Periodate-assisted pulsed sonocatalysis of real textile wastewater in the presence of MgO nanoparticles: Response surface methodological optimization

Optimization of green and environmentally-benign synthesis of isoamyl acetate in the presence of ball-milled seashells by response surface methodology

Ball-milled seashells, as a nano-biocomposite catalyst and natural source of CaCO₃ in its aragonite microcrystalline form with fixed CO₂, was optimized for the synthesis of isoamyl acetate (3-methylbutyl ethanoate) by response surface methodology with a five-level three-factor rotatable circumscribed central composite design. The seashells nano-biocomposite has proved to be an excellent heterogeneous multifunctional catalyst for the green and environmentally-benign synthesis of isoamyl acetate from acetic acid and isoamyl alcohol under solvent-free conditions. A high yield of 91% was obtained under the following optimal conditions: molar ratio of alcohol: acetic acid (1:3.7), catalyst loading (15.7 mg), the reaction temperature (98 °C), and the reaction time (219 min). The outstanding advantages of this protocol are the use of an inexpensive, naturally occurring and easily prepared nano-biocomposite material having appropriate thermal stability and without any modifications using hazardous reagents, lower catalyst loading and reaction temperature, no use of corrosive Bronsted acids as well as toxic azeotropic solvents or water adsorbents, and simplicity of the procedure.

Investigation of CuCoFe-LDH as an efficient and stable catalyst for the degradation of acetaminophen in heterogeneous electro-Fenton system: Key operating parameters, mechanisms and pathways

Pharmaceuticals, as anthropogenic pollutants in a wide range of water sources, generally require specific treatment methods for degradation. A trimetallic layered double hydroxide (CuCoFe-LDH) was successfully fabricated by coprecipitation and applied as a novel heterogeneous electro-Fenton (EF) catalyst for the degradation of acetaminophen (ACT) from aqueous environments. The EF experiments showed that the CuCoFe-LDH/EF process achieved 100% of ACT degradation efficiency within 60 min at pH = 5, catalyst dosage of 0.50 g/L, current density of 10 mA/cm² and initial ACT concentration of 20 mg/L. An impressive (>80%) mineralization of ACT was obtained over a wide pH range (pH 3-9) after 180 min. Meanwhile, the role of ·OH and O₂^.- were certified by radical quenching experiments and electron paramagnetic resonance (EPR) analysis. Through mechanism exploration, the coexistence of Cu and Co on Fe-based LDHs can accelerate the interfacial electron transfer and promote the formation of the reactive oxygen species (ROS), thus facilitating the EF process. Furthermore, the degradation by-products and possible degradation pathways of ACT in the CuCoFe-LDH/EF process were proposed. The reusability test and the treatment of various typical organic pollutants experiments indicated that the CuCoFe-LDH/EF process has excellent stability and broad application prospects. This work provides a valuable reference for the treatment of pharmaceuticals by the heterogeneous EF process in a wide range of pH.

Promoting selective water decontamination via boosting activation of periodate by nanostructured Ru-supported Co3O4 catalysts

The superior catalytic efficiency of ruthenium (Ru)-based nanocomposites in advanced oxidation processes for water decontamination has attracted accumulating attention worldwide. However, rather limited knowledge is currently available regarding their roles in activating periodate (PI), an emerging oxidant with versatile environmental applications. This study firstly delineated that Ru-supported Co₃O₄ (Ru/Co₃O₄), a typical Ru-based nanomaterial, can efficiently accomplish PI activation to eliminate multiple organic micropollutants and inactivate different pathogenic bacteria. Almost all eight micropollutants can be completely removed within 2 min of Ru/Co₃O₄-PI oxidation except sulfamethoxazole (SMX), which was degraded ∼70 % at 2 min with 100 % mineralization after 10 min. The excellent catalytic performance was independent of PI dosages, initial pH, and coexisting water constituents, demonstrating its prominent capability as a selective oxidation strategy. Diverse lines of evidence indicated the dominant role of single oxygen in the Ru/Co₃O₄-PI system, which triggered the generation of five transformation products of SMX with reduced environmental risks. Concurrently, PI was stoichiometrically converted to the eco-friendly IO₃^-. Additionally, Ru/Co₃O₄-PI system achieved 6-log inactivation of different pathogenic bacteria within 1 min, implying the feasibility of rapid water disinfection. Overall, this work demonstrated the excellent promise of Ru-based composites in PI activation for highly efficient and selective water decontamination.

