Novel determination of cadmium ions using an enzyme self-assembled monolayer with surface plasmon resonance

On the Strong Binding Affinity of Gold-Graphene Heterostructures with Heavy Metal Ions in Water: A Theoretical and Experimental Investigation

Minimum energy configurations in 2D material-based heterostructures can enable interactions with external chemical species that are not observable for their monolithic counterparts. Density functional theory (DFT) calculations reveal that the binding energy of divalent toxic metal ions of Cd, Pb, and Hg on graphene-gold heterointerfaces is negative, in contrast to the positive value associated with free-standing graphene. The theoretical predictions are confirmed experimentally by Surface Plasmon Resonance (SPR) spectroscopy, where a strong binding affinity is measured for all the heavy metal ions in water. The results indicate the formation of a film of heavy metal ions on the graphene-gold (Gr/Au) heterointerfaces, where the adsorption of the ions follows a Langmuir isotherm model. The highest thermodynamic affinity constant K = 3.1 × 107 L mol-1 is observed for Hg2+@Gr/Au heterostructures, compared to 1.1 × 107 L mol-1 and 8.5 × 106 L mol-1 for Pb2+@Gr/Au and Cd2+@Gr/Au, respectively. In the case of Hg2+ ions, it was observed a sensitivity of about 0.01°/ppb and a detection limit of 0.7 ppb (∼3 nmol L-1). The combined X-ray photoelectron spectroscopy (XPS) and SPR analysis suggests a permanent interaction of all of the HMIs with the Gr/Au heterointerfaces. The correlation between the theoretical and experimental results indicates that the electron transfer from the graphene-gold heterostructures to the heavy metal ions is the key for correct interpretation of the enhanced sensitivity of the SPR sensors in water.

Screening, separation and identification of metal-chelating peptides for nutritional, cosmetics and pharmaceutical applications

Metal-chelating peptides, which form metal-peptide coordination complexes with various metal ions, can be used as biofunctional ingredients notably to enhance human health and prevent diseases. This review aims to discuss recent insights into food-derived metal-chelating peptides, the strategies set up for their discovery, their study, and identification. After understanding the overall properties of metal-chelating peptides, their production from food-derived protein sources and their potential applications will be discussed, particularly in nutritional, cosmetics and pharmaceutical fields. In addition, the review provides an overview of the last decades of progress in discovering food-derived metal-chelating peptides, addressing several screening, separation and identification methodologies. Furthermore, it emphasizes the methods used to assess peptide-metal interaction, allowing for better understanding of chemical and thermodynamic parameters associated with the formation of peptide-metal coordination complexes, as well as the specific amino acid residues that play important roles in the metal ion coordination.

An overview of Structured Biosensors for Metal Ions Determination

The determination of metal ions is important for nutritional and toxicological assessment. Atomic spectrometric techniques are highly efficient for the determination of these species, but the high costs of acquisition and maintenance hinder the application of these techniques. Inexpensive alternatives for metallic element determination are based on dedicated biosensors. These devices mimic biological systems and convert biochemical processes into physical outputs and can be used for the sensitive and selective determination of chemical species such as cations. In this work, an overview of the proposed biosensors for metal ions determination was carried out considering the last 15 years of publications. Statistical data on the applications, response mechanisms, instrumentation designs, applications of nanomaterials, and multielement analysis are herein discussed.

Engineered Whole-Cell-Based Biosensors: Sensing Environmental Heavy Metal Pollutants in Water-a Review

The frequent exposure and accumulation of heavy metals in organisms cause serious health issues affecting a range of organs such as the brain, liver, and reproductive organs in adults, infants, and children. Several parts of the world have high levels of heavy metals affecting millions of people, costing millions of dollars for improving the potability of water and medical treatment of the affected. Hence, water quality assessment is required to monitor the degree of heavy metal contamination in potable water. In nature, organisms respond to various environmental pollutants such as heavy metals, allowing their survival in a diverse environmental niche. With the advent of recombinant DNA technology, it is now possible to manipulate these natural bioreporters into controlled systems which either turn on or off gene expression or activity of enzymes in the presence of specific heavy metals (compound-specific biosensors) otherwise termed as whole-cell biosensors (WCBs). WCBs provide an upper hand compared to other immunosensors, enzyme-based sensors, and DNA-based sensors since microbes can be relatively easily manipulated, scaled up with relative ease, and can detect only the bioavailable heavy metals. In this review, we summarize the current knowledge of the various mechanisms of toxicity elicited by various heavy metals, thence emphasizing the need to develop heavy metal sensing platforms. Following this, the biosensor-based platforms including WCBs for detecting heavy metals developed thus far have been briefly elaborated upon, emphasizing the challenges and solutions associated with WCBs.

