal diameter, length connectivity, the understanding of the impact key parameters like void volume, flow rate, and temperature all that affects the resultant separation quality, that is, resolution, peak shape, peak width, run time, and signal-to-noise ratio. There is however a strong need to establish better alternatives to large bulky high-performance liquid chromatography racks either for process analytical reaction monitoring or mass spectrometry analysis in establishing product quality. Compact, portable high-pressure liquid chromatography can be a more efficient alternative to traditional ultra-high pressure liquid chromatography and traditional liquid chromatography. The compact versatile instrument evaluated here allows good separation control with either the on-board column with fixed ultra-violet wavelength cartridge or for use with a high-resolution mass spectrometry. Significant space reduction results in greener lab spaces with improved energy efficiency for smaller labs with lower energy demands. In addition, this compact liquid chromatography was used as a portable reaction monitoring solution to compare forced degradation kinetics and assess portable liquid chromatography-mass spectrometry capability for the analyses required for pharmaceutical drug product testing.

A review of piezoelectric MEMS sensors and actuators for gas detection application

Piezoelectric microelectromechanical system (piezo-MEMS)-based mass sensors including the piezoelectric microcantilevers, surface acoustic waves (SAW), quartz crystal microbalance (QCM), piezoelectric micromachined ultrasonic transducer (PMUT), and film bulk acoustic wave resonators (FBAR) are highlighted as suitable candidates for highly sensitive gas detection application. This paper presents the piezo-MEMS gas sensors' characteristics such as their miniaturized structure, the capability of integration with readout circuit, and fabrication feasibility using multiuser technologies. The development of the piezoelectric MEMS gas sensors is investigated for the application of low-level concentration gas molecules detection. In this work, the various types of gas sensors based on piezoelectricity are investigated extensively including their operating principle, besides their material parameters as well as the critical design parameters, the device structures, and their sensing materials including the polymers, carbon, metal-organic framework, and graphene.

Deep learning-based method for automatic resolution of gas chromatography-mass spectrometry data from complex samples

Modern gas chromatography-mass spectrometry (GC-MS) is the workhorse for the high-throughput profiling of volatile compounds in complex samples. It can produce a considerable amount of two-dimensional data, and automatic methods are required to distill chemical information from raw GC-MS data efficiently. In this study, we proposed an Automatic Resolution method (AutoRes) based on pseudo-Siamese convolutional neural networks (pSCNN) to extract the meaningful features swamped by the noises, baseline drifts, retention time shifts, and overlapped peaks. Two pSCNN models were trained with 400,000 augmented spectral pairs, respectively. They can predict the selective region (pSCNN1) and elution region (pSCNN2) of compounds in an untargeted manner. The accuracies of the pSCNN1 model and the pSCNN2 model on their test sets are 99.9% and 92.6%, respectively. Then, the chromatographic profile of each component was automatically resolved by full rank resolution (FRR) based on the predicted regions by these models. The performance of AutoRes was evaluated on the simulated and plant essential oil datasets. Compared to AMDIS and MZmine, AutoRes resolves more reasonable mass spectra, chromatograms, and peak areas to identify and quantify compounds. The average match scores of AutoRes (925 and 936) outperformed AMDIS (909 and 925) and MZmine (888 and 916) when resolving mass spectra from overlapped peaks on the Set Ⅰ and Set Ⅱ of plant essential oil dataset and matching them against the NIST17 library. It extracted peak areas and mass spectra automatically from 10 GC-MS files of plant essential oils, and the entire process was completed in 8 min without any prior information or manual intervention. It is implemented in Python and is available as an open-source package at https://github.com/dyjfan/AutoRes.