Emerging periodate-based oxidation technologies for water decontamination: A state-of-the-art mechanistic review and future perspectives

With the ever-increasing severity of the ongoing water crisis, it is of great significance to develop efficient, eco-friendly water treatment technologies. As an emerging oxidant in the advanced oxidation processes (AOPs), periodate (PI) has received worldwide attention owing to the advantages of superior stability, susceptible activation capability, and high efficiency for decontamination. This is the first review that conducts a comprehensive analysis of the mechanism, pollutant transformation pathway, toxicity evolution, barriers, and future directions of PI-based AOPs based on the scientific information and experimental data reported in recent years. The pollutant elimination in PI-based AOPs was mainly attributed to the in situ generate reactive oxygen species (e.g., ^•OH, O(³P), ¹O₂, and O₂^•-), reactive iodine species (e.g., IO₃^• and IO₄^•), and high-valent metal-oxo species with exceptionally high reactivity. These reactive species were derived from the PI activated by the external energy, metal activators, alkaline, freezing, hydroxylamine, H₂O_2, etc. It is noteworthy that direct electron transport could also dominate the decontamination in carbon-based catalyst/PI systems. Furthermore, PI was transformed to iodate (IO₃^-) stoichiometrically via an oxygen-atom transfer process in most PI-based AOPs systems. However, the production of I₂, I^-, and HOI was sometimes inevitable. Furthermore, the transformation pathway of typical micropollutants was clarified, and the in silico QSAR-based prediction results indicated that most transformation products retained biodegradation recalcitrance and multi-endpoint toxicity. The barriers faced by the PI-based AOPs were also clarified with potential solutions. Finally, future perspectives and research directions are highlighted based on the current state of PI-based AOPs. This review enhances our in-depth understanding of PI-based AOPs for pollutant elimination and identifies future research needs to focus on the reduction of toxic byproducts.

Photo-oxidative Decolorization of Brilliant Blue with AgNPs as an Activator in the Presence of K2S2O8 and NaBH4

The decolorization of brilliant blue (E133) in aqueous solution by K2S2O8 and NaBH4 with AgNPs as an activator was studied spectrophotometrically under normal laboratory conditions. Batch experiments were performed to investigate the effects of reaction time, initial dye concentration, activator concentration, solution pH, and temperature on the decolorization of E133. K2S2O8 and NaBH4 did not decolorize the dye E133 in the absence of AgNPs. The optimum dosage of AgNPs was 0.01 g/L, and 98% dye E133 degradation was observed with 3.75 mM K2S2O8 at 30 °C in ca. 60 min of reaction time. In the NaBH4/AgNPs system, only 60% dye degradation was observed for an identical reaction condition. The decolorization rate constant increases with the increase in concentrations of AgNPs, K2S2O8, NaBH4, and reaction temperature. The decolorization degree of the E133 responded linearly with K2S2O8 and NaBH4 concentrations. The existence of sulfate radicals (SO4 · -) and hydroxyl radicals (HO·) generated during the decolorization of E133 was identified by using ethanol and tertiary butyl alcohol as scavengers. Based on the E133 solution absorbance changes at 628 nm, the decolorization mechanism was proposed and discussed.

Use of biogenic copper nanoparticles synthesized from a native Escherichia sp. as photocatalysts for azo dye degradation and treatment of textile effluents