Design and Optimization of Surface Plasmon Resonance Spectroscopy for Optical Constant Characterization and Potential Sensing Application: Theoretical and Experimental Approaches

The best surface plasmon resonance (SPR) signal can be generated based on several factors that include the excitation wavelength, the type of metal used, and the thickness of the metal layer. In this study, the aforementioned factors have been investigated to obtain the best SPR signal. The excitation wavelength of 633 nm and gold metal with thickness of 50 nm were required to generate the SPR signal before the SPR was used for optical constant characterization by fitting of experimental results to the theoretical data. The employed strategy has good agreement with the theoretical value where the real part refractive index, n value, of the gold thin film was 0.1245 while the value for the imaginary part, k, was 3.6812 with 47.7 nm thickness. Besides that, the optical characterization of nanocrystalline cellulose (NCC)-based thin film has also been demonstrated. The n and k values found for this thin film were 1.4240 and 0.2520, respectively, with optimal thickness of 9.5 nm. Interestingly when the NCC-based thin film was exposed to copper ion solution with n value of 1.3333 and k value of 0.0060 to 0.0070 with various concentrations (0.01–10 ppm), a clear change of the refractive index value was observed. This result suggests that the NCC-based thin film has high potential for copper ion sensing using SPR with a sensitivity of 8.0052°/RIU.

X-ray Photoelectron Spectroscopy Analysis of Chitosan-Graphene Oxide-Based Composite Thin Films for Potential Optical Sensing Applications

In this study, X-ray photoelectron spectroscopy (XPS) was used to study chitosan-graphene oxide (chitosan-GO) incorporated with 4-(2-pyridylazo)resorcinol (PAR) and cadmium sulfide quantum dot (CdS QD) composite thin films for the potential optical sensing of cobalt ions (Co2+). From the XPS results, it was confirmed that carbon, oxygen, and nitrogen elements existed on the PAR-chitosan-GO thin film, while for CdS QD-chitosan-GO, the existence of carbon, oxygen, cadmium, nitrogen, and sulfur were confirmed. Further deconvolution of each element using the Gaussian-Lorentzian curve fitting program revealed the sub-peak component of each element and hence the corresponding functional group was identified. Next, investigation using surface plasmon resonance (SPR) optical sensor proved that both chitosan-GO-based thin films were able to detect Co2+ as low as 0.01 ppm for both composite thin films, while the PAR had the higher binding affinity. The interaction of the Co2+ with the thin films was characterized again using XPS to confirm the functional group involved during the reaction. The XPS results proved that primary amino in the PAR-chitosan-GO thin film contributed more important role for the reaction with Co2+, as in agreement with the SPR results.

Enhancing the sensitivity of a surface plasmon resonance-based optical sensor for zinc ion detection by the modification of a gold thin film

Surface plasmon resonance (SPR) sensors as novel optical sensors for the detection of a variety of analytes have been receiving increasing attention and their sensitivity has become the research hotspot recently. In this study, the sensitivity of an SPR optical sensor was enhanced by modifying a gold thin film with a nanocrystalline cellulose (NCC)-based material for zinc ion (Zn2+) detection that exists in the environment due to industrial processing. By replacing the gold thin film with a novel modified-gold thin film, Zn2+ can be detected from the range of 0 to 10 ppm using SPR. It is believed that the Zn2+ may interact with the negative charge molecules that exist on the modified-gold thin film, and this was confirmed via X-ray photoelectron spectroscopy (XPS). Moreover, this modified-gold-SPR has a high sensitivity of 1.892° ppm-1 up to 0.1 ppm with an enhanced detection of Zn2+ as low as 0.01 ppm. The SPR results also followed the Langmuir isotherm model with a binding affinity of 1.927 × 103 M-1, which further confirmed the sensitivity of the SPR sensor. In addition, using the modified-gold thin film, SPR has a higher affinity towards Zn2+ compared to other metal ions, i.e. Ni2+, Fe2+, Cr2+, Mn2+, and Co2+.