Comparison of different approaches for direct coupling of solid-phase microextraction to mass spectrometry for drugs of abuse analysis in plasma

The direct coupling of solid-phase microextraction (SPME) to mass spectrometry (MS) (SPME-MS) has proven to be an effective method for the fast screening and quantitative analysis of compounds in complex matrices such as blood and plasma. In recent years, our lab has developed three novel SPME-MS techniques: SPME-microfluidic open interface-MS (SPME-MOI-MS), coated blade spray-MS (CBS-MS), and SPME-probe electrospray ionization-MS (SPME-PESI-MS). The fast and high-throughput nature of these SPME-MS technologies makes them attractive options for point-of-care analysis and anti-doping testing. However, all these three techniques utilize different SPME geometries and were tested with different MS instruments. Lack of comparative data makes it difficult to determine which of these methodologies is the best option for any given application. This work fills this gap by making a comprehensive comparison of these three technologies with different SPME devices including SPME fibers, CBS blades, and SPME-PESI probes and SPME-liquid chromatography-MS (SPME-LC-MS) for the analysis of drugs of abuse using the same MS instrument. Furthermore, for the first time, we developed different desorption chambers for MOI-MS for coupling with SPME fibers, CBS blades, and SPME-PESI probes, thus illustrating the universality of this approach. In total, eight analytical methods were developed, with the experimental data showing that all the SPME-based methods provided good analytical performance with R ² of linearities larger than 0.9925, accuracies between 81% and 118%, and good precision with an RSD% ≤ 13%.

A simple soft ionization approach for GC-MS assisted by capillary array

Electron ionization (EI) is the most widely used ionization method in gas chromatography/mass spectrometry (GC-MS). This method possesses a lot of advantages including versatility for various classes of volatile and semi volatile organic compounds, high sensitivity, structure informativity and reproducibility, production of database searchable mass spectra. On the other hand there are a number of compounds, which molecular ions are not stable enough to produce corresponding peaks in EI mass spectra, making it difficult to determine structures of compounds not presented in databases. A new approach allowing easy implementation of EI in a molecular beam formed by a capillary assembly is proposed for discussion in this communication. Primary experimental results achieved using this approach demonstrate its possibility to produce suitable for database search mass spectra with increased intensity of molecular ion peak.

Direct coupling in-tube solid-phase microextraction with mass spectrometry using polymer coated open-tubular column for rapid analysis of antiepileptic drugs in biofluids

Development of high-throughput and rapid screening analytical method is in high demand for anti-doping and clinical point-of-care (POC) analysis. Solid-phase microextraction and mass spectrometry direct coupling (SPME-MS) has been proved as a rapid and effective way for target analysis in complex sample matrixes. An online direct coupling of in-tube SPME (IT-SPME) with MS using polymer coated open-tubular column has been developed in this work. A sharp stainless-steel needle was attached at the end of the SPME column, which enables the direct ionization of the analytes after elution from the IT-SPME column. Itaconic acid-benzene co-polymer was in-situ grown on the inner surface of the fused silica capillary and used as extraction phase. This column has low backpressure and provides both hydrophobic and weak cationic exchange interaction with the target analytes due to the chemical properties. The developed online IT-SPME-MS method showed good extraction performance towards various target analytes and good reusability at least for 60 times. As a proof-of-concept application, the above method was applied for the analysis of antiepileptic drugs (AEDs) in both plasma and urine samples with linear range (1 ng/mL-200 ng/mL), good linearity (R² ≥ 0.99), and good reproducibility (intra-day RSDs less than 4.36%, inter-day RSDs less than 6.55%). The method exhibited high enrichment factors between 187 and 204 for the two AEDs and high sensitivity for the analysis of human plasma samples and urine samples.

Simultaneous Determination for Nine Kinds of N-Nitrosamines Compounds in Groundwater by Ultra-High-Performance Liquid Chromatography Coupled with Triple Quadrupole Mass Spectrometry