Textile wastewater contains a huge amount of azo dyes and heavy metals and catastrophically deteriorates the agricultural field by affecting its phyisco-chemical/biological and nutritional properties when directly drained to agricultural lands without any treatment. Recently, biogenic copper nanoparticles (CuNPs) have gained considerable attention for photocatalytic degradation of wastewater pollutants owing to their unique physico-chemical and biological properties, low cost and environmental sustainability. The current study reports the synthesis of CuNPs by a native copper-resistant bacterial strain Escherichia sp. SINT7 and evaluation of the photocatalytic activity of the biogenic CuNPs for azo dye degradation and treatment of textile effluents. Scanning electron microscopy and transmission electron microscopy revealed the spherical shape of biogenic CuNPs with particle size ranging from 22.33 to 39 nm. Moreover, X-ray diffraction data revealed that the CuNPs have spherical crystalline shapes with an average particle size of 28.55 nm. FTIR spectra showed the presence of coating proteins involved in the stabilization of nanomaterial. Azo dye degradation assays indicated that CuNPs decolorized congo red (97.07%), malachite green (90.55%), direct blue-1 (88.42%) and reactive black-5 (83.61%) at a dye concentration of 25 mg L^-1 after 5 h of sunlight exposure. However, at 100 mg L^-1 dye concentration, the degradation percentage was found to be 83.90%, 31.08%, 62.32% and 76.84% for congo red, malachite green, direct blue-1 and reactive black-5, respectively. Treatment of textile effluents with CuNPs resulted in a significant reduction in pH, electrical conductivity, turbidity, total suspended solids, total dissolved solids, hardness, chlorides and sulfates as compared to the non-treated samples. Thus, the promising dye detoxification and textile effluent recycling efficiency of biogenic CuNPs may lead to the development of eco-friendly and cost-efficient process for large-scale wastewater treatment.

Enhanced sonocatalytic performance of ZnTi nano-layered double hydroxide by substitution of Cu (II) cations

In this research, a series of CuZnTi-LDHs with different Cu²⁺/Zn²⁺ molar ratio were synthesized by co-precipitation method with the purpose of improving the sonocatalytic performance of ZnTi-LDH. All the LDH samples were synthesized by a facile co-precipitation process. The as-prepared LDHs were characterized by Powder X-ray diffraction (XRD), Field emission-scanning electron microscopy (FESEM), Transition electron microscopy (TEM), Brunauer-Emmelt-Teller (BET) analysis, and UV-visible diffuse reflectance spectroscopy (DRS) analysis. The results showed that Cu²⁺ substitution can significantly enhance the sonocatalytic properties of ZnTi-LDH. The Methylene blue degradation percentage over ZnTi-LDH reached 30% in 90 min, whilst this percentage reaches 71% over CuZnTi-LDH (1:1). The role of the Cu²⁺ incorporation on the observed enhancement in sonocatalytic performance was revealed by investigating the effect of radical scavengers on degradation efficiency and DRS spectra of ZnTi-LDH and CuZnTi-LDH (1:1). Benzoquinone (BQ), ammonium oxalate and tert-Bu lead to 22.5%, 53.5% and 74.6% decrease in degradation percentage by CuZnTi-LDH (1:1). However, the degradation efficiency showed 16.6%, 3.3% and 63.3% reduction in the presence of BQ, ammonium oxalate and tert-Bu respectively, in dye degradation by ZnTi-LDH. DRS spectra demonstrated that the band gap of the LDH decreases by Cu²⁺ substitution. The effect of operational parameters on sonodegradation was investigated as well. The kinetics of sonodegradation reaction obeyed the first order reaction kinetics with R² of 0.95.

Effective degradation of sulfide ions and organic sulfides in cavitation-based advanced oxidation processes (AOPs)

The paper presents the results of investigations on the effectiveness and reaction rate constants of the oxidation of sulfide ions and organic sulfides in real industrial effluents from the production of bitumens (2000 mg S^2- L^-1) using hydrodynamic and acoustic cavitation. The content of the effluents was analysed in terms carbon disulfide, dimethyl sulfide, and di-tert-butyl disulfide concentration. A possibility of complete oxidation of sulfides by cavitation alone as well as by its combination with external oxidants such as hydrogen peroxide, ozone or peroxone was demonstrated. The oxidation time for the most effective processes is as little as 15 min. Due to the presence of sulfide ions, the effluents from the production of bitumens were oxidized at a strongly alkaline pH. The results of this study reveal the advantage of performing advanced oxidation processes (AOPs) at a basic pH. The effective degradation of sulfide ions enables performance of further degradation of organic contaminants at an acidic pH, ensuring high efficiency of treatment based, for example, on the Fenton reaction without the risk of release of hydrogen sulfide to the atmosphere. The results of this research are applicable to all kinds of caustic effluents for which the lack of possibility of pH adjustment limits their efficient treatment.

