Inactivation of the waterborne marine pathogen Vibrio alginolyticus by photo-chemical processes driven by UV-A, UV-B, or UV-C LED combined with H2O2 or HSO5. Water Res 2023;232:119686. [PMID: 36764105 DOI: 10.1016/j.watres.2023.119686]

Investigating the impact of organic matter on Vibrio parahaemolyticus inactivation in aquaculture water by UV-LED system

Ultraviolet (UV) irradiation becomes a promising technology in inactivating pathogenic microbes, but the compositional change of organics and its consequence of inactivation need further study in raw water during UV light-emitting diode (UV-LED) irradiation. Herein, the bench-scale study aimed at evaluating the effect of organic fractions isolated from shrimp-farming water on the inactivation efficiency of Vibrio parahaemolyticus using UV-LED process at wavelengths of 265 nm, 280 nm, and combined wavelengths. The lowest required UV fluence (4.06 mJ/cm2) for 3-log inactivation was attained with UV-LED 280 nm. After UV irradiation the changes in elemental compositions of organic compounds, based on H/C and O/C ratios, were small. This is probably due to low UV exposure and UV resistant structure of organic constituents, predominantly lipid-like compounds. Contrarily, fluorescent spectroscopic analysis that showed degradation of protein-like substances by UV irradiation. In addition, the significant declines in the number of chemical formulas in organic compounds were identified through non-target screening using orbitrap mass spectrometry, suggesting degradation and amalgamation into new compounds. The presence of organic compounds did not profoundly affect inactivation efficiency at applying a minimum required fluence or greater. This study highlights the potential of UV-LED irradiation, particularly at 280 nm, for efficient inactivation of V. parahaemolyticus and subsequent molecular structure alteration of organic matter after UV irradiation.

Peroxide Disinfection of Vesicle-Cloaked Murine Norovirus Clusters: Vesicle Membranes Protect Viruses from Inactivation

Vesicle-cloaked virus clusters, also known as viral vesicles, exhibit higher infectivity than free viruses and demonstrate persistence in the environment as well as resilience against disinfection. These emerging pathogens represent significant, yet often underestimated, health risks. Our study investigated peroxide disinfection of murine norovirus vesicles, a surrogate for human norovirus vesicles, and elucidated disinfection mechanisms. Peracetic acid, a neutral peroxide, rapidly inactivated murine norovirus vesicles. In contrast, negatively charged peroxides, i.e., peracetate and peroxymonosulfate, exhibited restricted effectiveness in inactivating murine noroviruses within vesicles. The largely intact viruses cloaked within vesicles remained infectious and retained their ability to replicate upon vesicle lysis triggered by mechanical forces, enzymatic activity, or chemical reactions following disinfection. Peroxides primarily targeted vesicle/viral proteins, particularly amino acid residues such as cysteine and methionine, without affecting the viral ORF2 gene fragment or vesicle structures. Disruption of viral internalization, rather than binding, plays a key role in infectivity loss. This work highlights the protective role of vesicle membranes and emphasizes the need for innovative disinfection approaches to effectively target viruses cloaked within vesicles.

Synergistic effects of a sequential recirculation electrochemical system combined with low-cost UV-LEDs on the gram-negative bacteria inactivation

In this work, an electrochemical system combined with low-cost UV-LEDs was implemented for the inactivation of Escherichia coli and Pseudomonas aeruginosa. The individual elimination of these bacteria was followed by plate counting and flow cytometry, as complementary techniques to establish the cell inactivation and non-viability, respectively. The contribution of the different parts of the disinfection system (anode, cathode, and light) was determined. In addition, the efficiency of the UV-LEDs/GDE/DSA system in the disinfection of an irrigation water sample was studied. It was found that the combination of the electrochemical system with UV-LEDs was highly synergistic (φ > 7), having low electric energy consumptions per order of magnitude (EEO: 1.13 × 10-2 and 1.55 × 10-2 kWh/m3 order). Moreover, some differences in the inactivation kinetics and synergy between E. coli and P. aeruginosa were observed and linked to the structural/morphological characteristics of the two bacteria. Remarkably, the electrochemical system combined with low-cost UV-LEDs inactivated both target microorganisms after only 2 min of treatment. The flow cytometry analyses evidenced the damage to the cell membrane of the bacteria by the simultaneous and synergistic action of the electrogenerated H2O2 and active chlorine species (ACS), plus the attacks of photo-generated reactive oxygen species. This synergistic combination in the UV-LEDs/GDE/DSA system demonstrated remarkable efficiency in the disinfection of an irrigation water sample, achieving the elimination of culturable bacteria in 45 min of treatment. The results of this research demonstrated the capacity and great potential of an easy combination of electrochemistry with UV-LEDs as an alternative system for the elimination of gram-negative bacteria in water.