The ability to effectively detect N-nitrosamine compounds by liquid chromatography-tandem mass spectrometry presents a challenge due to the problems of high detection limits and difficulty in simultaneous N-nitrosamine compound detection. In order to overcome these limitations, this study reduced the detection limit of N-nitrosamine compounds by applying n-hexane pre-treatment to remove non-polar impurities before the conventional process of column extraction. In addition, ammonium acetate was used as the mobile phase to enhance the retention of nitrosamine target substances on the chromatographic column, with formic acid added to the mobile phase to improve the ionization level of N-nitrosodiphenylamine, to achieve the simultaneous detection of multiple N-nitrosamine compounds. Applying these modifications to the established detection method allowed the rapid and accurate detection of N-nitrosamine in water within 12 min. The linear relationship, detection limit, quantification limit and sample spiked recovery rate of nine types of nitrosamine compound were investigated, showing that the correlation coefficient ranged from 0.9985-0.9999, while the detection limits of the instrument and the method were 0.280-0.928 µg·L^-1 and 1.12-3.71 ng·L^-1, respectively. The spiked sample recovery rate ranged from 64.2-83.0%, with a standard deviation of 2.07-8.52%, meeting the requirements for trace analysis. The method was applied to the detection of N-nitrosamine compounds in nine groundwater samples in Wuhan, China, and showed that the concentrations of N-nitrosodimethylamine and NDEA were relatively high, highlighting the need to monitor water bodies with very low levels of pollutants and identify those requiring treatment.

Comprehensive Controller for Super Sonic Molecular Beam Gas Chromatograph Mass Spectrometer

This paper presents a new, comprehensive digital circuit used for the control of a novel gas chromatograph mass spectrometer (GC-MS) interface that is based on supersonic molecular beam (SMB). The circuit includes a Texas Instruments 150 MHz digital signal controller (DSC), high voltage amplifiers for 8 independent channels and 4 independent channels of high resolution pulse width modulation (PWM). The circuit, along with a sophisticated embedded program and a custom made personal computer (PC) application, control all aspects of the interface: smart filament emission-current stabilization, static and scanning mass-dependent ion-source voltages, transfer-line heater proportional integral differential (PID) controls with thermocouple feedbacks, on/off valves, relays and several peripheral device controls that enable the full operation of a turbo-molecular vacuum pump, and of gas flow and pressure controllers. All aspects of this comprehensive controller were successfully tested. The signal for the 450 Th ion (C32H66) for example increased by 123% which is a significant increase. It is obvious that correctly tuned dynamic voltages can guarantee the optimal signal for each mass.

Volatile Organic Compounds, Evaluation Methods and Processing Properties for Cooked Rice Flavor

Rice (Oryza sativa L.), as the main refined grain in China, has attracted much attention in terms of quality. Rice is usually consumed after cooking, and it is a commonly staple food. Nowdays, people's requirements for cooked rice focus more on the taste characteristics and quality. Furthermore, aroma is one of the primary sensory reference points, which is the most intuitive way for people to judge cooked rice. By integrating and analyzing the researches of cooked rice aroma identification in recent five years, this paper expounds the extraction and identification methods (sensory evaluation method, GC-MS, SPME, MOS sensors, electronic nose, etc.) of the flavor substances in cooked rice, as the processing methods and properties of cooked rice, and the volatile organic compounds of cooked rice under different conditions are summarized as well.

High separation performance of carbon dioxide-based poly(ether-carbonate) copolymer for gas chromatographic analyses

This work presents the investigation of a novel CO₂-based poly(ether-carbonate) copolymer, namely poly(propylene ether-carbonate)diol (PPCD), for gas chromatographic (GC) analyses. The PPCD column exhibited column efficiency of 4000 plates/m determined by naphthalene at 120 ℃ with the retention factor 6.23. Its separation performance was investigated by adopting a wide variety of analytes and isomers, including the isomer mixtures of alkanes, substituted benzene isomers with diverse groups, phenols and anilines, and the mixtures of organic solvents of high volatility, aliphatic amines and N-heterocycles. As a result, the PPCD column displayed distinctly higher resolving capability than the commercial columns described herein and achieved high column inertness towards acidic/basic analytes without involving any deactivation procedure. Additionally, it displayed excellent separation repeatability and reproducibility with the relative standard deviation (RSD) values less than 0.01% for within-day and in the range of 0.26% - 0.36% for between-day and 3.0% - 4.1% for between-column (n = 4). Further, the PPCD column (30 m) was used to GC-MS analysis of the lemongrass essential oil and resolved more components well than the indicated commercial columns, evidencing its outstanding separation performance for analyses of complex samples. Up to date, the CO₂-based poly(ether-carbonate) copolymers are not reported in the field of chromatography. This work demonstrates their promising future as a new type of selective and inert stationary phases for practical GC analyses.