Template-free microspheres decorated with Cu-Fe-NLDH for catalytic removal of gentamicin in heterogeneous electro-Fenton process

Nano-layered double hydroxide (NLDH) decorated with Fe and Cu was applied as a novel heterogeneous catalyst for catalytic degradation of gentamicin by the electro-Fenton (EF) process. The EF process was equipped with graphite plate under aeration to electrochemically generate hydrogen peroxide in the solution. The characterization analyses confirmed the suitable structure of as-synthesized Cu-Fe-NLDH to be acted as catalyst for treating the target pollutant. The comparative study showed the highest removal efficiency of 91.3% when the Cu-Fe-NLDH-equipped EF process was applied in comparison with the Fenton (50%) and the electro-oxidation alone (25.6%). The acidic pHs favored the degradation of gentamicin. Increasing the current resulted in the enhanced degradation of gentamicin, while the excessive electrolyte concentration (0.1 mol/L) and catalyst dosage (1.5 g/L) led to the tangible drop in the reactor performance. At a specified reaction time, the injection of O₃ gas enhanced the efficiency of the Cu-Fe-NLDH-equipped EF process. The presence of ethanol led to more suppressing effect than benzoquinone, indicating the dominant role of OH radical in the degradation of gentamicin compared with other free radical species such as O₂^- radical. Only 10% drop in the degradation efficiency of gentamicin was observed within 10 operational runs. The mineralization efficiency of about 77% was achieved after 300 min in terms of chemical oxygen demand (COD) removal. The intermediate byproducts generated during the destructive removal of gentamicin were also identified.

Sonocatalytic degradation of tetracycline antibiotic using zinc oxide nanostructures loaded on nano-cellulose from waste straw as nanosonocatalyst

The aim of the present investigation was the combination of ZnO nanostructures with nano-cellulose (NC) for the efficient degradation of tetracycline (TC) antibiotic under ultrasonic irradiation. The removal efficiency of 12.8% was obtained by the sole use of ultrasound (US), while the removal efficiency increased up to 70% by the US/ZnO treatment process. Due to the integration of ZnO nanostructures with NC, the removal efficiency of 87.6% was obtained within 45 min. The removal efficiency substantially decreased in the presence of tert-butyl alcohol (more than 25% reduction), indicating that ^radOH-mediation oxidation is responsible for the degradation of TC molecules. Peroxymonosulfate (PMS) led to the most enhancing effect on the removal of TC among percarbonate, persulfate and periodate ions. The addition of PMS caused the degradation efficiency of 96.4% within the short contact time of 15 min. The bio-toxicity examination on the basis of inhibition test conducted on activated sludge revealed diminishing the oxygen consumption inhibition percent [I_OUR (%)] from 33.6 to 22.1% during the US/ZnO/NC process. Consequently, the utilization of the US/ZnO/NC process can convert TC molecules to less toxic compounds. However, longer reaction time is required for complete conversion into non-toxic substances.

Ultrasound assisted preparation, characterization and adsorption study of ternary chitosan-ZnO-TiO2 nanocomposite: Advantage over conventional method

In the present work, the synthesis of ternary chitosan/zinc oxide/titanium dioxide (CTS-ZnO-TiO₂) nanocomposite was carried out with the use of mechanical stirring (conventional) and ultrasound assisted method. The characterization of prepared CTS-ZnO-TiO₂ adsorbent was carried out using XRD, TEM, FTIR and the results of these analysis methods proved the successful preparation of ternary nanocomposite. Crystal violet (CV) dye was used as a pollutant to observe the adsorption ability of the prepared nanocomposite and the nanocomposite prepared by ultrasonic-assisted method proved to be a better adsorbent. The CV dye adsorption was significant for CTS-ZnO-TiO₂ nanocomposite synthesized with the use of ultrasound assisted method compared to that prepared by conventional method. It is due to the physical effects of the ultrasonic irradiations due to which formation of finely dispersed nanocomposite takes place than that by conventional method. For batch adsorption the effect of various operating parameters such as initial dye concentration, time, temperature and adsorbent dose has been evaluated. The obtained data were processed using isotherm models, adsorption kinetics and the thermodynamic behavior of the cationic dye adsorption was also studied. The isotherm data was correlated reasonably well by the Temkin adsorption isotherm. Pseudo-second-order kinetic model provided a better correlation for the experimental data compared to pseudo first order, Elovich model and power function kinetics model. Thermodynamic parameters for adsorption indicated that the dye adsorption was spontaneous and endothermic in nature.