Label-free optical spectroscopy for characterizing binding properties of highly sensitive nanocrystalline cellulose-graphene oxide based nanocomposite towards nickel ion

Surface plasmon resonance (SPR) is a label-free optical spectroscopy that is widely used for biomolecular interaction analysis. In this work, SPR was used to characterize the binding properties of highly sensitive nanocrystalline cellulose-graphene oxide based nanocomposite (CTA-NCC/GO) towards nickel ion. The formation of CTA-NCC/GO nanocomposite has been confirmed by FT-IR. The SPR analysis result shows that the CTA-NCC/GO has high binding affinity towards Ni²⁺ from 0.01 until 0.1 ppm with binding affinity constant of 1.620 × 10³ M^-1. The sensitivity for the CTA-NCC/GO calculated was 1.509° ppm^-1. The full width at half maximum (FWHM), data accuracy (DA), and signal-to-noise ratio (SNR) have also been determined using the obtained SPR curve. For the FWHM, the value was 2.25° at 0.01 until 0.08 ppm and decreases to 2.12° at 0.1 until 10 ppm. The DA for the SPR curves is the highest at 0.01 until 0.08 ppm and lowest at 0.1 until 10 ppm. The SNR curves mirrors the curves of SPR angle shift where the SNR increases with the Ni²⁺ concentrations. For the selectivity test, the CTA-NCC/GO has the abilities to differentiate Ni²⁺ in the mixture of metal ions.

A Localized Surface Plasmon Resonance Sensor Using Double-Metal-Complex Nanostructures and a Review of Recent Approaches

From active developments and applications of various devices to acquire outside and inside information and to operate based on feedback from that information, the sensor market is growing rapidly. In accordance to this trend, the surface plasmon resonance (SPR) sensor, an optical sensor, has been actively developed for high-sensitivity real-time detection. In this study, the fundamentals of SPR sensors and recent approaches for enhancing sensing performance are reported. In the section on the fundamentals of SPR sensors, a brief description of surface plasmon phenomena, SPR, SPR-based sensing applications, and several configuration types of SPR sensors are introduced. In addition, advanced nanotechnology- and nanofabrication-based techniques for improving the sensing performance of SPR sensors are proposed: (1) localized SPR (LSPR) using nanostructures or nanoparticles; (2) long-range SPR (LRSPR); and (3) double-metal-layer SPR sensors for additional performance improvements. Consequently, a high-sensitivity, high-biocompatibility SPR sensor method is suggested. Moreover, we briefly describe issues (miniaturization and communication technology integration) for future SPR sensors.

A metal-responsive interdigitated bilayer for selective quantification of mercury(ii) traces by surface plasmon resonance

An innovative design of reusable SPR chips allowing the quantitative and selective determination of mercury(ii) at the ppt level is reported.

Development of surface plasmon resonance sensor for determining zinc ion using novel active nanolayers as probe

In this study, novel active nanolayers in combination with surface plasmon resonance (SPR) system for zinc ion (Zn(2+)) detection has been developed. The gold surface used for the SPR system was modified with the novel developed active nanolayers, i.e. chitosan and chitosan-tetrabutyl thiuram disulfide (chitosan-TBTDS). Both chitosan and chitosan-TBTDS active layers were fabricated on the gold surface by spin coating technique. The system was used to monitor SPR signal for Zn(2+) in aqueous media with and without sensitivity enhancement by TBTDS. For both active nanolayers, the shift of resonance angle is directly proportional to the concentration of Zn(2+) in aqueous media. The higher shift of resonance angle was obtained for chitosan-TBTDS active nanolayer due to a specific binding of TBTDS with Zn(2+). The chitosan-TBTDS active nanolayer enhanced the sensitivity of detection down to 0.1 mg/l and also induced a selective detection towards Zn(2+).

Performance Evaluation of Monolith Based Immobilized Acetylcholinesterase Flow-Through Reactor for Copper(II) Determination with Spectrophotometric Detection

A monolith based immobilized acetylcholinesterase (AChE) flow-through reactor has been developed for the determination of copper(II) using flow injection spectrophotometric system. The bioreactor was prepared inside a microcapillary column byin situpolymerization of butyl methacrylate, ethylene dimethacrylate, and 2,2-dimethoxy-1,2-diphynyletane-1-one in the presence of 1-decanol, followed by vinyl azlactone functionalization and AChE immobilization. The behavior of AChE before and after being immobilized on the monolith was evaluated by kinetic parameters from Lineweaver and Burk equation. The detection was based on measuring inhibition effect on the enzymatic activity of AChE by copper(II) using Ellman’s reaction with spectrophotometric detection at 410 nm. The linear range of the calibration graph was obtained over the range of 0.02–3.00 mg L−1. The detection limit, defined as 10% inhibition (I10), was found to be 0.04 mg L−1. The repeatability was 3.35 % (n=5) for 1.00 mg L−1of copper(II). The proposed method was applied to the determination of copper(II) in natural water samples with sampling rate of 4 h−1.