Current Role of Mass Spectrometry in the Determination of Pesticide Residues in Food

The extensive use of pesticides represents a risk to human health. Consequently, legal frameworks have been established to ensure food safety, including control programs for pesticide residues. In this context, the performance of analytical methods acquires special relevance. Such methods are expected to be able to determine the largest number of compounds at trace concentration levels in complex food matrices, which represents a great analytical challenge. Technical advances in mass spectrometry (MS) have led to the development of more efficient analytical methods for the determination of pesticides. This review provides an overview of current analytical strategies applied in pesticide analysis, with a special focus on MS methods. Current targeted MS methods allow the simultaneous determination of hundreds of pesticides, whereas non-targeted MS methods are now applicable to the identification of pesticide metabolites and transformation products. New trends in pesticide analysis are also presented, including approaches for the simultaneous determination of pesticide residues and other food contaminants (i.e., mega-methods), or the recent application of techniques such as ion mobility–mass spectrometry (IM–MS) for this purpose.

Detection and toxicity modeling of anthraquinone dyes and chlorinated side products from a colored smoke pyrotechnic reaction

"Green" pyrotechnics seek to remove known environmental pollutants and health hazards from their formulations. This chemical engineering approach often focuses on maintaining performance effects upon replacement of objectionable ingredients, yet neglects the chemical products formed by the exothermic reaction. In this work, milligram quantities of a lab-scale pyrotechnic red smoke composition were functioned within a thermal probe for product identification by pyrolysis-gas chromatography-mass spectrometry. Thermally decomposed ingredients and new side product derivatives were identified at lower relative abundances to the intact organic dye (as the engineered sublimation product). Side products included chlorination of the organic dye donated by the chlorate oxidizer. Machine learning quantitative structure-activity relationship models computed impacts to health and environmental hazards. High to very high toxicities were predicted for inhalation, mutagenicity, developmental, and endocrine disruption for common military pyrotechnic dyes and their analogous chlorinated side products. These results underscore the need to revise objectives of "green" pyrotechnic engineering.

State-of-the-Art Research on Chemiresistive Gas Sensors in Korea: Emphasis on the Achievements of the Research Labs of Professors Hyoun Woo Kim and Sang Sub Kim

This review presents the results of cutting-edge research on chemiresistive gas sensors in Korea with a focus on the research activities of the laboratories of Professors Sang Sub Kim and Hyoun Woo Kim. The advances in the synthesis techniques and various strategies to enhance the gas-sensing performances of metal-oxide-, sulfide-, and polymer-based nanomaterials are described. In particular, the gas-sensing characteristics of different types of sensors reported in recent years, including core-shell, self-heated, irradiated, flexible, Si-based, glass, and metal-organic framework sensors, have been reviewed. The most crucial achievements include the optimization of shell thickness in core-shell gas sensors, decrease in applied voltage in self-heated gas sensors to less than 5 V, optimization of irradiation dose to achieve the highest response to gases, and the design of selective and highly flexible gas sensors-based WS2 nanosheets. The underlying sensing mechanisms are discussed in detail. In summary, this review provides an overview of the chemiresistive gas-sensing research activities led by the corresponding authors of this manuscript.

Structure Elucidation Using Gas Chromatography-Infrared Spectroscopy/Mass Spectrometry Supported by Quantum Chemical IR Spectrum Simulations

An improved strategy for compound identification incorporating gas chromatography hyphenated with Fourier transform infrared spectroscopy and mass spectroscopy (GC-FTIR/MS) is reported. (Over)reliance on MS may lead either to ambiguous identity or to incorrect identification of a compound. However, the MS result is useful to provide a cohort of possible compounds. The IR result for each tentative compound match was then simulated using molecular modeling, to provide functional group and isomer differentiation information, and then compared with the experimental FTIR result, offering identification based on both MS and IR. Several basis sets were evaluated for IR simulations; Def2-TZVPP was a suitable basis set and correlated well with experimental data. The approach was applied to industrial applications, confirming the isomers of 2,3-bis(thiosulfanyl)-but-2-enedinitrile, bromination products of 1-bromo-2,3-dimethylbenzene, and autoxidative degradation of phenyl-di-tert-butylphosphine.