Enhancement of ultrasound-assisted degradation of Eosin B in the presence of nanoparticles of ZnO as sonocatalyst

In this research, ZnO nanoparticles, as a sonocatalyst for degradation of Eosin B dye under ultrasonic irradiation, were synthesized. Various experimental conditions (ultrasound irradiation power: 50-250 W, ultrasound irradiation time: 10-70 min, catalyst dosage: 1-3 g/L and initial dye concentration: 5-25 mg/L), using ZnO nanoparticles were investigated in order to find the optimal condition for the degradation of Eosin B. The crystalline and grain size of samples were obtained using X-Ray Diffraction (XRD) and Transmission Electron Microscopy (TEM), 15 and 30 nm, respectively. The nanoparticles structure was observed in the form of hexagonal. The band-gap of the prepared nanoparticles was measured as 2.9 eV which is appropriate for sonodegradation process under ultrasonic irradiation. Results demonstrated that Eosin B degradation efficiency was enhanced considerably in sonicated samples compared to non-sonicated ones. The experiments were analyzed via response surface methodology (RSM) based on central composite design (CCD). Analysis of variance (ANOVA) confirmed a good reliability of quadratic response surface model for predicting the sonocatalytic efficiency at various operational parameters (R² = 0.9918 and Adjusted R² = 0.9841). Results indicated that increasing the ultrasound power and time led to enhancement of Eosin B removal efficiency, while increasing the dye concentration caused to its decreasing. The degradation of dye, increased by enhancement of the catalyst dosage, where in the specified value (2.17 g/L) it began to decrease. The optimization of the process showed the maximum sonocatalyst degradation of 93.46% at irradiation power, irradiation time, catalyst dosage and dye concentration of 250 W, 70 min, 2.17 g/L and 5.08 mg/L, respectively. Kinetic studies showed that the sonodegradation of Eosin B corresponds well to first-order reaction.

Implementation of martite nanoparticles prepared through planetary ball milling as a heterogeneous activator of oxone for degradation of tetracycline antibiotic: Ultrasound and peroxy-enhancement

The aim of the present study was to employ martite nanoparticles synthesized through planetary ball milling instead of conventional sources of iron for the activation of Oxone in order to decompose tetracycline (TC) antibiotic in the aquatic phase. Accordingly, martite nanoparticles-activated Oxone exhibited a remarkable improvement in degrading TC molecules up to 87%. The results indicated an increased decomposition rate of TC with increasing Oxone concentration, martite nanoparticles dosage, and initial pH. In the absence of ultrasound, the decomposition rate of TC was 0.0481 min^-1 within 30 min, while the implementation of ultrasound at 320 W and addition of hydrogen peroxide at 40 mM led to increase in the decomposition rate up to 0.0770 and 0.0907 min^-1, respectively. The presence of carbonate and even persulfate ions suppressed the decomposition rate. Inversely, the addition of chloride and carbon tetrachloride enhanced the reactor performance in terms of TC degradation. Within four consecutive experimental runs, only 10.8% was dropped in the decomposition rate, indicating the appropriate reusability potential of martite nanoparticles. The results confirmed the appropriate ability of the treatment process in degrading and mineralizing the target pollutant but a longer exposure time is required for an efficient mineralization.

Implementation of continuously electro-generated Fe3O4 nanoparticles for activation of persulfate to decompose amoxicillin antibiotic in aquatic media: UV254 and ultrasound intensification

In the present investigation, the treatment of amoxicillin (AMX)-polluted water by the activated persulfate (PS) was considered. As a novel research, continuously electro-generated magnetite (Fe₃O₄) nanoparticles (CEMNPs) were utilized as the activator of PS in an electrochemical medium. The PS/CEMNPs displayed a remarkable enhancement in the decomposition of AMX molecules up to 72.6% compared with lonely PS (24.8%) and CEMNPs (13.4%). On the basis of pseudo-first order reaction rate constants, the synergy percent of about 70% was achieved due to the combination of PS with CEMNPs. The adverse influence of free radical-scavenging compounds on the efficiency of the PS/CEMNPs process was in the following order: carbonate < chloride < tert-butyl alcohol < ethanol. Overall, these results proved the main role of free radical species in degrading AMX. The implementation of ultrasound (US) enhanced the performance of the PS/CEMNPs process. Nevertheless, the highest degradation efficiency of about 94% was achieved when UV₂₅₄ lamp was joined the PS/CEMNPs system. Under UV₂₅₄ and US irradiation, the results showed significant potential of the PS/CEMNPs process for degrading AMX antibiotic and generating low toxic effluent based on the activated sludge inhibition test. However, more time is needed to achieve the acceptable mineralization.