Selective elimination of organic pollutants and analysis of effects and novel mechanisms of aged microplastics on wavelength-dependent UV-LED/H2O2 system

The selective removal of organic pollutants and potential impact of aged microplastics (MPs) as emerging pollutants in wavelength-dependent UV-LED/H2O2 system are not fully understood. This study found that cefalexin (CFX) degradation efficiency in UV-LED alone system was highly correlated with its UV molar absorbance (R2=0.994), while in UV-LED/H2O2 system, it was correlated with ·OH yield (R2=0.991) across various wavelengths. Quantitative structure-activity relationship (QSAR) analysis showed selective degradation of six pollutants based on their e--donating capabilities (R2=0.748-0.916). The coexistence of aged MPs, introducing C-O/C=O groups and rearranging their surface e-, potentially affected the elimination efficiency of CFX. Aged polystyrene (PS) decreased the degradation efficiency of CFX by shorting the O-O bond length (lO-O) in H2O2 and capturing e- from H2O2, whereas aged polyethylene (PE), polypropylene (PP) and polyvinyl chloride (PVC) had negligible effects as the lO-O elongation balanced the e--donating effect of H2O2. Additionally, phenol released from aged PS, with strong nucleophilicity, competing with CFX for ·OH, further decreasing CFX degradation efficiency. This study provides valuable insights into organic pollutant selective removal and reveals a novel inhibitory mechanism of aged PS on the performance of UV-LED/H2O2 technology.

Biofilm formation by Listeria monocytogenes from the meat processing industry environment and the use of different combinations of detergents, sanitizers, and UV-A radiation to control this microorganism in planktonic and sessile forms

This study aimed to evaluate the ability of biofilm formation by L. monocytogenes from the meat processing industry environment, as well as the use of different combinations of detergents, sanitizers, and UV-A radiation in the control of this microorganism in the planktonic and sessile forms. Four L. monocytogenes isolates were evaluated and showed moderate ability to form biofilm, as well as carried genes related to biofilm production (agrB, agrD, prfA, actA, cheA, cheY, flaA, sigB), and genes related to tolerance to sanitizers (lde and qacH). The biofilm-forming isolates of L. monocytogenes were susceptible to quaternary ammonium compound (QAC) and peracetic acid (PA) in planktonic form, with minimum inhibitory concentrations of 125 and 75 ppm, respectively, for contact times of 10 and 5 min. These concentrations are lower than those recommended by the manufacturers, which are at least 200 and 300 ppm for QAC and PA, respectively. Biofilms of L. monocytogenes formed from a pool of isolates on stainless steel and polyurethane coupons were subjected to 14 treatments involving acid and enzymatic detergents, QAC and PA sanitizers, and UV-A radiation at varying concentrations and contact times. All treatments reduced L. monocytogenes counts in the biofilm, indicating that the tested detergents, sanitizers, and UV-A radiation exhibited antimicrobial activity against biofilms on both surface types. Notably, the biofilm formed on polyurethane showed greater tolerance to the evaluated compounds than the biofilm on stainless steel, likely due to the material's surface facilitating faster microbial colonization and the development of a more complex structure, as observed by scanning electron microscopy. Listeria monocytogenes isolates from the meat processing industry carry genes associated with biofilm production and can form biofilms on both stainless steel and polyurethane surfaces, which may contribute to their persistence within meat processing lines. Despite carrying sanitizer tolerance genes, QAC and PA effectively controlled these microorganisms in their planktonic form. However, combinations of detergent (AC and ENZ) with sanitizers (QAC and PA) at minimum concentrations of 125 ppm and 300 ppm, respectively, were the most effective.

Photodynamic activation of phytochemical-antibiotic combinations for combatting Staphylococcus aureus from acute wound infections