Recent developments and applications of hybrid surface plasmon resonance interfaces in optical sensing

Nanostructured noble metals exhibit an intense optical near field due to surface plasmon resonance, therefore promising widespread applications and being of interest to a broad spectrum of scientists, ranging from physicists, chemists, and materials scientists to biologists. A wealth of research is available discussing the synthesis, characterization, and application of noble metal nanoparticles in optical sensing. However, with respect to the sensitivity of the frequency and width of these surface plasmon resonance modes to the particle's shape, size, and environment, in nearly every case, success strongly depends on the availability of highly stable, adhesive, and sensitive nanoparticles. This undoubtedly presents a challenging task to nanofabrication. The past decade has witnessed fascinating advances in this field, in particular, the construction of oxide-based hybrid plasmonic interfaces to overcome the problem addressed above by (1) coating the metallic nanostructures with thin overlayers to form sandwiched structures or (2) embedding metallic nanostructures in a dielectric matrix to obtain metal/dielectric matrix nanocomposite films. In this critical review, we focus on recent work related to this field, beginning with a presentation of hybrid films with enhanced structural and optical stability, readily and selectively designed using chemical and physical techniques. We then illustrate their interesting optical properties and demonstrate exciting evidence for the postulated application in surface plasmon sensing fields. Finally, we survey the work remaining to be done for that potential to be realized.

Electrochemical microsensors for the detection of cadmium(II) and lead(II) ions in plants

Routine determination of trace metals in complex media is still a difficult task for many analytical instruments. The aim of this work was to compare three electro-chemical instruments [a standard potentiostat (Autolab), a commercially available miniaturized potentiostat (PalmSens) and a homemade micropotentiostat] for easy-to-use and sensitive determination of cadmium(II) and lead(II) ions. The lowest detection limits (hundreds of pM) for both metals was achieved by using of the standard potentiostat, followed by the miniaturized potentiostat (tens of nM) and the homemade instrument (hundreds of nM). Nevertheless, all potentiostats were sensitive enough to evaluate contamination of the environment, because the environmental limits for both metals are higher than detection limits of the instruments. Further, we tested all used potentiostats and working electrodes on analysis of environmental samples (rainwater, flour and plant extract) with artificially added cadmium(II) and lead(II). Based on the similar results obtained for all potentiostats we choose a homemade instrument with a carbon tip working electrode for our subsequent environmental experiments, in which we analyzed maize and sunflower seedlings and rainwater obtained from various sites in the Czech Republic.

Recent biosensing developments in environmental security

Environmental security is one of the fundamental requirements of our well being. However, it still remains a major global challenge. Therefore, in addition to reducing and/or eliminating the amounts of toxic discharges into the environment, there is need to develop techniques that can detect and monitor these environmental pollutants in a sensitive and selective manner to enable effective remediation. Because of their integrated nature, biosensors are ideal for environmental monitoring and detection as they can be portable and provide selective and sensitive rapid responses in real time. In this review we discuss the main concepts behind the development of biosensors that have most relevant applications in the field of environmental monitoring and detection. We also review and document recent trends and challenges in biosensor research and development particularly in the detection of species of environmental significance such as organophosphate nerve agents, heavy metals, organic contaminants, pathogenic microorganisms and their toxins. Special focus will be given to the trends that have the most promising applications in environmental security. We conclude by highlighting the directions towards which future biosensors research in environmental security sector might proceed.

Cholesterol biosensor based on amino-undecanethiol self-assembled monolayer using surface plasmon resonance technique

Cholesterol oxidase has been covalently immobilized onto 11-amino-1-undecanethiol hydrochloride (AUT) self-assembled monolayer (SAM) fabricated on gold (Au) substrates using glutaraldehyde as a cross-linker. These ChOx/AUT/Au bioelectrodes characterized using contact angle (CA) measurements; electrochemical technique and atomic force microscopy (AFM) have been utilized for the estimation of cholesterol in solution using the surface plasmon resonance (SPR) technique. These biosensing electrodes exhibiting linearity from 50 to 500 mg/dL of cholesterol in solution and sensitivity of 1.23 m0/(mg dL), can be used more than 20 times and have a shelf life of about 10 weeks when stored at 4 degrees C.