Facile approach for synthesis of stable, efficient, and recyclable ZnO through pulsed sonication and its application for degradation of recalcitrant azo dyes in wastewater

In the present study, the ultrasound in pulsed mode was used as a part of an advanced oxidation method. The influence of the pulsed ultrasound mode for the preparation of the zinc oxide (ZnO) wurtzite nanoparticle was investigated. The catalysts synthesized were analysed using SEM, TEM, EDAX, BET surface area, XRD, and DRS to study their morphological and structural characterizations. The ZnO nanoparticles exhibited a highly hexagonal structure from pulsed sonication synthesis route. The efficiency of the decolourization of the reactive red 4 (RR4) dye was studied under different operation parameters such as dye concentration, initial solution pH, oxidant (e.g., H2O2) concentration, and catalyst loading. The hybrid combined process of pulsed sonolysis, pH (4.0), H2O2 (17.64 mmol), and catalyst (0.35 g/L) achieved 97% degradation and 87.5% chemical oxygen demand removal in about 20 min of reaction time. The cyclic degradation studies of RR4 removal with 0.35 g/L of ZnO showed the reusability of catalyst up to the fifth removal cycle with negligible loss in the catalytic performance. GC–MS study, used for the detection of the RR4 intermediates, revealed the oxidation–reduction reaction by the reactive radicals proceeded via the reductive cleavage of the azo bonds. The studied process, based on the pulsed ultrasound, is found to be effective for the degradation of RR4 dye.

Pilot-scale study on catalytic ozonation of bio-treated dyeing and finishing wastewater using recycled waste iron shavings as a catalyst

A pilot scale reactor with an effective volume of 2.93 m³ was built in-situ and run in both batch and continuous modes to investigate the removal for organic pollutants in bio-treated dyeing and finishing wastewater by heterogeneous catalytic ozonation under neutral pH with waste iron shavings as a catalyst. Experimental results showed that both running modes were able to reduce the chemical oxygen demand (COD) from 132–148 mg/L to a level below the discharge criteria (<80 mg/L) within 15–30 mins under several conditions. Specifically, significantly organic removal was observed with COD, soluble COD (sCOD) and dissolved organic carbon (DOC) decreased from the initial 165, 93 and 76 mg/L to 54, 28 and 16 mg/L respectively, when treated by 10.2 g-O₃/min of ozone dosage at a hydraulic retention time of 30 mins under continuous mode. 80% proteins and 85% polysaccharides were removed with a decrease in their contribution to sCOD from 69% to 43%. Mineralization as well as conversion of high molecular organic compounds was observed through Gas Chromatography-Mass Spectrometer (GC-MS) & Liquid Chromatography-Mass Spectrometer (LC-MS) analysis, which led to a decrease of inhibitory effect from 29% to 25%, suggesting a reduction in the acute toxicity.

Decomposition of ibuprofen in water via an electrochemical process with nano-sized carbon black-coated carbon cloth as oxygen-permeable cathode integrated with ultrasound

The main aim of the present investigation was the treatment of ibuprofen (IBP)-polluted aquatic phase using a novel oxygen-permeable cathode (OPC)-equipped electrochemical process (ECP) integrated with ultrasound (US). According to kinetic modeling, the decomposition rate of IBP by the integrated process was 3.2 × 10^-2 min^-1 which was significant in comparison with the OPC-equipped ECP (1.4 × 10^-2 min^-1) and US alone (2.4 × 10^-3 min^-1). Increasing the current resulted in the enhanced generation of H₂O₂ and consequently, improved the degradation of IBP in the solution. Excessive concentrations of Na₂SO₄ as supporting electrolyte led to no significant enhancement in the reactor efficiency. At initial IBP concentration of 1 mg L^-1, complete removal of IBP with reaction rate of 1.7 × 10^-1 min^-1 was happened within a short reaction time of 30 min. The pulse mode of US led to more than 10% increase in the removal efficiency compared with the normal mode. The presence of scavenging compound of methanol caused the highest drop in the efficiency of the integrated treatment process, indicating the substantial role of free hydroxyl radicals in the degradation of IBP. Intermediate byproducts generated in the solution during the decomposition were also identified and interpreted.