Staphylococcus aureus is characterized by its high resistance to conventional antibiotics, particularly methicillin-resistant (MRSA) strains, making it a predominant pathogen in acute and chronic wound infections. The persistence of acute S. aureus wound infections poses a threat by increasing the incidence of their chronicity. This study investigated the potential of photodynamic activation using phytochemical-antibiotic combinations to eliminate S. aureus under conditions representative of acute wound infections, aiming to mitigate the risk of chronicity. The strategy applied takes advantage of the promising antibacterial and photosensitising properties of phytochemicals, and their ability to act as antibiotic adjuvants. The antibacterial activity of selected phytochemicals (berberine, curcumin, farnesol, gallic acid, and quercetin; 6.25-1000 μg/mL) and antibiotics (ciprofloxacin, tetracycline, fusidic acid, oxacillin, gentamicin, mupirocin, methicillin, and tobramycin; 0.0625-1024 μg/mL) was screened individually and in combination against two S. aureus clinical strains (methicillin-resistant and -susceptible-MRSA and MSSA). The photodynamic activity of the phytochemicals was assessed using a light-emitting diode (LED) system with blue (420 nm) or UV-A (365 nm) variants, at 30 mW/cm2 (light doses of 9, 18, 27 J/cm2) and 5.5 mW/cm2 (light doses of 1.5, 3.3 and 5.0 J/cm2), respectively. Notably, all phytochemicals restored antibiotic activity, with 9 and 13 combinations exhibiting potentiating effects on MSSA and MRSA, respectively. Photodynamic activation with blue light (420 nm) resulted in an 8- to 80-fold reduction in the bactericidal concentration of berberine against MSSA and MRSA, while curcumin caused 80-fold reduction for both strains at the light dose of 18 J/cm2. Berberine and curcumin-antibiotic combinations when subjected to photodynamic activation (420 nm light, 10 min, 18 J/cm2) reduced S. aureus culturability by ≈9 log CFU/mL. These combinations lowered the bactericidal concentration of antibiotics, achieving a 2048-fold reduction for gentamicin and 512-fold reduction for tobramycin. Overall, the dual approach involving antimicrobial photodynamic inactivation and selected phytochemical-antibiotic combinations demonstrated a synergistic effect, drastically reducing the culturability of S. aureus and restoring the activity of gentamicin and tobramycin.

The loading of Fe ions on N-doped carbon nanosheets to boost photocatalytic cascade for water disinfection

The pervasive presence of pathogenic bacteria in water environment poses a serious threat to public health. Here, a photocatalytic cascade was developed to reveal great water disinfection. Firstly, N-doped carbon nanosheets (N-CNSs) about 30-50 nm in size were synthesized by a hydrothermal strategy. It revealed wide-spectrum photocatalysis for H2O2 generation via a typical two-step single-electron process. A Fenton agent (Fe ion) was loaded, N-CNSs-Fe can in-situ convert photocatalytic H2O2 into ·OH with high oxidation potential. Moreover, its Fenton active is three times greater than pure Fe2+ owing to electron enrichment from N-CNSs to Fe for Fe3+/Fe2+ cycle. Further investigation displayed that Fe loading also could decrease bad gap and promote charge separation to boost photocatalysis. In addition, N-CNSs-Fe possesses positive surface potential to exhibit strong interaction with negative bacteria, facilitating the capture. Therefore, the nanocomposite can effectively inactivate E. coli with a lethality rate of 99.7 % under stimulated sunlight irradiation. In addition, it also was employed to treat a complex lake water sample, revealing great antibacterial (95.1 %) and dye-decolored (92.3 %) efficiency at the same time. With novel biocompatibility and antibacterial ability, N-CNSs-Fe possessed great potential for water disinfection.

Kinetics of inactivation of bacteria responsible for infections in hospitals using UV-LED

Controlling the microbial load in the environment is crucial to prevent the spread of organisms. The continuous spread of nosocomial infections in hospital facilities and the emergence of the coronavirus (COVID-19) highlighted the importance of disinfection processes in health safety. This work aimed to evaluate the effectiveness of LED-based disinfection lamps on bacteria from the ESKAPEE group and virus phage in vitro inactivation to be applied in hospital environments and health facilities disinfection. This study evaluated the effect of different UV wavelengths (275 nm, 280 nm (UVC), 310 nm (UVB) and 340 nm (UVA)) on the disinfection process of various microbial indicators including E. coli, S. aureus, P. aeruginosa, B. subtilis and Bacteriophage lambda DSM 4499. Exposure time (5 min-30 min), exposure distance (0.25 m and 0.5 m) and surface materials (glass, steel, and polished wood) were evaluated on the disinfection efficiency. Furthermore, the study determined the recovery capacity of each species after UV damage. UVC-LED lamps could inactivate 99.99 % of microbial indicators after 20 min exposures at a 0.5 m distance. The exposure time needed to completely inactivate E. coli, S. aureus, P. aeruginosa, B. subtilis and Bacteriophage lambda DSM 4499 can be decreased by reducing the exposure distance. UVB-LED and UVA-LED lamps were not able to promote a log reduction of 4 and were not effective on B. subtilis or bacteriophage lambda DSM 4499 inactivation. Thus, only UVC-LED lamps were tested on the decontamination of different surface materials, which was successful. P. aeruginosa showed the ability to recover from UV damage, but its inactivation rate remains 99.99 %, and spores from B. subtilis were not completely inactivated. Nevertheless, the inactivation rate of these indicators remained at 99.99 % with 24 h incubation after UVC irradiation. UVC-LED lamps emitting 280 nm were the most indicated to disinfect surfaces from microorganisms usually found in hospital environments.