Evaluation of a novel controlled-atmosphere flexible microtube plasma soft ionization source for the determination of BTEX in olive oil by headspace-gas chromatography/mass spectrometry

Although electron impact ionization (EI) remains the standard ionization source for GC-MS, it presents extensive fragmentation as its main limitation. The potential of a novel plasma-based soft ionization source named controlled-atmosphere flexible microtube plasma (CA-FμTP) has been evaluated in this work for the determination of monoaromatic volatile BTEX group (namely benzene, toluene, ethylbenzene, and o-, m- and p-xylenes) in olive oil, based on headspace technique. The obtained results show an attractive advantage over EI due to no fragmentation was observed. A nitrosated ion [M + NO]⁺ is obtained as the most abundant species. Thus, the BTEX mass spectrum identification can be carried out without major effort. In general, the sensitivity for CA-FμTP was comparable to those obtained by EI, achieving LODs ranged from 0.6 to 1.0 μg kg^-1. The potential usefulness of GC-CA-FμTP-MS for the detection of BTEX was demonstrated by analyzing olive oil samples and identifying traces of these compounds in one sample. Therefore, the proposed plasma-based soft ionization is suitable for BTEX analysis in fatty complex matrixes as olive oil.

Exploring 20 eV electron impact ionization in gas chromatography-tandem mass spectrometry for the determination of estrogenic compounds

In electron ionization mass spectrometry (MS), the generation of characteristic fragmentation patterns allows reliable and sensitive identification of compounds. However, loss or a less intense signal of the molecular ion (or more diagnostic ions) can often be observed, which can be detrimental for identification and/or sensitivity, even when MS/MS approaches are applied for quantification. The benefits of applying lower ionization energy (i.e., 20 eV compared to 70 eV) using a gas chromatography (GC) - tandem MS (MS/MS) instrument were investigated in the detection of three estrogenic compounds, namely estrone (E1), 17β-estradiol (E2), and 17α-ethynylestradiol (EE2), emerging aquatic pollutants included in the European Commission Watch List. As expected, the relative intensity of molecular ions (M^+.) or high-mass fragments closely related (M^+.-CH₃) increased significantly at 20 eV compared to 70 eV (from 4.6 % to 35.0 % for EE2, from 22.5 % to 87.3 % for E2, and from 76 % to 100 % for E1). This change in the spectrum profile led to an overall increase in the sensitivity of the compounds when detected using the multiple reaction monitoring mode. These results were compared with the instrumental limit of quantification obtained in liquid chromatography - MS/MS showing a limit of quantification of about 100-folds lower for GC-MS/MS and a completely neglectable matrix effect, thus posing the base for the development of a miniaturized sample preparation method (with an overall lower concentration factor) to achieve the challenging low limits of detection required by the EU regulation for estrogenic compounds.

Analytical Methods for the Determination of Neuroactive Steroids

Neuroactive steroids are a family of all steroid-based compounds, of both natural and synthetic origin, which can affect the nervous system functions. Their biosynthesis occurs directly in the nervous system (so-called neurosteroids) or in peripheral endocrine tissues (hormonal steroids). Steroid hormone levels may fluctuate due to physiological changes during life and various pathological conditions affecting individuals. A deeper understanding of neuroactive steroids' production, in addition to reliable monitoring of their levels in various biological matrices, may be useful in the prevention, diagnosis, monitoring, and treatment of some neurodegenerative and psychiatric diseases. The aim of this review is to highlight the most relevant methods currently available for analysis of neuroactive steroids, with an emphasis on immunoanalytical methods and gas, or liquid chromatography combined with mass spectrometry.