Electronic and vibrational second hyperpolarizabilities of (MgO)n clusters

In this work, we report results for the static second hyperpolarizability of magnesium oxide clusters including electronic and vibrational contributions. The comparison between second-order Møller-Plesset (MP2) perturbation theory and coupled cluster results to the electronic contribution points out that MP2 is a suitable method to compute this property. When computed at the MP2 level, the electronic contribution per atom converges to approximately 5000 a.u. Vibrational corrections were computed at the MP2 level through the perturbation theoretical method of Bishop and Kirtman. Results obtained showed that the term [α²]^0,0 represents around 20% of the electronic counterpart while the term [μβ]^0,0 is comparable to it. Modes that contribute significantly to [α²]^0,0 are those in which all or part of the bond lengths simultaneously increase and decrease, leading to large polarizability derivatives. In turn, modes that provide relevant contributions to [μβ]^0,0 are those in which oxygen anions move in opposite directions to the magnesium cations yielding large derivatives of the dipole moment and first hyperpolarizability.

Ultrasound-assisted Fenton process using siderite nanoparticles prepared via planetary ball milling for removal of reactive yellow 81 in aqueous phase

Nano-sized siderite was used as catalyst for the heterogeneous Fenton process combined with ultrasonic irradiation to degrade reactive yellow 81 (RY-81) in the aqueous phase. As the most efficient process, nano-sized siderite prepared via ball milling was chosen to carry out the experiments. 6h milled siderite at initial pH of 3.0 led to the highest removal efficiency of 92.09% within the reaction time of 30min. At a short reaction time of 20min, increasing siderite nanoparticles dosage from 0.3 to 0.75g/L resulted in increasing removal efficiency from 49.82 to 79.86%, respectively, while further increase in the dosage caused a substantial decrease in the efficiency. In the case of the effect of solute concentration, increasing the dye up to 400mg/L led to a significant decrease in the removal efficiency (65.77%). The presence of 0.01M Na₂CO₃ and C₂H₅OH significantly diminished the decolorization efficiency of RY-81 (<10%) with initial concentration of 100mg/L. The intermediates produced during the treatment process were also identified using GC-MS analysis. This research suggested that ball milled siderite is a potential catalyst for the efficient decolorization of textile effluents via ultrasound-assisted Fenton process.

Enhanced sonocatalysis of textile wastewater using bentonite-supported ZnO nanoparticles: Response surface methodological approach

The scope of this study was the use of bentonite as the carrier of ZnO nanoparticles for enhancing the sonocatalytic decolorization of Basic Red 46 (BR46) in the aqueous phase. The results demonstrated the higher sonocatalytic activity of bentonite-supported ZnO nanoparticles (BSZNs) in comparison with the suspended ZnO nanoparticles (SZNs). The particle size of BSZNs (5-40 nm) was lower than that of SZNs (20-120 nm). Due to the immobilization of ZnO nanoparticles, a specific surface area of 80.6 m(2)/g was obtained for the BSZNs, which was higher than the specific surface area of the raw bentonite (42.2 m(2)/g). Optimization of the process via response surface methodology (RSM) based on central composite design (CCD) showed the maximum sonocatalytic decolorization efficiency (%) of 89.92% in which the initial dye concentration, the ZnO/bentonite ratio, the sonocatalyst dosage, and the initial pH were 6 mg/L, 0.3, 2.5 g/L and 9, respectively. The byproducts generated during the sonocatalysis of BR46 over BSZNs were identified using gas chromatography-mass spectrometry (GC-MS) analysis. From an application viewpoint, the sonocatalysis of real textile wastewater resulted in a COD removal efficiency (%) of about 44% within a reaction time of 150 min.