Preparation and characterization of urease-encapsulated biosensors in poly(vinyl alcohol)-modified silica sol-gel materials

The microenvironments of the sol-gel-derived urease biosensors in terms of elemental ratio, surface morphology, specific surface area and pore size were investigated to characterize the physicochemical properties of poly(vinyl alcohol) (PVA)-modified sol-gel materials. X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM) and surface area analyzer were used to identify the surface species, topography and pore distribution of the organically doped sol-gel network. XPS results showed that stoichiometric ratios of oxygen-to-silicon in sol-gel materials were in the range 2.08-2.11. The sol-gel materials were partially dried and negatively charged, which retained 6-8% water content to maintain urease activity. The surface morphology of the sol-gel altered obviously when macromolecules were encapsulated, resulting in the increase in surface mean roughness from 0.207 to 2.636 nm. The specific surface area decreased dramatically after the immobilization of biomolecules and organic additives, which clearly depicts that PVA and urease were co-encapsulated into the sol-gel network. However, there still exist enough pore volumes for analytes to mass transport. The apparent Michaelis-Menten constant value (Km) of the encapsulated urease was similar to that in solution and the overall catalytic efficiency in PVA-doped sol-gel-derived glasses only decreased by a factor of 3.2 relative to the value in solution. In addition, the analytical performance of the entrapped urease in PVA-doped sol-gel materials was examined by determining the Cu(II) concentration in aqueous solution. The analytical range of Cu(II) was in the range 2x10(-6) to 2x10(-2) M with a detection limit of 1.5 microg L(-1). Results obtained in this study demonstrate a strategy for maintaining urease activity for biomedical and environmental applications.

Enzyme inhibition-based biosensors for food safety and environmental monitoring

Analytical technology based on sensors is an extremely broad field which impacts on many major industrial sectors such as the pharmaceutical, healthcare, food, and agriculture industries as well as environmental monitoring. This review will highlight the research carried out during the last 5 years on biosensors that are based on enzyme inhibition for determination of pollutants and toxic compounds in a wide range of samples. Here the different enzymes implicated in the inhibition, different transducers forming the sensing devices, and the different contaminants analyzed are considered. The general application of the various biosensors developed, with emphasis on food and environmental applications, is reviewed as well as the general approaches that have been used for enzyme immobilization, the enzyme catalysis, and the inhibition mechanism.

Investigation of pH-dependent DNA-metal ion interactions by surface plasmon resonance

Ni(II) and Zn(II) M-DNA formation and denaturation of double-stranded DNA (dsDNA) by Cd(2+) were monitored by surface plasmon resonance (SPR). When exposed to immobilized 30 bp 50% GC dsDNA, Zn(2+) and Ni(2+) were found to give signals indicative of a conformational change at pH 8.5 but not 7.5, while Mg(2+) and Ca(2+) caused small changes at both pHs. The concentrations that gave 50% of the maximum responses were 0.06 and 0.50 mM for Zn(2+) and Ni(2+), respectively. At pH 8.5, Cd(2+) denatured over 40% of the dsDNA, while other metals denatured less than 5% of the DNA. Smaller pH-dependent signals were induced by Zn(2+), Ni(2+) or Cd(2+) with 50% GC single-stranded DNA (ssDNA), and with a homopolymer of d(T)30. Homopolymers d(A)30 and d(C)30 showed small signals that were largely independent of pH in the presence of Zn(2+) or Ni(2+).

Survey of the year 2003 commercial optical biosensor literature

In the year 2003 there was a 17% increase in the number of publications citing work performed using optical biosensor technology compared with the previous year. We collated the 962 total papers for 2003, identified the geographical regions where the work was performed, highlighted the instrument types on which it was carried out, and segregated the papers by biological system. In this overview, we spotlight 13 papers that should be on everyone's 'must read' list for 2003 and provide examples of how to identify and interpret high-quality biosensor data. Although we still find that the literature is replete with poorly performed experiments, over-interpreted results and a general lack of understanding of data analysis, we are optimistic that these shortcomings will be addressed as biosensor technology continues to mature.