Dielectric barrier discharge plasma promotes disinfection-residual-bacteria inactivation via electric field and reactive species

Traditional disinfection processes face significant challenges such as health and ecological risks associated with disinfection-residual-bacteria due to their single mechanism of action. Development of new disinfection processes with composite mechanisms is therefore urgently needed. In this study, we employed liquid ground-electrode dielectric barrier discharge (lgDBD) to achieve synergistic sterilization through electric field electroporation and reactive species oxidation. At a voltage of 12 kV, Pseudomonas fluorescens (ultraviolet and ozone-resistant) and Bacillus subtilis (chlorine-resistant) were completely inactivated within 8 and 6 min, respectively, surpassing a 7.0-log reduction. The lgDBD process showed good disinfection performance across a wide range of pH values and different practical water samples. Staining experiments suggest that cellular membrane damage contributes to this inactivation. In addition, we used a two-dimensional parallel streamer solver with kinetics code to fashion a representative model of the basic discharge unit, and discovered the presence of a persistent electric field during the discharge process with a peak value of 2.86 × 106 V/m. Plasma discharge generates excited state species such as O(1D) and N2(C3Πu), and further forms reactive oxygen and nitrogen species at the gas-liquid interface. The physical process, which is driven by electric field-induced cell membrane electroporation, synergizes with the bactericidal effects of reactive oxygen and nitrogen species to provide effective disinfection. Adopting the lgDBD process enhances sterilization efficiency and adaptability, underscoring its potential to revolutionize physicochemical synergistic disinfection practices.

Unlocking the Potential of Nanobubbles: Achieving Exceptional Gas Efficiency in Electrogeneration of Hydrogen Peroxide

The electrogeneration of hydrogen peroxide (H2 O2 ) via the oxygen reduction reaction is a crucial process for advanced water treatment technologies. While significant effort is being devoted to developing highly reactive materials, gas provision systems used in these processes are receiving less attention. Here, using oxygen nanobubbles to improve the gas efficiency of the electrogeneration of H2 O2 is proposed. Aeration with nanobubbles is compared to aeration with macrobubbles under an identical experimental set-up, with nanobubbles showing a much higher gas-liquid volumetric mass transfer coefficient (KL a) of 2.6 × 10-2 min-1 compared to 2.7 × 10-4 min-1 for macrobubbles. Consequently, nanobubbles exhibit a much higher gas efficiency using 60% of O2 delivered to the system compared to 0.19% for macrobubbles. Further, it is observed that the electrogeneration of H2 O2 using carbon felt electrodes is enhanced using nanobubbles. Under the same dissolved oxygen levels, nanobubbles boost the reaction yield to 84%, while macrobubbles yield only 53.8%. To the authors' knowledge, this is the first study to investigate the use of nanobubbles in electrochemical reactions and demonstrate their ability to enhance gas efficiency and electrocatalytic response. These findings have important implications for developing more efficient chemical and electrochemical processes operating under gas-starving systems.

Inactivation of two oyster pathogens by photocatalysis and monitoring of changes in the microbiota of seawater: A case study on Ostreid herpes virus 1 μVar and Vibrio harveyi

The pollution of seawater by both biotic (bacteria, viruses) and abiotic contaminants (biocides, pharmaceutical residues) frequently leads to economic losses in aquaculture activities mostly mortality events caused by microbial infection. Advanced Oxidation Processes (AOPs) such as heterogeneous photocatalysis allow the removal of all organic contaminants present in water and therefore could reduce production losses in land-based farms. Oysters in land-based farms such as hatcheries and nurseries suffer from a large number of mortality events, resulting in significant losses. If photocatalysis has been widely studied for the decontamination, its application for disinfection is still overlooked, especially on seawater for viruses. We therefore studied seawater disinfection using the photocatalysis (UV365/TiO2) method in the context of Pacific oyster mortality syndrome (POMS). POMS has been defined as a polymicrobial disease involving an initial viral infection with Ostreid Herpes Virus 1, accompanied by multiple bacterial infections. We investigated the impact of treatment on Vibrio harveyi, a unique opportunistic pathogenic bacterium, and on a complex microbial community reflecting a natural POMS event. Viral inactivation was monitored using experimental infections to determine whether viral particles were still infectious after. Changes in the total bacterial community in seawater were studied by comparing UV365/TiO2 treatment with UV365-irradiated seawater and untreated seawater. In the case of OsHV-1, a 2-h photocatalytic treatment prevents POMS disease and oyster mortality. The same treatment also inactivates 80% of viable Vibrio harveyi culture (c.a. 1.5 log). Since OsHV-1 and Vibrio harveyi are effectively inactivated without long-term destabilization of the total bacterial microbiota in the seawater, photocatalysis appears to be a relevant alternative for disinfecting seawater in land-based oyster beds.